| 编号 | 中文名称 | 英文名称 |
|---|
| ANSI/ASTM B649-1996
| 镍铁铬钼铜低碳合金(UNS N08904)、镍铁铬钼铜氮低碳合金(UNS N08925,UNS N08031和UNS N08926)和铬镍铁氮低
| Specification for Ni-Fe-Cr-Mo-Cu Low-Carbon Alloy (UNS N08904) and Ni-Fe-Cr-Mo-Cu-N Low Carbon Alloys (UNS 08925, UNS N08031, and UNS N08925) Cr-Ni-Fe-N Low Carbon (UNS R20033)
|
| ANSI/ASTM D3228-2005
| 利用改良的凯氏(测定氮)法对润滑油和燃油中的总氮量进行测定的方法
| Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
|
| ANSI/ASTM D4629-2002
| 用注射/插入氧化燃烧和化学发光检测法测定液态石油烃中痕量氮的试验方法
| Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/inlet Oxidative Combustion and Chemiluminescence Detection
|
| ANSI/ASTM D5291-2002
| 石油产品和润滑剂中碳、氢和氮含量的仪器测定用试验方法
| Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
|
| ANSI/ASTM D5762-2005
| 用船进气化学发光法测定石油和石油产品中氮的试验方法
| Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-inlet Chemiluminescence
|
| ANSI/ASTM D982-2006
| 纸和纸板中有机氮试验方法
| Method of Test for Organic Nitrogen in Paper and Paperboard
|
| ANSI/ASTM F1685-2000
| 空气或氮气系统减压歧管规范
| Specification for Pressure-Reducing Manifolds for Air or Nitrogen Systems
|
| ANSI/ASTM F1791-2000
| 空气和氮气系统过滤器规范
| Specification for Filters Used in Air or Nitrogen Systems
|
| ANSI/ASTM F1793-1997
| 空气或氮气供应截流阀(亦称流量限制阀()规范
| Specification for Automatic Shut-Off Valves (also known as Excess Flow Valves EFV) for Air or Nitrogen Service
|
| ANSI/ASTM F1795-2000
| 空气或氮气系统减压阀规范
| Specification for Pressure-Reducing Valves for Air or Nitrogen Systems
|
| ANSI/ASTM F2189-2002
| 氮氧化物监测仪特殊要求规范
| Specification for Particular Requirements for Nitric Oxide Monitors
|
| ANSI/NFPA 42-1997
| 低氮硝化纤维素塑料的存储
| Pyroxylin Plastic, Storage of
|
| ANSI/NSF 245(i1)-2007
| 氮还原
| Nitrogen reduction
|
| ANSI/PIMA IT4.47-1998
| 摄影术(冲洗加工).废液.总氨态氮含量的测定.Kjeldahl微扩散法
| Photography (Processing) - Effluents - Determination of Total Amino Nitrogen - Microdiffusion Kjeldahl Method
|
| ANSI/PIMA IT4.48-1998
| 摄影术(冲洗加工).废液.氨型氮含量的测定.微扩散法
| Photography (Processing) - Effluents - Determination of Ammoniacal Nitrogen Content - Microdiffusion Method
|
| ASTM A 355-1989
| 掺氮用合金钢棒
| Standard Specification for Steel Bars, Alloys, for Nitriding
|
| ASTM B 649-2006
| 镍铁铬钼铜氮低碳合金(UNS N08925、UNS N08031、UNS N08354和UNS N08926)、铬镍铁氮低碳合金(UNS R20033)棒
| Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloys (UNS N08925, UNS N08031, UNS N08354, and UNS N08926), and Cr-Ni-Fe-N Low-Carbon Alloy (UNS R20033) Bar and Wire, and Ni-Cr-Fe-Mo-N Alloy (UNS N08936) Wire
|
| ASTM B 923-2002
| 用氦或氮比重瓶测定法测量金属粉末轮廓密度的标准试验方法
| Standard Test Method for Metal Powder Skeletal Density by Helium or Nitrogen Pycnometry
|
| ASTM C 1069-1986
| 用氮吸附法测定氧化铝和石英表面特性的试验方法
| Test Method for Specific Surface Area of Alumina or Quartz by Nitrogen Adsorption
|
| ASTM C 1494-2001
| 测定氮化硅粉末中碳、氮、氧的质量比值的标准试验方法
| Standard Test Methods for Determination of Mass Fraction of Carbon, Nitrogen, and Oxygen in Silicon Nitride Powder
|
| ASTM D 1426-2003
| 水中氨态氮的标准测试方法
| Standard Test Methods for Ammonia Nitrogen In Water
|
| ASTM D 1607-1991
| 大气中二氧化氮含量的测试方法(格里斯-沙耳茨曼反应)
| Test Method for Nitrogen Dioxide Content of the Atmosphere (Griess-Saltzman Reaction)
|
| ASTM D 1608-1998
| 气态燃烧产物中氮的氧化物的测试方法(苯酚二磺酸法)
| Standard Test Method for Oxides of Nitrogen in Gaseous Combustion Products (Phenol-Disulfonic Acid Procedures)
|
| ASTM D 1933-2003
| 作为电绝缘材料的氮气的标准规范
| Standard Specification for Nitrogen Gas as an Electrical Insulating Material
|
| ASTM D 1993-2003
| 用多点布-埃-特氮气吸附法对沉积二氧化硅表面面积的标准测试方法
| Standard Test Method for Precipitated Silica-Surface Area by Multipoint BET Nitrogen Adsorption
|
| ASTM D 2597-1994
| 含有二氧化氮和二氧化碳的馏除甲烷烃类液体混合物的气相色谱分析标准试验方法
| Standard Test Method for Analysis of Demethanized Hydrocarbon Liquid Mixtures Containing Nitrogen and Carbon Dioxide by Gas Chromatography
|
| ASTM D 2868-2007
| 皮革的氮含量(基尔达斯法)和皮革物质含量的标准试验方法
| Standard Test Method for Nitrogen Content (Kjeldahl) and Hide Substance Content of Leather
|
| ASTM D 2973-1971
| 泥炭材料中总氮的标准试验方法
| Standard Test Method for Total Nitrogen in Peat Materials
|
| ASTM D 3037-1993
| 炭黑的试验方法.用氮吸收法测定其表面积
| Test Methods for Carbon Black - Surface Area by Nitrogen Adsorption
|
| ASTM D 3179-2002
| 煤和焦炭分析样品中氮的标准测试方法
| Standard Test Methods for Nitrogen in the Analysis Sample of Coal and Coke
|
| ASTM D 3228-2005
| 用改进的克椰达方法测定润滑油及燃料油中总氮量的标准试验方法
| Standard Test Method for Total Nitrogen in Lubricating Oils and Fuel Oils by Modified Kjeldahl Method
|
| ASTM D 3590-2002
| 水中氮总数的基耶达尔标准试验方法
| Standard Test Methods for Total Kjeldahl Nitrogen in Water
|
| ASTM D 3608-1995
| 用griss-saltzman反应法测定大气中氧化氮(结合)含量的标准试验方法
| Standard Test Method for Nitrogen Oxides (Combined) Content in the Atmosphere by the Griess-Saltzman Reaction
|
| ASTM D 3824-1995
| 用化学发光法连续测定周围环境或工作场所空气中氮的氧化物含量的标准试验方法
| Standard Test Methods for Continuous Measurement of Oxides of Nitrogen in the Ambient or Workplace Atmosphere by the Chemiluminescent Method
|
| ASTM D 4222-2003
| 静态体积测量法测定催化剂氮吸附和解吸等温线的标准试验方法
| Standard Test Method for Determination of Nitrogen Adsorption and Desorption Isotherms of Catalysts By Static Volumetric Measurements
|
| ASTM D 4567-2003
| 连续流动法单点测定用氮吸附的催化剂和催化剂载体比表面积的标准试验方法
| Standard Test Method for Single-Point Determination of Specific Surface Area of Catalysts and Catalyst Carriers Using Nitrogen Adsorption by Continuous Flow Method
|
| ASTM D 4629-2002
| 注射/插入氧化燃料和化学发光法测定液态石油碳氢化合物中痕量有机结合物氮的标准试验方法
| Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection
|
| ASTM D 4641-1994
| 由氮解吸等温线计算催化剂孔隙尺寸分布的标准实施规程
| Standard Practice for Calculation of Pore Size Distributions of Catalysts from Nitrogen Desorption Isotherms
|
| ASTM D 4795-1994
| 可溶行硝化纤维素中氮含量的标准试验方法.交替法
| Standard Test Method for Nitrogen Content of Soluble Nitrocellulose - Alternative Method
|
| ASTM D 4954-1989
| 洗涤剂中测定次氮基三乙酸酯的试验方法
| Test Method for Determination of Nitrilotriacetates in Detergents
|
| ASTM D 5176-1991
| 用热解和化学发光检测法测定水中化学键合氮总量的标准试验方法
| Standard Test Method for Total Chemically Bound Nitrogen in Water by Pyrolysis and Chemiluminescence Detection
|
| ASTM D 5291-2002
| 仪器测定石油产品及润滑剂中碳、氢和氮含量的标准试验方法
| Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
|
| ASTM D 5373-2002
| 煤和焦碳的实验室样品中碳、氢和氮的仪器测定的试验方法
| Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Laboratory Samples of Coal and Coke
|
| ASTM D 5376-2006
| 橡胶合成材料的标准试验方法.橡胶抗氧化剂中基本氮含量的测定:聚合的四氢呋喃(TMQ)
| Standard Test Method for Rubber Compounding Materials - Determination of the Basic Nitrogen Content in Rubber Antioxidant: Polymerized TMQ
|
| ASTM D 5475-1993
| 用氮磷检测器通过气相色谱法测定水中含氮磷杀虫剂标准试验方法
| Standard Test Method for Nitrogen- and Phosphorus-Containing Pesticides in Water by Gas Chromatography with a Nitrogen-Phosphorus Detector
|
| ASTM D 5604-1996
| 沉淀二氧化硅的标准试验方法.用单点B.E.T.氮的吸附法沉淀的硅表面积
| Standard Test Methods for Precipitated Silica-Surface Area by Single Point B.E.T. Nitrogen Adsorption
|
| ASTM D 6016-2006
| 皮革中可萃取的氮和水的测定用标准试验方法
| Standard Test Method for Determination of Nitrogen, Water Extractable in Leather
|
| ASTM D 6069-2001
| 通过氧化燃烧和还原压力化学发光检测法测定航空用碳氢化合物中痕量氮的标准试验方法
| Standard Test Method for Trace Nitrogen in Aromatic Hydrocarbons by Oxidative Combustion and Reduced Pressure Chemiluminescence Detection
|
| ASTM D 6146-1997
| 检测分水界水溶氮的标准指南
| Standard Guide for Monitoring Aqueous Nutrients in Watersheds
|
| ASTM D 6187-1997
| 带有氮激光感应荧光的石油污染位点的锥形透度计技术特性的标准操作规程
| Standard Practice for Cone Penetrometer Technology Characterization of Petroleum Contaminated Sites with Nitrogen Laser-Induced Fluorescence
|
| ASTM D 6522-2000
| 用便携式分析仪测定燃天然气的往复式发动机、燃气轮机、燃烧炉和工艺加热器排放的氧化氮、一氧化碳和氧浓度
| Standard Test Method for Determination of Nitrogen Oxides, Carbon Monoxide, and Oxygen Concentrations in Emissions from Natural Gas-Fired Reciprocating Engines, Combustion Turbines, Boilers, and Process Heaters Using Portable Analyzers
|
| ASTM D 6979-2003
| 聚氨脂原材料的标准试验方法:可以表示为氮的百分量的多元醇中碱度的测定
| Standard Test Method for Polyurethane Raw Materials: Determination of Basicity in Polyols, Expressed as Percent Nitrogen
|
| ASTM D 7184-2007
| 用氧化燃烧和减压化学发光法测定芳烃中超低氮的标准试验方法
| Standard Test Method for Ultra Low Nitrogen in Aromatic Hydrocarbons by Oxidative Combustion and Reduced Pressure Chemiluminescence
|
| ASTM D 7323-2007
| IG-100(氮)的搬运、运输和储存用标准实施规程
| Standard Practice for Handling, Transportation, and Storage of IG-100 (Nitrogen)
|
| ASTM D 982-2005
| 纸和纸板中有机氮的标准试验方法
| Standard Test Method for Organic Nitrogen in Paper and Paperboard
|
| ASTM E 1019-2003
| 钢、铁、镍和钴合金中碳、硫、氮和氧含量测定的标准试验方法
| Standard Test Methods for Determination of Carbon, Sulfur, Nitrogen, and Oxygen in Steel and in Iron, Nickel, and Cobalt Alloys
|
| ASTM E 1140-1995
| 气相色谱法用氮/磷热离子电离探测器测试的标准实施规程
| Standard Practice for Testing Nitrogen/Phosphorus Thermionic Ionization Detectors for Use In Gas Chromatography
|
| ASTM E 1409-2005
| 用惰性气体熔解技术测定钛及钛合金中氧和氮的标准试验方法
| Standard Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique
|
| ASTM E 1436-1991
| 碳化硅晶须增强的氮化硅致密制品的搬运
| Handling Densified Articles of Silicon Nitride Reinforced with Silicon Carbide Whiskers
|
| ASTM E 147-1961
| 用基耶达法进行氮气微量测定用仪器
| Apparatus for Microdetermination of Nitrogen by Kjeldahl Method
|
| ASTM E 1566-2000
| 放在液氮中的危险生物材料搬运的标准指南
| Standard Guide for Handling Hazardous Biological Materials in Liquid Nitrogen
|
| ASTM E 2036-2007
| 用高效液相色谱法(HPLC)测定液态氯中三氯化氮的标准试验方法
| Standard Test Method for Nitrogen Trichloride in Liquid Chlorine by High Performance Liquid Chromatography (HPLC) |
| ASTM E 258-2007
| 用改进的基尔达斯(Kjeldahl)法测定有机材料中总氮含量的试验方法
| Standard Test Method for Total Nitrogen in Organic Materials by Modified Kjeldahl Method
|
| ASTM E 778-1987
| 回收废燃料的分析样品中氮的标准测试方法
| Standard Test Methods for Nitrogen in the Analysis Sample of Refuse-Derived Fuel
|
| ASTM F 1314-2007
| 外科植入物用锻造氮加强的22铬-13镍-5锰-2.5钼不锈钢棒材和线材用标准规范(UNS S20910)
| Standard Specification for Wrought Nitrogen Strengthened 22 Chromium - 13 Nickel - 5 Manganese - 2.5 Molybdenum Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S20910)
|
| ASTM F 1586-2002
| 外科植入物用锻制氮加强的21铬10镍3锰2.5钼不锈钢棒(UNS S31675)标准规范
| Standard Specification for Wrought Nitrogen Strengthened 21 Chromium - 10 Nickel - 3 Manganese - 2.5 Molybdenum Stainless Steel Bar for Surgical Implants (UNS S31675)
|
| ASTM F 1685-2000
| 空气或氮气系统用减压歧管的标准规范
| Standard Specification for Pressure-Reducing Manifolds for Air or Nitrogen Systems
|
| ASTM F 1791-2000
| 空气或氮气系统用过滤器的标准规范
| Standard Specification for Filters Used in Air or Nitrogen Systems
|
| ASTM F 1793-1997
| 空气或氮服务用自动截流阀(也称为溢流阀)的标准规范
| Standard Specification for Automatic Shut-Off Valves (Also Known as Excess Flow Valves, EFV) for Air Or Nitrogen Service
|
| ASTM F 1795-2000
| 空气或氮气系统用减压阀标准规范
| Standard Specification for Pressure-Reducing Valves for Air or Nitrogen Systems
|
| ASTM F 2094-2006
| 氮化硅轴承滚珠的标准规范
| Standard Specification for Silicon Nitride Bearing Balls
|
| ASTM F 2229-2007
| 外科植入物用锻制氮增强23锰-21铬-1钼低镍不锈钢合金棒材和线材的标准规范(UNS S29108)
| Standard Specification for Wrought, Nitrogen Strengthened 23Manganese-21Chromium-1Molybdenum Low-Nickel Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S29108)
|
| ASTM F 2581-2007
| 外科植入物用锻制氮增强的11锰-17铬-3钼低镍不锈钢合金棒材和金属丝的标准规范
| Standard Specification for Wrought Nitrogen Strengthened 11Manganese-17Chromium-3Molybdenum Low-Nickel Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S29225)
|
| 编号 | 中文名称 | 英文名称 |
|---|