| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| BS 1756-4-1977 | 烟道气体的取样与分析方法.第4部分:综合分析 | Methods for sampling and analysis of flue gases - Miscellaneous analyses |
| BS 2069-1954 | 气体取样管规范 | Specification for gas sampling tubes |
| BS 2L 508-1973 | 镁-1<1/4>%锌(1.25)-锆(0.6)合金棒材和挤压型材规范(适用于隋性气体保护弧焊技术)(直径不超过50mm或较小截 | Specification for bars and extruded sections of magnesium-11/4% zinc-zirconium alloy (suitable for welding by inert-gas shielded arc techniques) (not exceeding 50 mm diameter or minor sectional dimension) (Zn 1.25, Zr 0.6) |
| BS 2L 509-1973 | 镁-锌(1.25)-锆(0.6)合金管规范(适用于隋性气体保护弧焊技术) | Specification for tube of magnesium-11/4% zinc-zirconium alloy (suitable for welding by inert-gas shielded arc techniques) (Zn 1.25 , Zr 0.6) |
| BS 3048-1958 | 烟道气体连续取样与自动分析规程.指示器与记录仪 | Code for the continuous sampling and automatic analysis of flue gases: indicators and recorders |
| BS 3156-10.3.1-1987 | 气体燃料分析.第10部分::通用方法.第3节:水露点和相关湿度测定.第1小节:表面冷却冷凝湿度计原理及使用说明 | Analysis of fuel gases - General methods - Determination of water dew point and relative humidity - Principles of cooled surface condensation hygrometers and general description of their use |
| BS 3156-11.1.2-1997 | 燃气分析.第11部分:天然气.第1节:碳氢化合物和惰性气体分析.第2小节:气体色谱法展开分析 | Analysis of fuel gases - Methods for non-manufactured gases - Hydrocarbons and inert gases - Extended analysis by gas chromatographic method |
| BS 3156-11.5-1996 | 燃气分析.非制造气体法.在线分析系统的性能评估 | Analysis of fuel gases - Methods for non-manufactured gases - Performance evaluation for on-line analytical systems |
| BS 3212-1991 | 液化石油气体气相与液化石油气露天装置用挠性橡皮管、橡皮软管及软管组件规范 | Specification for flexible rubber tubing, rubber hose and rubber hose assemblies for use in LPG vapour phase and LPG/air installations |
| BS 341-3-2002 | 可运输气体容器的阀门.阀门出口接头 | Transportable gas container valves - Valve outlet connections |
| BS 341-4-2004 | 可运输气体容器的阀门.减压装置 | Transportable gas container valves - Pressure relief devices |
| BS 3900-J6-1993 | 涂料试验方法.第J6部分:粉末涂层试验.用气体比对测重计测定粉末涂层密度(参照法) | Methods of test for paints - Testing of coating powders - Determination of density of coating powders by gas comparison pyknometer (referee method) |
| BS 3900-J9-1993 | 涂料试验方法.第J9部分:粉末涂层/气体混合物流动特性测定 | Methods of test for paints - Testing of coating powders - Determination of flow properties of a coating powder/air mixture |
| BS 4359-1-1996 | 粉末比表面积的测定.第1部分:气体表面吸附(BET)推荐方法(包括多孔物质) | Determination of the specific surface area of powders - BET method of gas adsorption for solids (including porous materials) |
| BS 4359-4-1995 | 粉末表面系数的测定.第4部分:使用气体表面吸附(BET)技术测定金属表面积推荐方法 | Determination of the specific surface area of powders - Recommendations for methods of determination of metal surface area using gas adsorption techniques |
| BS 4553-3-1998 | 600/1000V单相分芯同轴电缆规范.第3部分:带热固绝缘层和遇火有低发散烟雾和腐蚀性气体的电缆 | Specification for 600/1000 V single-phase split concentric electric cables - Cables having thermosetting insulation and low emission of smoke and corrosive gases when affected by fire |
| BS 4559-4-2000 | 校正用混合气体的制备方法.混合气体制备证书 | Methods for preparation of calibration gas mixtures - Certificate of mixture preparation |
| BS 4559-9.2-1988 | 标定混合气体制备方法.第9部分:比对法和溯源能力的确定方法.第2节:比对检验方法 | Methods for preparation of calibration gas mixtures - Comparison methods and methods for establishing traceability - Checking by a comparison method |
| BS 4872-2-1976 | 不要求批准焊接工艺时焊工的鉴定考试规范.第2部分:铝及铝合金钨极惰性气体保护电弧焊或熔化极惰性气体保护 | Specification for approval testing of welders when welding procedure approval is not required - TIG or MIG welding of aluminium and its alloys |
| BS 5045-2-1989 | 可运输的气体容器.第2部分:0.5L-450L水容量的焊接钢容器规范 | Transportable gas containers - Specification for steel containers of 0.5 L up to 450 L water capacity with welded seams |
| BS 5045-6-1987 | 可运输的气体容器.第6部分:小于0.5L水容量的无缝容器规范 | Transportable gas containers - Specification for seamless containers of less than 0.5 litre water capacity |
| BS 5045-7-2000 | 可运输的气体容器.特殊便携的水容量为0.5-15升的无缝钢气体容器的规范 | Transportable gas containers - Specification for seamless steel gas containers of water capacity 0.5 L up to 15 L for special portable applications |
| BS 5343-2-1991 | 气体检测管.第2部分:长期气体检测管规范 | Gas detector tubes - Specification for long term gas detector tubes |
| BS 5598-11-1983 | 卤代烃取样和试验方法.第11部分:氯氟代烃惰性气体含量测定:气相色谱法:总则 | Methods of sampling and test for halogenated hydrocarbons - Determination of 'inert' gas content of chlorofluorohydrocarbons, gas chromatographic method, general principles |
| BS 5857-2.1-1980 | 密封管道中流体流量的示踪剂测量法.第2部分:气体流量测量.第1节:总则 | Methods for measurement of fluid flow in closed conduits, using tracers - Measurement of gas flow - General |
| BS 5857-2.4-1980 | 使用示踪剂的密封管道中流体流量的测量方法.气体流量的测量.采用放射性示踪剂的过渡时间法 | Methods for measurement of fluid flow in closed conduits, using tracers - Measurement of gas flow - Transit time method using radioactive tracers |
| BS 5871-1-2005 | 燃气炉、对流式加热器、回火锅炉和装饰性燃料气体器具的安装和维修规范.燃气炉、对流式加热器、回火锅炉和 | Specification for the installation and maintenance of gas fires, convector heaters, fire/back boilers and decorative fuel effect gas appliances - Gas fires, convector heaters, fire/back boilers and heating stoves (2nd and 3rd family gases) |
| BS 5871-2-2005 | 燃气炉、对流式加热器、回火锅炉和装饰性燃料气体器具的安装和维修规范.输入热量不超过15kW的插入式燃料气 | Specification for the installation and maintenance of gas fires, convector heaters, fire/back boilers and decorative fuel effect gas appliances - Inset live fuel effect gas fires of heat input not exceeding 15 kW, and fire/back boilers (2nd and 3rd family gases) |
| BS 5871-3-2005 | 燃气炉、对流式加热器、回火锅炉和装饰性燃料气体器具的安装和维修规范.输入热量不超过20kW的装饰性燃料气 | Specification for the installation and maintenance of gas fires, convector heaters, fire/back boilers and decorative fuel effect gas appliances - Decorative fuel effect gas appliances of heat input not exceeding 20 kW (2nd and 3rd family gases) |
| BS 5871-4-2007 | 煤气加热器、对流式加热器、回火锅炉和装饰性燃料气体器具的安装和维修规范.额定热输入不超过6kW的独立式无 | Specification for the installation and maintenance of gas fires, convector heaters, fire/back boilers and decorative fuel effect gas appliances - Independent gas-fired flueless fires, convector heaters and heating stoves of nominal heat input not exceeding 6 kW (2nd and 3rd family gases) |
| BS 6069-3.3-1991 | 空气质量表征.第3部分:工作场所空气.第3节:用木炭管/溶剂解吸/气体色谱仪测定汽态氯化烃的方法 | Characterization of air quality - Workplace atmospheres - Method for the determination of vaporous chlorinated hydrocarbons by charcoal tube/solvent desorption/gas chromatography |
| BS 6069-3.4-1991 | 空气质量表征.第3部分:工作场所空气.第4节:用木炭管/溶剂解吸/气体色谱仪测定汽态芳香烃氯化烃的方法 | Characterization of air quality - Workplace atmospheres - Method for the determination of vaporous aromatic hydrocarbons by charcoal tube/solvent desorption/gas chromatography |
| BS 6202-1982 | 空气或其他气体净化设备术语 | Glossary of terms for cleaning equipment for air or other gases |
| BS 6656-2002 | 由射频辐射引起的易燃气体意外着火的评定.指南 | Assessment of inadvertent ignition of flammable atmospheres by radio-frequency radiation - Guide |
| BS 6713-2-1986 | 防爆系统.第2部分:空气中易燃气体爆炸指数的测定方法 | Explosion protection systems - Method for determination of explosion indices of combustible gases in air |
| BS 6713-3-1986 | 防爆系统.第3部分:不同于粉尘/空气和气体/空气混合物的燃料/空气混合物爆炸指数的测定方法 | Explosion protection systems - Method for determination of explosion indices of fuel/air mixtures other than dust/air and gas/air mixtures |
| BS 6724-1997 | 采用热固绝缘和受火情影响时散发出少量烟雾和腐蚀气体的600/1000V和1900/3300V铠装电缆规范 | Electric cables - Thermosetting insulated, armoured cables for voltages of 600/1000 V and 1900/3300 V, having low emission of smoke and corrosive gases when affected by fire |
| BS 6843-3-1988 | 石油燃料的分类.第3部分:液化石油气体 | Classification of petroleum fuels - Liquefied petroleum gases |
| BS 6904-1987 | 额定电压等于或高于72.5kV的气体绝缘金属封闭式开关装置用电缆连接件指南 | Guide for cable connections for gas-insulated metal-enclosed switchgear for rated voltages of 72.5 kV and above |
| BS 6942-2-1989 | 氧燃料气体焊接和相关工艺用成套小型工具的设计和建造.第2部分:使用可充氧气和燃气容器的成套工具规范 | Design and construction of small kits for oxy-fuel gas welding and allied processes - Specification for kits using refillable gas containers for oxygen and fuel gas |
| BS 7122-1989 | 液化气体道路运输用的焊接钢槽车规范 | Specification for welded steel tanks for the road transport of liquefiable gases |
| BS 7211-1998 | 受火情影响时排放少量烟雾和腐蚀性气体的电力和照明设备用热固绝缘(非铠装)电缆规范 | Electric cables - Thermosetting insulated, non-armoured cables for voltages up to and including 450/750 V, for electric power, lighting and internal wiring, and having low emission of smoke and corrosive gases when affected by fire |
| BS 7406-1991 | 用动态吹气和静态气体法对纸和纸板的水蒸汽透湿率的测定方法 | Methods for determination of water vapour transmission rate of sheet materials (paper and board) by dynamic sweep and static gas methods |
| BS 7420-1991 | 固体、液体和气体燃料热值的测定指南 | Guide for determination of calorific values of solid, liquid and gaseous fuels (including definitions) |
| BS 7461-1991 | 装有流量调节器、闭路开关检验、闭合位置指示开关或气流量控制器电动式气体自动关闭阀规范 | Specification for electrically operated automatic gas shut-off valves fitted with throughput adjusters, proof of closure switches, closed position indicator switches or gas flow control |
| BS 7629-1-1997 | 具有低排放烟雾和腐蚀性气体的300/500 V电缆受火情影响时的耐火规范.第1部分:多心电缆 | Specification for 300/500 V fire resistant electric cables having low emission of smoke and corrosive gases when affected by fire - Multicore cables |
| BS 7629-2-1997 | 具有低排放烟雾和腐蚀性气体的300/500 V电缆受火情影响时的耐火规范.第2部分:多双股电缆 | Specification for 300/500 V fire resistant electric cables having low emission of smoke and corrosive gases when affected by fire - Multipair cables |
| BS 7634-1993 | 医疗用气体管道系统用氧化浓缩器规范 | Specification for oxygen concentrators for use with medical gas pipeline systems |
| BS 7655-6.1-1997 | 电缆绝缘和铠装材料规范.具有低排放腐蚀性气体的和适用于着火时具有低排放烟雾的电缆热塑铠装化合物.通用热 | Specification for insulating and sheathing materials for cables - Thermoplastic sheathing compounds having low emission of corrosive gases, and suitable for use in cables having low emission of smoke when affected by fire - General application thermoplastic types |
| BS 7838-1996 | 直径达到28 mm的低压气体管道系统用的波纹状不锈钢半硬式管材和有关配件规范 | Specification for corrugated stainless steel semi-rigid pipe and associated fittings for low-pressure gas pipework of up to 28 mm |
| BS 7846-2000 | 电缆.受火影响时排放少量烟和腐蚀气体的600/1000 V 热固绝缘铠装耐火电缆 | Electric cables - 600/1000 V armoured fire-resistant cables having thermosetting insulation and low emission of smoke and corrosive gases when affected by fire |
| BS 7870-3.12-2001 | 供电与动力装置用低电压和常电压聚合绝缘电缆.额定电压为0.6/1KV的配电电缆规范.当有火焰影响时烟和腐蚀性 | LV and MV polymeric insulated cables for use by distribution and generation utilities - Specification for distribution cables of rated voltage 0.6/1 kV - XLPE insulated combined neutral and earth copper wire concentric cables with copper or aluminium conductors, having low emission of smoke and corrosive gases when affected by fire |
| BS 7870-3.50-2005 | 配电和发电装置用低压和常压聚合绝缘电缆.额定电压为0.6/1KV的配电电缆规范.着火时轻微散发烟气和腐蚀性气 | LV and MV polymeric insulated cables for use by distribution and generation utilities - Specification for distribution cables of rated voltage 0.6/1 kV - XLPE insulated, copper wire waveform or helical concentric cables with solid aluminium conductors, having low emission of smoke and corrosive gases when affected by fire - (Implementation of HD 603) |
| BS 7965-2000 | 工业气体用对角线路径通过时间超声波流量计的选择、装配、操作和校准 | The selection, installation, operation and calibration of diagonal path transit time ultrasonic flowmeters for industrial gas applications |
| BS 8436-2004 | 电缆.墙、隔墙和建筑物空间中使用的着火时有低排烟量和腐蚀气体释放的300/500V屏蔽电缆.多芯电缆 | Electric cables - 300/500 V screened electric cables having low emission of smoke and corrosive gases when affected by fire, for use in walls, partitions and building voids - Multicore cables |
| BS 8447-2005 | 麻醉和呼吸设备.麻醉气体传输装置雾化器附件用钩接式配件 | Anaesthetic and respiratory equipment - Hook-on fittings for the attachment of vaporizers to an anaesthetic gas delivery device |
| BS 8478-2006 | 呼吸保护装置.潜水用呼吸气体和施压供养设施 | Respiratory protective devices - Breathing gases for diving and hyperbaric applications |
| BS C 17-1973 | 发动机启动用低压气体连接的连接件尺寸规范 | Specification for coupling dimensions for low pressure air connections for engine starting |
| BS DD 221-1997 | 气体器具作标记的一般指南 | General guidance for the marking of gas appliances |
| BS DD CEN ISO/TS 15011-5-2006 | 焊接和相关工艺的卫生和安全.烟尘和气体取样的试验室方法.通过完全或部分有机材料组成的产品焊接或切割时所 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Identification of thermal-degradation products generated when welding or cutting through products composed wholly or partly of organic materials |
| BS DD CEN/TS 15439-2007 | 生物质气化.气体产品中的焦油和粒子.抽样和分析 | Biomass gasification - Tar and particles in product gases - Sampling and analysis |
| BS DD CEN/TS 1555-7-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).合格评定指南 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Guidance for the assessment of conformity |
| BS DD ENV 12290-1996 | 高技术陶瓷.在惰性气体环境中在高温下陶瓷复合材料的机械特性.平面内抗压强度的测定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of compression properties |
| BS DD ENV 737-6-2003 | 医用气体管道系统.压缩医用气体终端设备和真空终端设备用探针的尺寸和定位 | Medical gas pipeline systems - Dimensions and allocation of probes for terminal units for compressed medical gases and vacuum |
| BS DD ISO/TS 11155-2-2002 | 道路车辆.乘客舱内空气过滤器.气体过滤试验 | Road vehicles - Air filters for passenger compartments - Test for gaseous filtration |
| BS EN 10276-2-2003 | 钢铁材料的化学分析.钢和铁中氧的含量测定.在惰性气体中熔解后红外法 | Chemical analysis of ferrous materials - Determination of oxygen in steel and iron - Infrared method after fusion under inert gas |
| BS EN 10301-2003 | 岸上及海底管道用钢管及配件.非腐蚀性气体的输送用减少摩擦的内涂层 | Steel tubes and fittings for on and offshore pipelines - Internal coating for the reduction of friction for conveyance of non corrosive gas |
| BS EN 1057-2006 | 铜和铜合金制品.卫生设备和水加热器的水和气体用无缝圆铜管 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| BS EN 1076-1997 | 工作地点的环境.测定气体和蒸气用的泵吸附管.要求和试验方法 | Workplace atmospheres - Pumped sorbent tubes for the determination of gases and vapours - Requirements and test methods |
| BS EN 1084-1995 | 胶合板.用气体分析法测定甲醛释放级别 | Plywood - Formaldehyde release classes determined by the gas analysis method |
| BS EN 1093-2-2006 | 机械安全.空气中有害物质排放的评估.特定污染物排放率测量用示踪气体法 | Safety of machinery - Evaluation of the emission of airborne hazardous substances - Tracer gas method for the measurement of the emission rate of a given pollutant |
| BS EN 12022-1999 | 血液气体交换器 | Blood-gas exchangers |
| BS EN 12067-2-2004 | 气体燃烧器和燃气装置用燃气/空气比率控制装置.电子型 | Gas/air ratio controls for gas burners and gas burning appliances - Electronic types |
| BS EN 12083-1998 | 呼吸保护装置.带呼吸软管的过滤器(无面具装配).颗粒过滤器、气体过滤器及颗粒与气体过滤器.要求、试验、标 | Respiratory protective devices - Filters with breathing hoses, (non-mask mounted filters) - Particle filters, gas filters, and combined filters - Requirements, testing, marking |
| BS EN 12094-1-2003 | 固定式消防系统.气体灭火系统用元件.电自动控制和延迟装置的要求和试验方法 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for electrical automatic control and delay devices |
| BS EN 12094-10-2003 | 固定消防系统.气体灭火系统元件.压力计和压力开关的试验方法和要求 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for pressure gauges and pressure switches |
| BS EN 12094-11-2003 | 固定消防系统.气体灭火系统元件.机械称重设备的试验方法和要求 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for mechanical weighing devices |
| BS EN 12094-12-2003 | 固定消防系统.气体灭火系统元件.气动警报装置的试验方法和要求 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for pneumatic alarm devices |
| BS EN 12094-13-2001 | 固定消防系统.气体灭火系统元件.止回阀和非止回阀试验方法和要求 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for check valves and non-return valves |
| BS EN 12094-16-2003 | 固定消防系统.气体灭火系统元件.CODOWN2低压系统用添味装置的试验方法和要求 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for odorizing devices for CO2 low pressure systems |
| BS EN 12094-2-2003 | 固定式消防系统.气体灭火系统用元件.非电子自动控制和延迟装置的要求和试验方法 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for non-electrical automatic control and delay devices |
| BS EN 12094-3-2003 | 固定消防系统.气体灭火系统元件.手动触发和止动装置的试验方法和要求 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for manual triggering and stop devices |
| BS EN 12094-4-2004 | 固定式消防系统.气体灭火系统用元件.容器阀组件及其传动器的要求和试验方法 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for container valve assemblies and their actuators |
| BS EN 12094-5-2006 | 固定消防系统.气体灭火系统用元件.高压和低压选择器阀门及其调节器的要求和试验方法 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for high and low pressure selector valves and their actuators |
| BS EN 12094-6-2006 | 固定消防系统.气体灭火系统用元件.非电气失效装置的要求和试验方法 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for non-electrical disable devices |
| BS EN 12094-7-2001 | 固定消防系统.气体灭火系统元件.CO2系统用喷嘴的要求和试验方法 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for nozzles for CO2 systems |
| BS EN 12094-8-2006 | 固定消防系统.气体灭火系统用元件.连接器的要求和试验方法 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for connectors |
| BS EN 12094-9-2003 | 固定消防系统.气体灭火系统元件.专用火灾探测器的试验方法和要求 | Fixed firefighting systems - Components for gas extinguishing systems - Requirements and test methods for special fire detectors |
| BS EN 12115-2000 | 液体或气体化学药品用橡胶和热塑软管和软管组件.规范 | Rubber and thermoplastics hoses and hose assemblies for liquid or gaseous chemicals - Specification |
| BS EN 12117-1998 | 塑料管道系统.管件、阀门和附件.气体流速与压降之间关系的测定 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| BS EN 12290-2005 | 高级工业陶瓷.惰性气体高温条件下陶瓷复合材料的机械性能.耐压特性测定 | Advanced technical ceramics — Mechanical properties of ceramic composites at high temperature under inert atmosphere — Determination of compression properties |
| BS EN 12470-3-2000 | 临床体温计.最大装置的压缩式电气体温计(非预测式和预测式)的性能 | Clinical thermometers - Performance of compact electrical thermometers (non-predictive and predictive) with maximum device |
| BS EN 12619-1999 | 固定源辐射.低浓缩下烟道气体中总气态有机碳的浓缩质量测定.连续火焰电离检测器法 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon at low concentrations in flue gases - Continuous flame ionization detector method |
| BS EN 12755-2000 | 可运输式气体钢瓶.乙炔灌装条件 | Transportable gas cylinders - Filling conditions for acetylene bundles |
| BS EN 12788-2005 | 高级工业陶瓷.惰性气体高温下陶瓷复合材料的机械性能.抗弯强度的测定 | Advanced technical ceramics — Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of flexural strength |
| BS EN 1279-3-2003 | 建筑玻璃.绝缘玻璃组件.长期试验法以及漏气率和气体浓度公差的要求 | Glass in building - Insulating glass units - Long term test method and requirements for gas leakage rate and for gas concentration tolerances |
| BS EN 12952-8-2002 | 水管锅炉和辅助设备.锅炉的液体和气体燃料的燃烧系统要求 | Water-tube boilers and auxiliary installations - Requirements for firing systems for liquid and gaseous fuels for the boiler |
| BS EN 12953-7-2002 | 火管锅炉.锅炉用液体和气体燃料的点火系统要求 | Shell boilers - Requirements for firing systems for liquid and gaseous fuels for the boilers |
| BS EN 13014-2000 | 麻醉和呼吸设备用气体取样管的连接 | Connections for gas sampling tubes to anaesthetic and respiratory equipment |
| BS EN 13016-1-2007 | 液化石油产品.蒸气压力.气体饱和蒸气压(ASVP)的测定和干蒸气压当量值(DVPE)的计算 | Liquid petroleum products - Vapour pressure - Determination of air saturated vapour pressure (ASVP) and calculated dry vapour pressure equivalent (DVPE) |
| BS EN 13028-2001 | 包装.轻型金属包装.由标称容量限定的有或无填充气体的圆形敞口容器 | Packaging - Light-gauge metal packaging - Round open-top cans for beverage products with or without added gas, defined by their nominal filling volumes |
| BS EN 13090-2000 | 建筑物内气体管道的螺纹接头重新密封方法 | Means for resealing threaded joints of gas pipework in buildings |
| BS EN 13096-2004 | 可运输储气瓶.填充气体到容器内的条件.单组分气体 | Transportable gas cylinders - Conditions for filling gases into receptacles - Single component gases |
| BS EN 13099-2004 | 可运输气瓶.气体混合物装填到容器中的条件 | Transportable gas cylinders - Conditions for filling gas mixtures into receptacles |
| BS EN 13185-2001 | 无损检验.渗漏试验.示踪气体法 | Non-destructive testing - Leak testing - Tracer gas method |
| BS EN 13235-2006 | 高级技术陶瓷.在惰性气体高温条件下陶瓷复合材料的机械特性.蠕变特性测定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of creep behaviour |
| BS EN 1326-1996 | 气焊设备.气体硬钎焊和焊接用小型设备箱 | Gas welding equipment - Small kits for gas brazing and welding |
| BS EN 13293-2002 | 可运输储气瓶.压缩、液化和溶解气体用的水容量高达0.5升和二氧化碳用的水容量高达１升的可再充装无缝正火碳 | Transportable gas cylinders - Specification for the design and construction of refillable transportable seamless normalized carbon manganese steel gas cylinders of water capacity up to 0,5 litre for compressed, liquefied and dissolved gases and up to 1 litre for carbon dioxide |
| BS EN 13348-2001 | 铜和铜合金.医用气体或真空用无缝圆铜管 | Copper and copper alloys - Seamless, round copper tubes for medical gases or vacuum |
| BS EN 13365-2002 | 可运输气瓶.永久的和液化的气体(乙炔除外)的钢瓶组件.灌装时的检验 | Transportable gas cylinders - Cylinder bundles for permanent and liquefied gases (excluding acetylene) - Inspection at time of filling |
| BS EN 13385-2002 | 可运输气瓶.永久的和液化的气体(乙炔除外)用蓄电池驱动车辆.灌装时的检验 | Transportable gas cylinders - Battery vehicles for permanent and liquefied gases (excluding acetylene) - Inspection at time of filling |
| BS EN 13528-1-2002 | 环境空气质量.测定气体和蒸汽浓缩度的扩散样品.要求和试验方法.一般要求 | Ambient air quality - Diffusive samplers for the determination of concentrations of gases and vapours - Requirements and test methods - General requirements |
| BS EN 13528-2-2002 | 环境空气质量.测定气体和蒸汽浓缩度的扩散样品.要求和试验方法.特殊要求和试验方法 | Ambient air quality - Diffusive samplers for the determination of concentrations of gases and vapours - Requirements and test methods - Specific requirements and test methods |
| BS EN 13528-3-2003 | 环境空气质量.测定气体和蒸气浓度用扩散样品.要求和试验方法.选择、使用和维护指南 | Ambient air quality - Diffusive samplers for the determination of concentrations of gases and vapours - Requirements and test methods - Guide to selection, use and maintenance |
| BS EN 13611-2000 | BS EN 13611-2000:气体燃烧器和燃气器具的安全和控制设备.一般要求 | BSEN13611 : 2000 Safety and control devices for gas burners and gas-burning appliances - General requirements |
| BS EN 13622-2002 | 气体焊接设备.术语.气体焊接使用的术语 | Gas welding equipment - Terminology - Terms used for gas welding equipment |
| BS EN 13625-2002 | 无损检验.泄漏试验.气体泄漏测量用仪表选择指南 | Non-destructive testing - Leak test - Guide to the selection of instrumentation for the measurement of gas leakage |
| BS EN 13628-1-2002 | 包装.软性包装材料.应用静态液体上部气体色谱分析法测定剩余溶质.绝对法 | Packaging - Flexible packaging material - Determination of residual solvents by static headspace gas chromatography - Absolute methods |
| BS EN 13631-16-2004 | 民用爆炸物.烈性炸药.毒性气体的检测和测量 | Explosives for civil uses - High explosives - Detection and measurement of toxic gases |
| BS EN 13673-1-2003 | 气体和蒸气的最大爆炸压力和最大压升的测定.最大爆炸压力的测定 | Determination of the maximum explosion pressure and the maximum rate of pressure rise of gases and vapours - Determination of the maximum explosion pressure |
| BS EN 13673-2-2005 | 气体和蒸气的最大爆炸压力和最大压升速率的测定.最大爆炸压升速率的测定 | Determination of maximum explosion pressure and the maximum rate of pressure rise of gases and vapours - Determination of the maximum rate of explosion pressure rise |
| BS EN 13787-2001 | 入口压力达100巴的气体压力调节器及相关安全装置的弹性体. | Elastomers for gas pressure regulators and associated safety devices for inlet pressures up to 100 bar |
| BS EN 13842-2004 | 燃油强制对流气体加热器.固定和可移动对流式空间加热器 | Oil fired forced convection air heaters - Stationary and transportable for space heating |
| BS EN 14208-2004 | 可移动式储气瓶.气体运输用容量最高达1000升的焊接的压力桶规范.设计和建造 | Transportable gas cylinders - Specification for welded pressure drums up to 1000 litre capacity for the transport of gases - Design and construction |
| BS EN 14382-2002 | 气压调节站和装置用安全设备.运行压力在100巴以下的气体安全关闭装置 | Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for operating pressure up to 100 bar |
| BS EN 14382-2005 | 气压调节站和装置用安全设备.进气口压力不超过100bar的气体安全截止装置 | Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar |
| BS EN 14387-2004 | 呼吸保护设备.气体过滤器和组合过滤器.要求、试验和标记 | Respiratory protective devices - Gas filter(s) and combined filter(s) - Requirements, testing, marking |
| BS EN 14412-2004 | 室内空气质量.气体和蒸气浓度测定用扩散样品.选择、使用和维护指南 | Indoor air quality - Diffusive samplers the determination of concentrations of gases and vapours - Guide for selection, use and maintenance |
| BS EN 14435-2004 | 呼吸保护设备.设计只与增压供氧一起使用的带半罩式面具的自持式开路压缩气体呼吸设备.要求、试验和标记 | Respiratory protective devices - Self-contained open-circuit compressed air breathing apparatus with half mask designed to be used with positive pressure only - Requirements, testing, marking |
| BS EN 14470-2-2006 | 防火安全存储柜.第2部分:压缩气体瓶用安全柜 | Fire safety storage cabinets — Part 2: Safety cabinets for pressurised gas cylinders |
| BS EN 14522-2005 | 测定气体和蒸气的自动点火温度 | Determination of the auto ignition temperature of gases and vapours |
| BS EN 14529-2005 | 呼吸保护装置.逃生专用包含由需求阀控制的正压呼吸器的带半截面罩的自持式开路压缩气体呼吸机 | Respiratory protective devices - Self-contained open-circuit compressed air breathing apparatus with half mask designed to include a positive pressure lung governed demand valve for escape purposes only |
| BS EN 14620-1-2006 | 工作温度0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制造的设计和生产.总则 | Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - General |
| BS EN 14620-2-2006 | 工作温度为0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制造的设计和生产.金属部件 | Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Metallic components |
| BS EN 14620-3-2006 | 工作温度0℃～-165℃的储存冷冻液态气体用垂直圆柱平底钢罐现场制造的设计和生产.混凝土部件 | Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Concrete components |
| BS EN 14620-4-2006 | 工作温度为0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制造的设计和生产.绝缘部件 | Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Insulation components |
| BS EN 14620-5-2006 | 工作温度0℃～-165℃液态气体冷冻储存用垂直圆柱平底钢罐现场制作的设计和生产.烘干、清洗和冷却测试 | Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Testing, drying, purging and cool-down |
| BS EN 14756-2006 | 燃烧气体和蒸气用限制氧含量(LOC)的测定 | Determination of the limiting oxygen concentration (LOC) for flammable gases and vapours |
| BS EN 14800-2007 | 使用气体燃料家用器具连接用波纹状安全金属软管组件 | Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels |
| BS EN 14866-2005 | 釉瓷和搪瓷.空气与气体和气体与气体热交换器用交流换热、上釉和包装的板材.规范 | Vitreous and porcelain enamels - Regenerative, enamelled and packed panels for air-gas and gas-gas heat exchangers - Specifications |
| BS EN 14912-2005 | 液化石油气体(LPG)设备和附件.汽缸周期性检查时液化石油气体(LPG)汽缸阀的检验和维护 | LPG equipment and accessories - Inspection and maintenance of LPG cylinder valves at time of periodic inspection of cylinders |
| BS EN 15158-2006 | 高级工业陶瓷.惰性气体高温下陶瓷混合料的机械特性.恒定振幅下疲劳特性的测定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of fatigue properties at constant amplitude |
| BS EN 15266-2007 | 建筑物中工作压力等于0.5bar的气体用不锈钢柔性波管工具 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| BS EN 15339-2-2007 | 热喷涂.热喷涂设备的安全要求.气体控制部件 | Thermal spraying - Safety requirements for thermal spraying equipment - Gas control units |
| BS EN 1555-1-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).总则 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - General |
| BS EN 1555-2-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).管道 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Pipes |
| BS EN 1555-3-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).配件 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Fittings |
| BS EN 1555-4-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).阀门 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Valves |
| BS EN 1555-5-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).系统的适用性 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Fitness for the purpose of the system |
| BS EN 1594-2000 | 燃气供应系统.最大工作压力超过16巴的气体管道.功能要求 | Gas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements |
| BS EN 161-2002 | 气体燃烧器和燃气器具自动关闭阀 | Automatic shut-off valves for gas burners and gas appliances |
| BS EN 1668-1997 | 焊接用料.非合金和细晶粒钢和钨极惰性气体保护用的焊条,焊丝和沉积物.分类 | Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non alloy and fine grain steels - Classification |
| BS EN 1755-2000 | 工业用卡车的安全.在潜在爆炸气体环境下的工作.在可燃气体,蒸气,潮湿和灰尘下使用 | Safety of industrial trucks - Operation in potentially explosive atmospheres - Use in flammable gas, vapour, mist and dust |
| BS EN 1797-1-1998 | 低温容器.气体/材料可混用性.氧可混用性 | Cryogenic vessels - Gas/material compatibility - Oxygen compatibility |
| BS EN 1797-2001 | 低温容器.气体/材料兼容性 | Cryogenic vessels - Gas/material compatibility |
| BS EN 1827-1999 | 呼吸保护装置.防气体或气体和颗粒或只防颗粒的无吸气阀带分离式过滤器的半面罩.要求、试验和标记 | Respiratory protective devices - Half masks without inhalation valves and with separable filters to protect against gases or gases and particles or particles only - Requirements, testing, marking |
| BS EN 1834-1-2000 | 往复式内燃发动机.用在潜在爆炸气体环境下发动机结构和设计安全要求.用于可燃气体和蒸气环境的II组发动机. | Reciprocating internal combustion engines - Safety requirements for design and construction of engines for use in potentially explosive atmospheres - Group II engines for use in flammable gas and vapour atmospheres - Part 1 : Group II engines for use in flammable gas and vapour atmospheres |
| BS EN 1834-2-2000 | 往复式内燃发动机.用在潜在爆炸气体环境下发动机结构和设计安全要求.用于地下工作时对沼气和/或可燃性尘土 | Reciprocating internal combustion engines - Safety requirements for design and construction of engines for use in potentially explosive atmospheres - Group I engines for use in underground workings susceptible to firedamp and/or combustible dust - Part 2: Group I engines for use in underground workings susceptible to firedamp and/or combustible dust |
| BS EN 1834-3-2000 | 往复式内燃发动机.用在潜在爆炸气体环境下发动机结构和设计安全要求.用于可燃灰尘环境下的II组发动机.第3部 | Reciprocating internal combustion engines - Safety requirements for design and construction of engines for use in potentially explosive atmospheres - Group II engines for use in flammable dust atmospheres - Part 3 : Group II engines for use in flammabel dust atmospheres |
| BS EN 1839-2004 | 气体和蒸气爆炸极限的测定 | Determination of explosion limits of gases and vapours |
| BS EN 1854-2006 | 气体燃烧器和燃气器具的压力敏感装置 | Pressure sensing devices for gas burners and gas burning appliances |
| BS EN 1892-2005 | 高级工业陶瓷.陶瓷复合材料在惰性气体中高温下的机械性能.抗拉性能测定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of tensile properties |
| BS EN 1894-2005 | 高级工业陶瓷.惰性气体环境中高温情况下陶瓷成分的机械特性.通过有凹槽试样的压力荷载测定剪切强度 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of shear strength by compression loading of notched specimens |
| BS EN 1911-1-1998 | 固定源发射.HCI的人工测定法.气体抽样 | Stationary source emissions - Manual method of determination of HCI - Sampling of gases |
| BS EN 1911-2-1998 | 固定源发射.HCI的人工测定法.气体混合物吸收 | Stationary source emissions - Manual method of determination of HCI - Gaseous compounds absorption |
| BS EN 1920-2000 | 可运输气瓶.压缩气体(不包括乙炔).灌装检验 | Transportable gas cylinders - Cylinders for compressed gases (excluding acetylene) - Inspection at time of filling |
| BS EN 1975-2000 | 便携气体钢瓶.容量由0,5升到150升(包括150升)的由无缝铝和铝合金制气体瓶的设计和结构规范. | Transportable gas cylinders - Specification for the design and construction of refillable transportable seamless aluminium and aluminium alloy gas cylinders of capacity from 0,5 litre up to 150 litre |
| BS EN 278-1991 | 采用压力达200毫巴可燃气体的家用器具膜片用橡胶材料规范 | Specification for rubber materials for diaphragms in domestic appliances using combustible gases up to 200 mbar |
| BS EN 279-1991 | 使用压力达200毫巴可燃气体的家用器具的动态密封件用均质橡胶材料规范 | Specification for homogenous rubber materials for dynamic seals in domestic appliances using combustible gases up to 200 mbar |
| BS EN 28846-1993 | 小船.电气装置.周围可燃气体引燃防护 | Small craft - Electrical devices - Protection against ignition of surrounding flammable gases |
| BS EN 291-1992 | 压力为200毫巴及其以下的家用可燃气体静态密封用橡胶密封件的材料规范 | Rubber seals - Static seals in domestic appliances for combustible gas up to 200 mbar - Specification for material |
| BS EN 334-1999 | 入口压力不大于100bar的气体压力调节器 | Gas pressure regulators for inlet pressures up to 100 bar |
| BS EN 405-2002 | 呼吸保护装置.防气体或防气体和颗粒的阀滤式半面罩.要求、试验和标记 | Respiratory protective devices - Valved filtering half masks to protect against gases or gases and particles - Requirements, testing, marking |
| BS EN 437-2003 | 试验气体.试验压力.器具分类 | Test gases - Test pressures - Appliance categories |
| BS EN 439-1994 | 焊接消耗用品.气体保护电弧焊和切割用气体 | Welding consumables - Shielding gases for arc welding and cutting |
| BS EN 440-1995 | 焊接消耗材料.非合金与细晶粒钢的气体保护金属电弧焊用丝状电极和熔积物.分类 | Welding consumables - Wire electrodes and deposits for gas shielded metal arc welding of non alloy and fine grain steels - Classification |
| BS EN 45544-1-2000 | 工作场所空气.有毒气体和蒸气的直接检测和直接富集测量用电气设施.一般要求和试验方法 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - General requirements and test methods |
| BS EN 45544-2-2000 | 工作场所空气.有毒气体和蒸气的直接检测和直接富集测量用电气设施.极限值区域中浓度测量用设备性能要求 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - Performance requirements for apparatus used for measuring concentrations in the region of limit values |
| BS EN 45544-3-2000 | 工作场所空气.有毒气体和蒸气的直接检测和直接富集测量用电气设施.大大超过极限值的浓度测量用设备性能要求 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - Performance requirements for apparatus used for measuring concentrations well above limit values |
| BS EN 45544-4-2000 | 工作场所空气.有毒气体和蒸气的直接检测和直接富集测量用电气设施.选用、安装、使用和维修指南 | Workplace atmospheres - Electrical apparatus used for the direct detection and direct concentration measurement of toxic gases and vapours - Guide for selection, installation, use and maintenance |
| BS EN 464-1994 | 防护服.对包括气溶液体和固体粒子的液体和气体化学物质的防护.试验方法.气体密封服的密封性测定(内压力试验 | Protective clothing - Protection against liquid and gaseous chemicals, including liquid aerosols and solid particles - Test method - Determination of leak-tightness of gas-tight suits (Internal Pressure Test) |
| BS EN 50194-2-2006 | 家庭房屋中可燃气体检测用电气设备.第2部分:娱乐车辆和类似经营场所中固定装置连续运转用电气设备.附加试验 | Electrical apparatus for the detection of combustible gases in domestic premises - Part 2: Electrical apparatus for continuous operation in a fixed installation in recreational vehicles and similar premises - Additional test methods and performance requirements |
| BS EN 50194-2000 | 家用易燃气体检测用电气设备.试验方法和性能要求 | Electrical apparatus for the detection of combustible gases in domestic premises - Test methods and performance requirements |
| BS EN 50216-2-2002 | 电力变压器和反应堆配件.液浸变压器和有存油器的反应堆用气体和油驱动的继电器 | Power transformers and reactor fittings - Gas and oil actuated relay for liquid immersed transformers and reactors with conservator |
| BS EN 50241-1-1999 | 可燃的或有毒性的气体和蒸气的检测用开路仪器规范.一般要求和试验方法 | Specification for open path apparatus for the detection of combustible or toxic gases and vapours - General requirements and test methods |
| BS EN 50241-2-1999 | 可燃的或有毒性的气体和蒸气的检测用开路仪器规范.可燃气体检测用仪器的性能要求 | Specification for open path apparatus for the detection of combustible or toxic gases and vapours - Performance requirements for apparatus for the detection of combustible gases |
| BS EN 50244-2000 | 家用易燃气体检测用电气设备.选用、安装、使用和维修指南 | Electrical apparatus for the detection of combustible gases in domestic premises - Guide on the selection, installation, use and maintenance |
| BS EN 50267-1-1999 | 失火情况下电缆的一般检验方法.电缆材料燃烧时产生的气体的检验.仪器 | Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Apparatus |
| BS EN 50267-2-1-1999 | 燃烧情况下电缆的一般检验方法.电缆材料燃烧时产生的气体的试验.程序.卤氢酸气体含量的测定 | Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Procedures - Determination of the amount of halogen acid gas - Determination of the amount of halogen acid gas |
| BS EN 50267-2-2-1999 | 燃烧情况下电缆的通用试验方法.电缆材料燃烧时产生的气体的试验.程序.通过测量Ph值和传导性测定材料燃烧产 | Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Procedures - Determination of degree of acidity of gases for materials by measuring pH and conductivity - Determination of degree of acidity of gases for materials by measuring pH and conductivity |
| BS EN 50267-2-3-1999 | 燃烧情况下电缆的一般检验方法.电缆材料燃烧时产生的气体的试验.程序.通过测量Ph值和传导率的加权平均值测 | Common test methods for cables under fire conditions - Tests on gases evolved during combustion of materials from cables - Procedures - Determination of degree of acidity of gases for cables by determination of the weighted average of pH and conductivity - Determination of degree of acidity of gases for cables by determination of the weighted average of pH and conductivity |
| BS EN 50270-1999 | 电磁兼容性.可燃气体、有毒气体或氧气检测和测量用电气设备 | Electromagnetic compatibility - Electrical apparatus for the detection and measurement of combustible gases, toxic gases or oxygen |
| BS EN 50270-2006 | 电磁兼容性.可燃气体、有毒气体或氧气的探测和测量用电气装置 | Electromagnetic compatibility - Electrical apparatus for the detection and measurement of combustible gases, toxic gases or oxygen |
| BS EN 50271-2002 | 检测和测量可燃气体、有毒气体和氧气的电气设备.使用软件和/或数字技术设备要求和试验 | Electrical apparatus for the detection and measurement of combustible gases, toxic gases or oxygen - Requirements and tests for apparatus using software and/or digital technologies |
| BS EN 50402-2005 | 易燃或有毒气体或蒸气或氧气的探测和测量用电气设备.混合气体探测系统的功能安全要求 | Electrical apparatus for the detection and measurement of combustible or toxic gases or vapours or of oxygen - Requirements on the functional safety of fixed gas detection systems |
| BS EN 60068-2-60-1996 | 环境试验.第2部分:试验方法.第60节:试验Ke:流动混合气体腐蚀试验 | Environmental testing - Test methods - Test Ke - Flowing mixed gas corrosion test |
| BS EN 60079-0-2004 | 爆炸性气体环境用电气设备.一般要求 | Electrical apparatus for explosive gas atmospheres - General requirements |
| BS EN 60079-0-2006 | 爆炸性气体环境用电气设备.一般要求 | Electrical apparatus for explosive gas atmospheres - General requirements |
| BS EN 60079-1-2004 | 爆炸性气体环境用电气设备.防火封装'd'型 | Electrical apparatus for explosive gas atmospheres - Flameproof enclosures 'd' |
| BS EN 60079-10-2003 | 爆炸性气体环境用电气设备.危险场所的分类 | Electrical apparatus for explosive gas atmospheres - Classification of hazardous areas |
| BS EN 60079-14-2003 | 爆炸性气体环境用电气设备.危险场所(矿井除外)中的电气装置 | Electrical apparatus for explosive gas atmospheres - Electrical installations in hazardous areas (other than mines) |
| BS EN 60079-15-2005 | 爆炸性气体环境用电气设备.n型保护电器装置的结构、试验和标记 | Electrical apparatus for explosive gas atmospheres - Part 15: Construction , test and marking of type of protection "n" electrical apparatus |
| BS EN 60079-18-2004 | 爆炸性气体环境用电气设备.包封"m"型防护电气设备的建造、试验和标记 | Electrical apparatus for explosive gas atmospheres - Construction , test and marking of type of protection encapsulation "m" electrical apparatus |
| BS EN 60079-2-2004 | 爆炸性气体环境用电气设备.压力封装型"p" | Electrical apparatus for explosive gas atmospheres - Pressurized enclosures "p" |
| BS EN 60079-25-2004 | 爆炸性气体环境用电气设备.本安型系统 | Electrical apparatus for explosive gas atmospheres - Intrinsically safe systems |
| BS EN 60079-26-2004 | 爆炸性气体环境用电气设备.II组IG类电气设备的制造、试验和标记 | Electrical apparatus for explosive gas atmospheres - Part 26: Construction, test and marking of Group Ⅱ Category 1 G electrical apparatus |
| BS EN 60079-27-2006 | 爆炸性气体环境用电气设备.现场总线本质安全原理(FISCO)和现场总线不易燃原理(FNICO) | Electrical apparatus for explosive gas atmospheres - Fieldbus intrinsically safe concept (FISCO) and fieldbus non-incendive concept (FNICO) |
| BS EN 60079-7-2003 | 爆炸性气体环境用电气设备.增安型"e" | Electrical apparatus for explosive gas atmospheres - Increased safety "e" |
| BS EN 60512-11-14-2003 | 电子设备用连接器.试验和测量.气候试验.流动单气体腐蚀试验 | Connectors for electronic equipment - Tests and measurements - Climatic tests - Flowing single gas corrosion test |
| BS EN 60512-11-7-2003 | 电子设备用连接器.试验和测量.流动混合气体腐蚀试验 | Connectors for electronic equipment - Tests and measurements - Flowing mixed gas corrosion test |
| BS EN 60567-2005 | 注油电气设备.游离和溶解气体分析用气体和油的取样.指南 | Oil-filled electrical equipment - Sampling of gases and of oil for analysis of free and dissolved gases - Guidance |
| BS EN 60599-1999 | 矿物油浸渍的电气设备.不溶自由气体分析说明指南 | Mineral oil-impregnated electrical equipment in service - Guide to the interpretation of dissolved and free gases analysis |
| BS EN 60749-7-2002 | 半导体器件.机械和气候试验方法.其他残余气体的内部湿气含量的测量和分析 | Semiconductor devices - Mechanical and climatic test methods - Internal moisture content measurement and the analysis of other residual gases |
| BS EN 60761-3-2004 | 连续监测放射性气态流出流物的设备.第3部分:放射性惰性气体监测仪的特殊要求 | Equipment for continuous monitoring radioactivity in gaseous effluents-Part 3:Specific requirements for radioactive noble gas monitors |
| BS EN 60974-8-2004 | 弧焊设备.焊接和等离子切割系统用气体控制台 | Arc welding equipment - Gas consoles for welding and plasma cutting systems |
| BS EN 61181-2007 | 填充矿物油的电气设备.溶解气体分析(DGA)用于电气设备工厂试验 | Mineral oil-filled electrical equipment - Application of dissolved gas analysis (DGA) to factory tests on electrical equipment |
| BS EN 61207-1-1994 | 气体分析器的性能说明.第1部分:概述 | Expression of performance of gas analyzers - General |
| BS EN 61207-2-1994 | 气体分析器性能说明.第2部分:气体中的氧(利用高温电化检测器) | Expression of performance of gas analyzers - Oxygen in gas (utilizing high-temperature electrochemical sensors) |
| BS EN 61207-3-2003 | 气体分析器的性能说明.顺磁氧分析器 | Expression of performance of gas analyzers - Paramagnetic oxygen analyzers |
| BS EN 61207-6-1994 | 气体分析仪性能.第6部分:光度分析仪 | Expression of performance of gas analyzers - Photometric analyzers |
| BS EN 61643-311-2002 | 低压电涌保护装置.气体放电管规范 | Low voltage surge protective devices - Specification for gas discharge tubes (GDT) |
| BS EN 61779-1-2000 | 可燃性气体的检测和测量用电气装置.一般要求和试验方法 | Electrical apparatus for the detection and measurement of flammable gases - General requirements and test methods |
| BS EN 61779-2-2000 | 可燃性气体的检测和测量用电气装置.指示空气中甲烷含量达到体积分率为5%时I组装置的性能要求 | Electrical apparatus for the detection and measurement of flammable gases - Performance requirements for group I apparatus indicating a volume fraction up to 5% methane in the air |
| BS EN 61779-3-2000 | 可燃性气体的检测和测量用电气装置.指示空气中甲烷含量达到体积分率为100%时I组装置的性能要求 | Electrical apparatus for the detection and measurement of flammable gases - Performance requirements for group I apparatus indicating a volume fraction up to 100% methane in air |
| BS EN 61779-4-2000 | 可燃性气体的检测和测量用电气装置.指示低爆炸极限达到体积分率为100%时II组装置的性能要求 | Electrical apparatus for the detection and measurement of flammable gases - Performance requirements for group II apparatus indicating a volume fraction up to 100% lower explosive limit |
| BS EN 61779-5-2000 | 可燃性气体的检测和测量用电气装置.指示体积分率达到100%时II组装置的性能要求 | Electrical apparatus for the detection and measurement of flammable gases - Performance requirements for group II apparatus indicating a volume fraction up to 100% gas |
| BS EN 62086-1-2005 | 爆炸性气体环境用电气设备.电阻轨道加热.一般和试验要求 | Electrical apparatus for explosive gas atmospheres - Electrical resistance trace heating - General and testing requirements |
| BS EN 62086-2-2005 | 爆炸性气体环境用电气设备.电阻轨道加热.设计、安装和维护的应用指南 | Electrical apparatus for explosive gas atmospheres - Electrical resistance trace heating - Application guide for design, installation and maintenance |
| BS EN 62259-2004 | 含碱性或其他非酸性电解质的蓄电池和蓄电池组.部分气体复合的镍镉柱状二次单电池 | Secondary cells and batteries containing alkaline or other non-acid electrolytes - Nickel-cadmium prismatic secondary single cells with partial gas recombination |
| BS EN 62271-203-2004 | 高压开关设备和控制设备.额定电压高于52KV的气体绝缘金属封闭式开关设备 | High-voltage switchgear and controlgear - Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV |
| BS EN 676-2003 | 气体燃料用自动强制送风燃烧器 | Automatic forced draught burners for gaseous fuels |
| BS EN 682-2002 | 弹性密封件.运送气体和液态碳氢化合物的管件及配件中用的密封件的材料要求 | Elastomeric seals - Materials requirements for seals used in pipes and fi ttings carrying gas and hydrocarbon fluids |
| BS EN 717-2-1995 | 木质板材.甲醛释放量的测定.用气体分析法测定甲醛释放量 | Wood-based panels - Determination of formaldehyde release - Formaldehyde release by the gas analysis method |
| BS EN 720-1-1999 | 可移动的储气瓶.气体和气体混合物.纯燃气特性 | Transportable gas cylinders - Gases and gas mixtures - Properties of pure gases |
| BS EN 720-2-1997 | 可移动的储气瓶.气体和气体混合物.气体和气体混合物的易燃性和氧化性的测定 | Transportable gas cylinders - Gases and gas mixtures - Determination of flammability and oxidizing ability of gases and gas mixtures |
| BS EN 737-1-1998 | 医疗气体管道系统.压缩医疗气体用和真空用终端设备 | Medical gas pipeline systems - Terminal units for compressed medical gases and vacuum |
| BS EN 737-3-2000 | 医疗用气体管道系统.压缩医疗气体和真空管道 | Medical gas pipeline systems - Pipelines for compressed medical gases and vacuum |
| BS EN 737-4-1998 | 医疗气体管道系统.麻醉气体净化系统的端部设备 | Medical gas pipeline systems - Terminal units for anaesthetic gas scavenging systems |
| BS EN 738-3-1999 | 医疗用气体的压力调节器.与气瓶阀组合的压力调节器 | Pressure regulators for use with medical gases - Pressure regulators integrated with cylinder valves |
| BS EN 738-4-1999 | 医疗用气体的压力调节器.医疗设备用低压力调节器 | Pressure regulators for use with medical gases - Low-pressure regulators intended for incorporation into medical equipment |
| BS EN 739-1998 | 医疗用气体设备的低压软管组件 | Low-pressure hose assemblies for use with medical gases |
| BS EN 746-3-1997 | 工业热加工设备.环境气体产生和使用的安全要求 | Industrial thermoprocessing equipment - Safety requirements for the generation and use of atmosphere gases |
| BS EN 758-1997 | 焊接用料.带有和不带非合金钢及细粒钢气体保护的金属电弧焊接用管状芯焊条.分类 | Welding consumables - Tubular cored electrodes for metal arc welding with and without a gas shield of non-alloy and fine grain steels - Classification |
| BS EN 838-1996 | 工作场所的环境.测定气体和水蒸汽用的扩散取样器.要求和试验方法 | Workplace atmospheres - Diffusive samplers for the determination of gases and vapours - Requirements and test methods |
| BS EN 943-1-2002 | 耐液体和气体药液、气溶胶和固体粒子腐蚀的防护服.通风和不通风的气体密封(类型1)和非气体密封(类型2)化学 | Protective clothing against liquid and gaseous chemicals, aerosols and solid particles - Performance requirements for ventilated and non-ventilated "gas-tight" (Type 1) and "non-gas-tight" (Type 2) chemical protective suits |
| BS EN 943-2-2002 | 耐液体和气体药液、气溶胶和固体粒子腐蚀的防护服.消防队 (ET)用气密性化学防护服的性能要求 | Protective clothing against liquid and gaseous chemicals, aerosols and solid particles - Performance requirements for "gas-tight" (Type 1) chemical protective suits for emergency teams (ET) |
| BS EN 993-4-1995 | 致密成型耐火制品的试验方法.第4部分:气体渗透率测定 | Methods of test for dense shaped refractory products - Determination of permeability to gases |
| BS EN ISO 10156-2-2006 | 储气瓶.气体和气体混合物.毒性和腐蚀性气体和气体混合物的氧化强度测定 | Gas cylinders - Gases and gas mixtures - Determination of oxidizing ability of toxic and corrosive gases and gas mixtures |
| BS EN ISO 10439-2002 | 石油、化学和气体工业.离心压缩机 | Petroleum, chemical and gas service industries - Centrifugal compressors |
| BS EN ISO 10442-2003 | 石油、化学和气体工业.整体封装齿轮传动离心空气压缩机 | Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors |
| BS EN ISO 105-G02-1997 | 纺织品.色牢度试验.第G02部分:耐燃烧气体烟雾色牢度 | Textiles - Tests for colour fastness - Colour fastness to burnt-gas fumes |
| BS EN ISO 10524-1-2006 | 医用气体设备用的压力调节器和带流量计的压力调节器 | Pressure regulators for use with medical gases - Pressure regulators and pressure regulators with flow-metering devices |
| BS EN ISO 10524-2-2007 | 医用气体的压力调节器.歧管和线管压力调节器 | Pressure regulators for use with medical gases - Manifold and line pressure regulators |
| BS EN ISO 10882-1-2001 | 焊接和有关过程的卫生和安全.操作者呼吸区域的空气悬浮颗粒和气体的取样.空气悬浮颗粒取样 | Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator's breathing zone - Sampling of airborne particles |
| BS EN ISO 10882-2-2000 | 焊接及相关工艺的卫生与安全.操作人员呼吸区域内空气中悬浮颗粒及气体的抽样.气体的抽样 | Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator's breathing zone - Sampling of gases |
| BS EN ISO 11114-4-2007 | 运输储气瓶.储气瓶和阀门材料与盛装气体的兼容性.选择耐氢脆金属材料的试验方法 | Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Test methods for selecting metallic materials resistant to hydrogen embrittlement |
| BS EN ISO 1183-3-1999 | 塑料.非泡沫塑料密度测定方法.气体比重瓶测量法 | Plastics - Methods for determining the density of non-cellular plastics - Gas pyknometer method |
| BS EN ISO 12209-3-2001 | 气瓶.压缩可呼吸气体用气瓶阀的出口连接.230巴阀门转接器 | Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air - Adaptor for 230 bar valves |
| BS EN ISO 12569-2001 | 建筑物的隔热性.建筑物中空气流通性的测定.示踪气体稀释法 | Thermal insulation in buildings - Determination of air change in buildings - Tracer gas dilution method |
| BS EN ISO 13340-2001 | 可运输燃气瓶.不可再填充气体的钢气瓶的阀门.规范和原型件试验 | Transportable gas cylinders - Cylinder valves for non-refillable cylinders - Specification and prototype testing |
| BS EN ISO 13631-2002 | 石油和天然气工业.组合的往复式气体压缩机 | Petroleum and natural gas industries - Packaged reciprocating gas compressors |
| BS EN ISO 14344-2005 | 焊接和有关处理.焊剂和气体保护弧焊法.消耗品的采购导则 | Welding and allied processes - Flux and gas shielded electrical welding processes - Procurement guidelines for consumables |
| BS EN ISO 15011-1-2002 | 焊接和有关加工工艺中的健康和安全性.电弧焊接产生的烟尘和气体的实验室取样方法.排放率测定和颗粒烟尘分析 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Determination of emission rate and sampling for analysis of particulate fume |
| BS EN ISO 15011-2-2003 | 焊接和相关工艺的卫生和安全.电弧焊产生的烟和气体取样的实验室法.除臭氧外的气体排放率的测定 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Determination of emission rates of gases, except ozone |
| BS EN ISO 15616-3-2003 | 高质量焊接和切割用CO2激光束机的验收试验.气体流量和压力测量仪的校正 | Acceptance tests for CO2- laser beam machines for high quality welding and cutting - Calibration of instruments for measurement of gas flow and pressure |
| BS EN ISO 16834-2007 | 焊接消耗品.高强度钢气体保护电弧焊用焊丝电极、焊丝、焊条和沉积金属.分类 | Welding consumables - Wire electrodes, wires, rods and deposits for gas-shielded arc welding of high strength steels - Classification |
| BS EN ISO 17633-2006 | 焊接消耗品.不锈钢和耐热钢的气体保护和非气体保护金属弧焊用药芯电极和焊条.分类 | Welding consumables - Tubular cored electrodes and rods for gas shielded and non-gas shielded metal arc welding of stainless and heat-resisting steels - Classification |
| BS EN ISO 17634-2006 | 焊接消耗品.抗蠕变钢的气体保护金属极电弧焊用药芯焊条.分类 | Welding consumables - Tubular cored electrodes for gas shielded metal arc welding of creep-resisting steels - Classification |
| BS EN ISO 18276-2006 | 焊料.高强度钢的气体保护和非气体保护金属极电弧焊用药芯电极.分类 | Welding consumables - Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high-strength steels - Classification |
| BS EN ISO 18757-2006 | 精细陶瓷(高级陶瓷、高级工业陶瓷).利用BET法的气体吸收率测定陶瓷粉末的比表面积 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of specific surface area of ceramic powders by gas adsorption using the BET method |
| BS EN ISO 21647-2004 | 医用电气设备.呼吸气体监测器的基本安全和性能的特殊要求 | Medical electrical equipment - Particular requirements for the basic safety and essential performance of respiratory gas monitors |
| BS EN ISO 21969-2006 | 同医疗气体设备一起使用的高压挠性连接件 | High-pressure flexible connections for use with medical gas systems |
| BS EN ISO 2556-2001 | 塑料.在大气压力下薄膜和薄板的气体透过率的测定.测压法 | Plastics - Determination of the gas transmission rate of films and thin sheets under atmospheric pressure - Manometric method |
| BS EN ISO 6141-2006 | 气体分析.校准气体和气体混合物的合格证书要求 | Gas analysis - Requirements for certificates for calibration gases and gas mixtures |
| BS EN ISO 6142-2006 | 气体分析.校准气体混合物的制备.称重法 | Gas analysis - Preparation of calibration gas mixtures - Gravimetric method |
| BS EN ISO 6143-2006 | 气体分析.测定和检验校准气体混合物成分用比较法 | Gas analysis - Comparison methods for determining and checking the composition of calibration gas mixtures |
| BS EN ISO 6144-2006 | 气体分析.校准气体混合物的制备.静态测定体积法 | Gas analysis - Preparation of calibration gas mixtures - Static volumetric method |
| BS EN ISO 6529-2001 | 防护服.对化学物质的防护.防护服材料防液体和气体渗透性的测定 | Protective clothing - Protection against chemicals - Determination of resistance of protective clothing materials to permeation by liquids and gases |
| BS EN ISO 6551-1983 | 石油液体和气体.动态测量的精确性可靠性.电脉冲数据和/或电子脉冲数据的电缆传输 | Petroleum liquids and gases - Fidelity and security of dynamic measurement - Cabled transmission of electric and/or electronic pulsed data |
| BS EN ISO 7235-2003 | 声学.管道消音器和气体终端设备的实验室测量步骤.插入损失、流动噪声和总压损失 | Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss |
| BS EN ISO 7396-1-2007 | 医用气体管道系统.压缩医用气体和真空用管道系统 | Medical gas pipeline systems - Pipeline systems for compressed medical gases and vacuum |
| BS EN ISO 7396-2-2007 | 医用气体管道系统.麻醉用气体净化处理系统 | Medical gas pipeline systems - Anaesthetic gas scavenging disposal systems |
| BS EN ISO 9300-2005 | 用临界流量文丘里喷嘴测定气体流量 | Measurement of gas flow by means of critical flow Venturi nozzles |
| BS EN ISO 9360-1-2000 | 麻醉和呼吸设备.对人体呼吸气体进行加湿的热气和湿气交换器(HMEs).与最小潮量为250 ml的设备一起使用的热气 | Anaesthetic and respiratory equipment - Heat and moisture exchangers (HMEs) for humidifying respired gases in humans - HMEs for use with minimum tidal volumes of 250 ml |
| BS EN ISO 9360-2-2002 | 麻醉和呼吸设备.使人体呼吸的气体变湿润用的热和潮气交换器(HMEs).气管造口病人用最小潮流量为250ml的热和 | Anaesthetic and respiratory equipment - Heat and moisture exchangers (HMEs) for humidifying respired gases in humans - HMEs for use with tracheostomized patients having minimum tidal volumes of 250 ml |
| BS EN ISO 9692-1-2003 | 焊接和相关工艺.接缝制备的建议.钢的手动金属电弧焊、气体保护金属电弧焊、气焊、TIG焊接和束焊 | Welding and allied processes - Recommendations for joint preparation - Manual metal-arc welding, gas-shielded metal-arc welding, gas welding, TIG welding and beam welding of steels |
| BS EN ISO 9692-3-2001 | 焊接和相关工艺.接头的准备.铝及其合金的金属极惰性气体保护焊和钨极惰性气体保护焊 | Welding and allied processes - Joint preparation - Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys |
| BS IEC 60079-1997 | 易爆气体氛围用电器.第19部分:易爆氛围(矿井和爆炸的除外)用电器的维护和翻修 | Electrical apparatus for explosive gas atmospheres. Repair and overhaul for apparatus used in explosive atmospheres (other than mines or explosives) |
| BS IEC 60761-3-2002 | 气态排放物放射性的连续监测设备.放射性惰性气体监测器的特殊要求 | Equipment for continuous monitoring of radioactivity in gaseous effluents - Specific requirements for radioactive noble gas monitors |
| BS ISO 10396-2007 | 固定源排放.永久安装监测系统用自动测量气体排放浓度的抽样 | Stationary source emissions - Sampling for the automated determination of gas emission concentrations for permanently-installed monitoring systems |
| BS ISO 11195-1996 | 医疗用气体混合器.独立气体混合器 | Gas mixers for medical use - Stand-alone gas mixers |
| BS ISO 11338-1-2003 | 固定源辐射.气体和粒子相多环芳香烃的测定.取样 | Stationary source emissions - Determination of gas and particle-phase polycyclic aromatic hydrocarbons - Sampling |
| BS ISO 14064-1-2006 | 温室气体.量化和报告温室气体排放量和消除的组织水平指南的规范 | Greenhouse gases - Specification with guidance at the organization level for quantification and reporting of greenhouse gas emissions and removals |
| BS ISO 14064-2-2006 | 温室气体.量化、监视和报告温室气体排放量减少或消除强化的设计水平指南的规范 | Greenhouse gases - Specification with guidance at the project level for quantification, monitoring and reporting of greenhouse gas emission reductions or removal enhancements |
| BS ISO 14064-3-2006 | 温室气体.温室气体确定的证实和验证指南的规范 | Greenhouse gases - Specifications with guidance for the validation and verification of greenhouse gas assertions |
| BS ISO 14065-2007 | 温室气体.认证或承认的其他形式用温室气体证实和验证机构要求 | Greenhouse gases - Requirements for greenhouse gas validation and verification bodies for use in accreditation or other forms of recognition |
| BS ISO 14520-1-2006 | 气体灭火系统.物理性能和系统设计.一般要求 | Gaseous fire-extinguishing systems - Physical properties and system design - General requirements |
| BS ISO 14520-10-2006 | 气体灭火系统.物理性能和系统设计.HFC 23灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - HFC 23 extinguishant |
| BS ISO 14520-11-2006 | 气体灭火系统.物理性能和系统设计.HFC 236fa灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - HFC 236fa extinguishant |
| BS ISO 14520-12-2006 | 气体灭火系统.物理性能和系统设计.IG-01灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - IG-01 extinguishant |
| BS ISO 14520-13-2006 | 气体灭火系统.物理性能和系统设计.IG-100灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - IG-100 extinguishant |
| BS ISO 14520-14-2006 | 气体灭火系统.物理性能和系统设计.IG-55灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - IG-55 extinguishant |
| BS ISO 14520-15-2006 | 气体灭火系统.物理性能和系统设计.IG-541灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - IG-541 extinguishant |
| BS ISO 14520-2-2006 | 气体灭火系统.物理性能和系统设计.CF3I灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - CF3I extinguishant |
| BS ISO 14520-3-2001 | 气体灭火系统.物理性能和系统设计.FC-2-1-8灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - FC-2-1-8 extinguishant |
| BS ISO 14520-4-2001 | 气体灭火系统.物理性能和系统设计.FC-3-1-10灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - FC-3-1-10 extinguishant |
| BS ISO 14520-5-2006 | 气体灭火系统.物理性能和系统设计.FK-5-1-12灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - FK-5-1-12 extinguishant |
| BS ISO 14520-6-2006 | 气体灭火系统.物理性能和系统设计.HCFCA混合灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - HCFC blend A extinguishant |
| BS ISO 14520-7-2001 | 气体灭火系统.物理性能和系统设计.HCFC124混合灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - HCFC Blend 124 extinguishant |
| BS ISO 14520-8-2006 | 气体灭火系统.物理性能和系统设计.HFC 125灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - HFC 125 extinguishant |
| BS ISO 14520-9-2006 | 气体灭火系统.物理性能和系统设计.HFC 227ea灭火剂 | Gaseous fire-extinguishing systems - Physical properties and system design - HFC 227ea extinguishant |
| BS ISO 14531-1-2003 | 塑料管道和配件.气体燃料输送用交联聚乙烯(PE-X)管道系统.米制系列.管规范 | Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Pipes |
| BS ISO 14531-2-2006 | 塑料管道和配件.气体燃料运输用交联聚乙烯管道系统.米制系列.规范.热熔连接用配件.熔焊连接 | Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Fittings for heat-fusion jointing |
| BS ISO 14531-3-2006 | 塑料管道和配件.气体燃料运输用交联聚乙烯管道系统.米制系列.规范.机械连接用配件(包括PE-X/金属转换) | Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Fittings for mechanical jointing (including PE-X/metal transitions) |
| BS ISO 14531-4-2006 | 塑料管道和配件.气体燃料运输工具用交联聚乙烯(PE-X)管道系统.米制系列.规范.系统设计和安装指南 | Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - System design and installation guidelines |
| BS ISO 14661-2000 | 工业用热涡轮机(蒸气涡轮机、气体膨胀式轮机).一般要求 | Thermal turbines for industrial applications (steam turbines, gas expansion turbines) - General requirements |
| BS ISO 14912-2003 | 气体分析.气体混合成分数据的转换 | Gas ananlysis - Conversion of gas mixture composition data |
| BS ISO 1496-3-1995 | 货运集装箱系列1.规范和试验.第3部分:液体、气体和加压散料用罐式集装箱 | Series 1 Freight containers - Specification and testing - Tank containers for liquids, gases and pressurized dry bulk |
| BS ISO 15105-1-2002 | 塑料.薄模和薄模纸.用压差法测定气体穿透率 | Plastics - Film and sheeting - Determination of gas-transmission rate - Differential-pressure method |
| BS ISO 15105-2-2003 | 塑料.薄膜和片材.气体传输率的测定.等压法 | Plastics - Film and sheeting - Determination of gas-transmission rate - Equal-pressure method |
| BS ISO 15303-2001 | 动植物脂肪和油.通过气体色谱法(GC)/质谱(MS)法对挥发性有机杂质的检测和识别 | Animal and vegetable fats and oils - Detection and identification of a volatile organic contaminent by GC/MS |
| BS ISO 15741-2002 | 油漆和清漆.岸上和近海铺设的无腐蚀气体钢管道内侧的减小摩擦涂层 | Paints and varnishes - Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases |
| BS ISO 15796-2005 | 气体分析.分析偏差的调查和处理 | Gas analysis - Investigation and treatment of analytical bias |
| BS ISO 15859-13-2004 | 航空航天系统.航天系统.流体性能、抽样和试验方法.呼吸气体 | Aerospace series - Space systems - Fluid characteristics, sampling and test methods - Breathing air |
| BS ISO 15860-2006 | 航天系统.气体污染.现场试验测量方法 | Space systems - Gas contamination - Measurement methods for field tests |
| BS ISO 15901-1-2006 | 用水银孔率法和气体吸附法测定固体材料的孔隙尺寸分布和孔隙率.水银孔率法 | Pore size distribution and porosity of solid materials by mercury porosimetry and gas adsorption - Mercury porosimetry |
| BS ISO 15901-2-2007 | 用水银孔率法和气体吸附法测定固体材料孔径分布和孔隙率.用气体吸附法分析介孔和微孔 | Pore size distribution and porosity of solid materials by mercury porosimetry and gas adsorption - Analysis of mesopores and macropores by gas adsorption |
| BS ISO 15901-3-2007 | 用水银孔率法和气体吸附法测定固体材料孔隙尺寸分布和孔隙率.用气体吸附法分析微孔 | Pore size distribution and porosity of solid materials by mercury porosimetry and gas adsorption - Analysis of micropores by gas adsorption |
| BS ISO 16183-2003 | 重型机车.未处理排气的气体排放测量和瞬变试验条件下用部分流体稀释系统测量粒子排放 | Heavy duty engines - Measurement of gaseous emissions from raw exhaust gas and of particulate emissions using partial flow dilution systems under transient test conditions |
| BS ISO 16664-2004 | 气体分析.校正气体和气体混合物的处理.指南 | Gas analysis - Handling of calibration gases and gas mixtures - Guidelines |
| BS ISO 17053-2005 | 钢和铁.氧测定.经惰性气体熔化后的红外线方法 | Steel and iron - Determination of oxygen - Infrared method after fusion under inert gas |
| BS ISO 19703-2006 | 毒性气体生成和分析.实验室燃烧中物质生成、当量比和燃烧效率的计算 | Generation and analysis of toxic gases - Calculation of species yields, equivalence ratios and combustion efficiency in experimental fires |
| BS ISO 21010-2004 | 低温容器.气体/材料兼容性 | Cryogenic vessels - Gas/materials compatibility |
| BS ISO 21687-2007 | 铝生产用含碳材料.以氮作为分析气体的气体比重测量法(测定体积的)测定密度.固体材料 | Carbonaceous materials used in the production of aluminium - Determination of density by gas pyknometry (volumetric) using helium as the analysis gas - Solid materials |
| BS ISO 24431-2007 | 储气瓶.压缩气体和液化气体(乙炔除外)用储气瓶.灌装检验 | Gas cylinders - Cylinders for compressed and liquefied gases (excluding acetylene) - Inspection at the time of filling |
| BS ISO 4524-2-2000 | 金属镀层.金及金合金电镀层的试验方法.混合流动气体(MFG)环境试验 | Metallic coatings - Test methods for electrodeposited gold and gold alloy coatings - Mixed flowing gas (MFG) environmental tests |
| BS ISO 5024-1999 | 石油液体和液化石油气体.测量.标准参照条件 | Petroleum liquids and liquefied petroleum gases - Measurement - Standard reference conditions |
| BS ISO 6145-1-2004 | 气体分析.动态容量法制备标定用混合气体.校准方法 | Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Methods of calibration |
| BS ISO 6145-10-2002 | 气体分析.用动态容积法制备校验气体混合物.渗透法 | Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Permeation method |
| BS ISO 6145-11-2006 | 气体分析.用动态容量法预备标定用混合气体.电化学产生 | Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Electrochemical generation |
| BS ISO 6145-2-2001 | 气体分析.标定用混合气体的制备.动态容量法.容积计量泵 | Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Volumetric pumps |
| BS ISO 6145-4-2005 | 气体分析.用动态容量法制备标定用混合气体.持续喷射器注入法 | Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Continuous syringe injection method |
| BS ISO 6145-5-2001 | 气体分析.标定用混合气体的制备.动态容量法.毛细管校正装置 | Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Capillary calibration devices |
| BS ISO 6145-6-2003 | 气体分析.用动态容量法制备标定用混合气体.临界孔 | Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Critical orifices |
| BS ISO 6145-7-2001 | 气体分析.标定用混合气体的制备.动态容量法.热物流控制器 | Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Thermal mass-flow controllers |
| BS ISO 6145-8-2005 | 气体分析.用动态容积法制备标定用气体混合物.扩散法 | Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Diffusion method |
| BS ISO 6145-9-2002 | 气体分析.用动态容量法制备标定用混合气体.饱和法 | Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Saturation method |
| BS ISO 7504-2002 | 气体分析.词汇 | Gas analysis - Vocabulary |
| BS ISO 8085-2-2001 | 供应气体燃料的聚乙烯管上使用的聚乙烯管件.米制系列.规范.熔接用的、通过加热器具进行的套筒熔融用的及与 | Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels - Metric series - Specifications - Spigot fittings for butt fusion, for socket fusion using heated tools and for use with eletrofusion fittings |
| BS ISO 8573-6-2003 | 压缩空气.气体污染物含量的试验方法 | Compressed air - Test methods for gaseous contaminant content |
| BS ISO/TS 16922-2002 | 天然气.添味气体的导则 | Natural gas - Guidelines for odorizing gases |
| BS PAS 42-2002 | 确认装饰性可燃效应气体燃烧效果的试验方法 | Method of test for establishing the efficiency of decorative fuel effect gas fires |
| DD 220-1994 | 土壤质量.矿物油含量的测定.红外线光谱分析方法和气体色谱方法 | Soil quality. Determination of mineral oil content. Method by infrared spectrometry and gas chromatographic method |
| FD X 31-611-1-1997 | 土壤质量.污染程度监测和定性分析.土壤筛选监测时使用的现场土壤气体分析一般指南 | SOIL QUALITY. POLLUTION DETECTION AND CHARACTERIZATION METHODS. GENERAL GUIDE FOR SOIL GAS ANALYSES ON SITE USED IN LAND SCREENING. |
| KIT 105-2002 | 气体灭火装置 | Gaseous fire-extinguishing set |
| PD 6574-1994 | 气体燃料在型号试验过程中从燃烧设备里散发的物质测定 | Determination of emissions from appliances burning gaseous fuels during type-testing |
| PD CR 14244-2001 | 木材和木基产品的耐久性.经处理的木材在使用时排放到环境中的气体测量的推荐方法 | Durability of wood and wood based products. Recommendations for measurement of emissions to the environment from treated wood in service |
| PD IEC 60079-20-2000 | 易爆气体环境的电气设备.电气设备使用的相关易燃气体和蒸气的数据 | Electrical apparatus for explosive gas atmospheres. Data for flammable gases and vapours, relating to the use of electrical apparatus |
| PD IEC TR 61010-3-043-2002 | 测量、控制和实验室用电气设备的安全要求.IEC 61010-2-043:1997<医疗材料处理和实验室试验用热空气或热惰性 | Safety requirements for electrical equipment for measurement, control, and laboratory use. Conformity verification report for IEC 61010-2-043:1997. Particular requirements for dry heat sterilizers using either hot air or hot inert gas for treatment of medical materials and for laboratory processes |
| TH 42065-2000 | 易燃气体用电气设备.法规、试验和认证要求的国际检验报告 | Electrical Equipment for Flammable Atmospheres - An international survey of regulations, tests and certification requirements |
| TH 42079-1997 | 气体装置的CE标志 | CE Marking of Gas Equipment |
| 编号 | 中文名称 | 英文名称 |