编号 | 中文名称 | 英文名称 |
---|---|---|
ANSI/ASTM D2802-2003 | 电线和电缆用耐臭氧乙丙橡胶绝缘材料规范 | Specification for Ozone-Resistant Ethylene-Propylene Rubber Insulation for Wire and Cable |
ANSI/ASTM D4245-2002 | 工作温度为90℃干/75℃湿的电线和电缆的耐臭氧热塑性合成橡胶绝缘规范 | Specification for Ozone-Resistant Thermoplastic Elastomer Insulation for Wire and Cable 90oC Dry/75oC Wet Operation |
ANSI/ASTM D4246-2002 | 工作温度为90℃的电线和电缆的耐臭氧热塑性合成橡胶绝缘规范 | Specification for Ozone-Resistant Thermoplastic Elastomer Insulation for Wire and Cable, 90oC Operation |
ANSI/EIA 364-14B-1999 | 电连接器.臭氧暴露试验程序 | Ozone Exposure Test Procedure for Electrical Connectors |
ANSI/EIA-364-14B-1999 | 电连接器.臭氧暴露试验程序 | Ozone Exposure Test Procedure for Electrical Connectors |
ANSI/NSF 222-2006 | 臭氧发生器 | NSF 222 - Ozone Generators |
ASTM D1149-2007 | 臭氧可控环境中橡胶变坏龟裂的标准试验方法 | Standard Test Methods for Rubber Deterioration-Cracking in an Ozone Controlled Environment |
ASTM D2802-2003 | 电线及电缆用耐臭氧乙烯烃聚合物绝缘材料的标准规范 | Standard Specification for Ozone-Resistant Ethylene-Alkene Polymer Insulation for Wire and Cable |
ASTM D3156-1996(2005) | 橡胶的标准实施规程.防降解剂(防氧化剂、防臭氧剂及稳定剂)的色谱分析 | Standard Practice for Rubber&8212;Chromatographic Analysis of Antidegradants (Antioxidants, Antiozonants and Stabilizers) |
ASTM D4246-2002 | 在90℃时电线和电缆的耐臭氧热塑性弹性体绝缘的标准规范 | Standard Specification for Ozone-Resistant Thermoplastic Elastomer Insulation For Wire and Cable, 90&176C Operation |
ASTM D4575-1999(2005) | 橡胶变质的标准试验方法.测定实验室测试小室内臭氧浓度的参照法和交替法 | Standard Test Methods for Rubber Deterioration&8212;Reference and Alternative Method(s) for Determining Ozone Level in Laboratory Test Chambers |
ASTM D5011-1992(2003) | 使用传送标准对臭氧检测器的校验 | Standard Practices for Calibration of Ozone Monitors Using Transfer Standards |
ASTM D5110-1998(2004) | 使用紫外光度法进行臭氧转变标准认证和臭氧监测器校准的标准实施规范 | Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry |
BS 1747-12-1993 | 空气污染测量方法.环境空气中臭氧质量浓度的测定:化学荧光法 | Methods for measurement of air pollution - Determination of the mass concentration of ozone in ambient air: chemiluminescence method |
BS EN 1278-1999 | 供人用的水处理时用的化学物质.臭氧 | Chemicals used for treatment of water intended for human consumption - Ozone |
BS EN 14625-2005 | 环境空气质量.用紫外线光度测量法测量臭氧浓度的标准方法 | Ambient air quality - Standard method for the measurement of the concentration of ozone by ultraviolet photometry |
BS EN 15074-2008 | 游泳池水处理用化学试剂.臭氧 | Chemicals used for treatment of swimming pool water - Ozone |
BS EN 1844-2001 | 防水柔性板.耐臭氧性测定.屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing |
BS EN 2349-409-2007 | 航空航天系列.继电器和电流接触器的要求和试验程序.抗臭氧 | Aerospace series — Requirements and test procedures for relays and contactors — Part 409: Ozone resistance |
BS EN 2591-316-1998 | 光电连接元件.试验方法.耐臭氧 | Elements of electrical and optical connection - Test methods - Ozone resistance |
BS EN 2591-6316-2001 | 电气和光学连接元件.试验方法.光学元件.耐臭氧性能 | Elements of electrical and optical connection - Test methods - Optical elements - Ozone resistance |
BS EN 60811-2-1-1998 | 电缆绝缘和护套材料.通用试验方法.弹性化合物专用试验方法.耐臭氧性、热固化及矿物油浸渍试验 | Insulating and sheathing materials of electric cables - Common test methods - Methods specific to elastomeric compounds - Methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests |
BS EN ISO 105-G03-1997 | 纺织品.色牢度试验.第G03部分:耐大气臭氧色牢度 | Textiles - Tests for colour fastness - Colour fastness to ozone in the atmosphere |
BS EN ISO 10960-1997 | 橡胶和塑料软管.在动态条件下耐臭氧性的评定 | Rubber and plastic hoses - Assessment of ozone resistance under dynamic conditions |
BS EN ISO 15011-2-2003 | 焊接和相关工艺的卫生和安全.电弧焊产生的烟和气体取样的实验室法.除臭氧外的气体排放率的测定 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Determination of emission rates of gases, except ozone |
BS EN ISO 7326-2008 | 橡胶和塑料软管.静态条件下评定耐臭氧性 | Rubber and plastics hoses - Assessment of ozone resistance under static conditions |
BS ISO 1431-1-2004 | 硫化橡胶或热塑性橡胶.耐臭氧龟裂性.静态和动态应变试验 | Rubber, vulcanized or thermoplastic - Resistance to ozone cracking - Static and dynamic strain testing |
BS ISO 1431-3-2000 | 硫化橡胶或热塑橡胶.耐臭氧龟裂性.在实验室试验测定臭氧浓度的标准方法和替用方法 | Rubber, vulcanized or thermoplastic - Resistance to ozone cracking - Reference and alternative methods for determining the ozone concentration in laboratory test chambers |
BS ISO 3011-1997 | 橡胶或塑料涂层织物.静态条件下抗臭氧龟裂的测定 | Rubber- or plastics-coated fabrics - Determination of resistance to ozone cracking under static conditions |
DIN 19627-1993 | 水处理用臭氧设备 | Ozone-plants for water treatment |
DIN 19643-3-1997 | 游泳池和洗浴用水的处理.第3部分:处理方法组合:絮凝作用、过滤作用、臭氧消毒处理、吸附过滤和氯化作用 | Treatment of water of swimming-pools and baths - Part 3: Combination of process: Flocculation, filtration, ozonization, absorbing filtration, chlorination |
DIN 19643-4-1999 | 游泳池和洗澡池水的处理.第4部分:方法组合:絮凝作用、臭氧消毒法、多层过滤和氯化作用 | Treatment of water of swimming pools and baths - Part 4: Combination of process: Flocculation, ozonisation, multilayer filtration, chlorination |
DIN 38408-3-1993 | 德国检验水、废水和污泥的标准方法.气态组份(G组),臭氧的测定(G 3) | German standard methods for the examination of water, waste water and sludge; gaseous components (group G); determination of ozone (G 3) |
DIN 53509-1-2001 | 橡胶试验.抗臭氧龟裂的测定.第1部分:静态条件 | Testing of rubber - Determination of resistance to ozone cracking - Part 1: Static conditions |
DIN 53509-2-1994 | 橡胶的检验.抗臭氧裂化的测定.第2部分:在试验室测试间测定臭氧浓度的基准方法 | Testing of rubber - Determination of resistance to ozone cracking - Part 2: Reference method for determining ozone concentration in laboratory test chambers |
DIN EN 1278-1999 | 饮用水处理用化学品.臭氧 | Chemicals used for treatment of water intended for human consumption - Ozone; German version EN 1278:1998 |
DIN EN 14625-2005 | 环境空气质量.用紫外线光度测量法测量臭氧浓度的标准方法 | Ambient air quality - Standard method for the measurement of the concentration of ozone by ultraviolet photometry; German version EN 14625:2005 |
DIN EN 15074-2006 | 游泳池水处理用化学制品.臭氧 | Chemicals used for treatment of swimming pool water - Ozone English version of DIN EN 15074:2006-08 |
DIN EN 1844-2001 | 防水软板.耐臭氧性测定.屋顶防水塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing; German version EN 1844:2001 |
DIN EN 2349-409-2008 | 航空航天系列.继电器和电流接触器的要求和试验程序.第409部分:耐臭氧性 | Aerospace series - Requirements and test procedures for relays and contactors - Part 409: Ozone resistance; German and English version EN 2349-409:2007 |
DIN EN 2591-316-1997 | 航空航天系列.光电连接件.试验方法.第316部分:耐臭氧 | Aerospace series - Elements of electrical and optical connection; test methods - Part 316: Ozone resistance; German version EN 2591-316:1997 |
DIN EN 2591-6316-2003 | 航空航天系列.光电连接件.试验方法.第6316部分:光学元件.耐臭氧性 | Aerospace series - Elements of electrical and optical connection; Test methods - Part 6316: Optical elements; Ozone resistance; German and English version EN 2591-6316:2001 |
DIN EN 27326-1993 | 橡胶和塑料软管.静态条件下耐臭氧性能的评定 | Rubber and plastics hoses; assessment of ozone resistance under static conditions (ISO 7326:1991); German version EN 27326:1993 |
DIN EN 60811-2-1-2002 | 电缆和光缆的绝缘和护套材料.通用试验方法.第2-1部分:弹性体专用试验方法.耐臭氧性、热固和矿物油浸试验 | Insulating and sheathing materials of electric and optical cables - Common test methods - Part 2-1: Methods specific to elastomeric compounds; Ozone resistance, hot set and mineral oil immersion tests (IEC 60811-2-1:1998 + A1:2001); German version EN 60811-2-1:1998 + A1:2001 |
DIN EN ISO 105-G03-1997 | 纺织品.色牢度试验.第G03部分:耐大气臭氧色牢度测定 | Textiles - Tests for colour fastness - Part G03: Colour fastness to ozone in the atmosphere (ISO 105-G03:1993); German version EN ISO 105-G03:1997 |
DIN EN ISO 10960-1996 | 橡胶和塑料软管.动态耐臭氧性评估 | Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions (ISO 10960:1994); German version EN ISO 10960:1996 |
DIN EN ISO 15011-2-2003 | 焊接和相关工艺中的保健和安全.对电弧焊产生的烟尘和气体取样的实验室方法.第2部分:除臭氧外气体的排放率的 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2: Determination of emission rates of gases, except ozone (ISO 15011-2:2003); German version EN ISO 15011-2:2003 |
DIN EN ISO 15011-3-2003 | 焊接和相关工艺的卫生和安全.电弧焊烟和气体的实验室取样法.第3部分:固定点法测定臭氧浓度 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 3: Determination of ozone concentration using fixed point measurements (ISO 15011-3:2002); German version EN ISO 15011-3:2002 |
DIN ISO 13964-1999 | 空气质量.环境空气中臭氧含量测定.紫外分光光度法 | Air quality - Determination of ozone in ambient air - Ultraviolet photometric method (ISO 13964:1998) |
EN 1278-1998 | 民用水处理用化学药剂 臭氧 | Chemicals used for treatment of water intended for human consumption - Ozone |
EN 1278/prA1-2000 | 民用水处理用化学药剂 臭氧 修正A1 | Chemicals used for treatment of water intended for human consumption - Ozone; Amendment A1 |
EN 1844-2001 | 防水热塑性及弹性薄板 耐臭氧性的测定 屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing |
EN 2591-316-1997 | 航空航天系列 光电连接元件 试验方法 第316部分:抗臭氧 | Aerospace series - Elements of electrical and optical connection - Test methods - Part 316: Ozone resistance |
EN 2591-6316-2001 | 航空航天系列 光电连接元件 试验方法 第6316部分:光学元件 耐臭氧 | Aerospace series - Elements of electrical and optical connection; Test methods - Part 6316: Optical elements; Ozone resistance |
EN 27326-1993 | 橡胶和塑料软管 静态条件下耐臭氧性的评定 | Rubber and plastics hoses-Assessment of ozone resistance under static conditions (ISO 7326:1991) |
EN 60811-2-1-1998+A1-2001 | 电缆绝缘和护套材料 通用试验方法 第2-1部分:合成橡胶专用方法 抗臭氧试验 热固试验和矿物油浸试验 | Insulating and sheathing materials of electric and optical cables - Common test methods - Part 2-1: Methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests (IEC 60811-2-1:1998) |
EN ISO 105-G03-1997 | 纺织品 色牢度试验 第G03部分:耐大气臭氧色牢度 | Textiles - Tests for colour fastness - Part G03: Colour fastness to ozone in the atmosphere (ISO 105-G03:1993) |
EN ISO 10960-1996 | 橡胶和塑料软管 动态条件下耐臭氧性的评定 | Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions (ISO 10960:1994) |
EN ISO 15011-2-2003 | 焊接和有关工艺中的健康和安全 电弧焊产生的烟尘和气体取样的实验室方法 第2部分:除臭氧外、各种气体产 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2: Determination of emission rates of gases, except ozone (ISO 15011-2:2003) |
EN ISO 15011-3-2002 | 焊接和有关工艺中的健康和安全 电弧焊产生的烟尘和气体取样的实验室方法 第3部分:在固定点测定臭氧浓度 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 3: Determination of ozone concentration using fixed point measurements (ISO 15011-3:2002) |
GB 18066-2000 | 居住区大气中臭氧卫生标准 | Hygienic standard for ozone in air of residential areas |
GB/T 11039.3-2005 | 纺织品 色牢度试验 耐大气污染物色牢度 第3部分:大气臭氧 | Textiles-Tests for colour fastness-Colour fastness to Contaminants part3:ozone in the atmosphere |
GB/T 13642-1992 | 硫化橡胶耐臭氧老化试验动态拉伸试验法 | Rubber,vulcanized--Resistance to ozone ageing--Dynamic strain test method |
GB/T 15437-1995 | 环境空气臭氧的测定靛蓝二磺酸钠分光光度法 | Ambient air--Determination of ozone--Indigo disulphonate spectrophotometry |
GB/T 15438-1995 | 环境空气臭氧的测定紫外光度法 | Ambient air--Determination of ozone--Ultraviolet photometric method |
GB/T 18202-2000 | 室内空气中臭氧卫生标准 | Hygienic standard for ozone in indoor air |
GB/T 18204.27-2000 | 公共场所空气中臭氧测定方法 | Method of examination of ozone in air of public places |
GB/T 18949-2003 | 橡胶和塑料软管动态条件下耐臭氧性能的评定 | Rubber and plastics hoses--Assessment of ozone resistance under dynamic conditions |
GB/T 24134-2009 | 橡胶和塑料软管 静态条件下耐臭氧性能的评价 | () |
GB/T 2951.21-2008 | 电缆和光缆绝缘和护套材料通用试验方法 第21部分:弹性体混合料专用试验方法 耐臭氧试验-热延伸试验-浸矿物 | Common test methods for insulating and sheathing materials of electric and optical cables - Part 21:Methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests |
GB/T 7762-2003 | 硫化橡胶或热塑性橡胶耐臭氧龟裂静态拉伸试验 | Rubber,vulcanized or thermoplastic--Resistance to ozone cracking--Static strain test |
HG/T 2716-2008 | 橡胶或塑料涂覆织物 静态耐臭氧龟裂性能的测定 | () |
HG/T 2869-1997 | 橡胶和塑料软管 静态条件下耐臭氧性能的评价 | () |
IEC 60811-2-1 AMD 1-2001 | 电缆和光缆用绝缘和护套材料 通用试验方法 第2-1部分:弹性化合物专用方法 耐臭氧试验、热凝固试验和矿物 | Common test methods for insulating and sheathing materials of electric and optical cables - Part 2-1: Methods specific to elastomeric compounds; Ozone resistance, hot set and mineral oil immersion tests; Amendment 1 |
IEC 60811-2-1 Edition 2.1-2001 | 电缆和光缆用绝缘和屏蔽材料的共同试验方法.第2-1部分:弹性体所用特定方法.臭氧抗性、热固和矿物油浸试验 | Common test methods for insulating and sheathing materials of electric and optical cables - Part 2-1: Methods specific to elastomeric compounds; Ozone resistance, hot set and mineral oil immersion tests |
IEC 60811-2-1-1998 | 电缆和光缆用绝缘和护套材料 通用试验方法 第2-1部分:弹性化合物专用方法 耐臭氧试验、热凝固试验和矿物油 | Insulating and sheathing materials of electric and optical cables - Common test methods - Part 2-1: Methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests |
ISO 10313-1993 | 环境空气 臭氧质量浓度的测定 化学发光法 | Ambient air; determination of the mass concentration of ozone; chemiluminescence method |
ISO 105-G03-1993 | 纺织品 色牢度试验 第G03部分:耐大气臭氧色牢度 | Textiles; tests for colour fastness; part G03: colour fastness to ozone in the atmosphere |
ISO 10960-1994 | 橡胶和塑料软管 动态条件下耐臭氧性的评定 | Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions |
ISO 13964-1998 | 空气质量 环境空气中臭氧的测定 紫外分光光度法 | Air quality - Determination of ozone in ambient air - Ultraviolet photometric method |
ISO 1431-1-2004 | 硫化或热塑性橡胶.耐臭氧龟裂.第1部分:静态和动态应变试验 | Rubber, vulcanized or thermoplastic - Resistance to ozone cracking - Part 1: Static and dynamic strain testing |
ISO 1431-3-2000 | 硫化或热塑性橡胶 耐臭氧龟裂 第3部分:实验室试验箱内测定臭氧浓度的推荐的和可选用的方法 | Rubber, vulcanized or thermoplastic - Resistance to ozone cracking - Part 3: Reference and alternative methods for determining the ozone concentration in laboratory test chambers |
ISO 15011-2-2003 | 焊接和相关工艺中的保健和安全.对电弧焊产生的烟尘和气体取样的实验室方法.第2部分:除臭氧外气体的排放率的 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2: Determination of emission rates of gases, except ozone |
ISO 3011-1997 | 橡胶或塑料涂覆织物 静态条件下抗臭氧龟裂的测定 | Rubber- or plastics-coated fabrics - Determination of resistance to ozone cracking under static conditions |
ISO 6235-1995 | 生胶 嵌段聚苯乙烯含量的测定 臭氧分解法 | Rubber, raw - Determination of block polystyrene content - Ozonolysis method |
ISO 7326-2006 | 橡胶和塑料软管.静态条件下评定耐臭氧性 | Rubber and plastics hoses - Assessment of ozone resistance under static conditions |
JC/T 426-1998 | 无臭氧石英玻璃管 | () |
JIS B7957-2006 | 环境空气中臭氧和氧化剂的连续分析仪 大気中のオゾン及びオキシダントの自動計測器 | Continuous analyzers for ozone and oxidants in ambient air |
JIS C3660-2-1-2003 | 电缆和光缆的绝缘和铠装材料的通用试验方法.第2-1部分:弹性复合物专用方法.耐臭氧、热固及矿物油浸渍试验 電気・光ケーブルの絶縁体及びシース材料の共通試験方法 ― 第2-1部:エラストマーの特性試験方法 ― オゾン,ホットセット及び耐油試験 | Common test methods for insulating and sheathing materials of electric and optical cables -- Part 2-1: Methods specific to elastomeric compounds -- Ozone resistance, hot set and mineral oil immersion tests |
JIS K6259-2004 | 硫化或热塑性橡胶.耐臭氧的测定 加硫ゴム及び熱可塑性ゴム―耐オゾン性の求め方 | Rubber, vulcanized or thermoplastics -- Determination of ozone resistance |
JIS K6330-7-1998 | 橡胶和塑料软管的测试方法.第7部分:静态条件下对臭氧抗性的评估 ゴム及び樹脂ホース試験方法 ― 第7部:静的オゾン劣化試験 | Testing methods for rubber and plastics hoses -- Part 7: Assessment of ozone resistance under static conditions |
JIS K6404-19-1999 | 橡胶或塑料涂覆织物的试验方法.第19部分:耐臭氧龟裂的测定 ゴム引布・プラスチック引布試験方法 ― 第19部:オゾン劣化試験 | Testing methods for rubber-or plastics-coated fabrics -- Part 19: Determination of resistance to ozone cracking |
JIS L0890-2006 | 臭氧色牢度的试验方法 オゾンに対する染色堅ろう度試験方法 | Test methods for colour fastness to ozone |
JIS X6936-2005 | 信息技术.办公室设备.复印机、打印机和多功能设备的臭氧、挥发性有机化合物和灰尘的散发率测量 事務機器-オゾン,揮発性有機化合物及び粉じんの放散量測定方法 | Information technology -- Office equipment -- Measurement of ozone, volatile organic compounds and dust emissions rate from copiers, printers and multi-function devices |
NF A88-200-2-2003 | 焊接和相关工艺中的卫生和安全.对电弧焊产生的烟尘和气体取样的实验室方法.第2部分:除臭氧外气体的排放率测 | (Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2 : determination of emission rates of gases, except ozone.) |
NF A88-200-3-2003 | 焊接和相关工艺中的卫生和安全.对电弧焊产生的烟尘和气体取样的实验室方法.第3部分:用固定点测量法测定臭氧 | (Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 3 : determination of ozone concentration using fixed point measurement) |
NF C32-028-1999 | 电缆和光缆用绝缘和屏蔽材料.一般试验方法.第2-1部分:弹性体所用特定方法.臭氧抗性,热固和矿物油浸试验 | (Insulating and sheating materials of electric and optical cables - Common test methods - Part 2-1 : methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests.) |
NF C32-028/A1-2002 | 电缆和光缆用绝缘材料和护套材料.通用试验方法.第2-1部分:专用于弹性化合物的方法.耐臭氧性、热固和矿物油 | (Insulating and sheathing materials of electric and optical cables - Common test methods - Part 2-1 : methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tes) |
NF G07-071-3-1997 | 纺织.色牢度试验.第G03部分:大气中耐臭氧色牢度(欧洲标准EN ISO 105-G03) | (TEXTILES. TESTS FOR COLOUR FASTNESS. PART G03 : COLOUR FASTNESS TO OZONE IN THE ATMOSPHERE. (EUROPEAN STANDARD EN ISO 105-G03).) |
NF G37-112-1980 | 橡胶或塑料涂层织物.抗臭氧的静态试验 | (Fabrics coated with rubber or plastic-static ozone resistance test.) |
NF L54-002-035-1998 | 航空航天系列.电气及光学连接的元件.试验方法.第316部分:臭氧抗性 | (Aerospace series. Elements of electrical and optical connection. Test methods. Part 316 : ozone resistance.) |
NF L54-002-119-2002 | 航空航天系列.电气及光学连接元件.试验方法.第6316部分:光学元件.耐臭氧性 | (Aerospace series - Elements of electrical and optical connection - Test methods - Part 6316 : optical elements - Ozone resistance.) |
NF P84-112-2002 | 防水软板.耐臭氧性测定.屋顶防水用塑料和橡胶薄板 | (Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing.) |
NF T46-019-1992 | 硫化或热塑橡胶.抗臭氧开裂.静态变形试验 | (Vulcanized or thermoplastic rubber. Resistance to ozone cracking. Static elongation test.) |
NF T46-038-1995 | 硫化或热塑橡胶.抗臭氧开裂.实验室试验室中臭氧浓度测定用参考法和选择法 | (Rubber vulcanized of thermoplastic. Resistance to ozone cracking. Reference and alternative methods for determining ozone concentration in laboratory test chambers.) |
NF T46-039-1992 | 硫化或热塑橡胶.抗臭氧开裂.动态变形试验 | (Vulcanized or thermoplastic rubber. Resistance to ozone cracking. Dynamic deformation test.) |
NF T47-205-1993 | 橡胶和塑料软管.静态条件下的耐臭氧性试验的评定 | (Rubber and platics hoses. Assessment of ozone resistance under static conditions.) |
NF T47-218-1996 | 橡胶和塑料软管.在动力条件下耐臭氧性的评定(欧洲标准EN ISO 10960) | (RUBBER AND PLASTICS HOSES. ASSESSMENT OF OZONE RESISTANCE UNDER DYNAMIC CONDITIONS. (EUROPEAN STANDARD EN ISO 10960).) |
NF T94-306-1998 | 人类用水的处理试剂.臭氧(欧洲标准EN 1278) | (CHEMICALS USED FOR TREATMENT OF WATER INTENTED FOR HUMAN CONSUMPTION. OZONE. (EUROPEAN STANDARD EN 1278).) |
prEN 2349-409-2000 | 航空航天系列 继电器和接触器要求和试验程序 第409部分:耐臭氧腐蚀性 | Aerospace series - Requirements and test procedures for relays and contactors - Part 409: Ozone resistance |
编号 | 中文名称 | 英文名称 |