| 编号 | 中文名称 | 英文名称 |
|---|
| BS 2000-450-2000
| 石油及其制品的试验方法.柴油.用高频往复式装置评定燃油的润滑性.试验方法
| Methods of test for petroleum and its products - Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Test method
|
| BS 3818-1964
| 柴油机车及有轨内燃机车自动密封加油接头规范
| Specification for self-sealing fuelling couplings for diesel locomotives and diesel railcars
|
| BS 6380-1997
| 符合BS EN 590和BS 2869 A2级及D级柴油机燃料和煤气油的低温性能和寒冷气候使用指南
| Guide to low temperature properties and cold weather use of diesel fuels and gas oils conforming to BS EN 590 and classes A2 and D of BS 2869
|
| BS 6680-1985
| 煤矿和其他沼气敏感矿用柴油机防火设备规范
| Specification for flameproof equipment for diesel engines for use in coal mines and other mines susceptible to firedamp
|
| BS AU 141a-1971
| 道路车辆用柴油机性能规范
| Specification for the performance of diesel engines for road vehicles
|
| BS AU 261-1995
| 柴油发动机.60度锥孔的高压喷油管端部连接器
| Diesel engines. High-pressure fuel injection pipe end-connections with 60 female cone
|
| BS CWA 15145-2004
| 机动车燃料.内燃机用柴油乳剂中的水.要求和试验方法
| Automotive fuels - Water in diesel fuel emulsions for use in internal combustion engines - Requirements and test methods
|
| BS DD ISO/TS 23556-2007
| 去除润滑油中柴油机烟灰用装置的性能试验方法.初始过滤效率
| Performance test method for diesel engine soot-removal devices in lubricating oils - Initial filtration efficiency
|
| BS EN 116-1998
| 柴油和家用加热用燃料.冷式过滤器堵塞点的确定
| Diesel and domestic heating fuels - Determination of cold filter plugging point
|
| BS EN 12662-1998
| 石油及其产品的试验方法.液态石油产品.柴油中污染物的测定
| Methods of test for petroleum and its products - Liquid petroleum products - Determination of contamination in middle distillates
|
| BS EN 12827-1999
| 内河航运船只.柴油传送装置用的连接件
| Inland navigation vessels - Connections for the transfer of diesel oil
|
| BS EN 13341-2005
| 家用燃料油、煤油和柴油燃料的地上存储用热塑性固定储油罐.通过阴离子聚合吹塑聚乙烯储油罐、旋转模制聚乙
| Thermoplastics static tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded polyethylene, rotationally moulded polyethylene and polyamide 6 by anionic polymerization tanks - Requirements and test methods
|
| BS EN 14214-2004
| 机动车燃料.柴油发动机用脂肪酸甲脂.要求和试验方法
| Automotive fuels - Fatty acid methylesters (FAME) for diesel engines - Requirements and test methods
|
| BS EN 14274-2003
| 石油及其产品的试验方法.车用燃料.汽油及柴油质量的评估.燃料质量监测系统(FQMS)
| Methods of test for petroleum and its products - Automotive fuels - Assessment of petrol and diesel quality - Fuel quality monitoring system (FQMS)
|
| BS EN 14275-2003
| 车用燃料.汽油及柴油质量的评估.零售点油泵及商业点燃料自动售货机的抽样
| Automotive fuels - Assessment of petrol and diesel fuel quality - Sampling from retail site pumps and commercial site fuel dispensers
|
| BS EN 14530-2004
| 工作场所空气.柴油颗粒物质的测定.一般要求
| Workplace atmospheres - Determination of diesel particulate matter - General requirements
|
| BS EN 590-2004
| 机动车燃料.柴油.要求和试验方法
| Automotive fuels - Diesel - Requirements and test methods
|
| BS EN ISO 12156-1-2006
| 柴油.用高频往复装置(HFRR)进行润滑性能评定.试验方法
| Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Test method
|
| BS EN ISO 13759-1997
| 石油和石油产品的试验方法.石油产品.柴油燃料中硝酸烷基酯的测定.光谱法
| Methods of test for petroleum and its products - Petroleum products - Determination of alkyl nitrate in diesel fuels - Spectrometric method
|
| BS EN ISO 16147-2002
| 小艇.艇内柴油发动机.装在发动机上的燃油和电气元件
| Small craft - Inboard diesel engines - Engine-mounted fuel and electrical components
|
| BS EN ISO 20844-2004
| 石油和相关产品.使用柴油注射器喷嘴测定含聚合物油的剪切稳定性
| Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle
|
| BS EN ISO 21487-2007
| 小艇.永久性安装的汽油和柴油燃油罐
| Small craft - Permanently installed petrol and diesel fuel tanks
|
| BS EN ISO 5165-1998
| 石油产品.柴油点火质量的测定.十六烷发动机法
| Petroleum products - Determination of the ignition quality of diesel fuels - Cetane engine method
|
| BS EN ISO 6246-1998
| 石油产品.轻馏分燃料和柴油燃料的含胶量.喷射蒸发法
| Petroleum products - Gum content of light and middle distillate fuels - Jet evaporation method
|
| BS EN ISO 8861-1998
| 造船.柴油机船舶发动机室的通风.设计要求和计算依据
| Shipbuilding - Engine-room ventilation in diesel-engined ships - Design requirements and basis of calculations
|
| BS ISO 12156-2-2007
| 柴油.用高频往复装置(HFRR)进行润滑油评定.极限值
| Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Limit
|
| BS ISO 12345-2003
| 柴油发动机.燃料喷射设备的清洁度评定
| Diesel engines - Cleanliness assessment of fuel injection equipment
|
| BS ISO 13296-2005
| 柴油发动机.高压燃料喷射管组件.一般要求和尺寸
| Diesel engines - High-pressure fuel injection pipe assemblies - General requirements and dimensions
|
| BS ISO 13555-1-2003
| 柴油发动机.柴油喷注设备动态调速的检查程序.预调节
| Diesel engines - Procedure for checking the dynamic timing of diesel fuel injection equipment - Preconditioning
|
| BS ISO 13555-2-2003
| 柴油机.柴油机喷油系统动态定时的检查程序.试验方法
| Diesel engines - Procedure for checking the dynamic timing of diesel fuel injection equipment - Test method
|
| BS ISO 13555-3-2004
| 柴油发动机.柴油喷射设备动态计时的检验规程.计时设备的验证
| Diesel engines - Procedure for checking the dynamic timing of diesel fuel injection equipment - Validation of timing devices
|
| BS ISO 14681-1998
| 柴油发动机.燃料喷射泵试验.燃料喷嘴的校准
| Diesel engines - Fuel injection pump testing - Calibrating fuel injectors
|
| BS ISO 19438-2004
| 内燃机用柴油燃料和汽油过滤器.用粒子计数和污物滞留量测定过滤效率
| Diesel fuel and petrol filters for internal combustion engines - Filtration efficiency using particle counting and contaminant retention capacity
|
| BS ISO 22241-1-2006
| 柴油发动机.NOx还原剂AUS 32.质量要求
| Diesel engines - NOx reduction agent AUS 32 - Quality requirements
|
| BS ISO 22241-2-2006
| 柴油发动机.NOx还原剂AUS 32.试验方法
| Diesel engines - NOx reduction agent AUS 32 - Test methods
|
| BS ISO 2697-2000
| 柴油发动机.燃料喷嘴."S"尺寸
| Diesel engines - Fuel nozzles - Size "S"
|
| BS ISO 2974-2005
| 柴油机.60°锥孔的高压油管接头管端部连接
| Diesel engines - High-pressure fuel injection pipe end-connections with 60 ° female cone
|
| BS ISO 4010-1998
| 柴油发动机.针栓型滞后校准喷嘴
| Diesel engines - Calibrating nozzle, delay pintle type
|
| BS ISO 4020-2002
| 道路车辆.柴油发动机的燃油滤清器.试验方法
| Road vehicles - Fuel filters for diesel engines.Test methods
|
| BS ISO 4093-2000
| 柴油发动机.喷油泵.试验用高压管
| Diesel engines - Fuel injection pumps - High-pressure pipes for testing
|
| BS ISO 6519-2004
| 柴油机.喷油泵.轴端和毂盘的锥度
| Diesel engines - Fuel injection pumps - Tapers for shaft ends and hubs
|
| BS ISO 7026-1998
| 柴油发动机.S1规格B型针栓式喷嘴的20、21、21.1和27型拧入式喷嘴固定器
| Diesel engines - Screw-in injection nozzle holders, types 20, 21, 21.1 and 27 for pintle nozzle size 'S1' type 'B'
|
| BS ISO 7299-1-2007
| 柴油发动机.泵用端面安装法兰.燃料油喷射泵
| Diesel engines - End-mounting flanges for pumps - Fuel injection pumps
|
| BS ISO 7299-1997
| 柴油发动机.燃油喷射泵用端面安装法兰
| Diesel engines - End-mounting flanges for fuel injection pumps
|
| BS ISO 7612-2006
| 柴油机.共轨燃料喷射系统用基座安装直列式喷油泵和高压供油泵.安装尺寸
| Diesel engines - Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems - Mounting dimensions
|
| BS ISO 7654-1998
| 道路车辆.柴油发动机用离心式燃油过滤器.安装和连接尺寸
| Road vehicles - Spin-on fuel filters for diesel engines - Mounting and connecting dimensions
|
| BS ISO 7879-1998
| 柴油发动机.托架安装直列式燃料喷射泵.安装尺寸
| Diesel engines - Cradle mounted in-line fuel injection pumps - Mounting dimensions
|
| BS ISO 8535-1-2006
| 柴油发动机.高压注射燃油管道用钢管.无缝冷拔单壁管要求
| Diesel engines - Steel tubes for high-pressure fuel injection pipes - Requirements for seamless cold-drawn single-wall tubes
|
| BS ISO 9102-1998
| 柴油发动机.24、25、26和26.1型拧入式喷嘴底座
| Diesel engines - Screw-in injection nozzle holders types 24, 25, 26 and 26.1
|
| 编号 | 中文名称 | 英文名称 |
|---|