| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| IEC 36C/172/DTS-2007 | IEC/TS 62371, Ed. 1.0:额定电压超过1000V的电气设备用空心压力和非压力陶瓷和玻璃绝缘子的特征 | IEC/TS 62371, Ed. 1.0: Characteristics of hollow pressurised and unpressurised ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1000 V |
| IEC 60141-4 AMD 1-1990 | 充油电缆和压气电缆及其附件的试验 第4部分:交流电压400kV及以下油浸纸绝缘高压力管式充油电缆及其附件 修 | Test on oil-filled and gas-pressure cables and their accessories; part 4: oil-impregnated paper-insulated high pressure oil-filled pipe-type cables and accessories for alternating voltages up to and including 400 kV; amendment 1 to IEC 60141-4:1980 |
| IEC 60141-4-1980 | 充油电缆和压气电缆及其附件的试验 第4部分:交流电压400kV及以下油浸纸绝缘高压力管式充油电缆及其附件 | Test on oil-filled and gas-pressure cables and their accessories. Part 4 : Oil-impregnated paper-insulated high pressure oil-filled pipe-type cables and accessories for alternating voltages up to and including 400 kV |
| IEC 60730-2-6-2007 | 家用和类似用途的自动电气控制器.第2-6部分:包括机械要求的自动电气压力敏感控制器的特殊要求 | Automatic electrical controls for household and similar use - Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements |
| IEC 60747-14-3-2001 | 半导体器件 第14-3部分：半导体敏感器 压力敏感器 | Semiconductor devices - Part 14-3: Semiconductor sensors; Pressure sensors |
| IEC 60811-3-1 AMD 1-1994 | 电缆绝缘和护套材料的通用试验方法 第3部分:聚氯乙稀(PVC)化合物专用方法 第1节:高温下压力试验 耐裂试验 | Common test methods for insulating and sheathing materials of electric cables - Part 3: Methods specific to PVC compounds - Section 1: Pressure test at high temperature - Tests for resistance to cracking; Amendment 1 |
| IEC 60811-3-1 AMD 2-2001 | 电缆绝缘和护套材料的通用试验方法 第3部分:聚氯乙烯(PVC)化合物专用方法 第1节:高温下压力试验 耐裂试 | Common test methods for insulating and sheathing materials of electric and optical cables - Part 3-1: Methods specific to PVC compounds - Pressure test at high temperature; Tests for resistance to cracking; Amendment 2 |
| IEC 60811-3-1 Corrigendum 1-1986 | 电缆绝缘和护套材料的通用试验方法.第3部分:聚氯乙烯(PVC)化合物专用方法.第1节:高温下压力试验.耐裂试验. | Common test methods for insulating and sheathing materials of electric cables - Part 3 : Methods specific to PVC compounds - Section 1: Pressure test at high temperature - Tests for resistance to cracking; Corrigendum 1 |
| IEC 60811-3-1-1985 | 电缆绝缘和护套材料的通用试验方法 第3部分:聚氯乙烯(PVC)化合物专用方法 第1节:高温下压力试验 耐裂试验 | Common test methods for insulating and sheathing materials of electric cables. Part 3 : Methods specific to PVC compounds. Section One : Pressure test at high temperature - Tests for resistance to cracking |
| IEC 61094-2-1992 | 测量传声器 第2部分:用互易对实验室标准传声器进行压力校准的基本方法 | Measurement microphones; part 2: primary method for pressure calibration of laboratory standard microphones by the reciprocity technique |
| IEC 61094-5-2001 | 测量传声器 第5部分：用比对对工作标准传声器的压力校准方法 | Measurement microphones - Part 5: Methods for pressure calibration of working standard microphones by comparison |
| IEC 61846-1998 | 声学 医用体外压力脉冲碎石机的声场特性和测量 | Acoustics - Characteristics and measurements of field of pressure pulse lithotripters |
| IEC/TR 61015-1990 | 电机用刷握 施加于电刷的静压力的测量指南 | Brush-holders for electrical machines; guide to the measurement of the static thrust applied to brushes |
| IEC/TR 62039-2007 | HV压力下户外使用的聚合物材料的选择指南 | Selection guide for polymeric materials for outdoor use under HV stress |
| ISO 10079-3-1999 | 医疗吸引设备 第3部分:真空或用压力驱动吸引设备 | Medical suction equipment - Part 3: Suction equipment powered from a vacuum or pressure source |
| ISO 10124-1994 | 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 层状缺陷检测用超声检验 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes - Ultrasonic testing for the detection of laminar imperfections |
| ISO 10332-1994 | 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 验证液压防泄漏用超声波检验 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes; ultrasonic testing for verification of hydraulic leak-tightness |
| ISO 10426-4-2004 | 石油和天然气工业.油井固井用水泥和材料.第4部分:在大气压力下泡沫水泥浆的制备和检验 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure |
| ISO 10426-5-2004 | 石油和天然气工业.油井固井用水泥和材料.第5部分:在大气压力下固井水泥加工制剂的收缩和膨胀的测定 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure |
| ISO 10467-2004 | 压力和无压力排水和排污塑料管道系统.基于不饱和聚酯树脂的玻璃增强热固性塑料(GRP)系统 | Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
| ISO 10501-1993 | 压力作用下液体输送用热塑性塑料管 压头损失的计算 | Thermoplastics pipes for the transport of liquids under pressure - Calculation of head losses |
| ISO 10502-1992 | 航空航天.温度为230℃及以下、压力为10500 kPa下使用的聚四氟乙烯(PTFE)软管组件.采购规范 | Aerospace; hose assemblies in polytetrafluoroethylene (PTFE) for use up to 232 °C and 10500 kPa; procurement specification |
| ISO 10524-1-2006 | 医用气体设备用的压力调节器.第1部分:压力调节器和带流量计的压力调节器 | Pressure regulators for use with medical gases - Part 1: Pressure regulators and pressure regulators with flow-metering devices |
| ISO 10524-2-2005 | 医用气体用压力调节器.第2部分:进气压力调节器和线性压力调节器 | Pressure regulators for use with medical gases - Part 2: Manifold and line pressure regulators |
| ISO 10524-3-2005 | 医用气体设备用的压力调节器.第3部分:带气瓶阀的压力调节器 | Pressure regulators for use with medical gases - Part 3: Pressure regulators integrated with cylinder valves |
| ISO 10543-1993 | 压力用无缝及热拉伸焊接钢管 全周边超声波厚度检测 | Seamless and hot-stretch-reduced welded steel tubes for pressure purposes; full peripheral ultrasonic thickness testing |
| ISO 10639-2004 | 压力和无压力给水塑料管道系统.基于不饱和聚酯树脂的玻璃增强热固性塑料(GRP)系统 | Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
| ISO 10763-1994 | 液压传动 端面平齐的无缝和焊接型精密钢管 尺寸及标称工作压力 | Hydraulic fluid power - Plain-end, seamless and welded precision steel tubes - Dimensions and nominal working pressures |
| ISO 10767-1-1996 | 液压传动 系统和元件产生压力波动值的测定 第1部分:用于泵的精密方法 | Hydraulic fluid power - Determination of pressure ripple levels generated in systems and components - Part 1: Precision method for pumps |
| ISO 10767-2-1999 | 液压传动 系统和元件产生压力波动值的测定 第2部分:用于泵的简化方法 | Hydraulic fluid power - Determination of pressure ripple levels generated in systems and components - Part 2: Simplified method for pumps |
| ISO 10767-3-1999 | 液压传动 系统和元件产生压力波动值的测定 第3部分:用于马达的方法 | Hydraulic fluid power - Determination of pressure ripple levels generated in systems and components - Part 3: Method for motors |
| ISO 10770-3-2007 | 液压传动.电调制液压控制阀.第3部分:压力控制阀的试验方法 | Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 3: Test methods for pressure control valves |
| ISO 10771-1-2002 | 液压传动.金属压力容器外层的压力疲劳试验.第1部分:试验方法 | Hydraulic fluid power - Fatigue pressure testing of metal pressure-containing envelopes - Part 1: Test method |
| ISO 11-1987 | 航空器 压力座舱的地面压力试验连接接头 | Aircraft; Ground pressure testing connections for pressure cabins |
| ISO 11242-1996 | 航空器 货运集装箱压力均衡要求 | Aircraft - Pressure equalization requirements for cargo containers |
| ISO 11484-1994 | 压力用途钢管 无损检验人员的资格及认证 | Steel tubes for pressure purposes - Qualification and certification of non-destructive testing (NDT) personnel |
| ISO 11496-1993 | 压力用途的承压无缝和焊接钢管 层间不完整性检查的管端超声波检测 | Seamless and welded steel tubes for pressure purposes; ultrasonic testing of tube ends for the detection of laminar imperfections |
| ISO 1167-1-2006 | 流体传输用热塑管、接头和组件.抗内压力的测定.第1部分:通用方法 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method |
| ISO 1167-2-2006 | 流体传输用热塑管、接头和组件.抗内压力的测定.第2部分:管试件的准备 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces |
| ISO 11673-2005 | 未增塑聚氯乙烯(PVC-U)压力管.断裂韧性测定 | Unplasticized poly(vinyl chloride) (PVC-U) pressure pipes - Determination of the fracture toughness properties |
| ISO 12048-1994 | 包装 满装的运输包装 使用压力试验机的压力试验和堆积试验 | Packaging - Complete, filled transport packages - Compression and stacking tests using a compression tester |
| ISO 12094-1994 | 压力用途的承压焊接钢管 焊接钢管用钢带/钢板分层缺陷检测用超声波试验 | Welded steel tubes for pressure purposes - Ultrasonic testing for the detection of laminar imperfections in strips/plates used in the manufacture of welded tubes |
| ISO 12095-1994 | 压力用途的承压无缝和焊接钢管 液体渗透试验 | Seamless and welded steel tubes for pressure purposes - Liquid penetrant testing |
| ISO 12096-1996 | 压力用途的承压埋弧焊接钢管 焊缝缺陷检测用X射线检查 | Submerged arc-welded steel tubes for pressure purposes - Radiographic testing of the weld seam for the detection of imperfections |
| ISO 12162-1995 | 压力用热塑性塑料管材和管件分级和命名 总体使用(设计)系数 | Thermoplastics materials for pipes and fittings for pressure applications - Classification and designation - Overall service (design) coefficient |
| ISO 12334-2000 | 航空航天 带压力补偿的变流量液压泵 35000 kPa系统的一般要求 | Aerospace - Hydraulic, pressure-compensated, variable delivery pumps - General requirements for 35000 kPa systems |
| ISO 13460-1998 | 农业灌溉设备 聚乙烯压力管用塑料支管架 | Agricultural irrigation equipment - Plastics saddles for polyethylene pressure pipes |
| ISO 13663-1995 | 压力用途的承压焊接钢管 焊缝周围分层缺陷检测用超声波试验 | Welded steel tubes for pressure purposes - Ultrasonic testing of the area adjacent to the weld seam for the detection of laminar imperfections |
| ISO 13664-1997 | 压力用途的承压无缝和焊接钢管 管端分层组织缺陷探测用磁粉检验 | Seamless and welded steel tubes for pressure purposes - Magnetic particle inspection of the tube ends for the detection of laminar imperfections |
| ISO 13665-1997 | 压力用途的承压无缝和焊接钢管 管身表面缺陷探测用磁粉检验 | Seamless and welded steel tubes for pressure purposes - Magnetic particle inspection of the tube body for the detection of surface imperfections |
| ISO 13760-1998 | 流体输送用塑料压力管材 Miner's规则 累积破坏的计算方法 | Plastics pipes for the conveyance of fluids under pressure - Miner's rule - Calculation method for cumulative damage |
| ISO 13761-1996 | 塑料管道和配件.使用温度在20℃以上的聚乙烯管道系统的压力折减系数 | Plastics pipes and fittings - Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 °C |
| ISO 13994-2005 | 防液体化学制品的防护服.防护服材料在压力下防液体渗透的测定 | Clothing for protection against liquid chemicals - Determination of the resistance of protective clothing materials to penetration by liquids under pressure |
| ISO 14236-2000 | 塑料管材和管件 给水系统聚乙烯压力管用压紧式机械连接件 | Plastics pipes and fittings - Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems |
| ISO 14317-2006 | 硬质合金除外的烧结金属材料.屈服压力强度的测定 | Sintered metal materials excluding hardmetals - Determination of compressive yield strength |
| ISO 14623-2003 | 航天系统.压力容器及承压结构.设计与操作 | Space systems - Pressure vessels and pressurized structures - Design and operation |
| ISO 15171-1-1999 | 用于流体传动和一般用途的管接头 诊断用液压管接头 第1部分:非压力下连接的管接头 | Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Part 1: Coupling not for connection under pressure |
| ISO 15171-2-2000 | 用于流体传动和一般用途的管接头 诊断用液压管接头 第2部分:带M16×2螺纹端的压力连接接头 | Connections for fluid power and general use - Hydraulic couplings for diagnostic purposes - Part 2: Coupling with M16 × 2 end for connection under pressure |
| ISO 15265-2004 | 热环境的人类工效学.热工作环境中压力或不适感预防的风险评估策略 | Ergonomics of the thermal environment - Risk assessment strategy for the prevention of stress or discomfort in thermal working conditions |
| ISO 15306-2003 | 玻璃增强热固性塑料管道.抗周期性内压力的测定 | Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the resistance to cyclic internal pressure |
| ISO 15364-2000 | 船舶与海上技术 散货船真空/压力阀 | Ships and marine technology - Pressure/vacuum valves for cargo tanks |
| ISO 15379-1-2004 | 铝生产用碳质材料.阴极块材料.第1部分:压力作用下由于钠渗透引起的膨胀的测定 | Carbonaceous materials for the production of aluminium - Cathode block materials - Part 1: Determination of the expansion due to sodium penetration with application of pressure |
| ISO 15379-2-2004 | 铝生产用碳质材料.阴极块材料.第2部分:无压力作用下由于钠渗透引起的膨胀的测定 | Carbonaceous materials for the production of aluminium - Cathode block materials - Part 2: Determination of the expansion due to sodium penetration without application of pressure |
| ISO 15500-8-2001 | 道路车辆 压缩天然气(CNG)燃料系统部件 第6部分:压力指示器 | Road vehicles - Compressed natural gas (CNG) fuel system components - Part 8: Pressure indicator |
| ISO 15616-3-2003 | 高质量焊接和切割用CO2激光射线机的验收试验.第3部分:气体流量和压力测量仪的校正 | Acceptance tests for CO<(Index)2>-laser beam machines for high quality welding and cutting - Part 3: Calibration of instruments for measurement of gas flow and pressure |
| ISO 15821-2007 | 门和窗.动态压力下不透水性试验.气旋方面 | Doorsets and windows - Water-tightness test under dynamic pressure - Cyclonic aspects |
| ISO 15996-2005 | 储气瓶.剩余压力阀.一般要求和型式试验 | Gas cylinders - Residual pressure valves - General requirements and type testing |
| ISO 16028 AMD 1-2006 | 液压传动.在20MPa(200巴)至31.5MPa(315巴)压力下使用的平面对接型快速接头.规范.修改件1 | Hydraulic fluid power - Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) - Specifications; Amendment 1 |
| ISO 16028-1999 | 液压传动 用于压力为20 MPa(200 bar)～31.5 MPa(315 bar)的平面对接型快速接头 规范 | Hydraulic fluid power - Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) - Specifications |
| ISO 1607-2-1989 | 容积真空泵 性能测量方法 第2部分:极限压力的测量 | Positive-displacement vacuum pumps; measurement of performance characteristics; part 2: measurement of ultimate pressure |
| ISO 1608-2-1989 | 蒸气真空泵 性能特性的测量 第2部分:临界前级压力的测量 | Vapour vacuum pumps; measurement of performance characteristics; part 2: measurement of critical backing pressure |
| ISO 161-1-1996 | 流体输送用热塑性塑料管材 公称外径和公称压力 第1部分:公制系列 | Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Part 1: Metric series |
| ISO 161-2-1996 | 流体输送用热塑性塑料管材 公称外径和公称压力 第2部分:英制系列 | Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Part 2: Inch-based series |
| ISO 16232-3-2007 | 道路车辆.液压管路部件清洁度.第3部分:压力漂洗萃取污染物的方法 | Road vehicles - Cleanliness of components of fluid circuits - Part 3: Method of extraction of contaminants by pressure rinsing |
| ISO 16422-2006 | 由定向未增塑聚(氯)乙烯(PVC-O)制成的用于压力下水运输的管道和接头.规范 | Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure - Specifications |
| ISO 16528-1-2007 | 锅炉和压力容器.第1部分:性能要求 | Boilers and pressure vessels - Part 1: Performance requirements |
| ISO 16528-2-2007 | 锅炉和压力容器.第2部分:ISO 16528-1的要求履行规程 | Boilers and pressure vessels - Part 2: Procedures for fulfilling the requirements of ISO 16528-1 |
| ISO 16873 AMD 1-2005 | 液压传动.压力开关.安装表面.修改件1 | Hydraulic fluid power - Pressure switches - Mounting surfaces; Amendment 1 |
| ISO 16873-2002 | 液压传动.压力开关.安装表面 | Hydraulic fluid power - Pressure switches - Mounting surfaces |
| ISO 17190-7-2001 | 尿失禁用吸尿器 聚合基吸收材料特性化的试验方法 第7部分：比重法测定压力下的吸收 | Urine-absorbing aids for incontinence - Test methods for characterizing polymer-based absorbent materials - Part 7: Gravimetric determination of absorption under pressure |
| ISO 17230-2006 | 皮革.物理和机械试验.水渗透压力测定 | Leather - Physical and mechanical tests - Determination of water penetration pressure |
| ISO 17484-1-2006 | 塑料管道系统.最大工作压力≥500 kPa的室内燃气设备用多层管道系统.第1部分:系统规范 | Plastics piping systems - Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) - Part 1: Specifications for systems |
| ISO 17654-2003 | 金属材料焊接的破坏检验.电阻焊接.电阻缝焊的压力试验 | Destructive tests on welds in metallic materials - Resistance welding - Pressure test on resistance seam welds |
| ISO 17744-2004 | 塑料.作为温度和压力函数的比容的测定(pvT图).活塞装置法 | Plastics - Determination of specific volume as a function of temperature and pressure (pvT diagram) - Piston apparatus method |
| ISO 18172-1-2007 | 储气瓶.可再灌装的焊接不锈钢气瓶.第1部分:试验压力≤6MPa | Gas cylinders - Refillable welded stainless steel cylinders - Part 1: Test pressure 6 MPa and below |
| ISO 18172-2-2007 | 储气瓶.可再灌装的焊接不锈钢气瓶.第2部分:试验压力大于6MPa | Gas cylinders - Refillable welded stainless steel cylinders - Part 2: Test pressure greater than 6 MPa |
| ISO 18752-2006 | 橡胶软管和软管组件.金属丝或纺织物.水利用的单胎压力加强型.规范 | Rubber hoses and hose assemblies - Wire- or textile-reinforced single-pressure types for hydraulic applications - Specification |
| ISO 19973-4-2007 | 气压传动.通过测试评定元件的可靠度.第4部分:压力调节器 | Pneumatic fluid power - Assessment of component reliability by testing - Part 4: Pressure regulators |
| ISO 2035-1974 | 压力下使用的弹性密封圈式连接的硬聚氯乙烯(PVC)注塑管件 耐压试验 | Unplasticized polyvinyl chloride (PVC) moulded fittings for elastic sealing ring type joints for use under pressure; Pressure-resistance test |
| ISO 2044-1974 | 压力管用注塑溶剂粘接的硬聚氯乙烯(PVC)承口管件 内水压试验 | Unplasticized polyvinyl chloride (PVC) injection-moulded solvent-welded socket fittings for use with pressure pipe; Hydraulic internal pressure test |
| ISO 2045-1988 | 弹性密封环型连接的硬聚氯乙烯(PVC-U)和氯化聚氯乙烯(PVC-C)压力管的单承口 最小配合深度 | Single sockets for unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) pressure pipes with elastic sealing ring type joints; minimum depths of engagement |
| ISO 2048-1990 | 弹性密封圈型接头的硬聚氯乙烯(PVC-U)压力管的双承口 最小配合深度 | Double-socket fittings for unplasticized poly(vinyl chloride) (PVC-U) pressure pipes with elastic sealing ring type joints; minimum depths of engagement |
| ISO 20623-2003 | 石油及相关产品.用4球法测定流体的极限压力和耐磨性(欧洲条件) | Petroleum and related products - Determination of the extreme-pressure and anti-wear properties of fluids - Four ball method (European conditions) |
| ISO 21750-2006 | 道路车辆.有关增进轮胎充气压力监控的安全 | Road vehicles - Safety enhancement in conjunction with tyre inflation pressure monitoring |
| ISO 2186-2007 | 封闭管道中的流体流量.一次和二次元件间压力信号传送的连接件 | Fluid flow in closed conduits - Connections for pressure signal transmissions between primary and secondary elements |
| ISO 22435-2007 | 储气瓶.带压力调节器的气缸阀.规范和类型测试 | Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing |
| ISO 23251 Technical Corrigendum 1-2007 | 石油、石化和天然气工业.压力释放和降压系统.技术勘误1 | Petroleum, petrochemical and natural gas industries - Pressure-relieving and depressuring systems; Technical Corrigendum 1 |
| ISO 23251-2006 | 石油、石化和天然气工业.压力.缓解和减少系统 | Petroleum, petrochemical and natural gas industries - Pressure-relieving and depressuring systems |
| ISO 23551-2-2006 | 气体燃烧器和燃气设备用安全和控制装置.特殊要求.第2部分:压力调节器 | Safety and control devices for gas burners and gas-burning appliances - Particular requirements - Part 2: Pressure regulators |
| ISO 2536-1974 | 公制系列、硬聚氯乙烯(PVC)压力管材和管件 法兰尺寸 | Unplasticized polyvinyl chloride (PVC) pressure pipes and fittings, metric series; Dimensions of flanges |
| ISO 2556-1974 | 塑料 在大气压力下薄膜和薄板的透气率的测定 测压法 | Plastics; Determination of the gas transmission rate of films and thin sheets under atmospheric pressure; Manometric method |
| ISO 2605-3-1985 | 压力用途的钢 高温特性的推导和验证 第3部分:在限定数据时,推导高温屈服应力或弹性极限应力特性可供选择的 | Steel products for pressure purposes; Derivation and verification of elevated temperature properties; Part 3 : An alternative procedure for deriving the elevated temperature yield or proof stress properties when data are limited |
| ISO 294-1 AMD 2-2005 | 塑料.热塑性材料试样的注模塑法.第1部分:一般原则、多用途模塑件及条形试样.修改件2:吸着压力和时间的测定 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens; Amendment 2: Methods of determining the hold pressure and hold time |
| ISO 2944-2000 | 流体传动系统和元件 公称压力 | Fluid power systems and components - Nominal pressures |
| ISO 3458-1976 | 聚乙烯(PE)压力管材和管件间的装配接头 内压密封试验 | Assembled joints between fittings and polyethylene (PE) pressure pipes ; Test of leakproofness under internal pressure |
| ISO 3459-1976 | 聚乙烯(PE)压力管 用机械式管件装配的接头 内压试验法和要求 | Polyethylene (PE) pressure pipes; Joints assembled with mechanical fittings; Internal under-pressure test method and requirement |
| ISO 3460-1975 | 硬聚氯乙烯(PVC)压力管材 公制系列 凹法兰管接头尺寸 | Unplasticized polyvinyl chloride (PVC) pressures pipes; Metric series; Dimensions of adapter for backing flange |
| ISO 3501-1976 | 聚乙烯(PE)压力管材和管件间的装配接头 抗拉拔试验 | Assembled joints between fittings and polyethylene (PE) pressure pipes; Test of resistance to pull out |
| ISO 3503-1976 | 聚乙烯(PE)压力管材和管件间的装配接头 弯曲时承受内压的密封试验 | Assembled joints between fittings and polyethylene (PE) pressure pipes; Test of leakproofness under internal pressure when subjected to bending |
| ISO 3583-1984 | 道路车辆 气压制动装置的压力试验连接 | Road vehicles; Pressure test connection for compressed-air pneumatic braking equipment |
| ISO 3603-1977 | 弹性密封圈式硬聚氯乙烯(PVC)压力管件 密封压力试验 | Fittings for unplasticized polyvinyl chloride (PVC) pressure pipes with elastic sealing ring type joints; Pressure test for leakproofness |
| ISO 3604-1976 | 弹性密封圈式硬聚氯乙烯(PVC)压力管件 外水压条件下的密封压力试验 | Fittings for unplasticized polyvinyl chloride (PVC) pressure pipes with elastic sealing ring type joints; Pressure test for leakproofness under conditions of external hydraulic pressure |
| ISO 3663-1976 | 聚乙烯(PE)压力管材和管件 公制系列 法兰尺寸 | Polyethylene (PE) pressure pipes and fittings, metric series; Dimensions of flanges |
| ISO 3935-1977 | 造船 内河航行 消防水系统 压力 | Shipbuilding; Inland navigation; Fire-fighting water system; Pressures |
| ISO 3948-1977 | 造船 内河船舶 压缩空气系统 压力等级 | Shipbuilding; Inland vessels; Compressed-air systems; Pressure ranges |
| ISO 3993-1984 | 液化石油气和轻质烃类 密度或相对密度的测定 压力比重计法 | Liquefied petroleum gas and light hydrocarbons; Determination of density or relative density; Pressure hydrometer method |
| ISO 4153-1981 | 航空器 压力燃油的分配系统 关闭脉动压力的试验程序和极限值 | Aircraft; Pressure fuel dispensing system; Test procedure and limit value for shut-off surge pressure |
| ISO 4174-1998 | 谷物、油籽和豆类 单维气流通过粮堆的单位压力损失的测量 | Cereals, oilseeds and pulses - Measurement of unit pressure loss in one-dimensional air flow through bulk grain |
| ISO 4179-2005 | 压力和非压力管道用球墨铸铁管和配件.水泥灰浆内衬 | Ductile iron pipes and fittings for pressure and non-pressure pipelines - Cement mortar lining |
| ISO 4392-1-2002 | 液压传动.马达特性的测定.第1部分:在恒低速和恒压力下的测定 | Hydraulic fluid power - Determination of characteristics of motors - Part 1: At constant low speed and constant pressure |
| ISO 4399-1995 | 流体传动系统和元件 管接头及其附件 公称压力系列 | Fluid power systems and components - Connectors and associated components - Nominal pressures |
| ISO 45-1990 | 航空器 压力加油接头 | Aircraft; pressure refuelling connections |
| ISO 4548-6 Technical Corrigendum 1-1990 | 内燃机全流式机油滤清器试验方法 第6部分:静态爆破压力试验 技术勘误1 | Methods of test for full-flow lubricating oil filters for internal combustion engines; part 6: static burst pressure test; technical corrigendum 1 |
| ISO 4548-6-1985 | 内燃机全流式机油滤清器试验方法 第6部分:静态爆破压力试验 | Methods of test for full-flow lubricating oil filters for internal combustion engines; Part 6 : Static burst pressure test |
| ISO 4622-1992 | 色漆和清漆 堆积压力试验 | Paints and varnishes; pressure test for stackability |
| ISO 4666-4-2007 | 硫化橡胶.挠曲计测试中温升和抗疲劳性测定.第4部分:恒定压力挠曲计 | Rubber, vulcanized - Determination of temperature rise and resistance to fatigue in flexometer testing - Part 4: Constant-stress flexometer |
| ISO 4783-3-1981 | 工业用金属丝筛网和金属丝编织网 网孔尺寸和金属丝直径组合选择指南 第3部分:预弯成形或压力焊的金属丝网的 | Industrial wire screens and woven wire cloth; Guide to the choice of aperture size and wire diameter combinations; Part 3 : Preferred combinations for pre-crimped or pressure-welded wire screens |
| ISO 485-1973 | 航空器的水-甲醇压力加注接头 | Aircraft water-methanol pressure connections |
| ISO 4991-2005 | 压力用途的钢铸件 | Steel castings for pressure purposes |
| ISO 5171-1995 | 焊接、切割及相关工艺用压力表 | Pressure gauges used in welding, cutting and allied processes |
| ISO 5208-1993 | 通用阀门 阀门的压力试验 | Industrial valves; pressure testing of valves |
| ISO 5596-1999 | 液压传动 隔离式充气蓄能器 压力、容积范围和特性量 | Hydraulic fluid power - Gas-loaded accumulators with separator - Ranges of pressures and volumes and characteristic quantities |
| ISO 5781-2000 | 液压传动 压力控制阀(不包括溢流阀)、顺序阀、卸荷阀、节流阀和单向阀 安装面 | Hydraulic fluid power - Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces |
| ISO 6150-1988 | 气压传动 最高工作压力为10 bar、16 bar和25 bar(1 MPa、1.6 MPa和2.5 MPa)圆柱形快换接头、插头、连接尺寸 | Pneumatic fluid power; cylindrical quick-action couplings for maximum working pressures of 10 bar, 16 bar and 25 bar (1 MPa, 1,6 MPa and 2,5 MPa); plug connecting dimensions, specifications, application guidelines and testing |
| ISO 6162-1 Technical Corrigendum 1-2004 | 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘连接器.第1部分:3.5MPa至35MPa(35巴至350巴)压力下 | Hydraulic fluid power - Flange connectors with split or one-piece flange clamps and metric or inch screws - Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127; Technical Corrigendum 1 |
| ISO 6162-1-2002 | 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘连接器.第1部分:压力为3.5MPa至35MPa(35巴至350巴) | Hydraulic fluid power - Flange connectors with split or one-piece flange clamps and metric or inch screws - Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 |
| ISO 6162-2-2002 | 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘连接器.第2部分:压力为35MPa至40MPa(350巴至400巴) | Hydraulic fluid power - Flange connectors with split or one-piece flange champs and metric or inch screws - Part 2: Flange connectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar), DN 13 to DN 51 |
| ISO 6164-1994 | 液压传动.25MPa和40MPa(250 bar和400 bar)压力下使用的四螺栓整体方法兰 | Hydraulic fluid power; four-srew, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar) |
| ISO 6303-1981 | 不包括ISO 2604第1～6部分的压力容器钢 长期受力断裂性能的推导 | Pressure vessel steels not included in ISO 2604, Parts 1 to 6; Derivation of long-time stress rupture properties |
| ISO 6403-1988 | 液压传动 控制流量及压力的阀 试验方法 | Hydraulic fluid power; valves controlling flow and pressure; test methods |
| ISO 6771-2007 | 航空航天.流体系统和部件.压力和温度分类 | Aerospace - Fluid systems and components - Pressure and temperature classifications |
| ISO 6822-1984 | 马铃薯、根类蔬菜和结球甘蓝 在地下仓库中用压力通风的贮存指南 | Potatoes, root vegetables and round-headed cabbages; Guide to storage in silos using forced ventilation |
| ISO 683-10-1987 | 热处理钢、合金钢和易切钢 第10部分:压力加工渗氮钢 | Heat-treatable steels, alloy steels and free-cutting steels; Part 10 : Wrought nitriding steels |
| ISO 683-11-1987 | 热处理钢、合金钢和易切钢 第11部分:压力加工表面硬化钢 | Heat-treatable steels, alloy steels and free-cutting steels; Part 11 : Wrought case-hardening steels |
| ISO 6898-1984 | 开式机械压力机 性能及尺寸 | Open front mechanical power presses; Capacity ratings and dimensions |
| ISO 6899-1984 | 开式机械动力压力机验收条件 精度检验 | Acceptance conditions of open front mechanical power presses; Testing of the accuracy |
| ISO 6993-1-2006 | 输送气体燃料用埋设的、高耐冲击的聚氯乙烯(PVC-HI)管道.第1部分:最大操作压力为1巴(100 kPa)的管子 | Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 1: Pipes for a maximum operating pressure of 1 bar (100 kPa) |
| ISO 6993-2-2006 | 输送气体燃料用埋设的、高耐冲击的聚氯乙烯(PVC-HI)管道.第2部分:最大操作压力为200mbar(20 kPa)的管件 | Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 2: Fittings for a maximum operating pressure of 200 mbar (20 kPa) |
| ISO 6993-3-2006 | 输送气体燃料用埋设的、高耐冲击的聚氯乙烯(PVC-HI)管道.第3部分:最大操作压力为1巴(100 kPa)的管件和鞍座 | Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 3: Fittings and saddles for a maximum operating pressure of 1 bar (100 kPa) |
| ISO 7-1 Technical Corrigendum 1-2007 | 螺纹上有压力密封接缝的管螺纹.第1部分:尺寸、公差和标志.技术勘误1 | Pipe threads where pressure-tight joints are made on the threads - Part 1: Dimensions, tolerances and designation; Technical Corrigendum 1 |
| ISO 7169-2007 | 航空航天.液压系统用24°锥形的、压力范围截至3000psi或21000kPa的可拆卸管接头.采购规范(英制/米制) | Aerospace - Separable tube fittings for fluid systems, for 24° cones, for pressures up to 3000 psi or 21000 kPa - Procurement specification, inch/metric |
| ISO 7268 AMD 1-1984 | 管道元件 公称压力的定义 修改1 | Amendment 1-1984 |
| ISO 7268-1983 | 管道元件 公称压力的定义 | Pipe components; Definition of nominal pressure |
| ISO 727-1-2002 | 压力管件用由未增塑的聚氯乙烯,氯化聚氯乙烯或丙烯腈/丁二烯/苯乙烯制的带普通管套的管配件.第1部分:米制系 | Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure - Part 1: Metric series |
| ISO 727-2-2005 | 压力管件用由未增塑聚氯乙烯、氯化聚氯乙烯或丙烯腈/丁二烯/苯乙烯制的带普通管套的管配件.第2部分:英制系 | Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure - Part 2: Inch-based series |
| ISO 7291-1999 | 气焊设备 用于300 bar以下的焊接、切割及相关工艺用汇流系统上的压力调节器 | Gas welding equipment - Pressure regulators for manifold systems used in welding, cutting and allied processes up to 300 bar |
| ISO 7458-2004 | 玻璃容器.耐内压力.试验方法 | Glass containers - Internal pressure resistance - Test methods |
| ISO 7509-2000 | 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材 持续内压力下破坏时间的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of time to failure under sustained internal pressure |
| ISO 7751-1991 | 橡胶和塑料软管和软管组件 试验压力和爆破压力对设计工作压力的比值 | Rubber and plastics hoses and hose assemblies; ratios of proof and burst pressure to design working pressure |
| ISO 8169-1984 | 作物保护设备 喷雾器 喷嘴和压力计的连接尺寸 | Equipment for crop protection; Sprayers; Connecting dimensions for nozzles and manometers |
| ISO 8278-1986 | 航空航天 液压式压力补偿变流量泵 一般要求 | Aerospace; Hydraulic, pressure compensated, variable delivery pumps; General requirements |
| ISO 8502-3-1992 | 涂装油漆和有关产品前钢材预处理 表面清洁度的评定试验 第3部分:油漆前预处理后的钢材表面上的灰尘评定(压 | Preparation of steel substrates before application of paint and related products; tests for the assessment of surface cleanliness; part 3: assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method) |
| ISO 8536-10-2004 | 医用输液器具.第10部分:与压力输液仪一起使用的流体线路附件 | Infusion equipment for medical use - Part 10: Accessories for fluid lines for use with pressure infusion equipment |
| ISO 8536-11-2004 | 医用输液器具.第11部分:与压力输液仪一起使用的输液过滤器 | Infusion equipment for medical use - Part 11: Infusion filters for use with pressure infusion equipment |
| ISO 8536-8-2004 | 医用输液器具.第8部分:有压力输液仪的输液器具 | Infusion equipment for medical use - Part 8: Infusion equipment for use with pressure infusion apparatus |
| ISO 8536-9-2004 | 医用输液器具.第9部分:与压力输液仪一起使用的流体线路 | Infusion equipment for medical use - Part 9: Fluid lines for use with pressure infusion equipment |
| ISO 8540-1993 | 开式机械压力机 词汇 两种语言版 | Open front mechanical power presses; vocabulary |
| ISO 8572-1991 | 玻璃纤维增强热塑性塑料管材和管件 与压力有关的定义,包括它们之间关系,以及安装和连接的术语 | Pipes and fittings made of glass-reinforced thermosetting plastics (GRP); definitions of terms relating to pressure, including relationships between them, and terms for installation and jointing |
| ISO 8625-1-1993 | 航空航天 流体系统 词汇 第1部分:与压力有关的通用术语和定义 两种语言版 | Aerospace; fluid systems; vocabulary; part 1: general terms and definitions relating to pressure |
| ISO 8756-1994 | 空气质量 温度、压力和湿度的数据处理 | Air quality; handling of temperature, pressure and humidity data |
| ISO 8773-2006 | 无压力地下排水和排污塑料管道系统.聚丙烯(PP) | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) |
| ISO 9110-2-1990 | 液压传动 测量技术 第2部分:密闭回路中平均稳定压力的测量 | Hydraulic fluid power; measurement techniques; part 2: measurement of average steady-state pressure in a closed conduit |
| ISO 9188-1993 | 机床 公称力从400 kN到4000 kN(含4000 kN)单动机械式矫直压力机 特性和尺寸 | Machine tools; straight-sided single-action mechanical power presses from 400 kN up to and including 4000 kN nominal force; characteristics and dimensions |
| ISO 9189-1993 | 机床 公称力从250 kN到4000 kN(含4000 kN)单动高速机械式矫直压力机 特性和尺寸 | Machine tools; straight-sided high-speed mechanical power presses from 250 kN up to and including 4000 kN nominal force; characteristics and dimensions |
| ISO 9302-1994 | 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 液压密封验证电磁试验法 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes; electromagnetic testing for verification of hydraulic leak-tightness |
| ISO 9303-1989 | 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 检测纵向缺陷用全周边超声波试验 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes; full peripheral ultrasonic testing for the detection of longitudinal imperfections |
| ISO 9304-1989 | 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 检测缺陷用涡流电流试验 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes; eddy current testing for the detection of imperfections |
| ISO 9305-1989 | 压力用途的无缝钢管 横向缺陷全周边超声电流检验 | Seamless steel tubes for pressure purposes; full peripheral ultrasonic testing for the detection of transverse imperfections |
| ISO 9311-3-2005 | 热塑性管道系统用胶粘剂.第3部分:测定耐内压力性的试验方法 | Adhesives for thermoplastic piping systems - Part 3: Test method for the determination of resistance to internal pressure |
| ISO 9327-1-1999 | 压力用途的钢锻件和轧制或锻造的棒材 交货技术条件 第1部分:一般要求 | Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions - Part 1: General requirements |
| ISO 9327-2-1999 | 压力用途的钢锻件和轧制或锻造的棒材 交货技术条件 第2部分:具有规定的高温度特性的非合金和合金钢(钼、镉 | Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy (Mo, Cr and CrMo) steels with specified elevated temperature properties |
| ISO 9327-3-1999 | 压力用途的钢锻件和轧制或锻造的棒材 交货技术条件 第3部分:具有规定的低温度特性的镍钢 | Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions - Part 3: Nickel steels with specified low temperature properties |
| ISO 9327-4-1999 | 压力用途的钢锻件和轧制或锻造的棒材 交货技术条件 第4部分:高强度可焊接细粒钢 | Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions - Part 4: Weldable fine grain steels with high proof strength |
| ISO 9327-5-1999 | 压力用途的钢锻件和轧制或锻造的棒材 交货技术条件 第5部分:不锈钢 | Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions - Part 5: Stainless steels |
| ISO 9328-1-2003 | 压力用途的扁钢产品.交货技术条件.第1部分:一般要求 | Steel flat products for pressure purposes - Technical delivery conditions - Part 1: General requirements |
| ISO 9328-2-2004 | 压力用途的扁钢制品.交货技术条件.第2部分:规定了高温性能的非合金和合金钢 | Steel flat products for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| ISO 9328-3-2004 | 压力用途扁钢产品.交货技术条件.第3部分:正火可焊细粒钢 | Steel flat products for pressure purposes - Technical delivery conditions - Part 3: Weldable fine grain steels, normalized |
| ISO 9328-4-2004 | 压力用途扁钢产品.交货技术条件.第4部分:规定了低温性能的镍合金钢 | Steel flat products for pressure purposes - Technical delivery conditions - Part 4: Nickel-alloy steels with specified low temperature properties |
| ISO 9328-5-2004 | 压力用途扁钢产品.交货技术条件.第5部分:热机辊轧可焊细粒钢 | Steel flat products for pressure purposes - Technical delivery conditions - Part 5: Weldable fine grain steels, thermomechanically rolled |
| ISO 9328-6-2004 | 压力用途扁钢产品.交货技术条件.第6部分:淬火和回火的可焊接细粒钢 | Steel flat products for pressure purposes - Technical delivery conditions - Part 6: Weldable fine grain steels, quenched and tempered |
| ISO 9328-7-2004 | 压力用途扁钢产品.交货技术条件.第7部分:不锈钢 | Steel flat products for pressure purposes - Technical delivery conditions - Part 7: Stainless steels |
| ISO 9329-1-1989 | 压力用途的无缝钢管 交货技术条件 第1部分:规定室温性能的非合金钢 | Seamless steel tubes for pressure purposes; technical delivery conditions; part 1: unalloyed steels with specified room temperature properties |
| ISO 9329-2-1997 | 压力用途的无缝钢管 交货技术条件 第2部分:规定高温性能的非合金钢和合金钢 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Unalloyed and alloyed steels with specified elevated temperature properties |
| ISO 9329-3-1997 | 压力用途的无缝钢管 交货技术条件 第3部分:规定低温性能的非合金钢和合金钢 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Unalloyed and alloyed steels with specified low temperature properties |
| ISO 9329-4-1997 | 压力用途的无缝钢管 交货技术条件 第4部分:奥氏体不锈钢 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 4: Austenitic stainless steels |
| ISO 9330-1-1990 | 压力用途的焊接钢管 交货技术条件 第1部分:规定室温性能的非合金钢管 | Welded steel tubes for pressure purposes; technical delivery conditions; part 1: unalloyed steel tubes with specified room temperatures properties |
| ISO 9330-2-1997 | 压力用途的焊接钢管 交货技术条件 第2部分:规定高温性能的电阻焊接和感应焊接非合金钢管和合金钢管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 2: Electric resistance and induction welded unalloyed and alloyed steel tubes with specified elevated temperature properties |
| ISO 9330-3-1997 | 压力用途的焊接钢管 交货技术条件 第3部分:规定低温性能的电阻焊接和感应焊接非合金钢管和合金钢管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Electric resistance and induction welded unalloyed and alloyed steel tubes with specified low temperature properties |
| ISO 9330-4-2000 | 压力用途的焊接钢管 交货技术条件 第4部分:规定高温性能的埋弧焊接非合金钢管和合金钢管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 4: Submerged arc-welded unalloyed and alloyed steel tubes with specified elevated temperature properties |
| ISO 9330-5-2000 | 压力用途的焊接钢管 交货技术条件 第5部分:规定低温性能的埋弧焊接非合金钢管和合金钢管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 5: Submerged arc-welded unalloyed and alloyed steel tubes with specified low temperature properties |
| ISO 9330-6-1997 | 压力用途的焊接钢管 交货技术条件 第6部分:奥氏体不锈钢管的焊接长度 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Longitudinally welded austenitic stainless steel tubes |
| ISO 9393-1-2004 | 工业用热塑性阀门.压力试验方法和要求.第1部分:总则 | Thermoplastics valves for industrial applications - Pressure test methods and requirements - Part 1: General |
| ISO 9393-2-2005 | 工业用热塑性阀门.压力试验方法和要求.第2部分:试验条件和基本要求 | Thermoplastics valves for industrial applications - Pressure test methods and requirements - Part 2: Test conditions and basic requirements |
| ISO 9402-1989 | 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 检测纵向缺陷用铁磁钢管全周边磁转换/磁链试验 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes; full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of longitudinal imperfections |
| ISO 9457-2-1994 | 道路车辆.米制起动电机小齿轮.第2部分:具有20度压力角的小齿轮 | Road vehicles - Metric starter motor pinions - Part 2: Pinions with 20° pressure angle |
| ISO 9598-1989 | 压力用途的无缝钢管 检测横向缺陷用铁磁钢管全周边磁转换/磁链试验 | Seamless steel tubes for pressure purposes; full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of transverse imperfections |
| ISO 9623-1997 | 压力流体用聚乙烯(PE)/金属和聚丙烯(PP)/金属接头管件 螺纹的设计长度和尺寸 公制系列 | PE/metal and PP/metal adaptor fittings for pipes for fluids under pressure - Design lengths and size of threads - Metric series |
| ISO 9624-1997 | 压力流体用热塑性塑料管材 法兰接头和活套法兰的适配尺寸 | Thermoplastics pipes for fluids under pressure - Mating dimensions of flange adapters and loose backing flanges |
| ISO 9625-1993 | 灌溉用聚乙烯压力管的机械式连接管件 | Mechanical joint fittings for use with polyethylene pressure pipes for irrigation purposes |
| ISO 9644 AMD 1-1998 | 农业灌溉设备 灌溉阀压力损失 试验方法 修改1 | Agricultural irrigation equipment - Pressure losses in irrigation valves - Test method; Amendment 1 |
| ISO 9644-1993 | 农业灌溉设备 灌溉阀压力损失 试验方法 | Agricultural irrigation equipment; pressure losses in irrigation valves; test method |
| ISO 9662-1994 | 航空器设备 机载设备的环境和工作条件 湿度、温度和压力试验 | Aircraft equipment; environmental and operating conditions for airborne equipment; humidity, temperature and pressure tests |
| ISO 9764-1989 | 压力用途的电阻焊和感应焊钢管 焊缝的纵向缺陷超声波检验 | Electric resistance and induction welded steel tubes for pressure purposes; ultrasonic testing of the weld seam for the detection of longitudinal imperfections |
| ISO 9765-1990 | 压力用途的埋弧焊钢管 焊缝的纵向和/或横向缺陷超声波检测 | Submerged arc-welded steel tubes for pressure purposes; ultrasonic testing of the weld seam for the detection of longitudinal and/or transverse imperfections |
| ISO 9853-1991 | 压力管道系统用硬聚氯乙烯(PVC-U)管件 扁平试验 | Injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings for pressure pipe systems; crushing test |
| ISO 9863-1-2005 | 土工织物.规定压力下厚度的测定.第1部分:单层 | Geosynthetics - Determination of thickness at specified pressures - Part 1: Single layers |
| ISO 9863-2-1996 | 土工布及相关产品 特定压力下厚度的测定 第2部分:多层制品中单层厚度测定程序 | Geotextiles and geotextile-related products - Determination of thickness at specified pressures - Part 2: Procedure for determination of thickness of single layers of multilayer products |
| ISO 9939-1994 | 航空航天 滑油的压力加油接头(新型) | Aerospace; pressure re-oiling connection (new type) |
| ISO/TR 10501-1993 | 压力作用下液体输送用热塑性塑料管.压头损失的计算 | Thermoplastics pipes for the transport of liquids under pressure; calculation of head losses |
| ISO/TR 7468-1981 | 锅炉和压力容器用锻钢的平均应力断裂特性的概述 | Summary of average stress rupture properties of wrought steels for boilers and pressure vessels |
| ISO/TS 17892-8 Technical Corrigendum 1-2006 | 土工勘查和检验.土壤的实验室检验.第8部分:松散土壤三轴向压力试验 | Geotechnical investigation and testing - Laboratory testing of soil - Part 8: Unconsolidated undrained triaxial test |
| ISO/TS 17892-9 Technical Corrigendum 1-2006 | 土工勘查和检验.土壤的实验室检验.第9部分:渗水土壤的固定三轴向压力试验 | Geotechnical investigation and testing - Laboratory testing of soil - Part 9: Consolidated triaxial compression tests on water-saturated soils |
| ISO/TS 18226-2006 | 塑料管材和管件.压力4 MPa(40 bar)的供气体燃料用加固热塑管道系统 | Plastics pipes and fittings - Reinforced thermoplastics pipe systems for the supply of gaseous fuels for pressures up to 4 MPa (40 bar) |
| 编号 | 中文名称 | 英文名称 |