| 编号 | 中文名称 | 英文名称 |
|---|
| BS 2G 124-1-1966
| 飞机交流发电机规范.恒定频率
| Specification for a.c. generators for aircraft - Constant frequency
|
| BS 2G 147-2-1966
| 飞机交流电动机规范.第2部分:三相可变频率鼠笼式感应电动机
| Specification for a.c. motors for aircraft - Three-phase variable frequency squirrel-cage induction motors
|
| BS 3816-1989
| 电源频率的电气绝缘用环氧树脂浇铸系统规范
| Specification for epoxy resin casting systems used for electrical insulating applications at power frequencies
|
| BS 5271-1988
| 工业用低压开关和控制装置规范.近距离电感开关.工作距离和工作频率测量方法
| Specification for low-voltage switchgear and controlgear for industrial use - Inductive proximity switches - Methods for measuring the operating distance and operating frequency
|
| BS 5640-1-1978
| 频率范围为30MHz-1GHz的电台与电视广播接收天线.第1部分:机械电气特性规范
| Aerials for the reception of sound and television broadcasting in the frequency range 30 MHz to 1 GHz - Specification for electrical and mechanical characteristics
|
| BS 5640-2-1978
| 频率范围为30MHz-1GHz的电台与电视广播接收天线.第2部分:电气性能参数测量方法
| Aerials for the reception of sound and television broadcasting in the frequency range 30 MHz to 1 GHz - Methods of measurement of electrical performance parameters
|
| BS 5721-1979
| 飞机噪声测量用频率加权(D加权)规范
| Specification for frequency weighting for the measurement of aircraft noise (D-weighting)
|
| BS 6397-1983
| 绘制频率特性和极坐标图用标度和尺寸规范
| Specification for scales and sizes for plotting frequency characteristics and polar diagrams
|
| BS 6472-1992
| 建筑物振动(频率为1-80Hz)对人影响的评定指南
| Guide to evaluation of human exposure to vibration in buildings (1 Hz to 80 Hz)
|
| BS 6955-14-1994
| 振动和冲击传感器的校准.钢铸锭无阻尼加速度计共振频率的试验方法
| Calibration of vibration and shock pick-ups - Method of test for resonance frequency of undamped accelerometers on a steel block
|
| BS 6958-1-1988
| 采用改进的频率调制在每面80磁道上以7958磁通变换/弧度(ftprad)、5.3tpmm(135tpi)记录的数据交换用90mm(3.5
| Guide to construction and use of 90 mm (3.5 in) flexible disk cartridges for data interchange, using modified frequency modulation recording at 7958 ftprad, 5.3 tpmm (135 tpi) on 80 tracks on each side - Dimensional, physical and magnetic characteristics
|
| BS 6958-2-1988
| 采用改进的频率调制在每面80磁道上以7958磁通变换/弧度(ftprad)、5.3tpmm(135tpi)记录的数据交换用90mm(3.5
| Guide to construction and use of 90 mm (3.5 in) flexible disk cartridges for data interchange, using modified frequency modulation recording at 7958 ftprad, 5.3 tpmm (135 tpi) on 80 tracks on each side - Track format
|
| BS 7023-1-1989
| 使用改进的频率调制以7958ftprad、3.8tpmm(96tpi)速度双面录制的数据交换用130mm(5.25in)软磁盘盒的制造和
| Guide to construction and use of 130 mm (5.25 in) flexible disk cartridges for data interchange using modified frequency modulation recording at 7958 ftprad, 3.8 tpmm (96 tpi) on both sides - Dimensional, physical and magnetic characteristics
|
| BS 7023-2-1989
| 使用改进的频率调制以7958ftprad、3.8tpmm(96tpi)速度双面录制的数据交换用130mm(5.25in)软磁盘盒的制造和
| Guide to construction and use of 130 mm (5.25 in) flexible disk cartridges for data interchange using modified frequency modulation recording at 7958 ftprad, 3.8 tpmm (96 tpi) on both sides - Track format A
|
| BS 7023-3-1989
| 使用改进的频率调制以7958ftprad、3.8tpmm(96tpi)速度双面录制的数据交换用130mm(5.25in)软磁盘盒的制造和
| Guide to construction and use of 130 mm (5.25 in) flexible disk cartridges for data interchange using modified frequency modulation recording at 7958 ftprad, 3.8 tpmm (96 tpi) on both sides - Track format B
|
| BS 7024-2-1989
| 使用改进的频率调制以7958ftprad、1.9tpmm(48tpi)速度双面录制的数据交换用130mm(5.25in)软磁盘盒的制造和
| Guide to construction and use of 130 mm (5.25 in) flexible disk cartridges for data interchange using modified frequency modulation recording at 7958 ftprad, 1.9 tpmm (48 tpi) on both sides - Track format A
|
| BS 7024-3-1989
| 使用改进的频率调制以7958ftprad、1.9tpmm(48tpi)速度双面录制的数据交换用130mm(5.25in)软磁盘盒的制造和
| Guide to construction and use of 130 mm (5.25 in) flexible disk cartridges for data interchange using modified frequency modulation recording at 7958 ftprad, 1.9 tpmm (48 tpi) on both sides - Track format B
|
| BS 7041-1989
| 频率范围为0.5MHz到15MHz的水珍器操作特性和校准规范
| Specification for characteristics and calibration of hydrophones for operation in the frequency range 0.5 MHz to 15 MHz
|
| BS 7737-1-1995
| 频率大于300MHz的绝缘材料介电性能测定用推荐方法
| Recommended methods for the determination of the dielectric properties of insulating materials at frequencies above 300 MHz - General
|
| BS 7737-2-1995
| 频率大于300MHz介质性能测定的推荐方法.谐振法
| Recommended methods for the determination of the dielectric properties of insulating materials at frequencies above 300 MHz - Resonance methods
|
| BS 89-4-1990
| 直接指示模拟电工测量仪表及其附件.频率表的特殊要求规范
| Direct acting indicating analogue electrical measuring instruments and their accessories - Specification for special requirements for frequency meters
|
| BS 9031-1971
| 经质量评定的固定频率脉冲磁控管详细规范编制规则
| Rules for the preparation of detail specifications for pulsed fixed-frequency magnetrons of assessed quality
|
| BS 9032-1975
| 经质量评估的脉冲磁控管(不包括频率捷变磁控管)详细规范的制定规则.基本评估级
| Rules for the preparation of detail specifications for pulsed magnetrons (excluding frequency-agile magnetrons) of assessed quality - Basic assessment level
|
| BS 9612 N004-1977
| 振荡器用冷焊密封石英晶体振子详细规范.DN、47 U/2、DQ和DP外壳、0.8至20MHz和3.0到30MHz频率范围.宽温范围
| Detail specification for cold welded seal quartz crystal units for oscillator applications - DN, 47 U/2, DQ and DP enclosures, 0.8 to 20 MHz and 3.0 to 30 MHz frequency ranges - Fundamental thickness-shear mode, AT-cut, for operation over wide temperature ranges (non-temperature controlled) - Full assessment level
|
| BS 9612 N005-1977
| 振荡器用冷焊密封石英晶体振子详细规范.DN、DQ和DP外壳、0.8至20MHz和3.0到30MHz频率范围.窄温范围(非温控)
| Detail specification for cold welded seal quartz crystal units for oscillator applications - DN, DQ and DP enclosures, 0.8 to 20 MHz and 3.0 to 30 MHz frequency ranges - Fundamental thickness-shear mode , AT-cut, for operation over narrow temperature ranges (temperature controlled) - Full assessment level
|
| BS 9612 N006-1977
| 振荡器用冷焊密封石英晶体振子详细规范.DN、47U/2、DQ和DP外壳、17至75MHz频率范围.宽温范围(非温控)操作的
| Detail specification for cold welded seal quartz crystal units for oscillator applications - DN, 47 U/2, DQ and DP enclosures, 17 to 75 MHz frequency range - Third overtone thickness-shear mode, AT-cut, for operation over wide temperature ranges (non-temperature controlled) - Full assessment level
|
| BS 9612 N007-1977
| 振荡器用冷焊密封石英晶体振子详细规范.DN、DQ和DP外壳、17至75MHz频率范围.窄温范围(非温控)操作用第三谐
| Detail specification for cold welded seal quartz crystal units for oscillator applications - DN, DQ and DP enclosures, 17 to 75 MHz frequency range - Third overtone thickness-shear mode, AT-cut, for operation over narrow temperature ranges (temperature controlled) - Full assessment level
|
| BS 9612 N008-1977
| 振荡器用冷焊密封石英晶体振子详细规范.DN、DQ和DP外壳、50至125MHz频率规范.宽温范围(非温控)操作用第五谐
| Detail specification for cold welded seal quartz crystal units for oscillator applications - DN, DQ and DP enclosures, 50 to 125 MHz frequency range - Fifth overtone thickness-shear mode, AT-cut, for operation over wide temperature ranges (non-temperature controlled) - Full assessment level
|
| BS 9612 N009-1977
| 经质量评定的振荡器用冷焊封石英晶体振子详细规范.DN、DQ和DP外壳,50至125MHz频率规范.窄温范围(非温控)操
| Detail specification for cold welded seal quartz crystal units for oscillator applications - DN, DQ and DP enclosures, 50 to 125 MHz frequency range - Fifth overtone thickness-shear mode, AT-cut, for operation over narrow temperature ranges (temperature controlled) - Full assessment level
|
| BS 9612 N010-1979
| 振荡器用冷焊密封石英晶体振子详细规范.DP外壳、6.0至25MHz频率范围.宽温范围(非温控)操作的基波厚度剪切模
| Detail specification for cold welded seal quartz crystal units for oscillator applications - DK enclosure, 6.0 to 25 MHz frequency range - Fundamental thickness-shear mode, AT-cut, for operation over wide temperature ranges (non-temperature controlled) - Full assessment level
|
| BS 9612 N016-1979
| 振荡器用冷焊密封石英晶体振子详细规范.DN、D2、DQ和DP外壳、0.8至20MHz和3.0到30MHz频率范围.宽温范围(非
| Detail specification for resistance welded seal quartz crystal units for oscillator applications - DN, DZ, DQ and DP enclosures, 0.8 to 20 MHz and 3.0 to 30 MHz frequency ranges - Fundamental thickness-shear mode, AT-cut, for operation over wide temperature ranges (non-temperature controlled) - Full assessment level
|
| BS 9612 N017-1979
| 振荡器用冷焊密封石英晶体振子详细规范.DN、D2、DQ和DP外壳、0.8至20MHz和3.0到30MHz频率范围.窄温范围(非
| Detail specification for resistance welded seal quartz crystal units for oscillator applications - DN, DZ, DQ and DP enclosures, 0.8 to 20 MHz and 3.0 to 30 MHz frequency ranges - Fundamental thickness-shear mode, AT-cut, for operation over narrow temperature ranges (temperature controlled) - Full assessment level
|
| BS 9612 N018-1979
| 振荡器用电阻焊密封石英晶体振子详细规范.DN、D2、DQ和DP外壳、17至75MHz频率范围.宽温范围(非温控)操作的
| Detail specification for resistance welded seal quartz crystal units for oscillator applications - DN, DZ, DQ and DP enclosures, 17 to 75 MHz frequency range - Third overtone thickness-shear mode, AT-cut, for operation over wide temperature ranges (non-temperature controlled) - Full assessment level
|
| BS 9612 N019-1979
| 振荡器用冷焊密封石英晶体振子详细规范.DN、D2、DQ和DP外壳、17至75MHz频率范围.窄温范围(非温控)操作的第
| Detail specification for resistance welded seal quartz crystal units for oscillator applications - DN, DZ, DQ and DP enclosures, 17 to 75 MHz frequency range - Third overtone thickness-shear mode, AT-cut, for operation over narrow temperature ranges (temperature controlled) - Full assessment level
|
| BS 9612 N020-1979
| 振荡器用冷焊密封石英晶体振子详细规范.DN、D2、DQ和DP外壳、17至75MHz频率范围.宽温范围(非温控)操作的第
| Detail specification for resistance welded seal quartz crystal units for oscillator applications - DN, DZ, DQ and DP enclosures, 50 to 125 MHz frequency range - Fifth overtone thickness-shear mode, AT-cut, for operation over wide temperature ranges (non-temperature controlled) - Full assessment level
|
| BS 9612 N021-1979
| 振荡器用冷焊密封石英晶体振子详细规范.DN、D2、DQ和DP外壳、50至125MHz频率范围.窄温范围(温控)操作的第五
| Detail specification for resistance welded seal quartz crystal units for oscillator applications - DN, DZ, DQ and DP enclosures, 50 to 125 MHz frequency range - Fifth overtone thickness-shear mode, AT-cut, for operation over narrow temperature ranges (temperature controlled) - Full assessment level
|
| BS CECC 75201-1992
| 电子元器件质量评定协调体系规范.空白详细规范.临时范例.详细规范/空白详细规范.频率小于3MHz的环形连接器
| Specification for harmonized system of quality assessment for electronic components - Blank detail specification - Interim example - Detail specification/blank detail specification - Circular connectors for frequencies below 3 MHz
|
| BS CECC 75301-1992
| 电子元器件质量评定协调体系规范.空白详细规范.临时范例.详细规范/空白详细规范:频率低于3MHz的矩形连接器
| Specification for harmonized system of quality assessment for electronic components - Blank detail specification - Interim Example - Detail specification/blank detail specification: rectangular connectors for frequencies below 3 MHz
|
| BS DD IEC TS 61994-1-2003
| 频率控制和选择用压电和介电器件.术语汇编.压电和介电谐振器
| Piezoelectric and dielectric devices for frequency control and selection - Glossary - Piezoelectric and dielectric resonators
|
| BS DD IEC TS 61994-4-2-2004
| 频率控制和选择用压电和介电器件.术语汇编.压电和介电材料.压电陶瓷
| Piezoelectric and dielectric devices for frequency control and selection - Glossary - Piezoelectric and dielectric materials - Piezoelectric ceramics
|
| BS DD IEC/PAS 62431-2005
| 毫米波频率电磁波吸收装置反射率的测量方法
| Measurement methods for reflectivity of electromagnetic wave absorbers in millimetre wave frequency |
| BS EN 10303-2001
| 以中等频率使用的薄磁性钢板和带材
| Thin magnetic steel sheet and strip for use at medium frequencies
|
| BS EN 136001-1977
| 电子元件器质量评定协调体系规范.脉冲磁腔管空白详细规范.(不包括频率快变磁控管)
| Specification for harmonized system of quality assessment for electronic components - Blank detail specification: pulsed magnetrons (excluding frequency agile magnetrons)
|
| BS EN 136002-1979
| 电子元器件质量评定协调体系规范.射频加热和烹调用C、W磁控管空白详细规范.(不包括频率快变磁控管)
| Specification for harmonized system of quality assessment for electronic components - Blank detail specification: CW magnetrons for RF heating or cooking applications
|
| BS EN 14146-2004
| 天然石材试验方法.弹性的动态弹性模量测定(通过测量基本的共振频率)
| Natural stone test methods - Determination of the dynamic elastic modulus of elasticity (by measuring the fundamental resonance frequency)
|
| BS EN 175300-1997
| 电子元器件质量评定协调体系.分规范:频率3MHz以下的扁形连接器
| Harmonized system of quality assessment for electronic components - Sectional specification:rectangular connectors for frequencies below 3 MHz
|
| BS EN 50065-1-2001
| 频率范围3KHz至148.5KHz的低压电气设备信号装置规范.一般要求、频带和电磁干扰
| Specification for signalling on low-voltage electrical installations in the frequency range 3 kHz to 148.5 kHz - General requirements, frequency bands and electromagnetic disturbances
|
| BS EN 50065-2-1-2003
| 频率范围为3KHz至148.5KHz的低压电气设备的信号传输.住户、商业和轻工用工作频率范围为95kHz-148,5kHz的主
| Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 kHz to 148,5 kHz and intended for use in residential, commercial and light industrial environments
|
| BS EN 50065-2-2-2003
| 频率范围为3KHz至148.5KHz的低压电气设备的信号传输.工业用频率范围为95kHz-148,5kHz的主要通讯设备和系统
| Signalling on low voltage electrical installations in the frequency range 3 kHz to 148.5 Khz - Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 kHz to 148,5 kHz and intended for use in industrial environments
|
| BS EN 50065-2-3-2003
| 频率范围由3KHz至148.5KHz的低压电气设备的信号传输.在3kHz至95kHz频率范围内操作和由电力操作的主要通讯设
| Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Part 2-3: Immunity requirements for mains communications equipment and systems operating in the range of frequencies 3 kHz to 95 kHz and intended for use by electricity suppliers and distributors
|
| BS EN 50065-4-1-2002
| 频率范围3KHz至148.5KHz的低压电气设备信号传输.低压退耦过滤器.总规范
| Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148.5 kHz - Low voltage decoupling filters - Generic specification
|
| BS EN 50065-4-2-2002
| 频率范围为3kHz至148.5kHz的低压电气设备的信号传输.低压去耦滤波器.安全要求
| Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148.5 kHz - Low voltage decoupling filters - Safety requirements
|
| BS EN 50065-4-3-2003
| 频率范围为3kHz至148.5kHz的低压电气设备的信号传输.低压去耦滤波器.输入滤波器
| Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148.5 kHz - Low voltage decoupling filters - Incoming filter
|
| BS EN 50065-4-4-2003
| 频率范围为3kHz至148.5kHz的低压电气设备的信号传输.低压去耦滤波器.阻抗滤波器
| Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148.5 kHz - Low voltage decoupling filters - Impedance filter
|
| BS EN 50065-4-5-2003
| 频率范围为3kHz至148.5kHz的低压电气设备的信号传输.低压去耦滤波器.分段过滤器
| Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148.5 kHz - Low voltage decoupling filters - Segmentation filter
|
| BS EN 50065-4-6-2004
| 频率范围为3kHz至148.5kHz的低压电气设备的信号传输.低压退耦滤波器.相位耦合器
| Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz - Low voltage decoupling filters - Phase coulper
|
| BS EN 50065-4-7-2005
| 频率范围3KHz至148.5KHz和1.6 MHz至30 MHz的低压电气设备的信号传输.便携式低压退耦过滤器.安全要求
| Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz - Part 4-7: Portable low voltage decoupling filters - Safety requirements
|
| BS EN 50065-7-2002
| 频率范围3kHz到148.5kHz的低压电气设备上的信号传送.设备阻抗
| Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148.5 kHz - Equipment impedance
|
| BS EN 50117-5-1997
| 电缆配电网络用同轴电缆.用在频率在5MHz-2150MHz之间电网操作室内分接电缆分规范
| Coaxial cables used in cabled distribution networks - Sectional specification for indoor drop cables for use in networks operating at frequencies between 5 MHz and 2150 MHz
|
| BS EN 50117-6-1997
| 电缆配电网络用同轴电缆.用于频率在5MHz-2150MHz之间电网操作室外分接电缆分规范
| Coaxial cables used in cabled distribution networks - Sectional specification for outdoor drop cables for use in networks operating at frequencies between 5 MHz and 2150 MHz
|
| BS EN 50364-2002
| 人体暴露于0Hz-10GHz频率范围工作的电子物质监视(EAS)、射频识别(RFID)和类似用途的设备所产生的电磁场中的
| Limitation of human exposure to electromagnetic fields from devices operating in the frequency range 0 Hz to 10 GHz, used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications
|
| BS EN 50412-2-1-2005
| 用于频率在1,6 MHz到30 MHz的低压安装的输电线通信设备和系统.住宅、商业和工业环境.抗干扰性要求
| Power line communication apparatus and systems used in low-voltage installations in the frequency range 1,6 MHz to 30 MHz - Residential, commercial and industrial environment - Immunity requirements
|
| BS EN 60107-1-1997
| 电视广播传输接收机测量方法.第1部分:一般原理.显示器无线电和视频频率测量
| Methods of measurement on receivers for television broadcast transmission - General considerations - Measurements on displays at radio and video frequencies
|
| BS EN 60130-17-1999
| 频率低于3MHz的连接器.使用可充电电池的允许多向连接的互连装置的详细规范
| Connectors for frequencies below 3 MHz - Detail specification for interconnection devices which permit multi-directional mating, for use with rechargeable batteries
|
| BS EN 60130-9-2001
| 3MHz以下频率的连接器.无线电和相关音响设备的环形连接器
| Connectors for frequencies below 3 MHz - Circular connectors for radio and associated sound equipment
|
| BS EN 60156-1996
| 绝缘液.电源频率下击穿电压测定.试验验法
| Insulating liquids - Determination of the breakdown voltage at power frequency - Test method
|
| BS EN 60243-1-1998
| 固体绝缘材料介电强度试验方法.电源频率下的试验
| Methods of test for electric strength of solid insulating materials - Tests at power frequencies
|
| BS EN 60404-6-2003
| 磁性材料.使用环形样品测量磁性软金属及粉末材料在20Hz至200kHz频率范围内磁特性的方法
| Magnetic materials - Methods of measurement of the magnetic properties of magnetically soft metallic and powder materials at frequencies in the range 20 Hz to 200 kHz by the use of ring specimens
|
| BS EN 60444-4-1993
| 石英晶体元件参数测量.第4部分:30MHz以下石英晶体元件负荷谐振频率fL.负荷谐振电阻R1测量方法,以及石英晶体
| Measurement of quartz crystal unit parameters - Method for the measurement of the load resonance frequency fL, load resonance resistance RL and the calculation of other derived values of quartz crystal units, up to 30 MHz
|
| BS EN 60444-7-2004
| 石英晶体元件参数的测量.石英晶体元件的活性和频率下降的测量
| Measurement of quartz crystal unit parameters - Measurement of activity and frequency dips of quartz crystal units
|
| BS EN 60510-2-6-1996
| 卫星地面站用无线电设备测量方法.分系统测量.频率解调器
| Methods of measurement for radio equipment used in satellite earth stations - Measurements for sub-systems - Frequency demodulators
|
| BS EN 60603-10-1998
| 印制板用频率低于3MHz的连接器.倒置型2.54mm(0.1in)基本网格印制电路板用两件连接器
| Connectors for frequencies below 3 MHz for use with printed boards - Two-part connectors for printed boards for basic grid of 2 ,54 mm (0,1 in), inverted type
|
| BS EN 60603-12-1998
| 印制板用频率低于3MHz的连接器.设计用于集成电路的插座系列尺寸、一般要求和试验的详细规范
| Connectors for frequencies below 3 MHz for use with printed boards - Detail specification for dimensions, general requirements and tests for a range of sockets designed for use with integrated circuits
|
| BS EN 60603-13-1998
| 印制电路板用频率低于3MHz的连接器.不易卸绝缘可置换终端用带独立连接器的2.54mm(0.1in)基本网格印制板用经
| Connectors for frequencies below 3 MHz for use with printed boards - Detail specification for two-part connectors of assessed quality, for printed boards for basic grid of 2,54 mm (0,1 in) with free connectors for non-accessible insulation displacement terminations (ID)
|
| BS EN 60603-14-1999
| 印制板用频率低于3MHz的连接器.音频、视频和视听设备.低频声频和视频信号用环形连接器详细规范
| Connectors for frequencies below 3 MHz for use with printed boards - Detail specification for circular connectors for low-frequency audio and video applications such as audio, video and audio-visual equipment
|
| BS EN 60603-2-1998
| 印制板用频率低于3MHz的连接器.共有固定特性的2,54mm(0,1in)基本网格印制板用具有既定质量的两部连接器详细
| Connectors for frequencies below 3 MHz for use with printed boards - Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features
|
| BS EN 60603-3-1998
| 印制板用频率低于3MHz的连接器.触点中心距和交错线端子间距均为2.54mm(0.100in)的印制电路板用两对端连接器
| Connectors for frequencies below 3 MHz for use with printed boards - Two-part connectors for printed boards having contacts spaced at 2,54 mm (0,100 in) centres and staggered terminations at that same spacing
|
| BS EN 60603-4-1998
| 印制板用频率低于3MHz的连接器.触点中心间距和交错端子间距均为1·91mm(0·75in)的印制电路板用两件连接器
| Connectors for frequencies below 3 MHz for use with printed boards - Two-part connectors for printed boards having contacts spaced at 1,91 mm (0,075 in) centres and staggered terminations at that same spacing
|
| BS EN 60603-5-1998
| 印制板用频率低于3MHz的连接器.有2·54mm(0·10in)间距为2.54mm的双面印制板插座和两件连接器
| Connectors for frequencies below 3 MHz for use with printed boards - Edge-socket connectors and two-part connectors for double-sided printed boards with 2,54 mm (0,1 mm) spacing
|
| BS EN 60603-6-1998
| 印制板用频率低于3MHz的连接器.标称厚度1.6mm(0.063in)的单面或双面印制板用间隔距离为2·54mm(0·1in)插座
| Connectors for frequencies below 3 MHz for use with printed boards - Edge-socket connectors and printed board connectors with 2 ,54 mm (0,1 in) contact spacing for single or double-sided printed boards of 1,6 mm (0,063 in) nominal thickness
|
| BS EN 60603-7-1-2002
| 印制板用频率低于3MHz的连接器.具有通用配合特性的8路无屏蔽的固定连接器的详细规范
| Connectors for frequencies below 3 MHz for use with printed boards - Detail specification for 8-way, shielded free and fixed connectors with common mating features, with assessed quality
|
| BS EN 60603-7-1997
| 印制电路板频率3MHz以下的连接器. 包括有通用匹配特性经过质量评估的固定和自由连接器的8路连接器详细规范
| Connectors for frequencies below 3 MHz for use with printed boards - Detail specification for connectors, 8-way, including fixed and free connectors with common mating features, with assessed quality
|
| BS EN 60603-7-4-2005
| 电子设备连接器.数据传输频率250MHZ及以下的8位非屏蔽活动和固定连接器的详细规范
| Connectors for electronic equipment - Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz
|
| BS EN 60603-8-1998
| 印制板用频率低于3MHz的连接器.具有0.63mm×0.63mm方形插头的2.54mm(0.1in)基本网格印制电路板用两件连接器
| Connectors for frequencies below 3 MHz for use with printed boards - Two-part connectors for printed boards for basic grid of 2 ,54 mm (0,1 in), with square male contacts of 0,63 mm x 0,63 mm
|
| BS EN 60603-9-1998
| 印制板用频率低于3MHz的连接器.2.54mm(0.1in)基本网格印制电路板、底板和电缆连接器用两件连接器
| Connectors for frequencies below 3 MHz for use with printed boards - Two-part connectors for printed boards, backpanels and cable connectors, basic grid of 2,54 mm (0,1 in)
|
| BS EN 60749-12-2002
| 半导体装置.机械和气候试验方法.变频率振动
| Semiconductor devices - Mechanical and climatic test methods - Vibration, variable frequency
|
| BS EN 61000-4-16-1998
| 电磁兼容性(EMC).试验和测量技术.对0Hz-150Hz频率范围内传输的共模干扰的抗扰度试验
| Electromagnetic compatibility (EMC) - Testing and measurement techniques - Test for immunity to conducted, common mode disturbances in the frequency range 0 Hz to 150 kHz
|
| BS EN 61000-4-28-2000
| 电磁兼容性(EMC).试验和测量技术.电源频率变化和抗扰性试验
| Electromagnetic compatibility (EMC) - Testing and measurement techniques - Variation of power frequency, immunity test
|
| BS EN 61000-4-8-1994
| 电磁兼容性.第4部分:试验和测量方法.第8节:电源频率磁场抗扰试验.基本电磁兼容性(EMC)出版物
| Electromagnetic compatibility (EMC) - Testing and measurement techniques - Power frequency magnetic field immunity test - Basic EMC publication
|
| BS EN 61076-3-104-2003
| 直流低频率模拟及数字高速数据系统用的已进行过质量评定的连接器.矩形连接器.最低频率为不大于600MHz的数据
| Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications - Rectangular connectors - Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 600 MHz minimum
|
| BS EN 61076-4-102-1997
| 直流低频率模拟及高速数字数据系统用已经过过质量评定的连接器.第4部分:印制电路板联接器.第102节:带前定心
| Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications - Printed board connectors - Detail specification for two-part single-pole connectors , for multiple uses on plug-in units, with pre-centring, coding and early mating features, having a metric grid in accordance with IEC 60917
|
| BS EN 61076-5-2001
| 直流低频率模拟及高速数据数字设备用连接器.经过质量评定的串联插座.分规范
| Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications - In-line sockets with assessed quality - Sectional specification
|
| BS EN 61076-7-2001
| 直流低频率模拟及高速数字数据系统用经过质量评定的连接器.分规范
| Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications - Cable outlet accessories with assessed quality, including qualification and capability approval - Sectional specification
|
| BS EN 61094-6-2005
| 测量传声器.频率响应的测定用静电促动器
| Measurement microphones - Electrostatic actuators for determination of frequency response
|
| BS EN 61101-1994
| 在0.5MHz-15MHz频率范围使用的平面扫描技术水珍器绝对校正规范
| Specification for absolute calibration of hydrophones using the planar scanning technique in the frequency range 0,5 MHz to 15 MHz
|
| BS EN 61102-1994
| 采用频率范围为0.5MHz至15MHz的水珍器的超声波场测量和特性规范
| Specification for measurement and characterisation of ultrasonic fields using hydrophones in the frequency range 0.5 MHz to 15 MHz
|
| BS EN 61161-1995
| 液体频率范围为0.5MHz-25MHz的超声波功率测量规范
| Specification for ultrasonic power measurement in liquids in the frequency range 0.5 MHz to 25 MHz
|
| BS EN 61220-1995
| 超声波学.场.频率范围0.5MHz-15MHz超声波医疗设备含水听诊器引起的超声场的特性和测量指南
| Ultrasonics - Fields - Guidance for the measurement and characterization of ultrasonic fields generated by medical ultrasonic equipment using hydrophones in the frequency range 0.5 MHz to 15 MHz
|
| BS EN 61240-1997
| 压电装置.频率控制和选择用表面安装装置外形图绘制.总则
| Piezoelectric devices - Preparation of outline drawings of surface-mounted devices (SMD) for frequency control and selection - General rules
|
| BS EN 61334-5-1-2001
| 配电线路载波系统配电自动化.低层剖面.扩展频率漂移键控剖面
| Distribution automation using distribution line carrier systems - Lower layer profiles - The spread frequency shift keying (S-FSK) profile
|
| BS EN 61566-1998
| 射频电磁场辐照测量.频率在100kHz和1GHz间的场强
| Measurement of exposure to radio-frequency electromagnetic fields - Field strength in the frequency range 100 kHz to 1 GHz
|
| BS EN 61689-1997
| 超声波学.物理治疗系统.频率在0.5MHz和5MHz范围内的测量方法和性能要求
| Ultrasonics - Physiotherapy systems - Performance requirements and methods of measurement in the frequency range 0.5 MHz to 5 MHz
|
| BS EN 61788-7-2003
| 超导性.电子特性测量.微波频率下超导体的表面电阻
| Superconductivity - Electronic characteristic measurements - Surface resistance of superconductors at microwave frequencies
|
| BS EN 61837-1-1999
| 频率控制和选则用表面安装的压电器件.标准外形和终端引线的连接.塑性模压外壳外形
| Surface mounted piezoelectric devices for frequency control and selection - Standard outlines and terminal lead connections - Plastic moulded enclosure outlines
|
| BS EN 61837-2-2001
| 频率控制和选择用表面固定压电装置.标准外形和终端引线连接.陶瓷外壳
| Surface mounted piezoelectric devices for frequency control and selection - Standard outlines and terminal lead connections - Ceramic enclosures
|
| BS EN 61837-3-2001
| 频率控制和选择用表面安装的压电器件.标准外形和终端引线连接.金属外壳
| Surface mounted piezoelectric devices for frequency control and selection - Standard outlines and terminal lead connections - Metal enclosures
|
| BS EN 61837-4-2004
| 频率控制和选择用表面安装的压电器件.标准外形和端头连接器.混合外壳轮廓图
| Surface mounted piezoelectric devices for frequency control and selection - Standard outlines and terminal lead connections - Hybrid enclosure outlines
|
| BS EN 62092-2002
| 超声学.水听器.15MHz-40MHz频率范围内的特性和校准
| Ultrasonics - Hydrophones - Characteristics and calibration in the frequency range from 15 MHz to 40 MHz
|
| BS EN 62106-2003
| 频率范围为87.5-108.0MHz的VHF/FM有声广播用无线电数据系统(RDS)的规范
| Specification of the radio data system (RDS) for VHF/FM sound broadcasting in the frequency range from 87,5 to 108,0 MHz
|
| BS EN ISO 2247-2003
| 包装.满装的运输包装件和单件荷载.固定低频率振动试验
| Packaging - Complete, filled transport packages and unit loads - Vibration tests at fixed low frequency
|
| BS EN ISO 266-1997
| 声学.优选频率
| Acoustics - Preferred frequencies
|
| BS EN ISO 389-5-1998
| 声学.听力测定设备校准的标准参考零点.频率范围为8kHz至16kHz之间的纯音用参考等效阈声压级
| Acoustics - Reference zero for the calibration of audiometric equipment - Reference equivalent threshold sound pressure levels for pure tones in the frequency range 8 kHz to 16 kHz
|
| BS EN ISO/IEC 7487-1-1995
| 信息技术.以限定的频率7958次磁通变换/弧度和1.9次变换/mm(48次变换/in)在两侧调制录制的130mm(5.25in)盒式
| Information technology - Data interchange on 130mm (5,25 in) flexible disk cartridges using modified frequency modulation recording at 7 958 ftprad, 1,9 tpmm (48 tpi), on both sides - ISO type 202 - Dimensional, physical and magnetic characteristics
|
| BS IEC 60747-16-2-2001
| 半导体装置和集成电路.微波集成电路.频率预定标器
| Discrete semiconductor devices and integrated circuits - Microwave integrated circuits - Microwave integrated circuits - Frequency prescalers
|
| BS ISO 11093-8-1998
| 纸和纸板.芯层试验.通过试验模型分析法对自然频率和弯曲模量的测定
| Paper and board - Testing of cores - Determination of natural frequency and flexural modulus by experimental modal analysis
|
| BS ISO 15186-3-2002
| 声学.利用声强度测量建筑物和建筑部件的隔音性能.低频率实验室测量
| Acoustics - Measurement of sound insulation in buildings and of building elements using sound intensity - Laboratory measurements at low frequencies
|
| BS QC 030000-1993
| 电子元器件质量评估协调体系.频率小于3MHz的矩形连接器.经质量评定的连接器用详细规范编写的一般要求和指南
| Harmonized system of quality assessment for electronic components - Rectangular connectors for frequencies below 3 MHz - Generic specification - General requirements and guide for the preparation of detail specifications for connectors with assessed quality
|
| DD IEC/PAS 62260-2001
| 反向不连续傅里叶传输的频率区域内脉冲/分步回损测量
| Pulse/step return loss from measurement in the frequency domain using the inverse discrete fourier transformation (IDFT)
|
| TH 20338-2002
| 世界电力供应.电压和频率
| World Electricity Supplies - Voltages and frequencies
|
| 编号 | 中文名称 | 英文名称 |
|---|