| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| BS 1486-1-1959 | 润滑脂管嘴.第1部分:机械与车辆用润滑脂管嘴和适配器 | Lubricating nipples - Lubricating nipples and adaptors for use on machinery and vehicles |
| BS 1486-2-1961 | 润滑脂管嘴.重型润滑脂管嘴 | Lubricating nipples - Heavy duty lubricating nipples |
| BS 1486-4-1981 | 润滑脂管嘴规范.第4部分:液压润滑脂管嘴规范 | Lubricating nipples - Specification for hydraulic grease nipples |
| BS 2000-112-2005 | 石油及其产品的试验方法.测定润滑脂对铜腐蚀性.铜片法 | Methods of test for petroleum and its products - Part 112: Determination of corrosiveness to copper of lubricating grease - Copper strip method (Identical with IP 112:2005) |
| BS 2000-121-2005 | 石油及其产品的试验方法.从润滑脂中分离油的测定.压力过滤法 | Methods of test for petroleum and its products - Part 121: Determination of oil separation from lubricating grease - Pressure filtration method (Identical with IP 121:2005) |
| BS 2000-132-1996 | 石油和石油产品试验方法.石油产品.第132部分.润滑脂.滴点测定 | Methods of test for petroleum and its products - Petroleum products - Lubricating grease - Determination of dropping point |
| BS 2000-139-1998 | 石油及石油产品试验方法.第220部分:石油产品和润滑剂.酸值或碱值测定.颜色指示剂滴定法 | Methods of test for petroleum and its products - Petroleum products and lubricants - Determination of acid or base number - Colour-indicator titration method |
| BS 2000-142-1993 | 石油和石油产品的试验方法.润滑脂氧化稳定性的测定.氧弹法 | Methods of test for petroleum and its products - Determination of oxidation stability of lubricating grease - Oxygen bomb method |
| BS 2000-149-1993 | 石油和石油产品的试验方法.石油产品.润滑油和添加剂.磷含量的测定.喹啉磷钼酸盐法 | Methods of test for petroleum and its products - Part 149. Petroleum products - Lubricating oils and additives - Determination of phosphorus content - Quinoline phosphomolybdate method (Identical with IP 149/93) |
| BS 2000-163-1996 | 石油和石油产品试验方法.石油产品.第163部分:润滑油和添加剂.硫酸盐灰分测定 | Methods of test for petroleum and its products - Petroleum products - Lubricating oils and additives - Determination of sulfated ash |
| BS 2000-168-2003 | 石油及其产品试验方法.润滑脂滚动轴承性能测定 | Methods of test for petroleum and its products - Part 168: Determination of rolling bearing performance of lubricating grease (Identical with IP 168:2003) |
| BS 2000-19-2003 | 石油及其产品的试验方法.润滑油的反乳化性能测定 | Methods of test for petroleum and its products - Part 19: Determination of demulsibility characteristics of lubricating oil (Identical with IP 19:2003) |
| BS 2000-220-1998 | 石油及石油产品试验方法.第220部分:石油产品和润滑剂.润滑脂防锈特性测定 | Methods of test for petroleum and its products - Petroleum products and lubricants - Determination of rust-prevention characteristics of lubricating greases |
| BS 2000-280-1999 | 石油及其产品的试验方法.石油产品和润滑剂.抗氧化剂涡轮机矿物油.氧化稳定性的测定 | Methods of test for petroleum and its products - Petroleum products and lubricants - Inhibited mineral turbine oils - Determination of oxidation stability |
| BS 2000-313-2001 | 石油和石油产品的试验方法.液压油和润滑油的释气值测定 | Methods of test for petroleum and its products - BS 2000-313:2001 Determination of air release of lubricating and hydraulic oils (Identical with IP 313:2001) |
| BS 2000-346-1996 | 石油和石油产品试验方法.第102部分:未用的润滑基油和不含沥青烯的石油馏分物中多环芳香族环烃的测定.二甲硫 | Methods of test for petroleum and its products - Determination of polycyclic aromatics in unused lubricating base oils and asphaltene free petroleum fractions - Dimethyl sulphoxide extraction refractive index method |
| BS 2000-450-2000 | 石油及其制品的试验方法.柴油.用高频往复式装置评定燃油的润滑性.试验方法 | Methods of test for petroleum and its products - Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Test method |
| BS 2000-48-1997 | 石油及其制品的试验方法.润滑油的氧化特性的测定 | Methods of test for petroleum and its products - Determination of oxidation characteristics of lubricating oil |
| BS 2000-50-1993 | 石油和石油产品的试验方法.润滑脂的锥入度测定 | Methods of test for petroleum and its products - Determination of cone penetration of lubricating grease |
| BS 2464-1954 | 汽油、石油和润滑剂用软管接头(标称尺寸 1/4英寸至 4英寸)规范 | Specification for hose couplings for petrol, oil and lubricants (3/4 in. to 4 in. nominal sizes) |
| BS 2464-2-1969 | 石油、汽油和润滑油用软管接头规范.第2部分:高压接头 | Specification for hose couplings for petrol, oil and lubricants - High pressure couplings |
| BS 2464-3-1968 | 汽油、石油和润滑剂用软管接头规范.第3部分:快速接头 | Specification for hose couplings for petrol, oil and lubricants - Quick-acting couplings |
| BS 2464-4-1980 | 汽油、石油和润滑剂用软管接头规范.第4部分:欧洲型 100mm快速接头规范 | Hose couplings for petrol, oil and lubricants - Specification for 100 mm quick-acting couplings: European type |
| BS 2626-1992 | 制冷压缩机用润滑油规范 | Specification for lubricants for refrigerant compressors |
| BS 2F 67-1980 | 航空燃料和发动机润滑油用软管规范 | Specification for hose for aviation fuel and engine lubricating oil for aeronautical purposes |
| BS 3919-1987 | 工业用牛脂与动物润滑脂规范 | Specification for technical tallow and animal grease |
| BS 4231-1992 | 工业液体润滑剂粘度等级分类 | Classification for viscosity grades of industrial liquid lubricants |
| BS 4475-2000 | 纯矿物润滑油规范 | Specification for straight mineral lubricating oils |
| BS 489-1999 | 涡轮机润滑剂规范 | Specification for turbine lubricants |
| BS 5077-1974 | 同BS 4507规定的润滑脂筒配合使用的润滑脂枪(手动操作杆型)规范 | Specification for grease guns (hand-operated lever type) for use with cartridges complying with BS 4507 |
| BS 5739-1979 | 机床润滑油说明书的表示方法 | Method of presentation of lubrication instructions for machine tools |
| BS 6005-1997 | 压缩空气过滤器和润滑器用透明聚碳酸模塑杯规范 | Specification for moulded transparent polycarbonate bowls used in compressed air filters and lubricators |
| BS 6413-2-1983 | 润滑剂、工业用油和相关产品(L级).第2部分:F系列的分类(主轴轴承、轴承和相关离合器) | Lubricants, industrial oils and related products (class L) - Classification for family F (spindle bearings, bearings and associated clutches) |
| BS 6413-6-1991 | 润滑油、工业用油和有关产品(L类).C系列(齿轮)用分类 | Lubricants, industrial oils and related products (class L) - Classification for family C (gears) |
| BS 6413-7-1988 | 润滑剂、工业用油和相关产品(L级).第7部分:M系列分类(金属加工) | Lubricants, industrial oils and related products (class L) - Classification for family M (metalworking) |
| BS 6413-8-1988 | 润滑剂、工业用油和相关产品(L级).第8部分:R系列分类(暂时防腐保护) | Lubricants, industrial oils and related products (class L) - Classification for family R (temporary protection against corrosion) |
| BS 6913-13-1997 | 运土机械的操作和维修.润滑油配件规范.油嘴类型 | Operation and maintenance of earth-moving machinery - Specification for lubrication fittings - Nipple type |
| BS 6913-14-1997 | 运土机械的操作和维修.润滑油配件规范.注油抢喷嘴 | Operation and maintenance of earth-moving machinery - Specification for lubrication fittings - Grease-gun nozzles |
| BS 7033-2-1989 | 拭擦布和抛光布.第2部分:清洁或润滑用再生材料和废纺纱的工业擦拭物规范 | Cleaning and polishing cloths - Specification for industrial wipers from reclaimed materials, and waste yarn for cleaning and lubricating purposes |
| BS 7403-1-1998 | 内燃机满液流润滑油过滤器.不同压力/流量特性试验方法 | Full-flow lubricating oil filters for internal combustion engines - Methods of test for differential pressure/flow characteristics |
| BS 7403-11-1998 | 内燃机用全流式润滑油过滤器.自洁式过滤器的试验方法 | Full-flow lubricating oil filters for internal combustion engines - Methods of test for self-cleaning filters |
| BS 7403-12-2000 | 内燃机全流量润滑油滤清器.用颗粒计数确定过滤效率 ,污染抑制能力 | Full-flow lubricating oil filters for internal combustion engines - Filtration efficiency using particle counting, and contaminant retention capacity |
| BS 7403-2-1998 | 内燃机满液流润滑油过滤器.元件分支阀特性试验方法 | Full-flow lubricating oil filters for internal combustion engines - Method of test for element by-pass valve characteristics |
| BS 7403-3-1998 | 内燃机满流式润滑油过滤器.第3部分:耐高压差和耐高温性能试验方法 | Full-flow lubricating oil filters for internal combustion engines - Methods of test for resistance to high differential pressure and to elevated temperature |
| BS 7403-4-1998 | 内燃机满液流式润滑油过滤器.初始微粒滞留效率、寿命和累积效率试验方法(重力法) | Full-flow lubricating oil filters for internal combustion engines - Methods of test for initial particle retention efficiency, life and cumulative efficiency (gravimetric method) |
| BS 7403-5-1991 | 内燃机用全流式润滑油过滤器.第5部分:冷起动摸拟和液压脉冲耐久性的试验方法 | Full-flow lubricating oil filters for internal combustion engines - Method of test for cold start simulation and hydraulic pulse durability |
| BS 7403-6-1991 | 内燃机用全流式润滑油过滤器.第6部分:静态爆裂压力的试验方法 | Full-flow lubricating oil filters for internal combustion engines - Method of test for static burst pressure |
| BS 7403-7-1991 | 内燃机用全流式润滑油滤清器.第7部分:振动疲劳试验方法 | Full-flow lubricating oil filters for internal combustion engines - Method of test for vibration fatigue |
| BS 7403-9-1995 | 内燃机用全流式润滑油过滤器.入口和出口防泄油阀试验方法 | Full-flow lubricating oil filters for internal combustion engines - Method of test for inlet and outlet anti-drain valves |
| BS 7786-2006 | 航空航天系列.MoS2润滑的耐热钢制自锁六角螺母.等级1100 MPa (环境温度)315℃ | Specification for unsintered PTFE tapes for general use |
| BS DD ISO/TS 23556-2007 | 去除润滑油中柴油机烟灰用装置的性能试验方法.初始过滤效率 | Performance test method for diesel engine soot-removal devices in lubricating oils - Initial filtration efficiency |
| BS EN 12081-1998 | 铁路设施.车箱体.润滑脂 | Railway applications - Axleboxes - Lubricating greases |
| BS EN 12634-1999 | 石油产品和润滑剂.酸值测定.无水电势滴定法 | Petroleum products and lubricants - Determination of acid number - Non-aqueous potentiometric titration method |
| BS EN 14865-2-2006 | 铁路设施.轴套润滑油.确保机车速度达到200km/h的机械稳定性试验的方法 | Railway applications - Axlebox lubricating greases - Method to test the mechanical stability to cover vehicle speeds up to 20 0 km/h |
| BS EN 15199-1-2006 | 石油产品.用气相色谱法测定沸程分布.第1部分:中间馏出物和润滑基油 | Petroleum products — Determination of boiling rangedistribution by gas chromatography method — Part 1: Middle distillates and lubricating base oils |
| BS EN 2022-1990 | 带自润滑内衬的耐蚀钢的普通球面轴承规范.轻型系列.尺寸和负荷 | Specification for bearings, spherical plain in corrosion resisting steel with self-lubricating liner - Light series - Dimensions and loads |
| BS EN 2023-1989 | 轴承规范.带自润滑内衬的耐蚀钢普通球面轴承.标准系列.尺寸和负荷 | Specification for bearings - spherical plain in corrosion resisting steel with self-lubricating liner - Normal series - Dimensions and loads |
| BS EN 2064-1992 | 自润滑轴套耐蚀钢球面滑动轴承.技术规范 | Bearings, spherical plain in corrosion resisting steel with self lubricating liner - Technical specification |
| BS EN 2068-1996 | 带自润滑自调心轴承的杆端头.技术规范 | Rod ends with self-lubricating self-aligning bearings - Technical specification |
| BS EN 2264-1996 | 二硫化钼润滑的镀镉合金钢加大承窝安装的双耳浮动自锁托板螺母.等级:900MPa(室温)/235℃ | Nuts, anchor, self-locking, floating, two lug, incremental counterbore, in alloy steel, cadmium plated MoS2 lubricated - Classification: 900 MPa (at ambient temperature) /235 °C |
| BS EN 2285-1990 | 带自润滑内衬的铝合金普通套管规范.尺寸和负荷 | Specification for bushes plain, aluminium alloy with self-lubricating liner - Dimensions and loads |
| BS EN 2286-1990 | 带自润滑内衬的铝合金带法兰缘的套管规范.尺寸和负荷 | Specification for bushes flanged, aluminium alloy with self-lubricating liner - Dimensions and loads |
| BS EN 2287-1990 | 带自润滑内衬的耐蚀钢普通套管规范.尺寸和负荷 | Specification for bushes plain, corrosion resisting steel with self-lubricating liner - Dimensions and loads |
| BS EN 2288-1990 | 带自润滑内衬的耐蚀钢的法兰缘套管规范.尺寸和负荷 | Specification for bushes flanged, corrosion resisting steel with self-lubricating liner - Dimensions and loads |
| BS EN 2311-1990 | 带自润滑内衬的套管规范.技术规范 | Specification for bushes with self-lubricating liner - Technical specification |
| BS EN 2491-1997 | 二硫化钼基干膜润滑油.涂覆法 | Molybdenum disulphide dry lubricants - Coating methods |
| BS EN 2498-1990 | 带自润滑内衬和螺纹柄的可调节的自调心普通轴承的杆形端头规范.尺寸和规范 | Specification for rod ends, adjustable self-aligning plain bearing, with self-lubricating liner and threaded shank - Dimensions and loads |
| BS EN 2501-1992 | 轴承.带自润滑内衬和宽内环的耐蚀钢普通球面轴承.尺寸和负荷 | Bearings, spherical plain in corrosion resisting steel with self-lubricating liner and wide inner ring - Dimensions and loads |
| BS EN 2549-2006 | 航空航天系列.二硫化钼润滑阳极处理的钛制短螺纹紧公差标准螺杆标准六角头螺栓.等级:1100MPa(室温)/315℃ | Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short thread, in titanium, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature) / 315 °C |
| BS EN 2584-2001 | 航空航天系列.具有自润滑轴套的球面耐蚀钢轴承.窄系列.环境温度下的高负荷.尺寸和负荷 | Aerospace series - Bearings, spherical plain in corrosion resisting steel with self-lubricating liner - Narrow series - Elevated load at ambient temperature - Dimensions and loads |
| BS EN 2585-2001 | 航空航天系列.具有自润滑轴套的球面耐蚀钢轴承.宽系列.环境温度下的高负荷.负荷和尺寸 | Aerospace series - Bearings, spherical plain in corrosion-resisting steel with self-lubricating liner - Elevated load at ambient temperature - Dimensions and loads |
| BS EN 2680-2006 | 航空航天系列.MoS2润滑镉镀层铝合金双耳游动自调自锁托板螺母.等级:900MPa(室温)/235℃ | Nuts, anchor, self-locking, floating, self-aligning, two lug, in alloy steel, cadmium plated, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 235 °C |
| BS EN 2753-1996 | 二硫化钼润滑的镀镉合金钢的承窝安装的单耳固定自锁托板螺母.等级:1100MPa(室温)/235℃ | Nuts, anchor, self-locking, fixed, single lug, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated - Classification - 1100 MPa (at ambient temperature) / 235 °C |
| BS EN 2790-1991 | 带自润滑套和啮合量为1.5的螺纹轴的可动调自定位滚动轴承杆端.尺寸和负载 | Rod ends, adjustable, self-aligning plain bearing with self-lubricating liner and threaded shank with engagement: 1.5 thread - Dimensions and loads |
| BS EN 2870-1996 | 二硫化钼润滑的阳极化的钛合金短螺纹紧公差标准螺杆标准双六角头螺栓.等级:1100MPa(室温)/315℃ | Bolts, normal bihexagonal head, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature) /315 °C |
| BS EN 2881-2006 | 航空航天系列.耐蚀钢制钝化MoS2润滑双耳游动沉孔密封耐燃料性自锁托板螺母.等级:900MPa(室温)/120℃ | Nuts, anchor, self-locking, fuel resistant, sealing, floating, two lug, with counterbore, in corrosion resisting steel, passivated, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 120 °C |
| BS EN 2882-2006 | 航空航天系列.MoS2润滑的镉厚板钢制沉头自锁六角螺母和附属垫圈.等级1100 MPa (环境温度)235℃ | Aerospace series - Nuts, hexagonal, self-locking, with counterbore and captive washer, in steel, cadmium plated, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature) / 235℃ |
| BS EN 2884-1996 | 二硫化钼润滑的阳极化钛合金短螺纹大公差标准螺杆斜十字槽盘头螺钉.等级:1100MPa(室温)/315℃ | Screws, pan head, offset cruciform recess, coarse tolerance normal shank, short thread, in titanium alloy, anodized MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3026-1994 | 干膜润滑剂.钢试样的腐蚀试验 | Test method for dry film lubricants - Corrosion test on steel specimens |
| BS EN 3027-1994 | 干膜润滑剂的试验方法.盐雾试验 | Test method for dry film lubricants - Salt spray test |
| BS EN 3030-1994 | 干膜润滑剂试验方法.固体含量测定 | Test method for dry film lubricants - Solids content |
| BS EN 3032-1994 | 干膜润滑剂试验方法.厚度测量 | Test method for dry film lubricants - Thickness measurement |
| BS EN 3037-1997 | 二硫化钼润滑的阳极化的钛合金短螺纹紧公差标准螺杆斜十字槽盘头螺钉.等级:1100 MPa(室温)/315℃ | Screws, pan head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3048-2001 | 有自润滑轴套的防腐钢球面轴承.轻型系列.环境温度下的高负荷.尺寸和负荷 | Bearings, spherical plain in corrosion resisting steel with self-lubricating liner - Light series - Elevated load at ambient temperature - Dimensions and loads |
| BS EN 3304-1997 | 二硫化钼润滑的阳极化的钛合金短螺纹紧公差标准螺杆斜十字槽100°小埋头螺钉.等级:1100 MPa(室温)/315℃ | Screws, 100 ° countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3306-1996 | 二硫化钼润滑的阳极化的钛合金螺纹至螺钉头部的斜十字槽100°标准埋头螺钉.等级:1100 MPa(室温)/315℃ | Screws, 100 ° countersunk normal head, offset cruciform recess, threaded to head, in titanium alloy, anodized, MoS2 lubricated - Classification - 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3307-1997 | 二硫化钼润滑的阳极化的钛合金螺纹至螺钉头部的斜十字槽盘头螺钉.等级:1100 MPa(室温)/315℃ | Screws, pan head, offset cruciform recess, threaded to head, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3308-1996 | 二硫化钼润滑的阳极化的钛合金螺纹至螺钉头部的标准六角头螺钉.等级:1100 MPa(室温)/315℃ | Screws, normal hexagonal head, threaded to head, in titanium alloy, anodized, MoS2 lubricated - Classification - 1100 MPa (at ambient temperature) /315 °C |
| BS EN 3381-1997 | 二硫化钼润滑的阳极的的化钛金属短螺纹紧公差标准螺杆斜十字槽100°标准埋头螺钉.等级:1100 MPa(室温)/315 | Screws, 100 ° countersunk normal head, offset cruciform recess, close tolerance normal shank, short thread, in titanium, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature) /315 °C |
| BS EN 3536-2006 | 航空航天系列.MoS2润滑的耐热钢制自锁紧六角螺母.分类:1100 MPa(环境温度)/315℃ | Aerospace series - Nuts, hexagon, self-locking, in heat resisting steel, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 3740-1997 | 二硫化钼润滑的阳极化的钛合金短螺纹紧公差螺杆薄六角头带肩螺栓.等级:1100 MPa(室温)/315℃ | Bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in titanium alloy, anodized, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C |
| BS EN 377-1993 | 工业过程应用除外的燃气器具及有关控制装置应用的润滑剂 | Lubricants for applications in appliances and associated controls using combustible gases except those designed for use in industrial processes |
| BS EN 4040-2006 | 航空航天.宽内环的带自润滑内衬的耐蚀钢制关节轴承.室温高负荷.尺寸和负荷 | Bearings, spherical plain in corrosion resisting steel with self-lubricating liner with wide inner ring - Elevated loads at ambient temperature - Dimensions and loads |
| BS EN 4591-2005 | 航空航天.耐高温镍基合金钢制MOS2润滑的自调准筒形游动自锁螺母.等级为:1550 MPa (环境温度) / 315 °C | Aerospace series - Nuts, barrel, self-locking, floating, self-aligning,in heat resisting nickel base alloy, MoS2 lubricated - Classification: 15 50 MPa (at ambient temperature) / 315 °C |
| BS EN 50326-2002 | 架空线用导线.润滑脂特性 | Conductors for overhead lines - Characteristics of greases |
| BS EN 61221-2004 | 石油产品及润滑剂.三芳基磷酸酯涡轮机控制液(ISO-L-TCD类).规范 | Petroleum products and lubricants - Triaryl phosphate ester turbine control fluids (category ISO-L-TCD) - Specifications |
| BS EN ISO 10438-1-2003 | 石油、石化和天然气工业.润滑、油封、控油系统和辅助装置.一般要求 | Petroleum, petrochemical and natural gas industries - Lubrication , shaft-sealing and control-oil systems and auxiliaries - General requirements |
| BS EN ISO 10438-2-2003 | 石油和天然气工业.润滑、油封、控油系统和辅助装置.专用油系统 | Petroleum and natural gas industries - Lubrication, shaft sealing and control oil systems and auxiliaries - Special purpose oil systems |
| BS EN ISO 10438-3-2003 | 石油、石化和天然气工业.润滑、油封、控油系统和辅助装置.通用油系统 | Petroleum, petrochemical and natural gas industries - Lubrication , shaft sealing and control oil systems and auxilliaries - General-purpose oil systems |
| BS EN ISO 10438-4-2004 | 石油、石化和天然气工业.润滑、油封、控油系统和辅助装置.自动气封支撑系统 | Petroleum, petrochemical and natural gas industries - Lubrication , shaft-sealing and control-oil systems and auxiliaries - Self-acting gas seal support systems |
| BS EN ISO 12156-1-2006 | 柴油.用高频往复装置(HFRR)进行润滑性能评定.试验方法 | Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Test method |
| BS EN ISO 12922-1999 | 润滑油、工业油及有关产品(L级).H族(液压系统).HFAE、HFAS、HFB、HFC、HFDR和HFDU类别规范 | Lubricants, industrial oils and related products (class L) - Family H (hydraulic systems) - Specifications for categories HFAE, HFAS, HFB, HFC, HFDR and HFDU |
| BS EN ISO 13944-2006 | 含润滑剂的金属粉末混合物.润滑剂含量测定.索格利特萃取法 | Lubricated metal-powder mixes - Determination of lubricant content - Modified Soxhlet extraction method |
| BS EN ISO 21469-2006 | 机械安全.附带产品接触的润滑剂.卫生要求 | Safety of machinery - Lubricants with incidental product contact - Hygiene requirements |
| BS EN ISO 6743-4-1999 | 润滑剂、工业用润滑油和有关产品(L类).分类.H族(液压系统) | Lubricants, industrial oils and related products (class L) - Classification - Family H (hydraulic systems) |
| BS ISO 10792-1-1996 | 航空和航天.带自润滑衬瓦的耐腐蚀钢机体球面滑动轴承.公制系列 | Aerospace - Airframe spherical plain bearings in corrosion-resisting steel with self-lubricating liner - Metric series |
| BS ISO 10792-2-1996 | 航空和航天.带自润滑衬瓦的耐腐蚀钢机体球面滑动轴承.英制系列 | Aerospace - Airframe spherical plain bearings in corrosion-resisting steel with self-lubricating liner - Inch series |
| BS ISO 10792-3-1996 | 航空和航天.带自润滑衬瓦的耐腐蚀钢机体球面滑动轴承.技术规范 | Aerospace - Airframe spherical plain bearings in corrosion-resisting steel with self-lubricating liner - Technical specification |
| BS ISO 11158-1998 | 润滑剂、工业油和相关产品(L类).H系列(液压系统).HH、HL、HM、HR、HV和HG类别规范 | Lubricants, industrial oils and related products (class L) - Family H (hydraulic systems) - Specifications for categories HH, HL, HM, HR, HV and HG |
| BS ISO 12128-2002 | 滑动轴承.润滑油孔、油槽和油穴.尺寸、类型、标记及其对轴套的应用 | Plain bearings - Lubrication holes, grooves and pockets - Dimensions, types, designation and their application to bearing bushes |
| BS ISO 12156-2-2007 | 柴油.用高频往复装置(HFRR)进行润滑油评定.极限值 | Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Limit |
| BS ISO 12922-1999 | 润滑油,工业油和相关产品(L级).H族(液压系统).HFA、HFAS、HFB、HFC、HFDR和HFDU类别规范 | Lubricants, industrial oils and related products (class L) - Family H (hydraulic systems) - Specifications for categories HFAE, HFAS, HFB, HFC, HFDR and HFDU |
| BS ISO 12925-1-1998 | 润滑剂、工业用油及相关产品(L类).C系列(齿轮).第1部分:密封式齿轮系统用润滑剂规范 | Lubricants, industrial oils and related products (class L) - Family C (Gears) - Specifications for lubricants for enclosed gear systems |
| BS ISO 13357-1-2002 | 石油产品.润滑油可过滤性测定.含水油过滤的程序 | Petroleum products - Determination of the filterability of lubricating oils - Procedure for oils in the presence of water |
| BS ISO 13357-2-2005 | 石油产品.润滑油可过滤性测定.干油程序 | Petroleum products - Determination of the filterability of lubricating oils - Procedure for dry oils |
| BS ISO 13737-2004 | 石油及其制品的试验方法.BS 2000-527:石油制品及润滑剂.润滑脂低温针入度的测定 | Method of test for petroleum and its products - BS 2000-527: Petroleum products and lubricants - Determination of low-temperature cone penetration of lubricating greases |
| BS ISO 13738-2000 | 润滑剂、工业用油和有关制品(L类).E系列(内燃机油).两冲程汽油发动机油(类别EGB、EGC和EGD) 规范 | Lubricants, industrial oils and related products (class L) - Family E (internal combustion engine oils) - Specifications for two-stroke-cycle gasoline engine oils (categories EGB, EGC and EGD) |
| BS ISO 14635-3-2006 | 齿轮.FZG试验规程.有关半流质齿轮润滑油的刮磨承载能力和磨损特性的FZG试验方法A/2、8/50 | Gears - FZG test procedures - FZG test method A/2, 8/50 for relative scuffing load-carrying capacity and wear characteristics of semifluid gear greases |
| BS ISO 15380-2002 | 润滑剂、工业用油和相关产品(L类).H族(液压系统).HETG, HEPG, HEES 和 HEPR类的规范 | Lubricants, industrial oils and related products (class L) - Family H (hydraulic systems) - Specifications for categories HETG, HEPG, HEES and HEPR |
| BS ISO 18904-2000 | 成像材料.冲洗过的胶片.测定润滑方法 | Imaging materials - Processed films - Method for determining lubrication |
| BS ISO 19378-2003 | 润滑剂、工业用油和相关产品(L级).机床润滑剂.种类和规范 | Lubricants, industrial oils and related products (class L) - Machine-tool lubricants - Categories and specifications |
| BS ISO 3046-1-2002 | 往复式内燃机.性能.功率、燃料消耗量和润滑油消耗量和试验方法说明.通用内燃机的附加要求 | Reciprocating internal combustion engines - Performance - Declarations of power, fuel and lubricating oil consumptions, and test methods - Additional requirements for engines for general use |
| BS ISO 3547-3-2006 | 滑动轴承.卷制轴套.润滑油孔、油槽和油穴 | Plain bearings - Wrapped bushes - Lubrication holes, grooves and indentations |
| BS ISO 6301-1-1998 | 气动流体动力.压缩空气润滑器.供货商的文件和产品标志要求包括主要特性 | Pneumatic fluid power - Compressed air lubricators - Main characteristics to be included in supplier's literature and product-marking requirements |
| BS ISO 6301-2-1998 | 气动流体动力.压缩空气润滑器.供货商文件包括主要特性测定的试验方法 | Pneumatic fluid power - Compressed air lubricators - Test methods to determine the main characteristics to be included in supplier's literature |
| BS ISO 6415-2005 | 内燃机.润滑油用旋压式过滤器.尺寸 | Internal combustion engines - Spin-on filters for lubricating oil - Dimensions |
| BS ISO 6743-1-2002 | 润滑剂、工业用润滑油和有关产品(L类).分类.A 族(总损耗系统) | Lubricants, industrial oils and related products (class L) - Classification - Family A (Total loss systems) |
| BS ISO 6743-3-2004 | 润滑剂、工业润滑油和有关产品(L类).分类.D组(压缩机) | Lubricants, industrial oils and related products (class L) - Classification - Family D (Compressors) |
| BS ISO 6743-4-1999 | 润滑剂、工业用润滑油和有关产品(L类).分类.第4部分:H族(液压系统) | Lubricants, industrial oils and related products (class L) - Classification - Family H (hydraulic systems) |
| BS ISO 6743-5-2006 | 润滑剂、工业润滑油和相关产品(L类).分类.T族(涡轮机) | Lubricants, industrial oils and related products (class L) - Classification - Family T (turbines) |
| BS ISO 6743-9-2004 | 润滑剂、工业润滑油和有关产品(L类).分类.X族(润滑脂) | Lubricants, industrial oils and related products (class L) - Classification - Family X (Greases) |
| BS ISO 6743-99-2002 | 润滑剂、工业用润滑油和有关产品(L类).分类.总则 | Lubricants, industrial oils and related products (class L) - Classification - General |
| BS ISO 7967-6-2005 | 往复式内燃机.零部件和系统词汇.润滑系统 | Reciprocating internal combustion engines - Vocabulary of components and systems - Lubricating systems |
| BS ISO 8068-2006 | 润滑剂、工业润滑油和相关产品(L类)T族(涡轮).涡轮机用润滑油规范 | Lubricants, industrial oils and related products (class L) - Family T (turbines) - Specification for lubricating oils for turbines |
| BS ISO/TS 12927-2000 | 润滑剂、工业油和相关产品(L级).M系列(金属加工).制定规范的指南 | Lubricants, industrial oils and related products (class L) - Family M (metalworking) - Guidelines for establishing specifications |
| BS ISO/TS 12928-2000 | 润滑剂、工业油料和相关产品(L级).R系列(临时防腐产品).制定规范的导则 | Lubricants, industrial oils and related products (class L) - Family R (products for temporary protection against corrosion) - Guidelines for establishing specifications |
| BS SP 115 to 117-1956 | 航空用液压表面止动型润滑脂嘴规范 | Specifications for hydraulic surface-check type lubricating nipples for aircraft |
| BS SP 21-1950 | 航空用润滑脂嘴规范 | Specification for lubricating nipples for aircraft purposes |
| PD CR 13767-2001 | 污物特性.含有和/或不含润滑脂和筛屑的污物焚烧实施规程 | Characterization of sludges. Good practice for sludges incineration with and without grease and screenings |
| PD IEC 61394-2001 | 架空线.铝、铝合金和钢裸导线用润滑脂的特性 | Overhead lines. Characteristics of greases for aluminium, aluminium alloy and steel bare conductors |
| 编号 | 中文名称 | 英文名称 |