| 编号 | 中文名称 | 英文名称 |
|---|
| EN 10246-1-1996
| 钢管的无损检测 第1部分：证明液压密封性用无缝和焊接铁磁钢管(埋弧焊除外)的自动电磁检验
| Non destructive testing of steel tubes - Part 1: Automatic electromagnetic testing of seamless and welded (except submerged arc welded) ferromagnetic steel tubes for verification of hydraulic leak-tightness
|
| EN 10246-2-2000
| 钢管的无损检测 第2部分：证明液压密封性用无缝和焊接奥氏体和奥氏体铁素体钢管（埋弧焊除外） 的自动涡流
| Non-destructive testing of steel tubes - Part 2: Automatic eddy current testing of seamless and welded (except submerged arc-welded) austenitic and austenitic-ferritic steel tubes for verification of hydraulic leak-tightness
|
| EN 1027-2000
| 门窗 水密封性 试验方法
| Windows and doors - Watertightness - Test method
|
| EN 1053-1995
| 塑料管道系统 无压力情况下使用的热塑管道系统 水密封性的试验方法
| Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness
|
| EN 1119-1996
| 塑料管道系统 玻璃增强热固塑料管和配件用接头 挠性和还原接合接头密封性和耐损伤性试验方法
| Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of flexible and reduced-articulation joints
|
| EN 116205*EN 116206*EN 116207-1995
| 空白详细规范：气密密封继电器 用于严酷静电环境条件(116025) 用于严酷动态环境条件(116206 ) 用于严酷
| Blank detail specification: Hermetically sealed relays - For severe static environmental conditions (116205) - For severe mobile environmental conditions (116206) - For severe airborne environmental conditions (116207)
|
| EN 116303-1993
| 空白详细规范：机电有或无继电器 经质量评定的重载继电器(气密密封5A至25A)
| Blank detail specification- Electromechanical all-or-nothing- Heavy load relays of assessed quality (hermetically sealed, 5 A to 25 A)
|
| EN 1229-1996
| 塑料管道系统 玻璃增强热固性塑料管 验证短期内部压力下墙的密封性试验方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure
|
| EN 12365-1-2003
| 建筑五金件 门、窗、百叶窗和幕墙用密封垫和挡风条 第1部分：性能要求和分类
| Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 1: Performance requirements and classification
|
| EN 12365-2-2003
| 建筑五金件 门、窗、百叶窗和幕墙用密封垫和挡风条 第2部分：线性压力试验方法
| Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 2: Linear compression force test methods
|
| EN 12365-3-2003
| 建筑五金件 门、窗、百叶窗和幕墙用密封垫和挡风条 第3部分：偏移回复试验方法
| Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 3: Deflection recovery test method
|
| EN 12365-4-2003
| 建筑五金件 门、窗、百叶窗和幕墙用密封垫和挡风条 第4部分：加速老化后复原试验方法
| Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 4: Recovery after accelerated ageing test method
|
| EN 12385-7-2002
| 钢丝绳 安全性 第7部分：矿井用密封钢丝绳
| Steel wire ropes - Safety - Part 7: Locked coil ropes for mine shafts
|
| EN 12385-9-2002
| 钢丝绳 安全性 第9部分：载人索道设备用承载密封钢丝绳
| Steel wire ropes - Safety - Part 9: Locked coil carrying ropes for cableway installations designed to carry persons
|
| EN 12690-1999
| 生物技术 轴密封的性能标准
| Biotechnology - Performance criteria for shaft seals
|
| EN 12756-2000
| 机械密封 主要尺寸、标识和材料编码
| Mechanical seals - Principal dimensions, designation and material codes
|
| EN 1277-1996
| 塑料管道系统 地下无压用热塑管道系统 弹性密封环型接头密封性试验方法
| Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints
|
| EN 1279-4-2002
| 建筑玻璃 隔离玻璃装置 第4部分：边缘密封物理特性的试验方法
| Glass in building - Insulating glass units - Part 4: Methods of test for the physical attributes of edge seals
|
| EN 12928-2000
| 总容积为17升至230升的钢桶用插入法兰型密封系统
| Inserted flange type closure systems for steel drums with a total capacity of 17 l to 230 l
|
| EN 13007-1999
| 钢桶 标称容积为20升到60升的带固定盖（密封盖）的桶
| Steel drums - Non-removable head (tight head) drums with a nominal capacity of 20 l to 60 l
|
| EN 13090-2000
| 建筑物中气体管道螺纹接头再密封方法
| Means for resealing threaded joints of gas pipework in buildings
|
| EN 13184-2001
| 无损检测 密封试验 变压法
| Non-destructive testing - Leak testing - Pressure change method
|
| EN 13185-2001
| 无损检测 密封试验 示踪气体法
| Non-destructive testing - Leak testing - Tracer gas method
|
| EN 13192-2001
| 无损检测 密封试验 气体标准漏出物校准
| Non destructive testing - Leak testing - Calibration of reference leaks for gases
|
| EN 1330-8-1998
| 无损检测 术语 第8部分：密封性检测用术语
| Non-destructive testing - Terminology - Part 8: Terms used in leak tightness testing
|
| EN 13880-1-2003
| 热接合密封剂 第1部分：25℃下的密度测定的试验方法
| Hot applied joint sealants - Part 1: Test method for the determination of density at 25℃
|
| EN 13880-10-2003
| 热接合密封剂 第10部分：连续延伸和压缩之后附着力和粘合力测定的试验方法
| Hot applied joint sealants - Part 10: Test method for the determination of adhesion and cohesion following continuous extension and compression
|
| EN 13880-11-2003
| 热接合密封剂 第11部分：功能试验中所用的沥青试验块的制备和与沥青路面相容性测定的试验方法
| Hot applied joint sealants - Part 11: Test method for the preparation of asphalt test blocks used in the function test and for the determination of compatibility with asphalt pavements
|
| EN 13880-12-2003
| 热接合密封剂 第12部分：粘结试验（配制法）中使用的混凝土试验块制品的试验方法
| Hot applied joint sealants - Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods)
|
| EN 13880-13-2003
| 热接合密封剂 第13部分：断续拉伸（附着力试验）测定的试验方法
| Hot applied joint sealants - Part 13: Test method for the determination of the discontinuous extension (adherence test)
|
| EN 13880-2-2003
| 热接合密封剂 第2部分：25℃下锥穿透力测定的试验方法
| Hot applied joint sealants - Part 2: Test method for the determination of cone penetration at 25℃
|
| EN 13880-3-2003
| 热接合密封剂 第3部分：穿透力和恢复性（弹性）测定的试验方法
| Hot applied joint sealants - Part 3: Test method for the determination of penetration and recovery (resilience)
|
| EN 13880-4-2003
| 热接合密封剂 第4部分：热阻测定的试验方法 穿透力值的变化
| Hot applied joint sealants - Part 4: Test method for the determination of heat resistance; Change in penetration value
|
| EN 13880-7-2003
| 热接合密封剂 第7部分：接合密封剂的功能试验
| Hot applied joint sealants - Part 7: Function testing of joint sealants
|
| EN 13880-8-2003
| 热接合密封剂 第8部分：燃料浸没后阻燃接合密封剂重量变化测定的试验方法
| Hot applied joint sealants - Part 8: Test method for the determination of the change in weight of fuel resistance joint sealants after fuel immersion
|
| EN 13880-9-2003
| 热接合密封剂 第9部分：与沥青路面相容性测定的试验方法
| Hot applied joint sealants - Part 9: Test method for the determination of compatibility with asphalt pavements
|
| EN 14187-1-2003
| 低温用接缝密封剂 第1部分：凝固速率测定的试验方法
| Cold applied joint sealants - Part 1: Test method for the determination of the rate of cure
|
| EN 14187-2-2003
| 低温用接缝密封剂 第2部分：消耗时间测定的试验方法
| Cold applied joint sealants - Part 2: Test method for the determination of tack free time
|
| EN 14187-3-2003
| 低温用接缝密封剂 第3部分： 自均涂性测定的试验方法
| Cold applied joint sealants - Part 3: Test method for the determination of self-levelling properties
|
| EN 14187-4-2003
| 低温用接缝密封剂 第4部分：在试验燃料中浸渍后质量和体积变化测定的试验方法
| Cold applied joint sealants - Part 4: Test method for the determination of the change in mass and volume after immersion in test fuel
|
| EN 14187-5-2003
| 低温用接缝密封剂 第5部分：抗水解性测定的试验方法
| Cold applied joint sealants - Part 5: Test method for the determination of the resistance to hydrolysis
|
| EN 14187-6-2003
| 低温用接缝密封剂 第6部分：在化学溶液中浸渍后粘着力/粘合力特性测定的试验方法
| Cold applied joint sealants - Part 6: Test method for the determination of the adhesion/cohesion properties after immersion in chemical liquids
|
| EN 14187-7-2003
| 低温用接缝密封剂 第7部分：耐火性测定的试验方法
| Cold applied joint sealants - Part 7: Test method for the determination of resistance to flame
|
| EN 14187-8-2003
| 低温用接缝密封剂 第8部分：用紫外线照射法进行人工风化测定的试验方法
| Cold applied joint sealants - Part 8: Test method for the determination of the artificial weathering by UV-irradiation
|
| EN 1448-1996
| 塑料管道系统 玻璃增强热固塑料(GRP)组件 带弹性密封件的刚性锁紧插承接合的设计查验试验方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of rigid locked socket-and-spigot joints with elastomeric seals
|
| EN 1680-1997
| 塑料管道系统 聚乙烯(PE)管道系统用阀门 传动装置的弯曲时和弯曲后密封性的试验方法
| Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanism
|
| EN 1989-2000
| 热塑性管道系统 埋地无压污水用接头 通过估计密封压力对热塑弹性塑料(TPE)密封接头的长时间密封性能的试
| Thermoplastics piping systems - Joints for buried non-pressure sewerage applications - Test method for long-term sealing performance of joints with thermoplastic elastomer (TPE) seals by estimating the sealing pressure
|
| EN 2591-324-1998
| 航空航天系列 光电连接元件 试验方法 第324部分：界面密封
| Aerospace series - Elements of electrical and optical connection - Test methods - Part 324: Interfacial sealing
|
| EN 2591-407-1999
| 航空航天系列 光电连接元件 试验方法 第407部分：接触固定系统和密封件的耐久性
| Aerospace series - Elements of electrical and optical connection - Test methods - Part 407: Durability of contact retention system and seals
|
| EN 2591-512-2002
| 航空航天系列 光电连接元件 试验方法 第512部分：密封连接器外壳不可拆卸的牢固性
| Aerospace series - Elements of electrical and optical connection; Test methods - Part 512: Effectiveness of non-removeable fixing of hermetically sealed connector shell
|
| EN 2591-6324-2001
| 航空航天系列 光电连接元件 试验方法 第6324部分：光学元件 界面密封／注：与EN2591－100结合使用
| Aerospace series - Elements of electrical and optical connection; Test methods - Part 6324: Optical elements; Interfacial sealing / Note: Applies in conjunction with EN 2591-100
|
| EN 26927-1990
| 房屋建造 勾缝用品 密封剂 词汇
| Building construction-Jointing products; Sealants; Vocabulary (ISO 6927:1981)
|
| EN 28339-1990
| 房层建筑 连接件 密封件 拉伸性能的测定
| Building construction - Jointing products - Sealants - Determination of tensile properties (ISO 8339:1984)
|
| EN 28340-1990
| 房层建筑 连接件 密封件 延伸状态的拉伸性能测定
| Building construction Jointing products - Sealants; Determination of tensile properties at maintained extension (ISO 8340:1984)
|
| EN 28394-1990
| 房层建筑 连接件 单个密封件可挤压性的测定
| Building construction - Jointing products - Determination of extrudability of one-component sealants (ISO 8394:1988)
|
| EN 29046-1990
| 房层建筑 密封胶 恒温下粘合性能的测定
| Building construction - Jointing products - Determination of adhesion/cohesion properties at constant temperatures (ISO 9046:1987)
|
| EN 29048-1990
| 房屋建筑 连接件 标准元件上密封稳定性的测定
| Building construction; jointing products; determination of extrudability of sealants using standardized apparatus (ISO 9048:1987)
|
| EN 29885-1994
| 广口玻璃容器.顶部密封表面的平面度偏差.试验方法
| Wide-mouth glass containers; deviation from flatness of top sealing surface; test methods (ISO 9885:1991)
|
| EN 2997-5-1997
| 航空航天系列 连续运行温度为175℃、200℃、最高温度为260℃时、耐火或不耐火的用有螺纹环连接的电连接器
| Aerospace series - Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures 175℃ continuous, 200℃ continuous, 260℃ peak - Part 5: Hermetic square flange receptacle - Product standard
|
| EN 2997-6-1997
| 航空航天系列 连续运行温度为175℃、200℃、最高温度为260℃时、耐火或不耐火的用有螺纹环连接的电连接器
| Aerospace series - Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures 175℃ continuous, 200℃ continuous, 260℃ peak - Part 6: Hermetic jam-nut mounted receptacle - Product standard
|
| EN 2997-7-1997
| 航空航天系列 连续运行温度为175℃、200℃、最高温度为260℃时、耐火或不耐火的用有螺纹环连接的电连接器
| Aerospace series - Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures 175℃ continuous, 200℃ continuous, 260℃ peak - Part 7: Hermetic receptacle with round flange attached by sold
|
| EN 3-2-1996
| 便携式灭火器 第2部分：密封性、介电试验、填塞试验、特别规定
| Portable fire extinguishers - Part 2: Tightness, dielectric test, tamping test, special provisions
|
| EN 3081-2001
| 航空航天系列 钛合金管连接件8°30′修理用带动态梁密封端头的焊接箍圈
| Aerospace series - Pipe coupling 8°30′in titanium alloy - Ferrules, welded with dynamic beam seal end, for repair
|
| EN 3243-2001
| 航空航天系列 钛合金管连接件8°30′ 带动态梁密封端头的焊接箍
| Aerospace series - Pipe coupling 8?30 in titanium alloy - Ferrule, welded, with dynamic beam seal end
|
| EN 3269-2001
| 航空航天系列 钛合金管连接件8°30′ 带动态梁密封端头的盲箍
| Aerospace series - Pipe coupling 8?30 in titanium alloy - Ferrules, blind, with dynamic beam seal end
|
| EN 3272-2001
| 航空航天系列 钛合金管连接件8°30′带动态梁密封端头的焊接金属箍 几何结构
| Aerospace series - Pipe coupling 8?30 - Dynamic beam seal end for ferrule, welded; Geometric configuration
|
| EN 3273-2001
| 航空航天系列 钛合金管连接件8°30′ 带动态梁密封端的弯管、十字管和三通接头 几何结构
| Aerospace series - Pipe coupling 8?30 - Dynamic beam seal end for elbows, tees and crosses; Geometric configuration
|
| EN 3275-2002
| 航空航天系列 管连接件8°30′ 达到 28000 kPa 动态梁密封 米制系列 技术规范
| Aerospace series - Pipe coupling 8?0 up to 28000 kPa - Dynamic beam seal; Metric series; Technical specification
|
| EN 3561-2001+AC-2003
| 航空航天系列 钛合金管连接件8°30′具有动态梁密封端箍圈 焊接和轧制管端口
| Aerospace series - Pipe coupling 8?0 in titanium alloy - Ferrules with dynamic beam seal end, welded and reduced at pipe end
|
| EN 3867-2003
| 航空航天系列 管连接 松套法兰和密封垫 TI-P64001钛合金法兰
| Aerospace series - Pipe couplings, loose flanges and seals - Flanges in titanium alloy TI-P64001 / Note: To be replaced by prEN 3867 (2003-05).
|
| EN 3868-2003
| 航空航天系列 管连接 松套法兰和密封垫 TI-P64001钛合金焊接法兰连接器
| Aerospace series - Pipe couplings, loose flanges and seals - Flange connectors, welded, in titanium alloy TI-P64001 / Note: To be replaced by prEN 3868 (2003-05).
|
| EN 3869-2003
| 航空航天系列 管连接 松套法兰和密封垫 碳氟橡胶垫和铝合金附件
| Aerospace series - Pipe couplings, loose flanges and seals - Seals in fluorocarbon rubber and armature in aluminium alloy / Note: To be replaced by prEN 3869 (2003-05).
|
| EN 4054-2003
| 航空航天系列 管连接、松套法兰和密封件 碳氟橡胶密封件和铝合金附件 技术规范
| Aerospace series - Pipe couplings, loose flanges and seals - Seals in fluorocarbon rubber and armature in aluminium alloy; Technical specification / Note: To be replaced by prEN 4054 (2003-05).
|
| EN 415-3-1999
| 包装机械安全 第3部分：成型、填充和密封机械
| Safety of packaging machines - Part 3: Form, fill and seal machines
|
| EN 4550-1-2003
| 航空航天系列 37度联管节 英制系列设计结构 第1部分：球形阳密封端头
| Aerospace series - Pipe coupling 37? Design configuration; Inch series - Part 1: Male sealing ends, spherical
|
| EN 4550-4-2003
| 航空航天系列 37度联管节 设计结构 英制系列 第4部分：阴密封端头
| Aerospace series - Pipe coupling 37? Design configuration; Inch series - Part 4: Female sealing ends
|
| EN 464-1994
| 包括气溶液体和固体粒子的抗液态和气态化学品的防护服 试验方法：气密服的密封性测定(内压力试验)
| Protective clothing for use against liquid and gaseous chemicals, including aerosols and solid particles - Test method: Determination of leak-tightness of gas-tight suits (internal pressure test)
|
| EN 465-1995+A1-1998
| 防护服 液态化学品防护 服装不同部分间喷涂密封连接的化学品防护服的性能要求（4型设备）
| Protective clothing - Protection against liquid chemicals - Performance requirements for chemical protective clothing with spray-tight connections between different parts of the clothing (Type 4 equipment)
|
| EN 50015-1998
| 潜在爆炸环境用防爆电气 O级密封设备
| Electrical apparatus for potentially explosive atmospheres - Oil immersion “O”
|
| EN 50016-2002
| 潜在爆炸环境用防爆电气 p级密封设备
| Electrical apparatus for potentially explosive atmospheres - Pressurized apparatus "p"
|
| EN 50028-1987
| 潜在爆炸性环境用防爆电气设备m 型密封
| Electrical apparatus for potentially explosive atmospheres; encapsulation“m”
|
| EN 50216-3-2002+A1-2002
| 电源变压器及电抗器配件 第3部分：未充气的密封充液式变压器和电抗器用保护继电器
| Power transformes and reactor fittings - Part 3: Protective relay for hermetically sealed liquid-immersed transformers and reactors without gaseous cushion
|
| EN 50262-1998+A1-2001
| 电气设备用米制电缆密封装置
| Metric cable glands for electrical installations
|
| EN 524-6-1997
| 预应力钢筋束用钢带材护套 试验方法 第6部分：密封性的测定(水流失的测定)
| Steel strip sheaths for prestressing tendons - Test methods - Part 6: Determination of leaktightness (Determination of water loss)
|
| EN 549-1994
| 燃气器具和设备密封件和隔膜用橡胶材料
| Rubber materials for seals and diaphragms for gas appliances and gas equipmemt
|
| EN 60068-2-17-1994
| 环境试验 第2-17部分：试验Q： 密封
| Environmental testing - Part 2: Tests - Test Q: Sealing (IEC 60068-2-17:1994)
|
| EN 60191-6-8-2001
| 半导体器件的机械标准化 第6-8部分：表面安装半导体器件封装外形图绘制的一般规则 玻璃密封陶瓷四面扁平
| Mechanical standardization of semiconductor devices - Part 6-8: General rules for the preparation of outline drawings of surface mounted semiconductor device packages; Design guide for glass sealed ceramic quad flatpack (G-QFP) (IEC 60191-6-8:2001)
|
| EN 60512-12-6-1996
| 电子设备用机电元件 基本试验规程和测量方法 第12部分：可钎焊性试验方法第6节：试验12f：机械钎焊焊接过
| Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 12: Soldering tests - Section 6: Test 12f: Sealing against flux and cleaning solvents in machine soldering (IEC 60512-12-6:1996)
|
| EN 60512-14-7-1998
| 电子设备用机电元件 基本试验规程和测量方法 第14部分：密封试验 第7节：试验14g 水冲击
| Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 14: Sealing tests - Section 7: Test 14g: Impacting water (IEC 60512-14-7:1997)
|
| EN 60512-23-3-2001
| 电子设备用机电元件 基本试验规程和测量方法 第23-3部分:试验23C:插头和加速器的密封效果
| Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 23-3: Test 23c: Shielding effectiveness of connectors and accessories (IEC 60512-23-3:2000)
|
| EN 60622-2003
| 含有碱性或非酸性电解液的蓄电池和蓄电池组 密封隔镍棱柱形可充电单体电池
| Secondary cells and batteries containing alkaline or other non-acid electrolytes - Sealed nickel-cadmium prismatic rechargeable single cells (IEC 60622:2002) / Note: Endorsement notice
|
| EN 60730-2-4-1993+A1-1998
| 家用和类似用途的电气自动控制器 第２－４部分：密封和半密封型电动－压缩机组的电动机热保护器
| Automatic electrical controls for household and similar use; part 2: particular requirements for thermal motor protectors for motor-compressors of hermetic and semi-hermetic type (IEC 60730-2-4:1990, modified)
|
| EN 60749-8-2003
| 半导体器件 机械和气候试验方法 第8部分：密封
| Semiconductor devices - Mechanical and climatic test methods - Part 8: Sealing (IEC 60749-8:2002 + corrigendum 2003) / Note: Endorsement notice
|
| EN 61150-1993
| 碱性二性电池和电池组 密封镍镉扣式可充电整体电池组
| Alkaline secondary cells and batteries - Sealed nickel-cadmium rechargeable monobloc batteries in button cell design (IEC 61150:1992 + corrigendum 1992)
|
| EN 61300-2-25-1997
| 光纤互连器件和无源元件 基本试验和测量程序 第2-25部分：试验 外壳密封耐久性
| Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-25: Tests-Sealing endurance for closures (IEC 61300-2-25:1995)
|
| EN 61300-2-38-1997
| 光纤互连器件和无源元件 基本试验和测量程序 第2-38部分：试验 加压光纤器件外壳的密封性
| Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-38: Tests-Sealing for pressurized closures of fibre optic devices (IEC 61300-2-38:1995)
|
| EN 61951-1-2003
| 含碱性或其它非酸性电解质的二次电池和电池组 轻便密封可充单体电池 第1部分：镉镍电池
| Secondary cells and batteries containing alkaline or other non-acid electrolytes - Portable sealed rechargeable single cells - Part 1: Nickel-cadmium (IEC 61951-1:2003) / Note: Endorsement notice
|
| EN 61951-2-2003
| 碱性或其它非酸性蓄电池和蓄电池组 便携式密封可充单体电池 第2部分：金属氢化物镍电池
| Secondary cells and batteries containing alkaline or other non-acid electrolytes - Portable sealed rechargeable single cells - Part 2: Nickel-metal hydride (IEC 61951-2:2003) / Note: Endorsement notice
|
| EN 62133-2003
| 含碱性或其它非酸性电解液的二次电池和电池组 便携式密封二次电池和由它们组成的便携式电池组的安全要求
| Secondary cells and batteries containing alkaline or other non-acid electrolytes - Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications (IEC 62133:2002) / Note: Endorsement notice
|
| EN 624-2000
| 专用LPG（液化石油气）器具规范 车、船上安装的室内密封LPG空间加热设备
| Specification for dedicated LPG appliances - Room sealed LPG space heating equipment for installation in vehicles and boats
|
| EN 681-1-1996+A1-1998+A2-2002+AC-2002
| 弹性密封件 供水和排水管道用管联接密封件的材料要求 第1部分：琉化橡胶
| Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber
|
| EN 681-2-2000+A1-2002
| 弹性密封件 供水和排水管道用管联接密封件的材料要求 第2部分：热塑性合成橡胶
| Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
|
| EN 681-3-2000+A1-2002
| 弹性密封件 供水和排水管道用管联接密封件的材料要求 第3部分：硫化橡胶的泡沫材料
| Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber
|
| EN 681-4-2000+A1-2002
| 弹性密封件 供水和排水管道用管联接密封件的材料要求 第4部分：浇铸聚氨酯密封元件
| Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements
|
| EN 682-2002
| 弹性密封件 用于运送气体和碳氢化合物液体的管道和配件的密封件的材料要求
| Elastomeric seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids
|
| EN 713-1993
| 塑料管道系统 配件和聚烯烃压力管间的机械接合件 弯曲时组件内部压力密封性的试验方法
| Plastic piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending
|
| EN 714-1994
| 热塑管道系统 压力管和模塑配件间的无端部负载的弹性密封环型接合件 在无轴向推力时内部流体静力学压力下
| Thermoplastics piping systems - Non-end-load-bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings - Test method for leaktightness under internal hydrostatic pressure without end thrust
|
| EN 715-1994
| 热塑管道系统 小直径压力管和配件间端部负荷的接合件 在包含轴向推力的内部水压下密封性的试验方法
| Thermoplastics piping systems - End-load bearing joints between small diameter pressure pipes and fittings-Test method for leaktightness under internal water pressure, including end thrust
|
| EN 751-1-1996
| 接触第1、2、3家庭用燃气和热水的金属螺纹接头的密封材料 第1部分：气密连接
| Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds
|
| EN 751-2-1996
| 接触第1、2、3家庭用燃气和热水的金属螺纹接头的密封材料 第2部分：非硬化连接
| Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds
|
| EN 751-3-1996+AC-1997
| 接触第1、2、3家庭用燃气和热水的金属螺纹接头的密封材料 第3部分：非烧结过的聚四氟乙烯密封带
| Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 3: Unsintered PTFE tapes
|
| EN 803-1994
| 塑料管道系统 压力管道的弹性密封环状连接的喷射铸造热塑性部件 无轴向推力的瞬时内压阻力试验方法
| Plastics piping systems - Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust
|
| EN 868-10-2000
| 经消毒的医疗器械用包装材料和系统 第10部分：生产热密封袋、卷轴和盖的聚烯烃粘性涂层非编织材料 要求和
| Packaging materials and systems for medical devices which are to be sterilized - Part 10: Adhesive coated nonwoven materials of polyolefines for use in the manufacture of heat sealable pouches, reels and lids - Requirements and test methods
|
| EN 868-5-1999+AC-2001
| 经消毒的医疗器械用包装材料和系统 第5部分：纸、塑料薄膜结构的热和可自密封袋及卷轴 要求和试验方法
| Packaging materials and systems for medical devices which are to be sterilized - Part 5: Heat and self-sealable pouches and reels of paper and plastic film construction - Requirements and test methods
|
| EN 868-7-1999
| 经消毒的医疗器械用包装材料和系统 第7部分：生产经氧化乙烯或辐射消毒的医用热密封包所用的粘性涂覆纸
| Packaging materials and systems for medical devices which are to be sterilized - Part 7: Adhesive coated paper for the manufacture of heat sealable packs for medical use for sterilization by ethylene oxide or irradiation - Requirements and test methods
|
| EN 868-9-2000
| 经消毒的医疗器械用包装材料和系统 第9部分：生产热密封袋、卷轴和盖的聚烯烃非涂层非编织材料 要求和试
| Packaging materials and systems for medical devices which are to be sterilized - Part 9: Uncoated nonwoven materials of polyolefines for use in the manufacture of heat sealable pouches, reels and lids - Requirements and test methods
|
| EN 911-1995
| 塑料管道系统 热塑塑料压力管道用的弹性密封环型接头和机械接头 外部液压条件下防漏密封试验方法
| Plastics piping systems - Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - Test method for leaktightness under external hydrostatic pressure
|
| EN 917-1997
| 塑料管系统 热塑阀门 抗内压和泄漏密封性的试验方法
| Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal pressure and leaktightness
|
| EN ISO 10563-1997
| 房屋建筑 接合用密封胶 重量和体积变化的测定
| Building construction - Sealants for joints - Determination of change in mass and volume (ISO 10563:1991)
|
| EN ISO 10590-1997
| 房屋建筑 密封胶 浸水后保持延伸粘合性能的测定
| Building construction - Sealants - Determination of adhesion/cohesion properties at maintained extension after immersion in water (ISO 10590:1991)
|
| EN ISO 10591-1997
| 房屋建筑 密封胶 浸水后粘合性能的测定
| Building construction - Sealants - Determination of adhesion/cohesion properties after immersion in water (ISO 10591:1991)
|
| EN ISO 11431-2002
| 房屋建筑 密封胶 受热、接触水和透过玻璃暴露于人造光后密封胶的粘合性的测定
| Building construction - Jointing products - Determination of adhesion/cohesion properties of sealants after exposure to heat, water and artificial light through glass (ISO 11431:2002)
|
| EN ISO 11432-1997
| 房屋建筑 密封胶 耐压性的测定
| Building construction - Sealants - Determination of resistance to compression (ISO 11432:1993)
|
| EN ISO 12216-2002
| 小艇 窗、船窗、舱口、固定舷窗和门 强度和水密封度要求
| Small craft - Windows, portlights, hatches, dead-lights and doors - Strength and watertightness requirements (ISO 12216:2002)
|
| EN ISO 13783-1997
| 塑料管道系统 硬聚氯乙烯(PVC-U)端部承受负荷的双承口连接件 密封和承受弯曲及内压的试验方法
| Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double socket joints - Test method for leaktightness and strength while subjected to bending and internal pressure (ISO 13783:1997)
|
| EN ISO 13844-2000
| 塑料管道系统 用于硬(聚氯乙烯)(PVC-U) 管道的弹性密封环式承口连接件 负压下密封试验方法
| Plastics piping systems - Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure (ISO 13844:2000)
|
| EN ISO 13845-2000
| 塑料管道系统 用于硬(聚氯乙烯)(PVC-U) 管道的弹性密封环式承口连接件 内压下角度偏转密封试验方法
| Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with angular deflection (ISO 13845:2000)
|
| EN ISO 13846-2000
| 塑料管道系统 热塑性加压塑料管道用端部负载轴承和非端部负载轴承的安装和连接 在内水压下长期密封的试验
| Plastics piping systems - End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaktightness under internal water pressure (ISO 13846:2000)
|
| EN ISO 15783-2003
| 未密封的旋转动态泵 II级 规范
| Seal-less rotodynamic pumps - Class II - Specification (ISO 15783:2002)
|
| EN ISO 228-1-2003
| 非螺纹密封的管螺纹 第1部分：标记、尺寸和公差
| Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
|
| EN ISO 228-2-2003
| 非螺纹密封的管螺纹 第2部分：用极限量规检验
| Pipe threads where pressure-tight joints are not made on the threads - Part 2: Verification by means of limit gauges (ISO 228-2:1987)
|
| EN ISO 483-1999
| 塑料 水溶液在小密封器中恒定相对湿度值法
| Plastics - Small enclosures for conditioning and testing using aqueous solutions to maintain relative humidity at constant value (ISO 483:1988)
|
| EN ISO 9047-2003
| 房屋建筑 密封胶 变温下的粘合性能的测定
| Building construction - Jointing products - Determination of adhesion/cohesion properties of sealants at variable temperatures (ISO 9047:2001)
|
| EN ISO 9222-1-1995
| 技术制图 动密封应用 第1部分：通用简化画法
| Technical drawings - Seals for dynamic application - Part 1: General simplified representation (ISO 9222-1:1989)
|
| EN ISO 9222-2-1994
| 技术制图 动密封应用 第2部分：简化画法
| Technical drawings - Seals of dynamic application - Part 2: Detailed simplified representation (ISO 9222-2:1989)
|
| EN ISO 9974-1-2000
| 通用和液压传动用联接件 带ISO 261 弹性螺纹或金属 金属密封的气门和双头螺栓端头 第1部分：螺纹气门
| Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 1: Threaded ports (ISO 9974-1:1996)
|
| EN ISO 9974-2-2000
| 通用和液压传动用联接件 带ISO 261 弹性螺纹或金属 金属密封的气门和双头螺栓端头 第2部分：弹性密封的
| Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 2: Stud ends with elastomeric sealing (type E) (ISO 9974-2:1996)
|
| EN ISO 9974-3-2000
| 通用和液压传动用联接件 带ISO 261 弹性螺纹或金属 金属密封的气门和双头螺栓端头 第3部分：金属 金属
| Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 3: Stud ends with metal-to-metal sealing (type B) (ISO 9974-3:1996)
|
| HD 138 S2-1990
| 加压的波导管和组件的密封试验
| Sealing test for pressurized waveguide tubing and assemblies
|
| prEN 1016-1993
| 塑料管道系统 非可塑聚氯乙烯一端受载的双孔接头 弯曲和内部压力时的密封性和强度试验方法
| Plastics piping systems; unplasticized poly(vinyl chloride) (PVC-U) end-load bearing double socket joints; test method for leaktightness and strength while subjected to bending and internal pressure
|
| prEN 10226-1-1995
| 螺纹式密封的管螺纹 第1部分：名称、尺寸和公差
| Pipe threads where pressure tight joints are made on the threads - Part 1: Designation, dimensions and tolerances
|
| prEN 10226-2-2002
| 螺纹式密封的管螺纹 第2部分：锥形内螺纹和锥形外螺纹 名称、公差和尺寸
| Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads; Dimensions, tolerances and designation
|
| prEN 13022-1-2002
| 建筑物玻璃 建筑密封玻璃窗 第1部分：作用、要求和术语
| Glass in building - Structural sealant glazing - Part 1: Glass products for structural sealant glazing systems; Supported and unsupported monolithic and multiple glazing
|
| prEN 13022-2-2003
| 建筑物玻璃 建筑密封玻璃窗 第2部分：玻璃
| Glass in building - Structural sealant glazing - Part 2: Product standard for ultra-violet resistant sealant and structural sealant
|
| prEN 13022-3-2003
| 建筑物玻璃 建筑密封玻璃窗 第3部分：密封 试验方法
| Glass in building - Structural sealant glazing - Part 3: Assembly rules
|
| prEN 13022-4-1997
| 建筑物玻璃 建筑密封玻璃窗 第4部分：装配规则
| Glass in building - Structural sealant glazing - Part 4: Assembly rules
|
| prEN 1336-1993
| 塑料管道系统 热塑性压力管道用终端承载和无承开组件和接头 内部水压力下长期密封性试验方法
| Plastics piping systems; end-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping; test method for long-term leaktightness under internal water pressure
|
| prEN 13555-2002
| 法兰及其联接 与密封圆法兰联接设计原则相关的密封参数和试验程序
| Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections
|
| prEN 1366-4-2003
| 服务设施的耐火试验 第4部分：直线连接的密封
| Fire resistance tests for service installations - Part 4: Linear joint seals
|
| prEN 13763-10-2000
| 民用炸药 雷管和继电器 第10部分：密封塞抗扭转性的测定方法
| Explosives for civil uses - Detonators and relays - Part 10: Methods for the determination of resistance to torsion of sealing plugs
|
| prEN 13880-5-2002
| 热接合密封剂 试验方法 第5部分：流动阻力的测定
| Hot applied joint sealants - Part 5: Test method for the determination of flow resistance
|
| prEN 13880-6-2003
| 热接合密封剂 试验方法 第6部分：试样制备
| Hot applied joint sealants - Part 6: Test method for the preparation of samples for testing
|
| prEN 14188-1-2001
| 接缝填料和密封剂 第1部分：热应用密封剂的规范
| Joint fillers and sealants - Part 1: Specifications for hot applied sealants
|
| prEN 14241-1-2001
| 烟囱 弹性密封剂和弹性密封 试验方法和材料要求 烟囱衬垫的密封
| Chimneys - Elastomeric seals and elastomeric sealants - Material requirements and test methods - Part 1: Seals in flue liners
|
| prEN 2349-412-2000
| 航空航天系列 继电器和接触器要求和试验程序 第412部分：密封
| Aerospace series - Requirements and test procedures for relays and contactors - Part 412: Seal
|
| prEN 2878-1998
| 航空航天系列 用MoS2润滑镀镉合金钢制扩口双耳状浮线密封耐空气（腐蚀）自锁系紧螺母 等级：900 MPa (环
| Aerospace series - Nuts, anchor, self-locking, air resistant, sealing, floating, two lug, with counterbore, in alloy steel, cadmium plated, MoS<(Index)2> lubricated - Classification: 900 MPa (at ambient temperature)/235℃
|
| prEN 2879-1998
| 航空航天系列 用MoS2润滑钝化抗腐蚀钢制扩口双耳状浮线密封耐空气（腐蚀）自锁系紧螺母 等级：900 MPa (
| Aerospace series - Nuts, anchor, self-locking, air resistant, sealing, floating, two lug, with counterbore, in corrosion resisting steel, passivated, MoS<(Index)2> lubricated - Classification: 900 MPa (at ambient temperature)/235℃
|
| prEN 2880-1998
| 航空航天系列 用MoS2润滑镀镉合金钢制扩口双耳状浮线密封耐燃油自锁系紧螺母 等级：900 MPa (环境温度)/1
| Aerospace series - Nuts, anchor, self-locking, fuel resistant, sealing, floating, two lug, with counterbore, in alloy steel, cadmium plated, MoS<(Index)2> lubricated - Classification: 900 MPa (at ambient temperature)/120℃
|
| prEN 2881-1998
| 航空航天系列 用MoS2润滑钝化耐腐蚀钢制扩口双耳状浮线密封耐燃油自锁系紧螺母 等级：900 MPa (环境温度)
| Aerospace series - Nuts, anchor, self-locking, fuel resistant, sealing, floating, two lug, with counterbore, in corrosion resisting steel, passivated, MoS<(Index)2> lubricated - Classification: 900 MPa (at ambient temperature)/120℃
|
| prEN 3095-1998
| 航空航天系列 密封剂 测试方法 延长装配时间的确定
| Aerospace series - Sealants - Test method - Determination of extended assembly time
|
| prEN 3102-2000
| 航空航天系列 密封剂 测试方法 低温挠性的确定
| Aerospace series - Sealants test methods - Determination of low-temperature flexibility
|
| prEN 3545-002-2002
| 航空航天系列 尾部密封和无密封 塑料护套、锁紧装置、操作温度5℃到175℃的矩形电接点 第002部分：性能
| Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55℃ to 175℃ - Part 002: Specification of performance and contact arrangements
|
| prEN 3646-005-2001
| 航空航天系列 连续操作温度175 ℃或 200℃、圆形卡口式联结电连接器 第005部分：密封的方法兰固插座 产
| Aerospace series - Connectors, electrical, circular, bayonet coupling, operating temperature 175℃ or 200℃ continuous - Part 005: Receptacle, hermetic, square flange mounting; Product standard
|
| prEN 3646-006-2001
| 航空航天系列 连续操作温度175 ℃或 200℃、圆形卡口式联结电连接器 第006部分：密封锁紧螺母固插座
| Aerospace series - Connectors, electrical, circular, bayonet coupling, operating temperature 175℃ or 200℃ continuous - Part 006: Receptacle, hermetic, jam-nut mounting; Product standard
|
| prEN 3646-007-2001
| 航空航天系列 连续操作温度175 ℃或 200℃、圆形卡口式联结电连接器 第007部分：、密封的焊接或铜焊圆法
| Aerospace series - Connectors, electrical, circular, bayonet coupling, operating temperature 175℃ or 200℃ continuous - Part 007: Receptacle, hermetic, round flange, welding or brazing mounting; Product standard
|
| prEN 4067-005-2000
| 航空航天系列 防火的最高操作温度为260℃的螺纹式环耦合的防凹口圆电连接器 第005部分：密封的方形法兰式
| Aerospace series - Connectors, electrical, circular, scoop-proof, coupled by threaded ring, fire-resistant, operating temperature 260℃ peak - Part 005: Hermetic square flange receptacle - Product standard
|
| prEN 4067-006-2000
| 航空航天系列 防火的最高操作温度为260℃的螺纹式环耦合的防凹口圆电连接器 第006部分：密封的装锁紧螺母
| Aerospace series - Connectors, electrical, circular, scoop-proof, coupled by threaded ring, fire-resistant, operating temperature 260℃ peak - Part 006: Hermetic jam-nut mounted receptacle - Product standard
|
| prEN 4067-007-2000
| 航空航天系列 防火的最高操作温度为260℃的螺纹式环耦合的防凹口圆电连接器 第007部分：有钎焊或铜焊圆法
| Aerospace series - Connectors, electrical, circular, scoop-proof, coupled by threaded ring, fire-resistant, operating temperature 260℃ peak - Part 007: Hermetic receptacle with round flange attached by soldering or brazing - Product standard
|
| prEN 4529-001-2001
| 航空航天系列 电和光学连接原件 密封插头 第001部分：技术规范
| Aerospace series - Elements of electrical and optical connection - Sealing plugs - Part 001: Technical specification
|
| prEN 4529-002-2001
| 航空航天系列 电和光学连接件 密封插头 第002部分：产品标准的索引
| Aerospace series - Elements of electrical and optical connection - Sealing plugs - Part 002: Index of product standards
|
| prEN 4529-003-2001
| 航空航天系列 电和光学连接件 密封插头 第003部分：T级 产品标准
| Aerospace series - Elements of electrical and optical connection - Sealing plugs - Part 003: Class T; Product standard
|
| prEN 495-2-1991
| 热塑性覆盖和密封板 抗撕裂性测定 梯形试样法
| Thermoplastic roofing and sealing sheets; determination of tear resistance; trapezoidal test specimen method
|
| prEN 495-3-1991
| 热塑性和弹性覆盖和密封板 抗开裂压力的测定
| Thermoplastic and elastomeric roofing and sealing sheets; determination of split pressure resistance
|
| prEN 495-4-1991
| 热塑性和弹性覆盖和密封板 水蒸汽传递性质的测定
| Thermoplastic and elastomeric roofing and sealing sheets; determination of water vapour transmission properties
|
| prEN 762-1995
| 塑料管道和导管系统 热塑系统用弹性密封接头 密封环保持力和损坏的试验方法
| Plastics piping and ducting systems - Joints with elastomeric seals for thermoplastic systems - Test method for retention of, and damage to, sealing rings
|
| prEN ISO 19019-2002
| 远洋船和造船技术 规划、实施及报告密封试验
| Sea-going vessels and marine technology - Guide for planning, carrying out and reporting seal trials (ISO/DIS 19019:2002)
|
| prEN ISO 7-2-2001
| 用螺纹密封的管螺纹 第2部分：用极限量规检验
| Pipe threads where pressure-tight joints are made on the threads - Part 2: Verification by means of limit gauges (ISO 7-2:2000)
|
| prEN ISO 8339-2001
| 房屋建筑 密封件 拉伸性能测定
| Building construction - Sealants - Determination of tensile properties (Extension to break) (ISO/DIS 8339:2001)
|
| prEN ISO 8340-2001
| 房屋建筑 密封件 延伸状态的拉伸性能测定
| Building construction - Sealants - Determination of tensile properties at maintained extension (ISO/DIS 8340:2001)
|
| 编号 | 中文名称 | 英文名称 |
|---|