| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| 2SP 68 to 2SP 71-1973 | 铝和铝合金100度精密埋头铆钉规范 | Specification for 100 countersunk precision head aluminium and aluminium alloy rivets |
| BS 1161-1977 | 结构用铝合金型材规范 | Specification for aluminium alloy sections for structural purposes |
| BS 1212-1-1990 | 浮子阀.第1部分:活塞式浮子阀(铜合金阀体)(不含浮子)规范 | Float operated valves - Specification for piston type float operated valves (copper alloy body) (excluding floats) |
| BS 1212-2-1990 | 浮子阀.第2部分:隔膜式浮子阀(铜合金阀体)(不含浮子)规范 | Float operated valves - Specification for diaphragm type float operated valves (copper alloy body) (excluding floats) |
| BS 1306-1975 | 铜与铜合金承压管道系统规范 | Specification for copper and copper alloy pressure piping systems |
| BS 143 & 1256-2000 | 可锻铸铁与铸铜合金螺纹管配件 | Threaded pipe fittings in malleable cast iron and cast copper alloy |
| BS 143 and 1256-2000 | 可锻铸铁和铸铜合金的螺纹管配件 | Threaded pipe fittings in malleable cast iron and cast copper alloy |
| BS 1473-1972 | 一般工程用可锻铝和铝合金规范.铆钉、螺栓和螺钉坯料 | Specification for wrought aluminium and aluminium alloys for general engineering purposes - rivet, bolt and screw stock |
| BS 1560-3.2-1989 | 管子、阀门和接头(规定等级)用圆法兰.第3部分:钢、铸铁和铜合金法兰.第2节:铸铁法兰规范 | Circular flanges for pipes, valves and fittings (Class designated) - Steel, cast iron and copper alloy flanges - Specification for cast iron flanges |
| BS 1640-1-1962 | 石油工业用钢对焊管管件规范.第1部分:锻制碳钢与铁素体合金钢管件 | Specification for steel butt-welding pipe fittings for the petroleum industry - Wrought carbon and ferritic alloy steel fittings |
| BS 1728-1-1951 | 铝与铝合金的分析方法.第1部分:铜的测定 | Methods for the analysis of aluminium and aluminium alloys - Determination of copper |
| BS 1728-10-1957 | 铝与铝合金的分析方法.第10部分:锰的测定(吸收测量法) | Methods for the analysis of aluminium and aluminium alloys - Determination of manganese (absorptiometric method) |
| BS 1728-11-1960 | 铝与铝合金的分析方法.第11部分:硅的测定(过氯酸法) | Methods for the analysis of aluminium and aluminium alloys - Determination of silicon (perchloric acid method) |
| BS 1728-12-1961 | 铝与铝合金的分析方法.第12部分:硅的测定(钼蓝吸收测定法) | Methods for the analysis of aluminium and aluminium alloys - Determination of silicon (absorptiometric molybdenum blue method) |
| BS 1728-14-1965 | 铝与铝合金的分析方法.第14部分:镍的测定(重量法) | Methods for the analysis of aluminium and aluminium alloys - Determination of nickel (gravimetric method) |
| BS 1728-15-1966 | 铝与铝合金的分析方法.第15部分:镍的测定(光度测量法) | Methods for the analysis of aluminium and aluminium alloys - Determination of nickel (photometric method) |
| BS 1728-16-1968 | 铝与铝合金的分析方法.第16部分:铬的测定(光度测量法) | Methods for the analysis of aluminium and aluminium alloys - Determination of chromium (photometric method) |
| BS 1728-17-1968 | 铝与铝合金的分析方法.第17部分:铬的测定(容量法) | Methods for the analysis of aluminium and aluminium alloys - Determination of chromium (volumetric method) |
| BS 1728-18-1970 | 铝与铝合金的分析方法.第18部分:锌的测定(EDTA离子交换容量法或极谱法) | Methods for the analysis of aluminium and aluminium alloys - Determination of zinc (ion-exchange-volumetric EDTA or polarographic method) |
| BS 1728-19-1971 | 铝与铝合金的分析方法.镁的测定(原子吸收法) | Methods for the analysis of aluminium and aluminium alloys - Determination of magnesium (atomic absorption method) |
| BS 1728-1971 | 铝与铝合金的分析方法.第19部分:镁的测定(原子吸收法) | Methods for the analysis of aluminium and aluminium alloys. Determination of magnesium (atomic absorption method) |
| BS 1728-20-1971 | 铝与铝合金的分析方法.第20部分:铅的测定(原子吸收法) | Methods for the analysis of aluminium and aluminium alloys - Determination of lead (atomic absorption method) |
| BS 1728-21-1973 | 铝与铝合金的分析方法.第21部分:锌(原子吸收法) | Methods for the analysis of aluminium and aluminium alloys - Zinc (atomic absorption method) |
| BS 1728-22-1972 | 铝与铝合金的分析方法.第22部分:镁的测定(CDTA容量法) | Methods for the analysis of aluminium and aluminium alloys - Determination of magnesium (volumetric CDTA method) |
| BS 1728-23-1976 | 铝与铝合金的分析方法.第23部分:铜(原子吸收法) | Methods for the analysis of aluminium and aluminium alloys - Copper (atomic absorption method) |
| BS 1728-24-1976 | 铝与铝合金的分析方法.第24部分:镍(原子吸收法) | Methods for the analysis of aluminium and aluminium alloys - Nickel (atomic absorption method) |
| BS 1728-25-1980 | 铝与铝合金的分析方法.第25部分:钛(变色酸分光光度法) | Methods for the analysis of aluminium and aluminium alloys - Titanium (spectrophotometric chromotropic acid method) |
| BS 1728-5-1953 | 铝与铝合金的分析方法.第5部分:铜的测定(吸收测量法) | Methods for the analysis of aluminium and aluminium alloys - Determination of copper (absorptiometric method) |
| BS 1728-6-1955 | 铝与铝合金的分析方法.第6部分:铁的测定(容量分析:氯化亚钛法) | Methods for the analysis of aluminium and aluminium alloys - Determination of iron (volumetric: titanous chloride method) |
| BS 1728-8-1957 | 铝与铝合金的分析方法.第8部分:铁的测定(1:10菲咯啉吸收测量法) | Methods for the analysis of aluminium and aluminium alloys - Determination of iron (absorptiometric 1:10-phenanthroline method) |
| BS 1728-9-1957 | 铝与铝合金的分析方法.第9部分:锰的测定(容量分析:亚砷酸盐/亚硝酸盐法) | Methods for the analysis of aluminium and aluminium alloys - Determination of manganese (volumetric: arsenite/nitrite method) |
| BS 1748 Pts.1-5-1961 | 铜合金分析方法.第1部分至第5部分:铜合金中铜、铅、铁、铝和镍的测定方法 | Methods for the analysis of copper alloys - Methods for the determination of copper, lead, iron, aluminium and nickel in copper alloys |
| BS 1748 Pts.11 and 12-1964 | 铜合金分析方法.第11和12部分:含铅青铜合金中铜和铅的测定方法 | Methods for the analysis of copper alloys - Methods for the determination of copper and lead in leaded bronze alloys |
| BS 1748-6-1960 | 铜合金分析方法.第6部分:铜合金中锡的测定方法(镍线圈还原法) | Methods for the analysis of copper alloys - Method for the determination of tin in copper alloys (nickel coil reduction method) |
| BS 1748-7-1960 | 铜合金分析方法.第7部分:铜合金中硅的测定方法(光度测量法) | Methods for the analysis of copper alloys - Method for the determination of silicon in copper alloys (photometric method) |
| BS 1748-8-1960 | 铜合金分析方法.第8部分:铜合金中磷的测定方法(光度测量法） | Methods for the analysis of copper alloys - Method for the determination of phosphorus in copper alloys (photometric method) |
| BS 1748-9-1963 | 铜合金分析方法.第9部分:铜合金中锌的测定方法 | Methods for the analysis of copper alloys - Method for the determination of zinc in copper alloys |
| BS 1974-1953 | 铝合金大铆钉(标称直径1/2英寸至1英寸)规范 | Specification for large aluminium alloy rivets (1/2 in. to 1 in. nominal diameters) |
| BS 2000-137-1993 | 石油和石油产品的试验方法.水混合金属加工油稀释液中油含量的测定 | Methods of test for petroleum and its products - Determination of oil content of water mix metalworking oil dilutions |
| BS 2000-414-1996 | 石油和石油产品试验方法.第414部分;工业淬火油.冷却特性测定.镍合金探头试验法 | Methods of test for petroleum and its products - Industrial quenching oils - Determination of cooling characteristics - Nickel-alloy probe test method |
| BS 2051-1-1973 | 工程用管与管接头规范.第1部分:工程用铜与铜合金毛细管与耐压管接头 | Tube and pipe fittings for engineering purposes - Copper and copper alloys capillary and compression tube fittings for engineering purposes |
| BS 2051-2-1984 | 工程用管与管接头规范.第2部分:橄榄型铜合金耐压管接头 | Tube and pipe fittings for engineering purposes - Specification for olive type copper alloy compression tube fittings |
| BS 2593-1974 | 旋转钻杆与碳化钨硬质合金旋转钻头规范 | Specification for rotary drill rods and tungsten carbide tipped rotary drill bits |
| BS 2767-1991 | 散热器用手动控制铜合金阀的规范 | Specification for manually operated copper alloy valves for radiators |
| BS 2816-1989 | 工程用银和银合金电镀层的规范方法 | Method for specifying electroplated coatings of silver and silver alloys for engineering purposes |
| BS 2A 175-1962 | 飞行器用100°埋头铝合金螺栓(统一螺纹)规范 | Specification for 100 ° countersunk head aluminium alloy bolts (Unified threads) for aircraft |
| BS 2A 29-1962 | 飞行器用铝合金六角螺母(B.A和B.S.F螺纹)(普通和开槽的)规范 | Specification for aluminium alloy hexagonal nuts (B.A and B.S.F. threads) (ordinary and slotted) for aircraft |
| BS 2A 61-1962 | 飞行器用铝合金制六角头螺栓(B.A和B.S.F螺纹)规范 | Specification for aluminium alloy hexagonal headed bolts (B.A. and B.S.F. threads) for aircraft |
| BS 2B 25-2001 | 铜镍硅合金棒材、型材、锻坯、锻件和零件(热处理) | Copper-nickel-silicon alloy rods, sections, forging stock, forgings and parts (heat treated) |
| BS 2B 26-2001 | 铜镍硅合金棒材、型材和零件(固溶处理、冷加工的和沉淀处理) | Copper-nickel-silicon alloy rods, sections and parts (solution treated, cold worked and precipitation treated) |
| BS 2B 27-2002 | 铜锌铝镍硅合金管材 | Copper-zinc-aluminium-nickel-silicon alloy tube |
| BS 2B 28-2001 | 铜铍合金带材、箔及零件(固溶处理和沉淀处理) | Copper-beryllium alloy strip, foil and parts (solution treated and precipitation treated) |
| BS 2B 29-2001 | 铜铍合金带材、箔及零件(溶液处理、冷轧:低硬度和(固溶处理，冷轧：四分之一硬度和沉淀处理) | Copper-beryllium alloy strip, foil and parts (solution treated, cold rolled: quarter hard and precipitation treated) |
| BS 2B 30-2001 | 铜铍合金带材、箔及零件(固溶处理、冷轧:：半硬度和沉淀处理) | Copper-beryllium alloy strip, foil and parts (solution treated, cold rolled: half hard and precipitation treated) |
| BS 2B 31-2001 | 铜铍合金带材、箔及零件(固溶处理、冷轧:全硬度和沉淀处理) | Copper-beryllium alloy strip, foil and parts (solution treated, cold rolled: full hard and precipitation treated) |
| BS 2B 32-2001 | 铜铍合金棒材、型材及零件(固溶处理和沉淀处理) | Copper-beryllium alloy rods, sections and parts (solution treated and precipitation treated) |
| BS 2B 33-2001 | 铜铍合金丝材及弹簧(固溶处理和沉淀处理) | Copper-beryllium alloy wire and springs (solution treated and precipitation treated) |
| BS 2G 238-1996 | 普通机体或设备互连用(260℃)镀镍铜和铜合金导线绕扎绝缘电缆规范 | Specification for electric cables for general airframe or equipment interconnect use (260 °C), nickel plated copper and copper alloy conductors, with wrapped insulation |
| BS 2HC 203-1989 | 镍-铬-铝-钼-铌合金铸件规范(镍基铬13.0、铝6.0、钼4.5、铌2.3) | Specification for nickel-chromium-aluminium-molybdenum-niobium alloy castings (Nickel base Cr 13.0, Al 6.0, Mo 4.5, Nb 2.3) |
| BS 2HC 204-1989 | 镍-钴-铬-铝-钛-钼合金铸件规范(镍基钴15.0、铬10.0、铝5.5、钛4.8、钼3.0) | Specification for nickel-cobalt-chromium-aluminium-titanium-molybdenum alloy castings (Nickel base Co 15.0, Cr 10.0, Al 5.5, Ti 4.8, Mo 3.0) |
| BS 2HC 207-1989 | 镍-钴-钨-铬-铝-钽-铪-钛合金铸件规范(镍基钴10.0、钨10.0、铬9.0、铝5.5、钽25、铪1.5、钛1.5) | Specification for nickel-cobalt-tungsten-chromium-aluminium-tantalum-hafnium-titanium alloy castings (Nickel base Co 10.0, W 10.0, Cr 9.0, Al 5.5, Ta 2.5, Hf 1.5, Ti 1.5) |
| BS 2HC 208-1989 | 镍-钴-钨-铬-铝-钼-钛-钽合金铸件规范(镍基钴10.0、钨10.0、铬9.0、铝5.5、钼2.5、钛1.5、钽1.5) | Specification for nickel-cobalt-tungsten-chromium-aluminium-molybdenum-titanium-tantalu m alloy castings (nickel base Co 10.0, W 10.0, Cr 9.0, Al 5.5, Mo 2.5, Ti 1.5, Ta 1.5) |
| BS 2HC 209-1989 | 低碳、沉淀硬化镍-铬-铝-钼-铌合金铸件规范(镍基铬11.5、铝6.0、钼4.0、铌2.0) | Specification for low carbon, precipitation hardening nickel-chromium-aluminium-molybdenum-niobium alloy castings (Nickel base Cr 11.5, Al 6.0, Mo 4.0, Nb 2.0) |
| BS 2HC 210-1989 | 镍-钨-铝-铬-钼合金铸件规范(镍基钨10.5、铝6.0、铬6.0、钼2.0) | Specification for nickel-tungsten-aluminium-chromium-molybdenum alloy castings (Nickel base W 10.5, Al 6.0, Cr 6.0, Mo 2.0) |
| BS 2HC 211-1989 | 镍-铬-钴-钼-铝钛合金铸件规范(镍基铬15.5、钴10.0、钼8.3、铝4.2、钛3.6) | Specification for nickel-chromium-cobalt-molybdenum-aluminium-titanium alloy castings (Nickel base Cr 15.5, Co 10.0, Mo 8,3, Al 4.2, Ti 3.6) |
| BS 2HR 1-1973 | 镍-铬-钛铝耐热合金坯锭、棒材、锻件和部件(镍基、Cr 19.5、Ti 2.2、Al 1.4)规范 | Specification for nickel-chromium-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 19.5, Ti 2.2, Al 1.4) |
| BS 2HR 2-1973 | 镍-铬-钛-铝耐热合金坯锭、棒材、锻件和部件(镍基、Cr 19.5、Co18.0、Ti25、Al 1.5)规范 | Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5) |
| BS 2HR 201-1974 | 镍-铬-钛-铝耐热合金板材、薄板材和带材(镍基、Cr19.5、Ti2.2、Al1.4)规范 | Specification for nickel-chromium-titanium-aluminium heat-resisting alloy plate, sheet and strip (nickel base, Cr 19.5, Ti 2.2, Al 1.4) |
| BS 2HR 202-1973 | 镍-铬-钴-钛耐热合金薄板材和带材(镍基、Cr19.5、Co18.0、Ti2.5、Al 1.5)规范 | Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy sheet and strip (nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5) |
| BS 2HR 401-1973 | 冷加工和软化的无缝镍铬钛铝耐热合金管(镍基、Cr 19.5、Ti 2.2、Al 1.4)规范 | Specification for nickel-chromium-titanium-aluminium heat-resisting alloy cold worked and softened seamless tubes (nickel base, Cr 19.5, Ti 2.2, Al 1.4) |
| BS 2HR 501-1973 | 弹簧用冷拉固溶热处理的镍铬钴钛铝耐热合金线材(镍基、Cr19.5、Co18.0、Ti2.5、Al 1.5)规范 | Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy cold drawn wire for springs (nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5) |
| BS 2HR 502-1973 | 弹簧用冷拉和固溶热处理的镍铬钴钛铝耐热合金线材(镍基、Cr19.5、Co18.0、Ti2.5、Al 1.5)规范 | Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy cold drawn and solution heat treated wire for springs (nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5) |
| BS 2HR 503-1973 | 螺纹垫圈(直径0.45mm-2mm)用镍铬钴钛铝耐热合金线材(镍基、Cr19.5、Co18.0、Ti2.5、Al 1.5)规范 | Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy wire for thread inserts (0.45 mm to 2 mm diameter) (nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5) |
| BS 2HR 504-1973 | 镍-铬-钛耐热合金棒材、线材和铆钉(镍基、Cr19.5、Ti0.4)规范 | Specification for nickel-chromium-titanium heat-resisting alloy bar, wire and rivets (nickel base, Cr 19.5, Ti 0.4) |
| BS 2L 126-1970 | 镁-铈（稀土金属）(3.0)-锌(2.3)-锆(0.6)合金铸锭和铸件规范(沉淀处理) | Specification for ingots and castings of magnesium-cerium-zinc-zirconium alloy (precipitation treated) (rare earth metals 3.0, Zn 2.3, Zr 0.6) |
| BS 2L 127-1970 | 镁-锌(4.5)-锆(0.7)合金铸锭和铸件规范(沉淀处理) | Specification for ingots and castings of magnesium-zinc-zirconium alloy (precipitation treated) (Zn 4.5, Zr 0.7) |
| BS 2L 128-1970 | 镁-锌(4.5)-铈（稀土金属）(1.2)-锆(1.7)合金铸锭和铸件规范(沉淀处理) | Specification for ingots and castings of magnesium-zinc-cerium-zirconium alloy (precipitation treated) (Zn 4.5, rare earth metals 1.2, Zr 0.7) |
| BS 2L 169-2002 | 铝-硅-镁合金(Si 7, Mg 0.6)的铸锭和(溶解处理和人工老化的)铸件 | Ingots (as cast) and castings (solution treated and artificially aged) of aluminium-silicon-magnesium alloy (Si 7, Mg 0.6) |
| BS 2L 500-1973 | 可锻制的镁基合金检验和试验规程 | Procedure for inspection and testing of wrought magnesium-base alloys |
| BS 2L 503-1973 | 镁-铝(6)-锌(1.0)合金管规范 | Specification for tube of magnesium-6% aluminium-zinc alloy (Al 6.0, Zn 1.0) |
| BS 2L 504-1973 | 镁-锌(3)-锆(0.6)合金的薄板材和带材规范 | Specification for sheet and strip of magnesium-3% zinc-zirconium alloy (Zn 3.0, Zr 0.6) |
| BS 2L 505-1973 | 镁-锌(3)-锆(0.6)合金棒材和挤压型材规范(直径或较小截面尺寸小于100mm) | Specification for bars and extruded sections of magnesium-3% zinc-zirconium alloy (not exceeding 100 mm diameter or minor sectional dimension) (Zn 3.0, Zr 0.6) |
| BS 2L 508-1973 | 镁-1<1/4>%锌(1.25)-锆(0.6)合金棒材和挤压型材规范(适用于隋性气体保护弧焊技术)(直径不超过50mm或较小截 | Specification for bars and extruded sections of magnesium-11/4% zinc-zirconium alloy (suitable for welding by inert-gas shielded arc techniques) (not exceeding 50 mm diameter or minor sectional dimension) (Zn 1.25, Zr 0.6) |
| BS 2L 509-1973 | 镁-锌(1.25)-锆(0.6)合金管规范(适用于隋性气体保护弧焊技术) | Specification for tube of magnesium-11/4% zinc-zirconium alloy (suitable for welding by inert-gas shielded arc techniques) (Zn 1.25 , Zr 0.6) |
| BS 2L 77-1971 | 铝-铜(4.4)-镁(0.5)-硅(0.7)-锰(0.8)合金锻坯和锻件的规范(溶解和沉淀处理) | Specification for forging stock and forgings of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and precipitation treated) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) |
| BS 2L 83-1971 | 铝-铜(2)-镍(1)-镁(1)-铁(0.9)-硅(0.9)合金锻坯、棒材、挤压型材和锻件规范(溶解处理和沉淀处理) | Specification for forging stock, bars, extruded sections and forgings of aluminium-copper-nickel-magnesium-iron-silicon alloy (solution treated and precipitation treated) (Cu 2, Ni 1, Mg 1, Si 0.9, Fe 0.9) |
| BS 2L 85-1971 | 铝-铜(1.5)-硅(1)和镁(0.8)合金锻坯、棒材、挤压型材和锻件规范(溶解处理和沉淀处理) | Specification for forging stock, bars, extruded sections and forgings of aluminium-copper-silicon-magnesium alloy (solution treated and precipitation treated) (Cu 1.5, Si 1, Mg 0.8) |
| BS 2L 87-1971 | 用于制造螺母、联轴节和机加工中空零部件的铝-铜(4.4)-镁(0.5)-硅(0.7)-锰(0.8)合金六角棒材规范(固溶处理 | Specification for hexagonal bars for nuts, couplings and hollow machined parts of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and precipitation treated) (free from peripheral and asymmetric coarse grain) (not less than 14 mm nor more than 36 mm across flats) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) |
| BS 2L 93-1971 | 铝-铜(4.4)-镁(0.5)-硅(0.7)-锰(0.8)合金板规范(固溶处理,控制拉伸和沉淀处理) | Specification for plate of aluminium-copper-magnesium-silicon-manganese alloy (solution treated , controlled stretched and precipitation treated) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) |
| BS 2L 95-1971 | 铝-锌(5.8)-镁(2.5)-铜(1.6)-铬(0.15)合金板规范(溶解处理、控制拉伸和沉淀处理) | Specification for plate of aluminium-zinc-magnesium-copper-chromium alloy (solution treated, controlled stretched and precipitation treated) (Zn 5.8, Mg 2.5, Cu 1.6, Cr 0.15) |
| BS 2L 97-1971 | 铝-铜(4.4)-镁(1.5)-锰(0.6)合金中厚板材规范(固溶处理,室温时效:控制拉伸) | Specification for plate of aluminium-copper-magnesium-manganese alloy (solution treated, controlled stretched and aged at room temperature) (Cu 4.4, Mg 1.5, Mn 0.6) |
| BS 2L 98-1971 | 铝-铜(4.4)-镁(1.5)-锰(0.6)合金板规范(溶解处理、室温时效:不控制拉伸的) | Specification for plate of aluminium-copper-magnesium-manganese alloy (solution treated and aged at room temperature: not controlled stretched) (Cu 4.4, Mg 1.5, Mn 0.6) |
| BS 2L 99-1972 | 铝-硅(7)-镁(0.3)合金铸锭和铸件规范(固溶处理和沉淀处理) | Specification for ingots and castings of aluminium-silicon-magnesium alloy (solution treated and precipitation treated) (Si 7, Mg 0.3) |
| BS 2SP 148-150-1979 | 铝合金统一垫圈规范 | Specification for Unified aluminium alloy washers |
| BS 2SP 151-153-1979 | 合金钢统一垫圈规范 | Specification for Unified alloy steel washers |
| BS 2SP 77 to 2SP 80-1973 | 圆头形铝和铝合金铆钉规范 | Specification for snap head aluminium and aluminium alloy rivets |
| BS 2SP 81 and 2SP 82-1973 | 圆头高镍铜合金铆钉规范 | Specification for snap head high nickel-copper alloy rivets |
| BS 2SP 83 to 85-1973 | 菌形头铝合金铆钉规范 | Specification for mushroom head aluminium alloy rivets |
| BS 2SP 87 and 2SP 88-1973 | 100°埋头高镍铜合金铆钉规范 | Specification for 100 ° countersunk head high nickel-copper alloy rivets |
| BS 2TA 10-1974 | 钛铝钒合金薄板材规范(抗拉强度960-1270MPa) | Specification for sheet of titanium-aluminium-vanadium alloy (tensile strength 960-1270 MPa) |
| BS 2TA 100-1973 | 锻造钛和钛合金的检验和试验规程 | Procedure for inspection and testing of wrought titanium and titanium alloys |
| BS 2TA 11-1974 | 机加工用钛铝钒合金棒材和型材规范(抗拉强度900-1160MPa)(限定等圆断面150mm) | Specification for bar and section for machining of titanium-aluminium-vanadium alloy (tensile strength 900-1160 MPa) (limiting ruling section 150 mm) |
| BS 2TA 12-1974 | 钛铝钒合金锻坯规范(抗拉强度900-1160MPa)(限定等圆断面150mm) | Specification for forging stock of titanium-aluminium-vanadium alloy (tensile strength 900-1160 MPa) (limiting ruling section 150 mm) |
| BS 2TA 13-1974 | 钛铝钒合金锻件规范(抗拉强度900-1160MPa)(限定等圆断面150mm) | Specification for forgings of titanium-aluminium-vanadium alloy (tensile strength 900-1160 MPa) (limiting ruling section 150 mm) |
| BS 2TA 21-1973 | 钛铜合金薄板材和带材规范(抗拉强度540-700 N/mm<上标2>) | Specification for sheet and strip of titanium-copper alloy (tensile strength 540-700 MPa) |
| BS 2TA 22-1973 | 机加工钛铜合金棒材和型材规范(抗拉强度540-770 N/mm<上标2>) | Specification for bar and section for machining of titanium-copper alloy (tensile strength 540-770 N/mm2) |
| BS 2TA 23-1973 | 钛铜合金锻坯规范(抗拉强度540-770 N/mm<上标2>) | Specification for forging stock of titanium-copper alloy (tensile strength 540-770 N/mm2) |
| BS 2TA 24-1973 | 钛铜合金锻件规范(抗拉强度540-770 N/mm<上标2>) | Specification for forgings of titanium-copper alloy (tensile strength 540-770 N/mm2) |
| BS 2TA 28-1974 | 钛铝钒合金锻坯和线材规范(抗拉强度1100-1300MPa)(限定等圆断面20mm)(主要供加工符合英国标准A系列要求的紧 | Specification for forging stock and wire of titanium-aluminium-vanadium alloy (tensile strength 1100-1300 MPa) (limiting ruling section 20 mm) (primarily intended for the manufacture of fasteners complying with the requirements of the 'A' series of British Standards) |
| BS 3071-1986 | 镍铜合金铸件规范 | Specification for nickel-copper alloy castings |
| BS 3072-1989 | 镍与镍合金规范:薄板材和中厚板材 | Specification for nickel and nickel alloys: sheet and plate |
| BS 3073-1977 | 镍和镍合金带材规范 | Specification for nickel and nickel alloys: strip |
| BS 3074-1989 | 镍与镍合金无缝管规范 | Specification for nickel and nickel alloys: seamless tube |
| BS 3075-1976 | 镍与镍合金线材规范 | Specification for nickel and nickel alloys: wire |
| BS 3076-1989 | 镍与镍合金棒材规范 | Specification for nickel and nickel alloys: bar |
| BS 3146-1-1974 | 金属熔模铸造规范.第1部分:碳素钢与低合金钢 | Specification for investment castings in metal - Carbon and low alloy steels |
| BS 3146-2-1975 | 金属熔模铸造规范.第2部分:耐蚀耐热钢、镍和钴基合金 | Specification for investment castings in metal - Corrosion and heat resisting steels, nickel and cobalt base alloys |
| BS 3332-1987 | 轴承用巴比合金锭规范 | Specification for white metal bearing alloy ingots |
| BS 3338-10-1961 | 锡及锡合金取样及分析方法.第10部分:锡锭、锡铅焊料及轴承用巴比合金中铁含量测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of iron in ingot tin, tin-lead solders and white metal bearing alloys (photometric method) |
| BS 3338-11-1961 | 锡及锡合金取样及分析方法.第11部分:焊料中锡含量测定方法(镍带卷还原法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of tin in solders (nickel coil reduction method) |
| BS 3338-13-1965 | 锡及锡合金取样及分析方法.第13部分:焊料及轴承用巴比合金中锑含量测定方法(溴酸钾容量法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of antimony in solders and white metal bearing alloys (volumetric: potassium bromate method) |
| BS 3338-14-1965 | 锡及锡合金的取样及分析方法.第14部分:轴承用巴比合金锭取样方法 | Methods for the sampling and analysis of tin and tin alloys - Method for the sampling of white metal bearing alloy ingots |
| BS 3338-15-1965 | 锡及锡合金取样及分析方法.第15部分:轴承用巴比合金中铜和铅含量测定方法(电解镀层法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of copper and lead in white metal bearing alloys (electrodeposition method) |
| BS 3338-16-1965 | 锡及锡合金取样及分析方法.第16部分:轴承用巴比合金中锡含量测定方法(镍带卷还原法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of tin in white metal bearing alloys (nickel coil reduction method) |
| BS 3338-17-1965 | 锡及锡合金的取样及分析方法.第17部分:焊料及轴承用巴比合金中镉含量测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of cadmium in solders and white metal bearing alloys (photometric method) |
| BS 3338-18-1966 | 锡及锡合金取样及分析方法.第18部分:焊料及轴承用白合金中铝含量测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of aluminium in solders and white metal bearing alloys (photometric method) |
| BS 3338-19-1966 | 锡及锡合金的取样及分析方法.白金属轴承合金和钎料中锌的测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of zinc in solders and white metal bearing alloys (photometric method) |
| BS 3338-1966 | 锡及锡合金的取样及分析方法.第19部分:焊料及白合金轴承中锌的测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys. Method for the determination of zinc in solders and white metal bearing alloys (photometric method) |
| BS 3338-2-1961 | 锡及锡合金取样及分析方法.第2部分:锡锭中锡含量测定方法(铝还原法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of tin in ingot tin (aluminium reduction method) |
| BS 3338-20-1970 | 锡及锡合金取样及分析方法.第20部分:浇灌金属中镍含量测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of nickel in capping metal (photometric method) |
| BS 3338-21-1983 | 锡及锡合金取样及分析方法.第21部分:软焊料中高镉含量测定方法 | Methods for the sampling and analysis of tin and tin alloys - Determination of high cadmium content of soft solders |
| BS 3338-3-1961 | 锡及锡合金取样及分析方法.第3部分:锡锭中锑含量测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of antimony in ingot tin (photometric method) |
| BS 3338-4-1961 | 锡及锡合金取样及分析方法.第4部分:锡锭及锡铅焊料中铜的测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of copper in ingot tin and tin-lead solders (photometric method) |
| BS 3338-5-1961 | 锡及锡合金取样及分析方法.第5部分:锡锭及锡锑焊料中铅含量测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of lead in ingot tin and tin-antimony solders (photometric method) |
| BS 3338-6-1961 | 锡及锡合金取样及分析方法.第6部分:高纯度锡锭中铜的测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of copper in high purity ingot tin (photometric method) |
| BS 3338-7-1961 | 锡及锡合金取样及分析方法.第7部分:焊料中银含量测定方法(硫氰酸铵容量法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of silver in solders (volumetric: ammonium thiocyanate method) |
| BS 3338-8-1961 | 锡及锡合金取样及分析方法.第8部分:锡锭、锡铅焊料及轴承用巴比合金中铋含量测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of bismuth in ingot tin, tin-lead solders and white metal bearing alloys (photometric method) |
| BS 3338-9-1965 | 锡及锡合金取样及分析方法.第9部分:锡锭、焊料及轴承用巴比合金中砷含量测定方法(光度测定法) | Methods for the sampling and analysis of tin and tin alloys - Method for the determination of arsenic in ingot tin, solders and white metal bearing alloys (photometric method) |
| BS 3382 Pts.3 and 4-1965 | 螺纹部件的电镀层规范.第3部分:钢制部件的镍或镍铬镀层.第4部分:铜及铜合金(包括黄铜)部件的镍或镍铬镀层 | Specification for electroplated coatings on threaded components - Nickel or nickel plus chromium on steel components - Nickel or nickel plus chromium on copper and copper alloy (including brass) components |
| BS 3382 Pts.5 and 6-1967 | 螺纹部件的电镀层规范.第5部分:铜和铜合金(包括黄铜)部件的锡镀层.第6部分:铜和铜合金(包括黄铜)部件的银镀 | Specification for electroplated coatings on threaded components - Tin on copper and copper alloy (including brass) components - Silver on copper and copper alloy (including brass) components |
| BS 3467-1962 | 精密电阻器合金丝电阻温度系数试验方法 | Method of test for temperature coefficient of resistance of alloy wire for precision resistors |
| BS 3520-1962 | 牙科用精制贵金属合金丝规范 | Specification for dental wrought precious metal alloy wire |
| BS 3551-1962 | 合金钢锁扣规范 | Specification for alloy steel shackles |
| BS 3597-1984 | 65/35锡/镍合金电镀层规范 | Specification for electroplated coatings of 65/35 tin/nickel alloy |
| BS 3604-2-1991 | 承压钢管.具有规定高温特性的铁合金钢.第2部分:纵向电弧焊接管规范 | Steel pipes and tubes for pressure purposes: ferritic alloy steel with specified elevated temperature properties - Specification for longitudinally arc welded tubes |
| BS 3630-16-1976 | 锌和锌合金的取样与分析方法.第16部分:锌合金中镍含量(光度测量法) | Methods for the sampling and analysis of zinc and zinc alloys - Nickel in zinc alloys (photometric method) |
| BS 3821-1-1974 | 硬质合金模具和配套硬质合金工具规范.第1部分:烧结模坯和精加工模名称与标记 | Specification for hardmetal dies and associated hardmetal tools - Designation and marking of as-sintered pellets and finished dies |
| BS 3821-2-1974 | 硬质合金模具和配套硬质合金工具规范.第2部分:拉制圆金属丝用烧结模坯和精加工模 | Specification for hardmetal dies and associated hardmetal tools - As-sintered pellets and finished dies for drawing round wire |
| BS 3821-3-1974 | 硬质合金模具和配套硬质合金工具规范.第3部分:拉制圆棒材用烧结模坯和精加工模 | Specification for hardmetal dies and associated hardmetal tools - As-sintered pellets and finished dies for drawing round bar |
| BS 3821-4-1982 | 硬质合金模具和配套硬质合金工具规范.第4部分:顶锻模用硬质合金烧结模坯尺寸和公差 | Specification for hardmetal dies and associated hardmetal tools - Dimensions and tolerances of as-sintered hardmetal pellets used in heading dies |
| BS 3907-1-1965 | 镁和镁合金分析方法.第1部分:镁合金中铝含量测定(重量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of aluminium in magnesium alloys (gravimetric method) |
| BS 3907-10-1969 | 镁和镁合金分析方法.第10部分:含稀土元素锆、钍和(或)银的镁合金中锰含量测定(光度测量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of manganese in magnesium alloys containing zirconium, rare earths, thorium and/or silver (photometric method) |
| BS 3907-11-1970 | 镁和镁合金分析方法.第11部分:硅含量测定(光度测量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of silicon in magnesium and magnesium alloys (photometric method) |
| BS 3907-12-1971 | 镁和镁合金分析方法.第12部分:铝含量测定(光度测量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of aluminium in magnesium and magnesium alloys (photometric method) |
| BS 3907-13-1972 | 镁和镁合金分析方法.第13部分:锡含量测定(光度测量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of tin in magnesium and magnesium alloys (photometric method) |
| BS 3907-15-1976 | 镁和镁合金分析方法.第15部分:铅含量测定(原子吸收法) | Methods for the analysis of magnesium and magnesium alloys - Determination of lead in magnesium and magnesium alloys (atomic absorption method) |
| BS 3907-2-1966 | 镁和镁合金分析方法.第2部分:铁含量测定(1:10-菲绕啉光度测量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of iron in magnesium and magnesium alloys (photometric - 1:10-phenanthroline method) |
| BS 3907-3-1966 | 镁和镁合金的分析方法.第3部分:镁和镁合金中铜含量的测定(光度测量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of copper in magnesium and magnesium alloys (photometric method) |
| BS 3907-4-1966 | 镁和镁合金分析方法.第4部分:锰含量测定(高碘酸盐光度测量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of manganese in magnesium and magnesium alloys (photometric-periodate method) |
| BS 3907-5-1966 | 镁和镁合金分析方法.第5部分:低锰含量测定(高碘酸盐光度测量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of manganese in magnesium and magnesium alloys (photometric-periodate method) (low contents) |
| BS 3907-6-1969 | 镁和镁合金分析方法.第6部分:锆含量测定(光度测量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of zirconium in magnesium and magnesium alloys (photometric method) |
| BS 3907-7-1969 | 镁和镁合金分析方法.第7部分:镁合金中镍含量测定(光度法) | Methods for the analysis of magnesium and magnesium alloys - Determination of nickel in magnesium alloys (photometric method) |
| BS 3907-8-1970 | 镁和镁合金分析方法.第8部分:镁合金中全部稀土族元素含量测定 | Methods for the analysis of magnesium and magnesium alloys - Determination of total rare earths in magnesium alloys (gravimetric method) |
| BS 3907-9-1969 | 镁和镁合金分析方法.第9部分:镁合金中锌含量测定(乙二胺四醋酸离子置换容积测量法) | Methods for the analysis of magnesium and magnesium alloys - Determination of zinc in magnesium alloys (ion-exchange-volumetric EDTA method) |
| BS 3908-10-1989 | 铅和铅合金取样与分析方法.第10部分:铅合金中锑含量测定(滴定法) | Methods for the sampling and analysis of lead and lead alloys - Antimony in lead alloys (titrimetric method) |
| BS 3908-13-1970 | 铅和铅合金取样与分析方法.第13部分:少量锑含量的测定(光度测量法) | Methods for the sampling and analysis of lead and lead alloys - Antimony in lead and lead alloys (low contents) (photometric method) |
| BS 3908-2-1967 | 铅和铅合金取样与分析方法.第2部分:砷含量测定(光度测量法) | Methods for the sampling and analysis of lead and lead alloys - Arsenic in lead and lead alloys (photometric method) |
| BS 3908-6-1971 | 铅和铅合金取样与分析方法.第6部分:碲含量测定(光度测量法) | Methods for the sampling and analysis of lead and lead alloys - Tellurium in lead and lead alloys (photometric method) |
| BS 3908-9-1991 | 铅和铅合金取样和分析方法.第9部分:硫含量测定 | Methods for the sampling and analysis of lead and lead alloys - Sulphur in lead and lead alloys |
| BS 3A 107-1962 | 飞行器用铝合金螺母(统一六角形和统一螺纹)(普通和开槽的)规范 | Specification for aluminium alloy nuts (Unified hexagons and Unified threads) (ordinary and slotted) for aircraft |
| BS 3A 171-1962 | 飞行器铝合金盘头螺栓(统一螺纹)规范 | Specification for aluminium alloy pan head bolts (Unified threads) for aircraft |
| BS 3HR 100-1978 | 可锻耐热合金的检验和试验规程 | Procedure for inspection and testing of wrought heat-resisting alloys |
| BS 3HR 601-1989 | 紧固件制造用(最大直径或小截面尺寸为30mm)镍-铬-钛-铝耐热合金棒材和线材(镍基铬19.5、钛2.2、铝1.4)规范 | Specification for nickel-chromium-titanium-aluminium heat-resisting alloy bar and wire for the manufacture of fasteners (maximum diameter or minor sectional dimension 30 mm) (nickel base Cr 19.5, Ti 2.2, Al 1.4) |
| BS 3L 122-1970 | 镁-铝(8)-锌(0.5)-锰(0.3)合金铸锭和铸件规范(固溶处理) | Specification for ingots and castings of magnesium-8% aluminium-zinc-manganese alloy (solution treated) (Al 8, Zn 0.5, Mn 0.3) |
| BS 3L 124-1970 | 镁-铝(10)-锌(0.5)-锰(0.3)合金铸锭和铸件规范(溶液处理) | Specification for ingots and castings of magnesium - 10% aluminium-zinc-manganese alloy (solution treated) (Al 10, Zn 0.5, Mn 0.3) |
| BS 3L 125-1970 | 镁-铝(10)-锌(0.5)-锰(0.3)合金铸锭和铸件规范(溶液处理和沉淀处理) | Specification for ingots and castings of magnesium - 10% aluminium-zinc-manganese alloy (solution treated and precipitation treated) (Al 10, Zn 0.5, Mn 0.3) |
| BS 3L 51-1970 | 铝-硅(2.5)-铜(1.2)-镍(1.0)-镁(0.1)-铁(1.0)合金铸锭和铸件规范(沉淀热处理) | Specification for ingots and castings of aluminium-silicon-copper-iron-nickel-magnesium alloy (precipitation treated) (Si 2.5, Cu 1.2, Fe 1, Ni 1, Mg 0.1) |
| BS 3L 63-1971 | 铝-铜-(4.4)-镁(0.5)-硅(0.7)-锰(0.8)合金管规范(溶解和沉淀处理) | Specification for tube of aluminium-copper-mangesium-silicon-manganese alloy (solution treated and precipitation treated) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) |
| BS 3L 78-1970 | 铝-硅(5)-铜(1.2)-镁(0.5)合金铸锭和铸件规范(固溶处理和热处理) | Specification for ingots and castings of aluminium-silicon-copper-magnesium alloy (solution treated and precipitation treated) (Si 5, Cu 1.2, Mg 0.5) |
| BS 3L 80-1985 | 铝-镁2.25%合金板材和带材规范(强度符号-0) | Specification for sheet and strip of aluminium-21/4% magnesium alloy (temper designation-O) |
| BS 3L 81-1985 | 铝-镁2.25%合金板材和带材规范(强度符号-H16或H26) | Specification for sheet and strip of aluminium-21/4% magnesium alloy (temper designation H16 or H26) |
| BS 3L 86-1971 | 铝-铜(2.5)-镁(0.3)合金冷锻实心铆钉用钢丝规范(直径不超过10mm) | Specification for wire for solid, cold-forged rivets of aluminium-copper-magnesium alloy (not exceeding 10 mm diameter) (Cu 2.5, Mg 0.3) |
| BS 3SP 168-169-2002 | 航空航天用的编织橡胶绳组件的外用套管和组合金属丝 | Ferrules and assembly wires for braided rubber cord assemblies for aerospace use |
| BS 4048 Pts.1 & 2-1966 | 复合金属丝绳索和纤维绳索规范.第1部分:复合绳索.第2部分:弹性绞索 | Specification for combined wire and fibre ropes. Combined ropes. Spring lay ropes |
| BS 4193-10-1982 | 镶硬质合金刀具.第10部分:带可转位刀片和莫氏锥柄的端铣刀规范 | Hardmetal insert tooling - Specification for end mills with indexable inserts and Morse taper shank |
| BS 4193-11-1983 | 镶硬质合金刀具.第11部分:带可转位刀片的平面铣刀尺寸规范 | Hardmetal insert tooling - Specification for dimensions of face milling cutters with indexable inserts |
| BS 4193-12-1984 | 镶硬质合金刀具.第12部分:带可转位刀片的侧铣刀及端铣刀和切槽刀尺寸规范 | Hardmetal insert tooling - Specification for dimensions of side and face milling and slotting cutters with indexable inserts |
| BS 4193-13-1998 | 硬质合金镶齿工具.第13部分:带圆角可转位硬质金属镶齿.部分圆柱型固定孔.尺寸 | Hardmetal insert tooling - Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole - Dimensions |
| BS 4193-14-1997 | 镶硬质合金刀具.第14部分:可转位刀片用镗杆(圆柱柄刀夹)命名规范 | Hardmetal insert tooling - Specification for designation of boring bars (tool holders with cylindrical shank) for indexable inserts |
| BS 4193-15-1986 | 镶硬质合金刀具.第15部分:无固定孔的可转位刮棱硬质合金刀片尺寸规范 | Hardmetal insert tooling - Specification for dimensions for indexable hardmetal (carbide) inserts with wiper edges but without fixing hole |
| BS 4193-16-1986 | 镶硬质合金刀具.第16部分:可转位刀片用柄式铣刀命名规范 | Hardmetal insert tooling - Specification for designation of shank type milling cutters for indexable inserts |
| BS 4193-17-1989 | 镶硬质合金刀具.第17部分:可转位刀片用膛孔型铣刀命名规范 | Hardmetal insert tooling - Specification for designation of bore type milling cutters for indexable inserts |
| BS 4193-18-1997 | 镶硬质合金刀具.第18部分:可转位刀片用膛杆尺寸规范 | Hardmetal insert tooling - Specification for dimensions of boring bars for indexable inserts |
| BS 4193-18-1999 | 硬质合金刀具.可分刻度的镶嵌刀片的镗杆尺寸规范 | Hardmetal insert tooling - Specification for dimensions of boring bars for indexable inserts |
| BS 4193-19-1993 | 镶硬质合金刀具.无固定孔的圆角的可转位陶瓷镶装刀片的尺寸规范 | Hardmetal insert tooling - Specification for dimensions of indexable ceramic inserts with rounded corners without fixing hole |
| BS 4193-1993 | 镶硬质合金刀具.第19部分:无固定孔圆角可分度陶瓷刀片尺寸规范 | Hardmetal insert tooling. Specification for dimensions of indexable ceramic inserts with rounded corners without fixing hole |
| BS 4193-2-1986 | 镶硬质合金刀具.第2部分:无固定孔的圆角可转位硬质合金(碳化物)刀片尺寸规范 | Hardmetal insert tooling - Specification for dimensions for indexable hardmetal (carbide) inserts with rounded corners, without fixing hole |
| BS 4193-20-1993 | 镶硬质合金刀具.第20部分:有固定孔圆角可转位陶瓷刀片尺寸规范 | Hardmetal insert tooling - Specification for dimensions of ceramic inserts with rounded corners with fixing hole |
| BS 4193-21-1993 | 镶硬质合金刀具.第21部分:带可转位硬质合金镶刃的直柄钻头规范 | Hardmetal insert tooling - Specification for cylindrical shanks with a parallel flat for drills with indexable inserts |
| BS 4193-22-1996 | 镶硬质合金刀具.第22部分:带断屑器的分度刀片近似切屑控制范围分类和设计 | Hardmetal insert tooling - Classification and designation of approximate chip control zones for indexable inserts with chipbreakers |
| BS 4193-3-1997 | 镶硬质合金刀具.第3部分:带圆柱圆定孔和圆角可分度硬质合金(碳化物)刀片尺寸规范 | Hardmetal insert tooling - Specification for dimensions of indexable hardmetal (carbide) inserts with rounded corners and with cylindrical fixing hole |
| BS 4193-6-1997 | 镶硬质合金刀具.第6部分:可转位(多刃)刀片用旋转夹和仿形刀夹及卡盘命名规范 | Hardmetal insert tooling - Specification for the designation of turning and copying tool holders and cartridges for indexable (throwaway) inserts |
| BS 4193-7-1999 | 硬质合金刀具.可转位刀片车削和仿形用单刃刀具夹.尺寸 | Hardmetal insert tooling - Single point tool holders for turning and copying for indexable inserts - Dimensions |
| BS 4193-8-1997 | 镶硬质合金刀具.第8部分:可转位(多刃)刀用A 型卡盘尺寸规范 | Hardmetal insert tooling - Specification for dimensions for type A cartridges for indexable (throwaway) inserts |
| BS 4193-9-1982 | 镶硬质合金刀具.第9部分:带可转位刀片和扁平直柄的端铣刀规范 | Hardmetal insert tooling - Specification for end mills with indexable inserts and flatted parallel shank |
| BS 4290-1989 | 装饰或保护用银和银合金电镀层的规范方法 | Method for specifying electroplated coatings of silver and silver alloys for decorative and protective purposes |
| BS 4292-1-1989 | 金与金合金电镀层规定方法.第1部分:工程用金与金合金 | Method for specifying electroplated coatings of gold and gold alloys - Gold and gold alloys for engineering purposes |
| BS 4292-2-1989 | 金和金合金电镀层规定方法.第2部分:装饰或保护用金和金合金 | Method for specifying electroplated coatings of gold and gold alloys - Gold and gold alloys for decorative and protective purposes |
| BS 4300/10-1969 | 普通工程用锻造铝和铝合金规范(补充系列).第10部分:5454型冷拔管 | Wrought aluminium and aluminium alloys for general engineering purposes (supplementary series) - 5454 Drawn tube |
| BS 4480-3-1993 | 滑动轴承.米制系列.第3部分:铜合金套管 | Plain bearings: metric series - Copper alloy bushes |
| BS 4486-1980 | 混凝土预加应力用热轧和热轧并处理的高抗拉强度的合金钢筋规范 | Specification for hot rolled and hot rolled and processed high tensile alloy steel bars for the prestressing of concrete |
| BS 4842-1984 | 凃用于外部建筑的铝合金挤压件、薄板材和预成型件上的液态有机涂层和液态有机涂层的规范 | Specification for liquid organic coatings for application to aluminium alloy extrusions, sheet and preformed sections for external architectural purposes, and for the finish on aluminium alloy extrusions, sheet and preformed sections coated with liquid organic coatings |
| BS 4872-2-1976 | 不要求批准焊接工艺时焊工的鉴定考试规范.第2部分:铝及铝合金钨极惰性气体保护电弧焊或熔化极惰性气体保护 | Specification for approval testing of welders when welding procedure approval is not required - TIG or MIG welding of aluminium and its alloys |
| BS 4873-2004 | 铝合金窗 | Aluminium alloy windows |
| BS 4A 169-2002 | 飞行器用铝合金螺栓(统一六角形和统一螺纹) | Specification for aluminium alloy bolts (Unified hexagons and Unified threads) for aircraft |
| BS 4A 170-1999 | 铝合金蘑菇头开槽螺栓(统一螺纹)规范 | Specification for aluminium alloy, mushroom-headed, slotted drive, bolts (unified thread) |
| BS 4L 100-1993 | 锻铝和铝合金的检验、试验和验收程序 | Procedure for inspection, testing and acceptance of wrought aluminium and aluminium alloys |
| BS 4L 56-1986 | 铝-2<1/4>%镁合金管规范(强度符号-O)(无缝管:液压试验)(壁厚不超过12mm) | Specification for tube of aluminium-21/4% magnesium alloy (temper designation-O) (seamless: tested hydraulically) (not exceeding 12 mm wall thickness) |
| BS 4L 59-1985 | 铝-镁合金板材和带材规范(强度符号-H16或H2) | Specification for sheet and strip of aluminium-manganese alloy (temper designation H16 or H26) |
| BS 4L 60-1985 | 铝-镁合金板材和带材规范(强度符号-H12或H22) | Specification for sheet and strip of aluminium-manganese alloy (temper designation H12 or H22) |
| BS 4L 61-1985 | 铝-镁合金板材和带材规范(强度符号-0) | Specification for sheet and strip of aluminium-manganese alloy (temper designation-O) |
| BS 5045-8-2000 | 可运输的气瓶.特殊便携的在15℃时最高达300巴充气压力的水容量为0.5L-15L的无缝铝合金气瓶规范 | Transportable gas containers - Specification for seamless aluminium alloy gas containers of water capacity 0.5 L up to 15 L and up to 300 bar charged pressure at 15 °C for special portable application |
| BS 5117-2.6-1992 | 发动机浓缩冷却剂(防冻剂)腐蚀抑制试验.第2部分:防腐蚀性能试验方法.第6节:热传导条件下铸铝合金防腐蚀试验 | Testing corrosion inhibiting, engine coolant concentrate ('antifreeze') - Methods of test for corrosion inhibition performance - Test for corrosion of cast aluminium alloys under heat-transfer conditions |
| BS 5154-1991 | 铜合金球形阀、球形截流和止回阀、止回和闸阀规范 | Specification for copper alloy globe, globe stop and check, check and gate valves |
| BS 5338-1976 | 工程用锌合金压模铸件实用规程 | Code of practice for zinc alloy pressure die casting for engineering |
| BS 5383-1986 | 采用连续字符标记法的钢镍合金及钛合金管材标志与钢管颜色编码规范 | Specification for material identification of steel, nickel alloy and titanium alloy tubes by continuous character marking and colour coding of steel tubes |
| BS 5599-1993 | 工程用铝及其合金强阳极氧化涂层规范 | Specification for hard anodic oxidation coatings on aluminium and its alloys for engineering purposes |
| BS 5600-3.6-1988 | 粉末冶金材料和制品.第3部分:烧结金属材料和制品（不包活硬质合金）试验方法.第6节:液体渗透率测定 | Powder metallurgical materials and products - Methods of testing sintered metal materials and products, excluding hardmetals - Determination of fluid permeability |
| BS 5624-1978 | 化学加工用容器与设备衬里实用规程.铜和铜合金 | Code of practice for the lining of vessels and equipment for chemical processes: copper and copper alloys |
| BS 5812-1-1979 | 滑动轴承材料.第1部分:整体轴承用铝合金规范 | Materials for plain bearings - Specification for aluminium alloy for solid bearings |
| BS 5L 44-1985 | 铝-镁2(1/4)合金锻坯、棒材、挤压型材和锻件规范 | Specification for forging stock, bars, extruded sections and forgings of aluminium-21/4% magnesium alloy |
| BS 6137-1982 | 锡铅合金电镀层规范 | Specification for electroplated coatings of tin/lead alloys |
| BS 6161-11-1985 | 铝及铝合金阳极氧化镀层试验方法.第11部分:光电反射计测量总反射率 | Methods of test for anodic oxidation coatings on aluminium and its alloys - Measurement of total reflectance using a photoelectric reflectometer |
| BS 6161-14-1987 | 铝及铝合金阳极氧化镀层试验方法.第14部分:红外反射率测定 | Methods of test for anodic oxidation coatings on aluminium and its alloys - Determination of infra-red reflectance |
| BS 6161-18-1991 | 铝及铝合金阳极氧化镀层试验方法.第18部分:表面耐磨性测定 | Methods of test for anodic oxidation coatings on aluminium and its alloys - Determination of surface abrasion resistance |
| BS 6161-1993 | 铝及其合金的阳极氧化镀层的试验方法.第19部分:图象清晰度的测定.仪器测定法 | Methods of test for anodic oxidation coatings on aluminium and its alloys. Determination of image clarity. Instrumental method |
| BS 6161-7-1984 | 铝及其合金阳极氧化镀层试验方法.第7部分:阳极氧化有色镀层的人造光耐光度加速测定法 | Methods of test for anodic oxidation coatings on aluminium and its alloys - Accelerated determination of light fastness of coloured anodic oxidation coatings using artificial light |
| BS 6200-2.2-1993 | 铁、钢和其它黑色金属的抽样和分析.第2部分:抽样和样品制备.第2节:铁合金和其它合金添加剂抽样和样品制备方 | Sampling and analysis of iron, steel and other ferrous metals - Sampling and sample preparation - Methods for ferroalloys and other alloying additives |
| BS 6200-3.1.4-1990 | 铁、钢和其他黑色金属抽样和分析.第3部分:分析方法.第1节:铝含量测定.第4小节:非合金钢:火焰原子吸收分光光 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of aluminium - Non-alloyed steel: flame atomic absorption spectrometric method |
| BS 6200-3.1.5-1985 | 铁、钢和其他黑色金属抽样与分析.第3部分:分析方法.第1节:铝含量测定.第5小节:铁硅合金:原子吸收光谱法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of aluminium - Ferrosilicon: atomic absorption spectrometric method |
| BS 6200-3.1.6-1991 | 铁、钢和其他黑色金属抽样与分析.第3部分:分析方法.第1节:铝含量测定.第6小节:永磁合金:体积法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of aluminium - Permanent magnet alloys: volumetric method |
| BS 6200-3.10.4-1985 | 铁、钢和其他黑色金属抽样与分析.第3部分:分析方法.第10节:铬含量测定.第4小节:铁铬合金和铁硅铬合金:电位 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of chromium - Ferrochromium and ferrosilicochromium: potentiometric method |
| BS 6200-3.11.1-1991 | 铁、钢和其他铁合金的抽样和分析.分析方法.钴的测定.钢和铸铁:分光光度测定法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of cobalt - Steel and cast iron: spectrophotometric method |
| BS 6200-3.12.2-1985 | 铁、钢和其他铁合金的抽样和分析.分析方法.铜的测定.钢和铸铁:分光光度测定法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of copper - Steel and cast iron: spectrophotometric method |
| BS 6200-3.12.5-1986 | 铁、钢和其他铁金属的抽样和分析.分析方法.铜的测定.永磁合金:容量法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of copper - Permanent magnet alloys: volumetric method |
| BS 6200-3.16.1-1986 | 铁、钢和其他铁金属的抽样和分析.分析方法.铅的测定.碳钢和低合金钢:重量法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of lead - Carbon steels and low alloy steels: gravimetric method |
| BS 6200-3.18.2-1985 | 铁、钢和其他铁合金的抽样和分析.分析方法.锰的测定.钢:分光光度测定法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of manganese - Steel: spectrophotometric method |
| BS 6200-3.18.3-1985 | 铁、钢和其他铁合金的抽样和分析.分析方法.锰的测定.铁锰合金和硅锰铁合金:电位滴定法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of manganese - Ferromanganese and ferrosilicomanganese: potentiometric method |
| BS 6200-3.19.1-1985 | 铁、钢和其他铁合金的抽样和分析.分析方法.钼的测定.钢和铸铁:光度分析法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of molybdenum - Steel and cast iron: photometric method |
| BS 6200-3.20.3-1985 | 铁、钢和其他铁合金的抽样和分析.分析方法.镍的测定.钢和铸铁:分光光度测定法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of nickel - Steel and cast iron: spectrophotometric method |
| BS 6200-3.22.3-1986 | 铁、钢和其他铁合金的抽样和分析.分析方法.氮的测定.钢:分光光度测定法(痕量) | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of nitrogen - Steel: spectrophotometric method (for trace amounts) |
| BS 6200-3.26.5-1985 | 铁、钢和其他黑色金属抽样与分析.第3部分:分析方法.第26节:硅含量测定.第5小节:铁硅合金、铁硅锰合金和铁硅 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of silicon - Ferrosilicon, ferrosilicomanganese and ferrosilicochromium: gravimetric method |
| BS 6200-3.32.4-1985 | 铁、钢和其他黑色金属抽样与分析.第3部分:分析方法.第32节:钛含量测定.第4小节:铁钛合金:体积法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of titanium - Ferrotitanium: volumetric method |
| BS 6200-3.33.3-1985 | 铁、钢和其他黑色金属抽样与分析.第3部分:分析方法.第33节:钨含量测定.第3小节:铁钨合金:称重法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of tungsten - Ferrotungsten: gravimetric method |
| BS 6200-3.34.4-1985 | 铁、钢和其他铁合金的抽样和分析.分析方法.钒的测定.钒铁:电位滴定法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of vanadium - Ferrovanadium: potentiometric method |
| BS 6200-3.8.5-1991 | 铁、钢和其他铁合金的抽样和分析.分析方法.碳的测定.铸铁和生铁：非化合碳测定用重量方法 | Sampling and analysis of iron, steel and other ferrous metals - Methods of analysis - Determination of carbon - Cast iron and pig iron: gravimetric method for the determination of non-combined carbon |
| BS 643-1970 | 浇制钢丝绳端头用白色合金锭规范 | Specification for white metal ingots for capping steel wire ropes |
| BS 6480-1988 | 额定电压在33KV及以下的铅与铅合金护套浸渍纸绝缘的电缆规范 | Specification for impregnated paper-insulated lead or lead alloy sheathed electric cables of rated voltages up to and including 33000 V |
| BS 6496-1984 | 施加并焙固于铝合金的挤压材、板材和预成型材(外部建筑用)的粉末有机涂层和带有粉末有机涂层的铝合金挤压材 | Specification for powder organic coatings for application and stoving to aluminium alloy extrusions, sheet and preformed sections for external architectural purposes, and for the finish on aluminium alloy extrusions, sheet and preformed sections coated with powder organic coatings |
| BS 6582-2000 | 连续热浸铅合金(铅锡合金)镀层的冷轧扁平碳钢制品 | Continuously hot-dip lead alloy (terne) coated cold reduced carbon steel flat rolled products |
| BS 6615-1996 | 金属和金属合金铸件的尺寸公差规范 | Specification for dimensional tolerances for metal and metal alloy castings |
| BS 6669-1-1986 | 银和银合金电镀层的试验方法.第1部分:镀层厚度的测定 | Methods of test for electroplated silver and silver alloy coatings - Determination of coating thickness |
| BS 6669-2-1986 | 银和银合金电镀层的试验方法.第2部分:粘合力试验 | Methods of test for electroplated silver and silver alloy coatings - Adhesion tests |
| BS 6669-3-1989 | 银和银合金电镀层的试验方法.第3部分:残留盐的检测 | Methods of test for electroplated silver and silver alloy coatings - Detection of residual salts |
| BS 6670-1-1986 | 金和金合金电镀层的试验方法.第1部分:镀层厚度的测定 | Methods of test for electroplated gold and gold alloy coatings - Determination of coating thickness |
| BS 6670-4-1986 | 金和金合金电镀层的试验方法.第4部分:金含量的测定 | Methods of test for electroplated gold and gold alloy coatings - Determination of gold content |
| BS 6670-5-1986 | 金和金合金电镀层的试验方法.第5部分:粘合力试验 | Methods of test for electroplated gold and gold alloy coatings - Adhesion tests |
| BS 6675-1986 | 供水设备用供水阀门(铜合金)规范 | Specification for servicing valves (copper alloy) for water services |
| BS 6721-10-1989 | 铜和铜合金的取样与分析.第10部分:用滴定法对铜合金中铬的测定方法 | Sampling and analysis of copper and copper alloys - Method for determination of chromium in copper alloys: titrimetric method |
| BS 6721-11-1989 | 铜和铜合金的取样与分析.第11部分:用燃烧滴定法对铜和铜合金中硫的测定方法 | Sampling and analysis of copper and copper alloys - Method for determination of sulphur in copper and copper alloys: combustion titrimetric method |
| BS 6721-4-1986 | 铜和铜合金的取样与分析.第4部分:采用火焰原子吸收分光光度法对铜与铜合金中铬的测定方法 | Sampling and analysis of copper and copper alloys - Method for determination of chromium in copper and copper alloys by flame atomic absorption spectrophotometry |
| BS 6721-5-1986 | 铜和铜合金的取样与分析.第5部分:采用火焰原子吸收分光光度法对铜与铜合金中锌的测定方法 | Sampling and analysis of copper and copper alloys - Method for determination of zinc in copper and copper alloys by flame atomic absorption spectrophotometry |
| BS 6721-6-1989 | 铜和铜合金的取样与分析.第6部分:用分光光度法对铜和铜合金中磷的测定方法 | Sampling and analysis of copper and copper alloys - Method for determination of phosphorus in copper and copper alloys by spectrophotometry |
| BS 6721-7-1989 | 铜和铜合金的取样与分析.第7部分:用重力分析法对铜合金中镍的测定方法 | Sampling and analysis of copper and copper alloys - Method for determination of nickel in copper alloys: gravimetric method |
| BS 6721-8-1989 | 铜和铜合金的取样与分析.第8部分:用滴定法对铜合金中镍的测定方法 | Sampling and analysis of copper and copper alloys - Method for determination of nickel in copper alloys: titrimetric method |
| BS 6721-9-1989 | 铜和铜合金的取样与分析.第9部分:用火焰原子吸收分光光度法对铜合金中铅的测定方法 | Sampling and analysis of copper and copper alloys - Method for determination of lead in copper alloys by flame atomic absorption spectrophotometry |
| BS 6783-1-1986 | 镍、镍铁和镍合金的取样与分析.第1部分:采用火焰原子吸收光谱法对镍中银、铋、镉、钴、铜、铁、锰、铅和锌 | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for determination of silver, bismuth, cadmium, cobalt, copper , iron, manganese, lead and zinc in nickel by flame atomic absorption spectrometry |
| BS 6783-10-1990 | 镍、镍铁和镍合金的取样与分析.第10部分:镍合金中铁含量的测定方法(重铬酸钾滴定法) | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for determination of iron in nickel alloys (titrimetric method using potassium dichromate) |
| BS 6783-11-1990 | 镍、镍铁和镍合金的取样与分析.第11部分:镍合金钴含量的测定方法(六氰基高铁酸钠电位滴定法) | Sampling and analysis of nickel, ferronickel and nickel alloys. Method for the determination of cobalt in nickel alloys (potentiometric titration method using potassium hexacyanoferrate (III)) |
| BS 6783-12-1992 | 镍、镍铁和镍合金的取样与分析.第12部分:利用钼蓝分子吸收光谱测定法测定镍合金中磷的方法 | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for the determination of phosphorus in nickel alloys by molybdenum blue molecular absorption spectrometry |
| BS 6783-13-1992 | 镍、镍铁和镍合金的取样与分析.第13部分:用磷钒钼分子吸收光谱法对镍、镍铁和镍合金中磷的测定方法 | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for the determination of phosphorus in nickel, ferronickel and nickel alloys by phosphovanadomolybdate molecular absorption spectrometry |
| BS 6783-14-1994 | 镍、镍铁和镍合金取样和分析.采用姜黄分子吸收光谱法对镍和镍合金中硼总含量的测定方法. | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for the determination of total boron content of nickel, and nickel alloys by curcumin molecular absorption spectrometry |
| BS 6783-15-1994 | 镍.镍铁和镍合金的取样和分析.采用二安替比林基低甲烷分子吸收光谱法对镍合金中的钛合金含量的测定方法 | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for the determination of titanium in nickel alloys by diantipyrylmethane molecular absorption spectrometry |
| BS 6783-2-1986 | 镍、镍铁和镍的合金取样与分析.第2部分:镍铁中镍的测定方法(丁二酮酚重力分析法) | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for determination of nickel in ferronickel (dimethylglyoxime gravimetric method) |
| BS 6783-3-1986 | 镍、镍铁和镍合金的取样与分析.第3部分:采用火焰原子吸收光谱法镍铁中钴的测定方法 | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for determination of cobalt in ferronickel by flame atomic absorption spectrometry |
| BS 6783-4-1986 | 镍、镍铁和镍合金的取样与分析.第4部分:用电热原子吸收光谱测定法测定银、砷、铋、镉、铅、锑、硒、锡、碲 | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for determination of silver, arsenic, bismuth, cadmium, lead, antimony, selenium, tin, tellurium and thallium in nickel by electrothermal atomic absorption spectrometry |
| BS 6783-5-1986 | 镍、镍铁和镍合金的取样与分析.第5部分:感应电炉燃烧后用红外吸收法测定镍、镍铁和镍合金中碳的方法 | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for determination of carbon in nickel, ferronickel and nickel alloys by infra-red absorption after induction furnace combustion |
| BS 6783-6-1986 | 镍、镍铁和镍合金的取样与分析.第6部分:硫化氢产生后用甲蓝分子吸收光谱测定法测定镍中硫的方法 | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for determination of sulphur in nickel by methylene blue molecular absorption spectrometry after generation of hydrogen sulphide |
| BS 6783-7-1986 | 镍、镍铁和镍合金的取样与分析.第7部分:感应电炉燃烧后用红外测定镍镍铁和镍合金中硫的方法 | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for determination of sulphur in nickel, ferronickel and nickel alloys by infra-red absorption after induction furnace combustion |
| BS 6783-8-1986 | 镍、镍铁和镍合金的取样与分析.第8部分:感应电炉燃烧后用碘滴定法测定镍、镍铁和镍合金中硫的方法 | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for determination of sulphur in nickel, ferronickel and nickel alloys by iodimetric titration after induction furnace combustion |
| BS 6783-9-1986 | 镍、镍铁和镍合金的取样与分析.第9部分:镍铁中硅的测定方法(重力分析法) | Sampling and analysis of nickel, ferronickel and nickel alloys - Method for determination of silicon in ferronickel (gravimetric method) |
| BS 6878-1988 | 工业用高压开关设备和控制装置规范.充气式高压开关设备和控制装置用铸铝合金外壳 | Specification for high-voltage switchgear and controlgear for industrial use - Cast aluminium alloy enclosures for gas-filled high-voltage switchgear and controlgear |
| BS 6931-1988 | 铜和铜合金的术语词汇 | Glossary of terms for copper and copper alloys |
| BS 6SP 4-2000 | 强度级别为880/1080MPa的带头平杆钻头式钢合金和耐腐蚀钢制销钉 | Pins headed, plain shank, drilled, steel alloy and corrosion resisting steel with a strength class 880 / 1080 MPa |
| BS 7252-10-1997 | 外科植物入用金属材料.第10部分:煅制钛5-铝2.5-铁合金规范 | Metallic materials for surgical implants - Specification for wrought titanium 5-aluminium 2,5-iron alloy |
| BS 7252-11-1995 | 外科植入物用金属材料.第11部分:可锻钛6-铝7-铌合金规范 | Metallic materials for surgical implants - Specification for wrought titanium 6-aluminium 7-niobium alloy |
| BS 7252-12-1997 | 外科植物入用金属材料.第12部分:煅制钴-铬-钼合金规范 | Metallic materials for surgical implants - Specification for wrought cobalt-chromium-molybdenum alloy |
| BS 7252-13-1997 | 外科植入物用金属材料.外科植入用非合金钽规范 | Metallic materials for surgical implants - Specification for unalloyed tantalum for surgical implant applications |
| BS 7252-3-1997 | 外科植入物用金属材料.锻制钛6-铝4-钒合金规范 | Metallic materials for surgical implants - Specification for wrought titanium 6-aluminium 4-vanadium alloy |
| BS 7252-4-1997 | 外科植入物用金属材料.第4部分:钴-铬-钼铸造合金规范 | Metallic materials for surgical implants - Specification for cobalt-chromium-molybdenum casting alloy |
| BS 7252-5-1994 | 外科植入物用金属材料.第5部分:可锻钴-铬-钨-镍合金规范 | Metallic materials for surgical implants - Specification for wrought cobalt-chromium-tungsten-nickel alloy |
| BS 7252-6-1997 | 外科植入物用金属材料.可锻钴-镍-铬-钼合金规范 | Metallic materials for surgical implants - Specification for wrought cobalt-nickel-chromium-molybdenum alloy |
| BS 7252-7-1994 | 外科植入物用金属材料.第7部分:钴-铬-镍-钼-铁合金规范 | Metallic materials for surgical implants - Specification for cobalt-chromium-nickel-molybdenum-iron alloy |
| BS 7252-8-1997 | 外科植入物用金属材料.可锻钴-镍-铬-钼-钨-铁合金规范 | Metallic materials for surgical implants - Specification for wrought cobalt-nickel-chromium-molybdenum-tungsten-iron alloy |
| BS 7254-5-1990 | 矫形外科植入物.第5部分:钴-铬-钼合金制铸件的生产规范 | Orthopaedic implants - Specification for production of castings made of cobalt-chromium-molybdenum alloy |
| BS 7315-1990 | 充气高压开关设备和控制装置用锻铝和铝合金壳体规范 | Specification for wrought aluminium and aluminium alloy enclosures for gas-filled high-voltage switchgear and controlgear |
| BS 7438-1991 | 弹簧加载型钢和铜合金单盘压片止回阀规范 | Specification for steel and copper alloy wafer check valves, single-disk, spring-loaded type |
| BS 7455-1-1991 | 采用火焰原子吸收光谱法对镍合金的分析.一般要求和样件溶解 | Analysis of nickel alloys by flame atomic absorption spectrometry - General requirements and sample dissolution |
| BS 7455-2-1991 | 采用火焰原子吸收光谱测定法对镍合金的分析.钴的测定方法 | Analysis of nickel alloys by flame atomic absorption spectrometry - Method for the determination of cobalt |
| BS 7455-3-1991 | 采用火焰原子吸收光谱测定法对镍合金的分析.铬的测定方法 | Analysis of nickel alloys by flame atomic absorption spectrometry - Method for the determination of chromium |
| BS 7455-4-1991 | 采用火焰原子吸收光谱测定法对镍合金的分析.铜的测定方法 | Analysis of nickel alloys by flame atomic absorption spectrometry - Method for the determination of copper |
| BS 7455-5-1991 | 采用火焰原子吸收光谱测定法对镍合金的分析.铁的测定方法 | Analysis of nickel alloys by flame atomic absorption spectrometry - Method for the determination of iron |
| BS 7455-6-1991 | 采用火焰原子吸收光谱测定法对镍合金的分析.锰的测定方法 | Analysis of nickel alloys by flame atomic absorption spectrometry - Method for the determination of manganese |
| BS 7455-7-1992 | 用火焰原子吸收光谱测定法对镍合金的分析.第7部分:铝含量的测定方法 | Analysis of nickel alloys by flame atomic absorption spectrometry - Method for determination of aluminium |
| BS 7455-8-1992 | 采用火焰原子吸收光谱法对镍合金的分析.第8部分:硅的测定方法 | Analysis of nickel alloys by flame atomic absorption spectrometry - Method for determination of silicon |
| BS 7455-9-1994 | 采用火焰原子吸收光谱法对镍合金的分析.第9部分:钒含量的测定方法 | Analysis of nickel alloys by flame atomic absorption spectrometry - Method for determination of vanadium |
| BS 7545-1991 | 从金属和合金腐蚀试样去除腐蚀制品的方法 | Method for removal of corrosion products from corrosion test specimens of metals and alloys |
| BS 7745-1-1994 | 带有铜焊螺旋形硬质合金尖的端铣刀.直柄端铣刀尺寸 | End mills with brazed helical hardmetal tips - Dimensions of end mills with parallel shank |
| BS 7745-2-1994 | 带有铜焊螺旋形硬质合金尖的端铣刀.锥柄端铣刀尺寸 | End mills with brazed helical hardmetal tips - Dimensions of end mills with taper shank |
| BS 7839-1995 | 直柄实心硬质合金端铣刀.尺寸 | Solid hardmetal end-mills with parallel shanks - Dimensions |
| BS 7L 37-1989 | 铝-铜-镁-硅-锰合金的整体冷锻制铆钉用金属线规范(用于溶解处理和自然老化状态)(直径不超过10mm)(铜4.4、镁 | Specification for wire for solid cold-forged rivets of aluminium-copper-magnesium-silicon-manganese alloy (for use in the solution treated and naturally aged condition) (not exceeding 10 mm diameter) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) (2014A) |
| BS 864-3-1975 | 铜和铜合金制毛细管与承压管管件.第3部分:聚乙烯管用承压管件 | Capillary and compression tube fittings of copper and copper alloy - Compression fittings for polyethylene pipes |
| BS A 254, A 255 [...]-1976 | 规范.六角头钛合金螺栓160 000 lbf/inUP2 (1100 MPa) | Specification - Hexagonal head titanium alloy bolts 160 000 lbf/inUP2 (1100 MPa) |
| BS A 254, A 255, A 256, A 257, A 258, A 259-1976 | 规范.六角头钛合金螺栓160 000 磅力/英寸(上标2)(1100MPa) | Specification - Hexagonal head titanium alloy bolts 160 000 lbf/inUP2 (1100 MPa) |
| BS A 254-1976 | 160,000磅力/平方英寸(1100MPa)六角头钛合金螺栓规范 | Specification - Hexagonal head titanium alloy bolts 160 000 lbf/in2 (1100 MPa) |
| BS A 266, A 267 [...]-1977 | 带高转距速度驱动凹槽的100 沉头钛合金螺栓160 000 lbf/inUP2 (1100 MPa)规范 | Specification for 100 ° countersunk head titanium alloy bolts 160 000 lbf/inUP2 (1100 MPa) with Hi-torque speed drive recesses |
| BS A 266, A 267, A 268, A 269, A 270, A 271-1977 | 有高转矩快速旋入凹槽的160000lbf/in<上标2>(1100MPa)的100°埋头钛合金螺栓规范 | Specification for 100 ° countersunk head titanium alloy bolts 160 000 lbf/inUP2 (1100 MPa) with Hi-torque speed drive recesses |
| BS A 266-1977 | 具有高扭矩速度引导槽的抗拉强度为160,000磅力/平方英寸(1100MPa)的100°沉头钛合金螺栓规范 | Specification for 100 ° countersunk head titanium alloy bolts 160 000 lbf/in2 (1100 MPa) with Hi-torque speed drive recesses |
| BS A 299-1989 | 抗拉强度为1250MPa和具有MJ螺纹的合金钢凸头螺栓采办规范 | Specification for procurement of alloy steel protruding head bolts with strength classification 1 250 MPa and MJ threads |
| BS A 300-1989 | 抗拉强度为1100MPa和具有MJ螺纹的合金钢螺栓采办规范 | Specification for procurement of alloy steel bolts with strength classification 1 100 MPa and MJ threads |
| BS A 332-1999 | 航空航天用1100MPa强度的MJ螺纹钛合金螺栓.采购规范 | Aerospace - Bolts, with MJ threads, in titanium alloys, strength class 1 100 MPa - Procurement specification |
| BS A 351-2000 | 镍合金实心铆钉.采购规范 | Rivets, solid, in nickel alloy - Procurement specification |
| BS A 352-2000 | 钛或钛合金的实心铆钉.采购规范 | Rivets, solid, in titanium or titanium alloy - Procurement specification |
| BS A 363-2000 | 强度等级为1550MPa耐热镍基合金MJ螺纹螺栓.采购规范 | Bolts, with MJ threads, made of heat-resistant nickel-based alloy, strength class 1 550 MPa - Procurement specification |
| BS AU 50-2.5c-1996 | 轮胎和车轮.车轮和轮辋.乘用车全部用或部分用轻铸合金制造的道路车轮规范 | Tyres and wheels - Wheels and rims - Specification for road wheels manufactured wholly or partly of cast light alloy for passenger cars |
| BS AU 50-2.6a-1983 | 轮胎和车轮.第2部分:车轮和轮辋.第6节:机动自行车和摩托车全部用或部分用轻质合金制造的道路车轮规范 | Tyres and wheels - Wheels and rims - Specification for road wheels manufactured wholly or partly of light alloy for mopeds and motor cycles |
| BS B 100-1992 | 锻造铜合金的检测,试验和验收程序 | Procedure for inspection, testing and acceptance of wrought copper alloys |
| BS B 23-1991 | 铜-铝-镍-铁合金棒材、型材、锻坯和锻件规范 | Specification for copper-aluminium-nickel-iron alloy rods, sections, forging stock and forgings |
| BS B 24-1991 | 铜-锡-磷合金棒材和型材规范 | Specification for copper-tin-phosphorous alloy rods and sections |
| BS DD 139-1986 | 锌铝合金铸锭和铸件规范 | Specification for zinc-aluminium alloy ingots and castings |
| BS DD CEN/TS 13547-2007 | 工业阀门.铜合金球阀 | Industrial valves - Copper alloy ball valves |
| BS DD CEN/TS 14938-2-2006 | 铜和铜合金.测定铋含量.火焰原子吸收光谱测定法(FAAS) | Copper and copper alloys - Determination of bismuth content - FAAS method |
| BS DD CEN/TS 15022-4-2007 | 铜和铜合金.测定锡含量.介质锡含量.火焰原子吸收光谱测定法(FAAS) | Copper and copper alloys - Determination of tin content - Medium tin content - Flame atomic absorption spectrometry method (FAAS) |
| BS DD CEN/TS 15023-3-2007 | 铜和铜合金.测定镍含量.火焰原子吸收光谱测定法(FAAS) | Copper and copper alloys - Determination of nickel content - Flame atomic absorption spectrometry method (FAAS) |
| BS DD CEN/TS 15025-2007 | 铜和铜合金.测定镁含量.火焰原子吸收光谱测定法(FAAS) | Copper and copper alloys - Determination of magnesium content - Flame atomic absorption spectrometry method (FAAS) |
| BS DD CEN/TS 15476-2006 | 肥料.用氏合金还原蒸馏法测定氮和氨态氮 | Fertilizers - Determination of nitric and ammoniacal nitrogen according to Devarda |
| BS DD ENV 12908-1998 | 铅和铅合金.火花激发光学发射光谱测定法分析 | Lead and lead alloys - Analysis by optical emission spectrometry (OES) with spark excitation |
| BS DD ENV 13800-2000 | 铅及铅合金.无铅基质分离的火焰原子吸收光谱分析法(FAAS)或感应耦合等离子体发射光谱分析法(ICP-ES) | Lead and lead alloys - Analysis by flame atomic absorption spectromerty (FAAS) or inductively coupled plasma emission spectrometry (ICP-ES), without separation of the lead matrix |
| BS DD ENV 14029-2001 | 铅及铅合金.铅矩阵分离后的火焰原子吸收光谱法(FAAS)或感应耦合等离子体发射光谱法(ICP-ES)分析 | Lead and lead alloys - Analysis by flame atomic absorption spectrometry (FAAS) or inductively coupled plasma emission spectrometry (ICP-ES), after separation of the lead matrix |
| BS DD ENV 14138-2001 | 铅及铅合金.共沉淀法分离后用火焰原子吸收光谱法(FAAS)或感应耦合等离子体发射光谱法(ICP-ES)进行分析 | Lead and lead alloys - Analysis by flame atomic absorption spectrometry (FAAS) or inductively coupled plasma emissions spectrometry (ICP-ES), after separation by co-precipitation |
| BS DD IEC/PAS 62483-2007 | 测量锡和锡合金表面抛光的须晶生长用试验方法 | Test method for measuring whisker growth on tin and tin alloy surface finishes |
| BS DD ISO/TS 13899-3-2006 | 钢.合金钢中钼、铌和钨含量的测定.感应耦合等离子体原子发射光谱法.钨含量的测定 | Steel - Determination of Mo, Nb and W contents in alloyed steel - Inductively coupled plasma atomic emission spectrometric method - Determination of W content |
| BS DD ISO/TS 17576-2007 | 牙科学.汞齐合金的腐蚀试验 | Dentistry - Corrosion tests for amalgam |
| BS EN 10016-1-1995 | 拉制和/或冷轧用非合金钢棒.一般要求 | Non-alloy steel rods for drawing and/or cold rolling - General requirements |
| BS EN 10016-2-1995 | 拉制和/或冷轧用的非合金钢棒.一般用途钢棒的特定要求 | Non-alloy steel rods for drawing and/or cold rolling - Specific requirements for general purpose rod |
| BS EN 10016-3-1995 | 拉制和/或冷轧用的非合金钢棒.沸腾和沸腾代用低碳钢棒的特殊要求 | Non-alloy steel rods for drawing and/or cold rolling - Specific requirements for rimmed and rimmed substitute low carbon steel rod |
| BS EN 10016-4-1995 | 拉制和/或冷轧用非合金钢棒材.专用棒材的特殊要求 | Non-alloy steel rods for drawing and/or cold rolling - Specific requirements for rod for special applications |
| BS EN 10025-1-2004 | 非合金结构钢.一般交货技术条件 | Hot rolled products of structural steels - General technical delivery conditions |
| BS EN 10025-2-2004 | 非合金结构钢.非合金结构钢的交货技术条件 | Hot rolled products of structural steels - Technical delivery conditions for non-alloy structural steels |
| BS EN 10028-2-2003 | 挤压用钢制扁平制品.带规定高温特性的非合金钢和合金钢 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| BS EN 10028-4-2003 | 挤压用钢制扁平制品.带规定低温特性的镍合金钢 | Flat products made of steels for pressure purposes - Nickel alloy steels with specified low temperature properties |
| BS EN 10051-1992 | 非合金钢和合金钢连续热轧的未涂覆板材、薄板材和带材规范.尺寸和形状公差 | Specification for continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels - Tolerances on dimensions and shape |
| BS EN 10083-2-2006 | 淬硬钢和回火钢.非合金钢的交货技术条件 | Steels for quenching and tempering - Technical delivery conditions for non alloy steels |
| BS EN 10083-3-2006 | 淬硬钢和回火钢.合金钢的交货技术条件 | Steels for quenching and tempering - Technical delivery conditions for alloy steels |
| BS EN 10090-1998 | 内燃机用阀门钢和合金 | Valve steels and alloys for internal combustion engines |
| BS EN 10095-1999 | 耐热钢和镍合金 | Heat resisting steels and nickel alloys |
| BS EN 1011-4-2000 | 焊接.金属材料焊接的推荐规范.铝及铝合金的电弧焊接 | Welding - Recommendations for welding of metallic materials - Arc welding of aluminium and aluminium alloys |
| BS EN 10184-2006 | 黑色金属材料化学分析.非合金钢铁中磷的测定.钼蓝光度法测定酸溶硅量 | Chemical analysis of ferrous materials - Determination of phosphorus in non-alloyed steels and irons - Molybdenum blue spectrophotometric method |
| BS EN 10210-1-2006 | 非合金和细晶结构钢的热精加工空心型材.交货技术要求 | Hot finished structural hollow sections of non-alloy and fine grain steels - Technical delivery requirements |
| BS EN 10210-2-2006 | 细晶结构钢和非合金热轧空心型材.公差、尺寸和截面特性 | Hot finished structural hollow sections of non-alloy and fine grain steels - Tolerances, dimensions and sectional properties |
| BS EN 10216-1-2002 | 承压用的无缝钢管.交付技术状态.规定了室温特性的非合金钢管 | Seamless steel tubes for pressure purposes - Technical delivery conditions |
| BS EN 10216-2-2002 | 承压用的无缝钢管.交付技术状态.规定了高温特性的非合金和合金钢管 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Non-alloy and alloy steel tubes with specified elevated temperature properties |
| BS EN 10216-3-2002 | 承压用的无缝钢管.交付技术状态.合金细晶粒钢管 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Alloy fine grain steel tubes |
| BS EN 10216-4-2002 | 承压用的无缝钢管.交付技术状态.规定了低温特性的非合金和合金钢管 | Seamless steel tubes for pressure purposes - Technical delivery conditions |
| BS EN 10217-1-2002 | 承压用焊接钢管.交付技术状态.规定室温特性的非合金钢管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Non-alloy steel tubes with specified room temperature properties |
| BS EN 10217-2-2002 | 承压用的焊接钢管.交付技术状态.规定了高温特性的非合金和合金电焊钢管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties |
| BS EN 10217-3-2002 | 承压用的焊接钢管.交付技术状态.合金细晶粒钢管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Alloy fine grain steel tubes |
| BS EN 10217-4-2002 | 承压用的焊接钢管.交付技术状态.规定了低温特性的非合金和合金电焊钢管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Electric welded non-alloy steel tubes with specified low temperature properties |
| BS EN 10217-5-2002 | 承压用的焊接钢管.交付技术状态.规定了高温特性的非合金和合金埋弧焊接钢管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties |
| BS EN 10217-6-2002 | 承压用的焊接钢管.交付技术条件.规定了低温特性的非合金埋弧焊接钢管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Submerged arc welded non-alloy steel tubes with specified low temperature properties |
| BS EN 10219-1-2006 | 非合金和细晶结构钢的冷成形焊接结构空心型材.交货技术要求 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Technical delivery requirements |
| BS EN 10219-2-2006 | 非合金和细晶结构钢的冷成形焊接结构空心型材.公差、尺寸和局部特性 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Tolerances, dimensions and sectional properties |
| BS EN 10223-1-1998 | 栏栅用钢丝和金属丝制品.锌和锌合金包覆的刺钢丝 | Steel wire and wire products for fences - Zinc and zinc alloy coated steel barbed wire |
| BS EN 10224-2002 | 包括生活用水在内的含水液的输送用非合金钢管和配件.交货技术条件 | Non-alloy steel tubes and fittings for the conveyance of water and other aqueous liquids - Technical delivery conditions |
| BS EN 10244-2-2001 | 钢丝及其制品.钢丝上的非有色金属涂层.锌和锌合金涂层 | Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Zinc or zinc alloy coatings |
| BS EN 10248-1-1996 | 非合金钢热轧制板桩.第1部分:交付技术状态 | Hot rolled sheet piling of non alloy steels - Technical delivery conditions |
| BS EN 10248-2-1996 | 非合金钢热轧板桩.第2部分 形状和尺寸公差 | Hot rolled sheet piling of non alloy steels - Tolerances on shape and dimensions |
| BS EN 10249-1-1996 | 非合金钢冷成型板桩.第1部分:交付技术状态 | Cold formed sheet piling of non alloy steels - Technical delivery conditions |
| BS EN 10249-2-1996 | 非合金钢冷成型板桩.第2部分:形状和尺寸公差 | Cold formed sheet piling of non alloy steels - Tolerances on shape and dimensions |
| BS EN 10250-2-2000 | 一般工程用敞口钢模锻件.非合金质量特种钢 | Open steel die forgings for general engineering purposes - Non-alloy quality and special steels |
| BS EN 10250-3-2000 | 一般工程用敞口钢模锻件.合金特种钢 | Open steel die forgings for general engineering purposes - Alloy special steels |
| BS EN 10255-2004 | 焊接或加螺纹的非合金钢管.交货技术条件 | Non-alloy steel tubes suitable for welding and threading - Technical delivery conditions |
| BS EN 10257-1-1998 | 电力电缆或通信电缆铠装用镀锌或锌合金非合金钢丝.地面电缆 | Zinc or zinc alloy coated non-alloy steel wire for armouring either power cables or telecommunication cables - Land cables |
| BS EN 10257-2-1998 | 电力电缆或通信电缆铠装用锌或锌合金涂覆非合金钢丝.海底电缆 | Zinc or zinc alloy coated non-alloy steel wire for armouring either power cables or telecommunication cables - Submarine cables |
| BS EN 10264-2-2002 | 钢丝和钢丝产品.绳索用钢丝.一般绳索用的冷拉非合金钢丝 | Steel wire and wire products - Steel wire for ropes - Cold drawn non alloy steel wire for ropes for general applications |
| BS EN 10264-3-2002 | 钢丝和钢丝产品.绳索用钢丝.重型装置用圆形和异型非合金钢丝 | Steel wire and wire products - Steel wire for ropes - Round and shaped non alloyed steel wire for high duty applications |
| BS EN 10269-1999 | 规定高温和/或低温性能的紧固件用钢及镍合金 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| BS EN 10270-1-2001 | 金属弹簧用钢丝.获得专利的冷拉伸非合金弹簧钢丝 | Steel wire for mechanical springs - Patented cold drawn unalloyed spring steel wire |
| BS EN 10294-1-2005 | 机制空心棒.技术交货条件.非合金和合金钢 | Hollow bars for machining - Technical delivery conditions - Non alloy and alloy steels |
| BS EN 10296-1-2003 | 机械和一般工程用焊接圆钢管.技术交货条件.非合金和合金钢管 | Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Non-alloy and alloy steel tubes |
| BS EN 10297-1-2003 | 机械和普通工程用无缝圆形钢管.技术交货条件.非合金和合金钢管 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Non-alloy and alloy steel tubes |
| BS EN 10302-2002 | 耐蠕变的钢，镍和钴合金 | Creep resisting steels, nickel and cobalt alloys |
| BS EN 10335-2005 | 包装用钢.与人和动物消费用食品、产品或饮料接触的扁平钢制品.非合金电解铬/氧化铬镀钢 | Steel for packaging - Flat steel products intended for use in contact with foodstuffs, products or beverages for human and animal consumption - Non alloyed electrolytic chromium/chromium oxide coated steel |
| BS EN 10341-2006 | 以半成品状态交付的冷轧电气非合金和合金钢薄板材和带材 | Cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state |
| BS EN 1057-2006 | 铜和铜合金制品.卫生设备和水加热器的水和气体用无缝圆铜管 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| BS EN 1092-3-2004 | 法兰及其连接件.标注PN的管道、阀门、配件和附件用圆形法兰.铜合金法兰 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Copper alloy flanges |
| BS EN 1092-4-2002 | 法兰及其连接件.按PN标注的管道、阀门、配件和附件用圆形法兰.铝合金法兰 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Aluminium alloy flanges |
| BS EN 1172-1997 | 铜和铜合金.建筑用薄板和带材 | Copper and copper alloys - Sheet and strip for building purposes |
| BS EN 1173-1996 | 铜和铜合金.材料状态或回火符号 | Copper and copper alloys - Material condition or temper designation |
| BS EN 1179-2003 | 锌和锌合金.初级锌 | Zinc and zinc alloys - Primary zinc |
| BS EN 12020-1-2001 | 铝及铝合金.挤制合金EN AW-6060 和 EN AW-6063精密型材.检验和交付技术条件 | Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063: Technical conditions for inspection and delivery |
| BS EN 12020-2-2001 | 铝及铝合金.挤制合金EN AW-6060 和 EN AW-6063精密型材.尺寸和形状公差 | Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063: Tolerances on dimensions and form |
| BS EN 12060-1998 | 锌和锌合金.取样方法.规范 | Zinc and zinc alloys - Method of sampling - Specifications |
| BS EN 1213-2000 | 建筑物阀门.建筑物内饮水供水用的铜合金断流阀.试验和要求 | Building valves - Copper alloy stopvalves for potable water supply in buildings - Tests and requirements |
| BS EN 12163-1998 | 铜和铜合金.普通棒材 | Copper and copper alloys - Rod for general purposes |
| BS EN 12164-1998 | 铜及铜合金.快削加工用杆材 | Copper and copper alloys - Rod for free machining purposes |
| BS EN 12165-1998 | 铜和铜合金.已加工和未加工锻坯 | Copper and copper alloys - Wrought and unwrought forging stock |
| BS EN 12166-1998 | 铜及铜合金.普通线材 | Copper and copper alloys - Wire for general purposes |
| BS EN 12167-1998 | 铜及铜合金.通用型材和扁棒材 | Copper and copper alloys - Profiles and rectangular bar for general purposes |
| BS EN 12168-1998 | 铜和铜合金.切削加工用空心棒 | Copper and copper alloys - Hollow rod for free machining purposes |
| BS EN 12206-1-2004 | 颜料和清漆.建筑用铝和铝合金涂层.涂覆粉末制涂层 | Paints and varnishes - Coating of aluminium and aluminium alloys for architectural purposes - Coatings prepared from coating powder |
| BS EN 12258-1-1998 | 铝和铝合金.术语和定义.通用术语 | Aluminium and aluminium alloys - Terms and definitions - General terms |
| BS EN 12258-2-2004 | 铝和铝合金.术语和定义.化学分析 | Aluminium and aluminium alloys - Terms and definitions - Chemical analysis |
| BS EN 12258-3-2003 | 铝和铝合金.术语和定义.废料 | Aluminium and aluminium alloys - Terms and definitions - Scrap |
| BS EN 12258-4-2004 | 铝和铝合金.术语和定义.铝工业残留物 | Aluminium and aluminium alloys - Terms and definitions - Residues of the aluminium industry |
| BS EN 12288-2003 | 工业用阀.铜合金闸阀 | Industrial valves - Copper alloy gate valves |
| BS EN 12373-1-2001 | 铝及铝合金.阳极氧化.规定铝装饰和保护用阳极氧化覆层的方法 | Aluminium and aluminium alloys - Anodizing - Method for specifying decorative and protective anodic oxidation coatings on aluminium |
| BS EN 12373-10-1999 | 铝和铝合金.阳极氧化.使用磨损射流设备测定阳极氧化镀涂层主要特殊磨损抗性 | Aluminium and aluminium alloys - Anodizing - Measurement of mean specific abrasion resistance of anodic oxidation coatings using an abrasive jet test apparatus |
| BS EN 12373-11-2001 | 铝和铝合金.阳极氧化.20°、45°、60°和85°角的阳极氧化覆层的镜面反射系数和镜面光泽度的测量 | Aluminium and aluminium alloys - Anodizing - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 °, 45 °, 60 °, and 85 ° |
| BS EN 12373-12-2001 | 铝和铝合金.阳极氧化.用集成球形仪器测量铝表面反射特性 | Aluminium and aluminium alloys - Anodizing - Measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments |
| BS EN 12373-13-2001 | 铝和铝合金.阳极氧化.用角度光度计或滤色角度光度计测量铝表面反射特性 | Aluminium and aluminium alloys - Anodizing - Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer |
| BS EN 12373-14-2001 | 铝和铝合金.阳极氧化.阳极氧化层镜相清析的目视测定.表格刻度法 | Aluminium and aluminium alloys - Anodizing - Visual determination of image clarity of anodic oxidation coatings - Chart scale method |
| BS EN 12373-15-2001 | 铝和铝合金.阳极氧化.检查变形评估阳极氧化层耐裂性 | Aluminium and aluminium alloys - Anodizing - Assessment of resistance of anodic oxidation coatings to cracking by deformation |
| BS EN 12373-16-2001 | 铝及铝合金.阳极氧化.阳极氧化薄覆层连续性检查.硫酸铜试验 | Aluminium and aluminium alloys - Anodizing - Check for continuity of thin anodic oxidation coatings - Copper sulfate test |
| BS EN 12373-17-2001 | 铝及铝合金.阳极化.电介质击穿潜在性的测定 | Aluminium and aluminium alloys - Anodizing - Determination of electric breakdown potential |
| BS EN 12373-18-2001 | 铝及铝合金.阳极氧化.斑蚀评定的等级系统.图表法 | Aluminium and aluminium alloys - Anodizing - Rating system for the evaluation of pitting corrosion - Chart method |
| BS EN 12373-19-2001 | 铝及铝合金.阳极氧化.斑蚀评定的等级系统.坐标法 | Aluminium and aluminium alloys - Anodizing - Rating system for the evaluation of pitting corrosion - Grid method |
| BS EN 12373-2-1999 | 铝和铝合金.阳极氧化.阳极氧化涂层单位面积(表面密度)质量的测定.重量剂法 | Aluminium and aluminium alloys - Anodizing - Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetric method |
| BS EN 12373-3-1999 | 铝和铝合金.阳极氧化.阳极氧化涂层单位面积(表面密度)质量的测定.分束显微镜无损测量 | Aluminium and aluminium alloys - Anodizing - Determination of thickness of anodic oxidation coatings - Non-destructive measurement by split-beam microscope |
| BS EN 12373-4-1999 | 铝和铝合金.阳极氧化.预先酸处理的染料污点密封试验的阳极氧镀层吸收强度损失评估 | Aluminium and aluminium alloys - Anodizing - Estimation of loss of absorptive power of anodic oxidation coatings after sealing by dye spot test with prior acid treatment |
| BS EN 12373-5-1999 | 铝和铝合金.阳极氧化.通过导纳测量评估密封阳极氧化物镀层质量 | Aluminium and aluminium alloys - Anodizing - Assessment of quality of sealed anodic oxidation coatings by measurement of admittance |
| BS EN 12373-6-1999 | 铝和铝合金.阳极氧化.测定未预先酸处理的浸入磷酸/铬酸溶液后质量损失以评估密封阳极氧化镀层质量 | Aluminium and aluminium alloys - Anodizing - Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution without prior acid treatment |
| BS EN 12373-7-1999 | 铝和铝合金.阳极氧化.测定预先酸处理的浸入磷酸/铬酸溶液后质量损失评估密封阳极氧化镀层质量 | Aluminium and aluminium alloys - Anodizing - Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment |
| BS EN 12373-8-1999 | 铝和铝合金.阳极氧化.有色阳极氧化镀层对紫外光和热的比较牢固度测定 | Aluminium and aluminium alloys - Anodizing - Determination of the comparative fastness to ultra-violet light and heat of coloured anodic oxidation coatings |
| BS EN 12373-9-1999 | 铝和铝合金.阳极氧化.使用磨损轮磨损试验设备测定阳极氧化镀层磨损指数和磨损抗性 | Aluminium and aluminium alloys - Anodizing - Measurement of wear resistance and wear index of anodic oxidation coatings using an abrasive wheel wear test apparatus |
| BS EN 12384-1999 | 铜和铜合金.带材弹性弯曲极限值测定 | Copper and copper alloys - Determination of spring bending limit on strip |
| BS EN 12392-2000 | 铝和铝合金.锻压产品.生产压力设备用产品专门要求 | Aluminium and aluminium alloys - Wrought products - Special requirements for products intended for the production of pressure equipment |
| BS EN 12402-1999 | 铅和铅合金.分析用取样方法 | Lead and lead alloys - Methods of sampling for analysis |
| BS EN 12420-1999 | 铜和铜合金.锻件 | Copper and copper alloys - Forgings |
| BS EN 12421-1998 | 镁及镁合金.非合金镁 | Magnesium and magnesium alloys - Unalloyed magnesium |
| BS EN 12438-1998 | 镁及镁合金.铸造阳极用镁合金 | Magnesium and magnesium alloys - Magnesium alloys for cast anodes |
| BS EN 12441-1-2002 | 锌及锌合金.化学分析.锌合金中铝的测定.滴定法 | Zinc and zinc alloys - Chemical analysis - Determination of aluminium in zinc alloys - Titrimetric method |
| BS EN 12441-10-2005 | 锌和锌合金.化学分析.锌合金中铬和钛的测定.分光光度法 | Zinc and zinc alloys - Chemical analysis - Determination of chromium and titanium in zinc alloys - Spectrophotometric method |
| BS EN 12441-11-2006 | 锌和锌合金.化学分析.锌合金中硅的测定.分光光度法 | Zinc and zinc alloys - Chemical analysis - Determination of silicon in zinc alloys - Spectrophotometric method |
| BS EN 12441-2-2002 | 锌及锌合金.化学分析.锌合金中镁的测定.火焰原子吸收光谱法 | Zinc and zinc alloys - Chemical analysis - Determination of magnesium in zinc alloys - Flame atomic absorption spectrometric method |
| BS EN 12441-3-2002 | 锌及锌合金.化学分析.铅、镉、铜的测定.火焰原子吸收光谱法 | Zinc and zinc alloys - Chemical analysis - Determination of lead, cadmium and copper - Flame atomic absorption spectometric method |
| BS EN 12441-4-2003 | 锌和锌合金.化学分析.锌合金中铁含量的测定.分光光度法 | Zinc and zinc alloys - Chemical analysis - Determination of iron in zinc alloys - Spectrophotometric method |
| BS EN 12441-5-2003 | 锌和锌合金.化学分析.生锌中铁含量的测定.分光光度法 | Zinc and zinc alloys - Chemical analysis - Determination of iron in primary zinc - Spectrophotometric method |
| BS EN 12441-6-2003 | 锌和锌合金.化学分析.铝及铁含量的测定.火焰原子吸收光谱测定法 | Zinc and zinc alloys - Chemical analysis - Determination of aluminium and iron - Flame atomic absorption spectrometric method |
| BS EN 12441-7-2005 | 锌和锌合金.化学分析.锡的测定.萃取后的火焰原子吸收光谱测定法 | Zinc and zinc alloys - Chemical analysis - Determination of tin - Flame atomic absorption spectrometric method after extraction |
| BS EN 12441-8-2005 | 锌和锌合金.化学分析.二级锌中锡的测定.火焰原子吸收光谱测定法 | Zinc and zinc alloys - Chemical analysis - Detection of tin in secondary zinc - Flame atomic absorption spectrometric method |
| BS EN 12441-9-2005 | 锌和锌合金.化学分析.锌合金中镍的测定.火焰原子吸收光谱测定法 | Zinc and zinc alloys - Chemical analysis - Determination of nickel in zinc alloys - Flame atomic absorption spectrometric method |
| BS EN 12449-1999 | 铜和铜合金.普通无缝圆管 | Copper and copper alloys - Seamless, round tubes for general purposes |
| BS EN 12450-1999 | 铜和铜合金.圆铜无缝毛细管 | Copper and copper alloys - Seamless, round copper capillary tubes |
| BS EN 12451-1999 | 铜和铜合金.热交换器用圆无缝管 | Copper and copper alloys - Seamless, round tubes for heat exchangers |
| BS EN 12452-1999 | 铜和铜合金.热交换器用轧制翅片无缝管 | Copper and copper alloys - Rolled, finned, seamless tubes for heat exchangers |
| BS EN 12482-1-1998 | 铝和铝合金.通用重轧胚料.热轧重轧胚料规范. | Aluminium and aluminium alloys - Reroll stock for general applications - Specifications for hot rolled reroll stock |
| BS EN 12482-2-1998 | 铝和铝合金.通用重轧胚料.冷轧重轧胚料规范. | Aluminium and aluminium alloys - Reroll stock for general applications - Specifications for cold rolled reroll stock |
| BS EN 12487-2007 | 金属的腐蚀防护.铝和铝合金上经清洗和未清洗的铬酸盐转化涂层 | Corrosion protection of metals - Rinsed and non-rinsed chromate conversion coatings on aluminium and aluminium alloys |
| BS EN 12501-2-2003 | 金属材料的防腐蚀.土壤中腐蚀可能性.低合金和非合金黑色金属材料 | Protection of metallic materials against corrosion - Corrosion likelihood in soil - Low alloyed and non alloyed ferrous materials |
| BS EN 12502-2-2005 | 金属材料腐蚀防护.配水和蓄水系统中腐蚀可能性的评价指南.铜和铜合金的影响因素 | Protection of metallic materials against corrosion - Guidance on the assessment of corrosion likelihood in water distribution and storage systems - Influencing factors for copper and copper alloys |
| BS EN 12502-5-2005 | 金属材料腐蚀防护.配水和蓄水系统中腐蚀可能性的评价指南.铸铁、非合金和低合金钢的影响因素 | Protection of metallic materials against corrosion - Guidance on the assessment of corrosion likelihood in water distribution and storage systems - Influencing factors for cast iron, unalloyed and low alloyed steels |
| BS EN 12508-2000 | 金属和合金的腐蚀保护.表面处理,金属和其它无机涂层.术语 | Corrosion protection of metals and alloys - Surface treatment, metallic and other inorganic coatings - Vocabulary |
| BS EN 12517-1-2006 | 焊缝的无损检验.用放射线照相术评定钢、镍、钛及其合金的焊接接缝.验收等级 | Non-destructive testing of welds - Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels |
| BS EN 12536-2000 | 焊料.非合金钢和抗蠕变钢气焊焊条.分类 | Welding consumables - Rods for gas welding of non alloy and creep-resisting steels - Classification |
| BS EN 1254-1-1998 | 铜和铜合金.管路接头.铜管毛细管钎焊法或铜焊法用端头接头 | Copper and copper alloys - Plumbing fittings - Fittings with ends for capillary soldering or capillary brazing to copper tubes |
| BS EN 1254-2-1998 | 铜和铜合金.管路接头.与铜管一起使用的压合接头 | Copper and copper alloys - Plumbing fittings - Fittings with compression ends for use with copper tubes |
| BS EN 1254-3-1998 | 铜和铜合金.管路接头.与塑料管一起使用的压合接头 | Copper and copper alloys - Plumbing fittings - Fittings with compression ends for use with plastics pipes |
| BS EN 1254-4-1998 | 铜和铜合金.管路接头.与带有毛细管或压力端头的其它端头连接的管接头 | Copper and copper alloys - Plumbing fittings - Fittings combining other end connections with capillary or compression ends |
| BS EN 1254-5-1998 | 铜和铜合金.管路接头.铜管毛细管铜焊法用短端头接头 | Copper and copper alloys - Plumbing fittings - Fittings with short ends for capillary brazing to copper tubes |
| BS EN 12548-1999 | 铅和合金.电缆护套和套筒用铅合金锭 | Lead and alloys - Lead alloy ingots for electric cable sheathing and for sleeves |
| BS EN 12588-2006 | 铅和铅合金.建筑用轧制薄铅板 | Lead and lead alloys — Rolled lead sheet for building purposes |
| BS EN 12659-1999 | 铅和铅合金.铅 | Lead and lead alloys - Lead |
| BS EN 12735-1-2001 | 铜和铜合金.空调和制冷用无缝圆铜管.管道系统用管 | Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Tubes for piping systems |
| BS EN 12735-2-2001 | 铜和铜合金.空调和制冷用无缝圆铜管.设备用管 | Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Tubes for equipment |
| BS EN 12844-1999 | 锌和锌合金.铸件.规范 | Zinc and zinc alloys - Castings - Specifications |
| BS EN 12861-1999 | 铜及铜合金.废料 | Copper and copper alloys - Scrap |
| BS EN 12862-2000 | 可运输气瓶.可反复灌装可运输焊接铝合金气瓶的设计和制造规范 | Transportable gas cylinders - Specification for the design and construction of refillable transportable welded aluminium alloy gas cylinders |
| BS EN 12893-2000 | 铜和铜合金.螺旋拉伸数测定 | Copper and copper alloys - Determination of spiral elongation number |
| BS EN 12938-2000 | 锡铅合金分析方法.原子光谱法测定合金和杂质元素含量 | Methods for the analysis of pewter - Determination of alloying and impurity element contents by atomic spectrometry |
| BS EN 1301-1-1997 | 铝和铝合金.拉制丝材.检验和交付技术状态 | Aluminium and aluminium alloys - Drawn wire - Technical conditions for inspection and delivery |
| BS EN 1301-2-1997 | 铝和铝合金.冷拉丝材.机械性能 | Aluminium and aluminium alloys - Drawn wire - Mechanical properties |
| BS EN 1301-3-1997 | 铝和铝合金.拉制丝材.尺寸公差 | Aluminium and aluminium alloys - Drawn wire - Tolerances on dimensions |
| BS EN 13086-2000 | 铅及铅合金.氧化铅 | Lead and lead alloys - Lead oxides |
| BS EN 13147-2001 | 铜和铜合金.带材宽面上残余应力测定 | Copper and copper alloys - Determination of residual stresses in the border area of a slit strip |
| BS EN 13148-2002 | 铜及铜合金.热浸镀锡的铜带材 | Copper and copper alloys - Hot-dip tinned strip |
| BS EN 13195-1-2002 | 铝和铝合金.海上(造船业,海运和近海工程)用煅造和铸造产品.规范 | Aluminium and aluminium alloys - Wrought and cast products for marine applications (shipbuilding, marine and offshore) - Specifications |
| BS EN 13283-2002 | 锌和锌合金.再生锌 | Zinc and zinc alloys - Secondary zinc |
| BS EN 13347-2002 | 铜和铜合金.焊接和钎焊用杆材和线材 | Copper and copper alloys - Rod and wire for welding and braze welding |
| BS EN 13348-2001 | 铜和铜合金.医用气体或真空用无缝圆铜管 | Copper and copper alloys - Seamless, round copper tubes for medical gases or vacuum |
| BS EN 13349-2002 | 铜和铜合金.带固体遮敝物的预绝缘铜管 | Copper and copper alloys - Pre-insulated copper tubes with solid covering |
| BS EN 13445-8-2006 | 非受火压力容器.铝和铝合金压力容器附加要求 | Unfired pressure vessels - Additional requirements for pressure vessels of aluminium and aluminium alloys |
| BS EN 13480-8-2007 | 金属工业管道.铝和铝合金管道附加要求 | Metallic industrial piping - Additional requirements for aluminium and aluminium alloy piping |
| BS EN 13599-2002 | 铜和铜合金.电气用的铜厚板材、薄板材和带材 | Copper and copper alloys - Copper plate, sheet and strip for electrical purposes |
| BS EN 13600-2002 | 铜和铜合金.电气用的无缝铜管 | Copper and copper alloys - Seamless copper tubes for electrical purposes |
| BS EN 13601-2002 | 铜和铜合金.一般电气用的铜杆、铜棒和铜丝 | Copper and copper alloys - Copper rod, bar and wire for general electrical purposes |
| BS EN 13602-2002 | 铜和铜合金.制造导电体用的拉拔圆铜丝线 | Copper and copper alloys - Drawn, round copper wire for the manufacture of electrical conductors |
| BS EN 13603-2002 | 铜和铜合金.评估电气用的拉拔圆铜丝上锡覆层的试验方法 | Copper and copper alloys - Test methods for assessing protective tin coatings on drawn round copper wire for electrical purposes |
| BS EN 13604-2002 | 铜和铜合金.电子管、半导体器件和真空设备用高电导率铜的制品 | Copper and copper alloys - Products of high conductivity copper for electronic tubes, semiconductor devices and vacuum applications |
| BS EN 13605-2002 | 铜和铜合金.电气用铜型材和成型的铜丝材 | Copper and copper alloys - Copper profiles and profiled wire for electrical purposes |
| BS EN 13828-2003 | 建筑物用阀.建筑物内饮用水供给用手动铜合金及不锈钢球阀.试验及要求 | Building valves - Manually operated copper alloy and stainless steel ball valves for potable water supply in buildings - Tests and requirements |
| BS EN 1386-2007 | 铝和铝合金.踏板.规范 | Aluminium and aluminium alloys - Tread plate - Specifications |
| BS EN 13920-1-2003 | 铝和铝合金.废料.一般要求、取样和试验 | Aluminium and aluminium alloys - Scrap - General requirements, sampling and tests |
| BS EN 13920-10-2003 | 铝和铝合金.废料.铝制废饮料罐的废料 | Aluminium and aluminium alloys - Scrap - Scrap consisting of used aluminium beverage cans |
| BS EN 13920-11-2003 | 铝和铝合金.废料.铝铜散热器的废料 | Aluminium and aluminium alloys - Scrap - Scrap consisting of aluminium-copper radiators |
| BS EN 13920-12-2003 | 铝和铝合金.废料.单一合金的车床切屑 | Aluminium and aluminium alloys - Scrap - Turnings consisting of one single alloy |
| BS EN 13920-13-2003 | 铝和铝合金.废料.含两种或多种合金的混合车床切屑 | Aluminium and aluminium alloys - Scrap - Mixed turnings consisting of two or more alloys |
| BS EN 13920-14-2003 | 铝和铝合金.废料.废铝包装件 | Aluminium and aluminium alloys - Scrap - Scrap from post-consumer aluminium packagings |
| BS EN 13920-15-2003 | 铝和铝合金.废料.已去除废铝包装件中涂层的铝废料 | Aluminium and aluminium alloys - Scrap - Decoated aluminium scrap from post-consumer aluminium packagings |
| BS EN 13920-16-2003 | 铝和铝合金.废料.浮渣、渣滓、疤皮和金属粒子的废料 | Aluminium and aluminium alloys - Scrap - Scrap consisting of skimmings, drosses, spills and metallics |
| BS EN 13920-2-2003 | 铝和铝合金.废料.非合金废铝 | Aluminium and aluminium alloys - Scrap - Unalloyed aluminium scrap |
| BS EN 13920-3-2003 | 铝和铝合金.废料.废金属丝和电缆 | Aluminium and aluminium alloys - Scrap - Wire and cable scrap |
| BS EN 13920-4-2003 | 铝和铝合金.废料.单一锻造合金的废料 | Aluminium and aluminium alloys - Scrap - Scrap consisting of one single wrought alloy |
| BS EN 13920-5-2003 | 铝和铝合金.废料.同一系列两种或多种锻造合金的废料 | Aluminium and aluminium alloys - Scrap - Scrap consisting of two or more wrought alloys of the same series |
| BS EN 13920-6-2003 | 铝和铝合金.废料.含两种或多种锻造铝合金的废料 | Aluminium and aluminium alloys - Scrap - Scrap consisting of two or more wrought alloys |
| BS EN 13920-7-2003 | 铝和铝合金.废料.铸件废料 | Aluminium and aluminium alloys - Scrap - Scrap consisting of castings |
| BS EN 13920-8-2003 | 铝和铝合金.废料.为实施铝分离加工，含粉碎加工产生的 非铁材料废料 | Aluminium and aluminium alloys - Scrap - Scrap consisting of non-ferrous materials from shredding processes destined to aluminium separation processes |
| BS EN 13920-9-2003 | 铝和铝合金.废料.从粉碎的非铁材料中分离出的铝废料 | Aluminium and aluminium alloys - Scrap - Scrap from aluminium separation processes of non-ferrous shredded materials |
| BS EN 13957-2003 | 铝和铝合金.一般用途挤压圆形盘管.规范 | Aluminium and aluminium alloys - Extruded round, coiled tube for general applications - Specification |
| BS EN 13958-2003 | 铝和铝合金.一般用途冷拉圆形盘管.规范 | Aluminium and aluminium alloys - Cold drawn, round coiled tube for general applications - Specification |
| BS EN 1396-1997 | 铝及铝合金.一般用途的成卷包敷的薄板和带材规范 | Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications |
| BS EN 13981-1-2003 | 铝和铝合金.结构性铁道制品.检验和交货技术条件.挤压制品 | Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Extruded products |
| BS EN 13981-2-2004 | 铝和铝合金.结构性轨道用制品.检验和交货技术条件.板材和薄板材 | Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Plates and sheets |
| BS EN 13981-3-2006 | 铝和铝合金.结构性铁路设施用产品.检验和交货用技术条件.铸件 | Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Castings |
| BS EN 13981-4-2006 | 铝和铝合金.结构性铁道设施用产品.检验和交货技术条件.锻制品 | Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Forgings |
| BS EN 14057-2003 | 铅和铅合金.碎片.术语和定义 | Lead and lead alloys - Scraps - Terms and definitions |
| BS EN 1412-1996 | 铜和铜合金.欧洲牌号系统 | Copper and copper alloys - European numbering system |
| BS EN 14121-2003 | 铝和铝合金.电工用铝薄板、带材和板材 | Aluminium and aluminium alloys - Aluminium sheet, strip and plate for electrotechnical applications |
| BS EN 14242-2004 | 铝和铝合金.化学分析.感应耦合等离子体光学辐射光谱分析 | Aluminium and aluminium alloys - Chemical analysis - Inductively coupled plasma optical emission spectral analysis |
| BS EN 14286-2007 | 铝和铝合金.危险物品存储和运输用容器可焊接卷状产品 | Aluminium and aluminium alloys - Weldable rolled products for tanks for the storage and transportation of dangerous goods |
| BS EN 14287-2004 | 铝和铝合金.包装和包装元件制造用产品的化学成分的具体要求 | Aluminium and aluminium alloys - Specific requirements on the chemical composition of products intended to be used for the manufacture of packaging and packaging components |
| BS EN 14290-2004 | 锌和锌合金.二次原料 | Zinc and zinc alloys - Secondary raw material |
| BS EN 14361-2004 | 铝和铝合金.化学分析.金属熔料抽样 | Aluminium and aluminium alloys - Chemical analysis - Sampling from metal melts |
| BS EN 14436-2004 | 铜和铜合金.电镀锡带 | Copper and copper alloys - Electrolytically tinned strip |
| BS EN 14532-1-2004 | 焊接消耗品.试验方法和质量要求.钢、镍和镍合金消耗品的基本方法和合格评定 | Welding consumables - Test methods and quality requirements - Primary methods and conformity assessment of consumables for steel, nickel and nickel alloys |
| BS EN 14532-2-2004 | 焊接消耗品.试验方法和质量要求.钢、镍和镍合金耗材的补充方法和合格评定 | Welding consumables - Test methods and quality requirements - Supplementary mekthods and conformity assessment of consumables for steel, nickel and nickel alloys |
| BS EN 14532-3-2005 | 焊接消耗品.试验方法和质量要求.铝合金焊接用焊丝电极、焊丝和焊棒的合格评定 | Welding consumables - Test methods and quality requirements - Conformity assessment of wire electrodes, wires and rods for welding of aluminium alloys |
| BS EN 14640-2005 | 焊接消耗品.铜和铜合金熔焊用实心焊丝和焊棒.分类 | Welding consumables - Solid wires and rods for fusion welding of copper and copper alloys - Classification |
| BS EN 14726-2005 | 铝和铝合金.化学分析.闪光光学发射光谱测定分析指南 | Aluminium and aluminium alloys - Chemical analysis - Guideline for spark optical emission spectrometric analysis |
| BS EN 14935-2006 | 铜和铜合金.测定纯铜杂质.ETA-AAS法 | Copper and copper alloys - Determination of impurities in pure copper - ETA-AAS method |
| BS EN 14936-1-2006 | 铜和铜合金.铝含量的测定.滴定法 | Copper and copper alloys - Determination of aluminium content - Titrimetric method |
| BS EN 14936-2-2006 | 铜和铜合金.铝含量的测定.FAAS法 | Copper and copper alloys - Determination of aluminium content - FAAS method |
| BS EN 14937-1-2006 | 铜和铜合金.锑含量的测定.分光光度测量法 | Copper and copper alloys - Determination of antimony content - Spectrophotometric method |
| BS EN 14937-2-2006 | 铜和铜合金.锑含量的测定.FAAS法 | Copper and copper alloys - Determination of antimony content - FAAS method |
| BS EN 14939-2006 | 铜和铜合金.测定铍含量.FAAS法 | Copper and copper alloys - Determination of beryllium content - FAAS Method |
| BS EN 14940-2-2006 | 铜和铜合金.铬含量的测定.FAAS法 | Copper and copper alloys - Determination of chromium content - FAAS method |
| BS EN 14941-2006 | 铜和铜合金.测定钴含量.FAAS法 | Copper and copper alloys - Determination of cobalt content - FAAS method |
| BS EN 14942-2-2006 | 铜和铜合金.砷含量的测定.FAAS法 | Copper and copper alloys - Determination of arsenic content - FAAS method |
| BS EN 14945-2005 | 耐火制品和材料.使用前后的铬合金耐火材料中铬(VI)的光谱测定法测定 | Refractory products and materials - Spectrometric determination of chromium (VI) in chrome bearing refractories, before and after use |
| BS EN 14977-2006 | 铜和铜合金.抗拉应力的检测.5%氨试验 | Copper and copper alloys - Detection of tensile stress - 5% ammonia test |
| BS EN 15022-3-2006 | 铜和铜合金.锡含量的测定.低锡含量.火焰原子吸收光谱测定法(FAAS) | Copper and copper alloys - Determination of tin content - Low tin content - Flame atomic absorption spectrometry method (FAAS) |
| BS EN 15024-2-2006 | 铜和铜合金.锌含量的测定.第2部分:火焰原子吸收光谱法(FAAS) | Copper and copper alloys - Determination of zinc content -Part 2: Flame atomic absorption spectrometry method (FAAS) |
| BS EN 1503-4-2002 | 阀门.阀体、阀帽和阀盖用材料.欧洲标准中规定的铜合金 | Valves - Materials for bodies, bonnets and covers - Copper alloys specified in European Standards |
| BS EN 15063-1-2006 | 铜和铜合金.用波长色散X射线荧光光谱测定法(XRF)测定主要元素和杂质.常规方法指南 | Copper and copper alloys - Determination of main constituents and impurities by wavelength dispersive X-ray fluorescence spectrometry (XRF) - Guidelines to the routine method |
| BS EN 15063-2-2006 | 铜和铜合金.用波长色散X射线荧光光谱测定法(XRF)测定主要元素和杂质.常规方法 | Copper and copper alloys - Determination of main constituents and impurities by wavelength dispersive X-ray fluorescence spectrometry (XRF) - Routine method |
| BS EN 15079-2007 | 铜和铜合金.火花源发射光谱测定法(S-OES)分析 | Copper and copper alloys - Analysis by spark source optical emission spectrometry (S-OES) |
| BS EN 15088-2005 | 铝和铝合金.施工作业用结构产品.检验和交付用技术条件 | Aluminium and aluminium alloys - Structural products for construction works - Technical conditions for inspection and delivery |
| BS EN 1559-4-1999 | 铸造.交付技术状态.铝合金铸件的附加要求 | Founding - Technical conditions of delivery - Additional requirements for aluminium alloy castings |
| BS EN 1559-5-1998 | 铸造.交货技术条件.镁合金铸件的附加要求 | Founding - Technical conditions of delivery - Additional requirements for magnesium alloy castings |
| BS EN 1559-6-1999 | 铸造.交付技术状态.锌合金铸件附加要求 | Founding - Technical conditions of delivery - Additional requirements for zinc alloy castings |
| BS EN 1592-1-1998 | 铝和铝合金.HF缝焊管.检验和交付技术状态 | Aluminium and aluminium alloys - HF seam welded tubes - Technical conditions for inspection and delivery |
| BS EN 1592-2-1998 | 铝和铝合金.HF缝焊管.机械特性 | Aluminium and aluminium alloys - HF seam welded tubes - Mechanical properties |
| BS EN 1592-3-1998 | 铝和铝合金.HF缝焊管.圆形管的尺寸和形状公差 | Aluminium and aluminium alloys - HF seam welded tubes - Tolerances on dimensions and form for circular tubes |
| BS EN 1592-4-1998 | 铝和铝合金.HF缝焊管.正方形、矩形和异型管的尺寸和形状公差 | Aluminium and aluminium alloys - HF seam welded tubes - Tolerances on dimensions and form for square, rectangular and shaped tubes |
| BS EN 1597-1-1997 | 焊接用料.试验方法 .钢,镍和镍合金中所有焊接金属试样备制用的试件 | Welding consumables - Test methods - Test piece for all-weld metal test specimens in steel, nickel and nickel alloys |
| BS EN 1652-1998 | 铜和铜合金.一般用途的板材、薄板材、带材和圆形材 | Copper and copper alloys - Plate, sheet, strip and circles for general purposes |
| BS EN 1653-1998 | 铜和铜合金.锅炉、压力容器和热水保温装置用的板、薄板材和圆形材 | Copper and copper alloys - Plate, sheet and circles for boilers, pressure vessels and hot water storage units |
| BS EN 1654-1998 | 铜和铜合金.弹簧和连接器用带材 | Copper and copper alloys - Strip for springs and connectors |
| BS EN 1655-1997 | 铜和铜合金.符合性声明 | Copper and copper alloys - Declarations of conformity |
| BS EN 1668-1997 | 焊接用料.非合金和细晶粒钢和钨极惰性气体保护用的焊条,焊丝和沉积物.分类 | Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non alloy and fine grain steels - Classification |
| BS EN 1669-1997 | 铝及铝合金试验方法.薄板材和带材的耳索试验 | Aluminium and aluminium alloys - Test methods - Earing test for sheet and strip |
| BS EN 1676-1997 | 铝及铝合金试验方法.再熔用的合金铸锭.规范 | Aluminium and aluminium alloys - Alloyed ingots for remelting - Specifications |
| BS EN 1706-1998 | 铝及铝合金.铸件.化学成分和机械特性 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| BS EN 1715-1-1998 | 铝和铝合金.拉制坯料.检验和交货技术条件及一般要求 | Aluminium and aluminium alloys - Drawing stock - General requirements and technical conditions for inspection and delivery |
| BS EN 1715-2-1998 | 铝和铝合金.绘图台.电气应用的特殊要求 | Aluminium and aluminium alloys - Drawing stock - Specific requirements for electrical applications |
| BS EN 1715-3-1998 | 铝和铝合金.拉制坯料.机械用.特殊要求(不包括焊接) | Aluminium and aluminium alloys - Drawing stock - Specific requirements for mechanical uses (excluding welding) |
| BS EN 1715-4-1998 | 铝和铝合金.拉制坯料.焊接用.特殊要求 | Aluminium and aluminium alloys - Drawing stock - Specific requirements for welding applications |
| BS EN 1753-1997 | 镁和镁合金.镁合金铸模和铸件 | Magnesium and magnesium alloys - Magnesium alloy ingots and castings |
| BS EN 1754-1997 | 镁和镁合金.镁和镁合金阳极、铸锭、铸件.设计系统 | Magnesium and magnesium alloys - Magnesium and magnesium alloy anodes, ingots and castings - Designation system |
| BS EN 1758-1998 | 铜及铜合金.引线框架用带材 | Copper and copper alloys - Strip for lead frames |
| BS EN 1759-3-2004 | 法兰及其连接件.标注等级的管道、阀门、配件和附件用圆形法兰.铜合金法兰 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, class designated - Copper alloy flanges |
| BS EN 1759-4-2003 | 法兰及其连接件.标注等级的管道、阀门、配件及附件用圆形法兰.铝合金法兰 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, class designated - Aluminium alloy flanges |
| BS EN 1774-1998 | 锌和锌合金.铸造用合金.铸锭和熔液 | Zinc and zinc alloys - Alloys for foundry purposes - Ingot and liquid |
| BS EN 1780-1-2002 | 铝和铝合金.再熔、母合金和铸件的非合金和合金铝锭的命名.数字命名系统 | Aluminium and aluminium alloys - Designation of unalloyed and alloyed aluminium ingots for remelting, master alloys and castings - Numerical designation system |
| BS EN 1780-2-2002 | 铝和铝合金.再熔、母合金和铸件用非合金和合金铝锭的命名.用化学符号表示命名系统 | Aluminium and aluminium alloys - Designation of unalloyed and alloyed aluminium ingots for remelting, master alloys and castings - Chemical symbol based designation system |
| BS EN 1780-3-2002 | 铝和铝合金.再熔、母合金和铸件的非合金和合金铝锭的命名.化学成份的书写规则 | Aluminium and aluminium alloys - Designation of unalloyed and alloyed aluminium ingots for remelting, master alloys and castings - Writing rules for chemical composition |
| BS EN 1802-2002 | 可运输储气瓶.无缝铝合金储气瓶的周期性检验和测试 | Transportable gas cylinders - Periodic inspection and testing of seamless aluminium alloy gas cylinders |
| BS EN 1904-2000 | 贵重金属.贵重金属珠宝合金适焊性 | Precious metals - The finenesses of solders used with precious metal jewellery alloys |
| BS EN 1971-1999 | 铜和铜合金.管材的涡流试验 | Copper and copper alloys - Eddy current test for tubes |
| BS EN 1975-2000 | 便携气体钢瓶.容量由0,5升到150升(包括150升)的由无缝铝和铝合金制气体瓶的设计和结构规范. | Transportable gas cylinders - Specification for the design and construction of refillable transportable seamless aluminium and aluminium alloy gas cylinders of capacity from 0,5 litre up to 150 litre |
| BS EN 1976-1998 | 铜及铜合金.未定形铜铸件产品 | Copper and copper alloys - Cast unwrought copper products |
| BS EN 1977-1998 | 铜及铜合金.铜拉制坯料(线杆材) | Copper and copper alloys - Copper drawing stock (wire rod) |
| BS EN 1978-1998 | 铜及铜合金.铜阴极 | Copper and copper alloys - Copper cathodes |
| BS EN 1981-2003 | 铜及铜合金.母合金 | Copper and copper alloys - Master alloys |
| BS EN 1982-1999 | 铜和铜合金.铸锭和铸件 | Copper and copper alloys - Ingots and castings |
| BS EN 2003-009-2007 | 航空航天系列.试验方法.钛和钛合金.表面污染测定 | Aerospace series - Test methods - Titanium and titanium alloys - Determination of surface contamination |
| BS EN 2003-010-2007 | 航空航天系列.钛和钛合金.试验方法.抽样测定氢含量 | Aerospace series - Titanium and titanium alloys - Test methods - Sampling for determination of hydrogen content |
| BS EN 2004-1-1993 | 铝和铝合金产品试验方法.第1部分:锻铝合金电导率的测定 | Test methods for aluminium and aluminium alloy products - Determination of electrical conductivity of wrought aluminium alloys |
| BS EN 2004-5-1993 | 铝和铝合金产品试验方法.第5部分:复合半成品的包层厚度和铜扩散的测定 | Test methods for aluminium and aluminium alloy products - Determination of cladding thickness and copper diffusion of clad semi-finished products |
| BS EN 2044-2001 | 航空航天系列.铝及铝合金拉制圆棒.公差等级h11.直径为4mm D 63mm.尺寸 | Aerospace series - Round bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Diameter 4 mm D 63 mm - Dimensions |
| BS EN 2045-2001 | 航空航天系列.铝及铝合金拉制方棒.公差等级h11.厚度为6mm a 50mm.尺寸 | Aerospace series - Square bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Thickness 6 mm a 50 mm - Dimensions |
| BS EN 2046-2001 | 铝及铝合金拉制六角形棒材.公差等级h11.对边宽度为7mm a 50mm.尺寸 | Hexagonal bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Width across flats 7 mm a 50 mm - Dimensions |
| BS EN 2047-2001 | 航空航天系列.带边的L形铝及铝合金挤压件.尺寸 | Aerospace series - Beaded L-section extruded, in aluminium and aluminium alloys - Dimensions |
| BS EN 2048-2001 | 航空航天系列.铝合金L形挤压型材.尺寸 | Aerospace series - Extruded L-section in aluminium alloys - Dimensions |
| BS EN 2049-2001 | 航空航天系列.U形铝及铝合金挤压件.尺寸 | Aerospace series - Extruded channel section, in aluminium alloys - Dimensions |
| BS EN 2050-2001 | 航空航天系列.T形铝及铝合金挤压件.尺寸 | Aerospace series - Extruded T-section, in aluminium alloys - Dimensions |
| BS EN 2066-2002 | 航空航天系列.铝合金挤制型材.一般公差 | Aerospace series - Extruded section in aluminium alloys - General tolerances |
| BS EN 2070-1-1991 | 铝和铝合金锻制品规范.技术规范.一般要求 | Specification for aluminium and aluminium alloy wrought products - Technical specification - General requirements |
| BS EN 2070-2-1991 | 铝和铝合金锻制品规范.技术规范.薄板材、带成形的型材和中厚板材 | Specification for aluminium and aluminium alloy wrought products - Technical specification - Sheet, strip formed profiles and plate |
| BS EN 2070-3-1991 | 铝和铝合金锻制品规范.技术规范.棒材和型材 | Specification for aluminium and aluminium alloy wrought products - Technical specification - Bar and section |
| BS EN 2070-4-1991 | 铝和铝合金锻制产品规范.技术规范.结构管材 | Specification for aluminium and aluminium alloy wrought products - Technical specification - Tube for structures |
| BS EN 2070-5-1991 | 铝和铝合金锻制品规范.技术规范.承压用的管材 | Specification for aluminium and aluminium alloy wrought products - Technical specification - Tube used under pressure |
| BS EN 2070-6-1991 | 铝和铝合金锻制品规范.技术规范.铆钉丝材 | Specification for aluminium and aluminium alloy wrought products - Technical specification - Rivet wire |
| BS EN 2070-7-1991 | 铝和铝合金锻制品规范.技术规范.锻坯 | Specification for aluminium and aluminium alloy wrought products - Technical specification - Wrought forging stock |
| BS EN 2071-2002 | 航空航天系列.铝及铝合金板.厚度为0.25mm a 6mm.尺寸 | Aerospace series - Sheets in aluminium and aluminium alloys - Thickness 0,25 mm a 6 mm - Dimensions |
| BS EN 2072-2005 | 航空航天系列.AL-P1050A-H14型铝合金.薄板材和带材.0.4mm≤a≤6mm | Aerospace series - Aluminium AL-P1050A - H14 - Sheet and strip - 0,4 mm <= a <= 6 mm |
| BS EN 2076-1-1991 | 铝和镁合金铸锭和铸件.技术规范.一般要求 | Aluminium and magnesium alloy ingots and castings - Technical specification - General requirements |
| BS EN 2076-2-1991 | 铝和镁合金铸锭和铸件.技术规范.重熔用的铸锭 | Aluminium and magnesium alloy ingots and castings - Technical specification - Ingots for remelting |
| BS EN 2076-3-1991 | 铝和镁合金铸锭和铸件.技术规范.预生产铸件和生产铸件 | Aluminium and magnesium alloy ingots and castings - Technical specification - Pre-production and production castings |
| BS EN 2082-1-1991 | 铝合金锻坯和锻件规范.技术规范.一般要求 | Specification for aluminium alloy forging stock and forgings - Technical specification - General requirements |
| BS EN 2082-2-1991 | 铝合金锻坯和锻件规范.技术规范.锻坯 | Specification for aluminium alloy forging stock and forgings - Technical specification - Forging stock |
| BS EN 2082-3-1991 | 铝合金锻坯和锻件规范.技术规范.试生产锻件和生产锻件 | Specification for aluminium alloy forging stock and forgings - Technical specification - Pre-production and production forgings |
| BS EN 2083-2001 | 航空航天系列.电缆用铜及铜合金导体.产品标准 | Aerospace series - Copper and copper alloy conductors for electrical cables - Product standard |
| BS EN 2084-2005 | 航空航天系列.单芯、通用、带铜或铜合金导体的电缆.技术规范 | Cables, electric, single-core, general purpose, with conductors in copper or copper alloy — Technical specification |
| BS EN 2085-2005 | 航空航天系列.铝合金AL-P2618A-T6.手锻和模锻件.a150 mm | Aerospace series - Aluminium alloy AL-P2618A-T6 - Hand and die forgings - a 150 mm |
| BS EN 2086-2005 | 航空航天系列.铝合金AL-P2618A-T851.手锻和模锻.a150 mm | Aerospace series - Aluminium alloy AL-P2618A-T851 - Hand and die forgings - a 150 mm |
| BS EN 2087-2005 | 航空航天系列. 铝合金ALP2014A.T6 或 T62型.0.4 mm <= a <= 6 mm的层覆薄板材和带材 | Aerospace series - Aluminium alloy AL-P2014A - T6 or T62 - Clad sheet & strip 0,4 mm <= a <= 6 mm |
| BS EN 2088-2005 | 航空航天系列.AL-P2014A-T4型或AL-P2014A-T42型铝合金.覆层薄板材和带材.0.4mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P2014A - T4 or T42 - Clad sheet and strip - 0,4 mm <= a <= 6 mm |
| BS EN 2089-2005 | AL-P2014A T6或T62铝合金.0.4mm-6mm的薄板及带材 | Aluminium alloy AL-P2014A T6 or T62 - Sheet and strip - 0,4 mm a 6 mm |
| BS EN 2090-2005 | 铝合金AL-P2024-T3.覆层薄板和带材.0.3 mm≤a≤6 mm | Aluminium alloy AL-P2024-T3 - Clad sheet and strip - 0,3 mm a 6 mm |
| BS EN 2092-2005 | 航空航天系列.铝合金AL-P7075.T6或T62.覆层铝合金板材及带材.0.4mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P7075-T6 or T62 - Clad sheet and strip - 0,4 mm a 6 mm |
| BS EN 2093-1992 | AL-P 7009-T74铝合金.20mm≤a≤150mm手工锻件 | Aluminium alloy AL-P7009-T74 - Hand forgings 20 mm a 150 mm |
| BS EN 2094-1992 | AL-P 7009-T74铝合金.3mm≤a≤150mm模锻件 | Aluminium alloy AL-P7009-T74 - Die forgings 3 mm a 150 mm |
| BS EN 2100-1992 | AL-P2014A-T4511铝合金.a或D≤200mm的挤压棒材和型材 | Aluminium alloy AL-P2014A-T4511 - Extruded bars and sections a or D 200 mm |
| BS EN 2101-1991 | 铝合金和锻铝合金铬酸阳极化规范 | Specification for chromic acid anodizing of aluminium and wrought aluminium alloys |
| BS EN 2103-1-1992 | 钢、镍基合金及钴基合金重熔坯料和铸件.技术规范.一般要求 | Steel, nickel base and cobalt base alloy remelting stock and castings - Technical specification - General requirements |
| BS EN 2103-2-1992 | 钢、镍基合金及钴基合金重熔坯料和铸件.技术规范.重熔坯料 | Steel, nickel base and cobalt base alloy remelting stock and castings - Technical specification - Remelting stock |
| BS EN 2103-3-1992 | 钢、镍基合金及钴基合金重熔坯料和铸件.技术规范.试制铸件和产品铸件 | Steel, nickel base and cobalt base alloy remelting stock and castings - Technical specification - Pre-production and production castings |
| BS EN 2122-1996 | 经阳极电镀或铬酸盐处理的扁平铝合金垫圈 | Washers, flat, in aluminium alloy, anodized or chromated |
| BS EN 2126-1992 | AL-P7075-T651铝合金.6mm≤a≤80mm板材 | Aluminium alloy AL-P7075-T651 - Plate 6 mm a 80 mm |
| BS EN 2127-1992 | AL-P7075-T73511铝合金.a或D≤100mm的挤压棒材和型材 | Aluminium alloy AL-P7075-T73511 - Extruded bars and sections a or D 100 mm |
| BS EN 2128-1992 | AL-P7075-T7351铝合金.6mm≤a或D≤75mm拉制棒材 | Aluminium alloy AL-P7075-T7351 - Drawn bars 6 mm a or D 75 mm |
| BS EN 2131-2002 | 航空航天系列.铝合金板.厚度6mm < a> 160mm.尺寸 | Aerospace series - Plates in aluminium alloys - Thickness 6 mm a 160 mm - Dimensions |
| BS EN 2133-1998 | 具有规定拉力强度(LE)1450 MPa的钢、铜、铜合金和镍合金的镉镀层 | Cadmium plating of steels with specified tensile strength 1450 MPa, copper, copper alloys and nickel alloys |
| BS EN 2134-2002 | 航空航天系列.铝及铝合金挤制圆棒.直径为10mm D 220mm.尺寸 | Aerospace series - Round bars, extruded in aluminium and aluminium alloys - Diameter 10 mm D 220 mm - Dimensions |
| BS EN 2144-1994 | 铝合金2117通用头型实心铆钉.英制系列 | Rivets, solid, universal head, in aluminium alloy 2117, inch based series |
| BS EN 2145-1994 | 英制系列的阳极氧化或铬酸盐处理的2117号铝合金通用头实心铆钉 | Rivets, solid, universal head, in aluminium alloy 2117, anodized or chromated, inch based series |
| BS EN 2149-1996 | 经阳极电镀或铬酸盐处理的5056A型铝合金通用头型实心铆钉.英制系列 | Rivets, solid, universal head, in aluminium alloy 5056A, anodized or chromated, inch based series |
| BS EN 2236-1992 | 合金钢紧公差钉体带头销钉.技术规范 | Pins, headed, close tolerance shank, in alloy steel - Technical specification |
| BS EN 2256-2005 | 航空航天系列.铝合金AL-P2618A-T852.手锻和模锻.a150 mm | Aerospace series - Aluminium alloy AL-P2618A-T852 - Hand and die forgings - a 150 mm |
| BS EN 2257-1997 | 铝和铝合金结构用圆管.直径为6mmD100mm.厚度为1mma6mm.尺寸 | Circular tubes for structures in aluminium and aluminium alloys - Diameter 6 mm D 100 mm - Thickness 1 mm a 6 mm - Dimensions |
| BS EN 2258-1997 | 铝和铝合金流体用圆管.直径为3.2mmD100mm.厚度为0.5mma2.5mm.尺寸 | Circular tubes for fluids in aluminium and aluminium alloys - Diameter 3,2 mm D 100 mm - Thickness 0,6 mm a 2,5 mm - Dimensions |
| BS EN 2264-1996 | 二硫化钼润滑的镀镉合金钢加大承窝安装的双耳浮动自锁托板螺母.等级:900MPa(室温)/235℃ | Nuts, anchor, self-locking, floating, two lug, incremental counterbore, in alloy steel, cadmium plated MoS2 lubricated - Classification: 900 MPa (at ambient temperature) /235 °C |
| BS EN 2284-1991 | 铝合金和锻铝合金硫酸阳极化规范 | Specification for sulfuric acid anodizing of aluminium and wrought aluminium alloys |
| BS EN 2285-1990 | 带自润滑内衬的铝合金普通套管规范.尺寸和负荷 | Specification for bushes plain, aluminium alloy with self-lubricating liner - Dimensions and loads |
| BS EN 2286-1990 | 带自润滑内衬的铝合金带法兰缘的套管规范.尺寸和负荷 | Specification for bushes flanged, aluminium alloy with self-lubricating liner - Dimensions and loads |
| BS EN 2289-1996 | 飞行控制用铝合金拉杆.技术规范 | Rod bodies in aluminium alloy for flight controls - Technical specification |
| BS EN 2290-1-1998 | 飞行控制可调节终端配合铝合金杆.尺寸和荷载 | Rod bodies, flight control in aluminium alloy, for adjustable end fittings - Dimensions and loads |
| BS EN 2318-1992 | AL-P2024-T3511铝合金.1,2mm≤a或D≤150mm的挤压棒材和型材 | Aluminium alloy AL-P2024-T3511 - Extruded bars and sections 1,2 mm a or D 150 mm |
| BS EN 2326-1992 | AL-P6082-T6铝合金.a或D≤200mm的挤压棒材和型材 | Aluminium alloy AL-P6082-T6 - Extruded bars and sections a or D 200 mm |
| BS EN 2327-2006 | 航空航天系列.飞行操纵杆用镉镀金合金钢制的径向锯齿锁紧垫圈.尺寸 | Aerospace series - Washers, lock, with radial serrations in alloy steel, cadmium plated for flight control rods - Dimensions |
| BS EN 23312-1993 | 绕结金属材料和硬质合金.杨氏模量的测定 | Sintered metal materials and hardmetals - Determination of Young modulus |
| BS EN 23326-1993 | 硬质合金.矫顽力（磁化强度）的测定 | Specification for hardmetals - Determination of (the magnetization) coercivity |
| BS EN 23327-1993 | 硬质合金.横向断裂强度的测定 | Hardmetals - Determination of transverse rupture strength |
| BS EN 2334-1997 | 铝和铝合金铬硫酸液 | Chromic-sulphuric acid pickle of aluminium and aluminium alloys |
| BS EN 23369-1993 | 密封烧结金属材料和硬质合金.密度的测定 | Impermeable sintered metal materials and hardmetals - Determination of density |
| BS EN 2338-2001 | 航空航天系列.热轧钛和钛合金薄板材.厚度为0.8mm 6mm.尺寸 | Aerospace series - Sheets, hot rolled in titanium and titanium alloys - Thickness 0,8 mm a 6 mm - Dimensions |
| BS EN 2339-2001 | 航空航天系列.冷轧钛和钛合金薄板材.厚度为0.2mm a 6mm.尺寸 | Aerospace series - Sheets, cold rolled in titanium and titanium alloys - Thickness 0,2 mm a 6 mm - Dimensions |
| BS EN 2344-2001 | 航空航天系列.耐热合金制的圆形棒材.直径大于10mm小于180mm.尺寸 | Aerospace series - Round bars, machined in heat resisting alloys - Diameter 10 mm D 180 mm - Dimensions |
| BS EN 2365-1989 | 铝合金轴环规范 | Specification for collars, aluminium alloy |
| BS EN 2381-1992 | AL-P7009-T7452铝合金.40mm≤a≤150mm的手工锻件 | Aluminium alloy AL-P7009-T7452 - Hand forgings 40 mm a 150 mm |
| BS EN 2384-1992 | AL-P2014-T6511铝合金.a或D≤150mm的挤压棒材和型材 | Aluminium alloy AL-P2014A-T6511 - Extruded bars and sections a or D 150 mm |
| BS EN 2385-1992 | AL-P7009-T74511铝合金.a或D≤125mm的挤压棒材和型材 | Aluminium alloy AL-P7009-T74511 - Extruded bars and sections a or D 125 mm |
| BS EN 23878-1993 | 硬质合金.维氏硬度试验 | Hardmetals - Vickers hardness test |
| BS EN 23908-1993 | 硬质合金.不溶性(游离)碳含量的测定.重量分析法 | Hardmetals - Determination of insoluble (free) carbon content - Gravimetric method |
| BS EN 23909-1994 | 硬质合金.钴含量测定.电位滴定法 | Hardmetals - Determination of cobalt - Potentiometric method |
| BS EN 2395-2005 | 航空航天系列.AL-P2014A-T4或T42铝合金.0.4mm≤a≤6mm 薄板和带材 | Aerospace series - Aluminium alloy AL-P2014A-T4 or T42 - Sheet and strip - 0,4 mm a 6 mm |
| BS EN 2413-1995 | 镀镉的合金钢短螺纹紧公差薄六角头带肩螺栓.等级:1100MPa(室温)/235℃ | Bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in alloy steel, cadmium plated - Classification: 1100 MPa (at ambient temperature)/235 °C |
| BS EN 2422-2005 | 铝合金AL-P2124-T351.板材.25 mm≤a≤120 mm | Aluminium alloy AL-P2124-T351 - Plate - 25 mm a 120 mm |
| BS EN 2437-2002 | 航空航天系列.铝及铝合金的铬酸盐转化涂层(黄色) | Aerospace series - Chromate conversion coatings (yellow) for aluminium and aluminium alloys |
| BS EN 24492-1993 | 硬质合金粉末以外的金属粉末.压实与绕结尺寸变化的测定 | Metallic powders, excluding powders for hardmetals - Determination of dimensional changes associated with compacting and sintering |
| BS EN 24499-1993 | 硬质合金规范.显微组织的金相测定 | Specification for hardmetals - Metallographic determination of microstructure |
| BS EN 24501-1994 | 硬质合金.钛含量测定.过氧化物光度法 | Hardmetals - Determination of titanium - Photometric peroxide method |
| BS EN 24503-1993 | 硬质合金.用X射线荧光分析法对金属元素含量的测定.熔化法 | Hardmetals - Determination of contents of metallic elements by X-ray fluorescence - Fusion method |
| BS EN 24505-1993 | 硬质合金规范.空隙度和游离碳的金相测定 | Specification for hardmetals - Metallographic determination of porosity and uncombined carbon |
| BS EN 24506-1993 | 硬质合金规范.压缩试验 | Specification for hardmetals - Compression test |
| BS EN 2486-2005 | 航天航空系列.AL-P2618A 型铝合金.锻坯件 | Aerospace series - Aluminium alloy AL-P2618A - Forging stock |
| BS EN 24883-1993 | 硬质合金规范.用X射线荧光分析法对金属元素含量的测定.溶液法 | Specification for hardmetals - Determination of contents of metallic elements by X-ray fluorescence - Solution method |
| BS EN 24884-1993 | 硬质合金.用烧结试块的粉末取样和试验 | Hardmetals - Sampling and testing of powders using sintered test pieces |
| BS EN 2497-1990 | 钛与钛合金干喷砂规范 | Specification for dry abrasive blasting of titanium and titanium alloys |
| BS EN 2511-2005 | 铝合金AL-P7075-T7351.板材.6 mm≤a≤100 mm | Aluminium alloy AL-P7075-T7351 - Plate - 6 mm a 100 mm |
| BS EN 2516-1997 | 耐腐蚀钢的钝化和镍基合金的纯化 | Passivation of corrosion resisting steels and decontamination of nickel base alloys |
| BS EN 2536-1995 | 铝合金的硬阳极氧化 | Hard anodizing of aluminium alloys |
| BS EN 2545-1-1995 | 钛和钛合金重熔料和铸件.技术规范.通用要求 | Titanium and titanium alloy remelting stock and castings - Technical specification - General requirements |
| BS EN 2545-2-1995 | 钛和钛合金重熔料和铸件.技术规范.第2部分:重熔料 | Titanium and titanium alloy remeling stock and castings - Technical specification - Remelting stock |
| BS EN 2545-3-1995 | 钛和钛合金重熔料和铸件.交付技术状态.第3部分:预生产铸件和生产铸件 | Titanium and titanium alloy remelting stock and castings - Technical specification - Pre-production and production castings |
| BS EN 2551-1993 | 2117型铝合金制100°标准埋头圆顶实心铆钉.英制系列 | Rivets, solid, 100 ° normal countersunk head with dome, in aluminium alloy 2117, inch based series |
| BS EN 2552-1993 | 经阳极氧化或铬酸盐表面处理的2117型铝合金制100°标准埋头圆顶实心铆钉.英制系列 | Rivets, solid, 100 ° normal countersunk head with dome, in aluminium alloy 2117, anodized or chromated, inch based series |
| BS EN 2553-1993 | 2017A型铝合金制100°标准埋头圆顶实心铆钉.英制系列 | Rivets, solid, 100 ° normal countersunk head with dome, in aluminium alloy 2017A, inch based series |
| BS EN 2555-1993 | 5056A型铝合金制100°标准埋头圆顶实心铆钉.英制系列 | Rivets, solid, 100 ° normal countersunk head with dome, in aluminium alloy 5056A, inch based series |
| BS EN 2556-1993 | 经阳极氧化或铬酸盐表面处理的5056A型铝合金制100°标准埋头圆顶实心铆钉.英制系列 | Rivets, solid, 100 ° normal countersunk head with dome, in aluminium alloy 5056A, anodized or chromated, inch based series |
| BS EN 2583-1997 | 耐热镍基合金NI-PH2601(铬镍铁合金718)MJ螺纹螺栓.等级:1275MPa(室温)/650℃.技术规范 | Bolts, MJ threads, in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification: 1275 MPa (at ambient temperature)/650 °C - Technical specification |
| BS EN 2599-2001 | 航空航天系列.铝和铝合金带材.厚度0.25mm,3.2mm.尺寸 | Aerospace series - Strips in aluminium and aluminium alloys - Thickness 0,25 mm a 3.2 mm - Dimensions |
| BS EN 2609-1989 | 铜锌合金的操纵缆索的转动圆套筒规范.尺寸和负荷 | Specification for turnbarrels, control cable in copper-zinc alloys - Dimensions and loads |
| BS EN 2617-2001 | 航空航天系列.钛和钛合金板材.厚度6mm< a> 100mm.尺寸 | Aerospace Series - Plates in titanium and titanium alloys - Thickness 6 mm a 100 mm - Dimensions |
| BS EN 2622-2001 | 航空航天系列.流体用耐热合金制的圆形管材.直径为3.2mm 100mm.尺寸 | Aerospace Series - Circular tubes, for fluids in heat resisting alloys - Diameter 3,2 mm D 100 mm - Dimensions |
| BS EN 2630-1994 | AL-P7009-T74511铝合金.对周边粗晶粒控制的a或D为125mm 挤压棒材和型材 | Aluminium alloy AL-P7009-T74511 - Extruded bars and sections a or D 125 mm with peripheral coarse grain control |
| BS EN 2632-2005 | 航空航天系列.铝合金AL-P7075.T73511.挤压棒材和型材.周边粗晶粒控制a或 D <= 150mm | Aerospace series - Aluminim alloy AL-P7075 - T73511 - Extruded bar and section - a or D <= 150 mm with peripheral coarse grain control |
| BS EN 2633-1994 | 铝合金AL-P2024-T3511.对周边粗晶粒控制的1,2 mm 或D≤150mm挤压棒材和型材. | Aluminium alloy AL-P2024-T3511 - Extruded bars and sections 1,2 mm a or D 150 mm with peripheral coarse grain control |
| BS EN 2635-2005 | 航空航天系列.铝合金AL-P2014A.T6511.挤压棒材和型材.a/D≤200mm周边粗粒控制 | Aerospace series - Aluminium alloy AL-P2014A - T6511 - Extruded bar and section - a or D <= 200 mm with peripheral coarse grain control |
| BS EN 2636-1994 | 铝合金AL-P6082-T6.对周边粗晶粒控制的挤压棒材和型材.a或D≤200mm, | Aluminium alloy AL-P6082-T6 - Extruded bars and sections a or D 200 mm with peripheral coarse grain control |
| BS EN 2648-1995 | 镀镉合金钢凹形垫圈 | Washers, concave, in alloy steel, cadmium plated |
| BS EN 2649-1995 | 镀镉合金钢螺纹至螺钉头的带槽盘头螺钉.等级:900MPa(室温)/235℃ | Screws, pan head, slotted, threaded to head, in alloy steel, cadmium plated - Classification - 900 MPa (at ambient temperature)/235 °C |
| BS EN 26501-1992 | 铁镍合金.规范和交货要求 | Ferronickel - Specification and delivery requirements |
| BS EN 2652-1997 | 镀镉合金钢制头部加螺纹的100°标准埋头开槽螺钉.等级:900MPa(室温)/235℃ | Screws, 100 ° countersunk normal head, slotted, threaded to head, in alloy steel, cadmium plated - Classification: 900 MPa (at ambient temperature)/235 °C |
| BS EN 2680-2006 | 航空航天系列.MoS2润滑镉镀层铝合金双耳游动自调自锁托板螺母.等级:900MPa(室温)/235℃ | Nuts, anchor, self-locking, floating, self-aligning, two lug, in alloy steel, cadmium plated, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 235 °C |
| BS EN 2681-2005 | 航空航天系列.铝合金AL-P7010-T74.手锻和模锻.a150 mm | Aerospace series - Aluminium alloy AL-P7010-T74 - Hand and die forgings - a 150 mm |
| BS EN 2684-2005 | 航空航天系列.铝合金AL-P7010-T7651.板材.6mma140mm | Aerospace series - Aluminium alloy AL-P7010-T7651 - Plate - 6 mm a 140 mm |
| BS EN 2687-2005 | 航空航天系列.铝合金AL-P7010-T7451.板材.6mma160mm | Aerospace series - Aluminium alloy AL-P7010-T7451 - Plate - 6 mm a 160 mm |
| BS EN 2693-2005 | 航空航天系列.AL-P5086-H111铝合金.0.3mm≤a≤6mm 薄板和带材 | Aerospace series - Aluminium alloy AL-P5086-H111 - Sheet and strip . 0,3 mm a 6 mm |
| BS EN 2694-2005 | 航空航天系列.AL-P6061-T6或T62铝合金.0.4mm≤a≤6mm 薄板和带材 | Aerospace series - Aluminium alloy AL-P6061-T6 or T62 - Sheet and strip - 0,4 mm a 6 mm |
| BS EN 2695-2005 | 航空航天系列.AL-P6081-T6铝合金.0.3mm≤a≤6mm薄板和带材 | Aerospace series - Aluminium alloy AL-P6081-T6 - Sheet and strip . 0,3 mm a 6 mm |
| BS EN 2696-2005 | 航空航天系列.AL-P7075-T6或T62铝合金.0.4mm≤a≤6mm 薄板和带材 | Aerospace series - Aluminium alloy AL-P7075-T6 or T62 - Sheet and strip - 0,4 mm a 6 mm |
| BS EN 2702-2005 | 航空航天系列.铝合金.AL-P6061.T6或T62.拉拔或挤压棒材和型材.a/D≤200mm | Aerospace series - Aluminium alloy - AL-P6061 - T6 or T62 - Drawn or extruded bar and section - a or D <= 200 mm |
| BS EN 2703-2005 | 铝合金AL-P2024-T4或T42.覆层薄板和带材.0.3 mm≤a≤6 mm | Aluminium alloy AL-P2024-T4 or T42 - Clad sheet and strip - 0,3 mm a 6 mm |
| BS EN 2731-2005 | 航空航天系列.镁合金钢MG-C46001 - T6.砂型铸造 | Aerospace series - Magnesium alloy MG-C46001 - T6 - Sand casting |
| BS EN 2732-2005 | 镁合金MG-C46001-T6.冷型铸造 | Magnesium alloy MG-C46001-T6 - Chill casting |
| BS EN 2753-1996 | 二硫化钼润滑的镀镉合金钢的承窝安装的单耳固定自锁托板螺母.等级:1100MPa(室温)/235℃ | Nuts, anchor, self-locking, fixed, single lug, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated - Classification - 1100 MPa (at ambient temperature) / 235 °C |
| BS EN 27627-1-1993 | 硬质合金.火焰原子吸收光谱法化学分析.第1部分:一般要求 | Hardmetals - Chemical analysis by flame atomic absorption spectrometry - General requirements |
| BS EN 27627-3-1993 | 硬质合金.用火焰原子吸收光谱法进行化学分析.0.01-0.5%(m/m)含量中钴、铁、锰和镍的测定 | Hardmetals - Chemical analysis by flame atomic absorption spectrometry - Determination of cobalt, iron, manganese and nickel in contents from 0,01 to 0,5 % (m/m) |
| BS EN 27627-4-1993 | 硬质合金.用火焰原子吸收光谱法进行化学分析.0.01-0.5%(m/m)含量中钼、钛和钒的测定 | Hardmetals - Chemical analysis by flame atomic absorption spectrometry - Determination of molybdenum, titanium and vanadium in contents from 0,01 to 0,5 % (m/m) |
| BS EN 27627-5-1993 | 硬质合金.用火焰原子吸收光谱法进行化学分析.0.5-2%(m/m)含量中钴、铁、锰、钼、镍、钛和钒的测定 | Hardmetals - Chemical analysis by flame atomic absorption spectrometry - Determination of cobalt, iron, manganese, molybdenum, nickel, titanium and vanadium in contents from 0,5 to 2 % (m/m) |
| BS EN 27787-3-1992 | 牙科用旋转器械规范.切割刀具.第3部分:铣床用硬质合金实验室刀具 | Specification for dental rotary instruments - Cutters - Carbide laboratory cutters for milling machines |
| BS EN 2802-2005 | 铝合金AL-P7475-T761.薄板和带材.0.6 mm≤a≤6 mm | Aluminium alloy AL-P7475-T761 - Sheet and strip - 0,6 mm a 6 mm |
| BS EN 2803-2005 | 航空航天系列.铝合金AL-P7475-T761.覆层薄板和带材.1.0 mm≤a≤6 mm | Aerospace series - Aluminium alloy AL-P7475-T761 - Clad sheet and strip - 1,0 mm a 6 mm |
| BS EN 2808-1997 | 钛和钛合金阳极氧化处理 | Anodizing of titanium and titanium alloys |
| BS EN 2858-1-1994 | 钛和钛合金坯料和锻件技术规范.第1部分:一般要求 | Titanium and titanium alloys - Forging stock and forgings - Technical specifications - General requirements |
| BS EN 2858-2-1994 | 钛和钛合金坯料和锻件技术规范.第2部分:锻坯 | Titanium and titanium alloys - Forging stock and forgings - Technical specification - Forging stock |
| BS EN 2858-3-1994 | 钛和钛合金坯料和锻件技术规范.第3部分:预行生产锻件和生产锻件 | Titanium and titanium alloys - Forging stock and forgings - Technical specifications - Pre-production and production forgings |
| BS EN 2859-2006 | 航空航天系列.镀镉合金钢短螺纹紧公差标准螺杆标准六角头螺栓.等级:1100MPa(室温)/235℃ | Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in alloy steel, cadmium plated - Classification: 1100 MPa (at ambient temperature) / 235 °C |
| BS EN 286-4-1995 | 装空气或氮气用的不点火加热的一般压力容器.第4部分:用于铁路运输车辆空气制动和辅助气动设备的铝合金压力 | Simple unfired pressure vessels designed to contain air or nitrogen - Aluminium alloy pressure vessels designed for air braking equipment and auxiliary pneumatic equipment for railway rolling stock |
| BS EN 28654-1993 | 金合金的颜色.定义、颜色范围和命名 | Colours of gold alloys - Definition, range of colours and designation |
| BS EN 2870-1996 | 二硫化钼润滑的阳极化的钛合金短螺纹紧公差标准螺杆标准双六角头螺栓.等级:1100MPa(室温)/315℃ | Bolts, normal bihexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature) /315 °C |
| BS EN 2874-1996 | 钝化处理的耐热镍基合金中长度螺纹紧公差标准螺杆的大双六角头螺栓.等级:1550MPa(室温)/315℃ | Bolts, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated - Classification: 1550 MPa (at ambient temperature) /315 °C |
| BS EN 2884-1996 | 二硫化钼润滑的阳极化钛合金短螺纹大公差标准螺杆斜十字槽盘头螺钉.等级:1100MPa(室温)/315℃ | Screws, pan head, offset cruciform recess, coarse tolerance normal shank, short thread, in titanium alloy, anodized MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 2885-1996 | 镀镉合金钢制短螺纹大公差标准螺杆斜十字槽盘头螺钉.等级:900MPa(室温)/235℃ | Screws, pan head, offset cruciform recess, coarse tolerance normal shank, short thread, in alloy steel, cadmium plated - Classification: 900 MPa (at ambient temperature)/235 °C |
| BS EN 2886-1996 | 镀镉的合金钢制短螺纹紧公差标准螺杆斜十字槽盘头螺钉.等级:900MPa(室温)/235℃ | Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in alloy steel, cadmium plated - Classification - 900 MPa (at ambient temperature)/235 °C |
| BS EN 2897-1996 | 镀镉的合金钢短螺纹紧公差标准螺杆斜十字槽盘头螺钉.等级:1100MPa(室温)/235℃ | Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in alloy steel, cadmium plated - Classification: 1100 MPa (at ambient temperature) /235 °C |
| BS EN 2912-1996 | 经阳极化或铬酸钝化处理的铝合金大直径扁平垫圈 | Washers, flat, large diameter, in aluminium alloy, anodized or chromated |
| BS EN 29202-1993 | 珠宝.贵重金属合金纯度 | Jewellery - Fineness of precious metal alloys |
| BS EN 2927-1996 | NI-P100HT(铬镍铁合金 718)耐热镍基合金长螺纹减荷螺杆双六角头螺栓.等级:1275MPa(室温)/650℃ | Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718) - Classification:1275 MPa (at ambient temperature)/650 °C |
| BS EN 2928-1996 | 镀银的NI-P100HT(铬镍铁合金 718)耐热镍基合金长螺纹减荷螺杆的双六角头螺栓.等级:1275MPa(室温)/650℃ | Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718), silver plated - Classification: 1275 MPa (at ambient temperature)/650 °C |
| BS EN 2929-1996 | NI-P101HT(Waspaloy)型耐热镍基合金制长螺纹安全柄十二角头螺栓.等级:1210MPa(室温)/730℃ | Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy) - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 2930-1996 | 镀银的NI-P101HT(沃斯帕洛尹)耐热镍基合金长螺纹减荷螺杆的双六角头螺栓.等级:1210MPa(室温)/730℃ | Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy), silver plated - Classification:1210 MPa (at ambient temperature)/730 °C |
| BS EN 2933-1996 | NI-P100HT(铬镍铁合金 718)耐热镍基合金长螺纹减荷螺杆的T型头螺栓.等级:1275MPa(室温)/650℃ | Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718) - Classification:1275 MPa (at ambient temperature)/650 °C |
| BS EN 2934-1996 | 镀银的NI-P100HT(铬镍铁合金 718)耐热镍基合金长螺纹减荷螺杆的T型头螺栓.等级:1275MPa(室温)/650℃ | Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718), silver plated - Classification:1275 MPa (at ambient temperature)/650 °C |
| BS EN 2935-1996 | NI-P101HT(沃斯帕洛尹)耐热镍基合金长螺纹减荷螺杆的T型头螺栓.等级:1210MPa(室温)/730℃ | Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy) - Classification:1210 MPa (at ambient temperature)/730 °C |
| BS EN 2936-1996 | 镀银的NI-P101HT(沃斯帕洛尹)耐热镍基合金长螺纹减荷螺杆的T型头螺栓.等级:1210MPa(室温)/730℃ | Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy), silver plated - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 2942-1998 | 镀银耐热镍基合金NI-PH2801(因康镍合金X750)自锁紧螺旋形线圈螺纹插入件 | Inserts, screw thread, helical coil, self-locking, in heat resisting nickel base alloy NI-PH2801 (Inconel X750), silver plated |
| BS EN 2955-1993 | 钛和钛合金废料的回收利用 | Recycling of titanium and titanium alloy scrap |
| BS EN 3005-2005 | 航空航天系列.自锁紧、MJ螺纹、NI-PH1302耐热镍基合金(沃斯帕洛尹合金)制镀银或不镀银螺母.等级:1210MPa ( | Aerospace series - Nuts, self-locking, MJ threads, in heat resisting nickel base alloy NI-PH1302 (Waspaloy), silver plated or uncoated - Classification: 1210 MPa (at ambient temperature) / 730 °C - Technical specification |
| BS EN 3008-1998 | 耐热镍基合金NI-P100HT(铬镍铁合金718)制薄柄长螺纹六角头螺栓.等级:1275 MPa(室温)/650℃ | Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718) - Classification:1275 MPa (at ambient temperature)/650 °C |
| BS EN 3009-1998 | 镀银耐热镍基合金NI-P100HT(铬镍铁合金718)制薄柄长螺纹六角头螺栓.等级:1275 MPa(室温)/650℃ | Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718), silver plated - Classification - 1275 MPa (at ambient temperature)/650 °C |
| BS EN 3010-1998 | 耐热镍基合金NI-P101HT(沃斯帕洛尹合金)薄柄长螺纹六角头螺栓.等级:1210 MPa(室温)/730℃ | Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy) - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 3011-1998 | 镀银耐热镍基合金NI-P101HT(沃斯帕洛尹合金)薄柄长螺纹六角头螺栓.等级:1210 MPa(室温)/730℃ | Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy), silver plated - Classification:1210 MPa (at ambient temperature)/730 °C |
| BS EN 3012-1996 | 耐热镍基合金HI-P101HT(沃斯帕洛尹合金)双六角头自锁螺母.等级:1210 MPa(室温)/730℃ | Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-P101HT (Waspaloy) - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 3013-1996 | 镀银的耐热镍基合金HI-P101HT(沃斯帕洛尹合金)双六角头自锁螺母.等级:1210 MPa(室温)/730℃ | Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-P101HT (Waspaloy), silver plated - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 3035-1997 | 镀镉的合金钢短螺纹紧公差标准螺杆斜十字槽100°标准埋头螺钉.等级:1100 MPa(室温)/235℃ | Screws, 100 ° countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in alloy steel, cadmium plated - Classification: 1100 MPa (at ambient temperature)/235 °C |
| BS EN 3037-1997 | 二硫化钼润滑的阳极化的钛合金短螺纹紧公差标准螺杆斜十字槽盘头螺钉.等级:1100 MPa(室温)/315℃ | Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3063-1994 | 耐热镍基合金NI-P101HT(沃斯帕洛尹合金)制的中长度螺纹紧公差螺杆双六角头螺栓.等级:1210 MPa(室温)/730℃ | Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy) - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 3080-2006 | 钛合金8°30'管连接件.带止推金属丝螺母的缩短三通 | Aerospace series - Pipe coupling 8°30' in titanium alloy - Tees, reduced, branch with thrust wire nut |
| BS EN 3081-2001 | 航空航天系列.钛合金管连接件8°30'.带动梁密封端头的修理用焊接箍 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Ferrules welded, with dynamic beam seal end, for repair |
| BS EN 3082-2001 | 航空航天系列.钛合金管连接件8°30'.修理用闷头焊接活接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead welded, for repair |
| BS EN 3083-2001 | 航空航天系列.钛合金管连接件8°30'.修理用闷头长焊接端头活接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead, long welded end, for repair |
| BS EN 3084-2001 | 航空航天系列.钛合金管连接件8°30'.修理用焊接端头螺纹活接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, welded end threaded for repair |
| BS EN 3112-1995 | 镀镉的合金钢的螺纹至螺栓头的标准六角头螺栓.等级:900 MPa(室温)/235℃ | Bolts, normal hexagonal head, threaded to head, in alloy steel, cadmium plated - Classification: 900 MPa (at ambient temperature)/235 °C |
| BS EN 3114-001-2006 | 航空航天系列.试验方法.(α+β)钛合金锻制品的微观结构.第001部分:一般要求 | Aerospace series - Test method - Microstructure of (α + β) titanium alloy wrought products - Part 001: General requirements |
| BS EN 3114-002-2007 | 航空航天系列.试验方法.钛合金锻制品微观结构(α+ β).棒材、型材、锻坯和锻件微观结构 | Aerospace series - Test method - Microstructure of ( + ) titanium alloy wrought products - Microstructure of bars, sections, forging stock and forgings |
| BS EN 3114-003-2006 | 航空航天系列.试验方法.(α+β)钛合金锻制品的微观结构.第003部分:板材的微观结构 | Aerospace series - Test method - Microstructure of (α + β) titanium alloy wrought products - Part 003: Microstructure of plate |
| BS EN 3114-004-2006 | 航空航天系列.试验方法.(α+β)钛合金锻制品的微观结构.第004部分:超塑性成型薄板微观结构 | Aerospace series - Test method - Microstructure of (α + β) titanium alloy wrought products - Part 004: Microstructure of sheet for superplastic forming |
| BS EN 3141-1996 | 耐高温镍基合金NI-P11镀镉通用头实心铆钉.英制系列 | Rivets, solid, universal head, in heat resisting nickel base alloy NI-P11, cadmium plated, inch based series |
| BS EN 3142-1996 | 耐高温镍基合金NI-P11通用头实心铆钉.英制系列 | Rivets, solid, universal head, in heat resisting nickel base alloy NI-P11, inch based series |
| BS EN 31427-1994 | 银珠宝合金中银含量测定.溴化钾容量(电位)法 | Determination of silver in silver jewellery alloys - Volumetric (potentiometric) method using potassium bromide |
| BS EN 3150-1995 | 耐热镍基NI-P100HT(因康718)型合金肩部无头轴销 | Pins, shoulder, headless, in heat resisting nickel base alloy NI-P100HT (Inconel 718) |
| BS EN 3151-1995 | 耐热镍基合金NI-P100HI(因康718)无槽圆柱销 | Dowels, plain, in heat resisting nickel base alloy NI-P100HT (Inconel 718) |
| BS EN 3236-1998 | 内螺纹镀银耐热镍基合金NI-P100HT(因康镍合金718)薄壁、自锁紧、短式插入件 | Inserts, thin wall, self-locking, short, in heat resisting nickel base alloy NI-P100HT (Inconel 718), silver plated internal thread |
| BS EN 3237-1998 | 内螺纹镀银耐热镍基合金NI-P100HT(因康镍合金718)薄壁、自锁紧、长式插入件 | Inserts, thin wall, self-locking, long, in heat resisting nickel base alloy NI-P100HT (Inconel 718), silver plated internal thread |
| BS EN 3239-1996 | HI-P101HT型耐热镍基合金(沃斯帕洛尹合金)制螺纹镀银的自锁十二角头螺母.等级:1210 MPa(室温)/730℃型 | Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-P101HT (Waspaloy), silver plated thread - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 3243-2001 | 航空航天系列.钛合金8°30'管连接件.带动力横梁密封端头的焊接环箍 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Ferrule, welded, with dynamic beam seal end |
| BS EN 3244-2001 | 航空航天系列.钛合金8°30’管连接件.双端头的活接头 | Aerospace Series - Pipe coupling 8 °30' in titanium alloy - Unions, double ended |
| BS EN 3245-2001 | 航空航天系列.钛合金8°30'管连接件.变径活接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, reducer |
| BS EN 3246-2001 | 航空航天系列.钛合金8°30' 管连接件.、闷头活接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead |
| BS EN 3247-2001 | 航空航天系列.钛合金8°30'管连接件.闷头焊接端活接头、 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead welded end |
| BS EN 3248-2001 | 航空航天系列.钛合金管连接件8°30’.带锁紧装置的缩径管端的转接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Adaptors, reduced pipe end, with lockring |
| BS EN 3264-2001 | 航空航天系列.钛合金8°30管连接件’.止推金属丝螺母 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Thrust wire nut |
| BS EN 3266-2001 | 航空航天系列.钛合金管连接件.闷头螺母 | Aerospace series - Pipe coupling in titanium alloy - Bulkhead nut |
| BS EN 3267-2001 | 航空航天系列.钛合金闷头垫圈 | Aerospace series - Washers, bulkhead in titanium alloy |
| BS EN 3268-2001 | 航空航天系列.钛合金8°30'管连接件.压力管塞 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Pressure plug |
| BS EN 3269-2001 | 航空航天系列.钛合金管连接件8°30'.带动梁密封端头的暗箍 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Ferrules, blind, with dynamic beam seal end |
| BS EN 3270-2001 | 航空航天系列.8°30'钛合金管连接件.带锁紧环的截止管塞 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Blanking plug with lockring |
| BS EN 3272-2001 | 航空航天系列.8°30'钛合金管连接件.动态横梁密封端头的焊接箍.几何配置 | Aerospace series - Pipe coupling 8 °30' - Dynamic beam seal end for ferrule, welded - Geometric configuration |
| BS EN 3273-2001 | 航空航天系列.钛合金管连接件8°30'.弯头、十字管和三通管用动梁密封端头.几何配置 | Aerospace series - Pipe coupling 8 °30' - Dynamic beam seal end for elbows, tees and crosses - Geometric configuration |
| BS EN 3297-1998 | 薄壁、自锁紧、耐热镍基合金NI-P100HT(铬镍铁合金718)、MJ螺纹嵌镶件.技术规范 | Inserts, thin wall, self-locking, MJ threads, in heat resisting nickel base alloy NI-P100HT (Inconel 718) - Technical specification |
| BS EN 3303-1997 | 镀镉合金钢制中长螺纹粗公差标准柄六角凹帽罩头螺钉.等级:1100 MPa(室温)/235℃ | Screws, cap head, hexagon socket, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated - Classification: 1100 MPa (at ambient temperature)/235 °C |
| BS EN 3304-1997 | 二硫化钼润滑的阳极化的钛合金短螺纹紧公差标准螺杆斜十字槽100°小埋头螺钉.等级:1100 MPa(室温)/315℃ | Screws, 100 ° countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3305-1997 | 镀镉的合金钢短螺纹紧公差标准螺杆斜十字槽100°小埋头螺钉.等级:1100 MPa(室温)/235℃ | Screws, 100 ° countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in alloy steel, cadmium plated - Classification: 1100 MPa (at ambient temperature)/235 °C |
| BS EN 3306-1996 | 二硫化钼润滑的阳极化的钛合金螺纹至螺钉头部的斜十字槽100°标准埋头螺钉.等级:1100 MPa(室温)/315℃ | Screws, 100 ° countersunk normal head, offset cruciform recess, threaded to head, in titanium alloy, anodized, MoS2 lubricated - Classification - 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3307-1997 | 二硫化钼润滑的阳极化的钛合金螺纹至螺钉头部的斜十字槽盘头螺钉.等级:1100 MPa(室温)/315℃ | Screws, pan head, offset cruciform recess, threaded to head, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3308-1996 | 二硫化钼润滑的阳极化的钛合金螺纹至螺钉头部的标准六角头螺钉.等级:1100 MPa(室温)/315℃ | Screws, normal hexagonal head, threaded to head, in titanium alloy, anodized, MoS2 lubricated - Classification - 1100 MPa (at ambient temperature) /315 °C |
| BS EN 3332-2005 | 航空航天系列.AL-P7475-T762型铝合金.覆层铝合金薄板材和带材.1.0mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P7475-T762 - Clad sheet and strip - 1,0 mm a 6 mm |
| BS EN 3333-2005 | 铝合金AL-P7475-T762.薄板和带材.0.6 mm≤a≤6 mm | Aluminium alloy AL-P7475-T762 - Sheet and strip - 0,6 mm a 6 mm |
| BS EN 3335-2005 | 铝合金AL-P7475-O2.超塑性成型用薄板(SPF).0.8 mm≤a≤6 mm | Aluminium alloy AL-P7475-O2 - Sheet for superplastic forming (SPF) - 0,8 mm a 6 mm |
| BS EN 3338-2005 | 航空航天系列.AL-P7050型铝合金.T74511.挤压棒材和型材.a或D<= 150 mm周边粗粒控制 | Aerospace series - Aluminim alloy AL-P7050 - T74511 - Extruded bar and section - a or D <= 150 mm with peripheral coarse grain control |
| BS EN 3339-2006 | 航空航天系列.AL-P7010-T76型铝合金.压模锻件.a ≤200mm | Aerospace series — Aluminium alloy AL-P7010- — T76 — Die forgings — a u 200 mm |
| BS EN 3341-2005 | 铝合金AL-P6061-T4或T42.薄板和带材.0.4 mm≤a≤6 mm | Aluminium alloy AL-P6061-T4 or T42 - Sheet and strip - 0,4 mm a 6 mm |
| BS EN 3342-2005 | 航空航天系列.AL-P6061型铝合金.T4或T42.拉拔或挤压棒材和型材.a或D <= 150 mm | Aerospace series - Aluminim alloy AL-P6061 - T4 or T42 - Drawn or extruded bar and section - a or D <= 150 mm |
| BS EN 3344-2005 | 航空航天系列.AL-P7050型铝合金.T76511.挤压棒材和型材.a或D<= 150 mm周边粗粒控制 | Aerospace series - Aluminim alloy AL-P7050 - T76511 - Extruded bar and section - a or D <= 150 mm with peripheral coarse grain control |
| BS EN 3347-2005 | 航空航天系列.铝合金AL-P2024.T8511.挤压棒材和型材.a/D≤150mm周边粗粒控制 | Aerospace series - Aluminim alloy AL-P2024 - T8511 - Extruded bar and section - a or D <= 150 mm with peripheral coarse grain control |
| BS EN 3379-1996 | 镀银的NI-P101HT(沃斯帕洛尹)耐热镍基合金中长度螺纹紧公差螺杆的双六角头螺栓.等级:1210 MPa(室温)/730℃ | Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy), for increased height nuts - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 3444-2006 | 航空航天系列.钝化镍合金制耐热、标准柄、紧公差中长螺纹大直径十二沉头螺栓.等级:1250MPa(室温)/650℃ | Aerospace series - Bolt, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated - Classification: 1250 MPa (at ambient temperature) / 650 ℃ |
| BS EN 3474-2005 | 航空航天系列.AL-P2024-T81型铝合金.薄板材和带材.0.25 mm <= a <= 6 mm | Aerospace series - Aluminium alloy AL-P2024-T81 - Sheet and strip - 0,25 mm <= a <= 6 mm |
| BS EN 3506-2001 | 航空航天系列.耐热合金制成的热轧薄板和板材.厚度2.0mm a 100mm.尺寸 | Aerospace series - Hot rolled sheets and plates in heat resisting alloys - Thickness 2,0 mm a 100 mm - Dimensions |
| BS EN 3542-1998 | 耐热镍基合金NI-PH2801(因康镍合金X750)自锁紧螺旋形线圈螺纹插入件 | Inserts, screw thread, helical coil, self-locking, in heat resisting nickel base alloy NI-PH2801 (Inconel X750) |
| BS EN 3552-2005 | 铝合金AL-P2618A-T6或T62.覆层薄板和带材.0.4 mm≤a≤6 mm | Aerospace series - Aluminium alloy AL-P2618A-T6 or T62 - Clad sheet and strip - 0,4 mm a 6 mm |
| BS EN 3553-2005 | 航空航天系列.铝合金AL-P2618A-T6511.挤制棒材和型材.a或D160mm | Aerospace series - Aluminium alloy AL-P2618A-T6511 - Extruded bar and section - a or D 160 mm |
| BS EN 3561-2001 | 航空航天系列.钛合金管连接件8°30'.在管端焊接和变径的带动力横梁密封端头的环箍 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Ferrules with dynamic beam seal end, welded and reduced at pipe end |
| BS EN 3566-2001 | 航空航天系列.钛合金8°30'管连接件.带锁紧装置的转接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Adaptor with lockring |
| BS EN 3638-2007 | 航空航天系列.FE-PA2601(X6NiCrTiMoV26-15)耐热合金.自耗电极再熔炼.固溶和沉淀处理.薄板材、带材和厚板材. | Aerospace series - Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) - Consumable electrode remelted - Solution and precipitation treated - Sheet, strip and plate - 0,5 mm a 10 mm |
| BS EN 3665-1997 | 清漆和涂料检验方法.铝合金耐纤维状腐蚀检验 | Test methods for paints and varnishes - Filiform corrosion resistance test on aluminium alloys |
| BS EN 3668-2006 | 航空航天系列.NI-PH2301(NiCr21Fe18Mo9)型耐热合金.非热处理的.锻坯.a或D≤250mm | Aerospace series - Heat resisting alloy NI-PH2301 (NiCr21Fe18Mo9) - Non heat treated - Forging stock - a or D ≤ 250 mm |
| BS EN 3671-2007 | 航空航天系列.NI-PH3601(NiCr22Mo9Nb)型耐热合金.非热处理.锻坯.a或D≤250mm | Aerospace series - Heat resisting alloy NI-PH3601 (NiCr22Mo9Nb) - Non heat treated - Forging stock - a or D 250 mm |
| BS EN 3683-2007 | 航空航天系列.试验方法.钛合金锻造产品.基本(α)含量测定.点数法和线截取法 | Aerospace series - Test methods - Titanium alloy wrought products - Determination of primary content - Point count method and line intercept method |
| BS EN 3684-2007 | 航空航天系列.试验方法.钛合金锻造制品.β转变温度的测定.金相法 | Aerospace series - Test methods - Titanium alloy wrought products - Determination of transus temperature - Metallographic method |
| BS EN 3688-2001 | 航空航天系列.焊接管用钛合金制T环形填充物.14000kPa公称压力 | Aerospace series - T-ring fillers in titanium alloy for welded pipes - 14000 kPa nominal pressure |
| BS EN 3689-2001 | 航空航天系列.焊接管用钛合金制T环形填充物.28000kPa公称压力 | Aerospace series - T-ring fillers in titanium alloy for welding pipes - 28000 kPa nominal pressure |
| BS EN 3690-2001 | 航空航天系列.钛合金8°30'管联接件.长闷头活接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead, long |
| BS EN 3691-2001 | 航空航天系列.钛合金8°30'管连接件.长焊接的闷头活接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, bulkhead, long welded |
| BS EN 3719-2005 | 航空航天系列.电缆的铝或铝合金导体.产品标准 | Aluminium or aluminium alloy conductors for electrical cables — Product standard |
| BS EN 3724-2004 | 细杆长螺纹双六角头镀MoS2的钛合金TI-P64001螺栓.强度等级:1100MPa(室温) | Bolts, double hexagon head, relieved shank, long thread, in titanium alloy TI-P64001, MoS2 coated - Strength class: 1100 MPa (at ambient temperature) |
| BS EN 3725-2005 | 航空航天系列.阳极氧化、MoS2涂覆的钛合金TI-P64001制长螺纹、标准杆、六瓣凹槽盘头螺钉.强度等级:1100MPa( | Aerospace series - Screws, pan head, six lobe recess, normal shank, long thread, in titanium alloy TI-P64001, anodized, MoS2 coated - Strength class: 1100 MPa (at ambient temperature) |
| BS EN 3730-2001 | 航空航天系列..鞍座形夹子.带橡胶弹性垫料的铝合金的固定式滑动型.尺寸.质量 | Aerospace series - Clamps, saddle - Fixed and sliding version in aluminium alloy with rubber cushioning - Dimensions - Masses |
| BS EN 3740-1997 | 二硫化钼润滑的阳极化的钛合金短螺纹紧公差螺杆薄六角头带肩螺栓.等级:1100 MPa(室温)/315℃ | Bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3769-1997 | 耐腐蚀钢和耐高温合金的电解抛光 | Electrolytic polishing of corrosion resisting steels and heat resisting alloys |
| BS EN 3818-2005 | 航空航天系列.MJ螺纹的钛合金TI-P64001螺栓.强度等级:1100MPa(室温).技术规范 | Aerospace series - Bolts, MJ threads, in titanium alloy TI-P64001 - Strength class: 1100 MPa (at ambient temperature) - Technical specification |
| BS EN 3832-2005 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金718)制长螺纹、细杆、十二角螺栓.等级:1550MPa(室温)/650℃ | Aerospace series - Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification: 1550 MPa (at ambient temperature) / 650 °C |
| BS EN 3833-2005 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金718)制MJ螺纹螺栓.等级:1550MPa(室温)/650℃.技术规范 | Aerospace series - Bolts, MJ threads, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), passivated - Classification: 1550 MPa (at ambient temperature) / 650 °C - Technical specification |
| BS EN 3851-2003 | 航空航天系列.TI-P64001型钛合金制60 球面管联接器.直的回转螺帽 | Aerospace series - Pipe couplings, 60 °, spherical, in titanium alloy TI-P64001 - Swivel nuts, straight |
| BS EN 3852-2002 | 航空航天系列.TI-P64001型钛合金制、球形、60度管连接器.直螺纹式焊接接头 | Aerospace series - Pipe couplings, 60 °, spherical, in titanium alloy TI-P64001 - Straight unions, welded, threaded |
| BS EN 3853-2002 | 航空航天系列.TI-P64001型钛合金制、球形、60度管连接器.直活螺纹接头 | Aerospace series - Pipe couplings, 60 °, spherical, in titanium alloy TI-P64001 - Straight unions, threaded |
| BS EN 3854-2002 | 航空航天系列.TI-P64001型钛合金制、球形、60度管连接器.焊接箍 | Aerospace series - Pipe couplings, 60 °, spherical, in titanium alloy TI-P64001 - Ferrules, welded |
| BS EN 3855-2002 | 航空航天系列.TI64001型钛合金制、球形、60度管连接器.盖 | Aerospace series - Pipe couplings, 60 ° spherical, in titanium alloy TI-P64001 - Caps |
| BS EN 3856-2002 | 航空航天系列.TI-P64001型钛合金制、球形、60度管连接器.止推金属线用转动螺母 | Pipe couplings, 60 °, spherical, in titanium alloy TI-P64001 - Swivel nuts for thrust wire |
| BS EN 3857-2002 | 航空航天系列.TI-P64001型钛合金制、球形、60度管连接器.焊接90度弯头 | Aerospace series - Pipe couplings, 60 °, spherical, in titanium alloy TI-P64001 - Elbows 90 °, welded |
| BS EN 3858-2002 | 航空航天系列.TI-P64001型钛合金制、球形、60度管连接器.FE-PA 13刑止推钢丝 | Aerospace series - Pipe couplings, 60 °, spherical, in titanium alloy TI-P64001 - Thrust wires in steel FE-PA 13 |
| BS EN 3867-2005 | 航空航天系列.管连接件、松套法兰和密封件.钛合金TI-P64001法兰 | Aerospace series - Pipe couplings, loose flanges and seals - Flanges in titanium alloy TI-P64001 |
| BS EN 3868-2005 | 航空航天系列.管连接件、松套法兰和密封件.钛合金TI-P64001焊接法兰连接件 | Aerospace series - Pipe couplings, loose flanges and seals - Flange connectors, welded, in titanium alloy TI-P64001 |
| BS EN 3869-2004 | 航空航天系列.管连接件、松套法兰和密封件.碳氟化合物橡胶密封件和铝合金保护壳 | Aerospace series - Pipe couplings, loose flanges and seals - Seals in fluorocarbon rubber and armature in aluminium alloy |
| BS EN 3872-2005 | 航空航天系列.铝合金AL-R39002-H112.模锻件.a≤200 mm | Aerospace series - Aluminium alloy AL-R39002-H112 - Die forgings - a 200 mm |
| BS EN 3882-2001 | 航空航天系列.耐热合金NI-WH1801(NiCr20Co18Ti3Al2).焊接用填充金属丝 | Aerospace series - Heat resisting alloy NI-WH1801 (NiCr20Co18Ti3Al2) - Filler wire for welding |
| BS EN 3883-2001 | 航空航天系列.耐热合金NI-WH2301(NiCr22Fe19Mo9Co2).焊接用填充金属 | Aerospace series - Heat resisting alloy NI-WH2301 (NiCr22Fe19Mo9Co2) - Filler metal for welding |
| BS EN 3884-2001 | 航空航天系列.耐热合金NI-WH2601(NiCr19Nb5Mo3Ti).焊接用填充金属 | Aerospace series - Heat resisting alloy NI-WH2601 (NiCr19Nb5Mo3Ti) - Filler metal for welding |
| BS EN 3885-2001 | 航空航天系列.耐热合金NI-WH3601(NiCr22Mo9Nb4).焊接用填充金属 | Aerospace series - Heat resisting alloy NI-WH3601 (NiCr22Mo9Nb4) - Filler metal for welding |
| BS EN 3886-2001 | 航空航天系列.耐热合金NI-WH1303(NiCo20Cr20Mo5Ti2Al).焊接用填充金属 | Aerospace series - Heat resisting alloy NI-WH1303 (NiCo20Cr20Mo5Ti2Al) - Filler metal for welding |
| BS EN 3887-2001 | 航空航天系列.耐热合金钢CO-WH4101(CoCr20W15Ni).焊接填充金属 | Aerospace series - Heat resisting alloy CO-WH4101 (CoCr20W15Ni) - Filler metal for welding |
| BS EN 3888-2001 | 航空航天系列.耐热合金CO-WH1402(CoCr22Ni22W15).焊接用填充金属 | Aerospace series - Heat resisting alloy CO-WH1402 (CoCr22Ni22W15) - Filler metal for welding |
| BS EN 3892-2001 | 航空航天系列.钛合金TI-W64001.焊接填充金属 | Aerospace series - Titanium alloy TI-W64001 - Filler metal for welding |
| BS EN 3893-2001 | 航空航天系列.钛合金TI-W19001.焊接用填充金属 | Aerospace series - Titanium alloy TI-W19001 - Filler metal for welding |
| BS EN 3894-2001 | 航空航天系列.耐热合金NI-WD3201(NiMo25Fe6Cr5).焊接填充金属 | Aerospace series - Heat resisting alloy NI-WD3201 (NiMo25Fe6Cr5) - Filler metal for welding |
| BS EN 3895-2001 | 航空航天系列,耐热合金NI-WH3901(NiCr16Mo15).焊接填充金属 | Aerospace series - Heat resisting alloy NI-WH3901 (NiCr16Mo15) - Filler metal for welding |
| BS EN 3907-2004 | 航空航天系列.标准杆长螺纹双六角头镀MoS2的钛合金TI-P64001螺栓.等级:1100MPa(室温)/350 鳦 | Aerospace series - Bolts, double hexagon head, normal shank, long thread, in titanium alloy TI-P64001, MoS2 coated - Classification: 1100MPa (at ambient temperature)/350 °C |
| BS EN 3913-2007 | 航空航天系列.部件修复用内螺纹镀银、NI-PH2601(Ni-P100HT, Inconel 718)型耐热镍基合金、短自锁薄壁嵌镶件 | Aerospace series - Insert, thin wall, self-locking, short, in heat resisting nickel base alloy NI-PH2601 (Ni-P100HT, Inconel 718), silver plated on internal thread, for salvage of components |
| BS EN 3917-1998 | 镍基合金NI-B41201(NiCr14Si5B3C).铜焊用填充金属.粉末或糊料 | Nickel base alloy NI-B41201 (NiCr14Si5B3C) - Filler metal for brazing - Powder or paste |
| BS EN 3918-1998 | 镍基合金NI-B41201(NiCr14Si5B3C).铜焊用填充金属.窄条带材 | Nickel base alloy NI-B41201 (NiCr14Si5B3C) - Filler metal for brazing - Tape |
| BS EN 3919-1998 | 镍基合金NI-B41201(NiCr14Si5B3C).铜焊用填充金属.非晶形箔 | Nickel base alloy NI-B41202 (NiCr14Si5B3) - Filler metal for brazing - Amorphous foil |
| BS EN 3920-2001 | 航空航天系列.镍基合金 Ni-B41202.硬钎焊填充金属.粉末或膏体 | Aerospace series - Nickel base alloy NI-B41202 (NiCr14Fe5Si5B3) - Filler metal for brazing - Powder or paste |
| BS EN 3921-2001 | 航空航天系列.镍基合金 Ni-B41203.硬扦焊填充金属.非晶态箔 | Aerospace series - Nickel base alloy NI-B41203 (NiCr7Si5B3) - Filler metal for brazing - Amorphous foil |
| BS EN 3922-1998 | 镍基合金NI-B41203(NiCr7Si5B3).铜焊用填充金属.硼化物箔 | Nickel base alloy NI-B41203 (NiCr7Si5B3) - Filler metal for brazing - Borided foil |
| BS EN 3923-2001 | 航空航天系列.镍基合金Ni-B41203(NiCr7Si5B3Fe3).硬钎焊填充金属.粉末或糊料 | Aerospace series - Nickel base alloy NI - B41203 (NiCr7Si5B3Fe3) - Filler metal for brazing - Powder or paste |
| BS EN 3924-1998 | 镍基合金NI-B41203(NiCr7Si5B3).铜焊用填充金属.带材 | Nickel base alloy NI-B41203 (NiCr7Si5B3) - Filler metal for brazing - Tape |
| BS EN 3925-2001 | 航空航天系列.镍基合金NI-B40001(NiSi5B3).硬钎焊用填充金属.非晶形箔 | Aerospace series - Nickel base alloy NI-B40001 (NiSi5B3) - Filler metal for brazing - Amorphous foil |
| BS EN 3926-2001 | 航空航天系列.镍基合金NI-B40001(NiSi5B3).硬钎焊用填充金属.硼化物箔 | Aerospace series - Nickel base alloy NI-B40001 (NiSi5B3) - Filler metal for brazing - Borided foil |
| BS EN 3927-2001 | 航空航天系列.NI-B40001(NiSi5B3)镍基合金.硬钎焊用填充金属.粉末或糊料 | Aerospace series - Nickel base alloy NI-B40001 (NiSi5B3) - Filler metal for brazing - Powder or paste |
| BS EN 3928-1998 | 镍基合金NI-B40001(NiSi5B3).铜焊用填充金属.带材 | Nickel base alloy NI-B40001 (NiSi5B3) - Filler metal for brazing - Tape |
| BS EN 3930-2001 | 航空航天系列.镍基合金NI-B31001(NiCr19Si10).硬钎焊用填充金属.粉末或糊料 | Aerospace series - Nickel base alloy NI-B31001 (NiCr19Si10) - Filler metal for brazing - Powder or paste |
| BS EN 3931-1998 | 镍基合金NI-B31001(NiCr19Si10).铜焊用填充金属.带材 | Nickel base alloy NI-B31001 (NiCr19Si10) - Filler metal for brazing - Tape |
| BS EN 3932-2001 | 航空航天系列.镍基合金NI-B13001(NiP11).硬钎焊用填充金属.非晶形箔 | Aerospace series - Nickel base alloy NI-B13001 (NiP11) - Filler metal for brazing - Amorphous foil |
| BS EN 3933-2001 | 航空航天系列.镍基合金NI-B13001(NiP11).硬钎焊用填充金属.粉末或糊料 | Aerospace series - Nickel base alloy NI-B13001 (NiP11) - Filler metal for brazing - Powder or paste |
| BS EN 3934-2001 | 航空航天系列.镍基合金NI-B21001(NiCr15B4).硬钎焊用填充金属.非晶形箔 | Aerospace series - Nickel base alloy NI-B21001 (NiCr15B4) - Filler metal for brazing - Amorphous foil |
| BS EN 3935-2001 | 航空航天系列.镍基合金 Ni-B21001.硼化物箔 | Aerospace series - Nickel base alloy NI-B21001 (NiCr15B4) - Filler metal for brazing - Borided foil |
| BS EN 3936-2001 | 航空航天系列.镍基合金NI-B21001(NiCr15B4).硬钎焊用填充金属.粉末或糊料 | Aerospace series - Nickel base alloy NI-B21001 (NiCr15B4) - Filler metal for brazing - Powder or paste |
| BS EN 3937-2001 | 航空航天系列.镍基合金NI-B44101(NiW12Cr10Si4Fe3B3).硬钎焊用填充金属.粉末或糊料 | Aerospace series - Nickel base alloy NI-B44101 (NiW12Cr10Si4Fe3B3) - Filler metal for brazing - Powder or paste |
| BS EN 3938-2001 | 航空航天系列.镍基合金 Ni-B46001.非晶态箔 | Aerospace series - Nickel base alloy NI-B46001 (NiCo20Si5B3) Filler metal for brazing - Amorphous foil |
| BS EN 3939-2001 | 航空航天系列.镍基合金 Ni-B46001.硬钎焊填充金属.粉末或膏体 | Aerospace series - Nickel base alloy NI-B46001 (NiCo20Si5B3) - Filler metal for brazing - Powder or paste |
| BS EN 3940-1998 | 镍基合金NI-B46001(NiCo20Si5B3).铜焊用填充金属.带材 | Nickel base alloy NI-B46001 (NiCo20Si5B3) - Filler metal for brazing - Tape |
| BS EN 3941-2001 | 航空航天系列.镍基合金 Ni-B41204.硬钎焊填充金属.非晶态箔 | Aerospace series - Nickel base alloy NI-B41204 (NiCr13Si4B3) - Filler metal for brazing - Amorphous foil |
| BS EN 3942-2001 | 航空航天系列.镍基合金NI-B41204(NiCr13Si4B3).硬钎焊用填充金属.硼化物箔 | Aerospace series - Nickel base alloy NI-B41204 (NiCr13Si4B3) - Filler metal for brazing - Borided foil |
| BS EN 3943-2001 | 航空航天系列.镍基合金NI-B41204(NiCr13Si4B3).硬钎焊用填充金属.粉末或糊料 | Aerospace series - Nickel base alloy NI-B41204 (NiCr13Fe4Si4B3) - Filler metal for brazing - Powder or paste |
| BS EN 3944-1998 | 镍基合金NI-B41204(NiCr13Si4B3).铜焊用填充金属.带材 | Nickel base alloy NI-B41204 (NiCr13Si4B3) - Filler metal for brazing - Tape |
| BS EN 3945-2001 | 航空航天系列.镍基合金 Ni-B48801.硬钎焊填充金属.粉末或膏体 | Aerospace series - Nickel base alloy NI-B48801 (NiMn19Si6Cu4B) - Filler metal for brazing - Powder or paste |
| BS EN 3946-2001 | 航空航天系列.镍基合金 Ni-15701.硬钎焊填充金属.粉末或膏体 | Aerospace series - Nickel base alloy NI-B15701 (NiPd34Au30) - Filler metal for brazing - Powder or paste |
| BS EN 3947-1998 | 镍基合金NI-B15701(NiPd34Au30).铜焊用填充金属.轧制箔 | Nickel base alloy NI-B15701 (NiPd34Au30) - Filler metal for brazing - Rolled foil |
| BS EN 3948-1998 | 镍基合金NI-B15701(NiPd34Au30).铜焊用填充金属.线材 | Nickel base alloy NI-B15701 (NiPd34Au30) - Filler metal for brazing - Wire |
| BS EN 3952-2001 | 航空航天系列.银基合金AG-B10001(AgCu28).硬钎焊用填充金属.金属丝 | Aerospace series - Silver base alloy AG-B10001 (AgCu28) - Filler metal for brazing - Wire |
| BS EN 3953-2001 | 航空航天系列.银基合金AG-B12401(AgCu40Zn5Ni).硬钎焊用填充金属.金属丝 | Aerospace series - Silver base alloy AG-B12401 (AgCu40Zn5Ni) - Filler metal for brazing - Wire |
| BS EN 3954-2001 | 航空航天系列.银基合金AG-B12401(AgCu40Zn5Ni).硬钎焊用填充金属.粉末或糊料 | Aerospace series - Silver base alloy AG-B12401 (AgCu40Zn5Ni) - Filler metal for brazing - Powder or paste |
| BS EN 3955-2001 | 航空航天系列.银基合金AG-B12401(AgCu40Zn5Ni).硬钎焊用填充金属.轧制的箔材 | Aerospace series - Silver base alloy AG-B12401 (AgCu40Zn5Ni) - Filler metal for brazing - Rolled foil |
| BS EN 3956-2001 | 航空航天系列.银基合金AG-B14001(AgCu42Ni2).硬钎焊用填充金属.金属丝 | Aerospace series - Silver base alloy AG-B14001 (AgCu42Ni2) - Filler metal for brazing - Wire |
| BS EN 3957-2001 | 航空航天系列.银基合金AG-B14001(AgCu42Ni2).硬钎焊用填充金属.粉末或糊料 | Aerospace series - Silver base alloy AG-B14001 (AgCu42Ni2) - Filler metal for brazing - Powder or paste |
| BS EN 3958-2001 | 航空航天系列.银基合金AG-B14001(AgCu42Ni2).硬钎焊用填充金属.轧制的箔材 | Aerospace series - Silver base alloy AG-B14001 (AgCu42Ni2) - Filler metal for brazing - Rolled foil |
| BS EN 3959-2001 | 航空航天系列.钴基合金CO-B41601(CoCr19Ni17Si8W4).硬钎焊填充金属.粉末或糊料 | Aerospace series - Cobalt base alloy CO-B41601 (CoCr19Ni17Si8W4) - Filler metal for brazing - Powder or paste |
| BS EN 3960-2001 | 航空航天系列.金基合金AU-B40001(AuNi18).硬钎焊填充金属.粉末和糊料 | Aerospace series - Gold base alloy AU-B40001 (AuNi18) - Filler metal for brazing - Powder or paste |
| BS EN 3961-2001 | 航空航天系列.金基合金AU-B4000.硬钎焊用填充金属.轧制箔 | Aerospace series - Gold base alloy AU-B4000 - Filler metal for brazing - Rolled foil |
| BS EN 3962-2001 | 航空航天系列.金基合金AU-B40001.硬钎焊用填充金属.金属丝 | Aerospace series - Gold base alloy AU-B40001 - Filler metal for brazing - Wire |
| BS EN 3965-2001 | 航空航天系列.钛合金TI-B17001.硬钎焊用填充金属.轧制的箔材 | Aerospace series - Titanium alloy TI-B17001 - Filler metal for brazing - Rolled foil |
| BS EN 3976-2006 | 航空航天系列.钛和钛合金.试验方法.氢含量测定用化学分析 | Aerospace series - Titanium and titanium alloys - Test method - Chemical analysis for the determination of hydrogen content |
| BS EN 3979-2005 | 航空航天系列.AL-P8090-O2型铝合金.超塑性成型(SPF)用薄板材.0.8mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P8090-O2 - Sheet for superplastic forming (SPF) - 0,8 mm <= a <= 6 mm |
| BS EN 3997-2007 | 航空航天系列.AL-P2024-T3型铝合金.薄板材和带材.0.4mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P2024-T3 - Sheet and strip 0 ,4 mm $3Q a $3Q 6 mm |
| BS EN 3998-2007 | 航空航天系列.AL-P2024-T4或T42型铝合金.薄板材和带材.0.3mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P2024-T4 or T42 - Sheet and strip - 0,3 mm a 6 mm |
| BS EN 3999-2007 | 航空航天系列.AL-P2024-T351型铝合金.改进的化学铣削性能1.6mm≤a≤6mm的薄板材和带材 | Aerospace series - Aluminium alloy AL-P2024-T351 - Sheet and strip with improved chemical milling capability 1,6 mm a 6 mm |
| BS EN 4001-2007 | 航空航天系列.AL-P2024-T351型铝合金.改进的化学铣削性能1.6mm≤a≤6mm的镀铝薄板材和带材 | Aerospace series - Aluminium alloy AL-P2024-T351 - Clad sheet and strip with improved chemical milling capability 1,6 mm a 6 mm |
| BS EN 4002-2007 | 航空航天系列.AL-P2219-T81型铝合金.0.5mm≤a≤6mm的薄板材和带材 | Aerospace series - Aluminium alloy AL-P2219-T81 - Sheet and strip 0,5 mm a 6 mm |
| BS EN 4003-2006 | 航空航天系列.铝合金AL-P2219-T87.薄板材和带材0.5mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P2219-T87 - Sheet and strip 0,5 mm a 6 mm |
| BS EN 4004-2007 | 航空航天系列.AL-P3103-H16型铝合金.薄板材和带材.0.4mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P3103-H16 - Sheet and strip - 0,4 mm a 6 mm |
| BS EN 4005-2007 | 航空航天系列.AL-P5052-O型铝合金.薄板材和带材.0.3mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P5052-O - Sheet and strip 0 ,3 mm a 6 mm |
| BS EN 4006-2007 | 航空航天系列.AL-P6082-T4或T42型铝合金.薄板材和带材.0.4mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P6082-T4 or T42 - Sheet and strip 0,4 mm a 6 mm |
| BS EN 4007-2005 | 铝合金AL-P6082-T6或T62.薄板和带材.0.4 mm≤a≤6 mm | Aerospace series - Aluminium alloy AL-P6082-T6 or T62 - Sheet and strip - 0,4 mm a 6 mm |
| BS EN 4009-2005 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金718)制中长螺纹、紧公差柄、十二角头螺栓.等级:1550MPa(室 | Aerospace series - Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification: 1550 MPa (at ambient temperature) |
| BS EN 4011-2005 | 航空航天系列.十二角头自锁紧的镀银耐热镍基合金NI-PH2601(铬镍铁合金718)螺母.等级:1550MPa(室温)/600 鳦 | Aerospace series - Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), silver plated - Classification: 1550 MPa (at ambient temperature)/600 °C |
| BS EN 4012-2004 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金718)制MoS2涂覆的自锁紧双六角头螺母.等级:1550MPa(室温)/4 | Aerospace series - Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), MoS2 coated - Classification - 1 550 MPa (at ambient temperature) / 425 °C |
| BS EN 4013-2005 | 航空航天系列.自锁紧镀银耐热镍基合金NI-PH2601(铬镍铁合金718)制带柄螺母.等级:1550MPa(室温)/600 鳦 | Aerospace series - Shank nuts, self-locking, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), silver plated - Classification: 1550 MPa (at ambient temperature) / 600 °C |
| BS EN 4017-2001 | 航空航天系列.钛合金管连接件8°30'.90°弯头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 90 ° |
| BS EN 4018-2001 | 航空航天系列.钛合金管连接件8°30'.带止推金属丝螺母的90°弯头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 90 ° with thrust wire nut |
| BS EN 4019-2001 | 航空航天系列.钛合金管连接件8°30'.焊接的90°弯头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 90 °, welded |
| BS EN 4020-2001 | 航空航天系列.钛合金8°30'管连接件.带止推金属丝螺母(thrust wire nut)的90°弯头焊接端 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 90 °, welded end with thrust wire nut |
| BS EN 4021-2001 | 航空航天系列.钛合金管连接件8°30'.闷头90°弯头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 90 °, bulkhead |
| BS EN 4022-2001 | 航空航天系列.钛合金管连接件8°30'.闷头、90°弯头焊接端头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 90 °, bulkhead, welded end |
| BS EN 4023-2001 | 航空航天系列.钛合金管连接件8°30'.45°弯头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 45 ° |
| BS EN 4024-2001 | 航空航天系列.钛合金管连接件8°30'.带止推金属丝螺母的45°弯头焊接端头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 45 ° welded end with thrust wire nut |
| BS EN 4025-2001 | 航空航天系列.钛合金管连接件8°30'.45°弯头闷头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 45 °, bulkhead |
| BS EN 4026-2001 | 航空航天系列.钛合金管连接件8°30'.三通管 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees |
| BS EN 4027-2001 | 航空航天系列.钛合金管连接件8°30'.带止推金属丝螺母的三通管分支 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees branch with thrust wire nut |
| BS EN 4028-2001 | 航空航天系列.钛合金管连接件8°30'.在使用的带止推金属丝螺母的三通管 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees with thrust wire nut on run |
| BS EN 4029-2001 | 航空航天系列.钛合金管连接件8°30'.三通管闷头分支 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees bulkhead branch |
| BS EN 4030-2001 | 航空航天系列.钛合金管连接件8°30'.还在使用的三通管闷头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees bulkhead on run |
| BS EN 4031-2001 | 航空航天系列.钛合金管连接件8°30'.焊接活接头用螺母 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Nut for welded union |
| BS EN 4032-2001 | 航空航天系列.钛合金管连接件8°30'.止推金属丝 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Thrust wire |
| BS EN 4035-2006 | 航空航天系列.减小内部径向间隙和带螺纹钛合金杆耐腐蚀钢可调自动对心双列球轴承的杆端.尺寸和载荷 | Rod ends, adjustable with self-aligning double row ball bearing in corrosion resisting steel, reduced internal radial clearance and threaded shank in titanium alloy - Dimensions and loads |
| BS EN 4045-2001 | 航空航天系列.耐热合金制的无缝毛细管.直径为0.6mm 2mm.尺寸 | Aerospace series - Capillary tubes, seamless in heat resisting alloys - Diameter 0,6 mm D 2 mm - Dimensions |
| BS EN 4047-2004 | 航空航天系列.自锁紧MJ螺纹镀银耐热镍基合金NI-PH2601(铬镍铁合金718)螺母.等级:1550MPa(室温)/600 鳦.技术 | Aerospace series - Nuts, self-locking, MJ threads, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), silver plated - Classification: 1550MPa (at ambient temperature)/600 °C - Technical specification |
| BS EN 4048-2004 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金718)制MoS2涂覆的自锁、带MJ螺纹的螺母.等级:1550MPa(室温) | Aerospace series - Nuts, self-locking, MJ threads, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), MoS2 coated - Classification - 1 550 MPa (at ambient temperature) / 425 °C - Technical specification |
| BS EN 4051-2002 | 航空航天系列.TI-P64001型钛合金制、球形、60度管连接器.油口接头 | Aerospace series - Pipe couplings, 60 °, spherical, in titanium alloy - Port connection |
| BS EN 4054-2004 | 航空航天系列.管连接件、松套法兰和密封件.碳氟化合物橡胶密封件和铝合金保护壳.技术规范 | Aerospace series - Pipe couplings, loose flanges and seals - Seals in fluorocarbon rubber and armature in aluminium alloy - Technical specification |
| BS EN 4058-2001 | 航空航天系列.钛和钛合金制的焊接用填充杆材和填充金属丝.直径为0.5mm 5.0mm.尺寸 | Aerospace series - Filler rods and filler wires for welding in titanium and titanium alloys - Diameter 0,5 mm D 5,0 mm - Dimensions |
| BS EN 4060-2001 | 航空航天系列.钛和钛合金制的焊接用填充杆材和填充金属丝.直径为0.5mm 5.0mm.尺寸 | Aerospace series - Filler rods and filler wires for welding in heat resisting alloys - Diameter 0,5 mm D 5,0 mm - Dimensions |
| BS EN 4085-2001 | 航空航天系列.镍基合金 Ni-40002.硬钎焊填充金属.非晶态箔 | Aerospace series - Nickel base alloy NI-B40002 (NiSi4B2) - Filler metal for brazing - Amorphous foil |
| BS EN 4099-2005 | 铝合金AL-P2219-T6或T62.覆层薄板和带材.0.5 mm≤a≤6 mm | Aerospace series - Aluminium alloy AL-P2219-T6 or T62 - Clad sheet and strip - 0,5 mm a 6 mm |
| BS EN 4100-2005 | 铝合金AL-P2219-T6或T62.薄板和带材.0.5 mm≤a≤6 mm | Aerospace series - Aluminium alloy AL-P2219-T6 or T62 - Sheet and strip - 0,5 mm a 6 mm |
| BS EN 4101-2005 | 铝合金AL-P2024-T4.改进拉伸成形性能的薄板和带材.0.4 mm≤a≤6 mm | Aerospace series - Aluminium alloy AL-P2024-T4 - Sheet and strip with improved stretch forming capability - 0,4 mm a 6 mm |
| BS EN 4102-2005 | 航空航天系列.铝合金AL-P2219-T81.覆层薄板和带材.0.5 mm≤a≤6 mm | Aerospace series - Aluminium alloy AL-P2219-T81 - Clad sheet and strip - 0,5 mm a 6 mm |
| BS EN 4103-2001 | 航空航天系列.镍基合金NI-B40002(NiSi4B2).钎焊用填充金属.硼化物箔 | Aerospace series - Nickel base alloy NI-B40002 (NiSi4B2) - Filler metal for brazing - Borided foil |
| BS EN 4104-2001 | 航空航天系列.NI-B40002镍基合金.硬钎焊用填充金属.粉末或糊料 | Aerospace series - Nickel base alloy NI-B40002 - Filler metal for brazing - Powder or paste |
| BS EN 4105-1998 | 镍基合金NI-B40002(NiSi4B2).铜焊用填充金属.带材 | Nickel base alloy NI-B40002 (NiSi4B2) - Filler metal for brazing - Tape |
| BS EN 4114-2001 | 航空航天系列.带橡胶衬料的铝合金环形卡箍("P"型).尺寸和质量 | Aerospace series - Clamps, loop ("P" type) in aluminium alloy with rubber cushioning - Dimensions and masses |
| BS EN 4117-2004 | 航空航天系列.十二角头自锁紧螺纹镀银的耐热镍基合金NI-PH 2601(铬镍铁合金718)螺母.等级:1550MPa(室温)/60 | Aerospace series - Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), silver plated on thread - Classification - 1 550 MPa (at ambient temperature) / 600 °C |
| BS EN 4120-2004 | 十二角、自锁紧、NI-PH1302耐热镍基合金(沃斯帕洛尹合金)、螺纹镀银的螺母.分类:1210MPa(环境温度下)/730 | Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-PH1302 (Waspaloy), silver plated on thread - Classification - 1 210 MPa (at ambient temperature) / 730 °C |
| BS EN 4123-2004 | 航空航天系列.自锁紧螺纹镀银的耐热镍基合金NI-PH 2601(铬镍铁合金718)带柄螺母.等级:1550MPa(室温)/600 鳦 | Aerospace series - Shank nuts, self-locking, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), silver plated on thread - Classification - 1 550 MPa (at ambient temperature) / 600 °C |
| BS EN 4124-2004 | 航空航天系列.60 型模用自锁紧螺纹镀银的耐热镍基合金NI-PH1302(一种耐高热镍基合金)带柄螺母.等级:1210MP | Aerospace series - Shank nuts, self-locking, heat resisting nickel base alloy NI-PH1302 (Waspaloy), silver plated on thread, for 60 ° swage - Classification - 1 210 MPa (at ambient temperature) / 730 °C |
| BS EN 4172-2006 | 航空航天系列.紧公差TI-P64001阳极电镀的米制钛合金杆沉头、凹头锁紧螺栓.分类:1100 MPa / 315 °C（周围温 | Lockbolts, protruding head, sheartype, close tolerance, in titanium alloy TI-P64001, anodized, metric series - Classification: 1 100 MPa (at ambient temperature) / 315 °C |
| BS EN 4173-2006 | 航空航天系列.紧公差TI-P64001阳极电镀的米制钛合金杆１００°正常头、凹头锁紧螺栓.分类:1100 MPa / 315 | Lockbolts, 100 countersunk normal head, sheartype, close tolerance, in titanium alloy TI-P64001, anodized, metric series - Classification: 1100 MPa (at ambient temperature) / 315 °C |
| BS EN 4174-2006 | 航天航空系列.阳极电镀或铬酸盐处理铝合金2024米制系列、连接模压锁紧凹头紧固件 | Collars, swage locking, sheartype, in aluminium alloy 2024, anodized or chromated, metric series |
| BS EN 4175-2005 | 航天航空系列.TI-P99002型钛合金米制系列、法兰连接模压锁紧切变型垫圈 | Aerospace series - Collars, flanged swage locking, sheartype, in titanium TI-P99002, metric series |
| BS EN 4176-2005 | 航空航天系列.紧公差TI-P64001钛合金制阳极电镀或铝质有色覆层１００°正常或沉头紧固/凹头锁紧螺栓.TI-P99 | Aerospace series - Lockbolts, 100 ° countersunk normal head or protruding head, tension-/ sheartype, close tolerance, in titanium alloy TI-P64001, anodized or with aluminium pigmented coating - Collars in titanium TI-P99002 or aluminium alloy 2024 - Metric series - Technical specification |
| BS EN 4180-2002 | 航空航天系列.流体用钛及钛合金圆形管.宽度公差.直径为4mm D 40mm.尺寸 | Aerospace series - Circular tubes, for fluids in titanium and titanium alloys - Wide tolerances - Diameter 4 mm D 40 mm - Dimensions |
| BS EN 4182-2001 | 航空航天系列.钛合金管连接件8°30'.异径三通管 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees, reduced |
| BS EN 4183-2001 | 航空航天系列.钛合金管连接件8°30'.90°弯头焊接端头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 90 ° welded ends |
| BS EN 4184-2001 | 航空航天系列.钛合金管连接件8°30'.45°弯头双焊接端头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 45 ° double, welded ends |
| BS EN 4185-2001 | 航空航天系列.钛合金管连接件8°30'.长闷头三通管 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees, bulkhead on run long |
| BS EN 4186-2001 | 航空航天系列.钛合金管连接件8°30'.十字形活接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, cross |
| BS EN 4187-2001 | 航空航天系列.钛合金管连接件8°30'.90°弯头长闷头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 90 °, bulkhead, long |
| BS EN 4188-2001 | 航空航天系列.钛合金管连接件8°30'.90°弯头长闷头焊接端头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Elbows 90 ° bulkhead, long, welded end |
| BS EN 4189-2001 | 航空航天系列.钛合金8°30'管连接件.带有长闷头套管的三通管 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees, bulkhead branch long |
| BS EN 4190-2001 | 航空航天系列.钛合金管连接件8°30'.在使用的带止推金属丝的缩径三通管 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees, reduced with thrust wire nut on run |
| BS EN 4191-2001 | 航空航天系列.钛合金管连接件8°30'.缩径三通管长闷头分支 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees, reduced, bulkhead branch, long |
| BS EN 4192-2001 | 航空航天系列.钛合金8°30'管连接件.带有缩短闷头套管的三通管 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees, reduced bulkhead branch |
| BS EN 4193-2001 | 航空航天系列.钛合金8°30'管连接件.带有异径长闷头的三通管 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees, reduced bulkhead on run long |
| BS EN 4194-2001 | 航空航天系列.钛合金8°30'管连接件.带有异径闷头三通管 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Tees, reduced, bulkhead |
| BS EN 4202-2005 | 航空航天系列.铝合金AL-P6082-T651.板材.6 mm≤a≤25 mm | Aerospace series - Aluminium alloy AL-P6082-T651 - Plate - 6 mm a 25 mm |
| BS EN 4203-2005 | 航空航天系列.AL-P8090-T89型铝合金.薄板材.0.6mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P8090-T89 - Sheet - 0,6 mm <= a <= 6 mm |
| BS EN 4204-2005 | 航空航天系列.AL-P8090-T841型铝合金.薄板材.0.6mm≤a≤6mm | Aerospace series - Aluminium alloy AL-P8090 - T841 - Sheet - 0,6 mm <= a <= 6 mm |
| BS EN 4209-2005 | 航空航天系列.AL-P2219-T851型铝合金.厚板材. 6 mm <=50 mm | Aluminium alloy AL-P2219-T851 - Plate - 6 mm ＜a ≤50 mm |
| BS EN 4211-2005 | 航空航天系列.铝合金AL-P2024-T42.覆层板材.6 mm≤a≤25 mm | Aerospace series - Aluminium alloy AL-P2024-T42 - Clad plate - 6 mm a 25 mm |
| BS EN 4212-2005 | 航空航天系列.铝合金AL-P5086-H111.板材.6 mm≤a≤80 mm | Aerospace series - Aluminium alloy AL-P5086-H111 - Plate - 6 mm a 80 mm |
| BS EN 4213-2005 | 航空航天系列.铝合金AL-P6061-T651.板材.6 mm≤a≤80 mm | Aerospace series - Aluminium alloy AL-P6061-T651 - Plate - 6 mm a 80 mm |
| BS EN 4214-2005 | 航空航天系列.铝合金AL-P7010-T651.板材.6 mm≤a≤20 mm | Aerospace series - Aluminium alloy AL-P7010-T651 - Plate - 6 mm a 20 mm |
| BS EN 4215-2005 | 航空航天系列.铝合金AL-P7175-T651.板材.6 mm≤a≤80 mm | Aerospace series - Aluminium alloy AL-P7175-T651 - Plate - 6 mm a 80 mm |
| BS EN 4233-2001 | 航空航天系列.钛合金管连接件8°30'.带螺纹的焊接活接头 | Aerospace series - Pipe coupling 8 °30' in titanium alloy - Unions, welded, threaded |
| BS EN 4247-2005 | 航空航天系列.铝合金AL-P2024-T42.板材.6 mm≤a≤140 mm | Aerospace series - Aluminium alloy AL-P2024-T42 - Plate - 6 mm a 140 mm |
| BS EN 4250-2001 | 航空航天系列.镍基合金NI-B41001(NiCr19Si7B).硬钎焊填充金属.非晶质箔材 | Aerospace series - Nickel base alloys NI-B41001 (NiCr19Si7B) - Filler metal for brazing - Amorphous foil |
| BS EN 4267-2001 | 航空航天系列.钛和钛合金制的圆形棒材.直径为6mm 160mm.尺寸 | Aerospace series - Round bar in titanium and titanium alloys - Diameter 6 mm D 160 mm - Dimensions |
| BS EN 4283-2005 | 航空航天系列.AL-P2219-T87型铝合金.板材.6mm≤a≤40mm | Aerospace series - Aluminium alloy AL-P2219-T87 - Plate - 6 mm < a <= 40 mm |
| BS EN 4286-2005 | 航空航天系列.铝合金AL-P8090-T89.模锻件.a≤125 mm | Aerospace series - Aluminium alloy AL-P8090-T89 - Die forgings - a 125 mm |
| BS EN 4287-2005 | 航天航空系列.AL-P7010型铝合金.锻坯件 | Aerospace series - Aluminium alloy AL-P7010 - Forging stock |
| BS EN 4291-2005 | 航空航天系列.铝合金AL-P8090.锻造坯料 | Aerospace series - Aluminium alloy AL-P8090 - Forging stock |
| BS EN 4292-2005 | 航空航天系列.铝合金AL-R39002.锻造坯料 | Aerospace series - Aluminium alloy AL-R39002 - Forging stock |
| BS EN 4313-2005 | 航空航天系列.铝合金AL-P6013-T6.薄板和带材.0.5 mm≤a≤6 mm | Aerospace series - Aluminium aloy AL-P6013-T6 - Sheet and strip - 0,5 mm a 6 mm |
| BS EN 4321-2004 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金 718)制的带安全锁线孔、细杆、长螺纹、镀银的双六角头螺栓 | Aerospace series - Bolts, double hexagon head with lockwire holes , relieved shank, long thread, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), silver plated - Classification - 1 550 Mpa (at ambient temperature)/650 °C |
| BS EN 4322-2004 | 航空航天系列.钛合金TI-P64001制的带安全锁线孔、细杆、长螺纹、阳极氧化、镀MoS2的双六角头螺栓.强度等级. | Aerospace series - Bolts, double hexagon head with lockwire holes , relieved shank, long thread, in titanium alloy TI-P64001, anodized , MoS2 coated - Strength class - 1 100 MPa (at ambient temperature) |
| BS EN 4323-2004 | 航空航天系列.钛合金TI-P64001制的六瓣凹槽、全杆螺纹、阳极氧化、镀MoS2的100 沉头螺钉.分类.900MPa(室温 | Aerospace series - Screws, 100 ° countersunk head, six lobe recess, threaded to head, in titanium alloy TI-P64001, anodized, MoS2 coated - Classification - 900 MPa (at ambient temperature) / 350 °C |
| BS EN 4324-2002 | 航空航天系列.AL-W42201铝合金.焊接用填充金属.焊条 | Aerospace series - Aluminium alloy AL-W42201 - Filler metal for welding - Rod |
| BS EN 4325-2001 | 航空航天系列.耐热合金NI-WH1302(NiCr20Co13Mo4Ti3Ai).焊接填充金属.金属丝和焊条 | Aerospace series - Heat resisting alloy NI-WH1302 (NiCr20Co13Mo4Ti3AI) - Filler metal for welding - Wire and rod |
| BS EN 4326-2001 | 航空航天系列.耐热合金CO-WH4102(CoCr28W20Ni5V1).硬钎焊用填充金属.金属丝和焊条 | Aerospace series - Heat resisting alloy CO-WH4102 (CoCr28W20Ni5V1) - Filler metal for welding - Wire and rod |
| BS EN 4327-2001 | 航空航天系列.耐热合金CO-WH1401(CoCr26Ni11W8).硬钎焊用填充金属.金属丝和焊条 | Aerospace series - Heat resisting alloy CO-WH1401 (CoCr26Ni11W8) - Filler metal for welding - Wire and rod |
| BS EN 4329-2001 | 航空航天系列.耐热合金NI-WH0001(NiCr20).焊接填充金属.金属丝和焊条 | Aerospace series - Heat resisting alloy NI-WH0001 (NiCr20) - Filler metal for welding - Wire and rod |
| BS EN 4337-2001 | 航空航天系列.耐热合金NI-WH8901(NiCr16Ti3Mn2).硬钎焊用填充金属.金属丝和焊条 | Aerospace series - Heat resisting alloy NI-WH8901 (NiCr16Ti3Mn2) - Filler metal for welding - Wire and rod |
| BS EN 4338-2001 | 航空航天系列.耐热合金NI-WH3902(NiCr25Mo10C).硬钎焊用填充金属.金属丝和焊条 | Aerospace series - Heat resisting alloy - NI-WH3902 (NiCr25Mo10C) - Filler metal for welding - Wire and rod |
| BS EN 4339-2001 | 航空航天系列.耐热合金CO-WH4001(CoCr29W9).硬钎焊用填充金属.金属丝和焊条 | Aerospace series - Heat resisting alloy CO-WH4001 (CoCr29W9) - Filler metal for welding - Wire and rod |
| BS EN 4340-2002 | 航空航天系列.MG-W68001镁合金钢. 焊接用填充金属.焊丝和焊条 | Aerospace series - Magnesium alloy MG-W68001 - Filler metal for welding - Wire and rod |
| BS EN 4341-2001 | 航空航天系列.铝合金AL-W46431.焊接填充金属.金属丝和焊条 | Aerospace series - Aluminium alloy AL-W46431 - Filler metal for welding - Wire and rod |
| BS EN 4352-2004 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金 718)制带安全锁线孔、细杆、长螺纹、镀MoS2 的双六角头螺 | Aerospace series - Bolts, double hexagon head with lockwire holes , relieved shank, long thread, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), MoS2 coated - Classification - 1 550 MPa (at ambient temperature) / 425 °C |
| BS EN 4382-2006 | 航空航天系列.NI-PH3601(NiCr22Mo9Nb)型耐热合金.溶解处理的.无缝管.液压用.D≤50mm、a≤3mm | Aerospace series - Heat resisting alloy NI-PH3601 (NiCr22Mo9Nb) - Solution treated - Seamless tubes - For hydraulic application - D ≤ 50 mm, a ≤ 3 mm |
| BS EN 4383-2006 | 航空航天系列.NI-CH2601(NiCr19Fe19Nb5Mo3)型耐热合金.非热处理的.重熔坯料 | Aerospace series - Heat resisting alloy NI-CH2601 (NiCr19Fe19Nb5Mo3) - Non heat treated - Remelting stock |
| BS EN 440-1995 | 焊接消耗材料.非合金与细晶粒钢的气体保护金属电弧焊用丝状电极和熔积物.分类 | Welding consumables - Wire electrodes and deposits for gas shielded metal arc welding of non alloy and fine grain steels - Classification |
| BS EN 4401-2006 | 航空航天系列.紧公差TI-P64001铝制有色覆层的米制钛合金杆沉头、凹头锁紧螺栓.分类:1100 MPa / 315 °C（周 | Lockbolts, protruding head, sheartype, close tolerance, in titanium alloy TI-P64001, with aluminium pigmented coating, metric series - Classification: 1100 MPa (at ambient temperature) / 315 °C |
| BS EN 4402-2006 | 航空航天系列.紧公差TI-P64001铝制有色覆层的米制钛合金杆１００°正常头、凹头锁紧螺栓.分类:1100 MPa / 3 | Lockbolts, 100 °countersunk normal head, sheartype, close tolerance, in titanium alloy TI-P64001,with aluminium pigmented coating, metric series - Classification: 1100 MPa (at ambient temperature) / 315 °C |
| BS EN 4420-2003 | 航空航天系列.FE-PA3903型合金钢制弹簧夹 | Aerospace series - Clips, spring tension, in alloy steel FE-PA3903 |
| BS EN 4421-2007 | 航空航天系列.带锯齿状、耐腐蚀钢锁紧环的、镀MoS2涂层的、TI-P64001钛合金螺柱.强度等级:1100MPa(环境温度 | Aerospace series - Studs, in titanium alloy TI-P64001, MoS2 coated, with serrated locking ring in corrosion resisting steel - Strength class: 1 100 MPa (at ambient temperature) |
| BS EN 4434-2005 | 航空航天系列.电缆的铜和铜合金轻型导体.产品质量（正常和紧公差） | Copper or copper alloy lightweight conductors for electrical cables — Product standard (Normal and tight tolerances) |
| BS EN 4449-2005 | AL-P7050-T76型铝合金.薄板材.0.8mm≤a≤6mm | Aluminium alloy AL-P7050 - T76 - Sheet - 0,8 mm ≤ a ≤ 6 mm |
| BS EN 4450-2005 | 航空航天系列.铝合金AL-P7050-T762.薄板.0.8 mm≤a≤6 mm | Aerospace series - Aluminium alloy AL-P7050-T762 - Sheet - 0,8 mm a 6 mm |
| BS EN 4458-2005 | 航空航天系列.带锯齿状锁紧环耐腐蚀钢镀MoS2涂层的TI-P64001型钛合金MJ螺纹螺柱.强度等级:1100MPa(室温).技 | Aerospace series - Studs, MJ threads, in titanium alloy TI-P64001 , MoS2 coated, with serrated locking ring in corrosion resisting steel.Strengt h class: 1100 MPa (at ambient temperature) - Technicalspecification |
| BS EN 4459-2005 | 航空航天系列.钛合金TI-P64001制带锯齿型锁环的耐腐钢螺柱.设计标准 | Aerospace series - Studs, in titanium alloy TI-P64001, with serrated locking ring in corrosion resisting steel - Design standard |
| BS EN 4460-2005 | 航空航天系列.钛合金TI-P64001制带锯齿型锁环的耐腐钢螺柱.安装和拆卸程序 | Aerospace series - Studs, in titanium alloy TI-P64001, with serrated locking ring in corrosion resisting steel - Installation and removal procedure |
| BS EN 4496-2005 | 航空航天系列.有色铝涂层、阳极化的、钛合金、短螺纹、紧公差标称杆、偏位十字凹槽沉头标称100 °螺钉.等级 | Aerospace series - Screws, 100 ° countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating - Classification: 1 100 MPa (at ambient temperature) / 315 °C |
| BS EN 4497-2005 | 航空航天系列.有色铝涂层、阳极化的、钛合金、短螺纹、紧公差标称杆、偏位十字凹槽盘头螺钉.等级:1100MPa( | Aerospace series - Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating - Classification: 1 100 MPa (at ambient temperature) / 315 °C |
| BS EN 4498-2005 | 航空航天系列.有色铝涂层、钝化的、耐热镍基合金、中等长度螺纹、紧公差标称杆、大双六角头螺栓.等级:1550M | Aerospace series - Bolts, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated, with aluminium pigmented coating - Classification: 1 550 MPa (at ambient temperature) / 315 °C |
| BS EN 4501-2006 | 航空航天系列.带镀铝涂层的阳极电镀钛合金短螺纹紧公差标准柄正六角头螺栓、米制系列.等级:1100MPa(室温)/3 | Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating, metric series - Classification: 1100 MPa (at ambient temperature) / 315 °C |
| BS EN 4509-2006 | 航空航天系列.带镀铝涂层阳极氧化的钛合金螺纹延伸到螺头100°沉头偏置十字凹槽螺钉、米制系列.等级:1100MP | Screws, 100 ° countersunk normal head, offset cruciform recess, threaded to head, in titanium alloy, anodized, with aluminium pigmented coating, metric series - Classification: 1 100 MPa (at ambient temperature)/315 °C |
| BS EN 4549-2003 | 航空航天系列.耐热钢或耐热镍合金管连接件.焊接连接端.设计造型.英制 | Aerospace series - Pipe coupling, in heat resisting steel or in heat resisting nickel alloy - Coupling end, welded - Design configuration - Inch series |
| BS EN 4591-2005 | 航空航天.耐高温镍基合金钢制MOS2润滑的自调准筒形游动自锁螺母.等级为:1550 MPa (环境温度) / 315 °C | Aerospace series - Nuts, barrel, self-locking, floating, self-aligning,in heat resisting nickel base alloy, MoS2 lubricated - Classification: 15 50 MPa (at ambient temperature) / 315 °C |
| BS EN 4610-2005 | 航空航天系列.8°30'钛合金管接头.带推进线螺母的45°弯头 | Pipe coupling 8°30' in titanium alloy — Elbows 45°, with thrust wire nut |
| BS EN 4615-2005 | 航空航天系统.MG-C18002镁合金.T4.砂型铸造 | Aerospace series - Magnesium alloy MG-C18002 - T4 - Sand casting |
| BS EN 4616-2005 | 航天航空系列.镁合金MG-C18002.T4.冷型铸造 | Magnesium alloy MG-C18002 - T4 - Chill casting |
| BS EN 485-1-1994 | 铝和铝合金.薄板材、带材和板材.检验和交货技术状态 | Aluminium and aluminium alloys - Sheet, strip and plate - Technical conditions for inspection and delivery |
| BS EN 485-2-2007 | 铝和铝合金.薄板材、带材和板材.机械特性 | Aluminium and aluminium alloys - Sheet, strip and plate - Mechanical properties |
| BS EN 485-3-2003 | 铝和铝合金.片材、带材和板材.热轧制品的形状和尺寸公差 | Aluminium and aluminium alloys - Sheet, strip and plate - Tolerances on dimensions and form for hot-rolled products |
| BS EN 485-4-1994 | 铝和铝合金.薄板材、带材和板材.冷轧制品的形状和尺寸公差 | Aluminium and aluminium alloys - Sheet, strip and plate - Tolerances on shape and dimensions for cold-rolled products |
| BS EN 486-1994 | 铝和铝合金.挤压铸锭.规范 | Aluminium and aluminium alloys - Extrusion ingots - Specifications |
| BS EN 487-1994 | 铝和铝合金.滚轧锭.规范 | Aluminium and aluminium alloys - Rolling ingots - Specifications |
| BS EN 50069-1991 | 充气高压开关设备和控制设备用铸铝合金和锻铝合金焊接混合材料外壳规范 | Specification for welded composite enclosures of cast and wrought aluminium alloys for gas-filled high-voltage switchgear and controlgear |
| BS EN 50149-2001 | 铁路设施.固定置装.电力牵引.铜和铜合金波纹连接线 | Railway applications - Fixed installations - Electric traction - Copper and copper alloy grooved contact wires |
| BS EN 50183-2000 | 架空导线.铝镁硅合金导线 | Conductors for overhead lines - Aluminium-magnesium-silicon alloy wires |
| BS EN 50307-2003 | 铅和铅合金.电缆的铅和铅合金护套和套管 | Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables |
| BS EN 50337-8-3-2007 | 纤维光学通信系统使用的连接器组和互连元件.产品规范.端接在IEC 60793-2-50类B1.1和B1.3单模纤维上的LSH-PC | Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - LSH-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre , composite ferrule category C |
| BS EN 50377-8-2-2007 | 光纤通信系统中使用的连接器组和互连元件.产品规范.端接在IEC 60793-2-50类B1.1和B1.3单模纤维上的LSH-APC | Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Type LSH-APC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre, composite ferrule category C |
| BS EN 50377-8-4-2007 | 光纤通信系统中使用的连接器组和互连元件.产品规范.端接在IEC 60793-2-50类B1.1和B1.3单模纤维上的LSH-APC | Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - LSH-APC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre , composite ferrule category U |
| BS EN 50377-8-5-2007 | 光纤通信系统中使用的连接器组和互连元件.产品规范.端接在IEC 60793-2-50类B1.1和B1.3单模纤维上的LSH-PC单 | Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - LSH-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre , composite ferrule category U |
| BS EN 515-1993 | 铝和铝合金.锻制品.回火标志 | Aluminium and aluminium alloys - Wrought products - Temper designations |
| BS EN 541-2006 | 铝和铝合金.金属罐、密封物和盖子用轧制品.规范 | Aluminium and aluminium alloys — Rolled products for cans, closures and lids — Specifications |
| BS EN 546-1-2006 | 铝和铝合金.箔.第1部分:检验和交付用技术条件 | Aluminium and aluminium alloys - Foil - Part 1: Technical conditions for inspection and delivery |
| BS EN 546-2-2006 | 铝和铝合金.第2部分:箔.机械性能 | Aluminium and aluminium alloys - Part 2: Foil - Mechanical properties |
| BS EN 546-3-2006 | 铝和铝合金.箔.第3部分:尺寸公差 | Aluminium and aluminium alloys - Foil - Part 3: Tolerances on dimensions |
| BS EN 546-4-2006 | 铝和铝合金.箔.第4部分:特殊性能要求 | Aluminium and aluminium alloys - Foil - Part 4: Special property requirements |
| BS EN 570-1995 | 锻铝和铝合金.由可锻制铝产品加工的冲击挤压铝块.规范 | Aluminium and aluminium alloys - Impact extrusion slugs obtained from wrought products - Specifications |
| BS EN 573-1-2004 | 铝和铝合金.锻制产品化学组成和外形.数字标示系统 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Numerical designation system |
| BS EN 573-2-1995 | 铝和铝合金.锻制产品的化学成分和外形.基于化学标志的命名系统 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Chemical symbol based designation system |
| BS EN 573-3-2007 | 铝和铝合金.锻制品的化学成分和形状.产品的化学成分和形状 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Chemical composition and form of products |
| BS EN 573-5-2007 | 铝和铝合金.锻制品的化学成分和形状.标准锻制品汇编 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Codification of standardized wrought products |
| BS EN 575-1996 | 铝和铝合金.熔铸母合金.规范 | Aluminium and aluminium alloys - Master alloys produced by melting - Specifications |
| BS EN 576-2003 | 铝和铝合金.再熔非合金铝锭.规范 | Aluminium and aluminium alloys - Unalloyed aluminium ingots for remelting - Specifications |
| BS EN 577-1996 | 铝和铝合金.液体金属.规范 | Aluminium and aluminium alloys - Liquid metal - Specifications |
| BS EN 586-1-1998 | 铝和铝合金.锻件.检验和交付技术状态 | Aluminium and aluminium alloys - Forgings - Technical conditions for inspection and delivery |
| BS EN 586-2-1994 | 铝和铝合金.锻件.机械特性和附加特性要求 | Aluminium and aluminium alloys - Forgings - Mechanical properties and additional property requirements |
| BS EN 586-3-2002 | 铝和铝合金.锻件.尺寸和形状公差 | Aluminium and aluminium alloys - Forgings - Tolerances on dimensions and form |
| BS EN 601-2004 | 铝和铝合金.铸件.与食品接触用铸件的化学成分 | Aluminum and aluminium alloys - Castings - Chemical composition of castings for use in contact with foodstuff |
| BS EN 602-2004 | 铝和铝合金.锻件.与食品接触的产品制造用半成品的化学成分 | Aluminium and aluminium alloys - Wrought products - Chemical composition of semi-finished products used for the fabrication of articles for use in contact with foodstuff |
| BS EN 603-1-1997 | 铝及铝合金.锻坯.检验和交付技术状态 | Aluminium and aluminium alloys - Wrought forging stock - Technical conditions for inspection and delivery |
| BS EN 603-2-1997 | 铝及铝合金.锻坯.机械性能 | Aluminium and aluminium alloys - Wrought forging stock - Mechanical properties |
| BS EN 603-3-2000 | 铝及铝合金.锻坯.尺寸和形状公差 | Aluminium and aluminium alloys - Wrought forging stock - Tolerances on dimensions and form |
| BS EN 604-1-1997 | 铝及铝合金.铸锻件坯.检查和交付技术状态 | Aluminium and aluminium alloys - Cast forging stock - Technical conditions for inspection and delivery |
| BS EN 604-2-1997 | 铝及铝合金.铸锻件坯.尺寸和形位公差 | Aluminium and aluminium alloys - Cast forging stock - Tolerances on dimensions and form |
| BS EN 610-1996 | 锡和锡合金.锡锭 | Tin and tin alloys - Ingot tin |
| BS EN 611-1-1996 | 锡和锡合金.锡铅合金和锡铅合金器皿.锡铅合金 | Tin and tin alloys - Pewter and pewterware - Pewter |
| BS EN 611-2-1997 | 锡和锡合金.锡铅合金和锡铅合金器皿.第2部分:锡铅合金器皿 | Tin and tin alloys - Pewter and pewterware - Pewterware |
| BS EN 61190-1-3-2007 | 电子组装件用连接材料.电子钎焊用电子级钎焊合金和有助熔剂和无助熔剂的固体焊锡的要求 | Attachment materials for electronic assembly - Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solders for electronic soldering applications |
| BS EN 61755-3-5-2006 | 纤维光学连接器的光学接口.第3-5部分:光学接口.使用铜-镍合金作为单模纤维光纤接口材料用的直径2.5mm和1.25 | Fibre optic connector optical interfaces - Part 3-5: Optical interface - 2,5 mm and 1,25 mm diameter cylindrical PC composite ferrule using Cu-Ni-alloy as fibre surrounding material, single modefibre |
| BS EN 61755-3-6-2006 | 纤维光学连接器的光学接口.第3-6部分:光接口.用铜-镍合金作为纤维环绕材料的单模光纤直径2.5mm和1.25mm圆柱 | Fibre optic connector optical interfaces - Part 3-6: Optical interface - 2,5 mm and 1,25 mm diameter cylindrical 8 degreesangled-PC composite ferrule using Cu-Ni-alloy as fibre surroundingmaterial, single mode fibre |
| BS EN 61788-3-2006 | 超导性.临界电流测量.涂层银或银合金的Bi-2212和Bi-2223氧化超导体的直流临界电流 | Superconductivity - Part 3: Critical current measurement - DC critical current of Ag- and/or Ag alloy-sheathed Bi-2212 and Bi-2223 oxide superconductors |
| BS EN 683-1-2006 | 铝和铝合金.叶片坯料.第1部分:检验和交付技术条件 | Aluminium and aluminium alloys. Finstock. Part 1: Technical conditions for inspection and delivery |
| BS EN 683-2-2006 | 铝和铝合金.散热片坯料.第2部分:机械特性 | Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties |
| BS EN 683-3-2006 | 铝和铝合金.散热片坯料.第3部分:尺寸和形状公差 | Aluminium and aluminium alloys - Finstock - Part 3: Tolerances on dimensions and form |
| BS EN 723-1996 | 铜和铜合金.铜管道和接头的内表面积碳测定的燃烧方法 | Copper and copper alloys - Combustion method for determination of carbon on the inner surface of copper tubes or fittings |
| BS EN 754-1-1997 | 铝和铝合金.冷拉短棒材/棒材和管材.第1部分:检验和交付技术状态 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Technical conditions for inspection and delivery |
| BS EN 754-2-1997 | 铝和铝合金.冷拉短棒材/棒材和管材.第2部分:机械特性 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Mechanical properties |
| BS EN 754-3-1996 | 铝和铝合金.冷拉短棒材/棒材和管材.圆棒材的尺寸和形位公差 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Round bars, tolerances on dimensions and form |
| BS EN 754-4-1996 | 铝和铝合金.锻制品.冷拉短棒材/棒材和管材.方棒材的形位公差 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Square bars, tolerances on dimensions and form |
| BS EN 754-5-1996 | 锻铝和铝合金.冷拉短棒材/棒材和管材.第5部分:矩形棒材.尺寸和形位公差 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Rectangular bars, tolerances on dimensions and form |
| BS EN 754-6-1996 | 铝和铝合金.冷拉短棒材/棒材和管材.冷拉六角形棒材的尺寸和形位公差 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Hexagonal bars, tolerances on dimensions and form |
| BS EN 754-7-1998 | 铝和铝合金.冷拉棒材和管材.无缝管.尺寸和形状公差 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Seamless tubes, tolerances on dimensions and form |
| BS EN 754-8-1998 | 铝和铝合金.冷拉短棒材/棒材和管材.出水孔管.尺寸和形状公差 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Porthole tubes, tolerances on dimensions and form |
| BS EN 755-1-1997 | 铝和铝合金.挤压短棒材/棒材、管材和型材.检验和交付技术状态 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Technical conditions for inspection and delivery |
| BS EN 755-2-1997 | 铝和铝合金.挤出杆材/棒材、管材和型材.机械性能 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Mechanical properties |
| BS EN 755-3-1996 | 铝和铝合金.挤压短棒材/棒材、管材和型材.圆棒材的尺寸和形位公差 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Round bars, tolerances on dimensions and form |
| BS EN 755-4-1996 | 铝和铝合金.挤压短棒材/棒材、管材和型材.方棒材的尺寸和形位公差 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Square bars, tolerances on dimensions and form |
| BS EN 755-5-1996 | 铝和铝合金.挤压短棒材/棒材、管材和型材.矩形棒材的尺寸和形位公差 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Rectangular bars, tolerances on dimensions and form |
| BS EN 755-6-1996 | 铝和铝合金.挤压杆材/棒材、管材和型材.六角形棒材的尺寸和形位公差 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Hexagonal bars, tolerances on dimensions and form |
| BS EN 755-7-1998 | 铝和铝合金.挤压短棒材/棒材、管材和型材.无缝管.尺寸和形状公差 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Seamless tubes, tolerances on dimensions and form |
| BS EN 755-8-1998 | 铝和铝合金.挤压短棒材/棒材、管材和型材.出水孔管.尺寸和形状公差 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Porthole tubes, tolerances on dimensions and form |
| BS EN 755-9-2001 | 铝和铝合金.挤压短棒材/棒材、管材及型材.型材的尺寸和形状公差 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Profiles, tolerances on dimensions and form |
| BS EN 756-2004 | 焊接消耗品.非合金和细粒钢埋弧焊用实芯焊丝、实芯焊丝和药芯焊丝混合助熔剂.分类 | Welding consumables - Solid wires, solid wire-flux and tubular cored electrode-flux combinations for submerged arc welding of non alloy and fine grain steels - Classification |
| BS EN 758-1997 | 焊接用料.带有和不带非合金钢及细粒钢气体保护的金属电弧焊接用管状芯焊条.分类 | Welding consumables - Tubular cored electrodes for metal arc welding with and without a gas shield of non-alloy and fine grain steels - Classification |
| BS EN 851-1996 | 铝和铝合金.锻制品.烹调器具用圆形材料和圆坯料规范 | Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications |
| BS EN 941-1996 | 铝和铝合金.圆形材料和圆坯料的通用要求.规范 | Aluminium and aluminium alloys - Circle and circle stock for general applications - Specifications |
| BS EN 988-1997 | 锌和锌合金.建筑用轧制平板材规范 | Zinc and zinc alloys - Specification for rolled flat products for building |
| BS EN IS0 22825-2006 | 焊接的无损试验.超声波试验.奥氏体钢和镍合金焊接试验 | Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels and nickel-based alloys |
| BS EN ISO 10042-2006 | 焊接.铝和铝合金弧焊接头.缺陷质量分级 | Welding - Arc-welded joints in aluminium and its alloys - Quality levels for imperfections |
| BS EN ISO 10993-15-2001 | 医疗器械的生物评定.金属及合金中降解产物的识别与量化 | Biological evaluation of medical devices - Identification and quantification of degradation products from metals and alloys |
| BS EN ISO 11130-1999 | 金属和合金的腐蚀.盐溶液中的交替浸入试验 | Corrosion of metals and alloys - Alternate immersion test in salt solution |
| BS EN ISO 11143-2000 | 牙科设备.汞齐合金分离器 | Dental equipment - Amalgam separators |
| BS EN ISO 11210-1995 | 铂珠宝合金中铂的测定.二铵六氯铂沉淀后的重量法 | Determination of platinum in platinum jewellery alloys - Gravimetric method after precipitation of diammonium hexachloroplatinate |
| BS EN ISO 11306-1998 | 金属和合金腐蚀.金属和合金暴露于海水表面后的评估指南 | Corrosion of metals and alloys - Guidelines for exposing and evaluating metals and alloys in surface sea water |
| BS EN ISO 11426-1999 | 金合金首饰中金含量的测定.灰吹法(火试验法) | Determination of gold in gold jewellery alloys - Cupellation method (fire assay) |
| BS EN ISO 11489-1995 | 铂珠宝合金中铂的测定.氯化汞(I)还原后重量法 | Determination of platinum in platinum jewellery alloys - Gravimetric method after reduction with mercury(I) chloride |
| BS EN ISO 11490-1995 | 钯珠宝合金中钯的测定.丁二酮肟重量法 | Determination of palladium in palladium jewellery alloys - Gravimetric method with dimethyl glyoxime |
| BS EN ISO 12215-3-2002 | 小艇.船体构造和船材尺寸.材料.钢、铝合金、木材及其它材料 | Small craft - Hull construction and scantlings - Materials - Steel, aluminium alloys, wood, other materials |
| BS EN ISO 13680-2002 | 石油和天然气工业.用作套管、油管和接箍的防腐合金无缝钢管.交货技术条件 | Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions |
| BS EN ISO 13897-2004 | 牙科学.汞齐合金胶囊 | Dentistry - Amalgam capsules |
| BS EN ISO 13919-2-2001 | 焊接.电子和激光束焊接接头.缺陷的质量分级指南.铝及其可焊合金 | Welding - Electron and laser beam welded joints - Guidance on quality levels for imperfections - Aluminium and its weldable alloys |
| BS EN ISO 14172-2003 | 焊接消耗品.镍及镍合金金的手工电弧焊接用涂敷焊条.分类 | Welding consumables - Covered electrodes for manual metal arc welding of nickel and nickel alloys - Classification |
| BS EN ISO 14920-1999 | 热喷涂.自熔合金的熔化和喷涂 | Thermal spraying - Spraying and fusing of self-fluxing alloys |
| BS EN ISO 15156-2-2003 | 石油、石化和天然气工业.油、气生产中含硫化氢(H2S)环境下使用的材料.耐裂化碳和低合金钢及铸铁的使用 | Petroleum, petrochemical and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Cracking resistant carbon and low alloy steels, and the use of cast irons |
| BS EN ISO 15156-3-2003 | 石油、石化和天然气工业.油、气生产中含硫化氢(H2S)环境下使用的材料.耐裂化CRAs(耐腐蚀合金)和其他合金 | Petroleum, petrochemical and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys |
| BS EN ISO 15349-2-2003 | 非合金钢.低碳含量的测定.(预热)感应炉燃烧后红外线吸收法 | Unalloyed steel - Determination of low carbon content - Infrared absorption method after combustion in an induction furnace (with preheating) |
| BS EN ISO 15546-2007 | 石油和天然气工业.铝合金钻杆 | Petroleum and natural gas industries - Aluminium alloy drill pipe |
| BS EN ISO 15614-1-2004 | 金属材料焊接程序的规范和鉴定.焊接程序试验.钢的弧焊和气焊以及镍和镍合金的弧焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| BS EN ISO 15614-2-2005 | 金属材料焊接过程的规范和鉴定.焊接过程试验.铝及其合金的电弧焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Arc welding of aluminium and its alloys |
| BS EN ISO 15614-5-2004 | 金属材料焊接程序的规范和鉴定.焊接程序试验.钛、锆及其合金电弧焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Arc welding of titanium, zirconium and their alloys |
| BS EN ISO 15614-6-2006 | 金属材料焊接程序的规范和合格鉴定.焊接程序试验.铜及其合金的弧焊和气焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Arc and gas welding of copper and its alloys |
| BS EN ISO 18273-2004 | 焊接消耗品.铝和铝合金焊接用丝状电极、焊丝和焊条.分类 | Welding consumables - Wire electrodes, wires and rods for welding of aluminium and aluminium alloys - Classification |
| BS EN ISO 18274-2004 | 焊接消耗品.镍和镍合金熔焊用丝状和杆状电极、焊丝和焊条.分类 | Welding consumables - Wire and strip electrodes, wires and rods for fusion welding of nickel and nickel alloys - Classification |
| BS EN ISO 18595-2007 | 电阻焊接.铝和铝合金的点焊.可焊性、焊接和测试 | Resistance welding - Spot welding of aluminium and aluminium alloys - Weldability, welding and testing |
| BS EN ISO 196-1995 | 锻造铜和铜合金.残余应力的测定.硝酸汞(I)试验 | Wrought copper and copper alloys - Detection of residual stress - Mercury(I) nitrate test |
| BS EN ISO 2063-2005 | 热喷镀.金属和其他无机覆层.锌、铝及其合金 | Thermal spraying - Metallic and other inorganic coatings - Zinc, aluminium and their alloys |
| BS EN ISO 24034-2006 | 焊接消耗品.钛和钛合金熔焊用实线和棒材.分类 | Welding consumables - Solid wires and rods for fusion welding of titanium and titanium alloys - Classification |
| BS EN ISO 24234-2004 | 牙科学.牙科汞齐合金用汞及合金 | Dentistry - Mercury and alloys for dental amalgam |
| BS EN ISO 2560-2006 | 焊料.非合金钢和细粒钢的手工金属电弧焊接的涂敷焊条.分类 | Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification |
| BS EN ISO 2566-1-1999 | 钢.伸长值的换算.碳素钢和低合金钢 | Steel - Conversion of elongation values - Carbon and low alloy steels |
| BS EN ISO 2624-1995 | 铜及铜合金.平均粒度估计 | Copper and copper alloys - Estimation of average grain size |
| BS EN ISO 3325-1999 | 不包括硬质合金的烧结金属材料.横向断裂强度的测定 | Sintered metal materials, excluding hardmetals - Determination of transverse rupture strength |
| BS EN ISO 3613-2001 | 锌,镉,铝-锌合金和锌铝合金的铬酸盐转化镀层.试验方法 | Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys - Test methods |
| BS EN ISO 3738-2-2006 | 硬质合金.洛氏硬度试验(等级A).标准试验块的准备和校验 | Hardmetals - Rockwell hardness test (scale A) - Preparation and calibration of standard test blocks |
| BS EN ISO 3815-1-2005 | 锌和锌合金.用光辐射光谱测定法分析固体样品 | Zinc and zinc alloys - Analysis of solid samples by optical emission spectrometry |
| BS EN ISO 3815-2-2005 | 锌和锌合金.用感应耦合等离子体光发射光谱测定法分析 | Zinc and zinc alloys - Analysis by inductively coupled plasma optical emission spectrometry |
| BS EN ISO 3823-1-1999 | 牙科用旋转器械.牙钻.钢制牙钻和硬质合金牙钻 | Dental rotary instruments - Burs - Steel and carbide burs |
| BS EN ISO 3927-2002 | 金属粉末(不包括硬质合金粉末).单轴向压缩时压缩性的测定 | Metallic powders, excluding powders for hardmetals - Determination of compressibility in uniaxial compression |
| BS EN ISO 4524-3-1986 | 金属镀层.电镀金和金合金镀层测试方法.孔隙度电图试验 | Metallic coatings - Test methods for electrodeposited gold and gold alloy coatings - Electrographic tests for porosity |
| BS EN ISO 4524-6-1989 | 金属镀层.电镀金和金合金镀层测试方法.第6部分:残留盐类测定 | Metallic coatings - Test methods for electrodeposited gold and gold alloy coatings - Determination of the presence of residual salts |
| BS EN ISO 4527-2003 | 金属覆层.自催化(无电)镍磷合金覆层.规范和试验方法 | Metallic coatings - Autocatalytic (electroless) nickel-phosphorus alloy coatings - Specification and test methods |
| BS EN ISO 5817-2007 | 焊接.钢、镍、钛和其合金的熔焊接头(束焊除外).缺陷的质量等级 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections |
| BS EN ISO 6509-1995 | 金属和合金耐腐蚀性.黄铜耐脱锌性测定 | Corrosion of metals and alloys - Determination of dezincification resistance of brass |
| BS EN ISO 683-17-1999 | 热处理钢、合金钢和易切削钢.滚珠轴承和滚柱轴承钢 | Heat-treated steels, alloy steels and free-cutting steels - Ball and roller bearing steels |
| BS EN ISO 6978-2-2003 | 天然气.汞的测定.用碘/铂合金混和法采样汞 | Natural gas - Determination of mercury - Sampling of mercury by amalgamation on gold/platinum alloy |
| BS EN ISO 7441-1995 | 金属和合金的耐腐蚀性.在露天暴露腐蚀试验中双金属腐蚀性的测定 | Corrosion of metals and alloys - Determination of bimetallic corrosion in outdoor exposure corrosion tests |
| BS EN ISO 7539-1-1988 | 金属和合金的腐蚀.应力腐蚀试验.第1部分:试验程序的通用指南 | Corrosion of metals and alloys - Stress corrosion testing - General guidance on testing procedures |
| BS EN ISO 7539-2-1990 | 金属和合金的腐蚀.应力腐蚀试验.第2部分:弯曲梁试样的制备和使用 | Corrosion of metals and alloys - Stress corrosion testing - Preparation and use of bent-beam specimens |
| BS EN ISO 7539-3-1990 | 金属和合金的耐腐蚀性.应力腐蚀试验.第3部分:U型弯曲试样的制备和使用 | Corrosion of metals and alloys - Stress corrosion testing - Preparation and use of U-bend specimens |
| BS EN ISO 7539-4-1990 | 金属和合金的腐蚀.应力腐蚀试验.第4部分:轴向载荷拉伸试样的制备和使用 | Corrosion of metals and alloys - Stress corrosion testing - Preparation and use of uniaxially loaded tension specimens |
| BS EN ISO 7539-5-1990 | 金属和合金的腐蚀.应力腐蚀试验.第5部分:C-环形试样的制备和使用 | Corrosion of metals and alloys - Stress corrosion testing - Method for the preparation and use of C-ring specimens |
| BS EN ISO 7539-6-2003 | 金属和合金的腐蚀.应力腐蚀试验.恒定负荷或恒定位移条件下试验用预破裂试样的制备和使用 | Corrosion of metals and alloys - Stress corrosion testing - Preparation and use of pre-cracked specimens for tests under constant load or constant displacement |
| BS EN ISO 7539-7-2005 | 金属与合金的腐蚀.应力腐蚀试验.慢速率应力试验方法 | Corrosion of metals and alloys - Stress corrosion testing - Method for slow strain rate testing |
| BS EN ISO 7787-2-2001 | 牙科旋转器械.切刀.实验室用硬质合金刀 | Dental rotary instruments - Cutters - Carbide laboratory cutters |
| BS EN ISO 7787-4-2002 | 牙科用旋转器械.切割刀具.实验室用小型硬质合金刀具 | Dental rotary instruments - Cutters - Miniature carbide laboratory cutters |
| BS EN ISO 8044-2000 | 金属和合金的腐蚀性.基本术语和定义 | Corrosion of metals and alloys - Basic terms and definitions |
| BS EN ISO 8282-1997 | 牙科设备.汞和合金混合器与分配器 | Dental equipment - Mercury and alloy mixers and dispensers |
| BS EN ISO 8442-7-2001 | 与食品接触的材料和制品.刀具和餐桌凹形餐具.银、其他贵金属及其合金制成的刀具的要求 | Materials and articles in contact with foodstuffs - Cutlery and table holloware - Requirements for table cutlery made of silver, other precious metals and their alloys |
| BS EN ISO 8565-1995 | 金属及合金.大气腐蚀试验.现场试验的总要求 | Metals and alloys - Atmospheric corrosion testing - General requirements for field tests |
| BS EN ISO 898-1-1999 | 碳钢和合金钢制的紧固件的机械特性.螺栓、螺钉和螺柱 | Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws and studs |
| BS EN ISO 898-5-1999 | 碳钢及合金钢制紧固件的机械性能.无拉伸应力下的定位螺钉和类似的螺纹紧固件 | Mechanical properties of fasteners made of carbon steel and alloy steel - Set screws and similar threaded fasteners not under tensile stresses |
| BS EN ISO 9400-1996 | 镍基合金.抗晶间腐蚀性的测定 | Nickel-based alloys - Determination of resistance to intergranular corrosion |
| BS EN ISO 9453-2006 | 软钎料合金.化学成分和形式 | Soft solder alloys - Chemical compositions and forms |
| BS EN ISO 9606-2-2004 | 焊工的认可试验.熔焊.铝和铝合金 | Qualification test of welders - Fusion welding - Aluminium and aluminium alloys |
| BS EN ISO 9606-3-1999 | 焊工的认可测试.熔焊.铜及铜合金 | Approval testing of welders - Fusion welding - Copper and copper alloys |
| BS EN ISO 9606-4-1999 | 焊工的认可测试.熔焊.镍及镍合金 | Approval testing of welders - Fusion welding - Nickel and nickel alloys |
| BS EN ISO 9606-5-2000 | 焊工的认可测试.熔焊.钛和钛合金.锆和锆合金 | Approval testing of welders - Fusion welding - Titanium and titanium alloys, zirconium and zirconium alloys |
| BS EN ISO 9692-3-2001 | 焊接和相关工艺.接头的准备.铝及其合金的金属极惰性气体保护焊和钨极惰性气体保护焊 | Welding and allied processes - Joint preparation - Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys |
| BS HC 100-1972 | 铁、镍、铜、钴和难熔金属基合金铸件的检验和试验程序 | Inspection and testing procedure for iron, nickel, copper, cobalt and refractory metal base alloy castings |
| BS HC 202-1973 | 沉淀硬化镍基铬-铌-钼-铁-钨合金铸件规范(铬20.0、铌6.6、钼6.0、铁3.0、钨2.5) | Specification for precipitation hardening nickel base chromium-niobium-molybdenum-iron-tungsten alloy castings (Cr 20.0, Nb 6.6, Mo 6.0, Fe 3.0, W 2.5) |
| BS HC 205-1974 | 沉淀硬化镍基铬-钴-钼-钛合金铸件规范(铬20、钴20、钼6、钛2 | Specification for precipitation hardening nickel base chromium-cobalt-molybdenum-titanium alloy castings (Cr 20, Co 20, Mo 6, Ti 2) |
| BS HC 206-1975 | 沉淀硬化镍基铬-钴-钼-钛合金精密铸件规范(铬20、钴20、钼6、钛2) | Specification for precipitation hardening nickel base chromium-cobalt-molybdenum-titanium alloy precision castings (Cr 20, Co 20, Mo 6, Ti 2) |
| BS HC 3-1973 | 1%铬钼低合金钢铸件(700牛顿/平方毫米)规范 | Specification for 1% chromium-molybdenum low alloy steel castings (700 N/mm2) |
| BS HC 301-1973 | 钴基铬-镍-钨合金铸件规范(铬25.5、镍10.5、钨7.5) | Specification for cobalt base chromium-nickel-tungsten alloy castings (Cr 25.5, Ni 10.5. W 7.5) |
| BS HC 403-1977 | 高铬合金铸件铁环形坩埚规范(离心铸造)(适用于直径达400mm的活塞环) | Specification for high chromium alloy cast iron ring pots (centrifugally cast) (suitable for piston rings up to 400 mm in diameter) |
| BS HC 404-1977 | 铬-钼合金铸件铁环形坩埚(适用于离心铸造和砂型铸造密封环、活塞环和汽缸套筒) | Specification for chromium-molybdenum alloy cast iron ring pots (suitable for centrifugally cast and sand cast sealing rings, piston rings and cylinder liners) |
| BS HC 502-1981 | 铜基铝-镍-铁合金铸件规范(620MPa)(铝9.5、镍5、铁5) | Specification for copper base aluminium-nickel-iron alloy castings (620 MPa) (Al 9.5, Ni 5, Fe 5) |
| BS HR 10-1972 | 镍-钴-铬-钼-钛-铝耐合金坯锭、棒材、锻件和零件(镍基、Co20、Cr20、Mo5.9、Ti2.1、Al0.5)规范 | Specification for nickel-cobalt-chromium-molybdenum-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (nickel base, Co 20, Cr 20, Mo 5.9, Ti 2.1, Al 0.5) |
| BS HR 203-1972 | 镍-铬-钛耐热合金薄板材、薄板材和带材(镍基、Cr19.5、Ti0.4)规范 | Specification for nickel-chromium-titanium heat-resisting alloy plate, sheet and strip (nickel base, Cr 19.5, Ti 0.4) |
| BS HR 204-1972 | 镍-铬-铁-钼-钴-钨耐热合金板材,薄板材和带材(镍基、Cr22、Fe18.5、Mo9、Co1.5、W0.6)规范 | Specification for nickel-chromium-iron-molybdenum-cobalt-tungsten heat-resisting alloy plate, sheet and strip (nickel base Cr 22, Fe 18.5, Mo 9, Co 1.5, W 0.6) |
| BS HR 205-1989 | 镍铜合金薄板材和带材:退火的(镍基、Cu31)规范 | Nickel-copper alloy sheet and strip: annealed (Nickel base, Cu 31) |
| BS HR 206-1973 | 镍-钴-铬-钼-钛-铝耐热合金板材、薄板材和带材(镍基、Co20、Cr20、Mo5.9、Ti2.1、Al0.5)规范 | Specification for nickel-cobalt-chromium-molybdenum-titanium-aluminium heat-resisting alloy plate, sheet and strip (nickel base, Co 20, Cr 20, Mo 5.9, Ti 2.1, Al 0.5) |
| BS HR 207-1973 | 镍-铁-铬-钼-铝-钛耐热合金板材、薄板材和带材(Ni/Co43.5、Cr16.5、Mo3.3、Al1.2、Ti1.2、Fe余量)规范 | Specification for nickel-iron-chromium-molybdenum-aluminium-titanium heat-resisting alloy plate, sheet and strip (Ni/Co 43.5, Cr 16.5, Mo 3.3, Al 1.2, Ti 1.2, Fe remainder) |
| BS HR 208-1989 | 镍铬铁合金薄板材、带材和板材规范:退火的(镍基、Cr15.5、Fe8) | Specification for nickel-chromium-iron alloy sheet, strip and plate: annealed (Nickel base, Cr 15.5, Fe 8) |
| BS HR 209-1989 | 镍-铬-钴-钼-钛-铝耐热合金薄板材、带材和板材:软化的(镍基、Cr18、Co14、 Mo7、Ti2.2、Al2.1)规范 | Specification for nickel-chromium-cobalt-molybdenum-titanium-aluminium heat-resisting alloy sheet, strip and plate: softened (nickel base, Cr 18, Co 14, Mo 7, Ti 2.2, Al 2.1) |
| BS HR 240-1972 | 钴-铬-钨-镍-锰耐热合金板材、薄板材和带材(钴基、Cr20、W15、Ni10、Mn1.5)规范 | Specification for cobalt-chromium-tungsten-nickel-manganese heat-resisting alloy plate, sheet and strip (cobalt base Cr 20, W 15 , Ni 10, Mn 1.5) |
| BS HR 3-1972 | 镍-钴-铬-钼-钛-铝耐热合金坯锭、棒材、锻件和零件(镍基、Co20、Cr14.8、Mo05、Al4.7、Ti1.2)规范 | Specification for nickel-cobalt-chromium-molybdenum-aluminium-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Co 20, Cr 14.8 , Mo 5, Al 4.7, Ti 1.2) |
| BS HR 4-1972 | 镍-铬-钴-铝-钼-钛耐热合金坯锭、棒材、锻件和零件(镍基、Cr15、Co14.2、Al5、Mo 4、Ti4)规范 | Specification for nickel-chromium-cobalt-aluminium-molybdenum-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 15, Co 14.2 , Al 5, Mo 4, Ti 4) |
| BS HR 40-1972 | 钴-铬-钨-镍-锰耐合金坯锭、棒材、锻件和零件(镍基、Cr20、W15、Ni10、Mn1.5)规范 | Specification for cobalt-chromium-tungsten-nickel-manganese heat-resisting alloy billets, bars and forgings (cobalt base, Cr 20, W 15, Ni 10, Mn 1.5) |
| BS HR 402-1973 | 冷加工和软化的无缝镍铬钴钛铝耐热合金管(镍基、Cr19.5、Co18.0、Ti2.5、Al1.5)规范 | Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy cold worked and softened seamless tubes (nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5) |
| BS HR 403-1973 | 冷加工和软化的无缝镍铬钛耐热合金管(镍基、Cr19.5、Ti0.4)规范 | Specification for nickel-chromium-titanium heat-resisting alloy cold-worked and softened seamless tubes (nickel base, Cr 19.5, Ti 0.4) |
| BS HR 404-1973 | 冷加工溶液处理的无缝镍钴铬钼钛铝耐热合金管(镍基、Co20、Cr20、Mo5.9、Ti2.1、Al0.5)规范 | Specification for nickel-cobalt-chromium-molybdenum-titanium-aluminium heat-resisting alloy cold worked solution treated seamless tubes (nickel base, Co 20, Cr 20, Mo 5.9, Ti 2.1, Al 0.5) |
| BS HR 5-1972 | 镍-铬-钛耐热合金坯锭、棒材、锻件和零件(镍基、Cr19.5、Ti0.4)规范 | Specification for nickel-chromium-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 19.5, Ti 0.4) |
| BS HR 505-1981 | 螺纹垫圈(最大直径2mm)用镍铬铁钛铌铝耐热合金圆线材(镍基、Cr15.5、Fe7.0、Ti2.5、N6/Ta0.95、Al0.70)规范 | Specification for nickel-chromium-iron-titanium-niobium-aluminium heat-resisting alloy round wire for thread inserts (maximum diameter 2 mm) (nickel base, Cr 15.5, Fe 7.0, Ti 2.5, Nb/Ta 0.95, Al 0.70) |
| BS HR 506-1989 | 镍-铬-钴-钛-铝耐热合金线材:软化的(镍基、Cr19.5、Co1.8、Ti2.5、Al1.5)规范 | Nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy wire: softened (Nickel base, Cr 19.5, Co 18, Ti 2.5, Al 1.5) |
| BS HR 51-1973 | 耐热合金坯锭、棒材、锻件和零件(Ni25.5、Cr14.7、Ti2、Mn1.5、Mo1.2、Si0.7、V0.3、Fe余量)规范 | Specification for heat-resisting alloy billets, bars, forgings and parts (Ni 25.5, Cr 14.7, Ti 2, Mn 1.5, Mo 1.2, Si 0.7, V 0.3, Fe remainder) |
| BS HR 52-1973 | 耐热合金坯锭、棒材、锻件和零件(Ni25.5、Cr14.7、Ti1.8、Mn1.5、Mo1.2、V0.3、Fe余量)规范 | Specification for heat-resisting alloy billets, bars, forgings and parts (Ni 25.5, Cr 14.7, Ti 1.8, Mn 1.5, Mo 1.2, V 0.3, Fe remainder) |
| BS HR 53-1973 | 耐热合金坯锭、棒材、锻件和；零件(Ni/Co42.5、Cr12.5、Mo5.8、Ti3.0、Fe余量)规范 | Specification for nickel-iron-chromium-molybdenum-titanium heat-resisting alloy billets, bars, forgings and parts (Ni/Co 42.5, Cr 12.5, Mo 5.8, Ti 3.0, Fe remainder) |
| BS HR 55-1980 | 镍-铁-铬-钼-铝-钛耐热合金坯锭、棒材、锻件和部件(Ni/Co43.5、Cr16.5、Mo3.3、 Al1.2、Ti1.2、Fe 剩余量) | Specification for nickel-iron-chromium-molybdenum-aluminium-titanium heat-resisting alloy billets, bars, forgings and parts (Ni/Co 43.5, Cr 16.5, Mo 3.3 , Al 1.2, Ti 1.2, Fe remainder) |
| BS HR 6-1972 | 镍-铬-铁-钼-钴-钨耐合金坯锭、棒材、锻件和零件(镍基、Cr21.7、Fe18.5、Mo9、Co1.5、W0.6)规范 | Specification for nickel-chromium-iron-molybdenum-cobalt-tungsten heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 21.7, Fe 18.5, Mo 9, Co 1.5, W 0.6) |
| BS ISO 10270-1996 | 金属和合金的腐蚀.核动力反应堆用锆合金的耐水腐蚀试验 | Corrosion of metals and alloys - Aqueous corrosion testing of zirconium alloys for use in nuclear power reactors |
| BS ISO 10713-1997 | 珠宝.金合金涂层 | Jewellery - Gold alloy coatings |
| BS ISO 11303-2002 | 金属和合金的腐蚀.防大气腐蚀保护方法的选择指南 | Corrosion of metals and alloys - Guidelines for selection of protection methods against atmospheric corrosion |
| BS ISO 11438-1-1994 | 镍铁合金.采用电热原子吸收光谱测定法对微量元素含量的测定.第1部分:一般要求和试样溶解 | Ferronickel - Determination of trace-element content by electrothermal atomic absorption spectrometric method - General requirements and sample dissolution |
| BS ISO 11438-2-1994 | 镍铁合金.采用电热原子吸收光谱测定法对微量元素含量的测定.第2部分: 铅含量测定 | Ferronickel - Determination of trace-element content by electrothermal atomic absorption spectrometric method - Determination of lead content |
| BS ISO 11438-3-1994 | 镍铁合金.采用电热原子吸收光谱测定法对微量元素含量的测定.第3部分: 锑含量测定 | Ferronickel - Determination of trace-element content by electrothermal atomic absorption spectrometric method - Determination of antimony content |
| BS ISO 11438-4-1994 | 镍铁合金.采用电热原子吸收光谱测定法对微量元素含量的测定.第4部分: 锡含量测定 | Ferronickel - Determination of trace-element content by electrothermal atomic absorption spectrometric method - Determination of tin content |
| BS ISO 11438-5-1994 | 镍铁合金.采用电热原子吸收光谱测定法对微量元素含量的测定.第5部分:碲含量测定 | Ferronickel - Determination of trace-element content by electrothermal atomic absorption spectrometric method - Determination of tellurium content |
| BS ISO 11438-6-1994 | 镍铁合金.采用电热原子吸收光谱测定法对微量元素含量的测定.第6部分:铊含量测定 | Ferronickel - Determination of trace-element content by electrothermal atomic absorption spectrometric method - Determination of thallium content |
| BS ISO 11438-7-1994 | 镍铁合金.采用电热原子吸收光谱测定法对微量元素含量的测定.第7部分:银含量测定 | Ferronickel - Determination of trace-element content by electrothermal atomic absorption spectrometric method - Determination of silver content |
| BS ISO 11438-8-1994 | 镍铁合金.采用电热原子吸收光谱测定法对微量元素含量的测定.铟含量的测定 | Ferronickel - Determination of trace-element content by electrothermal atomic absorption spectrometric method - Determination of indium content |
| BS ISO 11463-1996 | 金属与合金的腐蚀.麻点腐蚀的评估 | Corrosion of metals and alloys - Evaluation of pitting corrosion |
| BS ISO 11782-1-1998 | 金属和合金的腐蚀.腐蚀疲劳试验.失效试验周期 | Corrosion of metal and alloys - Corrosion fatigue testing - Cycles to failure testing |
| BS ISO 11782-2-1998 | 金属合合金的腐蚀.腐蚀疲劳试验.采用预开裂样品的裂纹扩展试验 | Corrosion of metal and alloys - Corrosion fatigue testing - Crack propagation testing using precracked specimens |
| BS ISO 11844-1-2006 | 金属与合金的腐蚀.室内空气低腐蚀性分类.室内腐蚀性的测定和评估 | Corrosion of metals and alloys - Classification of low corrosivity of indoor atmospheres - Determination and estimation of indoor corrosivity |
| BS ISO 11844-2-2006 | 金属与合金的腐蚀.室内空气低腐蚀性分类.室内空气中腐蚀作用的测定 | Corrosion of metals and alloys - Classification of low corrosivity of indoor atmospheres - Determination of corrosion attack in indoor atmospheres |
| BS ISO 11844-3-2006 | 金属与合金的腐蚀.室内空气低腐蚀性分类.室内腐蚀作用下环境参数的测定 | Corrosion of metals and alloys - Classification of low corrosivity of indoor atmospheres - Measurement of environmental parameters affecting indoor corrosivity |
| BS ISO 11846-1996 | 金属和合金的腐蚀.可溶液热处理的铝合金抗颗粒间腐蚀的测定 | Corrosion of metals and alloys - Determination of resistance to intergranular corrosion of solution heat-treatable aluminium alloys |
| BS ISO 11873-2005 | 硬质合金.钴金属粉末中硫和碳含量的测定.红外线探测法 | Hardmetals - Determination of sulfur and carbon contents in cobalt metal powders - Infrared detection method |
| BS ISO 12732-2006 | 金属和合金腐蚀.利用双环网络法进行电化学电动势活化测量 | Corrosion of metals and alloys - Electrochemical potentiokinetic reactivation measurement using the double loop method (based on Cihal's method) |
| BS ISO 13583-1-2001 | 离心铸造钢和合金制品.一般试验和公差 | Centrifugally cast steel and alloy products - General testing and tolerances |
| BS ISO 13583-2-2003 | 离心铸造钢及合金产品.耐热材料 | Centrifugally cast steel and alloy products - Heat resistant materials |
| BS ISO 13756-1998 | 银制珠宝合金用银的测定.采用氯化钠或氯化钾的容量方法(电势测定法) | Determination of silver in silver jewellery alloys - Volumetric (potentiometric) method using sodium chloride or potassium chloride |
| BS ISO 13899-2-2005 | 钢.合金钢中Mo、Nb和W含量的测定.感应耦合等离子体原子发射光谱法.Nb含量的测定 | Steel - Determination of Mo, Nb and W contents in alloyed steel - Inductively coupled plasma atomic emission spectrometric method - Determination of Nb Content |
| BS ISO 14788-2005 | 连续热浸镀锌5%铝合金涂层钢薄板 | Continuous hot-dip zinc-5% aluminium alloy coated steel sheet |
| BS ISO 15324-2001 | 金属和合金的腐蚀.采用滴水蒸发试验对应力腐蚀裂纹的评估 | Corrosion of metals and alloys - Evaluation of stress corrosion cracking by the drop evaporation test |
| BS ISO 15329-2006 | 金属和合金的腐蚀.热处理铝合金的粒间腐蚀易感性评价的阳极试验 | Corrosion of metals and alloys - Anodic test for evaluation of intergranular corrosion susceptibility of heat-treatable aluminium alloys |
| BS ISO 16151-2006 | 金属和合金的腐蚀.干和湿条件下曝露于酸性盐喷雾中的加速循环试验 | Corrosion of metals and alloys - Accelerated cyclic tests with exposureto acidified salt spray, "dry" and "wet" conditions |
| BS ISO 16220-2005 | 镁和镁合金.镁合金铸锭和铸件 | Magnesium and magnesium alloys - Magnesium alloy ingots and castings |
| BS ISO 16468-2005 | 熔模铸件(钢、镍合金和钴合金).一般技术要求 | Investment castings (steel,nickel alloys and cobalt alloys) - General technical requirements |
| BS ISO 16701-2003 | 金属及合金的腐蚀.调节空气中的腐蚀.暴露于间歇喷洒盐溶液和潮湿循环受控环境下的加速腐蚀试验 | Corrosion of metals and alloys - Corrosion in artificial atmosphere - Accelerated corrosion test involving exposure under controlled conditions of humidity cycling and intermittent spraying of a salt solution |
| BS ISO 16784-1-2006 | 金属与合金的腐蚀.工业冷却水系统中的腐蚀性和污垢.开放式循环冷却水系统的污垢控制添加剂和执行腐蚀性实验 | Corrosion of metals and alloys - Corrosion and fouling in industrial cooling water systems - Guidelines for conducting pilot-scale evaluation of corrosion and fouling control additives for open recirculating cooling water systems |
| BS ISO 16784-2-2006 | 金属及合金的腐蚀.工业冷却水系统的腐蚀性和结污.用操纵管路试验装置评估冷却水处理程序性能 | Corrosion of metals and alloys - Corrosion and fouling in industrial cooling water systems - Evaluation of the performance of cooling water treatment programmes using a pilot-scale test rig |
| BS ISO 17475-2006 | 金属和合金的腐蚀.电化学试验方法.恒电势的和动态电势的偏振测量导则 | Corrosion of metals and alloys - Electrochemical test methods - Guidelines for conducting potentiostatic and potentiodynamic polarization measurements |
| BS ISO 17615-2007 | 铝和铝合金.重熔用合金铸锭.规范 | Aluminium and aluminium alloys - Alloyed ingots for remelting - Specifications |
| BS ISO 17864-2006 | 金属和合金的腐蚀性.静电位控制下的临界点蚀温度测定 | Corrosion of metals and alloys - Determination of the critical pitting temperature under potentiostatic control |
| BS ISO 19959-2005 | 熔模铸件表面情况的外观检验.钢、镍合金和钴合金 | Visual examination of the surface condition of investment castings - Steel, nickel alloys and cobalt alloys |
| BS ISO 19960-2005 | 有特殊物理性能的铸钢和合金 | Cast steels and alloys with special physical properties |
| BS ISO 20552-2007 | 工作场所空气.汞蒸气的测定.金汞合金收集的方法和使用原子吸收光谱法或原子荧光光谱法的分析法 | Workplace air - Determination of mercury vapour - Method using gold-amalgam collection and analysis by atomic absorption spectrometry or atomic fluorescence spectrometry |
| BS ISO 20703-2007 | 储气瓶.可再填充的焊接铝合金气瓶.设计、结构和试验 | Gas cylinders - Refillable welded aluminium-alloy cylinders - Design, construction and testing |
| BS ISO 209-2007 | 铝和铝合金.化学成分 | Aluminium and aluminium alloys - Chemical composition |
| BS ISO 23079-2005 | 镁和镁合金.回炉料.要求、分类和验收 | Magnesium and magnesium alloys - Returns - Requirements, classification and acceptance |
| BS ISO 3116-2007 | 镁和镁合金.锻造镁合金 | Magnesium and magnesium alloys - Wrought magnesium alloys |
| BS ISO 3160-1-1999 | 表壳和附件.金合金覆盖层.第1部分:一般要求 | Watch-cases and accessories - Gold alloy coverings - General requirements |
| BS ISO 3160-2-2003 | 表壳和附件.金合金覆盖层.纯度、厚度、耐腐蚀性能和结合强度的测定 | Watch-cases and accessories - Gold alloy coverings - Determination of fineness, thickness, corrosion resistance and adhesion |
| BS ISO 3928-1999 | 不包括硬质合金的烧结金属材料.疲劳试件 | Sintered metal materials, excluding hardmetals - Fatigue test pieces |
| BS ISO 4381-2000 | 普通轴承.多层普通轴承用铅锡铸造合金 | Plain bearings - Lead and tin casting alloys for multilayer plain bearings |
| BS ISO 4384-1-2000 | 普通轴承.轴承合金的硬度试验.复合材料 | Plain bearings - Hardness testing of bearing metals - Compound materials |
| BS ISO 4498-2005 | 不包括硬质合金的烧结金属材料.表观硬度和显微硬度的测定 | Sintered metal materials, excluding hardmetals - Determination of apparent hardness and microhardness |
| BS ISO 4524-2-2000 | 金属镀层.金及金合金电镀层的试验方法.混合流动气体(MFG)环境试验 | Metallic coatings - Test methods for electrodeposited gold and gold alloy coatings - Mixed flowing gas (MFG) environmental tests |
| BS ISO 4999-2006 | 商品级和冲压和结构级连续热镀锡(合金)冷轧碳素薄钢板 | Continuous hot-dip terne (lead alloy) coated cold-reduced carbon steel sheet of commercial, drawing and structural qualities |
| BS ISO 5468-2006 | 带硬质合金钻头的旋转和旋转冲击式砖石砌工钻.尺寸. | Rotary and rotary impact masonry drill bits with hardmetal tips - Dimensions |
| BS ISO 6305-2-2007 | 铁道部件.技术交货要求.非合金碳钢垫板 | Railway components - Technical delivery requirements - Non-alloy carbon steel baseplates |
| BS ISO 6978-2-2003 | 天然气.汞的测定.用金/铂合金混汞法对汞的采样 | Natural gas - Determination of mercury - Sampling of mercury by amalgamation on gold/platinum alloy |
| BS ISO 7141-2005 | 道路车辆.轻合金轮.碰撞试验 | Road vehicles - Light alloy wheels - Impact test |
| BS ISO 7539-8-2000 | 金属和合金的腐蚀.应力腐蚀试验.焊件评定用试样的制备和使用 | Corrosion of metals and alloys - Stress corrosion testing - Preparation and use of specimens to evaluate weldments |
| BS ISO 7539-9-2003 | 金属和合金的腐蚀.应力腐蚀试验.在加大荷载或加大位移条件下试验用预裂样品的制备和使用 | Corrosion of metals and alloys - Stress corrosion testing - Preparation and use of pre-cracked specimens for tests under rising load or rising displacement |
| BS ISO 7989-2-2007 | 钢丝和钢丝制品.钢丝的有色金属涂层.锌或锌合金涂覆 | Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Zinc or zinc-alloy coating |
| BS L 103-1971 | 铝-铜(4.4)-镁(0.8)-硅(0.7)-锰(0.8)合金锻坯和锻件规范(固溶处理和室温时效) | Specification for forging stock and forgings of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) |
| BS L 105-1971 | 铝-铜(4.4)-镁(0.5)-硅(0.7)-锰(0.8)合金管材规范(固溶处理和室温效)(壁厚度小于10mm) | Specification for tube of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and aged at room temperature) (not exceeding 10 mm wall thickness) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) |
| BS L 109-1971 | 铝-铜(4.4)-镁(1.5)-锰(0.6)合金铝涂层薄板和带材规范(溶液处理和室温时效) | Specification for aluminium-coated sheet and strip of aluminium-copper-magnesium-manganese alloy (solution treated and aged at room temperature) (Cu 4.4, Mg 1.5, Mn 0.6) |
| BS L 110-1971 | 铝-铜(4.4)-镁(1.5)-锰(0.6)合金铝涂层薄板材和带材规范(由用户进行溶液处理) | Specification for aluminium-coated sheet and strip of aluminium-copper-magnesium-manganese alloy (supplied for solution treatment by the user) (Cu 4.4, Mg 1.5, Mn 0.6) |
| BS L 112-1971 | 铝-镁(0.8)-硅(1)-锰(0.7)合金锻坯和锻件规范(溶液处理和沉淀处理)(适用于焊接) | Specification for forging stock and forgings of aluminium-magnesium-silicon-manganese alloy (solution treated and precipitation treated) (suitable for welding) (Mg 0.8, Si 1, Mn 0.7) |
| BS L 113-1971 | 铝-镁(0.8)-硅(1)-锰(0.7)合金薄板材和带材规范(溶液处理和沉淀处理)(适用于焊接) | Specification for sheet and strip of aluminium-magnesium-silicon-manganese alloy (solution treated and precipitation treated) (suitable for welding) (Mg 0.8, Si 1, Mn 0.7) |
| BS L 114-1971 | 铝-镁(0.8)硅(1)-锰(0.7)合金管规范(溶液处理和沉淀处理)(壁厚度小于10mm)(适用于焊接) | Specification for tube of aluminium-magnesium-silicon-manganese alloy (solution treated and precipitation treated) (not exceeding 10 mm wall thickness) (suitable for welding) (Mg 0.8, Si 1, Mn 0.7) |
| BS L 115-1971 | 铝-镁(0.8)硅(1)-锰(0.7)合金板规范(溶液处理,拉伸控制及沉淀处理)(厚度小于25mm)(适用于焊接) | Specification for plate of aluminium-magnesium-silicon-manganese alloy (solution treated, controlled stretched and precipitation treated) (not exceeding 25 mm thickness) (suitable for welding) (Mg 0.8, Si 1, Mn 0.7) |
| BS L 117-1975 | 铝-镁(1.0)-硅(0.6)-铜(0.28)-铬(0.2)合金管规范(溶液处理和人工时效:未经液压试验)(厚度小于10mm) | Specification for tube of aluminium-magnesium-silicon-copper-chromium alloy (solution treated and artificially aged: not tested hydraulically) (not exceeding 10 mm thickness) (Mg 1.0, Si 0.6, Cu 0.28, Cr 0.2) |
| BS L 118-1975 | 铝-镁(1.0)-硅(0.6)-铜(0.28)-铬(0.2)合金管规范(溶液处理和人工时效:液压试验)(壁厚度小于10mm) | Specification for tube of aluminium-magnesium-silicon-copper-chromium alloy (solution treated and artificially aged: tested hydraulically) (not exceeding 10 mm thickness) (Mg 1.0, Si 0.6, Cu 0.28, Cr 0.2) |
| BS L 119-1975 | 铝-铜(5.0)-镍(1.5)-锰(0.5)-钛(0.2)-锆(0.2)-钴(0.2)-锑(0.2)合金铸锭和铸件规范(溶液处理和人工时效) | Specification for ingots and castings of aluminium-copper-nickel-manganese-titanium-zirconium-cobalt-antimony alloy (solution treated and artificially aged) (Cu 5.0, Ni 1.5, Mn 0.25, Ti 0.2, Zr 0.2, Co 0.2, Sb 0.2) |
| BS L 154-1977 | 铝-铜(4)-硅(1)合金铸锭和铸件规范(溶液处理和室温时效) | Specification for ingots and castings of aluminium-copper-silicon alloy (solution treated and aged at room temperature) (Cu 4, Si 1) |
| BS L 155-1977 | 铝-铜(4)-硅(1)合金铸锭和铸件规范(溶液处理和人工时效) | Specification for ingots and castings of aluminium-copper-silicon alloy (solution treated and artificially aged) (Cu 4, Si 1) |
| BS L 158-1978 | 铝-铜(4.4)-镁(0.5)-硅(0.8)-锰(0.8)合金紧公差薄板材和带材规范(溶液处理和室温时效) | Specification for close toleranced sheet and strip of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8) |
| BS L 159-1978 | 铝-铜(4.4)-镁(0.5)-硅(0.8)-锰(0.8)合金紧公差薄板材和带材规范(溶液处理和人工时效) | Specification for close toleranced sheet and strip of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8) |
| BS L 161-1976 | 规范.铝-锌(5.6)-镁(2.5)-铜(1.6)-锆(0.22)合金手工锻件和模压锻件(溶液处理和人工时效至过老化条件) | Specification - Hand and die forgings of aluminium-zinc-magnesium-copper-chromium alloy (solution treated and artificially aged to an overaged condition) (Zn 5.6, Mg 2.5, Cu 1.6, Cr 0.22) |
| BS L 162-1976 | 规范.铝-锌(5.6)-镁(2.5)-铜(1.6)-铬(0.22)合金冷压手工锻件(溶液处理和人工时效至过老化条件) | Specification - Cold compressed hand forgings of aluminium-zinc-magnesium-copper-chromium alloy (solution treated and artificially aged to an overaged condition) (Zn 5.6, Mg 2.5, Cu 1.6, Cr 0.22) |
| BS L 163-1978 | 铝涂层铝-铜(4.4)-镁(0.5)-硅(0.8)-锰(0.8)合金薄板材和带材规范(溶液处理、冷加工压平和室温时效) | Specification for sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated , cold worked for flattening and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8) |
| BS L 164-1978 | 铝涂层铝-铜(4.4)-镁(0.5)-硅(0.8)-锰(0.8)合金薄板材和带材规范(固溶处理和室温时效的) | Specification for sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8) |
| BS L 165-1978 | 铝涂层铝-铜(4.4)-镁(0.5)-硅(0.8)-锰(0.8)合金薄板材和带材规范(固溶处理和人工时效的) | Specification for sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8) |
| BS L 166-1978 | 铝涂层铝-铜(4.4)-镁(0.5)-硅(0.8)-锰(0.8)合金紧公差薄板材和带材规范(溶液处理和室温时效) | Specification for close toleranced sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8) |
| BS L 167-1978 | 铝-镀铝-铜(4.4)-镁(0.5)-硅(0.8)-锰合金紧公差薄板材和带材规范(固溶处理和人工时效的) | Specification for close toleranced sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8) |
| BS L 168-1978 | 铝-铜(4.4)-镁(0.5)-硅(0.7)-锰(0.8)合金棒材和挤压型材规范(固溶处理和人工时效)(直径不超过200mm或较小的 | Specification for bars and extruded sections of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (not exceeding 200 mm diameter or minor sectional dimension) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) |
| BS L 169-1986 | 铝-硅(7)-镁(0.6)合金铸锭和铸件规范(溶液处理和人工时效) | Specification for ingots and castings of aluminium-silicon-magnesium alloy (solution treated and artificially aged) (Si 7, Mg 0.6) |
| BS L 170-1989 | 铝-锌(5.6)-镁(2.5)-铜(1.6)-铬(0.23)合金挤压棒材和型材规范(溶液处理和控制拉伸和人工时效)(直径或较小截 | Specification for extruded bars and sections of aluminium-zinc-copper-chromium alloy (solution treated, controlled stretched and artificially aged) (not exceeding 150 mm diameter or minor sectional dimension) (Zn 5.6, Mg 2.5, Cu 1.6, Cr 0.23) (7075) |
| BS L 171-1990 | 铝-锌(5.7)-镁(2.5)-锰(0.5)-铜(0.5)合金锻件规范(锻件或经过退火随后热处理锻件)(直径或较小截面尺寸小于1 | Specification for forging of aluminium-zinc-magnesium-manganese-copper alloy (supplied as-forged or annealed for subsequent heat treatment) (not exceeding 150 mm diameter or minor sectional dimension) (Zn 5.7, Mg 2.7, Mn 0.5, Cu 0.5) (7014) |
| BS L 172-1989 | 铝-锌-镁-锰-铜合金挤压、轧制或锻坯规范(BS L 171锻件制造用)(Zn5.7、Mg2.7、Mn0.5、Cu0.5)(7014) | Specification for extruded, rolled or cast forging stock of aluminium-zinc-magnesium-manganese-copper alloy (for manufacture of forgings to BS L 171) (Zn 5.7, Mg 2.7, Mn 0.5, Cu 0.5) (7014) |
| BS L 173-1991 | 冷铸用铝-硅-镁合金铸件规范.(过量条件下溶液处理和沉淀处理(T7)) | Specification for castings of aluminium-silicon-magnesium alloy, chill cast (solution treated and precipitation treated to an overaged (T7) condition) |
| BS L 174-1991 | 砂型铸造用铝-硅-镁合金铸件规范(过量条件下溶液处理和沉淀处理(T7)) | Specification for castings of aluminium-silicon-magnesium alloy, sand cast (solution treated and precipitation treated to an overaged (T7) condition) |
| BS L 512-1973 | 镁-铝(6.0)-锌(1.0)合金棒材和挤压型材规范(直径不超过150mm或较小截面尺寸) | Specification for bars and extruded sections of magnesium-6% aluminium-zinc alloy (not exceeding 150 mm diameter or minor sectional dimension) (Al 6.0, Zn 1.0) |
| BS L 513-1973 | 镁-铝(6.0)-锌(1.0)合金锻坯和锻件规范 | Specification for forging stock and forgings of magnesium-6% aluminium-zinc alloy (Al 6.0, Zn 1.0) |
| BS L 514-1973 | 镁--锌(3.0)－锆(0.6)合金锻坯和锻件规范 | Specification for forging stock and forgings of magnesium-3% zinc-zirconium alloy (Zn 3.0, Zr 0.6) |
| BS L 515-1973 | 镁--锌(1.25)-锆（0.6）合金锻坯和锻件规范 | Specification for sheet and strip of magnesium-11/4% zinc-zirconium alloy (suitable for welding by inert-gas shielded arc techniques) (Zn 1.25, Zr 0.6) |
| BS M 58-1986 | 采用硫酸处理工艺的钛和钛合金阳极涂层规范 | Specification for anodic coating of titanium and titanium alloys by the sulphuric acid process |
| BS M 93-2005 | 富镁合金的防腐蚀保护.规范 | Protection of magnesium-rich alloys against corrosion - Specification |
| BS PAS 27-1999 | 承压未增塑聚氯乙烯合金(PVC-A)复合水管和弯管 | Unplasticized poly(vinyl chloride) alloy (PVC-A) pipes and bends for water under pressure |
| BS SP 172-1999 | 铝或铝合金实心铆钉.采购规范 | Rivets, solid, in aluminium or aluminium alloys - Procurement specification |
| BS SP 65-1955 | 航空用铝合金锥形销规范 | Specification for aluminium alloy taper pins for aeronautical purposes |
| BS TA 38-1971 | 机加工用钛-铝-钼-锡-硅-碳合金棒材规范(抗拉强度1250-1420牛顿/平方毫米)(限定控制剖面25mm) | Specification for bar for machining of titanium-aluminium-molybdenum-tin-silicon-carbon alloy (tensile strength 1250-1420 N/mm2) (limiting ruling section 25 mm) |
| BS TA 39-1971 | 钛-铝-钼-锡-硅-碳合金锻坯规范(抗拉强度1250-1420牛顿/平方毫米)(限定控制剖面25mm) | Specification for forging stock of titanium-aluminium-molybdenum-tin-silicon-carbon alloy (tensile strength 1250-1420 N/mm2) (limiting ruling section 25 mm) |
| BS TA 40-1971 | 机加工用钛-铝-钼-锡-硅-碳合金棒材规范(抗拉强度1205-1375牛顿/平方毫米)(限定控制剖面大于25mm,达到并含7 | Specification for bar for machining of titanium-aluminium-molybdenum-tin-silicon-carbon alloy (tensile strength 1205-1375 N/mm2) (limiting ruling section over 25 mm up to and including 75 mm) |
| BS TA 41-1971 | 钛铝钼锡硅碳合金锻坯规范(抗拉强度1205-1375牛顿/平方毫米)(限定控制剖面大于25mm,达到并含75mm) | Specification for forging stock of titanium-aluminium-molybdenum-tin-silicon-carbon alloy (tensile strength 1205-1375 N/mm2) (limiting ruling section over 25 mm up to and including 75 mm) |
| BS TA 42-1971 | 钛-铝-钼-锡-硅-碳合金锻件规范(抗拉强度1205-1375牛顿/平方毫米)(限定控制剖面大于25mm,达到并含75mm) | Specification for forgings of titanium-aluminium-molybdenum-tin-silicon-carbon alloy (tensile strength 1205-1375 N/mm2) (limiting ruling section over 25 mm up to and including 75 mm) |
| BS TA 43-1972 | 钛-铝-锆-钼-硅合金锻坯规范(抗拉强度990-1140牛顿/平方毫米)(限定控制剖面65mm) | Specification for forging stock of titanium-aluminium-zirconium-molybdenum-silicon alloy (tensile strength 990-1140 N/mm2) (limiting ruling section 65 mm) |
| BS TA 44-1972 | 钛-铝-锆-钼-硅合金锻件规范(抗拉强度990-1140牛顿/平方毫米)(限定控制剖面65mm) | Specification for forgings of titanium-aluminium-zirconium-molybdenum-silicon alloy (tensile strength 990-1140 N/mm2) (limiting ruling section 65 mm) |
| BS TA 45-1973 | 机加工用钛铝钼锡硅合金棒材和型材规范(抗拉强度1100-1280 N/mm<上标2>)(限定等圆断面25mm) | Specification for bar and section for machining of titanium-aluminium-molybdenum-tin-silicon alloy (tensile strength 1100-1280 N/mm2) (limiting ruling section 25 mm) |
| BS TA 46-1973 | 机加工用钛铝钼锡硅合金棒材和型材规范(抗拉强度1050-1220 N/mm<上标2>)(限定等圆断面25mm以上100mm以下(含 | Specification for bar and section for machining of titanium-aluminium-molybdenum-tin-silicon alloy (tensile strength 1050-1220 N/mm2) (limiting ruling section over 25 mm up to and including 100 mm) |
| BS TA 47-1973 | 钛铝钼锡硅合金锻坯规范(抗拉强度1050-1220 N/mm<上标2>)(限定等圆断面100mm) | Specification for forging stock of titanium-aluminium-molybdenum-tin-silicon alloy (tensile strength 1050-1220 N/mm2) (limiting ruling section 100 mm) |
| BS TA 48-1973 | 钛铝钼锡硅合金锻件规范(抗拉强度1050-1200 N/mm<上标2>)(限定等圆断面100mm) | Specification for forgings of titanium-aluminium-molybdenum-tin-silicon alloy (tensile strength 1050-1200 N/mm2) (limiting ruling section 100 mm) |
| BS TA 49-1973 | 钛铝钼锡硅合金棒材和型材规范(抗拉强度1000-1200 N/mm<上标2>)(极限等圆截面100mm以上150mm以下(含150mm)) | Specification for bar and section for machining of titanium-aluminium-molybdenum-tin-silicon alloy (tensile strength 1000-1200 N/mm2) (limiting ruling section over 100 mm up to and including 150 mm) |
| BS TA 50-1973 | 钛铝钼锡硅合金锻坯规范(抗拉强度1000-1200 N/mm<上标2>)(限定等圆断面100mm以上150mm以下(含150mm)) | Specification for forging stock of titanium-aluminium-molybdenum-tin-silicon alloy (tensile strength 1000-1200 N/mm2) (limiting ruling section over 100 mm up to and including 150 mm) |
| BS TA 51-1973 | 钛铝钼锡硅合金锻件规范(抗拉强度1000-1200 N/mm<上标2>)(限定等圆断面100mm以上150mm以下(含150mm)) | Specification for forgings of titanium-aluminium-molybdenum-tin-silicon alloy (tensile strength 1000-1200 N/mm2) (limiting ruling section over 100 mm up to and including 150 mm) |
| BS TA 52-1973 | 钛-铜合金板材和带材规范(抗拉强度690-920牛顿/平方毫米) | Specification for sheet and strip of titanium-copper alloy (tensile strength 690-920 N/mm2) |
| BS TA 53-1973 | 机加工用钛-铜合金棒材和型材规范(抗拉强度650-880牛顿/平方毫米)(限定控制剖面75mm) | Specification for bar and section for machining of titanium-copper alloy (tensile strength 650-880 N/mm2) (limiting ruling section 75 mm) |
| BS TA 54-1973 | 钛-铜合金锻坯规范(抗拉强度650-880牛顿/平方毫米)(限定控制剖面75mm) | Specification for forging stock of titanium-copper alloy (tensile strength 650-880 N/mm2) (limiting ruling section 75 mm) |
| BS TA 55-1973 | 钛-铜合金锻件规范(抗拉强度650-880牛顿/平方毫米)(限定控制剖面75mm) | Specification for forgings of titanium-copper alloy (tensile strength 650-880 N/mm2) (limiting ruling section 75 mm) |
| BS TA 56-1974 | 钛-铝-钒合金板材规范(抗拉强度895-1150MPa)(最大厚度100mm) | Specification for plate of titanium-aluminium-vanadium alloy (tensile strength 895-1150 MPa) (maximum thickness 100 mm) |
| BS TA 57-1974 | 钛-铝-钼-锡-硅合金板材规范(抗拉强度1030-1220MPa)(最大厚度65mm) | Specification for plate of titanium-aluminium-molybdenum-tin-silicon alloy (tensile strength 1030-1220 MPa) (maximum thickness 65 mm) |
| BS TA 58-1974 | 钛-铜合金板材规范(抗拉强度520-640MPa)(最大厚度10mm) | Specification for plate of titanium-copper alloy (tensile strength 520-640 MPa) (maximum thickness 10 mm) |
| BS TA 59-1980 | 钛-铝-钒合金板材和带材规范(抗拉强度920-1180MPa) | Specification for sheet and strip of titanium-aluminium-vanadium alloy (tensile strength 920 MPa to 1180 MPa) |
| DD 139-1986 | 锌铝合金锭和铸件规范 | Specification for zinc-aluminium alloy ingots and castings |
| DD ENV 12908-1998 | 铅和铅合金.用火花激发进行发射光谱分析 | Lead and lead alloys. Analysis by optical emission spectrometry (OES) with spark excitation |
| DD ENV 13797-2001 | 腐蚀防护.油和气生产中含硫化氢的环境中使用的碳钢和低合金钢.材料和试验方法.指南 | Corrosion protection. Carbon and low alloy steels for use in hydrogen sulfide containing environments in oil and gas production. Materials and test methods. Guidelines |
| DD ENV 13800-2000 | 铅及铅合金.无铅矩阵分离的火焰原子吸收光谱分析法或感应耦合等离子体辐射光谱(ICP-ES)分析法 | Lead and lead alloys. Analysis by flame atomic absorption spectromerty (FAAS) or inductively coupled plasma emission spectrometry (ICP-ES), without separation of the lead matrix |
| DD ENV 14029-2001 | 铅和铅合金.铅基体分离后火焰原子吸收光谱分析(FAAS)或感应耦合等离子体发射光谱(ICP-ES) | Lead and lead alloys. Analysis by flame atomic absorption spectrometry (FAAS) or inductively coupled plasma emission spectrometry (ICP-ES), after separation of the lead matrix |
| DD ENV 14138-2001 | 铅及铅合金.共沉淀法分离后通过火焰原子吸收光谱法或感应耦合等离子体放射光谱法进行分析 | Lead and lead alloys. Analysis by flame atomic absorption spectrometry (FAAS) or inductively coupled plasma emissions spectrometry (ICP-ES), after separation by co-precipitation |
| DD ENV 1999-1-2-2000 | 欧洲法规9.铝合金结构件的设计.一般规则.结构的防火设计 | Eurocode 9. Design of aluminium structures. General rules. Structural fire design |
| DD ENV 22605-1-1992 | 压力用钢制品.温升参数的导出和证明.第1部分:碳和低合金钢制品的屈服或试验应力 | Steel products for pressure purposes. Derivation and verification of elevated temperature properties. Yield or proof stress of carbon and low alloy steel products |
| FD A45-035-1999 | 钢产品.非合金钢的冷成型板桩.尺寸和剖面性能 | Steel products - Cold-formed sheet piling of non alloy steels - Dimensions and sectional properties. |
| KT 1-1999 | 铝和铝合金 | Aluminium and aluminium alloys |
| PD 6619-1998 | 铜和铜合金.材料登记和材料编号分配用条款与程序 | Copper and copper alloys. Provisions and procedures for the allocation of material numbers and registration of materials |
| PD 6635-1999 | 拉伸和/或冷轧非合金钢棒材.普通棒材,不脱氧低碳钢棒材和不脱氧替代低碳钢棒材与特殊棒材.要求和试验 | Non-alloy steel rod for drawing and/or cold rolling. General purpose rod, rimmed and rimmed substitute low carbon steel rod, rod for special applications. Requirements and tests |
| PD 6641-1999 | 铜及铜合金.成份和产品概要 | Copper and copper alloys. Compendium of compositions and products |
| PD IEC 61394-2001 | 架空线.铝、铝合金和钢裸导线用润滑脂的特性 | Overhead lines. Characteristics of greases for aluminium, aluminium alloy and steel bare conductors |
| 编号 | 中文名称 | 英文名称 |