| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| ANSI/ANS 59.51-1997 | 应急柴油发电机的燃油系统 | Fuel-Oil Systems for Emergency Diesel Generators |
| ANSI/ANS 59.52-1998 | 安全相关应急柴油发电机用润滑油系统 | Lubricating Oil Systems for Safety-Related Emergency Diesel Generators |
| ANSI/ASME PTC29-2005 | 水力涡轮发电机组的速度调节系统 | Speed Governing Systems for Hydraulic Turbine Generators Units |
| ANSI/ASTM A469-1994 | 用于发电机转子的真空处理钢锻件规范 | Specification for Vacuum-Treated Steel Forgings for Generator Rotors |
| ANSI/ASTM F1134-1997 | 船用电动机和发电机绝缘电阻监测器规范 | Specification for Insulation Resistance Monitor for Shipboard Electrical Motors and Generators |
| ANSI/EIA 5200000-D-2000 | 已质量认证的专用电机开关的总规范 | Generic Specification for Special-Use Electromechanical Switches of Certified Quality |
| ANSI/EIA-5200000-D-2000 | 经质量认证的专用电机开关的通用规范 | Generic Specification for Special-Use Electromechanical Switches of Certified Quality |
| ANSI/IEEE 11-2000 | 铁路和道路车辆用旋转电机的标准 | Standard for Rotating Electric Machinery for Rail and Road Vehicles |
| ANSI/IEEE 1110-2002 | 电源系统稳定性分析中同步发电机建模规程和应用指南 | Guide for Synchronous Generator Modeling Practices and Applications in Power System Stability Analyses |
| ANSI/IEEE 112-2004 | 多相感应电机的试验程序 | Test Procedures for Polyphase Induction Machines |
| ANSI/IEEE 115-1995 | 同步电机的试验程序 | Synchronous Machines, Test Procedure for |
| ANSI/IEEE 122-1992 | 汽轮发电机组控制系统的功能性能特征的推荐规程 | Recommended Practice for Functional Performance Characteristics of Control Systems for Steam Turbine Generator Units |
| ANSI/IEEE 125-2007 | 调节驱动发电机的水轮机速度用设备规范编写的推荐实施规程 | Recommended Practice for Preparation of Equipment Specifications for Speed-Governing of Hydraulic Turbines Intended to Drive Electric Generators |
| ANSI/IEEE 1290-1996 | 核电站电动控制阀门电机的应用、保护、控制和试验指南 | Guide for Motor Operated Valve (MOV) Motor Application, Protection, Control, and Testing in Nuclear Power Generating Stations |
| ANSI/IEEE 1310-2004 | 大型发电机线绕定子棒和线圈的热循环试验推荐规程 | Recommended Practice for Thermal Cycle Testing of Form-Wound Stator Bars and Coils for Large Generators |
| ANSI/IEEE 1434-2005 | 旋转电机局部放电测量指南 | Guide to the Measurement of Partial Discharges in Rotating Machinery |
| ANSI/IEEE 1553-2007 | 水轮发电机用模绕线圈和棒耐电压测试的标准 | Standard for Voltage Endurance Testing of Form-Wound Coils and Bars for Hydrogenerators |
| ANSI/IEEE 1665-2009 | 50和60Hz、额定电压1MVA及以上同步发电机的反绕用指南 | Guide for the Rewind of Synchronous Generators, 50 and 60 Hz, Rated 1 MVA and Above |
| ANSI/IEEE 275-1993 | 采用模绕预绝缘定子线圈的交流电机绝缘系统的热量评定推荐规程 | Thermal Evaluation of Insulation Systems for AC Electric Machinery Employing Form-Wound Pre-Insulated Stator Coils, Recommended Practice for |
| ANSI/IEEE 303-2004 | 1类电机辅助设备.A、B、C和D组第2分部所列电机 | Auxiliary Devices for Motors in Class 1 – Groups A, B, C, and D, Division 2 Locations |
| ANSI/IEEE 387-1995 | 作为核电站备用电源的柴油发电机装置的标准准则 | Standard Criteria for Diesel-Generator Units Applied as Standby Power Supplies for Nuclear Power Generating Stations |
| ANSI/IEEE 421.1-2007 | 同步电机励磁系统的标准定义 | Standard Definitions for Excitation Systems for Synchronous Machines |
| ANSI/IEEE 421.3-1997 | 同步电机励磁系统高压试验要求 | Standard for High-Potential Test Requirements for Excitation Systems for Synchronous Machines |
| ANSI/IEEE 43-2000 | 旋转电机绝缘电阻测试的推荐实施规程 | Testing Insulation Resistance of Rotating Machinery, Recommended Practice for |
| ANSI/IEEE 434-2006 | 交流电机额定电压≥2300V的绝缘系统功能评估用指南 | Guide for Functional Evaluation of Insulation Systems for AC Electric Machines Rated 2300 V and Above |
| ANSI/IEEE 492-1999 | 水力发电机运转和维护指南 | Guide for Operation and Maintenance of Hydro-Generators |
| ANSI/IEEE 522-2004 | 交流旋转电机用模绕定子线圈的匝间绝缘试验指南 | Guide for Testing Turn-to-Turn Insulation on Form-Wound Stator Coils for Alternating-Current Rotating Electric Machines |
| ANSI/IEEE 620-1997 | 鼠笼式感应电机的热限值曲线表示指南 | Guide for the Presentation of Thermal Limit Curves for Squirrel Cage Induction Machines |
| ANSI/IEEE 67-2005 | 涡轮发电机的操作和维护指南 | Guide for the Operation and Maintenance of Turbine Generators |
| ANSI/IEEE 762-2006 | 报告发电机组可靠性、有效性和生产率用途的标准定义 | Standard Definitions for Use in Reporting Electric Generating Unit Reliability, Availability, and Productivity |
| ANSI/IEEE 810-1994 | 水轮机和发电机整体锻轴配合和轴公差标准 | Standard for Hydraulic Turbine and Generator Integrally Forged Shaft Couplings and Shaft Tolerances |
| ANSI/IEEE 95-2002 | 带直流高压的交流(AC)电机(2300V及以上)的绝缘测试用推荐实施规范 | Recommended Practice for Insulation Testing of AC Electric Machinery (2300 V and Above) with High Direct Voltage |
| ANSI/IEEE C37.013-1997 | 基于对称电流的额定交流高压发电机断路器用标准 | Standard for AC High-Voltage Generator Circuit Breakers Rated on a Symmetrical Current Basis |
| ANSI/IEEE C37.101-2006 | 发电机接地保护指南 | Guide for Generator Ground Protection |
| ANSI/IEEE C37.101/Cor 1-2007 | 发电机接地保护用指南.技术勘误1:附录A.2相量分析(提供情报的) | Guide for Generator Ground Protection - Corrigendum 1: Annex A.2 Phasor Analysis (Informative) |
| ANSI/IEEE C37.102-2006 | 交流发电机保护指南 | Guide for AC Generator Protection |
| ANSI/IEEE C50.12-2005 | 5MVA及以上水轮机设备用50和60赫兹凸极其同步发电机和发电机/电动机标准 | Standard for Salient-Pole 50 and 60 Hz Synchronous Generators and Generator/Motors for Hydraulic Turbine Applications Rated 5 MVA and Above |
| ANSI/IEEE C50.13-2005 | 10MVA及以上的50和60赫兹鼓形转子同步发电机标准 | Standard for Cylindrical-Rotor 50 and 60 Hz, Synchronous Generators Rated 10 MVA and Above |
| ANSI/IEEE C57.116-1990 | 直接连于发电机的变压器指南 | Guide for Transformers Directly Connected to Generators |
| ANSI/IEEE C62.21-2003 | 1000V及以上的交流旋转电机上浪涌电压保护设备的应用指南 | Guide for the Application of Surge Voltage Protective Equipment on AC Rotating Machinery 1000 V and Greater (including IEEE C62.21/Cor1-2008) |
| ANSI/IEEE C62.92.2-1989 | 公用电力系统中线接地应用指南.第2部分:同步发电机系统电涌保护器件的接地 | Guide for the Application of Neutral Grounding in Electrical Utility Systems, Part II - Grounding of Synchronous Generator Systems |
| ANSI/IEEE C62.92.3-1993 | 发电机辅助系统中性接地应用指南 | Guide for the Application of Neutral Grounding in Electrical Utility Systems, Part III - Generator Auxiliary Systems |
| ANSI/NECA 404-2006 | 安装发电机设备用操作规程建议 | Recommended Practice for Installing Generator Sets |
| ANSI/NECA 406-2003 | 住宅用发电机组安装的推荐规程 | Recommended Practice for Installing Residential Generator Sets |
| ANSI/NECA 90-2004 | 住宅发电机组的安装推荐实施规程 | Recommended Practice for Commissioning Building Electrical Systems |
| ANSI/NEMA MG1, Revision 1-2003 | 电动机和发电机 | Motors and Generators |
| ANSI/RVIA EGS-1-2008 | 游乐车辆发动机的发电机组 | Engine Generator Sets for Recreational Vehicles |
| ANSI/UL 1004-4-2008 | 发电机安全标准 | Standard for Safety for Electric Generators |
| ANSI/UL 1236-2010 | 装载发电机启动器蓄电池用蓄电池充电器的安全性标准(提议日期9-18-09) | Standard for Safety for Battery Chargers for Charging Engine-Starter Batteries (Proposal dated 9-18-09) |
| ANSI/UL 2200A-2009 | 固定发电机组件用安全标准 | Standard for Safety for Stationary Engine Generator Assemblies |
| ANSI/UL 2200B-2009 | 静止式发动机和发电机组合机组的安全标准 | Standard for Safety for Stationary Engine Generator Assemblies |
| ANSI/UL 60947-4-1-2007 | 低压开关设备和控制设备的安全标准.第4-1部分:电流接触器和电动机起动器.电机接触器和电动机起动器 | Standard for Safety for Low-Voltage Switchgear and Controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
| ANSI/UL 674-2008 | 危险场所用电动机和发电机的安全标准 | Standard for Safety for Electric Motors and Generators for Hazardous Locations (proposal dated 4-18-08) |
| ASME PTC 20.1-1977 | 汽轮发电机组的速度和负载调节系统 | (Speed and load governing systems for steam turbine-generator units) |
| ASME PTC 20.2-1965 | 汽轮发电机组用超速自动分离系统 | (Overspeed trip systems for steam turbine-generator units) |
| ASME PTC 20.3-1970 | 汽轮发电机组用压力控制系统 | (Pressure control systems used on steam turbine-generator units) |
| ASME PTC 26-1962 | 内燃发电机组的速度调节系统 | (Speed-governing systems for internal combustion engine-generator units) |
| ASME PTC 29-1965 | 液压汽轮发电机组的速度调节系统 | (Speed-governing systems for hydraulic turbine-generator units) |
| ASTM D4286-2008 | 核动力发电机装置用涂覆承包人资格鉴定的标准实施规程 | Standard Practice for Determining Coating Contractor Qualifications for Nuclear Powered Electric Generation Facilities |
| ASTM F1134-1994(2007) | 船用电动机和发电机绝缘电阻监测器 | Standard Specification for Insulation Resistance Monitor for Shipboard Electrical Motors and Generators |
| IEEE 1095-1989 | 水电用立式发电机和发电机/电动机安装指南 | (Guide for installation of vertical generators and generator/motors for hydroelectric applications) |
| IEEE 11-2000 | 铁路和公路车辆用旋转电机标准 | (Standard for rotating electric machinery for rail and road vehicles) |
| IEEE 1110-1991 | 稳定性分析中同步电机模拟操作指南 | (Guide for synchronous generator modeling practices in stability analyses) |
| IEEE 112-1996 | 多相感应电动机及发电机的试验规程 | (Test procedure for polyphase induction motors and generators) |
| IEEE 1129-1992 | 涡轮发电机监测仪表用推荐规范 | (Recommended practice for monitoring and instrumentation of turbine generators) |
| IEEE 115-1995 | 同步电机的试验程序.第1部分:验收和性能试验.第2部分:动态分析的试验程序控制和参数测定 | (Test procedures for synchronous machines - Part 1: Acceptance and performance testing - Part 2: Test procedures and parameter determination for dynamic analysis) |
| IEEE 117-1974 | 不规则缠绕交流电机绝缘材料系统的评定试验程序 | (Test procedure for evaluation of systems of insulation materials for random-wound ac electric machinery) |
| IEEE 1193-1994 | 发电机频率对环境影响的测量标准 | (Measurement of environmental sensitivities of standard frequency generators) |
| IEEE 122-1991 | 汽轮机发电机组控制系统功能与性能特征的推荐规程 | (Recommended practice for functional and performance characteristics of control systems for steam turbine-generator units) |
| IEEE 1290-1996 | 核电站中电动阀门(MOV)的电机使用,保护,控制和试验的指南 | (Guide for motor operated valve (MOV) motor application, protection, control, and testing in nuclear power generating stations) |
| IEEE 1310-1996 | 大型发电机用模绕定子棒和模绕线圈的热循环试验 | (Thermal cycle testing of form-wound stator bars and coils for large generators) |
| IEEE 1434-2000 | 旋转电机中局部放电测量的试用指南 | (Trial-use guide to the measurement of partical discharges in rotating machinery) |
| IEEE 1553-2002 | 水轮发电机用模绕线圈和棒的电压耐久性试验 | (Voltage-endurance testing of form-wound coils and bars for hydrogenerators) |
| IEEE 275-1992 | 交流电机绝缘系统的热评定推荐规程.额定电压6900V及以下电机模绕预绝缘定子线圈的使用 | (Recommended practice for thermal evaluation of insulation systems for alternating-current electric machinery; employing form-wound preinsulated stator coils for machines rated 6900 V and below) |
| IEEE 286-2000 | 电机定子线圈绝缘的功率因数tip-up测量的推荐实施规程 | (Recommended practice for measurement of power factor tip-up of electric machinery stator coil insulation) |
| IEEE 304-1977 | 直流电机用绝缘系统评定及分类的试验规程 | (Test procedure for evaluation and classification of insulation systems for direct-current machines) |
| IEEE 387-1995 | 用作核电站备用电源的柴油发电机组准则 | (Criteria for diesel-generator units applied as standby power supplies for nuclear power generating stations) |
| IEEE 421.1-1986 | 同步电机励磁系统的定义 | (Definitions for excitation systems for synchronous machines) |
| IEEE 429-1994 | 使用额定电压6900V及以下电机模绕预绝缘定子线圈的AC电机的热绝缘评定推荐规程 | (Recommended practice for thermal evaluation of sealed insulation systems for AC electric machinery employing form-wound preinsulated stator coils for machines rated 6900 V and below) |
| IEEE 43-2000 | 检测旋转电机绝缘电阻的推荐实施规范 | (Recommended practice for testing insulation resistance of rotating machinery) |
| IEEE 432-1992 | 旋转电机(5hp-10000hp)绝缘维护指南 | (Guide for insulation maintenance for rotating electric machinery (5 hp to less than 10000 hp)) |
| IEEE 433-1974 | 高压甚低频大型旋转电机绝缘试验的推荐规程 | (Recommended practice for insulation testing of large ac rotating machinery with high voltage at very low frequency) |
| IEEE 434-1973 | 大型高压电机绝缘系统功能评定指南 | (Guide for functional evaluation of insulation systems for large high-voltage machines) |
| IEEE 522-1992 | 交流旋转电机模绕定子线圈匝间绝缘的试验指南 | (Guide for testing turn-to-turn insulation on form-wound stator coils for alternating-current rotating electric machines) |
| IEEE 56-1977 | 大型交流旋转电机(10kVA及以上)绝缘维护指南 | (Guide for insulation maintenance of large ac rotating machinery (10000 kVA and larger)) |
| IEEE 67-1990 | 涡轮发电机操作和维护指南 | (Guide for operation and maintenance of turbine generators) |
| IEEE C 37.013-1997 | 基于平衡电流的交流高压发电机断路器 | (AC high-voltage generator circuit breakers rated on a symmetrical current basis) |
| IEEE C 37.101-1993 | 发电机接地保护指南 | (Guide for generator ground protection) |
| IEEE C 37.102-1995 | 交流发电机保护指南 | (Guide for ac generator protection) |
| IEEE C 37.18-1979 | 旋转电机用封闭场励磁放电断路器 | (Enclosed field discharge circuit breakers for rotating electric machinery) |
| IEEE C 50.14-1977 | 燃汽轮机驱动的圆柱转子同步电机的技术要求 | (Requirements for combustion gas turbine driven cylindrical rotor synchronous generators) |
| IEEE C 57.116-1989 | 同发电机直接相连的变压器指南 | (Guide for transformers directly connected to generators) |
| IEEE C 62.92.2-1989 | 电力事业系统中性接地应用指南.第二部分:同步发电机系统接地 | (Guide for the application of neutral grounding in electrical utility systems; part 2: grounding of synchronous generator systems) |
| IEEE C 62.92.3-1993 | 电力事业系统中性接地应用指南.第三部分:发电机辅助系统 | (Guide for the application of neutral grounding in electrical utility systems - Part 3: Generator auxiliary systems) |
| UL 1112-1997 | 船用电动机和发电机(启动、外驱动倾角、配平片、发电机、交流发电机) | (Marine electric motors and generators (cranking, outdrive tilt, trim tab, generators, alternators) ) |
| UL 1248-1993 | 旅游车用发动机和发电机组合机组 | (Engine-generator assemblies for use in recreational vehicles ) |
| UL 1310-1994 | 2级发电机组 | (Class 2 power units ) |
| UL 1411-1998 | 音频、无线电和电视类装置用变压器与电机变压器 | (Transformers and motor transformers for use in audio-, radio-, and television-type appliances ) |
| UL 674-2003 | 1类危险场所用电动机和发电机 | (Electric motors and generators for use in division 1 hazardous (classified) locations ) |
| 编号 | 中文名称 | 英文名称 |