| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| A 211-1961 | 飞行器用100°沉头钢螺栓规范(统一螺纹和十字槽)规范 | Specification for 100 countersunk head steel bolts (Unified threads and cruciform recesses) for aircraft |
| BS 10-1962 | 管子、阀门和配件用法兰和螺栓连接规范 | Specification for flanges and bolting for pipes, valves, and fittings |
| BS 1473-1972 | 一般工程用可锻铝和铝合金规范.铆钉、螺栓和螺钉坯料 | Specification for wrought aluminium and aluminium alloys for general engineering purposes - rivet, bolt and screw stock |
| BS 1768-1963 | 统一精密六角头螺栓、螺钉和螺母(UNC与UNF螺纹)规范.标准系列 | Specification for Unified precision hexagon bolts, screws, & nuts (UNC & UNF threads) - Normal series |
| BS 2485-1987 | T形槽、T形螺栓、T形螺母与榫舌规范 | Specification for tee slots, tee bolts, tee nuts and tenons |
| BS 2693-1-1956 | 双头螺栓.第1部分:通用双头螺拴 | Specification for screwed studs - General purpose studs |
| BS 2693-2-1964 | 双头螺栓规范.第2部分:高级双头螺拴(美国标准ASA B1.12 5级干涉配合螺纹)推荐规范 | Specification for screwed studs - Recommendations for high grade studs (with Class 5 interference fit threads to American Standard ASA B1.12) |
| BS 2A 110-1962 | 飞行器用抗剪钢螺栓的钢制螺母(统一六角形和统一螺纹)规范 | Specification for steel nuts (Unified hexagons and Unified threads) for shear bolts for aircraft |
| BS 2A 173-1962 | 飞行器用100°埋头钢螺栓(统一螺纹)规范 | Specification for 100 ° countersunk head steel bolts (Unified threads) for aircraft |
| BS 2A 174-1962 | 飞行器用100°埋头耐腐蚀钢螺栓(统一螺纹)规范 | Specification for 100 ° countersunk head corrosion-resisting steel bolts (Unified threads) for aircraft |
| BS 2A 175-1962 | 飞行器用100°埋头铝合金螺栓(统一螺纹)规范 | Specification for 100 ° countersunk head aluminium alloy bolts (Unified threads) for aircraft |
| BS 2A 229-1972 | 160,000磅力/平方英寸(1100MPa)六角头钢螺栓规范 | Specification for hexagonal head steel bolts 160000 lbf/in2 (1100/MPa) |
| BS 2A 230-1974 | 100°埋头钢螺栓(1100MPa,具有高扭矩高速旋入槽)规范 | Specification for 100 ° countersunk head steel bolts [1100 MPa with Hi-torque speed drive recesses] |
| BS 2A 231-1993 | 螺栓用滚压螺纹.螺纹引导和收尾要求 | Rolled threads for bolts - Lead and runout requirements |
| BS 2A 241-2005 | 拉伸强度为1250MPa(180000 lbf/英寸<上标2>)或更大的突头钢制螺栓的一般要求.规范 | General requirements for steel protruding-head bolts of tensile strength 1250 MPa (180000 lbf/in2) or greater - Specification |
| BS 2A 25-1962 | 飞行器用钢制六角头螺栓(B.A和B.S.F螺纹)规范 | Specification for steel hexagonal-headed bolts (B.A. and B.S.F. threads) for aircraft |
| BS 2A 26-1962 | 飞行器用耐蚀钢六角头螺栓(B.A和B.S.F螺纹)规范 | Specification for corrosion-resisting steel hexagonal-headed bolts (B.A and B.S.F. threads) for aircraft |
| BS 2A 296-1995 | 米制螺栓和螺钉.形位公差 | Bolts and screws, metric - Tolerances of form and position |
| BS 2A 30-1962 | 飞行器用紧公差螺杆的钢制六角头螺栓(B.A和B.S.F螺纹)规范 | Specification for steel hexagonal-headed bolts (B.A. and B.S.F threads) with close tolerance shanks for aircraft |
| BS 2A 57-1962 | 飞行器用钢制六角头抗剪螺栓(B.S.F螺纹)规范 | Specification for steel hexagonal-headed shear bolts (B.S.F. threads) for aircraft |
| BS 2A 58-1962 | 飞行器用抗剪螺栓的钢制六角头螺母(B.S.F螺纹)规范 | Specification for steel hexagonal nuts (B.S.F. threads) for shear bolts for aircraft |
| BS 2A 59-1962 | 飞行器用紧公差螺杆的钢制镀镉六角头螺栓(B.A和B.S.F螺纹)规范 | Specification for cadmium-plated steel hexagonal-headed bolts (B.A. and B.S.F. threads) with close tolerance shanks for aircraft |
| BS 2A 60-1962 | 飞行器用钢制镀镉六角头抗剪螺栓(B.S.F螺纹)规范 | Specification for cadmium-plated steel hexagonal-headed shear bolts (B.S.F. threads) for aircraft |
| BS 2A 61-1962 | 飞行器用铝合金制六角头螺栓(B.A和B.S.F螺纹)规范 | Specification for aluminium alloy hexagonal headed bolts (B.A. and B.S.F. threads) for aircraft |
| BS 2S 116-1964 | 飞机材料规范.机械制造用40号碳素钢光亮冷棒(55-65吨力/平方英寸;限定等圆断面1/4英寸)(主要用于制造螺栓) | Specification for aircraft material - '40' carbon steel bright bars for machining (55-65 tonf/sq in: limiting ruling section 3/4 inch) (primarily intended for the manufacture of machined bolts) |
| BS 2S 147-1976 | 锻制螺栓、螺母用的含0.5%镍-铬-钼钢棒规范 | Specification for 0.5% nickel-chromium-molybdenum steel bars for the manufacture of forged bolts and forged nuts |
| BS 2S 149-1976 | 锻制螺栓、螺母用的含1.75%镍-铬-钼钢棒规范 | Specification for 1.75% nickel-chromium-molybdenum steel bars for the manufacture of forged bolts and forged nuts |
| BS 3454-1995 | 煤矿用的1.9/3.3kV、300A螺栓连接防火电缆连接器和适配器规范(包括380/660V和640/1100V,300A适配器)规范 | Specification for 1.9/3.3 kV, 300 A bolted flameproof cable couplers and adaptors (including 380/660 V and 640/1100 V, 300 A adaptors) for use in coal mines |
| BS 3905-1995 | 煤矿用3.8/6.6 KV、300 A螺栓连接防火电缆连接器和适配器规范 | Specification for 3.8/6.6 kV, 300 A bolted flameproof cable couplers and adaptors, for use in coal mines |
| BS 3A 108-1962 | 飞行器用带紧公差螺杆的钢螺栓(统一六角头和统一螺纹)规范 | Specification for steel bolts (Unified hexagons and Unified threads) with close tolerance shanks for aircraft |
| BS 3A 109-1985 | 钢制抗剪螺栓(统一六角和统一螺纹)规范 | Specification for steel shear bolts (Unified hexagons and Unified threads) |
| BS 3A 116-1962 | 飞行器用盘头钢螺栓(统一螺纹)规范 | Specification for steel pan head bolts (Unified threads) for aircraft |
| BS 3A 117-1962 | 飞行器用盘头耐腐蚀钢螺栓(统一螺纹)规范 | Specification for corrosion-resisting steel pan head bolts (Unified threads) for aircraft |
| BS 3A 171-1962 | 飞行器铝合金盘头螺栓(统一螺纹)规范 | Specification for aluminium alloy pan head bolts (Unified threads) for aircraft |
| BS 3A 212-1993 | 55/65 tonf/in m*m 镀隔钢螺栓(六角形、3A统一螺纹和紧公差螺杆) | Specification for cadmium-plated steel bolts, 55/65 tonf/in2 (Unified hexagons, 3A Unified threads and close tolerance shanks) |
| BS 3S 102-1969 | 碳钼钢(仅供锻造螺栓用的棒材)规范 | Specification for carbon-molybdenum steel (bar for the manufacture of forged bolts only) |
| BS 3S 105-1969 | 碳素钢(仅供锻造螺栓用的棒材)规范 | Specification for carbon steel (bar for the manufacture of forged bolts only) |
| BS 4604-1-1970 | 结构钢制构件高强度摩擦紧固螺栓应用规范,米制系列.第1部分:普通螺拴 | Specification for the use of high strength friction grip bolts in structural steelwork - Metric series - General grade |
| BS 4604-2-1970 | 结构钢制构件中高强度摩擦紧固螺栓应用规范,米制系列.第2部分:高级螺拴(标准杆) | Specification for the use of high strength friction grip bolts in structural steelwork - Metric series - Higher grade (parallel shank) |
| BS 4882-1990 | 法兰和保持压力用螺栓连接规范 | Specification for bolting for flanges and pressure containing purposes |
| BS 4A 100-2003 | 航空航天系列.抗拉强度不超过1249MPa的螺栓和空转螺母的一般要求规范 | Aerospace series - Specification for general requirements for bolts and free running nuts of tensile strength not exceeding 1249 MPa |
| BS 4A 102-2002 | 航空器用钢制螺栓(统一六角形和统一螺纹) | Specification for steel bolts (Unified hexagons and Unified threads) for aircraft |
| BS 4A 104-2002 | 飞行器用耐腐蚀钢螺栓(统一六角形和统一螺纹) | Specification for corrosion-resisting steel bolts (Unified hexagons and Unified threads) for aircraft |
| BS 4A 111-1993 | 具有紧公差杆的镀隔钢螺栓规范(统一六角形和统一螺纹) | Specification for cadmium-plated steel bolts (Unified hexagons and Unified threads) with close tolerance shanks |
| BS 4A 112-1992 | 镀隔钢抗剪螺栓规范(统一六角形和统一螺纹) | Specification for cadmium-plated steel shear bolts (Unified hexagons and Unified threads) |
| BS 4A 113-1999 | 镀镉蘑菇头统一螺纹开槽螺栓规范 | Specification for cadmium-plated, mushroom-headed, unified-thread, slotted drive, bolts |
| BS 4A 114-1999 | 耐腐蚀钢制蘑菇头开槽螺栓规范(强度等级880/1080) | Specification for corrosion-resisting steel, mushroom-headed, slotted-drive, bolts (strength class 880/1080) |
| BS 4A 169-2002 | 飞行器用铝合金螺栓(统一六角形和统一螺纹) | Specification for aluminium alloy bolts (Unified hexagons and Unified threads) for aircraft |
| BS 4A 170-1999 | 铝合金蘑菇头开槽螺栓(统一螺纹)规范 | Specification for aluminium alloy, mushroom-headed, slotted drive, bolts (unified thread) |
| BS 4A 228-1997 | 飞机用1250MPa(180,000lbf/in)钢双六角头螺栓规范 | Specification for steel double hexagon bolts - 1250 MPa (180,000 lbf/in2) for aircraft |
| BS 5125-1990 | 煤矿用50A 650V阻燃、保险和螺栓连接插头和插座规范 | Specification for 50 A 650 V flameproof, restrained and bolted plugs and sockets for use in coal mines |
| BS 5268-4.2-1990 | 建筑用木材.第4部分:木结构耐火性.第2节:木螺栓墙和格栅地板结构耐火性计算推荐标准 | Structural use of timber - Fire resistance of timber structures - Recommendations for calculating fire resistance of timber stud walls and joisted floor constructions |
| BS 5380-1984 | 用O 型圈密封及G 系列紧固螺纹的液压系流入口及连接螺栓规范 | Specification for hydraulic port and stud coupling using 'O'-ring sealing and 'G' series fastening threads |
| BS 5620-1995 | 矿山用1100V、200A安全防火与螺栓连接的插头与插座规范 | Specification for 200 A 1100 V flameproof restrained and bolted plugs and sockets for use in coal mines |
| BS 5655-8-1983 | 电梯与服务电梯.第8部分:电梯悬吊用有眼螺栓 | Lifts and service lifts - Part 8: Specification for eyebolts for lift suspension |
| BS 6040-1981 | 螺栓、螺钉、螺母和附件的名命 | Nomenclature for bolts, screws, nuts and accessories |
| BS 64-1992 | 铁路鱼尾板用的标准和高强度钢螺栓和螺母规范 | Specification for normal and high strength steel bolts and nuts for railway rail fishplates |
| BS 6487-1984 | 螺拴、螺钉和双头螺栓的开口销孔与保险孔规范 | Specification for split pin holes and wire holes in bolts, screws and studs |
| BS 6490-1984 | 运土机械的防松螺栓头外形和尺寸(不包括螺纹尺寸)规范 | Specification for shapes and dimensions (excluding thread dimensions) of plough bolt heads for earth-moving machinery |
| BS 7345-1990 | 螺栓、螺钉和螺柱标称长度和通用螺栓螺纹长度规范 | Specification for nominal lengths of bolts, screws and studs and thread lengths for general purpose bolts |
| BS 7419-1991 | 压紧螺栓规范 | Specification for holding down bolts |
| BS 7644-2-1993 | 直接拉力指示器.螺母面和螺栓面垫圈规范 | Direct tension indicators - Specification for nut face and bolt face washers |
| BS 7670-1-1993 | 电阻凸焊用钢螺母和螺栓.第1部分:尺寸和性能规范 | Steel nuts and bolts for resistance projection welding - Specification for dimensions and properties |
| BS 7670-2-1997 | 电阻凸焊的钢螺母和螺栓.焊接螺母和螺栓的焊接规范 | Steel nuts and bolts for resistance projection welding - Specification for welding of weld nuts and weld bolts |
| BS 7715-1994 | 具有非金属常用扭矩元件螺纹的流行式扭矩型螺栓、螺钉及螺柱规范 | Specification for prevailing torque type bolts, screws and studs with non-metallic prevailing torque elements incorporated into the thread |
| BS 7793-1-1995 | 螺栓固定钢板的瓷釉涂层.农业用泥浆罐的螺栓固定钢板的涂层规范 | Vitreous enamel coatings for use on bolted steel panels - Specification for coatings on bolted steel panels for use in agricultural slurry tanks |
| BS 7795-1995 | 预加微囊包封化学粘合件内装螺纹的螺栓、螺钉和螺柱规范 | Specification for bolts, screws and studs with a pre-applied micro-encapsulated chemical adhesive feature incorporated into the thread |
| BS 7814-1995 | 装有既可以头下锁紧又可以防止滚动功能的螺栓和螺钉规范 | Specification for bolts and screws incorporating either underhead locking or anti-rotation features |
| BS 7842-1996 | 具有预作用的螺纹密封特性的安装在螺纹上的螺栓、螺钉和螺柱 | Bolts, screws and studs with pre-applied thread sealing feature incorporated into the thread |
| BS 7861-2-1997 | 煤矿用地层支撑系统部件.鸟笼式电缆螺栓连接规范 | Strata reinforcement support system components used in coal mines - Specification for birdcaged cablebolting |
| BS 826-1978 | 钢制螺栓连接的单层搁板(立式角型) | Specification for steel single tier bolted shelving (angle upright type) |
| BS A 101-1969 | 钛螺栓一般要求规范 | Specification for general requirements for titanium bolts |
| BS A 226-1965 | 六角头钢螺栓规范(短螺纹:3A类) | Specification for steel hexagon head bolts (short thread: Class 3A) |
| BS A 227-1965 | 钢锅头螺栓规范(3A类短螺纹) | Specification for steel pan head bolts (short thread: Class 3A) |
| BS A 232-1968 | 100°埋头钢螺栓(160000磅力/平方英寸(110 hbar),规定扭矩槽)规范 | Specification for 100 ° countersunk head steel bolts (160 000 lbf/in2 (110 hbar) with Torq-set recesses) |
| BS A 254, A 255 [...]-1976 | 规范.六角头钛合金螺栓160 000 lbf/inUP2 (1100 MPa) | Specification - Hexagonal head titanium alloy bolts 160 000 lbf/inUP2 (1100 MPa) |
| BS A 254, A 255, A 256, A 257, A 258, A 259-1976 | 规范.六角头钛合金螺栓160 000 磅力/英寸(上标2)(1100MPa) | Specification - Hexagonal head titanium alloy bolts 160 000 lbf/inUP2 (1100 MPa) |
| BS A 254-1976 | 160,000磅力/平方英寸(1100MPa)六角头钛合金螺栓规范 | Specification - Hexagonal head titanium alloy bolts 160 000 lbf/in2 (1100 MPa) |
| BS A 266, A 267 [...]-1977 | 带高转距速度驱动凹槽的100 沉头钛合金螺栓160 000 lbf/inUP2 (1100 MPa)规范 | Specification for 100 ° countersunk head titanium alloy bolts 160 000 lbf/inUP2 (1100 MPa) with Hi-torque speed drive recesses |
| BS A 266, A 267, A 268, A 269, A 270, A 271-1977 | 有高转矩快速旋入凹槽的160000lbf/in<上标2>(1100MPa)的100°埋头钛合金螺栓规范 | Specification for 100 ° countersunk head titanium alloy bolts 160 000 lbf/inUP2 (1100 MPa) with Hi-torque speed drive recesses |
| BS A 266-1977 | 具有高扭矩速度引导槽的抗拉强度为160,000磅力/平方英寸(1100MPa)的100°沉头钛合金螺栓规范 | Specification for 100 ° countersunk head titanium alloy bolts 160 000 lbf/in2 (1100 MPa) with Hi-torque speed drive recesses |
| BS A 299-1989 | 抗拉强度为1250MPa和具有MJ螺纹的合金钢凸头螺栓采办规范 | Specification for procurement of alloy steel protruding head bolts with strength classification 1 250 MPa and MJ threads |
| BS A 300-1989 | 抗拉强度为1100MPa和具有MJ螺纹的合金钢螺栓采办规范 | Specification for procurement of alloy steel bolts with strength classification 1 100 MPa and MJ threads |
| BS A 301-1989 | 抗拉强度为1100MPa和具有MJ螺纹的耐热抗腐蚀螺栓采办规范 | Procurement of corrosion and heat-resisting steel bolts with strength classification 1100 MPa and MJ threads |
| BS A 303-1994 | 强度等级小于或等于1100 MPa的有涂层或无涂层短长度或中长度MJ螺纹的由金属材料制成的标称12角螺栓头标称杆 | Bolts, normal bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa - Dimensions |
| BS A 304-1994 | 强度等级小于或等于1100 MPa的有涂层或无涂层长长度MJ螺纹的由金属材料制成的标称12角螺栓头标称或节径杆螺 | Bolts, normal bihexagonal head, normal or pitch diameter shank, long length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa - Dimensions |
| BS A 305-1994 | 螺栓. 试验方法 | Bolts - Test methods |
| BS A 307-1994 | 强度等级小于或等于1100 MPa的有涂层或无涂层长长度MJ螺纹由金属材料制成的标称花键头、标称或节径杆螺栓. | Bolts, normal spline head, normal or pitch diameter shank, long length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa - Dimensions |
| BS A 308-1994 | 强度等级小于或等于1100 MPa的有涂层或无涂层短长度或中长度MJ螺纹的由金属材料制成的标称花键头标称杆螺栓 | Bolts, normal spline head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa - Dimensions |
| BS A 309-1994 | 强度等级小于或等于1100 MPa的有涂层或无涂层长长度MJ螺纹的由金属材料制成的大六角头标称或节径杆螺栓.尺 | Bolts, large hexagonal head, normal or pitch diameter shank, long length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa - Dimensions |
| BS A 310-1995 | 强度等级小于或等于1250MPa-1800MPa的有涂层或无涂层短长度或中长度MJ螺纹的由金属材料制成的标称大12角螺 | Bolts, large bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes 1250 MPa to 1800 MPa - Dimensions |
| BS A 332-1999 | 航空航天用1100MPa强度的MJ螺纹钛合金螺栓.采购规范 | Aerospace - Bolts, with MJ threads, in titanium alloys, strength class 1 100 MPa - Procurement specification |
| BS A 358-2-2000 | MJ螺纹.螺栓和螺母的极限尺寸 | MJ threads - Limit dimensions for bolts and nuts |
| BS A 363-2000 | 强度等级为1550MPa耐热镍基合金MJ螺纹螺栓.采购规范 | Bolts, with MJ threads, made of heat-resistant nickel-based alloy, strength class 1 550 MPa - Procurement specification |
| BS AU 190-1983 | 拖载达2000kg的挂车三角形拉杆上超限装置安装面尺寸和固定螺栓规范 | Specification for interface dimensions and fixing bolts for the mounting of overrun devices on delta shaped drawbars of trailers up to 2000 kg |
| BS AU 50-2.3-1994 | 轮胎和车轮.第2部分:车轮和轮辋.第3节:商用车辆的道路车轮螺母、双头螺栓和螺栓规范 | Tyres and wheels - Wheels and rims - Specification for road-wheel nuts, studs and bolts for commercial vehicles |
| BS DD CEN/TS 1591-4-2007 | 法兰及其连接件.带垫圈圆形法兰连接件的设计原则.符合压力设备指令的螺栓连接件装配职工能力的合格鉴定 | Flanges and their joints - Design rules for gasketed circular flange connections - Qualification of personnel competency in the assembly of bolted joints fitted to equipment subject to the Pressure Equipment Directive |
| BS EN 10319-2-2006 | 金属材料.拉伸应力松弛测试.螺栓连接模型用程序 | Metallic materials - Tensile stress relaxation testing - Procedure for bolted joint models |
| BS EN 13411-5-2003 | 钢丝绳接线端.安全.U形螺栓钢丝绳夹具 | Terminations for steel wire ropes - Safety - U-bolt wire rope grips |
| BS EN 14219-2003 | 米制细牙螺纹六角法兰面螺栓.小系列 | Hexagon bolts with flange with metric fine pitch thread - Small series |
| BS EN 14399-1-2005 | 预加负荷用高强度结构螺栓组件.一般要求 | High-strength structural bolting assemblies for preloading - General requirements |
| BS EN 14399-2-2005 | 预加负荷用高强度结构螺栓组件.预加负荷的适合性试验 | High-strength structural bolting assemblies for preloading - Suitability test for preloading |
| BS EN 14399-3-2005 | 预加负荷用高强度结构螺栓组件.系统HR.六角螺栓和螺母组件 | High-strength structural bolting for preloading - System HR - Hexagon bolt and nut assemblies |
| BS EN 14399-4-2005 | 预负载用高强度结构螺栓连接组件.系统HV.六螺栓和螺母组件 | High-strength structural bolting assemblies for preloading - System HV - Hexagon bolt and nut assemblies |
| BS EN 14399-5-2005 | 预负载用高强度结构螺栓连接组件.平垫圈 | High-strength structural bolting assemblies for preloading - Plain washers |
| BS EN 14399-6-2005 | 预负载用高强度结构螺栓连接组件.平倒角垫圈 | High-strength structural bolting assemblies for preloading - Plain chamfered washers |
| BS EN 15048-1-2007 | 非预加负荷结构的螺栓连接组件.一般要求 | Non-preloaded structural bolting assemblies - General requirements |
| BS EN 15048-2-2007 | 非预加负荷结构的螺栓连接组件.适宜性试验 | Non-preloaded structural bolting assemblies - Suitability test |
| BS EN 1515-1-2000 | 法兰及其接头.螺栓连接.螺栓连接的选择 | Flanges and their joints - Bolting - Selection of bolting |
| BS EN 1515-2-2002 | 法兰及其连接件.螺栓连接. PN 标识的钢法兰用的螺栓材料分类 | Flanges and their joints - Bolting - Classification of bolt materials for steel flanges, PN designated |
| BS EN 1515-3-2005 | 法兰及其连接件.螺栓连接.等级标注的钢法兰用螺栓材料的分类 | Flanges and their joints - Bolting - Classification of bolt materials for steel flanges, class designated |
| BS EN 15282-2007 | 釉层和搪瓷.储水、处理水、市政或工业排水和污水用螺栓连接钢罐的设计 | Vitreous and porcelain enamels - Design of bolted steel tanks for the storage or treatment of water or municipal or industrial effluents and sludges |
| BS EN 1662-1998 | 带法兰的六角螺栓.小型系列 | Hexagon bolts with flange - Small series |
| BS EN 1665-1997 | 带法兰缘的六角头螺栓.重型系列 | Hexagon bolts with flange - Heavy series |
| BS EN 20225-1992 | 紧固件.螺栓、螺柱和螺母.图形符号和尺寸 | Fasteners - Bolts, screws, studs and nuts - Symbols and designations of dimensions |
| BS EN 20273-1992 | 紧固件.螺栓和螺钉自由尺寸孔 | Fasteners - Clearance holes for bolts and screws |
| BS EN 20898-7-1995 | 紧固件机械性能.标称直径为1MM到10MM的螺栓和螺钉的扭转试验和最小扭矩 | Mechanical properties of fasteners - Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm |
| BS EN 24015-1992 | 六角头螺栓.B级产品.减缩杆(杆径近似中径) | Hexagon head bolts - Product grade B. Reduced shank (shank diameter pitch diameter) |
| BS EN 2413-1995 | 镀镉的合金钢短螺纹紧公差薄六角头带肩螺栓.等级:1100MPa(室温)/235℃ | Bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in alloy steel, cadmium plated - Classification: 1100 MPa (at ambient temperature)/235 °C |
| BS EN 2549-2006 | 航空航天系列.二硫化钼润滑阳极处理的钛制短螺纹紧公差标准螺杆标准六角头螺栓.等级:1100MPa(室温)/315℃ | Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature) / 315 °C |
| BS EN 2583-1997 | 耐热镍基合金NI-PH2601(铬镍铁合金718)MJ螺纹螺栓.等级:1275MPa(室温)/650℃.技术规范 | Bolts, MJ threads, in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification: 1275 MPa (at ambient temperature)/650 °C - Technical specification |
| BS EN 26157-1-1992 | 紧固件的表面不均匀性.第1部分:一般要求的螺栓、螺钉和螺柱 | Fasteners - Surface discontinuities - Bolts, screws and studs for general requirements |
| BS EN 26157-3-1992 | 紧固件的表面不均匀性.第3部分:有特殊要求的螺栓、螺钉和螺柱 | Fasteners - Surface discontinuities - Bolts, screws and studs for special requirements |
| BS EN 2859-2006 | 航空航天系列.镀镉合金钢短螺纹紧公差标准螺杆标准六角头螺栓.等级:1100MPa(室温)/235℃ | Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in alloy steel, cadmium plated - Classification: 1100 MPa (at ambient temperature) / 235 °C |
| BS EN 2870-1996 | 二硫化钼润滑的阳极化的钛合金短螺纹紧公差标准螺杆标准双六角头螺栓.等级:1100MPa(室温)/315℃ | Bolts, normal bihexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature) /315 °C |
| BS EN 2874-1996 | 钝化处理的耐热镍基合金中长度螺纹紧公差标准螺杆的大双六角头螺栓.等级:1550MPa(室温)/315℃ | Bolts, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated - Classification: 1550 MPa (at ambient temperature) /315 °C |
| BS EN 28839-1992 | 紧固件机械性能.有色金属制螺栓、螺钉、螺柱和螺母 | Mechanical properties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals |
| BS EN 2887-1995 | 钝化处理的耐蚀钢的螺纹至螺栓头的标准六角头螺栓.等级:600MPa(室温)/425℃ | Bolts, normal hexagonal head, threaded to head, in corrosion resisting steel, passivated - Classification: 600 MPa (at ambient temperature)/425 °C |
| BS EN 2888-2006 | 钝化耐蚀钢制短螺纹粗公差标准螺杆标准六角头米制螺栓.分类:600MPa(室温)/425℃ | Aerospace series - Metric bolts, normal hexagon head, coarse tolerance normal shank, short thread, in corrosion resisting steel, passivated - Classification: 600 MPa (at ambient temperature) / 425 °C |
| BS EN 2925-1994 | FE-PA92HT(A286)耐热钢制长螺纹减荷螺杆的双六角头螺栓.等级:900MPa(室温)/650℃ | Bolts, double hexagon head, relieved shank, long thread, in heat resisting steel FE-PA92HT (A 286) - Classification: 900 MPa (at ambient temperature)/650 °C |
| BS EN 2926-1996 | 镀银的FE-FA92HT(A286)耐热钢长螺纹减荷螺杆的双六角头螺栓.等级:900MPa(室温)/650℃ | Bolts, double hexagon head, relieved shank, long thread, in heat resisting steel FE-PA92HT (A286), silver plated - Classification: 900 MPa (at ambient temperature)/650 °C |
| BS EN 2927-1996 | NI-P100HT(铬镍铁合金 718)耐热镍基合金长螺纹减荷螺杆双六角头螺栓.等级:1275MPa(室温)/650℃ | Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718) - Classification:1275 MPa (at ambient temperature)/650 °C |
| BS EN 2928-1996 | 镀银的NI-P100HT(铬镍铁合金 718)耐热镍基合金长螺纹减荷螺杆的双六角头螺栓.等级:1275MPa(室温)/650℃ | Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718), silver plated - Classification: 1275 MPa (at ambient temperature)/650 °C |
| BS EN 2929-1996 | NI-P101HT(Waspaloy)型耐热镍基合金制长螺纹安全柄十二角头螺栓.等级:1210MPa(室温)/730℃ | Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy) - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 2930-1996 | 镀银的NI-P101HT(沃斯帕洛尹)耐热镍基合金长螺纹减荷螺杆的双六角头螺栓.等级:1210MPa(室温)/730℃ | Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy), silver plated - Classification:1210 MPa (at ambient temperature)/730 °C |
| BS EN 2931-1994 | FE-PA92HT(A286)耐热钢制的长螺纹减荷螺杆的T型头螺栓.等级:900MPa(室温)/650℃ | Bolts, T-head, relieved shank, long thread, in heat resisting steel FE-PA92HT (A286) - Classification: 900 MPa (at ambient temperature)/650 °C |
| BS EN 2932-1996 | 镀银FE-PA92HT(A286)耐热钢制长螺纹安全柄T型头螺栓.等级:900MPa(室温)/650℃ | Bolts, T-head, relieved shank, long thread, in heat resisting steel FE-PA92HT (A286), silver plated - Classification: 900 MPa (at ambient temperature)/650 °C |
| BS EN 2933-1996 | NI-P100HT(铬镍铁合金 718)耐热镍基合金长螺纹减荷螺杆的T型头螺栓.等级:1275MPa(室温)/650℃ | Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718) - Classification:1275 MPa (at ambient temperature)/650 °C |
| BS EN 2934-1996 | 镀银的NI-P100HT(铬镍铁合金 718)耐热镍基合金长螺纹减荷螺杆的T型头螺栓.等级:1275MPa(室温)/650℃ | Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718), silver plated - Classification:1275 MPa (at ambient temperature)/650 °C |
| BS EN 2935-1996 | NI-P101HT(沃斯帕洛尹)耐热镍基合金长螺纹减荷螺杆的T型头螺栓.等级:1210MPa(室温)/730℃ | Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy) - Classification:1210 MPa (at ambient temperature)/730 °C |
| BS EN 2936-1996 | 镀银的NI-P101HT(沃斯帕洛尹)耐热镍基合金长螺纹减荷螺杆的T型头螺栓.等级:1210MPa(室温)/730℃ | Bolts, T-head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy), silver plated - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 3006-1994 | FE-PA92HT(A286)耐热钢长螺纹减荷螺杆的六角头螺栓.等级:900 MPa(室温)/650℃ | Bolts, hexagon head, relieved shank, long thread, in heat resisting steel FE-PA92HT (A286) - Classification: 900 MPa (at ambient temperature)/650 °C |
| BS EN 3007-1996 | 镀银的FE-PA92HT(A286)耐热钢长螺纹减荷螺杆的六角头螺栓.等级:900 MPa(室温)/650℃ | Bolts, hexagon head, relieved shank, long thread, in heat resisting steel FE-PA92HT (A286), Silver plated - Classification: 900 MPa (at ambient temperature)/650 °C |
| BS EN 3008-1998 | 耐热镍基合金NI-P100HT(铬镍铁合金718)制薄柄长螺纹六角头螺栓.等级:1275 MPa(室温)/650℃ | Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718) - Classification:1275 MPa (at ambient temperature)/650 °C |
| BS EN 3009-1998 | 镀银耐热镍基合金NI-P100HT(铬镍铁合金718)制薄柄长螺纹六角头螺栓.等级:1275 MPa(室温)/650℃ | Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P100HT (Inconel 718), silver plated - Classification - 1275 MPa (at ambient temperature)/650 °C |
| BS EN 3010-1998 | 耐热镍基合金NI-P101HT(沃斯帕洛尹合金)薄柄长螺纹六角头螺栓.等级:1210 MPa(室温)/730℃ | Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy) - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 3011-1998 | 镀银耐热镍基合金NI-P101HT(沃斯帕洛尹合金)薄柄长螺纹六角头螺栓.等级:1210 MPa(室温)/730℃ | Bolts, hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy), silver plated - Classification:1210 MPa (at ambient temperature)/730 °C |
| BS EN 3052-1994 | 钝化处理的耐热耐蚀钢制短螺纹紧公差标准螺杆标准六角头螺栓.等级:1100 MPa(室温)/425℃ | Bolts, normal hexagonal head, close tolerance normal shank, short thread, in heat and corrosion resisting steel, passivated - Classification: 1100 MPa (at ambient temperature)/425 °C |
| BS EN 3063-1994 | 耐热镍基合金NI-P101HT(沃斯帕洛尹合金)制的中长度螺纹紧公差螺杆双六角头螺栓.等级:1210 MPa(室温)/730℃ | Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy) - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 3112-1995 | 镀镉的合金钢的螺纹至螺栓头的标准六角头螺栓.等级:900 MPa(室温)/235℃ | Bolts, normal hexagonal head, threaded to head, in alloy steel, cadmium plated - Classification: 900 MPa (at ambient temperature)/235 °C |
| BS EN 3379-1996 | 镀银的NI-P101HT(沃斯帕洛尹)耐热镍基合金中长度螺纹紧公差螺杆的双六角头螺栓.等级:1210 MPa(室温)/730℃ | Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-P101HT (Waspaloy), for increased height nuts - Classification: 1210 MPa (at ambient temperature)/730 °C |
| BS EN 3444-2006 | 航空航天系列.钝化镍合金制耐热、标准柄、紧公差中长螺纹大直径十二沉头螺栓.等级:1250MPa(室温)/650℃ | Aerospace series - Bolt, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated - Classification: 1250 MPa (at ambient temperature) / 650 ℃ |
| BS EN 3724-2004 | 细杆长螺纹双六角头镀MoS2的钛合金TI-P64001螺栓.强度等级:1100MPa(室温) | Bolts, double hexagon head, relieved shank, long thread, in titanium alloy TI-P64001, MoS2 coated - Strength class: 1100 MPa (at ambient temperature) |
| BS EN 3740-1997 | 二硫化钼润滑的阳极化的钛合金短螺纹紧公差螺杆薄六角头带肩螺栓.等级:1100 MPa(室温)/315℃ | Bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3818-2005 | 航空航天系列.MJ螺纹的钛合金TI-P64001螺栓.强度等级:1100MPa(室温).技术规范 | Aerospace series - Bolts, MJ threads, in titanium alloy TI-P64001 - Strength class: 1100 MPa (at ambient temperature) - Technical specification |
| BS EN 3832-2005 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金718)制长螺纹、细杆、十二角螺栓.等级:1550MPa(室温)/650℃ | Aerospace series - Bolts, double hexagon head, relieved shank, long thread, in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification: 1550 MPa (at ambient temperature) / 650 °C |
| BS EN 3833-2005 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金718)制MJ螺纹螺栓.等级:1550MPa(室温)/650℃.技术规范 | Aerospace series - Bolts, MJ threads, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), passivated - Classification: 1550 MPa (at ambient temperature) / 650 °C - Technical specification |
| BS EN 3907-2004 | 航空航天系列.标准杆长螺纹双六角头镀MoS2的钛合金TI-P64001螺栓.等级:1100MPa(室温)/350 鳦 | Aerospace series - Bolts, double hexagon head, normal shank, long thread, in titanium alloy TI-P64001, MoS2 coated - Classification: 1100MPa (at ambient temperature)/350 °C |
| BS EN 3912-2007 | 航空航天系列.镀银FE-PA2601(FE-PA92HT,A286)型长螺纹细杆六瓣凹槽平头螺栓耐热钢.分类:1100MPa(环境温度)/ | Aerospace series - Bolts, pan head, six lobe recess, relieved shank, long thread, in heat resisting steel FE-PA2601 (FE-PA92HT, A286), silver plated - Classification: 1100 MPa (at ambient temperature) / 650 °C |
| BS EN 4009-2005 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金718)制中长螺纹、紧公差柄、十二角头螺栓.等级:1550MPa(室 | Aerospace series - Bolts, double hexagon head, close tolerance shank, medium length thread, in heat resisting nickel base alloy NI-PH2601 (Inconel 718) - Classification: 1550 MPa (at ambient temperature) |
| BS EN 4172-2006 | 航空航天系列.紧公差TI-P64001阳极电镀的米制钛合金杆沉头、凹头锁紧螺栓.分类:1100 MPa / 315 °C（周围温 | Lockbolts, protruding head, sheartype, close tolerance, in titanium alloy TI-P64001, anodized, metric series - Classification: 1 100 MPa (at ambient temperature) / 315 °C |
| BS EN 4173-2006 | 航空航天系列.紧公差TI-P64001阳极电镀的米制钛合金杆１００°正常头、凹头锁紧螺栓.分类:1100 MPa / 315 | Lockbolts, 100 countersunk normal head, sheartype, close tolerance, in titanium alloy TI-P64001, anodized, metric series - Classification: 1100 MPa (at ambient temperature) / 315 °C |
| BS EN 4176-2005 | 航空航天系列.紧公差TI-P64001钛合金制阳极电镀或铝质有色覆层１００°正常或沉头紧固/凹头锁紧螺栓.TI-P99 | Aerospace series - Lockbolts, 100 ° countersunk normal head or protruding head, tension-/ sheartype, close tolerance, in titanium alloy TI-P64001, anodized or with aluminium pigmented coating - Collars in titanium TI-P99002 or aluminium alloy 2024 - Metric series - Technical specification |
| BS EN 4321-2004 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金 718)制的带安全锁线孔、细杆、长螺纹、镀银的双六角头螺栓 | Aerospace series - Bolts, double hexagon head with lockwire holes , relieved shank, long thread, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), silver plated - Classification - 1 550 Mpa (at ambient temperature)/650 °C |
| BS EN 4322-2004 | 航空航天系列.钛合金TI-P64001制的带安全锁线孔、细杆、长螺纹、阳极氧化、镀MoS2的双六角头螺栓.强度等级. | Aerospace series - Bolts, double hexagon head with lockwire holes , relieved shank, long thread, in titanium alloy TI-P64001, anodized , MoS2 coated - Strength class - 1 100 MPa (at ambient temperature) |
| BS EN 4352-2004 | 航空航天系列.耐热镍基合金NI-PH2601(铬镍铁合金 718)制带安全锁线孔、细杆、长螺纹、镀MoS2 的双六角头螺 | Aerospace series - Bolts, double hexagon head with lockwire holes , relieved shank, long thread, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), MoS2 coated - Classification - 1 550 MPa (at ambient temperature) / 425 °C |
| BS EN 4401-2006 | 航空航天系列.紧公差TI-P64001铝制有色覆层的米制钛合金杆沉头、凹头锁紧螺栓.分类:1100 MPa / 315 °C（周 | Lockbolts, protruding head, sheartype, close tolerance, in titanium alloy TI-P64001, with aluminium pigmented coating, metric series - Classification: 1100 MPa (at ambient temperature) / 315 °C |
| BS EN 4402-2006 | 航空航天系列.紧公差TI-P64001铝制有色覆层的米制钛合金杆１００°正常头、凹头锁紧螺栓.分类:1100 MPa / 3 | Lockbolts, 100 °countersunk normal head, sheartype, close tolerance, in titanium alloy TI-P64001,with aluminium pigmented coating, metric series - Classification: 1100 MPa (at ambient temperature) / 315 °C |
| BS EN 4498-2005 | 航空航天系列.有色铝涂层、钝化的、耐热镍基合金、中等长度螺纹、紧公差标称杆、大双六角头螺栓.等级:1550M | Aerospace series - Bolts, large bihexagonal head, close tolerance normal shank, medium length thread, in heat resisting nickel base alloy, passivated, with aluminium pigmented coating - Classification: 1 550 MPa (at ambient temperature) / 315 °C |
| BS EN 4501-2006 | 航空航天系列.带镀铝涂层的阳极电镀钛合金短螺纹紧公差标准柄正六角头螺栓、米制系列.等级:1100MPa(室温)/3 | Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating, metric series - Classification: 1100 MPa (at ambient temperature) / 315 °C |
| BS EN ISO 10434-2004 | 石油、石化和相关工业用螺栓帽状钢闸阀 | Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries |
| BS EN ISO 10664-2005 | 螺栓和螺钉用内板拧的六角花形 | Hexalobular internal driving feature for bolts and screws |
| BS EN ISO 13918-1998 | 焊接.弧螺栓焊用螺栓和陶瓷箍套 | Welding - Studs and ceramic ferrules for arc stud welding |
| BS EN ISO 14555-2006 | 焊接.金属材料的电弧螺栓焊 | Welding - Arc stud welding of metallic materials |
| BS EN ISO 3506-1-1998 | 耐腐蚀不锈钢紧固件的机械特性.螺栓、螺钉和螺柱 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Bolts, screws and studs |
| BS EN ISO 4014-2001 | 六角头螺栓.产品等级A和B级 | Hexagon head bolts - Product grades A and B |
| BS EN ISO 4016-2001 | 六角头螺栓.产品等级C级 | Hexagon head bolts - Product grade C |
| BS EN ISO 4759-1-2001 | 紧固件公差.螺栓、螺钉、螺柱和螺母.产品等级A、B和C级 | Tolerances for fasteners - Bolts, screws, studs and nuts - Product grades A, B and C |
| BS EN ISO 4759-3-2000 | 紧固件公差.螺栓、螺钉和螺母用平垫圈.产品等级A和C | Tolerances for fasteners - Plain washers for bolts, screws and nuts - Product grades A and C |
| BS EN ISO 8765-2001 | 米制细牙螺纹六角头螺栓.产品等级A和B级 | Hexagon head bolts with metric fine pitch thread - Product grades A and B |
| BS EN ISO 887-2000 | 通用米制螺栓、螺钉和螺母用平垫圈.总方案 | Plain washers for metric bolts, screws and nuts for general purposes - General plan |
| BS EN ISO 898-1-1999 | 碳钢和合金钢制的紧固件的机械特性.螺栓、螺钉和螺柱 | Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws and studs |
| BS EN ISO 9974-1-2000 | 普通和液压传动用联接件.用ISO 261弹性螺纹或金属与金属间密封的气门和双头螺栓端头.螺纹气门 | Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Threaded ports |
| BS EN ISO 9974-2-2000 | 普通和液压传动用联接件.用ISO 261弹性螺纹或金属与金属间密封的气门和双头螺栓端头.(E型)弹性密封的双头螺 | Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Stud ends with elastomeric sealing (type E) |
| BS EN ISO 9974-3-2000 | 普通和液压用联接结件.用ISO 261螺纹的弹性或金属与金属间密封的气门和双头螺栓端头.(B型)金属与金属间密封 | Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Stud ends with metal-to-metal sealing (type B) |
| BS HR 650-1972 | 制造螺栓、螺柱、定位螺钉和螺母用耐热高膨胀钢棒材和线材(Ni25.5、Cr15、Ti2、Mn1.5、Mo1.25、Si0.7、V0.3 | Specification for high expansion heat-resisting steel bar and wire for the manufacture of bolts, studs, set screws and nuts (Ni 25.5, Cr 15, Ti 2, Mn 1.5, Mo 1.25, Si 0.7, V 0.3) (limiting ruling section 20 mm) |
| BS ISO 15072-2000 | 公制细牙螺纹法兰盘六角螺栓.小型系列.A级产品 | Hexagon bolts with flange with metric fine pitch thread - Small series - Product grade A |
| BS ISO 262-1999 | ISO普通米制螺纹.螺钉,螺栓和螺母的选用尺寸 | ISO general purpose metric screw threads - Selected sizes for screws, bolts and nuts |
| BS ISO 5894-2000 | 船舶与海上技术.用螺栓紧固盖子的人孔 | Ships and marine technology - Manholes with bolted covers |
| BS ISO 8820-6-2007 | 道路车辆.熔断体.单螺栓熔断体 | Road vehicles - Fuse-links - Single-bolt fuse-links |
| BS ISO 885-2000 | 一般用途螺栓和螺钉.米制系列.头下圆角半径 | General purpose bolts and screws - Metric series - Radii under the head |
| BS ISO 8992-2005 | 紧固件.螺栓、螺钉、螺柱和螺母通用要求 | Fasteners - General requirements for bolts, screws, studs and nuts |
| BS M 85-1995 | 空运货物设备.全向额定载荷容量为2225N(5000 1bf)或以上的双头螺栓系紧配件标识 | Air cargo equipment - Identification of double-stud tie-down fittings having an omnidirectional rated load capacity of 22 250 N (5 000 lbf) or above |
| BS S 148-1969 | 仅用于锻制螺栓的低镍-铬钢棒规范 | Specification for low nickel-chromium steel (bar for the manufacture of forged bolts only) |
| BS S 158-1977 | 锻制螺栓和螺母的含1%铬-钼钢棒规范 | Specification for 1% chromium-molybdenum steel bars for the manufacture of forged bolts and forged nuts |
| BS SP 114-1955 | 航空用有眼螺栓(统一螺纹)规范 | Specification for eye bolts (Unified threads) for aircraft |
| 编号 | 中文名称 | 英文名称 |