| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| IEC 60746-4-1992 | 电化学分析仪性能表示法 第4部分:用包有薄膜的电流传感器测量水中的溶解氧 | Expression of performance of electrochemical analyzers; part 4: dissolved oxygen in water measured by membrane covered amperometric sensors |
| IEC 60947-5-6-1999 | 低压开关设备和控制设备 第5-6部分:控制电路器件和切换元件 接近传感器和切换放大器用直流连接器件(NAMUR) | Low-voltage switchgear and controlgear - Part 5-6: Control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR) |
| IEC 61146-1-1994 | 摄像机(PAL/SECAN/NTSC) 测量方法 第1部分:非广播单传感器摄像机 | Video cameras (PAL/SECAM/NTSC) - Methods of measurement - Part 1: Non-broadcast single-sensor cameras |
| IEC 61146-2-1997 | 摄像机(PAL/SECAN/NTSC) 测量方法 第2部分:两个和三个传感器的专业摄像机 | Video cameras (PAL/SECAM/NTSC) - Methods of measurement - Part 2: Two- and three-sensor professional cameras |
| IEC 61207-2 Corrigendum 1-1994 | 气体分析器性能表示.第2部分:气体中的氧(利用高温电化学传感器) | Expression of performance of gas analyzers - Part 2: Oxygen in gas (utilizing high-temperature electrochemical sensors) |
| IEC 61207-2-1994 | 气体分析器性能表示 第2部分:气体中的氧(利用高温电化学传感器) | Expression of performance of gas analyzers - Part 2: Oxygen in gas (utilizing high-temperature electrochemical sensors) |
| IEC 61326-2-3-2006 | 测量、控制和实验室用电气设备.电磁兼容性要求.第2-3部分:详细要求.有综合或遥感信号作用的传感器的试验结 | Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-3: Particular requirements - Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal conditioning |
| IEC 61329-1995 | 声系统设备 测量和规范发声器性能的方法(发声用电解传感器) | Sound system equipment - Methods of measuring and specifying the performance of sounders (electroacoustic transducers for tone production) |
| IEC 61757-1-1998 | 纤维光学传感器 第1部分:总规范 | Fibre optic sensors - Part 1: Generic specification |
| IEC 61828-2006 | 超声波.聚焦传感器.发送场的定义和测量方法 | Ultrasonics - Focusing transducers - Definitions and measurement methods for the transmitted fields |
| IEC/TR 61088-1991 | 超声波压电陶瓷传感器的特性和测量方法 | Characteristics and measurements of ultrasonic piezoceramic transducers |
| ISO 11786-1995 | 农业拖拉机和机械 固定在拖拉机上的传感器联接装置 技术规范 | Agricultural tractors and machinery - Tractor-mounted sensor interface - Specifications |
| ISO 12713-1998 | 无损检测 声发射检查 传感器的初次校正 | Non-destructive testing - Acoustic emission inspection - Primary calibration of transducers |
| ISO 12714-1999 | 无损检测 声发射检查 声发射传感器的二级校准 | Non-destructive testing - Acoustic emission inspection - Secondary calibration of acoustic emission sensors |
| ISO 12715-1999 | 超声无损检测 接触式传感器光束轮廓特性的检测程序和基准块 | Ultrasonic non-destructive testing - Reference blocks and test procedures for the characterization of contact search unit beam profiles |
| ISO 15106-1-2003 | 塑料.薄膜和薄片.水蒸气传输率的测定.第1部分:湿度探测传感器法 | Plastics; Film and sheeting - Determination of water vapour transmission rate - Part 1: Humidity detection sensor method |
| ISO 15106-2-2003 | 塑料.薄膜和薄片.水蒸气传输率的测定.第2部分:红外探测传感器法 | Plastics; Film and sheeting - Determination of water vapour transmission rate - Part 2: Infrared detection sensor method |
| ISO 15106-3-2003 | 塑料.薄膜和薄片.水蒸气传输率的测定.第3部分:电解探测传感器法 | Plastics; Film and sheeting - Determination of water vapour transmission rate - Part 3: Electrolytic detection sensor method |
| ISO 15367-2-2005 | 激光及激光相关设备.激光束波前形状测定用试验方法.第2部分:Shack-Hartmann传感器 | Lasers and laser-related equipment - Test methods for determination of the shape of a laser beam wavefront - Part 2: Shack-Hartmann sensors |
| ISO 15839-2003 | 水质.水用在线传感器/分析设备.规范及性能试验 | Water quality - On-line sensors/analysing equipment for water - Specifications and performance tests |
| ISO 16063-1-1998 | 振动与冲击传感器的校准方法 第1部分:基本概念 | Methods for the calibration of vibration and shock transducers - Part 1: Basic concepts |
| ISO 16063-11-1999 | 振动与冲击传感器的校准方法 第11部分:激光干涉法作主要的振动校准 | Methods for the calibration of vibration and shock transducers - Part 11: Primary vibration calibration by laser interferometry |
| ISO 16063-12-2002 | 振动和冲击传感器的校正方法.第12部分:用互易法作初级线圈振动校正 | Methods for the calibration of vibration and shock transducers - Part 12: Primary vibration calibration by the reciprocity method |
| ISO 16063-13-2001 | 振动和冲击传感器的校准方法 第13部分：用激光干涉法的基本校准 | Methods for the calibration of vibration and shock transducers - Part 13: Primary shock calibration using laser interferometry |
| ISO 16063-15-2006 | 振动和冲击传感器的校准方法.第15部分:用激光干涉法的初级角振动校准 | Methods for the calibration of vibration and shock transducers - Part 15: Primary angular vibration calibration by laser interferometry |
| ISO 16063-21-2003 | 振动和冲击传感器的校准方法.第21部分:与基准传感器进行比对的振动校准 | Methods for the calibration of vibration and shock transducers - Part 21: Vibration calibration by comparison with a reference transducer |
| ISO 16063-22-2005 | 振动和冲击传感器的校准方法.第22部分:与基准传感器进行比对的冲击校准 | Methods for the calibration of vibration and shock transducers - Part 22: Shock calibration by comparison to a reference transducer |
| ISO 16844-3 Technical Corrigendum 1-2006 | 道路车辆.速度记录器系统.第3部分:动作传感器接口 | Road vehicles - Tachograph systems - Part 3: Motion sensor interface |
| ISO 16844-3-2004 | 道路车辆.速度记录器系统.第3部分:动作传感器接口 | Road vehicles - Tachograph systems - Part 3: Motion sensor interface |
| ISO 22896-2006 | 道路车辆.使用者安全系统开发和传感器总线 | Road vehicles - Deployment and sensor bus for occupant safety systems |
| ISO 23570-1-2005 | 工业自动化系统和集成.工业设施的分布式安装.第1部分:传感器和传动器 | Industrial automation systems and integration - Distributed installation in industrial applications - Part 1: Sensors and actuators |
| ISO 5347-10-1993 | 振动与冲击传感器的校准方法 第10部分:大冲击法一次核准 | Methods for the calibration of vibration and shock pick-ups; part 10: primary calibration by high impact shocks |
| ISO 5347-11-1993 | 振动与冲击传感器的校准方法 第11部分:横向振动灵敏度测试 | Methods for the calibration of vibration and shock pick-ups; part 11: testing of transverse vibration sensitivity |
| ISO 5347-12-1993 | 振动与冲击传感器的校准方法 第12部分:横向冲击灵敏性的测试 | Methods for the calibration of vibration and shock pick-ups; part 12: testing of transverse shock sensitivity |
| ISO 5347-13-1993 | 振动与冲击传感器的校准方法 第13部分:基座应变灵敏度测试 | Methods for the calibration of vibration and shock pick-ups; part 13: testing of base strain sensitivity |
| ISO 5347-14-1993 | 振动与冲击传感器的校准方法 第14部分:安装在钢块上的无阻尼加速度计共振频率的测试 | Methods for the calibration of vibration and shock pick-ups; part 14: resonance frequency testing of undamped accelerometers on a steel block |
| ISO 5347-15-1993 | 振动与冲击传感器的校准方法 第15部分:声灵敏度测试 | Methods for the calibration of vibration and shock pick-ups; part 15: testing of acoustic sensitivity |
| ISO 5347-16-1993 | 振动与冲击传感器的校准方法 第16部分:安装力矩灵敏度测试 | Methods for the calibration of vibration and shock pick-ups; part 16: testing of mounting torque sensitivity |
| ISO 5347-17-1993 | 振动与冲击传感器的校准方法 第17部分:温度灵敏度比较测试法 | Methods for the calibration of vibration and shock pick-ups; part 17: testing of fixed temperature sensitivity |
| ISO 5347-18-1993 | 振动与冲击传感器的校准方法 第18部分:瞬变温度灵敏度测试法 | Methods for the calibration of vibration and shock pick-ups; part 18: testing of transient temperature sensitivity |
| ISO 5347-19-1993 | 振动与冲击传感器的校准方法 第19部分:磁灵敏度测试 | Methods for the calibration of vibration and shock pick-ups; part 19: testing of magnetic field sensitivity |
| ISO 5347-22-1997 | 振动与冲击传感器的校准方法 第22部分:加速计共振试验 普通方法 | Methods for the calibration of vibration and shock pick-ups - Part 22: Accelerometer resonance testing - General methods |
| ISO 5347-5-1993 | 振动与冲击传感器的校准方法 第5部分:地球引力校准 | Methods for the calibration of vibration and shock pick-ups; part 5: calibration by earth's gravitation |
| ISO 5347-7-1993 | 振动与冲击传感器的校准方法 第7部分:离心机法一次校准 | Methods for the calibration of vibration and shock pick-ups; part 7: primary calibration by centrifuge |
| ISO 5347-8-1993 | 振动与冲击传感器的校准方法 第8部分:双离心机法一次校准 | Methods for the calibration of vibration and shock pick-ups; part 8: primary calibration by dual centrifuge |
| ISO 7240-8-2007 | 火灾探测和报警系统.第8部分:使用带热传感器的电化电池的一氧化碳火灾探测器 | Fire detection and alarm systems - Part 8: Carbon monoxide fire detectors using an electro-chemical cell in combination with a heat sensor |
| ISO 7626-1-1986 | 振动与冲击 机械导纳的试验确定 第1部分:基本定义和传感器 | Vibration and shock; Experimental determination of mechanical mobility; Part 1 : Basic definitions and transducers |
| ISO 8042-1988 | 冲击与振动测量 惯性传感器的特性规定 | Shock and vibration measurements; characteristics to be specified for seismic pick-ups |
| ISO/TR 10305-2-2003 | 道路车辆.电磁场强度测量设备的校正.第2部分:9kHz-40GHz的电磁场传感器和探针(不包括天线)的校正用IEEE标准 | Road vehicles - Calibration of electromagnetic field strength measuring devices - Part 2: IEEE standard for calibration of electromagnetic field sensors and probes, excluding antennas, from 9 kHz to 40 GHz |
| 编号 | 中文名称 | 英文名称 |