编号 | 中文名称 | 英文名称 |
BS 2952-1958
| 内燃机冷却系统用橡胶软管规范
| Specification for rubber hose for i.c. engine cooling systems
|
BS 3092-1973
| 内燃机主摩擦离合器、主动力输出装置及其有关附件的规范
| Specification for main friction clutches, main power-take-off assemblies and associated attachments for internal combustion engines
|
BS 3529-1962
| 内燃机用飞轮箱安装垫和托架的尺寸规范
| Specification for dimensions of flywheel housing mounting pads and brackets for i.c. engines
|
BS 3818-1964
| 柴油机车及有轨内燃机车自动密封加油接头规范
| Specification for self-sealing fuelling couplings for diesel locomotives and diesel railcars
|
BS 3928-1969
| 空气过滤器的钠焰试验方法(为内燃机和压缩机供气用的除外)
| Method for sodium flame test for air filters (other than for air supply to I.C. engines and compressors)
|
BS 5000-3-1980
| 特种或专用旋转电机规范.第3部分:往复式内燃机驱动发电机
| Specification for rotating electrical machines of particular types or for particular applications - Generators to be driven by reciprocating internal combustion engines
|
BS 5208-1975
| 小型内燃机用动力输出轴和安装面的尺寸规范
| Specification for dimensions of power take-off driving shafts and mounting faces for small internal combustion engines
|
BS 5341-5-1976
| 往复式内燃机用直径小于等于200mm的活塞环.第5部分:环槽
| Piston rings up to 200 mm diameter for reciprocating internal combustion engines - Ring grooves
|
BS 5341-6.1-1992
| 往复式内燃机直径小于等于200mm的活塞环.第6部分:术语、检验方法和通用规范.第1集;术语
| Piston rings up to 200 mm diameter for reciprocating internal combustion engines - Vocabulary, inspection methods and generic specifications - Vocabulary
|
BS 5341-7.3.1-1992
| 往复式内燃机直径小于等于200mm的活塞环.第7部分:单片环的设计、尺寸和命名.第3节:楔表面和半楔表面压缩环.
| Piston rings up to 200 mm diameter for reciprocating internal combustion engines - Designs, dimensions and designations for single piece rings - Keystone and half keystone compression rings - Specification for keystone rings
|
BS 5341-7.4-1992
| 往复式内燃机直径小于等于200mm的活塞环.第7部分:单片环设计、尺寸和命名.第4节:控油环规范
| Piston rings up to 200 mm diameter for reciprocating internal combustion engines - Designs, dimensions and designations for single piece rings - Specification for oil control rings
|
BS 5341-8.1-1992
| 往复式内燃机直径小于等于200mm的活塞环.第8部分:多片组合式控油环设计、尺寸和命名.第1节:盘簧加压控油环
| Piston rings up to 200 mm diameter for reciprocating internal combustion engines - Designs, dimensions and designations for multi-piece oil control rings - Specification for coil-spring-loaded oil control rings
|
BS 5514-4-1997
| 往复式内燃机规范.性能.第4部分:转速调节
| Reciprocating internal combustion engines - Performance - Speed governing
|
BS 5514-6-1992
| 往复式内燃机.性能.第6部分:过速保护规范
| Reciprocating internal combustion engines - Performance - Specification for overspeed protection
|
BS 5514-7-1996
| 往复式内燃机性能.第7部分:发动机功率规程
| Reciprocating internal combustion engines: performance - Codes for engine power
|
BS 5672-1991
| 往复式内燃机汽缸头的汽缸和阀旋转方向标示和左、右单列发动机定义的规范
| Specification for designation of the direction of rotation and of cylinders and valves in cylinder heads, and definition of right-hand and left-hand in-line engines and locations on an engine for reciprocating internal combustion engines
|
BS 6327-1982
| 往复式内燃机防火规范
| Specification for fire protection of reciprocating internal combustion engines
|
BS 7016-1-1988
| 往复式内燃机部件和系统.第1部分:结构与外壳的术语词汇
| Components and systems of reciprocating internal combustion engines - Glossary of terms for structure and external covers
|
BS 7016-2-1988
| 往复式内燃机部件和系统.第2部分:主动齿轮的术语词汇
| Components and systems of reciprocating internal combustion engines - Glossary of terms for main running gear
|
BS 7016-3-1988
| 往复式内燃机部件和系统.第3部分:阀门、凸输轴传动和驱动机构的术语词汇
| Components and systems of reciprocating internal combustion engines - Glossary of terms for valves, camshaft drive and actuating mechanisms
|
BS 7016-9-1997
| 往复式内燃机的部件和系统.控制和监测系统
| Components and systems of reciprocating internal combustion engines - Control and monitoring systems
|
BS 7328-1990
| 模型蒸汽发动机和内燃机规范
| Specification for model steam engines and internal combustion engines for models
|
BS 7403-1-1998
| 内燃机满液流润滑油过滤器.不同压力/流量特性试验方法
| Full-flow lubricating oil filters for internal combustion engines - Methods of test for differential pressure/flow characteristics
|
BS 7403-11-1998
| 内燃机用全流式润滑油过滤器.自洁式过滤器的试验方法
| Full-flow lubricating oil filters for internal combustion engines - Methods of test for self-cleaning filters
|
BS 7403-12-2000
| 内燃机全流量润滑油滤清器.用颗粒计数确定过滤效率 ,污染抑制能力
| Full-flow lubricating oil filters for internal combustion engines - Filtration efficiency using particle counting, and contaminant retention capacity
|
BS 7403-2-1998
| 内燃机满液流润滑油过滤器.元件分支阀特性试验方法
| Full-flow lubricating oil filters for internal combustion engines - Method of test for element by-pass valve characteristics
|
BS 7403-3-1998
| 内燃机满流式润滑油过滤器.第3部分:耐高压差和耐高温性能试验方法
| Full-flow lubricating oil filters for internal combustion engines - Methods of test for resistance to high differential pressure and to elevated temperature
|
BS 7403-4-1998
| 内燃机满液流式润滑油过滤器.初始微粒滞留效率、寿命和累积效率试验方法(重力法)
| Full-flow lubricating oil filters for internal combustion engines - Methods of test for initial particle retention efficiency, life and cumulative efficiency (gravimetric method)
|
BS 7403-5-1991
| 内燃机用全流式润滑油过滤器.第5部分:冷起动摸拟和液压脉冲耐久性的试验方法
| Full-flow lubricating oil filters for internal combustion engines - Method of test for cold start simulation and hydraulic pulse durability
|
BS 7403-6-1991
| 内燃机用全流式润滑油过滤器.第6部分:静态爆裂压力的试验方法
| Full-flow lubricating oil filters for internal combustion engines - Method of test for static burst pressure
|
BS 7403-7-1991
| 内燃机用全流式润滑油滤清器.第7部分:振动疲劳试验方法
| Full-flow lubricating oil filters for internal combustion engines - Method of test for vibration fatigue
|
BS 7403-9-1995
| 内燃机用全流式润滑油过滤器.入口和出口防泄油阀试验方法
| Full-flow lubricating oil filters for internal combustion engines - Method of test for inlet and outlet anti-drain valves
|
BS 7698-10-1999
| 往复式内燃机驱动交流发电机组.用包络表面法对空气中噪音进行测定
| Reciprocating internal combustion engine driven alternating current generating sets - Measurement of airborne noise by the enveloping surface method
|
BS 7698-12-1998
| 往复式内燃机驱动交流发电设备.安全装置的应急供电
| Reciprocating internal combustion engine driven alternating current generating sets - Emergency power supply to safety devices
|
BS 7698-7-1996
| 往复式内燃机驱动的交流发电机组.规范和设计的技术申报
| Reciprocating internal combustion engine driven alternating current generating sets - Technical declarations for specification and design
|
BS 7698-8-1996
| 往复式内燃机驱动的交流发电机组.低功率发电机组要求和试验
| Reciprocating internal combustion engine driven alternating current generating sets - Requirements and tests for low-power generating sets
|
BS 7698-9-1996
| 往复式内燃机驱动的交流发电机组.机械振动的测量和评估
| Reciprocating internal combustion engine driven alternating current generating sets - Measurement and evaluation of mechanical vibrations
|
BS AU 226-1988
| 活塞式内燃机用飞轮箱标称尺寸和公差规范
| Specification for nominal dimensions and tolerances of flywheel housings for reciprocating internal combustion engines
|
BS AU 249-1993
| 往复式内燃机离合器外壳规范.标称尺寸和公差
| Specification for clutch housings for reciprocating internal combustion engines - Nominal dimensions and tolerances
|
BS CWA 15145-2004
| 机动车燃料.内燃机用柴油乳剂中的水.要求和试验方法
| Automotive fuels - Water in diesel fuel emulsions for use in internal combustion engines - Requirements and test methods
|
BS DD 208-1992
| 往复式内燃机用的直径为200mm及其以下的活塞环:窄环宽度的矩形截面活塞环的规范
| Piston rings up to 200 mm diameter for reciprocating internal combustion engines: specification for rectangular rings with narrow ring width
|
BS DD 209-1992
| 往复式内燃机用的直径为200mm及其以下的活塞环:半梯形活塞环规范
| Piston rings up to 200 mm diameter for reciprocating internal combustion engines: specification for half keystone rings
|
BS EN 10090-1998
| 内燃机用阀门钢和合金
| Valve steels and alloys for internal combustion engines
|
BS EN 1175-2-1998
| 工业货车安全.电气要求.装有内燃机货车的一般要求
| Safety of industrial trucks - Electrical requirements - General requirements for internal combustion engine powered trucks
|
BS EN 1175-3-1998
| 工业货车安全.电气要求.装有内燃机货车的供电系统特殊要求
| Safety of industrial trucks - Electrical requirements - Specific requirements for the electric power transmission systems of internal combustion engine powered trucks
|
BS EN 1679-1-1998
| 往复式内燃机.安全.压燃式发动机
| Reciprocating internal combustion engines - Safety - Compression ignition engines
|
BS EN 55012-2002
| 车辆,船舶,内燃机驱动装置.无线电干扰特性.(不包括那些在车辆/小船/驱动装置中自身安装的接收机或其附近车
| Vehicles, boats and internal combustion engine driven devices - Radio disturbance characteristics - Limits and methods of measurement for the protection of receivers except those installed in the vehicle/boat/device itself or in adjacent vehicles/boats/devices
|
BS EN 60034-22-1998
| 旋转电机.往复式内燃机(RIC)引擎驱动交流发电机.
| Rotating electrical machines - A.C. generators for reciprocating internal combustion (RIC) engine driven generating sets
|
BS EN 88528-11-2004
| 往复式内燃机驱动交流发电机组.旋转不间断电力系统.性能要求和试验方法
| Reciprocating internal combustion engine driven alternating current generating sets - Rotary uninterruptible power systems - Performance requirements and test methods
|
BS EN ISO 11102-1-1997
| 内燃机.手柄起动装置.安全要求和检验
| Reciprocating internal combustion engines - Handle starting equipment - Safety requirements and tests
|
BS EN ISO 11102-2-1997
| 往复式内燃机.手柄起动装置.脱离角度的试验方法
| Reciprocating internal combustion engines - Handle starting equipment - Method of testing the angle of disengagement
|
BS EN ISO 11680-1-2001
| 林业机械.动力杆驱动的修枝锯的安全要求和试验.带有整体内燃机的装置
| Machinery for forestry - Safety requirements and testing for pole-mounted powered pruners - Units fitted with an integral combustion engine
|
BS EN ISO 11806-1997
| 农林机械.内燃机驱动的便携手持式灌木铲除机和割草机.安全
| Agricultural and forestry machinery - Portable hand-held combustion engine driven brush cutters and grass trimmers - Safety
|
BS EN ISO 14314-2004
| 往复式内燃机.反冲起动设备.一般安全要求
| Reciprocating internal combustion engines - Recoil starting equipment - General safety requirements
|
BS EN ISO 22868-2005
| 林用机械.带内燃机的便携手持式机械的噪声试验规范.工程法(2级准确度)
| Forestry machinery - Noise test code for portable hand-held machines with internal combustion engine - Engineering method (grade 2 accuracy)
|
BS EN ISO 8178-1-1996
| 往复式内燃机.排放污染测定.气态和颗粒状排放污染物的试验台测定法
| Reciprocating internal combustion engines - Exhaust emission measurement - Test-bed measurement of gaseous and particulate exhaust emissions
|
BS EN ISO 8178-2-1997
| 往复式内燃机.排气污染测定.气态和颗粒状排放污染物的定点测量
| Reciprocating internal combustion engines - Exhaust emission measurement - Measurement of gaseous and particulate exhaust emissions at site
|
BS EN ISO 8178-4-1996
| 往复式内燃机.排放污染测定.不同发动机应用的试验周期
| Reciprocating internal combustion engines - Exhaust emission measurement - Test cycles for different engine applications
|
BS EN ISO 8178-5-1997
| 往复式内燃机排放物污染指数的测定.第5部分:燃料试验
| Reciprocating internal combustion engines - Exhaust emission measurement - Test fuels
|
BS EN ISO 8178-6-2001
| 往复式内燃机.废气排放测定.测量结果和试验报告
| Reciprocating internal combustion engines - Exhaust emission measurement - Report of measuring results and tests - Part 6 : Report of measuring results and tests
|
BS EN ISO 9785-2002
| 船舶和海上技术.可行驶内燃机机动车的货舱空间的通风.需要的总气流量的理论计算
| Ship and marine technology - Ventilation of cargo spaces where vehicles with internal combustion engines are driven - Calculation of theoretical total airflow required
|
BS ISO 11424-1997
| 内燃机气动系统和真空系统用橡胶软管和导管.规范
| Rubber hoses and tubing for air and vacuum systems for internal-combustion engines - Specification
|
BS ISO 13332-2001
| 往复式内燃机.在发动机底座处测量的由高速和中速往复式内燃机产生的结构噪声的试验规程
| Reciprocating internal combustion engines - Test code for the measurement of structure-borne noise emitted from high-speed and medium-speed reciprocating internal combustion engines measured at the engine feet
|
BS ISO 13738-2000
| 润滑剂、工业用油和有关制品(L类).E系列(内燃机油).两冲程汽油发动机油(类别EGB、EGC和EGD) 规范
| Lubricants, industrial oils and related products (class L) - Family E (internal combustion engine oils) - Specifications for two-stroke-cycle gasoline engine oils (categories EGB, EGC and EGD)
|
BS ISO 13774-1999
| 输送内燃机燃料用橡胶和塑料软管.易燃性试验方法
| Rubber and plastics hoses for fuels for internal combustion engines - Method of test for flammability
|
BS ISO 14396-2002
| 往复式内燃机.内燃机功率的测定和内燃机功率测量的试验方法.符合ISO 8178的废气排放试验的补充要求
| Reciprocating internal combustion engines - Determination and method for the measurement of engine power - Additional requirements for exhaust emission tests in accordance with ISO 8178
|
BS ISO 14865-1998
| 林业用机械.背包式内燃机电源便携式手持灌木切割机和剪草机.安全要求和试验
| Machinery for forestry - Portable hand-held brush cutters and grass trimmers with backpack mounted combustion engine power source - Safety requirements and testing
|
BS ISO 15550-2002
| 内燃机.测量发动机功率的测定方法.总要求
| Internal combustion engines - Determination and method for the measurement of engine power - General requirements
|
BS ISO 18669-1-2005
| 内燃机.活塞销.一般规范
| Internal combustion engines - Pistons pins - General specifications
|
BS ISO 18669-2-2005
| 内燃机.活塞销.检验测量原理
| Internal combustion engines - Pistons pins - Inspection measuring principles
|
BS ISO 19013-2-2005
| 内燃机燃料回路用橡胶软管和管.规范.汽油燃料
| Rubber hoses and tubing for fuel circuits for internal combustion engines - Specification - Gasoline fuels
|
BS ISO 19438-2004
| 内燃机用柴油燃料和汽油过滤器.用粒子计数和污物滞留量测定过滤效率
| Diesel fuel and petrol filters for internal combustion engines - Filtration efficiency using particle counting and contaminant retention capacity
|
BS ISO 2261-1996
| 往复式内燃机.手操纵装置.运动的标准方向
| Reciprocating internal combustion engines - Hand-operated control devices - Standard direction of motion
|
BS ISO 2710-1-2000
| 往复式内燃机.词汇.发动机设计和运行术语
| Reciprocating internal combustion engines - Vocabulary - Terms for engine design and operation
|
BS ISO 2710-2-2000
| 往复式内燃机.词汇.发动机维修术语
| Reciprocating internal combustion engines - Vocabulary - Terms for engine maintenance
|
BS ISO 3046-1-2002
| 往复式内燃机.性能.功率、燃料消耗量和润滑油消耗量和试验方法说明.通用内燃机的附加要求
| Reciprocating internal combustion engines - Performance - Declarations of power, fuel and lubricating oil consumptions, and test methods - Additional requirements for engines for general use
|
BS ISO 3046-5-2002
| 往复式内燃机.性能.扭转振动
| Reciprocating internal combustion engines - Performance - Torsional vibrations
|
BS ISO 5011-2001
| 内燃机和压缩机的空气进气清洁装置.性能测试
| Inlet air cleaning equipment for internal combustion engines and compressors - Performance testing
|
BS ISO 6415-2005
| 内燃机.润滑油用旋压式过滤器.尺寸
| Internal combustion engines - Spin-on filters for lubricating oil - Dimensions
|
BS ISO 6621-2-2004
| 内燃机.活塞环.检验测量规则
| Internal combustion engines - Piston rings - Inspection measuring principles
|
BS ISO 6621-4-2003
| 内燃机.活塞环.一般规范
| Internal combustion engines - Piston rings - General specifications
|
BS ISO 6621-5-2006
| 内燃机.活塞环.质量要求
| Internal combustion engines - Piston rings - Quality requirements
|
BS ISO 6622-1-2003
| 内燃机.活塞环.铸铁制矩形环
| Internal combustion engines - Piston rings - Rectangular rings made of cast iron
|
BS ISO 6622-2-2003
| 内燃机.活塞环.钢制矩形环
| Internal combustion engines - Piston rings - Rectangular rings made of steel
|
BS ISO 6623-2004
| 内燃机.活塞环.铸铁制刮环
| Internal combustion engines - Piston rings - Scraper rings made of cast iron
|
BS ISO 6624-2-2003
| 内燃机.活塞环.铸铁制半梯形环
| Internal combustion engines - Piston rings - Half keystone rings made of cast iron
|
BS ISO 6624-4-2003
| 内燃机.活塞环.钢制半梯形环
| Internal combustion engines - Piston rings - Half keystone rings made of steel
|
BS ISO 6798-1996
| 往复式内燃机.空气传播噪声的测量.工程法和测量法
| Reciprocating internal combustion engines - Measurement of emitted airborne noise - Engineering method and survey method
|
BS ISO 7967-4-2005
| 往复式内燃机.零部件和系统词汇.增压及进/排气管道系统
| Reciprocating internal combustion engines - Vocabulary of components and systems - Pressure charging and air/exhaust gas ducting systems
|
BS ISO 7967-5-2003
| 往复式内燃机.零件和系统的词汇.冷却系统
| Reciprocating internal combustion engines - Vocabulary of components and systems - Cooling systems
|
BS ISO 7967-6-2005
| 往复式内燃机.零部件和系统词汇.润滑系统
| Reciprocating internal combustion engines - Vocabulary of components and systems - Lubricating systems
|
BS ISO 7967-7-2005
| 往复式内燃机.零部件和系统词汇.调节系统
| Reciprocating internal combustion engines - Vocabulary of components and systems - Governing systems
|
BS ISO 7967-8-2005
| 往复式内燃机.零部件和系统词汇.起动系统
| Reciprocating internal combustion engines - Vocabulary of components and systems - Starting systems
|
BS ISO 8178-10-2003
| 往复式内燃机.排放测量.压燃式发动机瞬态工况时排气烟度现场测量用试验周期和试验方法
| Reciprocating internal combustion engines - Exhaust emission measurement - Test cycles and test procedures for field measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions
|
BS ISO 8178-3-1996
| 往复式内燃机.废气排放测量.第3部分:在稳定状态下废气黑烟排放测量定义和方法
| Reciprocating internal combustion engines - Exhaust emission measurement - Definitions and methods of measurement of exhaust gas smoke under steady state conditions
|
BS ISO 8178-7-1997
| 往复式内燃机.废气排放测量.第7部分:发动机系列测定
| Reciprocating internal combustion engines - Exhaust emission measurement - Engine family determination
|
BS ISO 8178-8-1997
| 往复式内燃机.废气排放测量.第7部分:发动机成组测定
| Reciprocating internal combustion engines - Exhaust emission measurement - Engine group determination
|
BS ISO 8178-9-2001
| 往复式内燃机.排放测量.压燃式发动机瞬态工况排气烟度试验台测量用试验周期和试验方法
| Reciprocating internal combustion engines - Exhaust emission measurement - Test cycles and test procedures for test-bed measurement of exhaust gas smoke emissions from compression ignition engines operating under transi ent conditions
|
BS ISO 8528-1-2006
| 往复式内燃机驱动的交流发电机组.应用、额定功率和性能
| Reciprocating internal combustion engine driven alternating current generating sets - Application, ratings and performance |
BS ISO 8528-2-2006
| 往复式内燃机驱动的交流发电装置.发动机
| Reciprocating internal combustion engine driven alternating current generating sets - Engines
|
BS ISO 8528-3-2006
| 往复式内燃机驱动的交流发电装置.发电机组的交流发电机
| Reciprocating internal combustion engine driven alternating current generating sets - Alternating current generators for generating sets
|
BS ISO 8528-4-2006
| 往复式内燃机驱动的交流发电装置.控制设备和开关设备
| Reciprocating internal combustion engine driven alternating current generating sets - Controlgear and switchgear
|
BS ISO 8528-5-2006
| 往复式内燃机驱动的交流发电装置.发电装置
| Reciprocating internal combustion engine driven alternating current generating sets - Generating sets
|
BS ISO 8528-6-2006
| 往复式内燃机驱动的交流发电装置.试验方法
| Reciprocating internal combustion engine driven alternating current generating sets - Test methods
|
DD 208-1992
| 往复式内燃机用最大直径为200mm的活塞环:带有窄环宽度的矩形截面活塞环规范
| Piston rings up to 200 mm diameter for reciprocating internal combustion engines: specification for rectangular rings with narrow ring width
|
DD 209-1992
| 往复式内燃机用最大直径为200mm的活塞环:半梯形截面活塞环规范
| Piston rings up to 200 mm diameter for reciprocating internal combustion engines: specification for half keystone rings
|
编号 | 中文名称 | 英文名称 |