| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| BS 1133-21-1991 | 包装规程.第21节:再生纤维素薄膜,塑料薄膜,铝箔,挠性多层板和金属化材料 | Packaging code - Regenerated cellulose film, films made of plastics, aluminium foil, flexible multilayer structures and metallized materials |
| BS 1133-22-1989 | 包装规程.第22节:塑料容器包装 | Packaging code - Packaging in plastics containers |
| BS 1203-2001 | 热固酚醛和氨基塑料木材胶粘剂.分类和试验方法 | Hot-setting phenolic and aminoplastic wood adhesives - Classification and test method |
| BS 1212-3-1990 | 浮子阀.第3部分:仅供冷水用隔膜型塑料体浮子操作阀(不包括浮子) | Float operated valves - Specification for diaphragm type float operated valves (plastics bodied) for cold water services only (excluding floats) |
| BS 1254-1981 | 塑料马桶座规格 | Specification for WC seats (plastics) |
| BS 1322-1992 | 氨基塑料模塑材料规范 | Specification for aminoplastic moulding materials |
| BS 1679-8-1992 | 药剂容器.固体剂型、半固体型和粉末状药剂用玻璃和塑料容器规范 | Containers for pharmaceutical dispensing - Specification for glass and plastics containers for solid dosage forms, semi-solids and powders |
| BS 2456-1990 | 冷水设备用浮子操作阀的浮子(塑料制品)规范 | Specification for floats (plastics) for float operated valves for cold water services |
| BS 2782-0-2004 | 塑料的试验方法.引言 | Methods of testing - Plastics - Introduction |
| BS 2782-1 Method 130A-1991 | 塑料试验方法.第1部分:热性能.试验方法130A:刚果红法测定聚氯乙烯热稳定性 | Methods of testing plastics - Thermal properties - Determination of the thermal stability of polyvinyl chloride by the Congo red method |
| BS 2782-1 Method 131B-1983 | 塑料试验方法.热性能.挠性聚氯乙烯板材加热老化延伸性测定 | Methods of testing plastics - Thermal properties - Determination of extensibility after heat ageing of flexible polyvinyl chloride sheet |
| BS 2782-1 Method 140A-1992 | 塑料试验方法.第1部分:热特性.方法140A:卧式和立式样品小火源燃烧性能测定 | Methods of testing plastics - Thermal properties - Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
| BS 2782-1 Method 140D-1997 | 塑料试验方法.第1部分:热性能.试验方法140D:550mm×35mm聚氯乙烯薄膜试片易燃性(实验室法) | Methods of testing plastics - Thermal properties - Flammability of a test piece 550 mm x 35 mm of thin polyvinyl chloride sheeting (laboratory method) |
| BS 2782-1 Method 140E-1982 | 塑料试验方法.热性能.小型倾钭试片置于酒精火焰上的可燃性(实验室法) | Methods of testing plastics - Thermal properties - Flammability of a small, inclined test piece exposed to an alcohol flame (laboratory method) |
| BS 2782-1 Method 150C-1983 | 塑料试验方法.第1部分:热性能.试验方法150C:挠性聚氯乙烯板低温延伸率测定 | Methods of testing plastics - Thermal properties - Determination of low temperature extensibility of flexible polyvinyl chloride sheet |
| BS 2782-1 Method 150D-1976 | 塑料试验方法.第1部分:热性能.试验方法150D:薄膜与薄片冷裂温度 | Methods of testing plastics - Thermal properties - Cold crack temperature of film and thin sheeting |
| BS 2782-1 Method 151A-1984 | 塑料试验方法.第1部分:热性能.挠性聚氯乙烯挤压混合物冷弯温度测定 | Methods of testing plastics - Thermal properties - Determination of cold bend temperature of flexible polyvinyl chloride extrusion compound |
| BS 2782-1 Method 153A-1991 | 塑料试验方法.第1部分:热性能.方法153A:挠性材料抗扭刚度测定(通用方法) | Methods of testing plastics - Thermal properties - Determination of stiffness in torsion of flexible materials (general method) |
| BS 2782-1 Method 153B-1991 | 塑料试验方法.第1部分:热性能.方法153B:挠性材料抗扭刚度测定(氯乙烯混合物法) | Methods of testing plastics - Thermal properties - Determination of stiffness in torsion of flexible materials (method for vinyl chloride compounds) |
| BS 2782-1 Methods 131C and 131D-1978 | 塑料的试验方法.热性能.热固模制材料加热后的抗碎强度(耐热性).热固层叠板材或模制材料加热后的抗碎强度 ( | Methods of testing plastics - Thermal properties - Crushing strength after heating (heat resistance) of thermosetting moulding material - Crushing strength after heating (heat resistance) of thermosetting laminated sheet or mouldings |
| BS 2782-1 Methods 134A and 134B-1992 | 塑料试验方法.第1部分:热性能.方法134A:热塑塑料氧化感应时间测定 | Methods of testing plastics - Thermal properties - Determination of the oxidation induction time of thermoplastics |
| BS 2782-10 Method 1001-1977 | 塑料试验方法.第10部分:玻璃纤维增强塑料.试验方法1001:用巴科尔硬度计测量硬度 | Methods of testing plastics - Glass reinforced plastics - Measurement of hardness by means of a Barcol impressor |
| BS 2782-10 Method 1002-1977 | 塑料试验方法.第10部分:玻璃纤维增强塑料.试验方法1002:灼烧重量损失测定 | Methods of testing plastics - Glass reinforced plastics - Determination of loss on ignition |
| BS 2782-10 Method 1003-1977 | 塑料试验方法.第10部分:玻璃纤维增强塑料.试验方法1003:拉伸性能测定 | Methods of testing plastics - Glass reinforced plastics - Determination of tensile properties |
| BS 2782-10 Method 1004-1977 | 塑料试验方法.第10部分:玻璃纤维增强塑料.试验方法1004:调节和试验用标准大气压 | Methods of testing plastics - Glass reinforced plastics - Standard atmospheres for conditioning and testing |
| BS 2782-10 Method 1005-1977 | 塑料的试验方法.第10部分:玻璃纤维增强塑料.试验方法1005:挠曲特性测定.三点法 | Methods of testing plastics - Glass reinforced plastics - Determination of flexural properties - Three point method |
| BS 2782-10 Method 1006-1978 | 塑料试验方法.第10部分:玻璃纤维增强塑料.试验方法1006:合成树脂浸渍玻璃纤维织物中挥发物和树脂含量测定 | Methods of testing plastics - Glass reinforced plastics - Determination of volatile matter and resin content of synthetic resin-impregnated textile glass fabric |
| BS 2782-11 Method 1108A-1989 | 塑料试验方法.第11部分:热塑性塑料管、接头和阀门.试验方法1108A:管界面限定碰撞率 | Methods of testing plastics - Thermoplastics pipes, fittings and valves - True impact rate (TIR) boundaries of pipes |
| BS 2782-11 Method 1109A-1989 | 塑料试验方法.第11部分:热塑性塑料、接头和阀门.试验方法1109A:非承压聚乙烯管和接头耐坏境应力开裂性 | Methods of testing plastics - Thermoplastics pipes, fittings and valves - Resistance to environmental stress cracking of polyethylene pipes and fittings for non-pressure applications |
| BS 2782-11 Method 1112A-1989 | 塑料的试验方法.第11部分:热塑性塑料管,配件和阀门.试验方法1112A:非承压用热塑性塑料管及其配件的不密封性 | Methods of testing plastics. Thermoplastics pipes, fittings and valves. Leaktightness of thermoplastics pipes and fittings for non-pressure applications |
| BS 2782-11 Method 1121B-1997 | 塑料的试验方法.第11部分:热塑管、接头和阀门.流体输送用热塑管.试验方法1121B:额定外部直径和额定压力.米 | Methods of testing plastics - Thermoplastics pipes, fittings and valves - Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Metric series |
| BS 2782-11 Method 1121C-1997 | 塑料试验方法.第11部分:热塑管、接头和阀门.流体输送用热塑管.试验方法1121C:额定外部直径和额定压力.英尺 | Methods of testing plastics - Thermoplastics pipes, fittings and valves - Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Inch-based series |
| BS 2782-11 Method 1121H-1996 | 塑料试验方法.第11部分:热塑性塑料管、接头和阀门.试验方法1121H:非承压液体输送热塑性塑料管.管头损失计算 | Methods of testing plastics - Thermoplastics pipes, fittings and valves - Thermoplastics pipes for the transport of liquids under pressure - Calculation of head losses |
| BS 2782-2 Method 241A-1984 | 塑料试验方法.第2部分 :电气性能.方法241A聚氯乙烯混合物对聚乙烯损耗角正切向影响测定 | Methods of testing plastics - Electrical properties - Determination of effect of polyvinyl chloride compound on the loss tangent of polyethylene |
| BS 2782-3 Method 323B-1996 | 塑料试验方法.机械性能.弯曲振动.非共振法 | Methods of testing plastics - Mechanical properties - Flexural vibration - Non-resonance method |
| BS 2782-3 Method 323C-1996 | 塑料试验方法..第3部分:机械特性.试验方法323C:剪切振动.非共振法 | Methods of testing plastics - Mechanical properties - Shear vibration - Non-resonance method |
| BS 2782-3 Method 323D-1996 | 塑料试验方法.机械特性.扭转振动.非共振法 | Methods of testing plastics - Mechanical properties - Torsional vibration - Non-resonance method |
| BS 2782-3 Method 323E-1997 | 塑料试验方法.第3部分:机械性能.径向剪切震动.试验方法323E:波传播法 | Methods of testing plastics - Mechanical properties - Longitudinal and shear vibration - Wave-propagation method |
| BS 2782-3 Method 327A-1993 | 塑料试验方法.第3部分:机械性能.方法327A:聚四氟乙烯制品抗拉强度与断裂伸长率测定 | Methods of testing plastics - Mechanical properties - Determination of tensile strength and elongation at break of polytetrafluoroethylene (PTFE) products |
| BS 2782-3 Method 332A-1976 | 塑料试验方法.第3部分:机械性能.试验方法332A:塑料薄膜韧性 | Methods of testing plastics - Mechanical properties - Stiffness of plastics film |
| BS 2782-3 Method 341A-1977 | 塑料试验方法.第3部分:机械性能.试验方法341A:增强塑料表观层间剪切强度测定 | Methods of testing plastics - Mechanical properties - Determination of apparent interlaminar shear strength of reinforced plastics |
| BS 2782-3 Method 352F-1996 | 塑料试验方法.第3部分:机械特性.试验方法352F:自由落体法测定抗冲击(仪器穿孔试验) | Methods of testing plastics - Mechanical properties - Determination of impact resistance by the free-falling dart method (instrumented puncture test) |
| BS 2782-3 Method 360C-1991 | 塑料试验方法.第3部分:机械性能.方法360C.引发法测定塑料薄膜和塑料片抗撕裂性能 | Methods of testing plastics - Mechanical properties - Determination of tear resistance of plastics film and sheeting by the initiation method |
| BS 2782-3 Method 370-1996 | 塑料试验方法.第3部分:机械性能.试验方法370:砂轮测定耐磨性 | Methods of testing plastics - Mechanical properties - Determination of resistance to wear by abrasive wheels |
| BS 2782-3 Methods 320A to 320F-1976 | 塑料的试验方法.第3部分:机械性能.试验方法320A-320F:抗拉强度、伸长值和弹性模量 | Methods of testing plastics - Mechanical properties - Tensile strength, elongation and elastic modulus |
| BS 2782-4 Method 432A-1991 | 塑料试验方法.第4部分:化学性能.试验方法432A:不饱和聚酯树脂基增强塑料残余苯乙烯单体含量测定 | Methods of testing plastics - Chemical properties - Determination of residual styrene monomer content in reinforced plastics based on unsaturated polyester resins |
| BS 2782-4 Method 432D-1995 | 塑料试验方法.第4部分:化学性能.试验方法432D:不饱和聚酯树脂蒸发苯值测定 | Methods of testing plastics - Chemical properties - Determination of styrene evaporation from unsaturated polyester resins |
| BS 2782-4 Method 433A-1979 | 塑料试验方法.第4部分:化学性能.试验方法433A:环氧树脂与缩水甘油脂无机氯测定 | Methods of testing plastics - Chemical properties - Determination of inorganic chlorine in epoxide resins and glycidyl esters |
| BS 2782-4 Method 434B-1977 | 塑料试验方法.第4部分:化学性能.试验方法434B:用氯仿萃取物紫外线吸收法测定聚烯烃混合料抗氧化剂 | Methods of testing plastics - Chemical properties - Determination of antioxidants in polyolefin compounds by ultra-violet absorption of the chloroform extract |
| BS 2782-4 Method 434D-1975 | 塑料试验方法.第4部分:化学性能.试验方法434D:用分光光度法测定聚烯烃混合料抗氧化剂 | Methods of testing plastics - Chemical properties - Determination of antioxidants in polyolefin compounds by a spectrophotometric method |
| BS 2782-4 Method 451A-1978 | 塑料试验方法.第4部分:化学性能.酚醛模制件的丙酮可溶物的测定 | Methods of testing plastics - Chemical properties - Determination of acetone-soluble matter in phenolic mouldings |
| BS 2782-4 Method 451B-1978 | 塑料的试验方法.化学性能.酚醛模制材料在模制后丙酮可溶物的测定 | Methods of testing plastics - Chemical properties - Determination of acetone-soluble matter in phenolic moulding materials after moulding |
| BS 2782-4 Method 452B-1993 | 塑料测试方法.第4部分:化学特性.聚烯烃化合物中炭黑含量测定 | Methods of testing plastics - Chemical properties - Determination of carbon black content of polyolefin compound |
| BS 2782-4 Method 452C-1979 | 塑料的试验方法.化学性能.低密度聚乙烯化合物中丁基橡胶含量的测定 | Methods of testing plastics - Chemical properties - Determination of butyl rubber content of low density polyethylene compounds |
| BS 2782-4 Method 453C-1996 | 塑料试验方法.第4部分:化学性能.试验方法453C:用气相色谱法测定苯乙烯/丙烯腈共聚物中残余丙烯腈单体含量 | Methods of testing plastics - Chemical properties - Determination of residual acrylonitrile monomer content in styrene/acrylonitrile copolymers using gas chromatography |
| BS 2782-4 Method 454G-1996 | 塑料试验方法.第4部分:化学特性.方法454G:高聚物分散法.筛分余值测定(大颗粒和凝固物含量) | Methods of testing plastics - Chemical properties - Polymer dispersions - Determination of sieve residue (gross particle and coagulum content) |
| BS 2782-4 Method 470B-1999 | 塑料试验方法.化学性能.聚对苯二甲酸乙酯灰分的测定 | Methods of testing plastics - Chemical properties - Determination of ash of polyalkylene terephthalates |
| BS 2782-4 Method 470C-1991 | 塑料试验方法.第4部分:化学性能.试验方法470C:未增塑醋酸纤维素灰分测定 | Methods of testing plastics - Chemical properties - Determination of ash of unplasticized cellulose acetate |
| BS 2782-4 Methods 451F to 451J-1978 | 塑料试验方法.第4部分:化学性能.酚醛模制材料甲醛含量测定(比色法).酚醛模制材料甲醛含量测定(重量法).酚醛 | Methods of testing plastics - Chemical properties - Determination of formaldehyde in phenolic mouldings (colorimetric method) - Determination of formaldehyde in phenolic mouldings (gravimetric method) - Determination of sulphates in phenolic mouldings - Determination of chlorides in phenolic mouldings |
| BS 2782-4 Methods 452D to 452F-1978 | 塑料试验方法.第4部分:化学性能.聚烯烃混合物水萃取物pH值测定.聚烯烃混合物水可溶硫酸盐含量测定.聚烯烃混 | Methods of testing plastics - Chemical properties - Determination of pH of water extract of polyolefin compound - Determination of water-soluble sulphates in polyolefin compound - Determination of water-soluble chlorides in polyolefin compound |
| BS 2782-5 Method 520A-1992 | 塑料试验方法.第5部分:.风化条件下光学性能和颜色性能.方法520A:镜面光泽度测定 | Methods of testing plastics - Optical and colour properties, weathering - Determination of specular gloss |
| BS 2782-5 Method 521A-1992 | 塑料的试验方法.第5部分:风化条件下光学性能和颜色性能.方法521A:塑料薄膜和薄板霾度的测定 | Methods of testing plastics - Optical and colour properties, weathering - Determination of haze of film and sheet |
| BS 2782-5 Method 540B-1982 | 塑料的试验方法.风化条件下光学性能和颜色性能.实验室光源辐照方法,(氙弧灯、密封碳弧灯、敞口火焰碳弧灯、 | Methods of testing plastics - Optical and colour properties, weathering - Methods of exposure to laboratory light sources, (xenon arc lamp, enclosed carbon arc lamp, open-flame carbon arc lamp, fluorescent tube lamps) |
| BS 2782-5 Method 540C-1988 | 塑料试验方法.第5部分:风化条件下光学和颜色性能.试验方法540C:用聚砜胶片测定紫外线辐射强度 | Methods of testing plastics - Optical and colour properties, weathering - Determination of ultraviolet radiation intensity using polysulphone film |
| BS 2782-5 Method 540G-1995 | 塑料试验方法.第5部分:风化条件下光学和颜色特性.方法540G:实验室灯光曝露法.有焰碳弧灯源 | Methods of testing plastics - Optical and colour properties, weathering - Methods of exposure to laboratory light sources - Open flame carbon-arc lamps |
| BS 2782-5 Method 552A-1999 | 塑料试验方法.风化后光学和颜色特性.在透过玻璃的日光、自然风化和试验室光源下暴露后颜色和特性变化的测定 | Methods of testing plastics - Optical and colour properties, weathering - Determination of changes in colour and variations in properties after exposure to daylight under glass, natural weathering or laboratory light sources |
| BS 2782-5 Methods 530A and 530B-1976 | 塑料的试验方法.风化下光学和颜色性能.黄色指数测定.近似白色或近似无色材料的测定 | Methods of testing plastics - Optical and colour properties, weathering - Determination of yellowness index - Determination of the colour of near-white or near-colourless materials |
| BS 2782-6 Method 621C-1983 | 塑料试验方法.第6部分:尺寸特性.模制材料体积系数测定 | Methods of testing plastics - Dimensional properties - Determination of the bulk factor of moulding materials |
| BS 2782-6 Method 621D-1978 | 塑料试验方法.第6部分:尺寸特性.聚氯乙烯树脂压实表观体积密度测定 | Methods of testing plastics - Dimensional properties - Determination of compacted apparent bulk density of PVC resins |
| BS 2782-6 Method 630A-1994 | 塑料试验方法.第6部分:尺寸特性.用机械扫描法测定挠性片厚度 | Methods of testing plastics - Dimensional properties - Determination of thickness by mechanical scanning of flexible sheet |
| BS 2782-6 Method 631A-1993 | 塑料的试验方法.第6部分:尺寸特性.柔性板材重量厚度分析和屈服性测定 | Methods of testing plastics - Dimensional properties - Determination of gravimetric thickness and yield of flexible sheet |
| BS 2782-6 Method 632A-1993 | 塑料试验方法.第6部分:尺寸特性.柔性板材长度和宽度测定 | Methods of testing plastics - Dimensional properties - Determination of length and width of flexible sheet |
| BS 2782-6 Method 640A-1979 | 塑料的试验方法.尺寸特性.热固性模制材料在压模制棒材过程中试样的收缩量测定 | Methods of testing plastics - Dimensional properties - Determination of shrinkage of test specimens in the form of bars of compression moulded thermosetting moulding materials |
| BS 2782-6 Method 641A-1983 | 塑料试验方法.第6部分:尺寸特性.100℃时挠性聚氯乙烯薄板尺寸稳定性测定 | Methods of testing plastics - Dimensional properties - Determination of dimensional stability at 100 °C of flexible polyvinyl chloride sheet |
| BS 2782-6 Method 643A-1976 | 塑料的试验方法.第6部分:尺寸特性.试验方法643A:收缩包装用薄膜热缩变 | Methods of testing plastics - Dimensional properties - Shrinkage on heating of film intended for shrink wrapping applications |
| BS 2782-6 Methods 620A to 620D-1991 | 塑料的试验方法.尺寸特性.非泡沫塑料的密度和相对密度的测定 | Methods of testing plastics - Dimensional properties - Determination of density and relative density of non-cellular plastics - Methods 620A to 620D:Determination of density and relative density of non-cellular plastics |
| BS 2782-7 Method 720B-1979 | 塑料试验方法.第7部分:流变性能.试验方法720B:苯酚与醇酸模制材料的杯模流动溢法流动性 | Methods of testing plastics - Rheological properties - Cup flow of phenolic and alkyd moulding materials |
| BS 2782-7 Method 721A-1988 | 塑料试验方法. 第7部分:流变性能.试验方法721A:树脂浸渍玻璃纤维测定树脂流失量 | Methods of testing plastics - Rheological properties - Determination of resin flow from resin impregnated glass fabric |
| BS 2782-7 Method 732D-1999 | 测试塑料的方法.流变特性.用毛细管粘度计测定稀释溶液中聚碳酸酯(PC)模塑和挤压材料的粘度 | Methods of testing plastics - Rheological properties - Determination of the viscosity of polycarbonate (PC) moulding and extrusion materials in dilute solution using capillary viscometers - Method 732D: Determination of the viscosity of polycarbonate (PC) moulding and extrusion materials in dilute solution using capillary viscometers |
| BS 2782-7 Method 732F-1991 | 塑料试验方法.第7部分:流变性能.试验方法732F:异丁烯酸甲酯聚合物粘度值测定 | Methods of testing plastics - Rheological properties - Determination of viscosity number of methyl methacrylate polymers |
| BS 2782-7 Method 740B-1996 | 塑料试验方法.第7部分:变流性能.方法740B:聚合物悬浮液和合成橡胶乳液.冻结-溶化循环稳定性试验 | Methods of testing plastics - Rheological properties - Polymer dispersions and synthetic rubber latices - Freeze-thaw cycle stability test |
| BS 2782-7 Method 740C-1996 | 塑料试验方法.第7部分:变流性能.方法740C:聚合物悬浮液.白点温度和最快薄膜形成温度的测定 | Methods of testing plastics - Rheological properties - Polymer dispersions - Determination of white point temperature and minimum film-forming temperature |
| BS 2782-8 Method 820A-1996 | 塑料试验方法.第8部分:其他性能.方法820A:水蒸气透过率的测定(盘测法) | Methods of testing plastics - Other properties - Determination of water vapour transmission rate (dish method) |
| BS 2782-8 Method 822A-1992 | 塑料试验方法.第8部分:其他性能.方法822A:塑料薄膜水蒸汽传播速度测定 | Methods of testing plastics - Other properties - Determination of water vapour transmission rate of plastics films (sachet method) |
| BS 2782-8 Method 826A-1992 | 塑料试验方法.第8部分:其它性能.方法826A:塑料片印痕附着力测定 | Methods of testing plastics - Other properties - Determination of adhesion of print on plastics sheet |
| BS 2782-8 Method 835A-1980 | 塑料的试验方法.其他特性.酚醛树脂胶凝时间的测定 | Methods of testing plastics - Other properties - Determination of gelation time of phenolic resins |
| BS 2782-8 Method 835B-1980 | 塑料的试验方法.其他特性.聚酯树脂胶凝时间的测定(手工方法) | Methods of testing plastics - Other properties - Determination of gelation time of polyester resins (manual method) |
| BS 2782-8 Method 835D-1980 | 塑料试验方法.第8部分:其他性能.试验方法835D:用热板测定热固性树脂胶凝时间 | Methods of testing plastics - Other properties - Determination of gelation time of thermosetting resins using a hot plate |
| BS 2782-8 Methods 823A and 823B-1978 | 塑料试验方法.第8部分:其他性能.试验方法823A和823B:使用显微镜评定聚乙烯中碳黑分散 | Methods of testing plastics - Other properties - Methods for the assessment of carbon black dispersion in polyethylene using a microscope |
| BS 2782-9 Method 940A-1990 | 塑料试验方法. 第9部分:取样和试样制备.试验方法940A:具有规定回缩率的未定形热塑塑料棒材试样制备 | Methods of testing plastics - Sampling and test specimen preparation - Preparation of test specimens of amorphous thermoplastics in the form of bars with a specified reversion |
| BS 2782-9 Method 940B-1989 | 塑料试验方法. 第9部分:取样和试件制备.试验方法940B:用注塑矩形板制备具有规定回缩率的无定形热塑性试件 | Methods of testing plastics - Sampling and test specimen preparation - Preparation of test specimens of amorphous thermoplastics with a specified reversion by injection moulding rectangular plates |
| BS 3130-5-1994 | 包装术语.第5部分:塑料和软包装(不包括纸包装) | Glossary of packaging terms - Plastics and flexible packaging (excluding paper) |
| BS 3221-6-1987 | 药用量具.第6部分:5ml药用立式塑料量匙规范 | Medicine measures - Specification for free-standing plastics medicine measuring spoons of 5 mL capacity |
| BS 3396-1-1991 | 塑料增强用的机织玻璃纤维织物.第1部分:坯布规范 | Woven glass fibre fabrics for plastics reinforcement - Specification for loom-state fabrics |
| BS 3396-2-1987 | 塑料增强用机织玻璃纤维织物.第2部分:退浆织物规范 | Woven glass fibre fabrics for plastics reinforcement - Specification for desized fabrics |
| BS 3396-3-1987 | 塑料增强用机织玻璃纤维织物.第3部分:聚酯树脂系统用成品布规范 | Woven glass fibre fabrics for plastics reinforcement - Specification for finished fabrics for use with polyester resin systems |
| BS 3502-3-1993 | 塑料和橡胶材料符号.第3部分:配料成分符号一览表 | Symbols for plastics and rubber materials - Schedule for symbols for compounding ingredients |
| BS 3735-1987 | 塑料和橡胶吸尘箱盖规范 | Specification for plastics and rubber dustbin lids |
| BS 4154-1-1985 | 热固性聚酯树脂半透明玻璃纤维增强塑料波纹板.第1部分:材料和性能要求规范 | Corrugated plastics translucent sheets made from thermo-setting polyester resin (glass fibre reinforced) - Specification for material and performance requirements |
| BS 4154-2-1985 | 热固性聚酯树脂半透明玻璃纤维增强塑料波纹板.第2部分:外形和尺寸规范 | Corrugated plastics translucent sheets made from thermo-setting polyester resin (glass fibre reinforced) - Specification for profiles and dimensions |
| BS 4480-2-1974 | 滑动轴承规范.米制系列.第2部分:整体塑料轴套 | Specification for plain bearings: metric series - Solid plastics bushes |
| BS 4549-1-1997 | 增强塑料模塑件质量控制要求槽则.第1部分:玻璃纤维增强聚酯树脂模塑件质量控制方案制定指南 | Guide to quality control requirements for reinforced plastics mouldings - Guide to the preparation of a scheme to control the quality of glass reinforced polyester mouldings |
| BS 4592-4-2006 | 工业用地面和梯板.玻璃增强塑料(GRP)敞口条形栅栏.规范 | Industrial type flooring and stair treads - Glass reinforced plastics (GRP) open bar gratings - Specification |
| BS 4592-5-2006 | 工业用地面和梯板.金属和玻璃增强塑料(GRP)中固体板.规范 | Industrial type flooring and stair treads - Solid plates in metal and glass reinforced plastics (GRP) - Specification |
| BS 4592-6-2008 | 工业地板和梯板.玻璃增强塑料(GRP)注模开口网状栅栏和保护栅栏.规范 | Industrial type flooring and stair treads - Glass reinforced plastics (GRP) moulded open mesh gratings and protective barriers - Specification |
| BS 4618 Introduction-1970 | 塑料设计数据表示方法推荐标准.总则 | Recommendations for the presentation of plastics design data - General introduction |
| BS 4618-1.1-1970 | 塑料设计数据表示方法推荐标准.第1部分:机械特性.第1节:蠕变 | Recommendations for the presentation of plastics design data - Mechanical properties - Creep |
| BS 4618-1.1.1-1970 | 塑料设计数据表示方法推荐标准.第1部分:机械性能.第1节:蠕变.第1小节:单轴拉伸或压缩蠕变(专指固体塑料) | Recommendations for the presentation of plastics design data - Mechanical properties - Creep in uniaxial tension or compression (with particular reference to solid plastics) |
| BS 4618-1.1.2-1976 | 塑料设计数据表示方法推荐标准.第1部分:机械特性.第 1节:蠕变.第 2小节:低应变挠曲蠕变 | Recommendations for the presentation of plastics design data - Mechanical properties - Creep in flexure at low strains |
| BS 4618-1.1.3-1974 | 塑料设计数据表示方法推荐标准.第1部分:机械特性.第1节:蠕变.第 3小节:蠕变横向收缩比(泊松比) | Recommendations for the presentation of plastics design data - Mechanical properties - Creep lateral contraction ratio (Poisson's ratio) |
| BS 4618-1.2-1972 | 塑料设计数据表示方法推荐标准.第1部分:机械特性.第2节:冲击性能 | Recommendations for the presentation of plastics design data - Mechanical properties - Impact behaviour |
| BS 4618-1.3-1975 | 塑料设计数据表示方法推荐标准.第1部分:机械特性.第3节:强度 | Recommendations for the presentation of plastics design data - Mechanical properties - Strength |
| BS 4618-1.3.1-1975 | 塑料设计数据表示方法推荐标准.第1部分:机械特性.第3.1节:静态疲劳损坏 | Recommendations for the presentation of plastics design data - Mechanical properties - Static fatigue failure |
| BS 4618-1.3.3-1976 | 塑料设计数据表示方法推荐标准.第1部分:机械特性.第 3节:强度.第 3小节:环境应力破裂 | Recommendations for the presentation of plastics design data - Mechanical properties - Environmental stress cracking |
| BS 4618-2.1-1970 | 塑料设计数据表示方法推荐标准.第2部分:电气特性.第1节:介电常数 | Recommendations for the presentation of plastics design data - Electrical properties - Permittivity |
| BS 4618-2.2-1970 | 塑料设计数据表示方法推荐标准.第2部分:电气特性.第2节:损耗角正切 | Recommendations for the presentation of plastics design data - Electrical properties - Loss tangent |
| BS 4618-2.3-1975 | 塑料设计数据表示方法推荐标准.第2部分:电气特性.第3节:体积电阻率 | Recommendations for the presentation of plastics design data - Electrical properties - Volume resistivity |
| BS 4618-2.4-1975 | 塑料设计数据表示方法推荐标准.第2部分:电气特性.第4节:表面电阻率 | Recommendations for the presentation of plastics design data - Electrical properties - Surface resistivity |
| BS 4618-3.1-1970 | 塑料设计数据表示方法推荐标准.第3部分:热特性.第1节:线性热膨胀 | Recommendations for the presentation of plastics design data - Thermal properties - Linear thermal expansion |
| BS 4618-3.2-1973 | 塑料设计数据表示方法推荐标准.第3部分:热特性.第2节:热焓 | Recommendations for the presentation of plastics design data - Thermal properties - Heat content |
| BS 4618-3.3-1973 | 塑料设计数据表示方法推荐标准.第3部分:热特性.第3节:导热性 | Recommendations for the presentation of plastics design data - Thermal properties - Thermal conductivity |
| BS 4618-4.1-1972 | 塑料设计数据表示方法推荐标准.第4部分:环境和化学效应.第1节:耐液体化学性 | Recommendations for the presentation of plastics design data - Environmental and chemical effects - Chemical resistance to liquids |
| BS 4618-4.2-1972 | 塑料设计数据表示方法推荐标准.第4部分:环境和化学效应.第2节:耐自然老化性 | Recommendations for the presentation of plastics design data - Environmental and chemical effects - Resistance to natural weathering |
| BS 4618-4.3-1974 | 塑料设计数据表示方法推荐标准.第4部分:环境和化学效应.第3节:耐光照变色性 | Recommendations for the presentation of plastics design data - Environmental and chemical effects - Resistance to colour change produced by exposure to light |
| BS 4618-4.4-1973 | 塑料设计数据表示方法推荐标准.第4部分:环境和化学效应.第4节:海上曝露效应 | Recommendations for the presentation of plastics design data - Environmental and chemical effects - The effect of marine exposure |
| BS 4618-4.5-1974 | 塑料设计数据表示方法推荐标准.第4部分:环境和化学效应.第 5节:土埋及生物侵袭对塑料的影响 | Recommendations for the presentation of plastics design data - Environmental and chemical effects - The effect on plastics of soil burial and biological attack |
| BS 4618-4.6-1974 | 塑料设计数据表示方法推荐标准.第4部分:环境和化学效应.第6节:塑料耐热性 | Recommendations for the presentation of plastics design data - Environmental and chemical effects - The thermal endurance of plastics |
| BS 4618-5.1-1970 | 塑料设计数据表示方法推荐标准.第5部分:其它特性.第1节:密度 | Recommendations for the presentation of plastics design data - Other properties - Density |
| BS 4618-5.2-1970 | 塑料设计数据表示方法推荐标准.第5部分:其它特性.第2节:吸水后线性尺寸变化 | Recommendations for the presentation of plastics design data - Other properties - Change in linear dimensions with moisture absorption |
| BS 4618-5.3-1972 | 塑料设计数据表示方法推荐标准.第5部分:其它特性.第3节:光学特性 | Recommendations for the presentation of plastics design data - Other properties - Optical properties |
| BS 4618-5.4-1972 | 塑料设计数据表示方法推荐标准.第5部分:其它特性.第4节:声学特性(机械阻尼能力) | Recommendations for the presentation of plastics design data - Other properties - Acoustical properties (mechanical damping capacity) |
| BS 4618-5.5-1974 | 塑料设计数据表示方法推荐标准.第5部分:其它特性.第5节:扩散数据 | Recommendations for the presentation of plastics design data - Other properties - Data on diffusion |
| BS 4618-5.6-1975 | 塑料设计数据表示方法推荐标准.第5部分:其它特性.第6节:滑动摩擦指南 | Recommendations for the presentation of plastics design data - Other properties - Guide to sliding friction |
| BS 4660-2000 | 地下重力排水和污水工程用公称尺寸为110和160mm的热塑塑料辅助配件 | Thermoplastics ancillary fittings of nominal sizes 110 and 160 for below ground gravity drainage and sewerage |
| BS 4781-1990 | 永久性压敏粘合塑料标签规范 | Specification for pressure-sensitive adhesive plastics labels for permanent use |
| BS 4840-1-1985 | 硬聚氨脂(PUR)泡沫塑料块.第1部分:运输集装箱和绝缘运输车身用聚氨脂(PUR)泡沫塑料规范 | Rigid polyurethane (PUR) foam in slab form - Specification for PUR foam for use in transport containers and insulated vehicle bodies |
| BS 4840-2-1994 | 硬聚氨基(PUR)泡沫塑料块.第2部分:冷藏箱、冷藏室及冷库用聚氨脂泡沫塑料规范 | Rigid polyurethane (PUR) foam in slab form - Specification for PUR foam for use in refrigerator cabinets, cold rooms and stores |
| BS 490-2-1975 | 输送机与提升机传动带.第2部分:链斗提升机用织物结构的橡胶和塑料传动带规范 | Conveyor and elevator belting - Rubber and plastics belting of textile construction for use on bucket elevators |
| BS 4901-1976 | 建筑用塑料颜色规范 | Specification for plastics colours for building purposes |
| BS 4962-1989 | 田间地下排水用塑料管和配件规范 | Specification for plastics pipes and fittings for use as subsoil field drains |
| BS 4965-1999 | 装饰叠层塑料面胶合板和镶板 | Decorative laminated plastics sheet veneered boards and panels |
| BS 4998-1985 | 模塑热塑性塑料吸尘箱(盖除外)规范 | Specification for moulded thermoplastics dustbins (excluding lids) |
| BS 5173-100-1992 | 橡胶和塑料软管及软管组件试验方法.第100部分:总则 | Method of test for rubber and plastics hoses and hose assemblies - General introduction |
| BS 5173-102.10-1990 | 橡胶和塑料软管组件的试验方法.第102部分:液压试验.第10节:吸油和放油软管静液压试验 | Methods of test for rubber and plastics hoses and hose assemblies - Hydraulic pressure tests - Hydrostatic tests for oil suction and discharge hose |
| BS 5173-102.3-1988 | 橡胶和塑料软管及软管组件试验方法.第102部分:液压试验.第3节:燃料分配泵软管体积膨胀测定 | Methods of test for rubber and plastics hoses and hose assemblies - Hydraulic pressure tests - Determination of volumetric expansion of fuel-dispensing pump hoses |
| BS 5173-102.4-1990 | 橡胶和塑料软管组件试验方法.第102部分:液压试验.第4节:液压软管体积膨胀测定 | Methods of test for rubber and plastics hoses and hose assemblies - Hydraulic pressure tests - Determination of volumetric expansion of hydraulic hoses |
| BS 5173-102.8-1987 | 橡胶和塑料软管及软管组件试验方法.第102部分:液压试验.第8节:硬质增强热塑性塑料螺旋管压力脉冲试验 | Methods of test for rubber and plastics hoses and hose assemblies - Hydraulic pressure tests - Pressure impulse test for rigid helix reinforced thermoplastics hoses |
| BS 5173-103.13-1994 | 橡胶和塑料软管及软管组件试验方法.第103部分:物理试验.第13节:抗燃性测定 | Methods of test for rubber and plastics hoses and hose assemblies - Physical tests - Determination of resistance to fire |
| BS 5173-103.2-1990 | 橡胶和塑料软管组件的试验方法.第103部分:物理试验.第2节:软管耐磨损性测定 | Methods of test for rubber and plastics hoses and hose assemblies - Physical tests - Determination of crush resistance of hoses |
| BS 5173-103.6-1990 | 橡胶和塑料软管组件的试验方法.第103部分:物理试验.第6节:衬料可燃性测定 | Methods of test for rubber and plastics hoses and hose assemblies - Physical tests - Determination of ignitability of lining |
| BS 5173-103.7-1991 | 橡胶和塑料软管组件的试验方法.第103部分:物理试验.第7节:热塑软管用刚性聚合物螺纹钢筋耐断裂性测定 | Methods of test for rubber and plastics hoses and hose assemblies - Physical tests - Determination of fracture resistance of rigid polymer helical reinforcement in thermoplastics hoses |
| BS 5173-106.2-1990 | 橡胶和塑料软管组件的试验方法.第106部分:环境试验.第2节:高温老化试验一般要求 | Methods of test for rubber and plastics hoses and hose assemblies - Environmental tests - General requirements for high temperature ageing tests |
| BS 5241-1-1994 | 建筑工地涂覆或喷涂用硬质聚氯酯泡沫塑料.第1部分:外部施覆的隔热泡沫塑料 | Rigid polyurethane (PUR) and polyisocyanurate (PIR) foam when dispensed or sprayed on a construction site - Specification for sprayed foam thermal insulation applied externally |
| BS 5241-2-1991 | 施工现场配制与喷涂用硬聚氨酯和聚异三聚氰脲酸酯泡沫塑料.第2部分:绝热或弹性配制泡沫塑料的规范 | Rigid polyurethane (PUR) and polyisocyanurate (PIR) foam when dispensed or sprayed on a construction site - Specification for dispensed foam for thermal insulation or buoyancy applications |
| BS 5255-1989 | 热塑性塑料废水管及配件规范 | Specification for thermoplastics waste pipe and fittings |
| BS 5404-1-1976 | 实验室塑料容器规范.第1部分:烧杯 | Specification for plastics laboratory ware - Beakers |
| BS 5404-2-1977 | 实验室塑料容器规范.第2部分:带刻度量筒 | Specification for plastics laboratory ware - Graduated measuring cylinders |
| BS 5404-3-1977 | 实验室塑料容器规范.第3部分:滤液漏斗 | Specification for plastics laboratory ware - Filter funnels |
| BS 5404-4-1979 | 实验室塑料容器规范.第4部分:洗涤瓶 | Specification for plastics laboratory ware - Wash bottles |
| BS 5452-1977 | 医院用塑料凹形器皿规范 | Specification for hospital hollow-ware made of plastics material |
| BS 5597-1991 | 容量可达1000ml一次使用的塑料气溶胶分配器规范 | Specification for non-refillable plastics aerosol dispensers up to 1000 mL capacity |
| BS 5617-1985 | 适用于砖砌或混凝土内外层空心墙保温的脲甲醛(UF)泡沫塑料规范 | Specification for urea-formaldehyde (UF) foam systems suitable for thermal insulation of cavity walls with masonry or concrete inner and outer leaves |
| BS 5618-1985 | 填充脲甲醛(UF)泡沫塑料的空心墙(具有砖砌或混凝土内外层)保温实用规程 | Code of practice for thermal insulation of cavity walls (with masonry or concrete inner and outer leaves) by filling with urea-formaldehyde (UF) foam systems |
| BS 5627-1984 | 水平排水陶瓷抽水马桶用塑料连接件规范 | Specification for plastics connectors for use with horizontal outlet vitreous china WC pans |
| BS 5734-5-1990 | 电工和其它用途用聚酯模塑料.第5部分:机械用玻璃纤维增强热固性塑料片材规范 | Polyester moulding compounds for electrical and other purposes - Specification for sheet moulding compounds for mechanical purposes |
| BS 5946-1980 | 测定苯酚-甲醛泡沫塑料燃烧特性的试验方法 | Method of test for determination of the punking behaviour of phenol-formaldehyde foam |
| BS 5955-8-2001 | 塑料管道工程(热塑性材料).家用冷、热水设施和建筑物中加热系统用的热塑性塑料管道工程及其配件的安装规范 | Plastics pipework (thermoplastics materials) - Specification for the installation of thermoplastic pipes and associated fittings for use in domestic hot and cold services and heating systems in buildings |
| BS 5961-1980 | 电绝缘用塑料薄膜及薄片摩擦系数测定方法 | Method for determination of coefficients of friction of plastic film and sheeting for use as electrical insulation |
| BS 611-2-1990 | 陪替氏培养皿.第2部分:一次使用的陪替氏塑料培养皿规范 | Petri dishes - Specification for plastics Petri dishes for single use |
| BS 6206-1981 | 建筑物用安全平板玻璃及安全塑料的耐冲击性能要求规范 | Specification for impact performance requirements for flat safety glass and safety plastics for use in buildings |
| BS 6374-1-1985 | 加工工业用聚合材料设备衬套.第1部分:热塑塑料片制衬套规范 | Lining of equipment with polymeric materials for the process idustries - Specification for lining with sheet thermoplastics |
| BS 6374-2-1984 | 加工工业用聚合材料设备衬套.第2部分:非热塑性塑料片制衬套规范 | Lining of equipment with polymeric materials for the process industries - Specification for lining with non-sheet applied thermoplastics |
| BS 6464-1984 | 制炼厂用增强塑料管、配件和接头规范 | Specification for reinforced plastics pipes, fittings and joints for process plants |
| BS 6586-1-1993 | 采用压注法制作的聚氨酯硬泡沫塑料.第1部分:运输集装箱和车身用隔离板的聚氨酯硬泡沫塑料规范 | Rigid polyurethane (PUR) foam produced by the press injection method - Specification for PUR foam for insulated panels for transport containers and insulated vehicles bodies |
| BS 6642-1985 | 一次使用的聚乙烯塑料垃圾袋规范 | Specification for disposable plastics refuse sacks made from polyethylene |
| BS 7010-1988 | 塑料模压件尺寸公差系统的实用规程 | Code of practice for a system of tolerances for the dimensions of plastics mouldings |
| BS 7029-1-1993 | 热塑性塑料注射模制品规定方法.第1部分:一般要求 | Method of specifying thermoplastics injection mouldings - General requirements |
| BS 7029-2-1993 | 热塑性塑料注射模制品规定方法.第2部分:聚碳酸酯,聚酰胺和聚乙烯模制品的附加要求 | Method of specifying thermoplastics injection mouldings - Additional requirements for polycarbonate, polyamide and polyethylene mouldings |
| BS 7158-2001 | 排放物和污物用的塑料制检查容器 | Plastics inspection chambers for drains and sewers - Specification |
| BS 7159-1989 | 特殊工厂或工地用玻璃纤维增强塑料管道系统的设计和建造实用规程 | Code of practice for design and construction of glass-reinforced plastics (GRP) piping systems for individual plants or sites |
| BS 7251-14-1998 | 矫形外科关节假体.部分和整体膝关节假体部件.由金属、陶瓷和塑料材料制成的铰接表面 | Orthopaedic joint prostheses - Components for partial and total knee-joint prostheses - Articulating surfaces made of metal, ceramic and plastics materials |
| BS 7251-4-1997 | 矫形外科关节假体.第4部分:采用金属、陶瓷和塑料材料制作的髋关节假体连接表面规范 | Orthopaedic joint prostheses - Specification for articulating surfaces made of metallic, ceramic and plastics materials of hip joint prostheses |
| BS 7379-1991 | 塑料/金属叠层可涨缩软管规范 | Specification for plastics/metal laminate collapsible tubes |
| BS 7414-1991 | 塑料窗用带热焊拐角连接的聚氯乙烯U型挤压空心型材外型规范:B型材料 | Specification for white PVC-U extruded hollow profiles with heat welded corner joints for plastics windows: materials type B |
| BS 7442-0-1991 | 橡胶或塑料涂层辊子.第0部分:导言 | Rubber or plastics covered rollers - Introduction |
| BS 7442-1-1991 | 有橡胶或塑料涂层的辊子.术语词汇 | Rubber or plastics covered rollers - Glossary of terms |
| BS 7442-2-1991 | 有橡胶或塑料涂层的辊子.第2部分:由买方提供的技术信息推荐标准 | Rubber or plastics covered rollers - Recommendations for technical information to be provided by the purchaser |
| BS 7442-4.1-1992 | 有橡胶或塑料涂层辊子.要求.表观硬度规范 | Rubber or plastics covered rollers - Requirements - Specification for apparent hardness |
| BS 7442-4.2-1994 | 有橡胶或塑料涂层的辊子.要求.表面精度分类 | Rubber or plastics covered rollers - Requirements - Classification by surface finish |
| BS 7442-4.3-1993 | 有橡胶或塑料涂层辊子.第4部分:要求.第3节:尺寸公差规范 | Rubber or plastics covered rollers - Requirements - Specification for dimensional tolerances |
| BS 7825-3.1-1997 | 橡胶和塑料试验设备的校正.校正一览表.热性能 | Calibration of rubber and plastics test equipment - Calibration schedules - Thermal properties |
| BS 7825-3.10-1998 | 橡胶和塑料试验设备的校准.校准一览表.调节、样品及试样制备 | Calibration of rubber and plastics test equipment - Calibration schedules - Conditioning, sample and test piece preparation |
| BS 7825-3.11-1998 | 橡胶和塑料试验设备的校准.校准一览表.橡胶聚合物的识别和化学性能 | Calibration of rubber and plastics test equipment - Calibration schedules - Rubber polymer identification and chemical properties |
| BS 7825-3.2-1997 | 橡胶和塑料试验设备的校准.校准一览表.电气性能 | Calibration of rubber and plastics test equipment - Calibration schedules - Electrical properties |
| BS 7825-3.3-1997 | 橡胶和塑料试验设备的校准.校准一览表.塑料的机械性能 | Calibration of rubber and plastics test equipment - Calibration schedules - Mechanical properties of plastics |
| BS 7825-3.4-1998 | 橡胶和塑料试验设备的校准.校准一览表.橡胶的机械性能 | Calibration of rubber and plastics test equipment - Calibration schedules - Mechanical properties of rubber |
| BS 7825-3.5-1997 | 橡胶和塑料试验设备的校准.校准一览表.光学和风化性能 | Calibration of rubber and plastics test equipment - Calibration schedules - Optical and weathering properties |
| BS 7825-3.6-1997 | 橡胶和塑料试验设备的校准.校准一览表.尺寸性能 | Calibration of rubber and plastics test equipment - Calibration schedules - Dimensional properties |
| BS 7825-3.7-1998 | 橡胶和塑料试验设备的校准.校准一览表.流变性能 | Calibration of rubber and plastics test equipment - Calibration schedules - Rheological properties |
| BS 7825-3.8-1998 | 橡胶和塑料试验设备的校准.校准一览表.降解和环境性能 | Calibration of rubber and plastics test equipment - Calibration schedules - Degradation and environmental properties |
| BS 7825-3.9-1998 | 橡胶和塑料试验设备的校准.校正一览表.可燃性特性 | Calibration of rubber and plastics test equipment - Calibration schedules - Flammability characteristics |
| BS 7982-2001 | 涉及塑料材料的大规模火灾的环境影响分析指南 | Guidance on the environmental impact of large-scale fires involving plastics materials |
| BS 8010-2.5-1989 | 管道的实用规程.第2部分:陆地管道:设计、制造和安装.第5节:玻璃纤维加强的热固性塑料制品 | Code of practice for pipelines - Pipelines on land: design, construction and installation - Glass reinforced thermosetting plastics |
| BS 879-2-1988 | 水井套管.第2部分:井套管和开缝井套管用热塑性塑料管规范 | Water well casing - Specification for thermoplastics tubes for casing and slotted casing |
| BS CECC 00808-1996 | 电子元件用质量评估协调体系.指南文件:塑料压缩设备的应用 | Harmonized system of quality assessment for electronic components - Guidance document: use and application of plastic encapsulated devices |
| BS DD CEN ISO/TS 15874-7-2006 | 冷热水装置用塑料管道系统.聚丙烯(PP).合格评定指南 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Guidance for the assessment of conformity |
| BS DD CEN ISO/TS 15875-7-2006 | 冷热水装置用塑料管道系统.交联聚乙烯(PE-X).合格评定指南 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Guidance for the assessment of conformity |
| BS DD CEN ISO/TS 15876-7-2006 | 冷热水装置用塑料管道系统.聚丁烯(PB).合格评定指南 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Guidance for the assessment of conformity |
| BS DD CEN ISO/TS 15877-7-2006 | 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).合格评定指南 | Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Guidance for the assessment of conformity |
| BS DD CEN/TS 12200-2-2003 | 地上外部用塑料雨水管道系统.未增塑聚氯乙烯管.符合性评定指南 | Plastics rainwater piping systems for above ground external use - Unplasticized poly (vinyl chloride) (PVC-U) - Guidance for the assessment of conformity |
| BS DD CEN/TS 12666-2-2005 | 非承压地下排放和污水用塑料管道系统.聚乙烯(PE).符合性评定指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity |
| BS DD CEN/TS 13130-10-2005 | 和食品接触的材料和物品.受限制的塑料物质.食品模拟物中丙烯酰胺的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of acrylamide in food simulants |
| BS DD CEN/TS 13130-11-2005 | 和食品接触的材料和物品.受限制的塑料物质.食品模拟物中11-aminoundecanoic酸的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of 11-aminoundecanoic acid in food simulants |
| BS DD CEN/TS 13130-12-2005 | 与食品接触的材料和物品.受限制的塑料物质.食品模拟物中1,3-benzenedimethaneamine的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of 1, 3-benzenedimethaneamine in food simulants |
| BS DD CEN/TS 13130-13-2005 | 与食品接触的材料和物品.受限制的塑料物质.食品模拟物中2,2-双(4-羟苯基)丙烷(双酚A)的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of 2, 2-bis(4-hydroxyphenyl)propane (Bisphenol A) in food simulants |
| BS DD CEN/TS 13130-14-2005 | 与食品接触的材料和物品.受限制的塑料物质.食品模拟物中3,3-双(3-甲基-4-羟苯基)2-indolinone的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of 3, 3-bis(3-methyl-4-hydroxyphenyl)2-indolinone in food simulants |
| BS DD CEN/TS 13130-15-2005 | 和食品接触的材料和物品.受限制的塑料物质.食品模拟物中1,3-丁二烯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of 1,3-butadiene in food simulants |
| BS DD CEN/TS 13130-16-2005 | 和食品接触的材料和物品.受限制的塑料物质.食品模拟物中己内酰胺和己内酰胺盐的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of caprolactam and caprolactam salt in food simulants |
| BS DD CEN/TS 13130-17-2005 | 和食品接触的材料和物品.受限制的塑料物质.塑料中碳酰氯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of carbonyl chloride in plastics |
| BS DD CEN/TS 13130-18-2005 | 与食品接触的材料和物品.受限制的塑料物质.食品模拟物中1,2-苯二酚、1,3-苯二酚、1,4-苯二酚、4,4'-二羟二 | Materials and articles in contact with foodstuffs — Plastics substances subject to limitation — Part 18: Determination of 1,2 dihydroxybenzene, 1,3-dihydroxybenzene, 1,4-dihydroxybenzene, 4,4'-dihydroxybenzophenone and 4,4'dihydroxybiphenyl in food simulants |
| BS DD CEN/TS 13130-19-2005 | 和食品接触的材料和物品.受限制的塑料物质.食品模拟物中二甲氨基乙醇的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of dimethylaminoethanol in food simulants |
| BS DD CEN/TS 13130-20-2005 | 和食品接触的材料和物品.受限制的塑料物质.塑料中3-氯-1,2-环氧丙烷的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of epichlorohydrin in plastics |
| BS DD CEN/TS 13130-21-2005 | 和食品接触的材料和物品.受限制的塑料物质.食品模拟物中1,2-乙二胺和六亚甲基四胺的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of ethylenediamine and hexamethylenediamine in food simulants |
| BS DD CEN/TS 13130-22-2005 | 和食品接触的材料和物品.受限制的塑料物质.塑料中环氧乙烷和氧化丙烯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of ethylene oxide and propylene oxide in plastics |
| BS DD CEN/TS 13130-23-2005 | 和食品接触的材料和物品.受限制的塑料物质.食品模拟物中甲醛和六亚甲基四胺的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of formaldehyde and hexamethylenetetramine in food simulants |
| BS DD CEN/TS 13130-24-2005 | 和食品接触的材料和物品.受限制的塑料物质.食品模拟物中马来酸和顺式丁烯二酸酐的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of maleic acid and maleic anhydride in food simulants |
| BS DD CEN/TS 13130-25-2005 | 与食品接触的材料和物品.受限制的塑料物质.食品模拟物中4-甲基-1-戊烯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of 4-methyl-1-pentene in food simulants |
| BS DD CEN/TS 13130-26-2005 | 与食品接触的材料和物品.受限制的塑料物质.食品模拟物中1-辛烯和四氢呋喃的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of 1-octene and tetrahydrofuran in food simulants |
| BS DD CEN/TS 13130-27-2005 | 与食品接触的材料和物品.受限制的塑料物质.食品模拟物中2,4,6-三氨基-1,3,5-三嗪的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of 2,4,6-triamino-1, 3,5-triazine in food simulants |
| BS DD CEN/TS 13130-28-2005 | 与食品接触的材料和物品.受限制的塑料物质.食品模拟物中1,1,1-三甲醇丙烷的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of 1,1, 1-trimethylopropane in food simulants |
| BS DD CEN/TS 13130-9-2005 | 和食品接触的材料和物品.受限制的塑料物质.食品模拟物中乙酸、乙酸基乙烯酯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of acetic acid, vinyl ester in food simulants |
| BS DD CEN/TS 13476-4-2008 | 无压地下排水管和下水道用塑料管道系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)的结构壁管系统.一 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Guidance for the assessment of conformity |
| BS DD CEN/TS 14541-2007 | 非压力设备用塑料管道和配件.非原态未增塑聚氯乙烯、聚丙烯和聚乙烯材料应用 | Plastics pipes and fittings for non-pressure applications - Utilisation of non-virgin PVC-U, PP and PE materials |
| BS DD CEN/TS 1456-2-2003 | 压力下直埋式和地上排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U).一致性评估指南 | Plastic piping systems for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC-U). Guidance for the assessment of conformity |
| BS DD CEN/TS 14578-2003 | 给水或排水和下水道用塑料管道系统.基于不饱和聚酯树脂(UP)的玻璃纤维增强热固性塑料(GPR).安装的推荐实施 | Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GPR) based on unsaturated polyester resin (UP) - Recommended practice for installation |
| BS DD CEN/TS 14632-2006 | 排水、排污和供水、压力和非压力用塑料管道系统.基于聚酯树脂(UP)玻璃纤维增强热固性塑料(GPR).合格评定指 | Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Guidance for the assessment of conformity |
| BS DD CEN/TS 14758-2-2007 | 无压力地下排水和污水用塑料管道系统.含矿物调节剂的聚丙烯(PP-MD).第2部分:一致性评估用指南 | Plastics piping systemsfor non-pressureunderground drainageand sewerage —Polypropylene withmineral modifier(s)(PP-MD) —Part 2: Guidance for the assessment ofconformity |
| BS DD CEN/TS 14758-3-2006 | 无压力地下排水和排污塑料管道系统.聚丙烯矿物调节器(s)(PP-MD).安装指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3: Guidance for installation |
| BS DD CEN/TS 1852-3-2003 | 非压力地下排水和排污用塑料管道系统.聚丙烯(PP).安装指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Guidance for installation |
| BS DD ENV 12108-2001 | 塑料管道系统.建筑物内部人消费用冷热水的压力系统的安装指南 | Plastics piping systems - Guidance for the installation inside buildings of pressure systems for hot and cold water intended for human consumption |
| BS DD ENV 1329-2-2001 | 建筑内污物污水排放(高、低温)用塑料管道系统.未增塑的聚氯乙烯(PVC-U).符合性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Guidance for the assessment of conformity |
| BS DD ENV 13801-2001 | 建筑物内污物污水排放(低温和高温)用塑料管道系统.热塑管.推荐的安装实施规程 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation |
| BS DD ENV 1401-2-2001 | 非承压地下排放和污水用塑料管道系统.未增塑的聚氯乙烯(PVC-U).符合性评定指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinylchloride) (PVC-U) - Guidance for assessment of conformity |
| BS DD ENV 1401-3-2001 | 非承压地下排放和污水用塑料管道系统.未增塑的聚氯乙烯(PVC-U).安装指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinylchloride) (PVC-U) - Guidance for installation |
| BS DD ENV 1451-2-2001 | 建筑物内污物和污水排放(高、低温)用塑料管道系统.聚丙烯(PP).符合性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Guidance for the assessment of conformity |
| BS DD ENV 1452-6-2002 | 供水用的塑料管道系统.未增塑的聚氯乙烯(PVC-U).安装指南 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Guidance for installation |
| BS DD ENV 1452-7-2001 | 供水用的塑料管道系统.未增塑的聚氯乙烯(PVC-U).符合性评定指南 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Guidance for the assessment of conformity |
| BS DD ENV 1453-2-2001 | 建筑物内污物和废水排放(高、低温)用带结构壁管的塑料管道系统.未增塑的聚氯乙烯(PVC-U).符合性评定指南 | Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Guidance for the assessment of conformity |
| BS DD ENV 1455-2-2001 | 建筑物内污物污水排放(高、低温)用塑料管道系统.丙烯腈-丁二烯-苯乙烯共聚物(ABS).符合性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene- styrene (ABS) - Guidance for the assessment of conformity |
| BS DD ENV 1519-2-2001 | 建筑物内污物污水排放(高、低温)用塑料管道系统.聚乙烯(PE).符合性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Guidance for the assessment of conformity |
| BS DD ENV 1565-2-2001 | 建筑物内污物废水排放(高、低温)用塑料管道系统.苯乙烯共聚物混合物(SAN + PVC).符合性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN + PVC) - Guidance for the assessment of conformity |
| BS DD ENV 1566-2-2001 | 建筑物内污物污水排放(高、低温)用塑料管道系统.氯化聚氯乙烯(PVC-C).符合性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Guidance for the assessment of conformity |
| BS EN 1013-1-1998 | 单层屋面用发光压型塑料片材.一般要求和试验方法 | Light transmitting profiled plastic sheeting for single skin roofing - General requirements and test methods |
| BS EN 1013-2-1999 | 单层屋面用透光成型塑料薄板.玻璃纤维增强的聚酯树脂薄板的试验方法和特殊要求 | Light transmitting profiled plastic sheeting for single skin roofing - Specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP) |
| BS EN 1013-3-1998 | 单层木板屋面用发光压型塑料片材.聚氯乙烯片材的特殊要求和试验方法 | Light transmitting profiled plastic sheeting for single skin roofing - Specific requirements and test methods for sheets of polyvinyl chloride (PVC) |
| BS EN 1013-4-2000 | 单层屋顶用透光成型塑料薄板.聚碳酸酯板的特殊要求、试验方法和性能 | Light transmitting profiled plastic sheeting for single skin roofing - Specific requirements, test methods and performance of polycarbonate (PC) sheets |
| BS EN 1013-5-2000 | 单层屋顶用透光成型塑料薄板.聚甲基丙烯酸甲酯板的特殊要求、试验方法和性能 | Light transmitting profiled plastic sheeting for single skin roofing - Specific requirements, test methods and performance of polymethylmethacrylate (PMMA) sheets |
| BS EN 1053-1996 | 塑料管道系统.无压力情况下使用的热塑管道系统.防水性的检验方法 | Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test methods for watertightness |
| BS EN 1054-1996 | 塑料管道系统.建筑物内粪水和污水排放下水道用热塑管道系统.连接件的气密性试验方法 | Plastics piping systems - Thermoplastics piping systems for soil and waste discharge - Test method for airtightness of joints |
| BS EN 1055-1996 | 塑料管道系统.建筑物内粪水污排放用热塑制管道系统.耐高温度循环的试验方法 | Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling |
| BS EN 1056-1996 | 塑料管道系统.塑料管道和配件.直接(自然)风化的方法 | Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering |
| BS EN 1107-2-2001 | 防水柔性板.尺寸稳定性的测定.屋顶防水用橡胶和塑料薄板 | Flexible sheets for waterproofing - Determination of dimensional stability - Plastic and rubber sheets for roof waterproofing |
| BS EN 1114-1-1997 | 橡胶和塑料制造机器.挤压机和挤压工作线.第1部分:挤压设备的安全性要求 | Rubber and plastics machines - Extruders and extrusion lines - Safety requirements for extruders |
| BS EN 1120-1996 | 塑料管道系统.玻璃增强的热固塑料管和配件.偏离规定条件下部件内部耐化学侵蚀性能的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of a section in a deflected condition |
| BS EN 1122-2001 | 塑料.镉的测定.湿分解法 | Plastics - Determination of cadmium - Wet decomposition method |
| BS EN 1186-1-2002 | 与食品接触的材料和器具.塑料.第1部分:全渗移试验条件和试验方法选择指南 | Materials and articles in contact with foodstuffs - Plastics - Guide to the selection of conditions and test methods for overall migration |
| BS EN 1186-10-2002 | 与食品接触的材料和器具.塑料.进入橄榄油中全渗移析出量的试验方法(橄榄油不完全萃取时用的改进方法) | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration into olive oil (modified method for use in cases where incomplete extraction of olive oil occurs) |
| BS EN 1186-11-2002 | 与食品接触的材料和器具.塑料.全渗移到标记C的合成甘油三酸脂混合物的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration into mixtures of C-labelled synthetic triglycerides |
| BS EN 1186-12-2002 | 与食品接触的材料和器具.塑料.总渗移的低温试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration at low temperatures |
| BS EN 1186-13-2002 | 与食品接触的材料和制品.塑料.高温下全渗移物析出量的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration at high temperatures |
| BS EN 1186-14-2002 | 与食品接触的材料和器具.塑料.高温下全渗移物析出量的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for 'substitute tests' for overall migration from plastics intended to come into contact with fatty foodstuffs using test media iso-octane and 95% ethanol |
| BS EN 1186-15-2002 | 与食品接触的材料和制品.塑料.快速萃取异辛烷或95%酒精的脂肪食品塑料析出物渗移量的交替试验方法 | Materials and articles in contact with foodstuffs - Plastics - Alternative test methods to migration into fatty food simulants by rapid extraction into iso-octane and/or 95 % ethanol |
| BS EN 1186-2-2002 | 与食品接触的材料和器具.塑料.总渗移到橄榄油中的全浸没试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration into olive oil by total immersion |
| BS EN 1186-3-2002 | 与食品接触的材料和器具.塑料.总渗移到水状试验食品中的全浸没试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration into aqueous food simulants by total immersion |
| BS EN 1186-4-2002 | 与食品接触的材料和器具.塑料.总渗移到橄榄油中的电解槽试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration into olive oil by cell |
| BS EN 1186-5-2002 | 与食品接触的材料和器具.塑料.总渗移到水状试验食品中的电解槽试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration into aqueous food simulants by cell |
| BS EN 1186-6-2002 | 与食品接触的材料和器具.塑料.总渗移到橄榄油中的袋装试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration into olive oil using a pouch |
| BS EN 1186-7-2002 | 与食品接触的材料和器具.塑料.总渗移到水状试验食品中的袋装试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration into aqueous food simulants using a pouch |
| BS EN 1186-8-2002 | 与食品接触的材料和器具.塑料.总渗移到橄榄油中的物品充填试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration into olive oil by article filling |
| BS EN 1186-9-2002 | 与食品接触的材料和器具.塑料.总渗移到水状试验食品中的充填物品试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for overall migration into aqueous food simulants by article filling |
| BS EN 12012-1-2007+A1-2008 | 塑料和橡胶机械.粉碎机.刀片制粒机的安全要求 | Plastics and rubber machines - Size reduction machines - Safety requirements for blade granulators |
| BS EN 12012-4-2006+A1-2008 | 橡胶和塑料机械.粉碎机.第4部分:凝聚器安全要求 | Plastics and rubber machines - Size reduction machines - Part 4: Safety requirements foragglomerators |
| BS EN 12061-1999 | 塑料管道系统.热塑配件.耐冲击试验方法 | Plastics piping systems - Thermoplastics fittings - Test method for impact resistance |
| BS EN 12095-1997 | 塑料管道系统.雨水管道系统用托架.托架强度试验方法 | Plastics piping systems - Brackets for rainwater piping systems - Test method for bracket strength |
| BS EN 12099-1997 | 塑料管道系统.聚乙烯管材和组件.挥发物价改革含量的测定 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| BS EN 12100-1998 | 塑料管道系统.聚乙稀(PE)阀门.阀座间抗弯曲性的试验方法 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports |
| BS EN 12106-1998 | 塑料管道系统.聚乙稀(PE)阀门.挤压后抗内压力的试验方法 | Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off |
| BS EN 12107-1998 | 塑料管道系统.注射模塑热塑性塑料管件、阀门和辅助设备.注射模塑管道元件用热塑性材料的长期液压强度的测定 | Plastics piping systems - Injection-moulded thermoplastics fittings, valves and ancillary equipment - Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components |
| BS EN 12117-1998 | 塑料管道系统.管件、阀门和附件.气体流速与压降之间关系的测定 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| BS EN 12118-1998 | 塑料管道系统.用库仑分析法测定热塑性塑料中的水含量 | Plastics piping systems - Determination of moisture content in thermoplastics by coulometry |
| BS EN 12119-1997 | 塑料管道系统.聚乙烯(PE)阀.耐力热循环抗性的测试方法 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling |
| BS EN 12200-1-2000 | 地上外部用塑料雨水管道系统.未增塑聚氯乙烯.管道、配件和系统规范 | Plastics rainwater piping systems for above ground external use - Unplasticized poly (vinyl chloride) (PVC-U) - Specifications for pipes, fittings and the system |
| BS EN 12201-1-2003 | 供水用塑料管道系统.聚乙烯.总则 | Plastic piping systems for water supply - Polyethylene (PE) - General |
| BS EN 12201-2-2003 | 供水用塑料管道系统.聚乙烯.管道 | Plastic piping systems for water supply - Polyethylene (PE) - Pipes |
| BS EN 12201-3-2003 | 供水用塑料管道系统.聚乙烯.配件 | Plastic piping systems for water supply - Polyethylene (PE) - Fittings |
| BS EN 12201-4-2002 | 供水用塑料管道系统.聚乙烯.阀门 | Plastic piping systems for water supply - Polyethylene (PE) - Valves |
| BS EN 12201-5-2003 | 供水用塑料管道系统.聚乙烯.系统目的的适应性 | Plastic piping systems for water supply - Polyethylene (PE) - Fitness for purpose of the system |
| BS EN 12256-1998 | 塑料管道系统.热塑配件.纤维配件机械强度和柔韧性试验方法 | Plastic piping systems - Thermoplastic fittings - Test method for mechanical strength or flexibility of fabricated fittings |
| BS EN 1226-1996 | 塑料管道系统.玻璃增强的热固性塑料管.验证抗初期环状物挠曲的试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection |
| BS EN 1228-1997 | 塑料管道系统.玻璃纤维的增强热固塑料(GFK).特定初始环状刚性测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness |
| BS EN 12280-1-1998 | 橡胶或塑料涂层织物.加速老化试验.热老化 | Rubber- or plastics-coated fabrics - Accelerated ageing tests - Heat ageing |
| BS EN 12280-2-2002 | 橡胶或塑料涂层织物.加速老化试验.物理性老化:光和气候的影响 | Rubber- or plastics-coated fabrics - Accelerated ageing tests - Physical ageing: effect of light or weathering |
| BS EN 12280-3-2002 | 橡胶或塑料涂层织物.加速老化试验.环境老化 | Rubber- or plastics-coated fabrics - Accelerated ageing tests - Environmental ageing |
| BS EN 1229-1997 | 塑料管道系统.玻璃增强的热固性塑料管.验证短期内部压力下墙的密封性试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure |
| BS EN 12293-2000 | 塑料管道系统.热水和冷水用热塑管和配件.已安装的组件耐温度变化性能的试验方法 | Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling |
| BS EN 12294-2000 | 塑料管道系统.热水和冷水系统.真空渗漏性试验方法 | Plastic piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum |
| BS EN 12295-2000 | 塑料管道系统.热水和冷水用热塑管和附属配件.连接件耐压力变化的试验方法 | Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling |
| BS EN 12310-2-2000 | 防水柔性板.抗撕裂性测定(钉杆).屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of resistance to tearing (nail shank) - Plastic and rubber sheets for roof waterproofing |
| BS EN 12311-2-2000 | 防水柔性板.拉伸性能的测定.屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of tensile properties - Plastic and rubber sheets for roof waterproofing |
| BS EN 12316-2-2000 | 防水柔性板.接头抗剥离性的测定.屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of peel resistance of joints - Plastic and rubber sheets for roof waterproofing |
| BS EN 12317-2-2000 | 防水柔性板.屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing |
| BS EN 12332-1-1999 | 橡胶或塑料涂覆织物.破裂强度测定.钢球法 | Rubber- or plastics-coated fabrics - Determination of bursting strength - Steel ball method |
| BS EN 12332-2-2002 | 橡胶或塑料涂覆织物.抗破碎强度的测定.液压法 | Rubber- or plastics-coated fabrics - Determination of bursting strength - Hydraulic method |
| BS EN 12409-2008 | 塑料和橡胶机械.加热成形机.安全要求 | Plastics and rubber machines - Thermoforming machines - Safety requirements |
| BS EN 1254-3-1998 | 铜和铜合金.管路接头.与塑料管一起使用的压合接头 | Copper and copper alloys - Plumbing fittings - Fittings with compression ends for use with plastics pipes |
| BS EN 12575-1998 | 塑料.热固模塑复合物.SMC中纤维浸湿度测定 | Plastics - Thermoset moulding compounds - Determination of the degree of fibre wet out in SMC |
| BS EN 12576-1998 | 塑料.纤维增强复合物.SMC、BMC和DMC的压缩模制试验板的预先制备 | Plastics - Fibre reinforced composites - Preparation of compression moulded test plates of SMC, BMC and DMC |
| BS EN 12666-1-2005 | 无压力地下排水和排污塑料管道系统.聚乙烯(PE).第1部分:管、管件和系统用规范 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| BS EN 12691-2006 | 防水柔性薄板.屋顶防水用沥青、塑料和橡胶薄板.抗冲击性的测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to impact |
| BS EN 12708-2000 | 标称容量为20升至225升的塑料容器用塞/盖封闭系统 | Plug/bung closure systems for plastics containers with a nominal capacity of 20 l to 225 l |
| BS EN 12709-2000 | 塑料圆桶.额定容量为20L至120L圆形截面的固定桶盖(密封盖)的圆桶 | Plastic drums - Non-removable head (tight head) circular cross-section drums with a nominal capacity of 20 l to 120 l |
| BS EN 12712-2000 | 塑料油桶.托板尺寸为800mmX1200mm,1000mmX1200mm,1140mmX1140mm的最优利用的公称容量为20升至60升的油桶 | Plastics jerricans - Jerricans with a nominal capacity of 20 l to 60 l for optimal utilization of pallet sizes 800 mm x 1200 mm, 1000 mm x 1200 mm and 1140 mm x 1140 mm |
| BS EN 12713-2000 | 标称容量为20升至60升的塑料容器的螺纹帽封闭系统 | Screw cap closure systems for plastics containers with a nominal capacity of 20 L to 60 L |
| BS EN 12730-2001 | 防水柔性板.屋顶防水用沥青,塑料和橡胶薄板.耐静负载性的测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to static loading |
| BS EN 12759-2001 | 橡胶或塑料涂覆织物.耐液体性能测定 | Rubber- or plastic-coated fabrics - Determination of resistance to liquids |
| BS EN 1277-2004 | 塑料管道系统.地下无压用热塑性管道系统.弹性密封环型接头密封性的试验方法 | Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints |
| BS EN 12877-1-2000 | 塑料中的染色材料.塑料中染色材料在处理过程中颜色的热稳定性测定.一般说明 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - General introduction |
| BS EN 12877-2-2000 | 塑料中的染色材料.塑料中染色材料在处理过程中颜色的热稳定性测定.喷射模塑测定法 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Determination by injection moulding |
| BS EN 12877-3-2000 | 塑料中的染色材料.塑料中染色材料在处理过程中颜色的热稳定性测定.耐热试验测定法 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Determination by oven test |
| BS EN 12877-4-2000 | 塑料中的染色材料.塑料中染色材料在处理过程中颜色的热稳定性测定.双辊磨测定法 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Determination by two-roll milling |
| BS EN 12943-2000 | 热塑塑料用填充材料.范围、名称与符号、要求和试验 | Filler materials for thermoplastics - Scope, designation, requirements, tests |
| BS EN 1296-2001 | 防水柔性板.屋顶用沥青,塑料和橡胶薄板.长期暴露于提高温的人工老化试验 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roofing - Method of artificial ageing by long term exposure to elevated temperature |
| BS EN 1297-2004 | 防水用软薄板.屋顶防水用沥青、塑料和橡胶薄板.长期暴露于紫外线辐射、升温和水雨综合条件的人工老化法 | Flexible sheets for waterproofing — Bitumen, plastic and rubber sheets for roof waterproofing — Method of artificial ageing by long term exposure to the combination of UV radiation, elevated temperature and water |
| BS EN 13067-2003 | 塑料焊接人员.焊工的资格检验.热塑塑料焊接组件 | Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies |
| BS EN 13117-1-2000 | 运输包装.可重复使用的刚性塑料配送箱.通用配送箱 | Transport packaging - Reusable, rigid plastics distribution boxes - General purpose application |
| BS EN 13117-2-2000 | 运输包装.可重复使用的刚性塑料配送箱.通用试验规范 | Transport packaging - Reusable, rigid plastics distribution boxes - General specifications for testing |
| BS EN 13130-1-2004 | 接触食品的材料和物品.有限制的塑料物质.物质从塑料向食品和食品模拟物中迁移的试验方法和塑料中物质的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Guide to test methods for the specific migration of substances from plastics to foods and food simulants and the determination of substances in plastics and the selection of conditions of exposure to food simulants |
| BS EN 13130-2-2004 | 接触食品的材料和物品.有限制的塑料物质.食品模拟物中对苯二酸的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of terephthalic acid in food simulants |
| BS EN 13130-3-2004 | 接触食品的材料和物品.有限制的塑料物质.食品和食品模拟物中丙烯腈的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of acrylonitrile in food and food simulants |
| BS EN 13130-4-2004 | 接触食品的材料和物品.有限制的塑料物质.塑料中1,3-丁二烯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of 1,3-butadiene in plastics |
| BS EN 13130-5-2004 | 接触食品的材料和物品.有限制的塑料物质.食品模拟物中的偏二氯乙烯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of vinylidene chloride in food simulants |
| BS EN 13130-6-2004 | 与食品有关的材料和物品.有限制的塑料物质.塑料中偏二氯乙烯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of vinylidene chloride in plastics |
| BS EN 13130-7-2004 | 与食品有关的材料和物品.有限制的塑料物质.食品模拟物中的单乙二醇和二甘醇的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of monoethylene glycol and diethylene glycol in food simulants |
| BS EN 13130-8-2004 | 接触食品的材料和物品.有限制的塑料物质.塑料中异氰酸酯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Determination of isocyanates in plastics |
| BS EN 13244-1-2003 | 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.总则 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - General |
| BS EN 13244-2-2003 | 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.管道 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Pipes |
| BS EN 13244-3-2003 | 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.配件 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Fittings |
| BS EN 13244-4-2003 | 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.阀门 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Valves |
| BS EN 13244-5-2003 | 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.系统目的的适合性 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Fitness for purpose of the system |
| BS EN 13245-1-2004 | 塑料.建筑物用未增塑聚氯乙烯异型材.淡色异型材的名称与符号 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Designation of light coloured profiles |
| BS EN 13245-2-2008 | 塑料.建筑物用未增塑聚氯乙烯异型材.内外墙和天花板精整用PVC-U型材和PVC-UE型材 | Plastics —Unplasticizedpoly(vinyl chloride)(PVC-U) profiles forbuilding applicationsPart 2: PVC-U profiles and PVC-UEprofiles for internal and external walland ceiling finishes |
| BS EN 1329-1-2000 | 建筑物结构内粪水和废水排放(低和高温)用塑料管道系统.未增塑的聚氯乙烯(PVC-U).管道,配件和系统规范 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Specifications for pipes, fittings and the system |
| BS EN 13360-2002 | 橡胶或塑料涂层织物.术语 | Rubber- or plastics-coated fabrics - Terminology |
| BS EN 13416-2001 | 防水柔性板.屋顶防水用沥青、塑料和橡胶薄板.抽样规则 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Rules for sampling |
| BS EN 13418-2004 | 橡胶和塑料机械.薄膜和薄板的卷切机.安全要求 | Rubber and plastics machines - Winding machines for film or sheet - Safety requirements |
| BS EN 13421-2006 | 塑料.热模化合物.复合和增强纤维.压模化合物的向异性能测定用试样制备 | Plastics - Thermoset moulding compounds - Composites and reinforcement fibres - Preparation of specimens for determining the anisotropy of the properties of compression moulding composites |
| BS EN 13476-1-2007 | 无压地下排水和污水塑料管系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管系统.第1部分:一般 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characteristics |
| BS EN 13476-2-2007 | 无压地下排水和污水塑料管系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管系统.第2部分:A型、 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A |
| BS EN 13476-3-2007+A1-2009 | 无压地下排水和污水塑料管系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管系统.B型、有平滑内 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3:Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B |
| BS EN 13483-2005 | 已测定的燃料分配系统用带内部蒸气回收的橡胶和塑料软管和软管组件.规范 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification |
| BS EN 13566-1-2002 | 地下无压排水管网和污水管网翻新用塑料管道系统.总则 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - General |
| BS EN 13566-2-2005 | 地下非压力排水和排污网修缮用塑料管道系统.第2部分:连续管加衬 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 2: Lining with continuous pipes |
| BS EN 13566-3-2002 | 地下无压排水管网和污水管网翻新用塑料管道系统.紧密配合管加衬 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Lining with close fit pipes |
| BS EN 13566-4-2002 | 地下无压排水管网和污水管网翻新用塑料管道系统.现场加工管衬里 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Lining with cured-in-place pipes |
| BS EN 13566-7-2007 | 地下无压排水管网和污水管网翻新用塑料管道系统.螺旋卷式管内衬 | Plastics piping systemsfor renovation ofundergroundnon-pressure drainageand seweragenetworks —Part 7: Lining with spirally-woundpipes |
| BS EN 13583-2001 | 防水柔性板.屋顶防水用沥青、塑料和橡胶薄板.防冰雹的测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of hail resistance |
| BS EN 13592-2003 | 家庭废物收集用塑料袋.类型、要求和试验方法 | Plastics sacks for household waste collection - Types, requirements and test methods |
| BS EN 13598-1-2003 | 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE).第1部分:包括浅层检 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Specifications for ancillary fittings including shallow inspection chambers |
| BS EN 13598-2-2009 | 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE).交通范围和地下设施 | Plastics pipingsystems for nonpressureundergrounddrainage and sewerage— Unplasticizedpoly(vinyl chloride) (PVC-U),polypropylene (PP)and polyethylene (PE)Part 2: Specifications for manholes andinspection chambers in traffic areasand deep underground installations |
| BS EN 1360-2005 | 计量的燃料配送系统用橡胶和塑料软管和软管组件.规范 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification |
| BS EN 13655-2002 | 塑料.农业和园艺用热塑性塑料薄膜覆盖物 | Plastics - Mulching thermoplastic films for use in agriculture and horticulture |
| BS EN 13677-1-2003 | 增强的热塑塑料模塑复合材料.GMT规范.名称 | Reinforced thermoplastic moulding compounds - Specification for GMT - Designation |
| BS EN 13677-2-2003 | 增强的热塑塑料模塑复合材料.GMT规范.试验方法和一般要求 | Reinforced thermoplastic moulding compounds - Specification for GMT - Methods of test and general requirements |
| BS EN 13677-3-2003 | 增强的热塑塑料模塑复合材料.GMT规范.特殊要求 | Reinforced thermoplastic moulding compounds - Specification for GMT - Specific requirements |
| BS EN 13689-2003 | 改建用塑料管道系统的分类和设计指南 | Guidance on the classification and design of plastics piping systems used for renovation |
| BS EN 13706-1-2002 | 增强塑料复合材料.挤拉制型材规范.命名 | Reinforced plastics composites - Specifications for pultruded profiles - Designation |
| BS EN 13706-2-2002 | 增强塑料复合物.挤拉成型规范.一般要求和试验方法 | Reinforced plastics composites - Specifications for pultruded profiles - Method of test and general requirements |
| BS EN 13706-3-2002 | 增强塑料复合物.挤拉成型规范.特殊要求 | Reinforced plastics composites - Specifications for pultruded profiles - Specific requirements |
| BS EN 13887-2003 | 结构胶粘剂.胶粘剂粘结前金属和塑料表面制备指南 | Structural adhesives - Guidelines for surface preparation of metals and plastics prior to adhesive bonding |
| BS EN 13900-1-2003 | 颜料和填充剂.扩散方法和在塑料中可扩散性的评估.概述 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - General introduction |
| BS EN 13900-2-2003 | 颜料和填充剂.扩散方法和在塑料中可扩散性的评估.用两辊磨压测定色彩特点和在增塑聚氯乙烯中的易扩散性 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Determination of colouristic properties and ease of dispersion in plasticized polyvinyl chloride by two-roll milling |
| BS EN 13900-3-2003 | 颜料和填充剂.扩散方法和在塑料中可扩散性的评估.用两辊磨压法测定色彩特点和炭黑及彩色颜料在聚乙烯中的易 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Determination of colouristic properties and ease of dispersion of black and colour pigments in polyethylene by two-roll milling |
| BS EN 13900-4-2004 | 颜料和填充剂.扩散方法和在塑料中可扩散性的评定.用双辊研磨机测定聚乙烯中白颜料的颜色性能和易扩散性 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Determination of colouristic properties and ease of dispersion of white pigments in polyethylene by two-roll milling |
| BS EN 13900-5-2005 | 颜料和填充剂.扩散方法和在塑料中可扩散性的评定.用压滤值试验测定 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Determination by filter pressure value test |
| BS EN 1393-1997 | 塑料管道系统.玻璃增强热固性塑料(GRP)管.初始轴向拉伸特性的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial longitudinal tensile properties |
| BS EN 1394-1997 | 塑料管道系统.玻璃纤维增强热固性塑料(GRP)管.外表初始圆周抗拉强度的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength |
| BS EN 13948-2007 | 防水柔性薄板材.屋顶防水用沥青、塑料和橡胶薄板材.根部防渗透性测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to root penetration |
| BS EN 13956-2005 | 防水用弹性薄板.屋顶防水用塑料和橡胶薄板.定义和特性 | Flexible sheet for waterproofing - Plastic and rubber sheets for roof waterproofing - Definitions and characteristics |
| BS EN 13967-2004+A1-2006 | 防水用软质薄板材.包括塑料和橡胶地下室薄板材的塑料和橡胶防水薄板材.定义和特性 | Flexible sheets for waterproofing - Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet - Definitions and characteristics |
| BS EN 13972-2002 | 硬质塑料容器.公称、充满和总容量的定义.公称、充满和总容量的测量 | Rigid plastic containers - Definition of nominal, brimful and total capacity and measurement of brimful and total capacity |
| BS EN 13973-2002 | 硬质塑料容器.排水性能的测定方法 | Rigid plastics containers - Method for determination of drainability |
| BS EN 13974-2002 | 硬质塑料容器.尺寸、重量和体积的公差规范 | Rigid plastics containers - Specification of tolerance for dimensions, weight and volume |
| BS EN 13984-2004+A1-2006 | 防水用软薄板.塑料和橡胶蒸汽控制层.定义和特性 | Flexible sheets for waterproofing - Plastic and rubber vapour control layers - Definitions and characteristics |
| BS EN 1411-1996 | 塑料管和导管系统.热塑性塑料管.用梯级法测定抗外部冲击性能 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of resistance to external blows by the staircase method |
| BS EN 14233-2002 | 与食品接触的材料和器具.塑料.为了选择渗移测试的适当温度,在微波炉或传统炉加热过程中塑料和食品接触面塑 | Materials and articles in contact with foodstuffs - Plastics - Determination of temperature of plastics materials and articles at the plastics/food interface during microwave and conventional oven heating in order to select the appropriate temperature for migration testing |
| BS EN 14364-2006+A1-2008 | 地下压力排水和排污水塑料管道系统.不饱和聚酯树脂(UP)玻璃纤维增强的热固性塑料(GRP).管道、配件和连接件 | Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints |
| BS EN 1437-2003 | 塑料管道系统.地下排水排污用管道系统.耐组合温度循环和外加负荷的试验方法 | Plastics piping systems - Piping systems for underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading |
| BS EN 14401-2004 | 硬塑料容器.闭塞物有效性的试验方法 | Rigid plastics containers — Methods to test the effectiveness of closures |
| BS EN 14408-1-2004 | 地下供气网翻新用塑料管道系统.第1部分:总则 | Plastics piping systems for renovation of underground gas supply networks - Part 1: General |
| BS EN 14408-3-2004 | 地下供气网翻新用塑料管道系统.第3部分:紧密配合管衬里 | Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes |
| BS EN 14409-1-2004 | 地下供水网翻新用塑料管道系统.第1部分:总则 | Plastics piping systems for renovation of underground water supply networks - Part 1: General |
| BS EN 14409-3-2004 | 地下供水网翻新用塑料管道系统.第3部分:紧密配合管衬里 | Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close fit pipes |
| BS EN 14447-2005 | 纤维增强塑料.玻璃垫增强热塑性塑料(GMT).测定流动性和固化性 | Fibre reinforced plastics - Glass mat reinforced thermoplastics (GMT) - Determination of flowability and solidification |
| BS EN 14471-2005 | 烟囱.带塑料烟道衬的整体烟囱.要求和试验方法 | Chimneys - System chimneys with plastic flue liners - Requirements and test methods |
| BS EN 14481-2003 | 接触食品的材料和物品.塑料.接触脂肪测定的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for the determination of fatty contact |
| BS EN 1451-1-2000 | 建筑物结构内粪水和废水排出(低和高温)用塑料管道系统.聚丙烯(PP).管道,配件和系统规范 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Specifications for pipes, fittings and the system |
| BS EN 1453-1-2000 | 建筑物内粪水和废水排放(低和高温)用的结构墙壁管道的塑料管道系统.非增塑的聚氯乙烯(PVC-U)的管道和系统规 | Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly (vinyl chloride) (PVC-U) - Specifications for pipes and the system |
| BS EN 1455-1-2000 | 建筑物结构内的污物和废水(低和高温)排出用塑料管道系统.丙烯腈-丁二烯-苯乙烯共聚物.管道,配件和系统规范 | Plastics piping systems for soil and waste (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Specifications for pipes, fittings and the system |
| BS EN 14598-1-2005 | 增强热固性模塑化合物.模压塑料板材(SMC)和模塑料块(BMC)的规范.名称与符号 | Reinforced thermosetting moulding compounds - Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) - Designation |
| BS EN 14598-2-2005 | 增强热固性模压复合物.模压塑料板材(SMC)和模塑料块(BMC)规范.试验方法和一般要求 | Reinforced thermosetting moulding compounds - Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) - Methods of test and general requirements |
| BS EN 14598-3-2005 | 增强热固性模塑化合物.模压塑料板材(SMC)和模塑料块(BMC)的规范.特殊要求 | Reinforced thermosetting moulding compounds - Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) - Specific requirements |
| BS EN 14758-1-2005+A1-2009 | 无压力地下排水和污水用塑料管道系统.含矿物调节剂的聚丙烯(PP-MD).管、配件和系统用规范. | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1:Specifications for pipes, fittings and the system |
| BS EN 14802-2005 | 塑料管道系统.检验室和人孔用热塑性升降井或升降机.耐路表面和交通载荷的测定 | Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading |
| BS EN 14867-2005 | 包装.塑料冰冻袋.规范和试验方法 | Packaging — Plastic freezer bags — Specifications and test methods |
| BS EN 14882-2005 | 橡胶或塑料涂层织物.静摩擦和动摩擦系数的测定 | Rubber or plastic coated fabrics - Determination of the static and dynamic coefficient of friction |
| BS EN 14886-2008 | 橡胶和塑料机械.块状塑料泡沫用带刀切削机.安全要求 | Plastics and rubber machines - Bandknife cutting machines for block foams - Safety requirements |
| BS EN 14909-2006 | 防水挠性薄板.塑料和橡胶防潮层.定义和特性 | Flexible sheets for waterproofing - Plastic and rubber damp proof courses - Definitions and characteristics |
| BS EN 14932-2006 | 塑料.包装袋用伸缩热塑性薄膜.要求和试验方法 | Plastics — Stretch thermoplastic films for wrapping bales - Requirements and test methods |
| BS EN 14963-2006 | 屋顶覆盖物.带或不带竖立支架的连续塑料天窗.分级、要求和试验方法 | Roof coverings - Continuous rooflights of plastics with or without upstands - Classification, requirements and test methods |
| BS EN 14979-2006 | 包装.柔性塑料/金属叠层管.S13型喷嘴的尺寸公差 | Packaging - Flexible plastic/metal laminate tubes - Dimensions and tolerances of nozzle S 13 |
| BS EN 14982-2006 | 塑料管道系统.监测室和人孔用热塑柄和提升设备.环硬挺度的测定 | Plastics piping and ducting systems — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of ring stiffness |
| BS EN 14987-2006 | 塑料.评估废水处理场生物降解能力.最终验收和规范试验计划 | Plastics - Evaluation of disposability in waste water treatment plants - Test scheme for final acceptance and specifications |
| BS EN 14995-2006 | 塑料.降解塑料可堆肥性的评估.试验方案和规范 | Plastics - Evaluation of compostability - Test scheme and specifications |
| BS EN 15012-2007 | 塑料管道系统.建筑结构内部的粪便和废弃物排放系统.管道、配件及其连接件的性能特性 | Plastics piping systems - Soil and waste discharge systems within the building structure - Performance characteristics for pipes, fittings and their joints |
| BS EN 15014-2007 | 塑料管道系统.压力下水和其它液体用地下埋设和地上铺设系统.管道、配件及其连接件的性能特点 | Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints |
| BS EN 15015-2007 | 塑料管系统.非人类消耗用冷热水系统.管、配件及其连接件的性能特点 | Plastics piping systems - Systems for hot and cold water not intended for human consumption - Performance characteristics for pipes, fittings and their joints |
| BS EN 15067-2007 | 塑料和橡胶机械.袋子用薄膜吹炉冶炼机.安全要求 | Plastics and rubber machines - Film converting machines for bags and sacks - Safety requirements |
| BS EN 1519-1-2000 | 建筑物结构内粪水和废水排出(低和高温)用塑料管道系统.聚乙烯(PE).管道,配件和系统规范 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Specifications for pipes, fittings and the system |
| BS EN 15284-2007 | 与食品料接触的材料和物品.陶瓷、玻璃、玻璃陶瓷或塑料炊具的微波加热耐力的试验方法 | Materials and articles in contact with food stuffs - Test method for the resistance to microwave heating of ceramic, glass, glass-ceramic or plastic cookware |
| BS EN 15342-2007 | 塑料.再生塑料.聚苯乙烯(PS)回收再生材料的特性 | Plastics - Recycled plastics - Characterization of polystyrene (PS) recyclates |
| BS EN 15343-2007 | 塑料.再生塑料.塑料再生可追溯性和一致性与再生内容的评估 | Plastics - Recycled plastics - Plastics recycling traceability and assessment of conformity and recycled content |
| BS EN 15344-2007 | 塑料.再生塑料.聚乙烯(PE)回收再生物的特性 | Plastics - Recycled plastics - Characterization of polyethylene (PE) recyclates |
| BS EN 15345-2007 | 塑料.再生塑料.聚丙烯(PP)回收再生物的特性 | Plastics - Recycled plastics - Characterization of polypropylene (PP) recyclates |
| BS EN 15346-2007 | 塑料.再生塑料.聚氯乙烯(PVC)回收再生物的特性 | Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates |
| BS EN 15347-2007 | 塑料.再生塑料.塑料废弃物的特性 | Plastics - Recycled Plastics - Characterization of plastics waste |
| BS EN 15348-2007 | 塑料.再生塑料.聚对苯二甲酸乙二酯(PET)回收再生物的特性 | Plastics - Recycled plastics - Characterization of poly(ethylene terephthalate) (PET) recyclates |
| BS EN 15386-2007 | 包装.柔性叠层板和塑料管.测定印刷附着力的试验方法 | Packaging - Flexible laminate and plastic tubes - Test method to determine the print adhesion |
| BS EN 15416-2-2007 | 苯酚和氨基塑料除外的负荷轴承木结构用粘结剂.试验方法.第2部分:压缩剪切中多重粘结样品的静载荷试验 | Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 2: Static load test of multiplebondline specimens in compressionshear |
| BS EN 15416-5-2006 | 苯酚和氨基塑料除外的负荷轴承木结构的粘结剂.试验方法.常规加压时间测定 | Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of conventional pressing time |
| BS EN 1548-2007 | 防水柔性薄板材.屋顶防水用塑料和橡胶薄板材.暴露于沥青中的方法 | Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Method for exposure to bitumen |
| BS EN 1555-1-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).总则 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - General |
| BS EN 1555-2-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).管道 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Pipes |
| BS EN 1555-3-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).配件 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Fittings |
| BS EN 1555-4-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).阀门 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Valves |
| BS EN 1555-5-2004 | 供应气体燃料用塑料管道系统.聚乙烯(PE).系统的适用性 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Fitness for the purpose of the system |
| BS EN 15619-2008 | 橡胶或塑料涂覆织物.临时建筑物(帐篷)的安全性.帐篷和相关建筑物用涂层织物的规范 | Rubber or plastic coated fabrics - Safety of temporary structures(tents) - Specification for coated fabrics intended for tents andrelated structures |
| BS EN 1565-1-2000 | 建筑物结构内粪水和废水排放(低和高温)用塑料管道系统.苯乙烯共聚物混合物(SAN+PVC).管道,配件和系统规范 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN + PVC) - Specifications for pipes, fittings and the system |
| BS EN 1566-1-2000 | 建筑物结构内的污物和废水(低和高温)排放用塑料管道系统.氯化聚偏二氯乙烯(PVC-C).管道,配件和系统规范 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Specification for pipes, fittings and the system |
| BS EN 15702-2008 | 泡沫塑料.软质和硬质聚氨酯泡沫孔计数程序 | Cellular plastics - Cell count procedure for flexible and rigid polyurethane |
| BS EN 1612-2-2000+A1-2008 | 塑料和橡胶机.反应模塑机.反应模塑设备用安全要求 | Plastics and rubber machines - Reaction moulding machines - Safety requirements for reaction moulding plant |
| BS EN 1638-1997 | 塑料管道系统.玻璃增强的热固塑料管道(GRP).柱状内压效果的试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method for the effects of cyclic internal pressure |
| BS EN 1680-1997 | 塑料软管系统.聚乙烯(PE)管道系统用的阀门.弯曲力施加在工作机构上和之后的密封性的检验方法 | Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanism |
| BS EN 1704-1997 | 塑料管道系统.热塑料管阀.弯曲情况下温度循环后阀门完整性的试验方法 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after temperature cycling under bending |
| BS EN 1705-1997 | 塑料管道系统.热塑性阀门.经过外部冲击后阀门的完整性试验方法 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow |
| BS EN 1716-1997 | 塑料管道系统.聚乙烯(PE)开孔三通件.安装好的开孔三通上抗冲击应力检测方法 | Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an assembled tapping tee |
| BS EN 1734-1997 | 橡胶或塑料涂覆织物.耐水渗透性测定.低压法 | Rubber- or plastics- coated fabrics - Determination of resistance to water penetration - Low-pressure method |
| BS EN 1735-1997 | 橡胶或塑料涂覆织物.挠曲性测定 | Rubber- or plastics- coated fabrics - Determination of flexibility |
| BS EN 1796-2006+A1-2008 | 有或无压力供水塑料管道系统.基于不饱和聚酯树脂(UP)的玻璃增强热固塑料(GRP) | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) |
| BS EN 1842-1997 | 塑料.热固性聚合物(SMC-BMC).压制模缩测定 | Plastics - Thermoset moulding compounds (SMC-BMC) - Determination of compression moulding shrinkage |
| BS EN 1844-2001 | 防水柔性板.耐臭氧性测定.屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing |
| BS EN 1847-2001 | 防水柔性层.防水塑料和橡胶薄板.暴露于包括水的液体化学药品的方法 | Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Methods for exposure to liquid chemicals including water |
| BS EN 1848-2-2001 | 防水柔性板.长度、宽度和平直度的测定.屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of length, width and straightness - Plastic and rubber sheets for roof waterproofing |
| BS EN 1849-2-2001 | 防水柔性板.厚度和单位面积质量的测定.屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Plastic and rubber sheets for roof waterproofing |
| BS EN 1850-2-2001 | 防水柔性板.可视缺陷的测定.屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of visible defects - Plastic and rubber sheets for roof waterproofing |
| BS EN 1862-1998 | 塑料管道系统.玻璃增强热固性塑料管(GRP).暴露于化学环境后相关蠕变系数的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the relative flexural creep factor following exposure to a chemical environment |
| BS EN 1873-2005 | 屋顶用预制附件.塑料单个屋顶灯.产品规范和试验方法 | Prefabricated accessories for roofing - Individual roof lights of plastics - Product specification and test methods |
| BS EN 1875-3-1998 | 橡胶和塑料涂覆织物.撕裂强度测定.梯形法 | Rubber and plastics-coated fabrics - Determination of tear strength - Trapezoidal method |
| BS EN 1876-1-1998 | 橡胶或塑料涂层织物.低温试验.弯曲试验 | Rubber- or plastics-coated fabrics - Low temperature tests - Bending test |
| BS EN 1876-2-1998 | 橡胶或塑料涂覆织物.低温试验.环形冲击试验 | Rubber- or plastics-coated fabrics - Low temperature tests - Impact test on loop |
| BS EN 1903-2008 | 胶粘剂.塑料或橡胶地板覆盖物或墙壁覆盖物用胶粘剂的试验方法.加速老化后尺寸变化的测定 | Adhesives - Test method for adhesives for plastic or rubber floor coverings or wall coverings - Determination of dimensional changes after accelerated ageing |
| BS EN 1905-1999 | 塑料管道系统.未增塑聚氯乙烯管、配件和材料.基于氯的总含量评估聚氯乙烯含量的方法 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on total chlorine content |
| BS EN 1928-2000 | 防水用挠性板.屋顶防水用沥青、塑料和橡胶薄板.水密性的测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of watertightness |
| BS EN 1931-2000 | 防水用挠性板.屋顶防水用沥青、塑料和橡胶薄板.水蒸气渗透性测量 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of water vapour transmission properties |
| BS EN 1979-1999 | 塑料管道和管道系统.热塑螺旋型结构壁的管道.接缝拉伸强度测定 | Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam |
| BS EN 233-1999 | 卷式壁纸.成品壁纸、乙烯基壁纸和塑料壁纸的规范 | Wallcoverings in roll form - Specification for finished wallpapers, wall vinyls and plastics wallcoverings |
| BS EN 2377-1989 | 玻璃纤维增强的塑料规范.试验方法.表面层间剪切强度测定 | Specification for glass fibre reinforced plastics - Test method - Determination of apparent interlaminar shear strength |
| BS EN 2378-1995 | 纤维增强的塑料.用浸泡法测定塑料吸水性 | Fibre reinforced plastics - Determination of water absorption by immersion |
| BS EN 2489-1995 | 纤维增强塑料.试验液体效应的测定 | Fibre reinforced plastics - Determination of the action of test fluids |
| BS EN 2561-1995 | 碳素纤维增强的塑料.无向的塑料层压制品.平行与纤维方向的抗拉试验 | Carbon fibre reinforced plastics - Undirectional laminates - Tensile test parallel to the fibre direction |
| BS EN 2562-1997 | 碳素纤维增强塑料.单向层压塑料.与纤维方向平行的弯曲试验 | Carbon fibre reinforced plastics - Unidirectional laminates - Flexural test parallel to the fibre direction |
| BS EN 2563-1997 | 碳纤维增强塑料.单向层压板.层间表面剪切强度的测定 | Carbon fibre reinforced plastics - Unidirectional laminates - Determination of the apparent interlaminar shear strength |
| BS EN 25978-1993 | 橡胶或塑料涂覆织物.耐粘结性测定 | Rubber- or plastics-coated fabrics - Determination of blocking resistance |
| BS EN 26590-2-1993 | 包装袋.第2部分:术语和类型.热塑性塑料软薄膜袋 | Packaging - Sacks - Vocabulary and types - Sacks made from thermoplastic flexible film |
| BS EN 26591-2-1993 | 包装袋.第2部分:测量方法和说明.热塑性塑料软薄膜空袋 | Packaging - Sacks - Description and method of measurement - Empty sacks made from thermoplastic flexible film |
| BS EN 26801-1985 | 橡胶或塑料软管.体积膨胀的测定 | Rubber or plastics hoses - Determination of volumetric expansion |
| BS EN 2743-2002 | 航空航天系列.纤维增强的塑料.未老化材料测试前状态调节的标准程序 | Aerospace series - Fibre reinforced plastics - Standard procedures for conditioning prior to testing unaged materials |
| BS EN 2746-1998 | 玻璃纤维增强塑料.弯曲试验.三点弯曲法 | Glass fibre reinforced plastics - Flexural test - Three point bend method |
| BS EN 2747-1998 | 玻璃纤维增强塑料.拉伸试验 | Glass fibre reinforced plastics - Tensile test |
| BS EN 28029-1987 | 塑料软管.织物增强的通用可拆卸水管规范 | Plastics hose - General purpose collapsible water hose, textile reinforced - Specification |
| BS EN 28233-1992 | 热塑性塑料阀门的扭矩试验方法 | Thermoplastics valves - Torque - Test method |
| BS EN 28659-1992 | 热塑性塑料阀门.疲劳强度.试验方法 | Thermoplastics valves - Fatigue strength - Test method |
| BS EN 289-2004+A1-2008 | 塑料机和橡胶机.压力.安全要求 | Plastics and rubber machines - Presses - Safety requirements |
| BS EN 3475-513-2005 | 航空器用电缆.试验方法.第513部分:耐变形(用塑料电缆扎带安装) | Cables, electrical, aircraft use - Test methods - Part 513: Deformation resistance (Installation with plastic cable ties) |
| BS EN 3545-001-2008 | 航空航天系列.工作温度为-55℃～175℃锁紧装置后部密封或非密封的、塑料壳体矩形电连接器.技术规范 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Technical specification |
| BS EN 3545-002-2008 | 航空航天系列.工作温度为-55℃～175℃后部密封和非密封塑料壳自锁紧装置的矩形电连接器.性能和触点排列规范 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 002: Specification of performanceand contact arrangements |
| BS EN 3545-003-2005 | 航空航天系列.工作温度-55℃至175℃后部密封或非密封的、塑料壳体矩形连接器.插孔接点的连接器.产品标准 | Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures - 55 ℃ to 175 ℃ — Part 003: Connectors with female contacts — Product standard |
| BS EN 3545-004-2005 | 工作温度为-55℃～175℃后部密封或非密封的、塑料壳体锁紧装置的矩形电连接器.第004部分:带插头触点的连接 | Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures - 55 ℃ to 175 ℃ - Part 004: Connectors with male contacts - Product standard |
| BS EN 3545-005-2006 | 航空航天系列.工作温度为-55℃～175℃后部密封或非密封的塑料壳锁紧装置的矩形电连接器.安装在无外壳(插塞) | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Male coding and attachment system for mounting on free housing (plug) - Product standard |
| BS EN 3545-006-2006 | 航空航天系列.工作温度为-55℃～175℃后部密封或非密封的塑料壳锁紧装置的矩形电连接器.安装在固定外壳(插 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Male coding and attachment system for fitment on fixed housing (receptacle) - Product standard |
| BS EN 3545-007-2005 | 工作温度为-55℃～175℃后部密封或非密封的、塑料壳体矩形电连接器.第007部分:产品标准 | Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures - 55 ℃ to 175 ℃ — Part 007: Cable clamp — Product standard |
| BS EN 3545-008-2006 | 航空航天系列.工作温度为-55℃～175℃后部密封或非密封的、塑料壳锁紧装置矩形电连接器.编码的装配/移除工 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Tools for assembly/removal of coding and attachment systems - Product standard |
| BS EN 3545-009-2008 | 航空航天系列.工作温度为-55℃～175℃带有后部密封和非密封的塑料壳锁紧装置的矩形电连接器.插头和插座用保 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 009: Protective cover for plugand receptacle — Product standard |
| BS EN 495-5-2001 | 防水挠性板.低温时测定可折叠性.屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of foldability at low temperature - Plastic and rubber sheets for roof waterproofing |
| BS EN 579-1994 | 塑料管道系统.交联聚乙烯(PE-X)管.用溶剂萃取法测定交联密度 | Plastics piping systems - Crosslinked polyethylene (PE-X) pipes - Determination of degree of crosslinking by solvent extraction |
| BS EN 580-2003 | 塑料管道系统.未增塑聚氯乙烯(PVC-U)管.特定温度下耐二氯甲烷的试验方法 | Plastics piping Systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test methods for the resistance to dichloromethane at a specified temperature (DCMT) |
| BS EN 60264-2-2-1992 | 绕组线的封装.圆桶装交货线盘.热塑塑料制可回收线盘规范 | Packaging of winding wires - Cylindrical barrelled delivery spools - Specification for returnable spools made from thermoplastic material |
| BS EN 60264-2-3-1992 | 绕组线的封装.第2部分:圆桶形输出线轴.第3节:由热塑性塑料制成的不能重复使用的绕线轴规范 | Packaging of winding wires - Cylindrical barrelled delivery spools - Specification for non-returnable spools made from thermoplastic material |
| BS EN 60264-3-3-1992 | 绕组线的封装.圆桶装交货线盘.热塑塑料制不可回收线盘规范 | Packaging of winding wires - Taper barrelled delivery spools - Specification for non-returnable spools made from thermoplastic material |
| BS EN 60264-4-1-1992 | 绕组线的封装.第4部分:试验方法.第1节:热塑性塑料制成的输出线轴 | Packaging of winding wires - Methods of test - Delivery spools made from thermoplastic material |
| BS EN 60264-4-2-1995 | 绕组线封装.第4部分:试验方法.第2节:热固塑料制锥形筒式供带盘容器 | Packaging of winding wires- Part 4-2: Methods of test - Containers made from thermoplastic material for taper barrelled delivery spools |
| BS EN 60454-3-2-2006 | 电气用压敏胶带.单项材料规范.带有橡胶热固胶、橡胶热塑性塑料或丙烯酸交联胶的聚酯薄膜胶粘带用要求 | Pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Requirements for polyester film tapes with rubber thermosetting, rubber thermoplastic or acrylic crosslinked adhesives |
| BS EN 60674-1-1990 | 电气用塑料薄膜规范.定义和一般要求 | Specification for plastic films for electrical purposes - Definitions and general requirements |
| BS EN 60674-2-1990 | 电气用塑料薄膜规格.试验方法 | Specification for plastic films for electrical purposes - Methods of test |
| BS EN 60674-3-1-1998 | 电气用塑料薄膜规范.单项材料规范.电容器用双轴定向聚丙烯薄膜 | Specification for plastic films for electrical purposes - Specifications for individual materials - Biaxially oriented polypropylene (PP) films for capacitors |
| BS EN 60674-3-2-1995 | 电气用塑料薄膜规范.各型材料规范.电气绝缘用平衡双取向聚对苯二甲酸乙酯薄膜要求 | Specification for plastic films for electrical purposes - Specifications for individual materials - Requirements for balanced biaxially oriented polyethylene terephthalate (PET) films used for electrical insulation |
| BS EN 60674-3-3-1995 | 电气用塑料薄膜范格.专用材料的规范.电气绝缘用聚碳酸酯薄膜要求 | Specification for plastic films for electrical purposes - Specifications for individual materials - Requirements for polycarbonate (PC) films used for electrical insulation |
| BS EN 60674-3-4 to 6-1995 | 电工用塑料薄膜规范.各型材料规范.电绝缘用聚酰亚胺薄膜要求 | Specification for plastic films for electrical purposes - Specifications for individual materials - Requirements for polyimide films used for electrical insulation |
| BS EN 60674-3-7-1995 | 电气用塑料薄膜规格.专用材料的规格.电气绝缘用氟乙烯-丙烯薄膜的要求 | Specification for plastic films for electrical purposes - Specifications for individual materials - Requirements for fluoroethylene-propylene (FEP) films used for electrical insulation |
| BS EN 60749-20-2009 | 半导体器件.机械和气候试验方法.塑料包封的SMDs的抗湿及钎焊热度综合影响 | Semiconductor devices - Mechanical and climatic test methods - Resistance of plastic encapsulated SMDs to the combined effect of moisture and soldering heat |
| BS EN 60749-31-2003 | 半导体器件.机械和气候试验方法.塑料包封器件的易燃性(内部感应) | Semiconductor devices - Mechanical and climatic test methods - Flammability of plastic-encapsulated devices (internally induced) |
| BS EN 60749-32-2003 | 半导体器件.机械和气候试验方法.塑料包封器件的易燃性(外部感应) | Semiconductor devices - Mechanical and climatic test methods - Flammability of plastic-encapsulated devices (externally induced) |
| BS EN 61234-1-1994 | 电绝缘材料水解稳定性的试验方法.第1部分:塑料薄膜 | Method of test for hydrolytic stability of electrical insulating materials - Method of test for hydrolytic stability of electrical insulating materials - Plastic films |
| BS EN 61754-21-2005 | 纤维光学连接器接口.塑料光纤的SMI型连接器门类 | Fibre optic connector interfaces - Type SMI connector family for plastic optical fibre |
| BS EN 62148-4-2004 | 纤维光学有源元件和器件.包装和接口标准.PN 1x9塑料光纤无线电收发信机 | Fibre optic active components and devices - Package and interface standards - PN 1x9 plastic optical fibre transceivers |
| BS EN 62300-2005 | 带塑料光纤的用户音频/视频设备数字接口 | Consumer audio/video equipment digital interface with plastic optical fibre |
| BS EN 637-1995 | 塑料管道系统.玻璃纤维增强塑料部件.用重量法测定组分量 | Plastics piping systems - Glass-reinforced plastics components - Determination of the amounts of constituents using the gravimetric method |
| BS EN 705-1995 | 塑料管道系统.玻璃增强热固性(GRP)塑料管和配件.回归分析及其使用方法 | Plastics piping systems - Glass-reinforced thermosetting (GRP) pipes and fittings - Methods for regression analyses and their use |
| BS EN 713-1995 | 塑料管道系统.管件和聚烯烃压力管的机械连接.组件承受弯曲作用时内部压力密封性的试验方法 | Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending |
| BS EN 727-1995 | 塑料管道和管道系统.热塑性塑料管和配件.维卡(vicat)软化温度的测定 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
| BS EN 728-1997 | 塑料管和管道系统.聚烯烃管和配件.氧化诱导时间的测定 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| BS EN 744-1996 | 塑料管道和导管系统.热塑管.抗日夜外部连续冲击应力的试验方法 | Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method |
| BS EN 761-1995 | 塑料管道系统.玻璃纤维增强热固性塑料管.干燥条件下蠕变系数的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under dry conditions |
| BS EN 802-1995 | 塑料管和管道系统.压力管道系统的注射铸造热塑性部件.最大挤压变形试验方法 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for pressure piping systems - Test method for maximum deformation by crushing |
| BS EN 803-1995 | 塑料管道系统.压力管道的弹性密封圈式连接件用注模制热塑塑料性配件.耐无部端推力的快速内压的试验方法 | Plastics piping systems - Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust |
| BS EN 804-1995 | 塑料管道系统.压力管道溶剂胶粘接头的注射模塑承口连接管件.短期内部液压压力的试验方法 | Plastics piping systems - Injection-moulded socket fittings for solvent-cemented joints for pressure piping - Test method for resistance to a short-term internal hydrostatic pressure |
| BS EN 852-1-1996 | 用于输送人用水的塑料管道系统.游动性评定.游动值的确定 | Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes |
| BS EN 855-1997 | 塑料软管和软管组件.热塑料纺织物增强的液压用类型.规范 | Plastics hoses and hose assemblies - Thermoplastics textile reinforced hydraulic type - Specification |
| BS EN 911-1996 | 塑料管道系统.热塑塑料压力管道用的弹性密封环型接头和机械接头.外部流体静压条件下防漏密封试验方法 | Plastics piping systems - Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - Test method for leaktightness under external hydrostatic pressure |
| BS EN 917-1997 | 塑料管道系统.热塑阀门.抗内压和泄漏密封性的试验方法 | Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal pressure and leaktightness |
| BS EN 922-1995 | 塑料管和管道系统.未增塑聚氯乙烯管道和配件.粘度系数测定和K值计算的样品准备 | Plastics piping and ducting systems - Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) - Specimen preparation for determination of the viscosity number and calculation of the k-value |
| BS EN 976-1-1997 | 玻璃增强塑料地下油罐.非压力存储液体石油基燃料的卧式园柱油罐.单壁油罐试验方法和要求 | Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Requirements and test methods for single wall tanks |
| BS EN 976-2-1997 | 玻璃增强塑料地下油罐.非压力存储液体石油基燃料的卧式园柱油罐.单壁油罐的运输,储存,搬运和安装 | Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Transport, handling, storage and installation of single wall tanks |
| BS EN 977-1998 | 玻璃增强塑料地下水箱(GRP).单侧液流法 | Underground tanks of glass-reinforced plastics (GRP) - Method for one side exposure to fluids |
| BS EN 978-1997 | 玻璃纤维增强塑料地下水箱.ALPHA因子和β因子的测定 | Underground tanks of glass-reinforced plastics (GRP) - Determination of factor and factor |
| BS EN ISO 10082-2000 | 塑料.酚醛树脂.分类和试验方法 | Plastics - Phenolic resins - Classification and test methods |
| BS EN ISO 10093-1999 | 塑料.燃烧试验.标准点火源 | Plastics - Fire tests - Standard ignition sources |
| BS EN ISO 10350-1-2008 | 塑料.可比较单点数据的采集和表示.模塑材料 | Plastics - Acquisition and presentation of comparable singlepointdata - Part 1: Moulding materials |
| BS EN ISO 10350-2-2001 | 塑料.可比单点数据的采集和表示法.第2部分:长纤维增强塑料 | Plastics - Acquisition and presentation of comparable single-point data - Long-fibre-reinforced plastic |
| BS EN ISO 10352-1997 | 纤维增强塑料.模塑化合物和预浸料坯.单位面积质量的测定 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass per unit area |
| BS EN ISO 10366-1-2002 | 塑料.甲基丙烯酸甲酯/丁二烯/苯乙烯共聚物(ABS)的模塑和压塑材料.命名和符号系统和规范的基础知识 | Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 10366-2-2004 | 塑料.甲基丙烯酸甲酯/丙烯腈/丁二烯/苯乙烯模塑和挤塑材料.试样制备和性能测定 | Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 1043-1-2002 | 塑料.符号和缩略语.基本聚合物及其特性 | Plastics - Symbols and abbreviated terms - Basic polymers and their special characteristics |
| BS EN ISO 1043-3-1999 | 塑料.符号和缩略语.增塑剂 | Plastics - Symbols and abbreviated terms - Plasticizers |
| BS EN ISO 1043-4-1999 | 塑料.符号和缩略语.阻燃剂 | Plastics - Symbols and abbreviated terms - Flame retardants |
| BS EN ISO 1060-1-1999 | 塑料.氯乙烯的均聚物和共聚物树脂.标示体系和基础规范 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Designation system and basis for specifications |
| BS EN ISO 1060-2-1999 | 塑料.氯乙烯的均聚物和共聚物树脂.试样的制备和性能的测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Preparation of test samples and determination of properties |
| BS EN ISO 1061-1999 | 塑料.未增塑的醋酸纤维素.游离酸度的测定 | Plastics - Unplasticized cellulose acetate - Determination of free acidity |
| BS EN ISO 10724-1-2001 | 塑料.热固粉末模塑复合物试样的喷射模塑成型.一般原理和多用途试样的模塑成型 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - General principles and moulding of multipurpose test specimens |
| BS EN ISO 10724-2-2001 | 塑料.热固粉末模塑复合物试样的注射模塑成型.小板材 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Small plates |
| BS EN ISO 10931-2005 | 工业用塑料管道系统.聚偏氟乙烯(PVDF).组件和系统用规范 | Plastics piping systems for industrial applications - Poly(vinylidene fluoride) (PVDF) - Specifications for components and the system |
| BS EN ISO 10960-1997 | 橡胶和塑料软管.在动态条件下耐臭氧性的评定 | Rubber and plastic hoses - Assessment of ozone resistance under dynamic conditions |
| BS EN ISO 1110-1998 | 塑料.聚酰胺.试样的加速调节 | Plastics - Polyamides - Accelerated conditioning of test specimens |
| BS EN ISO 11248-2000 | 塑料.热固性模塑.高温下短期性能的评定 | Plastics - Thermosetting moulding materials - Evaluation of short-term performance at elevated temperatures |
| BS EN ISO 1133-2005 | 塑料.热塑性塑料熔体质量流速(MFR)和熔体体积流速(MVR)的测定 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| BS EN ISO 11337-2004 | 塑料.聚酰胺.用气相色谱法测定e-己内酰胺和w-laurolactum | Plastics - Polyamides - Determination of e-caprolactam and w-laurolactum by gas chromatography |
| BS EN ISO 11357-1-2009 | 塑料.示差扫描量热法(DSC).一般原理 | Plastics - Differential scanning calorimetry (DSC) - General principles |
| BS EN ISO 11358-1997 | 塑料.聚合物的热重分析法(TG).一般原理 | Plastics - Thermogravimetry (TG) of polymers - General principles |
| BS EN ISO 11401-1998 | 塑料.酚醛树脂.用液体色谱法分离 | Plastics - Phenolic resins - Separation by liquid chromatography |
| BS EN ISO 11403-1-2003 | 塑料.可比较多点数据的采集和表示.机械性能 | Plastics - Acquisition and presentation of comparable multipoint data - Mechanical properties |
| BS EN ISO 11403-2-2004 | 塑料.可比多点数据的采集和表示.第2部分:热性能和加工性能 | Plastics - Acquisition and presentation of comparable multipoint data - Thermal and processing properties |
| BS EN ISO 11403-3-2001 | 塑料.可比多点数据的获取和表示.对特性的环境影响 | Plastics - Acquisition and presentation of comparable multipoint data - Environmental influences on properties |
| BS EN ISO 11409-1998 | 塑料.酚醛树脂.差示扫描量热法测定反应热和反应温度 | Plastics - Phenolic resins - Determination of heats and temperatures of reaction by differential scanning calorimetry |
| BS EN ISO 11468-2000 | 塑料.试验用PVC糊料的制备.溶解方法 | Plastics - Preparation of PVC pastes for test purposes - Dissolver method |
| BS EN ISO 11469-2000 | 塑料.塑料产品的通用识别方法和标记 | Plastics - Generic identification and marking of plastics products |
| BS EN ISO 11501-1996 | 塑料.薄膜和薄板.受热时尺寸变化的测定.薄膜和薄板受热时尺寸变化的测定 | Plastics - Film and sheeting - Determination of dimensional change on heating - Determination of dimensional change on heating of film and sheeting |
| BS EN ISO 11502-1996 | 塑料.薄膜和薄板.粘合阻力测定 | Plastics - Film and sheeting - Determination of blocking resistance |
| BS EN ISO 11542-1-2001 | 塑料.超高分子量聚乙烯模塑和挤塑材料.名称与符号系统和基本规范 | Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 11542-2-1999 | 塑料.超高分子量聚乙烯模塑和挤出材料.试样的制备和性能测定 | Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 1158-1998 | 塑料.氯乙烯均聚物和共聚物.氯含量的测定 | Plastics - Vinyl chloride homopolymers and copolymers - Determination of chlorine content |
| BS EN ISO 1163-1-2000 | 塑料.未增塑聚氯乙烯模制和挤制材料.名称与符号系统及基本规范 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 1163-2-2000 | 塑料.未增塑聚氯乙烯(PVC-U)模塑和挤塑材料.试样制备和性能测定 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 11667-2000 | 纤维增强塑料.模压化合物和聚酯胶片.树脂、增强的纤维和矿物填料含量的测定.溶解方法 | Fibre reinforced plastics - Moulding compounds and prepregs - Determination of resin, reinforcement-fibre and mineral-filler content - Dissolution methods |
| BS EN ISO 1167-3-2007 | 液体输送用热塑性塑料管、配件和组件.抗内压的测定.组件的制备 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Preparation of components |
| BS EN ISO 1167-4-2008 | 液体输送用热塑性塑料管、配件和组件.抗内压的测定.组件的制备 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Preparation of assemblies |
| BS EN ISO 1172-1999 | 纺织玻璃纤维增强塑料.聚酯胶片,模制混合物和叠层材料.纺织玻璃纤维和矿物添充物含量的测定.煅烧法 | Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content - Calcination methods |
| BS EN ISO 11758-1996 | 橡胶和塑料软管.氙弧灯下照射.颜色和外观变化的测定 | Rubber and plastics hoses - Exposure to a xenon arc lamp - Determination of changes in colour and appearance |
| BS EN ISO 1183-1-2004 | 塑料.非泡沫塑料的密度测定方法.浸渍法、液体比重瓶法和滴定法 | Plastics - Methods for determining the density of non-cellular plastics - Immersion method, liquid pyknometer method and titration method |
| BS EN ISO 1183-2-2004 | 塑料.非泡沫塑料的密度测定方法.密度梯度管法 | Plastics - Methods for determining the density of non-cellular plastics - Density gradient column method |
| BS EN ISO 1183-3-1999 | 塑料.非泡沫塑料密度测定方法.气体比重瓶测量法 | Plastics - Methods for determining the density of non-cellular plastics - Gas pyknometer method |
| BS EN ISO 11833-1-2007 | 塑料.未塑性聚氯乙烯板材.型号、尺寸和特点.厚度不低于1mm的板材 | Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Sheets of thickness not less than 1 mm |
| BS EN ISO 11833-2-1998 | 塑料.未增塑聚氯乙烯薄板.类型、尺寸和特征.厚度低于1mm的薄板 | Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Sheets of thickness less than 1 mm |
| BS EN ISO 11897-2001 | 包装.热塑性塑料软薄膜袋.折边处的撕裂扩展试验 | Packaging - Sacks made from thermoplastic flexible film - Tear propagation on edge folds |
| BS EN ISO 119-1998 | 塑料.苯醛模塑件.游离酚的测定.碘量法 | Plastics - Phenol-formaldehyde mouldings - Determination of free phenols - Iodometric method |
| BS EN ISO 11963-1996 | 塑料.聚碳酸酯薄片材.类型、尺寸和特性 | Plastics - Polycarbonate sheets - Types, dimensions and characteristics |
| BS EN ISO 120-1998 | 塑料.苯酚-甲醛模塑料.游离氨和铵化合物的测定.比色法 | Plastics - Phenol-formaldehyde mouldings - Determination of free ammonia and ammonium compounds - Colorimetric comparison method |
| BS EN ISO 12017-1996 | 塑料.聚甲基丙烯酸甲酯双合板和三合板.试验方法 | Plastics - Poly(methyl methacrylate) double- and triple-skin sheets - Test methods |
| BS EN ISO 12058-1-2002 | 塑料.用落球粘度计测定粘度.斜管法 | Plastics - 12058-1:2002)Determination ofviscosity using afalling-ballviscometer -Part 1: Inclined-tube method |
| BS EN ISO 12086-1-2006 | 塑料.含氟聚合物分散体模塑和挤塑材料.命名系统和基本规范 | Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 12086-2-2006 | 塑料.含氟聚合物分散体模塑和挤塑材料.试样的制备和性能的测定 | Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 12114-1997 | 纤维增强塑料.热固性模塑化合物和聚酯胶片.固化特性的测定 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of cure characteristics |
| BS EN ISO 12115-1997 | 纤维增强塑料.热固性模塑化合物和聚酯胶片.流动性、熟化期和储存期限的测定 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of flowability, maturation and shelf life |
| BS EN ISO 1264-1997 | 塑料.氯乙烯的均聚物和共聚物树脂.水萃物的pH值测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of pH of aqueous extract |
| BS EN ISO 1265-2007 | 塑料.聚氯乙烯树脂.杂质和外来杂质数的测定 | Plastics - Poly(vinyl chloride) resins - Determination of number of impurities and foreign particles |
| BS EN ISO 1269-2006 | 塑料.氯乙烯均聚物和共聚物树脂.挥发性物质(包括水)的测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of volatile matter (including water) |
| BS EN ISO 13000-1-2006 | 塑料.聚四氟乙烯(PTFE)半成品.要求和名称与符号 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Requirements and designation |
| BS EN ISO 13000-2-2006 | 塑料.聚四氟乙烯(PTFE)半成品.试样的制备和性能测定 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Preparation of test specimens and determination of properties |
| BS EN ISO 1307-2008 | 橡胶和塑料软管.软管尺寸、最小和最大内径以及长软管切割公差 | Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses |
| BS EN ISO 13468-1-1997 | 塑料.透明材料光透射率总量的测定.单束光发射仪器 | Plastics - Determination of the total luminous transmittance of transparent materials - Single-beam instrument |
| BS EN ISO 13468-2-1999 | 塑料.透明材料光透射率总量的测定.双束光度计 | Plastics - Determination of the total luminous transmittance of transparent materials - Double-beam instrument |
| BS EN ISO 13477-2008 | 流体输送用热塑性塑料管.耐裂纹快速扩展性(RCP)的测定.小型稳态试验(S4试验) | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) |
| BS EN ISO 13478-2007 | 输送流体用热塑性塑料管.耐裂纹快速扩展性(RCP)的测定.全面试验(FST) | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) |
| BS EN ISO 13760-2000 | 流体输送用压力塑料管.Miner规则.累积损坏的计算方法 | Plastics pipes for the conveyance of fluids under pressure - Miner's rule - Calculation method for cumulative damage |
| BS EN ISO 13783-1998 | 塑料管道系统.硬聚氯乙烯(PVC-U)端部承受负荷的双承口连接件.密封和承受弯曲内压的试验方法 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints - Test method for leaktightness and strength while subjected to bending and internal pressure |
| BS EN ISO 13802-1999 | 塑料.摆锤冲击鉴定.试验机.却贝、艾卓德和拉伸冲击.试验 | Plastics - Verification of pendulum impact-testing machines - Charpy, Izod and tensile impact-testing |
| BS EN ISO 13844-2000 | 塑料管道系统.与未增塑聚氯乙烯管一起使用的未增塑聚氯乙烯弹性密封环式套筒接头.负压下的密封性试验方法 | Plastics piping systems - Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure |
| BS EN ISO 13845-2000 | 塑料管道系统.与未增塑聚氯乙烯管一起使用的弹性密封环式套筒接头.内压下角度偏转密封试验 | Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with angular deflection |
| BS EN ISO 13846-2001 | 塑料管道系统.热塑性压力管用端负载和无端负载支承组件和接头.内部水压下长期密封性的试验方法 | Plastics piping systems - End-load-bearing and non-end-load bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaktightness under internal water pressure |
| BS EN ISO 13927-2001 | 塑料.用锥形辐射加热器和热电堆探测器进行简单热释放试验 | Plastics - Simple heat release test using a conical radiant heater and a thermopile detector |
| BS EN ISO 1402-2009 | 橡胶和塑料软管及软管组件.液压静力试验 | Rubber and plastics hoses and hose assemblies - Hydrostatic testing |
| BS EN ISO 14113-2008 | 气焊设备.压力小于450bar(45MPa)的工业气体用橡胶和塑料软管和软管组件 | Gas welding equipment - Rubber and plastics hose and hoseassemblies for use with industrial gases up to 450 bar (45 MPa) |
| BS EN ISO 14125-1998 | 纤维增强塑料复合材料.挠性性能的测定 | Fibre-reinforced plastic composites - Determination of flexural properties |
| BS EN ISO 14126-1999 | 纤维增强塑料复合材料.平面方向压缩性的测定 | Fibre-reinforced plastic composites - Determination of compressive properties in the in-plane direction |
| BS EN ISO 14129-1998 | 纤维增强塑料复合材料.用<+或->45°张力试验法测定平面剪切应力/剪切应变反应，包括平面剪切量和剪切强度 | Fibre-reinforced plastic composites - Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength by the <+OR-> 45 ° tension test method |
| BS EN ISO 14130-1998 | 纤维增强塑料复合材料.用短试片测定表观层间粘合剪切强度 | Fibre-reinforced plastic composites - Determination of apparent interlaminar shear strength by short-beam method |
| BS EN ISO 1421-1998 | 橡胶或塑料涂层织物.拉伸强度和断裂伸长率的测定 | Rubber-or plastics-coated fabrics - Determination of tensile strength and elongation at break |
| BS EN ISO 14233-2003 | 牙科学.聚合物基模塑料 | Dentistry - Polymer-based die materials |
| BS EN ISO 1452-1-2009 | 供水和地下及地上压力排水和污水用塑料管道系统.未增塑聚氯乙烯(PVC U).总则 | Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC U) - General |
| BS EN ISO 14526-1-2000 | 塑料.酚醛粉末模塑化合物(PF-PMCs).命名体系和基本规范 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Designation system and basis for specifications |
| BS EN ISO 14526-2-2000 | 塑料.酚醛粉末模塑化合物(PF-PMCs).试样的制备和特性测定 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Preparation of test specimens and determination of properties |
| BS EN ISO 14526-3-2000 | 塑料.酚醛粉末模塑化合物(PF-PMCs).对所选模塑化合物的要求 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Requirements for selected moulding compounds |
| BS EN ISO 14527-1-2000 | 塑料.脲醛和脲/蜜胺酚醛粉末模塑化合物(UF-和UF/MF-PMCs).命名体系和基本规范 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Designation system and basis for specifications |
| BS EN ISO 14527-3-2000 | 塑料.脲醛和脲/蜜胺酚醛粉末模塑化合物(UF-和UF/MF-PMCs).对所选模塑化合物的要求 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Requirements for selected moulding compounds |
| BS EN ISO 14528-1-2000 | 塑料.蜜胺酚醛粉末模塑化合物(MF-PMCs).命名体系和基本规范 | Plastics - Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Designation system and basis for specifications |
| BS EN ISO 14528-2-2000 | 塑料.蜜胺酚醛粉末模塑化合物(MF-PMCs).试样制备和性能测定 | Plastics - Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Preparation of test specimens and determination of properties |
| BS EN ISO 14528-3-2000 | 塑料.蜜胺酚醛粉末模塑化合物(MF-PMCs).对选择的模塑化合物的要求 | Plastics - Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Requirements for selected moulding compounds |
| BS EN ISO 14529-1-2000 | 塑料.蜜胺酚醛粉末模塑化合物(MF-PMCs).命名体系和基本规范 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Designation system and basis for specifications |
| BS EN ISO 14529-2-2000 | 塑料.蜜胺/酚醛粉末模塑化合物(MP-PMCs).试样制备和特性测定 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Preparation of test specimens and determination of properties |
| BS EN ISO 14529-3-2000 | 塑料.蜜胺/酚醛粉末模塑化合物(MP-PMCs).对所选模塑化合物的要求 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Requirements for selected moulding compounds |
| BS EN ISO 14530-1-2000 | 塑料.不饱和聚酯粉末模塑化合物(UP-PMCs).命名体系和基本规范 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Designation system and basis for specifications |
| BS EN ISO 14530-2-2000 | 塑料.不饱和聚酯粉末模塑化合物(UP-PMCs).试样的制备和特性测定 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Preparation of test specimens and determination of properties |
| BS EN ISO 14530-3-2000 | 塑料.不饱和聚酯粉末模塑化合物(UP-PMCs).对所选模塑化合物的要求 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Requirements for selected moulding compounds |
| BS EN ISO 14557-2003 | 消防水龙带.橡胶和塑料抽吸软管和软管组件 | Fire-fighting hoses - Rubber and plastics suction hoses and hose assemblies |
| BS EN ISO 14616-1997 | 塑料.聚乙烯、乙烯共聚物及其混合物的热收缩薄膜.收缩应力的测定 | Plastics - Heatshrinkable films of polyethylene, ethylene copolymers and their mixtures - Determination of the shrinkage stress and contraction stress |
| BS EN ISO 14663-1-2002 | 塑料.乙烯/乙烯醇(EVOH)共聚物模塑和挤塑材料.命名系统和基本规范 | Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 14663-2-2002 | 塑料.乙烯/乙烯醇(EVOH)共聚物模塑和挤塑材料.试样的制备和性能测定 | Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 14692-1-2003 | 石油和天然气工业.玻璃纤维增强塑料(GRP)管道.词汇、符号、应用和材料 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Vocabulary, symbols, applications and materials |
| BS EN ISO 14692-2-2003 | 石油和天然气工业.玻璃纤维增强塑料(GRP)管道.合格评定和生产 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Qualification and manufacture |
| BS EN ISO 14692-3-2003 | 石油和天然气工业.玻璃纤维增强塑料(GRP)管道.系统设计 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - System design |
| BS EN ISO 14692-4-2003 | 石油和天然气工业.玻璃纤维增强塑料(GRP)管道.制造、安装和运行 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Fabrication, installation and operation |
| BS EN ISO 14851-1999 | 水介质中塑料材料的富氧菌生物降解性的测定.在一封闭呼吸器中测定需氧量的方法 | Determination of the ultimate aerobic biodegradability of plastic materials in an aqueous medium - Method by measuring the oxygen demand in a closed respirometer |
| BS EN ISO 14852-1999 | 水介质中塑料材料的富氧菌生物降解性的测定.二氧化碳增量分析方法 | Determination of the ultimate aerobic biodegradability of plastic materials in an aqueous medium - Method by analysis of evolved carbon dioxide |
| BS EN ISO 14855-1-2007 | 塑料材料在受控堆肥环境下最终需氧生物降解能力的测定.释放二氧化碳的分析方法.第1部分:通用方法 | Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions - Method by analysis of evolved carbon dioxide - General method |
| BS EN ISO 14890-2003 | 输送带.通用织物结构的橡胶或塑料包覆的输送带规范 | Conveyor belts - Specification for rubber or plastics covered conveyor belts of textile construction for general use |
| BS EN ISO 14910-1-1998 | 塑料.模塑和挤塑用热塑聚酯/酯和聚醚/酯弹性体.命名系统和基本规范 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Designation system and basis for specifications |
| BS EN ISO 14910-2-1998 | 塑料.模塑和挤塑用热塑聚酯/酯和聚醚/酯弹性体.试样的制备和性能的测定 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Preparation of test specimens and determination of properties |
| BS EN ISO 15013-2007 | 塑料.聚丙烯(PP)挤压薄板材.要求和试验方法 | Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods |
| BS EN ISO 15015-2007 | 塑料.冲击改良的丙烯腈-苯乙烯共聚物挤压片材(ABS、AEPDS和ASA).要求和试验方法 | Plastics - Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA) - Requirements and test methods |
| BS EN ISO 15023-1-2002 | 塑料.聚乙烯醇(PVAL)材料.规范用命名体系和规范基础 | Plastics - Poly(vinyl alcohol) (PVAL) materials - Designation system and basis for specifications |
| BS EN ISO 15023-2-2003 | 塑料.聚乙烯醇(PVAL)材料.性能测定 | Plastics - Poly(vinyl alcohol) (PVAL) materials - Determination of properties |
| BS EN ISO 15103-2-2007 | 塑料.聚苯醚(PPE)模制和挤压成型材料.试样制备和特性测定 | Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 15106-1-2005 | 塑料.薄膜和薄片.水蒸气传输率的测定.湿度探测传感器法 | Plastics - Film and sheeting - Determination of water vapour transmission rate - Humidity detection sensor method |
| BS EN ISO 15106-2-2005 | 塑料.薄膜和薄片.水蒸气传输率的测定.红外探测传感器法 | Plastics - Film and sheeting - Determination of water vapour transmission rate - Infrared detection sensor method |
| BS EN ISO 15106-3-2005 | 塑料.薄膜和薄片.水蒸气传输率的测定.电解探测传感器法 | Plastics - Film and sheeting - Determinaktion of water vapour transmission rate - Electrolytic detection sensor method |
| BS EN ISO 15252-1-2000 | 塑料.环氧树脂模塑化合物(EP-PMCs).命名系统和基本规范 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Designation system and basis for specifications |
| BS EN ISO 15252-2-2000 | 塑料.环氧树脂模塑化合物(EP-PMCs).试样制备和特性测定 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Preparation of test specimens and determination of properties |
| BS EN ISO 15252-3-2000 | 塑料.环氧粉末模塑化合物(EP-PMCs).第3部分:对所选择模塑化合物的要求 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Requirements for selected moulding compounds |
| BS EN ISO 15310-2000 | 增强式塑料制品.采用板扭法对面内剪切模量的测定 | Reinforced plastics - Determination of the in-plane shear modulus by the plate twist method |
| BS EN ISO 15493-2003 | 工业用塑料管道系统.丙烯腈-丁二烯-苯乙烯共聚物(ABS)、未增塑的聚氯乙烯(PVC-U)和氯化聚氯乙烯(PVC-C).元 | Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly (vinyl chloride) (PVC-U) and chlorinated poly (vinyl chloride) (PVC-C) - Specifications for components and the system - Metric series |
| BS EN ISO 15494-2003 | 工业用塑料管道系统.聚丁烯(PB)、聚乙烯(PE)和聚丙烯(PP).元件和系统的规范.米制系列 | Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the system - Metric series |
| BS EN ISO 15526-1-2004 | 塑料.聚酮模塑和挤制材料.命名系统和基本规范 | Plastics - Polyketone (PK) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 15526-2-2004 | 塑料.聚酮(PK)模塑和挤塑材料.试样的制备和性能的测定 | Plastics - Polyketone (PK) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 15791-1-2003 | 塑料.塑料产品用中等燃烧试验的研制和应用.通用指南 | Plastics - Development and use of intermediate-scale fire tests for plastics products - General guidance |
| BS EN ISO 15874-1-2004 | 冷热水装置用塑料管道系统.聚丙烯(PP).总则 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - General |
| BS EN ISO 15874-2-2004 | 冷热水装置用塑料管道系统.聚丙烯(PP).管 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Pipes |
| BS EN ISO 15874-3-2004 | 冷热水装置用塑料管道系统.聚丙烯(PP).配件 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Fittings |
| BS EN ISO 15874-5-2004 | 冷热水装置用塑料管道系统.聚丙烯(PP).系统的适用性 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Fitness for purpose of the system |
| BS EN ISO 15875-1-2004 | 冷热水装置用塑料管道系统.交联聚乙烯.总则 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - General |
| BS EN ISO 15875-2-2004 | 冷热水装置用塑料管道系统.交联聚乙烯.管道 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Pipes |
| BS EN ISO 15875-3-2004 | 冷热水装置用塑料管道系统.交联聚乙烯.配件 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Fittings |
| BS EN ISO 15875-5-2004 | 冷热水装置用塑料管道系统.交联聚乙烯.系统的适用性 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Fitness for purpose of the system |
| BS EN ISO 15876-1-2004 | 冷热水装置用塑料管道系统.聚丁烯.总则 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - General |
| BS EN ISO 15876-2-2004 | 冷热水装置用塑料管道系统.聚丁烯.管道 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Pipes |
| BS EN ISO 15876-3-2004 | 冷热水装置用塑料管道系统.聚丁烯.配件 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Fittings |
| BS EN ISO 15876-5-2004 | 冷热水装置用塑料管道系统.聚丁烯.系统的适用性 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Fitness for purpose of the system |
| BS EN ISO 15908-2003 | 热塑塑料管道系统用胶粘剂.胶粘剂热稳定性测定的试验方法 | Adhesives for thermoplastic piping systems - Test method for the determination of thermal stability of adhesives |
| BS EN ISO 1598-2000 | 塑料.乙酸纤维素.不可溶颗粒的测定 | Plastics - Cellulose acetate - Determination of insoluble particles |
| BS EN ISO 1599-1999 | 塑料.醋酸纤维素.模塑时粘度降低的测定 | Plastics - Cellulose acetate - Determination of viscosity loss on moulding |
| BS EN ISO 1600-1999 | 塑料.乙酸纤维素.利用热的不同周期测定模制样品中的光吸收量 | Plastics - Cellulose acetate - Determination of light absorption of moulded specimens produced using different periods of heating |
| BS EN ISO 16101-2004 | 包装.危险物品的运输包装.塑料可混用性检验 | Packaging - Transport packaging for dangerous goods - Plastics compatibility testing |
| BS EN ISO 16103-2006 | 包装.危险物品运输包装.再生塑料材料 | Packaging - Transport packages for dangerous goods - Recycled plastics material |
| BS EN ISO 1622-1-2000 | 塑料.聚苯乙烯(PS)模塑和挤塑材料.命名体系和基本规范 | Plastics - Polystrene (PS) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 1622-2-1999 | 塑料.聚苯乙烯(PS)模塑和挤塑材料.试样制备和性能测定 | Plastics - Polystrene (PS) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 1624-2002 | 塑料.氯乙烯均聚物和共聚物树脂.水滤筛析 | Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis in water |
| BS EN ISO 1628-2-2000 | 塑料.用毛细粘度计测定稀释溶液中聚合物的粘度值.聚氯乙烯树脂 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Poly(vinyl chloride) resins |
| BS EN ISO 1628-3-2004 | 塑料.用毛细管粘度计测定稀释溶液中聚合物的粘度.聚乙烯和聚丙烯 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Polyethylenes and polypropylenes |
| BS EN ISO 1675-1998 | 塑料.液态树脂.比重计法测定密度 | Plastics - Liquid resins - Determination of density by the pyknometer method |
| BS EN ISO 16871-2003 | 塑料管道系统.塑料管道和配件.直接(自然)风化法 | Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering |
| BS EN ISO 172-1998 | 塑料.酚醛模塑件.游离氨的检验 | Plastics - Phenol-formaldehyde mouldings - Detection of free ammonia |
| BS EN ISO 1746-2001 | 橡胶或塑料软管和管件.弯曲试验 | Rubber or plastics hoses and tubing - Bending tests |
| BS EN ISO 175-2001 | 塑料.浸入液体化学药品的影响测定的试验方法 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals |
| BS EN ISO 17556-2003 | 塑料.通过测量呼吸计中的需氧量或放出的二氧化碳量测定土壤中的最大需氧生物降解能力 | Plastics - Determination of the ultimate aerobic biodegradability in soil by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved |
| BS EN ISO 176-2005 | 塑料.增塑剂损耗的测定.活性碳法 | Plastics - Determination of loss of plasticizers - Activated carbon method |
| BS EN ISO 177-2000 | 塑料.增塑剂扩散的测定 | Plastics - Determination of migration of plasticizers |
| BS EN ISO 178-2003 | 塑料.弯曲性能测定 | Plastics - Determination of flexural properties |
| BS EN ISO 179-1-2001 | 塑料.摆式冲击强度测定.无仪表显示的冲击试验 | Plastics - Determination of Charpy impact properties - Non-instrumented impact test |
| BS EN ISO 179-2-1999 | 塑料.摆式冲击特性测定.仪器记录冲击试验 | Plastics - Determination of Charpy impact properties - Instrumented impact test |
| BS EN ISO 1797-2-1995 | 牙科旋转器械.柄.第2部分:塑料柄 | Dental rotary instruments - Shanks - Shanks made of plastics |
| BS EN ISO 180-2001 | 塑料.伊兆特(Izod)冲击强度测定 | Plastics - Determination of Izod impact strength |
| BS EN ISO 182-2-2000 | 塑料.化合物和氯乙烯共聚物、均聚物在高温中分解出氯化氢和其他酸性物的趋势测定.pH值法 | Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - pH method |
| BS EN ISO 182-3-2000 | 塑料.化合物和氯乙烯共聚物、均聚物在高温中分解出氯化氢和其他酸性物的趋势测定.电导测量法 | Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Conductometric method |
| BS EN ISO 182-3-2001 | 塑料.化合物和氯乙烯共聚物、均聚物在高温下分解出氯化氢和其他酸性物质的趋势测定.电导测量法 | Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Conductometric method |
| BS EN ISO 182-4-2001 | 塑料.化合物和氯乙烯共聚物、均聚物在高温下分解出氯化氢和其他酸性物质的趋势测定.电位测量法 | Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Potentiometric method |
| BS EN ISO 1872-2-2007 | 塑料.聚乙烯(PE)模塑和挤塑材料.试样制备和性能测定 | Plastics - Polyethylene (PE) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 1873-1-1995 | 塑料.聚丙烯模塑和挤出塑料.第1部分:标示方法和技术要求的依据 | Plastics - Polypropylene (PP) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 1873-2-2007 | 塑料.聚丙烯(PP)模塑和挤塑材料.试样制备和特性测定 | Plastics - Polypropylene (PP) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 1874-1-2001 | 塑料.聚酰胺模塑和挤出材料.名称 | Plastics - Polyamide (PA) moulding and extrusion materials - Designation |
| BS EN ISO 1874-2-2007 | 塑料.聚酰胺(PA)模塑和挤塑材料.试件制备和性能测定 | Plastics - Polyamide (PA) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 1923-1995 | 多孔塑料和橡胶.线性尺寸测量 | Cellular plastics and rubbers - Determination of linear dimensions |
| BS EN ISO 20200-2005 | 塑料.在实验室试验中模拟堆肥处理条件下测定塑料的分解度 | Plastics - Determination of the degree of disintegration of plastic materials under simulated composting conditions in a laboratory-scale test |
| BS EN ISO 2039-1-2003 | 塑料.硬度测定.压球法 | Plastics - Determination of hardness - Ball indentation method |
| BS EN ISO 2039-2-2000 | 塑料.硬度测定.洛氏硬度 | Determination of Rockwell hardness - Rockwell hardness - Rockwell hardness |
| BS EN ISO 20848-1-2008 | 包装.塑料桶.标称容量113.6 L～220 L的可拆盖(开盖)圆桶 | Packaging - Plastics drums - Part 1: Removable head (openhead) drums with a nominal capacity of 113,6 l to 220 l |
| BS EN ISO 20848-2-2008 | 包装.塑料桶.标称容量208.2 L～220 L的固定盖(密封盖)圆桶 | Packaging - Plastics drums - Part 2: Non-removable head (tighthead) drums with a nominal capacity of 208,2 l and 220 l |
| BS EN ISO 20848-3-2008 | 包装.塑料圆桶.标称容量113.6 L～220 L塑料圆桶的塞子/桶孔闭合系统 | Packaging - Plastics drums - Part 3: Plug/bung closure systemsfor plastics drums with a nominal capacity of 113,6 l to 220 l |
| BS EN ISO 2114-2000 | 塑料(聚酯树脂)、涂料和清漆(粘合剂).部分酸值和总酸值的测定 | Plastics (polyester resins) and paints and varnishes (binders) - Determination of partial acid value and total acid value |
| BS EN ISO 22088-1-2006 | 塑料.测定耐环境应力破裂性(ESC).通用指南 | Plastics - Determination of resistance to environmental stress cracking (ESC) - General guidance |
| BS EN ISO 22088-2-2006 | 塑料.测定耐环境应力破裂性(ESC).恒定拉伸负荷法 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Constant tensile load method |
| BS EN ISO 22088-3-2006 | 塑料.测定耐环境应力破裂性.弯曲带法 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Bent strip method |
| BS EN ISO 22088-4-2006 | 塑料.测定耐环境应力破裂性.弯曲带法 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Ball or pin impression method |
| BS EN ISO 2231-1992 | 橡胶或塑料涂覆织物.调节和测试用标准大气 | Rubber- or plastics-coated fabrics - Standard atmospheres for conditioning and testing |
| BS EN ISO 2286-1-1998 | 橡胶或塑料涂覆织物.卷料参数的测定.长度、宽度和净重的测定方法 | Rubber- or plastics-coated fabrics - Determination of roll characteristics - Methods for determination of length, width and net mass |
| BS EN ISO 2286-2-1998 | 橡胶或塑料涂覆织物.卷料参数的测定.涂料单位面积总质量、单位涂层面积的质量和基体单位面积质量的测定方法 | Rubber- or plastics-coated fabrics - Determination of roll characteristics - Methods for determination of total mass per unit area, mass per unit area of coating and mass per unit area of substrate |
| BS EN ISO 2286-3-1998 | 橡胶或塑料涂覆织物.卷材参数的测定.厚度的测定方法 | Rubber- or plastics-coated fabrics - Determination of roll characteristics - Method for determination of thickness |
| BS EN ISO 23667-2007 | 包装.危险货物的运输包装.硬质塑料和塑料合成的IBCs.兼容性测试 | Packaging - Transport packaging for dangerous goods - Rigid plastics and plastics composite IBCs - Compatibility testing |
| BS EN ISO 2411-2000 | 橡胶或塑料涂层织物.涂层粘合力的测定 | Rubber or plastics-coated fabrics - Determination of coating adhesion |
| BS EN ISO 2535-2002 | 塑料.未饱和的聚酯树脂.室温时的胶凝时间的测量 | Plastics - Unsaturated polyester resins - Measurement of gel time at ambient temperature |
| BS EN ISO 2554-1999 | 塑料.不饱和聚酯树脂.羟基值的测定 | Plastics - Unsaturated polyester resins - Determination of hydroxyl value |
| BS EN ISO 2555-2000 | 塑料.液态或象乳胶或分散体一样的树脂.用布洛克菲文德试验法测定视粘度 | Plastics - Resins in the liquid state or as emulsions or dispersions - Determination of apparent viscosity by the Brookfield Test method |
| BS EN ISO 2556-2001 | 塑料.在大气压力下薄膜和薄板的气体透过率的测定.测压法 | Plastics - Determination of the gas transmission rate of films and thin sheets under atmospheric pressure - Manometric method |
| BS EN ISO 2578-1993 | 塑料.长期暴露于热作用后时间和温度极限值的测定 | Plastics - Determination of the time-temperature limits after prolonged exposure to heat |
| BS EN ISO 2580-1-2002 | 塑料.丙烯腈-丁二烯-苯乙烯共聚物(ABS)的模塑和压塑材料.命名和符号系统和规范基础 | Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 2580-2-2004 | 塑料.丙烯腈-丁二烯-苯乙烯共聚物(ABS)的模塑和挤塑材料.试样制备和性能测定 | Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 2818-1996 | 塑料.试样的机加工制备 | Plastics - Preparation of test specimens by machining |
| BS EN ISO 28941-1-2008 | 塑料.聚苯醚(PPE)模制和挤压成型材料.命名体系和基本规范 | Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 2897-1-1999 | 塑料.耐冲击的聚苯乙烯(PS-1)的模塑和挤塑材料.名称和符号系统和规范基础 | Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 2897-2-2004 | 塑料.耐冲击聚苯乙烯(PS-I)模塑和挤塑材料.试样制备和性能测定 | Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 2898-1-2000 | 塑料.增塑聚氯乙烯(PVC-P)注模和挤压材料.标识系统和规范基础 | Plastics - Plasticized poly (vinyl chloride) (PVC-P) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 2898-2-2008 | 塑料.增塑聚氯乙烯(PVC-P)的模塑和挤塑材料.试样制备和特性测定 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding andextrusion materials - Part 2: Preparation of test specimens anddetermination of properties |
| BS EN ISO 291-2008 | 塑料.调节和测试用标准大气 | Plastics - Standard atmospheres for conditioning and testing |
| BS EN ISO 293-2006 | 塑料.热塑性材料的压塑试样 | Plastics - Compression moulding of test specimens of thermoplastic materials |
| BS EN ISO 294-1-1997 | 塑料.热塑材料试样喷射铸造.第1部分:一般原则、多用途棒材试样模铸 | Plastics - Injection moulding of test specimens of thermoplastic materials - General principles, and moulding of multipurpose and bar test specimens |
| BS EN ISO 294-3-2003 | 塑料.热塑性材料试样的注射模塑法.小板 | Plastics - Injection moulding of test specimens of thermoplastic materials - Small plates |
| BS EN ISO 294-4-2003 | 塑料.热塑塑料试样的注射成形.第4部分:模型收缩率的测定 | Plastics - Injection moulding of test specimens of thermoplastic materials - Determination of moulding shrinkage |
| BS EN ISO 295-2004 | 塑料.热固性材料试样的压模塑法 | Plastics - Compression moulding of test specimens of thermosetting materials |
| BS EN ISO 3001-1999 | 塑料.环氧化合物.环氧基当量的测定 | Plastics - Epoxy compounds - Determination of epoxy equivalent |
| BS EN ISO 305-1999 | 塑料.与聚氯乙烯相关的含氯聚合物、共聚物及其混合物的热稳定性的测定.色变法 | Plastics - Determination of thermal stability of poly (vinyl chloride) related chlorine-containing homopolymers and copolymers and their compounds - Discoloration method |
| BS EN ISO 306-2004 | 塑料.热塑性材料.维卡(VICAT)软化温度的测定 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) |
| BS EN ISO 307-2007 | 塑料.聚酰胺.粘度值的测定 | Plastics - Polyamides - Determination of viscosity number |
| BS EN ISO 308-1998 | 塑料.酚制模材料.丙酮可溶性物质测定(非制模状态下树脂含量) | Plastics - Phenolic moulding materials - Determination of acetone-soluble matter (apparent resin content of material in the unmoulded state) |
| BS EN ISO 3126-2006 | 塑料管道系统.塑料部件.尺寸测定 | Plastics piping systems - Plastics components - Determination of dimensions |
| BS EN ISO 3146-2000 | 塑料.用毛细管和偏振显微镜法测定半晶状聚合物的熔化性能(熔化温度或熔化区域) | Plastics - Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
| BS EN ISO 3167-2003 | 塑料.多用途试样 | Plastics - Multipurpose test specimens |
| BS EN ISO 3219-1994 | 塑料.液态或乳状态或分散剂作用的聚合物/树脂.用具有规定剪切率的旋转式粘度计测定粘度 | Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate |
| BS EN ISO 3251-2008 | 涂料、清漆和塑料.非挥发物质含量的测定 | Paints, varnishes and plastics - Determination of non- volatile-matter content |
| BS EN ISO 3451-4-2000 | 塑料.灰份的测定.聚酰胺 | Plastics - Determination of ash - Polyamides |
| BS EN ISO 3451-5-2002 | 塑料.灰分测定.聚氯乙烯 | Plastics - Determination of ash - Poly(vinyl chloride) |
| BS EN ISO 3521-2000 | 塑料.不饱和聚酯和环氧树脂.总体积收缩量的测定 | Plastics - Unsaturated polyester and epoxy resins - Determination of overall volume shrinkage |
| BS EN ISO 3671-1999 | 塑料.氨基塑料模塑材料.挥发性物质的测定 | Plastics - Aminoplastic moulding materials - Determination of volatile matter |
| BS EN ISO 3672-1-2001 | 塑料.不饱和聚酯树脂.名称与符号系统 | Plastics - Unsaturated-polyester resins (UP-R) - Designation system |
| BS EN ISO 3672-2-2001 | 塑料.不饱和聚酯树脂.试样的制备和性能的测定 | Plastics - Unsaturated-polyester resins (UP-R) - Preparation of test specimens and determination of properties |
| BS EN ISO 3673-1-2000 | 塑料.环氧树脂.名称与符号 | Plastics - Epoxy resins - Designation |
| BS EN ISO 3673-2-2000 | 塑料.环氧树脂.试样的制备和特性的测量 | Plastics - Epoxy resins - Preparation of test specimens and determination of properties |
| BS EN ISO 3826-1-2003 | 人体血液及血液成分用塑料折叠容器.常规容器 | Plastics collapsible containers for human blood and blood components - Conventional containers |
| BS EN ISO 3826-2-2008 | 人类血液及血液成分用塑料可折叠容器.用于标签和说明手册上的图形符号 | Plastics collapsible containers for human blood and bloodcomponents - Part 2: Graphical symbols for use on labels andinstruction leaflets |
| BS EN ISO 3826-3-2007 | 人体血液及血液成分袋式塑料容器.具有综合特征的采血袋设备 | Plastics collapsible containers for human blood and blood components - Blood bag systems with integrated features |
| BS EN ISO 3915-1999 | 塑料.导电塑料电阻率的测量 | Plastics - Measurement of resistivity of conductive plastics |
| BS EN ISO 3994-2001 | 塑料软管.抽吸和排放含水物的螺旋型热塑增强的热塑软管.规范 | Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification |
| BS EN ISO 4577-1999 | 塑料.聚丙烯和丙烯共聚物.空气中热氧化稳定性的测定.烘箱法 | Plastics - Polypropylene and propylene-copolymers - Determination of thermal oxidative stability in air - Oven method |
| BS EN ISO 4589-1-2000 | 塑料.通过氧指数测定其燃烧性.指南 | Plastics - Determination of burning behaviour by oxygen index - Guidance |
| BS EN ISO 4589-2-1999 | 塑料.通过氧指数测定其燃烧性.室温试验 | Plastics - Determination of burning behaviour by oxygen index - Ambient-temperature test |
| BS EN ISO 4589-3-1996 | 塑料.通过氧指数测定其燃烧性.第3部分:高温试验 | Plastics - Determination of burning behaviour by oxygen index - Elevated temperature test |
| BS EN ISO 4590-2003 | 硬质泡沫塑料.开孔和闭孔泡沫的容积百分比的测定 | Rigid cellular plastics - Determination of the volume percentage of open cells and of closed cells |
| BS EN ISO 4608-1998 | 塑料.一般用途的氯乙烯均聚物和共聚物树脂.室温下增塑剂吸收性的测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride for general use - Determination of plasticizer absorption at room temperature |
| BS EN ISO 4610-2001 | 塑料.氯乙烯均聚物和共聚物树脂.用喷气式的筛滤器的筛析 | Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis using air-jet sieve apparatus |
| BS EN ISO 4611-2008 | 塑料.暴露于湿热、喷水和盐雾中产生效应的测定 | Plastics - Determination of the effects of exposure to damp heat,water spray and salt mist |
| BS EN ISO 4612-1999 | 塑料.试验用PVC糊料的制备.齿轮传动混合方法 | Plastics - Preparation of PVC pastes for test purposes - Planetary-mixer method |
| BS EN ISO 4613-1-1999 | 塑料.醋酸乙烯/乙烯酯(E/VAC)模压和挤压材料.标示和规范 | Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Designation and specification |
| BS EN ISO 4613-2-1996 | 塑料.乙烯/醋酸乙烯脂模塑和挤出材料.第2部分:试样的制备和性能的测定 | Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 4614-2000 | 塑料.三聚氰胺--甲醛模塑.可萃取的甲醛的测定 | Plastics - Melamine-formaldehyde mouldings - Determination of extractable formaldehyde |
| BS EN ISO 4615-1999 | 塑料.未饱和聚酯和环氧树脂.氯的总含量的测定 | Plastics - Unsaturated polyesters and epoxide resins - Determination of total chlorine content |
| BS EN ISO 4651-1995+A1-2008 | 泡沫橡胶和塑料.动态缓冲性能的测定 | Cellular rubbers and plastics - Determination of dynamic cushioning performance |
| BS EN ISO 4671-2008 | 橡胶、塑料软管和软管组件.软管尺寸和软管组件长度的测量方法 | Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies |
| BS EN ISO 4672-1999 | 橡胶和塑料软管.低于室温的柔性试验 | Rubber and plastics hoses - Sub-ambient temperature flexibility tests |
| BS EN ISO 4674-1-2003 | 橡胶或塑料涂覆织物.抗撕裂性测定.恒定撕裂速率法 | Rubber- or plastics-coated fabrics - Determination of tear resistance - Constant rate of tear methods |
| BS EN ISO 4674-2-1998 | 橡胶或塑料涂覆织物.抗撕裂性的测定.冲击摆锤法 | Rubber- or plastics-coated fabrics - Determination of tear resistance - Ballistic pendulum method |
| BS EN ISO 472-2001 | 塑料.词汇 | Plastics - Vocabulary |
| BS EN ISO 483-2006 | 塑料.使用水溶液进行调节和试验保持恒定湿度的小型密封容器 | Plastics - Small enclosures for conditioning and testing using aqueous solutions to maintain the humidity at constant value |
| BS EN ISO 489-1999 | 塑料.反射指数的测定 | Plastics - Determination of refractive index |
| BS EN ISO 4892-1-2001 | 塑料.实验室光源暴露法.一般指南 | Plastics - Methods of exposure to laboratory light sources - General guidance |
| BS EN ISO 4892-2-2006 | 塑料.实验室光源暴露法.氙弧灯 | Plastics - Methods of exposure to laboratory light sources - Xenon-arc lamps |
| BS EN ISO 4892-3-2006 | 塑料.暴露到实验室光源的方法.UV荧光灯 | Plastics - Methods of exposure to laboratory light sources - Fluorescent UV lamps |
| BS EN ISO 4894-1-1999 | 塑料.苯乙烯/丙烯腈(SAN)共聚物的模塑和挤塑材料.名称与符号系统和规范基础 | Plastics - Styrene/acrylonitrile (SAN) copolymer moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 4894-2-1999 | 塑料.苯乙烯/丙烯腈(SAN)共聚物的模塑和挤塑材料.试样制备和特性测定 | Plastics - Styrene/acrylonitrile (SAN) copolymer moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 4895-2000 | 塑料.液态环氧树脂.结晶倾向的测定 | Plastics - Liquid epoxy resins - Determination of tendency to crystallize |
| BS EN ISO 527-1-1994 | 塑料.拉伸性能测定.第1部分:总则 | Plastics - Determination of tensile properties - General principles |
| BS EN ISO 527-2-1994 | 塑料.拉伸性能测定.第2部分:模压和挤压塑料试验条件 | Plastics - Determination of tensile properties - Test conditions for moulding and extrusion plastics |
| BS EN ISO 527-3-1996 | 塑料.塑料抗拉性能的测定.第3部分:薄膜和薄板材试验条件 | Plastics - Determination of tensile properties - Test conditions for films and sheets |
| BS EN ISO 527-4-1997 | 塑料.抗拉性能测定.第4部分:正交同性和正交异性纤维试验条件.增强塑料复合材料 | Plastics - Determination of tensile properties - Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| BS EN ISO 5470-1-1999 | 涂橡胶或塑料的织物.耐磨性的测定.Taber磨蚀机 | Rubber- or plastics-coated fabrics - Determination of abrasion resistance - Taber abrader |
| BS EN ISO 5470-2-2003 | 橡胶或塑料涂层织物.耐磨损性测定.马丁代尔研磨器 | Rubber- or plastics-coated fabrics - Determination of abrasion resistance - Martindale abrader |
| BS EN ISO 5659-1-1999 | 塑料.起烟.光密度测定指南 | Plastics - Smoke generation - Guidance on optical-density testing |
| BS EN ISO 5659-2-2007 | 塑料.烟雾产生.用单室试验测定的光密度 | Plastics - Smoke generation - Determination of optical density by a single-chamber test |
| BS EN ISO 5774-2008 | 塑料软管.压缩空气用织物增强型软管组件.规范 | Plastic hoses - Textile-reinforced types for compressed-air applications - Specification |
| BS EN ISO 580-2005 | 塑料管和管道系统.喷射模铸热塑性配件.热效应直观评估法 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating |
| BS EN ISO 584-1998 | 塑料.不饱和聚酯树脂.80℃时的反应性测定(常规方法) | Plastics - Unsaturated polyester resins - Determination of reactivity at 80 °C (conventional method) |
| BS EN ISO 585-1999 | 塑料.非增塑的乙酸纤维素.水分含量的测定 | Plastics - Unplasticized cellulose acetate - Determination of moisture content |
| BS EN ISO 5981-2007 | 橡胶或塑料涂层织物.抗复合弯曲剪切和磨损的测定 | Rubber or plastics-coated fabrics - Determination of resistance to combined shear flexing and rubbing |
| BS EN ISO 60-2000 | 塑料.可由专用漏斗注入的材料的表观密度测定 | Plastics - Determination of apparent density of material that can be poured from a specified funnel |
| BS EN ISO 604-2003 | 塑料.压缩性能的测定 | Plastics - Determination of compressive properties |
| BS EN ISO 61-2000 | 塑料.不能由专用漏斗注入的模塑材料表观密度的测定 | Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel |
| BS EN ISO 6186-1999 | 塑料.可浇注性的测定 | Plastics - Determination of pourability |
| BS EN ISO 62-2008 | 塑料.吸水率测定 | Plastics - Determination of water absorption |
| BS EN ISO 6383-1-1991 | 塑料.薄膜和薄板.耐撕裂性测定.分岔裤型撕裂法(Trouser) | Plastics - Film and sheeting - Determination of tear resistance - Trouser tear method |
| BS EN ISO 6383-2-1991 | 塑料.薄膜和薄板.耐撕裂性测定.埃尔曼多(ELMENDORF)法 | Plastics - Film and sheeting - Determination of tear resistance - Elmendorf method |
| BS EN ISO 6401-2008 | 塑料.聚氯乙烯.剩余氯乙烯单体的测定.气相色谱法 | Plastics — Poly(vinyl chloride) — Determination ofresidual vinyl chloride monomer — Gaschromatographic method (ISO 6401:2008) |
| BS EN ISO 6402-1-2002 | 塑料.丁二烯改性材料除外的丙烯腈/苯乙烯模塑和压塑材料(ASA、AES和ACS)的耐冲击性能.命名与符号系统和规范 | Plastics - Impact resistant acrylonitrile/styrene moulding and extrusion materials (ASA, AES, ACS), excluding butadiene-modified materials - Designation system and basis for specifications |
| BS EN ISO 6402-2-2004 | 塑料.丙烯腈-苯乙烯-丙烯酸酯、丙烯腈-(乙烯-丙烯-二烯烃)-苯乙烯和丙烯腈-(氯化聚乙烯)-苯乙烯模塑和挤塑 | Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 6603-1-2000 | 塑料.硬质塑料复合轴向冲击性能的测定.非仪器冲击试验 | Plastics - Determination of multi-axial impact behaviour of rigid plastics - Non-instrumented impact testing |
| BS EN ISO 6603-2-2000 | 塑料.硬质塑料多轴向冲击性能的测定.设备冲击试验 | Plastics - Determination of multi-axial impact behaviour of rigid plastics - Instrumented puncture testing |
| BS EN ISO 6721-1-2002 | 塑料.动态机械性能的测定.一般原则 | Plastics - Determination of dynamic mechanical properties - General principles |
| BS EN ISO 6721-2-2008 | 塑料.动力机械性能的测定.扭摆法 | Plastics - Determination of dynamic mechanical properties - Torsion-pendulum method |
| BS EN ISO 6721-3-1996 | 塑料.动态机械性能的测定.第3部分:弯曲振动.共振曲线法 | Plastics - Determination of dynamic mechanical properties - Flexural vibration - Resonance-curve method |
| BS EN ISO 6802-2008 | 钢丝增强的橡胶和塑料软管及软管组件.弯曲液压脉冲试验 | Rubber and plastics hoses and hose assemblies with wirereinforcements - Hydraulic impulse test with flexing |
| BS EN ISO 6803-2008 | 橡胶或塑料软管及软管组件.无挠性液压脉冲试验 | Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing |
| BS EN ISO 6808-2001 | 石油类液体抽吸和低压排放用塑料软管和软管组件.规范 | Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification |
| BS EN ISO 7214-2007 | 泡沫塑料.聚乙烯.试验方法 | Cellular plastics - Polyethylene - Methods of test |
| BS EN ISO 7233-2008 | 橡胶、塑料软管和软管组件.耐真空度的测定 | Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum |
| BS EN ISO 7326-2008 | 橡胶和塑料软管.静态条件下评定耐臭氧性 | Rubber and plastics hoses - Assessment of ozone resistance under static conditions |
| BS EN ISO 7327-1996 | 塑料.环氧树脂用固化剂和促进剂.酸酐中游离酸测定 | Plastics - Hardeners and accelerators for epoxide resins - Determination of free acid in acid anhydride |
| BS EN ISO 7391-1-2006 | 塑料.聚碳酸酯(PC)模塑和挤塑材料.名称与符号系统和基本规范 | Plastics - Polycarbonate (PC) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 7391-2-2006 | 塑料.聚碳酸酯(PC)模塑和挤塑材料.试样制备和特性测定 | Plastics - Polycarbonate (PC) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 75-1-2004 | 塑料.载荷下挠曲温度的测定.一般试验方法 | Plastics - Determination of temperature of deflection under load - General test method |
| BS EN ISO 75-2-2004 | 塑料.载荷下挠曲温度的测定.塑料、硬橡胶和长纤维增强合成物 | Plastics - Determination of temperature of deflection under load - Plastics and ebonite |
| BS EN ISO 75-3-2004 | 塑料.载荷下挠曲温度的测定.高强度热固性叠层板材 | Plastics - Determination of temperature of deflection under load - High-strength thermosetting laminates and long-fibre-reinforced plastics |
| BS EN ISO 7662-1996 | 橡胶和塑料软管.内衬磨损的测定 | Rubber and plastics hoses - Determination of abrasion of lining |
| BS EN ISO 7686-2006 | 塑料管和配件.不透明度的测定 | Plastics pipes and fittings - Determination of opacity |
| BS EN ISO 7751-1997 | 橡胶和塑料软管和软管组件.试验压力和爆破压力与设计工作压力之比 | Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to design working pressure |
| BS EN ISO 7765-1-1996 | 塑料薄膜和薄板.由自由落体物法测定抗冲击性.梯级法 | Plastics film and sheeting - Determination of impact resistance by the free-falling dart method - Staircase methods |
| BS EN ISO 7792-1-1998 | 塑料.热塑聚酯模塑和挤制材料.命名系统和基本规范 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 7792-2-1998 | 塑料.热塑性聚酯(TP)模塑和挤塑材料.试样的制备和性能的测定 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 7808-1999 | 塑料.热固性模制塑料.传输塑变性的测定 | Plastics - Thermosetting moulding materials - Determination of transfer flow |
| BS EN ISO 7822-1999 | 纺织玻璃纤维增强的塑料.空隙量的测定.灼烧损失、机械粉碎和统计计数法 | Textile glass reinforced plastics - Determination of void content - Loss on ignition, mechanical disintegration and statistical counting methods |
| BS EN ISO 7823-1-2003 | 塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和特性.浇注薄板材 | Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Cast sheets |
| BS EN ISO 7823-3-2007 | 塑料.聚丙烯酸甲酯薄膜.型式、尺寸和特征.连续浇铸薄膜 | Plastics - Poly(methacrylate) sheets - Types, dimensions and characteristics - Continuous cast sheets |
| BS EN ISO 7854-1996 | 橡胶或塑料涂覆织物.耐折曲损坏性的测定 | Rubber- or plastics-coated fabrics - Determination of resistance to damage by flexing |
| BS EN ISO 7965-2-1995 | 包装.包装袋.跌落试验.第2部分:热塑性塑料软簿膜包装袋 | Sacks - Drop test - Sacks made from thermoplastic flexible film |
| BS EN ISO 8028-2000 | 无空气涂料喷涂用塑料和/或橡胶软管组件.规范 | Rubber and/or plastics hose assemblies for airless paint spraying - Specification |
| BS EN ISO 8030-1998 | 橡胶和塑料软管.易燃性试验方法 | Rubber and plastics hoses - Method of test for flammability |
| BS EN ISO 8031-2009 | 橡胶和塑料软管和软管组件.电阻率和电导率的测定 | Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity |
| BS EN ISO 8033-2006 | 橡胶和塑料软管.部件间粘合力的测定 | Rubber and plastics hoses - Determination of adhesion between components |
| BS EN ISO 8256-2004 | 塑料.拉伸冲击强度测定 | Plastics - Determination of tensile-impact strength |
| BS EN ISO 8308-2008 | 橡胶和塑料软管及软管组件.液体透过软管及其组件管壁的渗透性能的测定 | Rubber and plastics hoses and tubing - Determination of transmission of liquids through hose and tubing walls |
| BS EN ISO 8330-2008 | 橡胶和塑料软管和软管组件.词汇 | Rubber and plastics hoses and hose assemblies - Vocabulary |
| BS EN ISO 844-2009 | 硬质泡沫塑料.压缩特性测定 | Rigid cellular plastics - Determination of compression properties |
| BS EN ISO 846-1997 | 塑料.微生物作用的评定. | Plastics - Evaluation of the action of microorganisms |
| BS EN ISO 8580-1989 | 橡胶和塑料软管.静态抗紫外线辐射测试 | Rubber and plastics hoses - Determination of ultra-violet resistance under static conditions |
| BS EN ISO 8619-2005 | 塑料.酚醛树脂粉.在加热的玻璃板上流动距离的测定 | Plastics - Phenolic resin powder - Determination of flow distance on a heated glass plate |
| BS EN ISO 868-2003 | 塑料和硬质橡胶.用硬度计测定压痕硬度(肖氏硬度) | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) |
| BS EN ISO 877-1996 | 塑料.用玻璃滤日光镜测定直接暴露风化和用屈折反光镜测定日光增强风化的方法 | Plastics - Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and to intensified weathering by daylight using Fresnel mirrors |
| BS EN ISO 8795-2002 | 用于输送供人消耗用水的塑料管道系统.析出物渗移量的车测定.塑料管道、管件和连接件的析出物渗移量的测定 | Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints |
| BS EN ISO 8974-2002 | 塑料.酚醛树脂.用气相色谱法测定残余酚含量 | Plastics - Phenolic resins - Determination of residual phenol content by gas chromatography |
| BS EN ISO 8975-1995 | 塑料.酚醛树脂.pH值的测定 | Plastics - Phenolic resins - Determination of pH |
| BS EN ISO 8985-1998 | 塑料.乙烯/乙烯基醋酸盐共聚物(ENAC)热塑性塑料.乙烯基醋酸盐含量的测定 | Plastics - Ethylene/vinyl acetate copolymer (EVAC) thermoplastics - Determination of vinyl acetate content |
| BS EN ISO 8986-1-2009 | 塑料.聚丁烯-1(PB-1)的模塑和挤塑材料.名称与符号系统和规范基础 | Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Designation system and basis for specifications |
| BS EN ISO 8986-2-2009 | 塑料.聚丁烯-1(PB-1)的模塑和挤塑材料.试样制备和性能测定 | Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS EN ISO 8987-2006 | 塑料.酚醛树脂.aB-转换离子试验板上的活性测定 | Plastics - Phenolic resins - Determination of reactivity on aB-transformat ion test plate |
| BS EN ISO 8988-2006 | 塑料.酚醛树脂.六亚甲基四胺含量的测定.凯氏法、过氯酸法和盐酸法 | Plastics - Phenolic resins - Determination of hexamethylene-tetramine content - Kjeldahl method, perchloric acid method and hydrochloric acid method |
| BS EN ISO 8989-1998 | 塑料.液体酚醛树脂.水混溶性的测定 | Plastics - Liquid phenolic resins - Determination of water miscibility |
| BS EN ISO 899-1-2003 | 塑料.蠕变的测定.拉伸蠕变 | Plastics - Determination of creep behaviour - Tensile creep |
| BS EN ISO 899-2-2003 | 塑料.蠕变的测定.用三点加载法测定挠曲蠕变 | Plastics - Determination of creep behaviour - Flexural creep by three-point loading |
| BS EN ISO 9054-1999 | 硬质泡沫塑料.自结皮高密度材料的试验方法 | Cellular plastics, rigid - Test methods for self-skinned high-density materials |
| BS EN ISO 9080-2003 | 塑料管道和导管系统.用外推法测定热塑塑料管道的长期静液压强度 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| BS EN ISO 9311-2-2002 | 热塑性塑料管道系统用胶粘剂.剪切强度的测定 | Adhesives for thermoplastic piping systems - Determination of shear strength |
| BS EN ISO 9396-2001 | 塑料.酚醛树脂.用自动装置测定在给定温度下的凝胶时间 | Plastics - Phenolic resins - Determination of the gel time at a given temperature using automatic apparatus |
| BS EN ISO 9702-1997 | 塑料.环氧氨硬化剂.对第1、2、3 氨组含氮量的测定 | Plastics - Amine epoxide hardeners - Determination of primary, secondary and tertiary amine group nitrogen content |
| BS EN ISO 9771-1997 | 塑料.酚醛树脂.测定可溶酚醛树脂在酸性条件下凝固时假绝热温升 | Plastics - Phenolic resins - Determination of the pseudo-adiabatic temperature rise of liquid resols when cured under acid conditions |
| BS EN ISO 9773-1999 | 塑料.与小火焰源接触的薄型垂直软样件的燃烧性能的测定 | Plastics - Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source |
| BS EN ISO 9944-1995 | 塑料.酚醛树脂.树脂萃取物电导率的测定 | Plastics - Phenolic resins - Determination of electrical conductivity of resin extracts |
| BS EN ISO 9967-2008 | 热塑性塑料管.蠕变率的测定 | Thermoplastics pipes - Determination of creep ratio |
| BS EN ISO 9969-2008 | 热塑性塑料管.环压挺度的测定 | Thermoplastics pipes - Determination of ring stiffness |
| BS EN ISO 9988-1-2004 | 塑料.聚甲醛模塑和挤塑材料.命名体系和规范基础 | Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Designation system and basis for specifications |
| BS ISO 10113-2006 | 金属材料.薄板材和带材.测定塑料应力 | Metallic materials - Sheet and strip - Determination of plastic strain ratio |
| BS ISO 10371-1995 | 纤维加强塑料.复合加强材料用编织带.规范基础 | Fibre reinforced plastics - Braided tapes for composite materials reinforcement - Basis for a specification |
| BS ISO 1043-2-2000 | 塑料.符号和缩略语.填充剂和增强材料 | Plastics. Symbols and abbreviated terms. Fillers and reinforcing materials |
| BS ISO 10724-1-1998 | 塑料.热固粉末模塑复合物试样的注射模塑成型.第1部分:多用途试样的一般原理和模塑成型 | Plastics. Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs). General principles and moulding of multipurpose test specimens |
| BS ISO 10724-2-1999 | 塑料.热固粉末模塑复合物试样的注射模塑成型.小板材 | Plastics. Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs). Small plates |
| BS ISO 10838-3-2001 | 燃气用聚乙烯管道系统的机械式管件.标称外径小于或等于63mm的管道用热塑性塑料管件 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Thermoplastic fittings for pipes of nominal outside diameter less than or equal to 63mm |
| BS ISO 10840-2008 | 塑料.标准着火试验使用指南 | Plastics - Guidance for the use of standard fire tests |
| BS ISO 10952-2008 | 塑料管道系统.玻璃增强热固性塑料(GRP)管道和管件.变形条件下部件内部耐化学腐蚀性的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack for the inside of a section in deflected condition |
| BS ISO 11357-2-1999 | 塑料.差示扫描量热法(DSC).玻璃传导温度的测定 | Plastics - Differential scanning calorimetry (DSC) - Determination of glass transition temperature |
| BS ISO 11357-3-1999 | 塑料.差示扫描量热法(DSC).熔化和结晶焓和温度的测定 | Plastics - Differential scanning calorimetry (DSC) - Determination of temperature and enthalpy of melting and crystallization |
| BS ISO 11357-4-2006 | 塑料.差示扫描量热法(DSC).测定比热容量 | Plastics - Differential scanning calorimetry (DSC) - Determination of specific heat capacity |
| BS ISO 11357-5-2001 | 塑料.差示扫描量热法(DSC).特性的测定：反应曲线温度、时间、反应焓和转化度 | Plastics - Differential scanning calorimetry (DSC) - Determination of characteristic reaction-curve temperatures and times, enthalphy of reaction and degree of conversion |
| BS ISO 11357-6-2008 | 塑料.差示扫描量热法(DSC).氧化诱导时间(等温OIT)和氧化感应温度(动力OIT)的测定 | Plastics - Differential scanning calorimetry (DSC) - Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| BS ISO 11357-7-2002 | 塑料.差示扫描量热法(DSC).晶体化动力的测定 | Plastics - Differential scanning calorimetry (DSC) - Determination of crystallization kinetics |
| BS ISO 11358-2-2005 | 塑料.高聚物的热重分析法(TG).活化能测定 | Plastics - Thermographimetry (TG) of polymers - Determination of activation energy |
| BS ISO 11359-1-1999 | 塑料.热力学分析(TMA).一般原则 | Plastics - Thermomechanical analysis (TMA) - General principles |
| BS ISO 11359-2-1999 | 塑料.热力学分析(TMA).线性热膨胀系数和玻璃化转变温度的测定 | Plastics - Thermomechanical analysis (TMA) - Determination of coefficient of linear thermal expansion and glass transition temperature |
| BS ISO 11359-3-2002 | 塑料.热力学分析(TMA).渗透温度的测定 | Plastics - Thermomechanical analysis (TMA) - Determination of penetration temperature |
| BS ISO 11403-1-1996 | 塑料.可比较的多点数据采集和表述.第1部分:机械性能 | Plastics. Acquisition and presentation of comparable multipoint data. Mechanical |
| BS ISO 11413-2008 | 塑料管和配件.聚乙烯(PE)管和电熔配件试样组件的制备 | Plastics pipes and fittings - Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting |
| BS ISO 11414-2009 | 塑料管和配件.通过熔接制备聚乙烯(PE)管/管或管/配件试样组装件 | Plastics pipes and fittings - Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| BS ISO 11443-2005 | 塑料.用毛细管和狭缝流变仪测定塑料的流动性 | Plastics - Determination of the fluidity of plastics using capillary and slit-die rheometers |
| BS ISO 11561-1999 | 热绝缘材料的老化.闭孔塑料耐热性能的长期变化量的测定(加速实验室试验方法) | Ageing of thermal insulation materials - Determination of the long-term change in thermal resistance of closed-cell plastics (accelerated laboratory test methods) |
| BS ISO 1163-1-1996 | 塑料.未增塑聚氯乙烯模制和挤制材料.第1部分:标记系统和基础规范 | Plastics. Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials. Designation system and basis for specifications |
| BS ISO 11667-1997 | 纤维增强塑料.模压化合物和聚酯胶片.树脂、增强纤维和矿物填料含量测定.溶解方法 | Fibre reinforced plastics. Moulding compounds and prepregs. Determination of resin, reinforcement-fibre and mineral-filler content. Dissolution methods |
| BS ISO 11907-1-1998 | 塑料制品.烟雾生成.灭火废液腐蚀性的测定.第1部分:指南 | Plastics - Smoke generation - Determination of the corrosivity of fire effluents - Guidance |
| BS ISO 11907-2-1996 | 塑料制品.烟雾生成.火灾流出物腐蚀性的测定.第2部分:静态法 | Plastics - Smoke generation - Determination of the corrosivity of fire effluents - Static method |
| BS ISO 11907-3-1998 | 塑料制品.烟雾生成.灭火废液腐蚀性的测定.第3部分:采用移动式熔炉的动态分解法 | Plastics - Smoke generation - Determination of the corrosivity of fire effluents - Dynamic decomposition method using a travelling furnace |
| BS ISO 11907-4-1998 | 塑料制品.烟雾生成.灭火废液腐蚀性的测定.第4部分:采用圆锥形辐射加热器的动态分解法 | Plastics - Smoke generation - Determination of the corrosivity of fire effluents - Dynamic decomposition method using a conical radiant heater |
| BS ISO 12000-2000 | 塑料/橡胶.聚合物的分散体及橡胶乳(天然的和合成的)的清析度.试验方法的确定和复审 | Plastics/rubber - Polymer dispersions and rubber latices (natural and synthetic) - Definitions and review of test methods |
| BS ISO 12176-2-2008 | 塑料管和配件.聚乙烯系统的熔接设备.电熔接 | Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Electrofusion |
| BS ISO 1268-1-2002 | 纤维增强塑料.试验板的制备方法.通用条件 | Fibre-reinforced plastics - Methods of producing test plates - General conditions |
| BS ISO 1268-10-2005 | 纤维增强塑料.试验板的生产方法.BMC和其他长纤维化合物的注射模塑法.多用途试样的一般原则和模制 | Fibre-reinforced plastics - Methods of producing test plates - Injection moulding of BMC and other long-fibre compounds - General principles and moulding of multipurpose test specimens |
| BS ISO 1268-11-2005 | 纤维增强塑料.试验板的生产方法.BMC和其他长纤维化合物的注射模塑法.小型试验板 | Fibre-reinforced plastics - Methods of producing test plates - Injection moulding of BMC and other long-fibre moulding compounds - Small plates |
| BS ISO 1268-2-2001 | 纤维增强塑料.试验板的制备方法.接触模压法和喷射成形法 | Fibre-reinforced plastics - Methods of producing test plates - Contact and spray-up moulding |
| BS ISO 1268-3-2000 | 纤维增强塑料.试验板的制备方法.湿压缩模塑法 | Fibre-reinforced plastics - Methods of producing test plates - Wet compression moulding |
| BS ISO 1268-4-2006 | 纤维增强塑料.试验用板材的生产方法.预浸料坯的摸制 | Fibre-reinforced plastics - Methods of producing test plates - Moulding of prepregs |
| BS ISO 1268-5-2001 | 纤维增强塑料.试验板的制备方法.长纤维缠绕 | Fibre-reinforced plastics - Methods of producing test plates - Filament winding |
| BS ISO 1268-6-2002 | 纤维增强塑料.试验用板材的生产方法.拉挤压制件 | Fibre-reinforced plastics - Methods of producing test plates - Pultrusion moulding |
| BS ISO 1268-7-2001 | 纤维增强塑料.试验板的生产方法.树脂转换模塑法 | Fibre-reinforced plastics - Methods of producing test plates - Resin transfer moulding |
| BS ISO 1268-8-2004 | 纤维增强塑料.试验板的生产方法.SMC和BMC压模 | Fibre-reinforced plastics - Methods of producing test plates - Compression moulding of SMC and BMC |
| BS ISO 1268-9-2003 | 纤维增强塑料.试验板的制备方法.GMT/STC的模制 | Fibre-reinforced plastics - Methods of producing test plates - Moulding of GMT/STC |
| BS ISO 12771-1997 | 实验室塑料制品器皿.可处理的血清移液管 | Plastics laboratory ware - Disposable serological pipettes |
| BS ISO 12992-1995 | 塑料制品.薄膜和薄板垂直火焰蔓延的测定 | Plastics - Vertical flame spread determination for film and sheet |
| BS ISO 13003-2004 | 纤维增强塑料.循环载荷条件下疲劳性能的测定 | Fibre-reinforced plastics - Determination of fatigue properties under cyclic loading conditions |
| BS ISO 13363-2004 | 船用发动机排湿系统用橡胶和塑料软管.规范 | Rubber and plastics hoses for marine-engine wet-exhaust systems - Specification |
| BS ISO 13586-2000 | 塑料.断裂韧性的测定(G<下标i><下标c>和K<下标i><下标c>).线性弹性断裂力学(LEFM)法 | Plastics - Determination of fracture toughness (Gic and Kic) - Linear elastic fracture mechanics (LEFM) approach |
| BS ISO 13741-1-1998 | 塑料制品/橡胶.聚合物弥散体和橡胶乳液(天然的和合成的).采用毛细管柱气相色谱分析法测定残余单基物和其他 | Plastics/rubber - Polymer dispersions and rubber latices (natural and synthetic) - Determination of residual monomers and other organic components by capillary-column gas chromatography - Direct liquid injection method |
| BS ISO 13741-2-1998 | 塑料制品/橡胶.聚合物弥散体和橡胶乳液(天然的和合成的).采用毛细管柱气相色谱分析法对残余单基物和其他有 | Plastics/rubber - Polymer dispersions and rubber latices (natural and synthetic) - Determination of residual monomers and other organic components by capillary-column gas chromatography - Headspace method |
| BS ISO 13774-1999 | 输送内燃机燃料用橡胶和塑料软管.易燃性试验方法 | Rubber and plastics hoses for fuels for internal combustion engines - Method of test for flammability |
| BS ISO 13802-1999 | 塑料.摆锤冲击试验机的鉴定.Charpy,Izod和拉伸冲击试验 | Plastics - Verification of pendulum impact-testing machines - Charpy, Izod and tensile impact-testing |
| BS ISO 13950-2007 | 塑料管和管件.电熔合接头用自动识别系统 | Plastics pipes and fittings - Automatic recognition systems for electrofusion joints |
| BS ISO 1409-2007 | 塑料/橡胶.聚合物分散体和橡胶胶乳(天然的和合成的).用环形法测定表面张力 | Plastics/rubber - Polymer dispersions and rubber latices (natural and synthetic) Determination of surface tension by the ring method |
| BS ISO 14531-1-2003 | 塑料管道和配件.气体燃料输送用交联聚乙烯(PE-X)管道系统.米制系列.管规范 | Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Pipes |
| BS ISO 14531-2-2006 | 塑料管道和配件.气体燃料运输用交联聚乙烯管道系统.米制系列.规范.热熔连接用配件.熔焊连接 | Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Fittings for heat-fusion jointing |
| BS ISO 14531-3-2006 | 塑料管道和配件.气体燃料运输用交联聚乙烯管道系统.米制系列.规范.机械连接用配件(包括PE-X/金属转换) | Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Fittings for mechanical jointing (including PE-X/metal transitions) |
| BS ISO 14531-4-2006 | 塑料管道和配件.气体燃料运输工具用交联聚乙烯(PE-X)管道系统.米制系列.规范.系统设计和安装指南 | Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - System design and installation guidelines |
| BS ISO 14616-1997 | 塑料制品.聚乙烯、乙烯共聚物及其混合物的热缩膜.收缩应力和紧缩应力的测定 | Plastics - Heatshrinkable films of polyethylene, ethylene copolymers and their mixtures - Determination of the shrinkage stress and contraction stress |
| BS ISO 14663-1-2002 | 塑料.乙烯/乙烯醇共聚物模塑和压塑材料.命名系统和规范基本知识 | Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Designation system and basis for specifications |
| BS ISO 14663-2-2002 | 塑料.乙烯/乙烯醇共聚物模塑和压塑材料.式样制备和性能测定 | Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS ISO 14848-1998 | 塑料制品.不饱和聚酯树脂.130℃下反应性测定 | Plastics - Unsaturated-polyester resins - Determination of reactivity at 130 °C |
| BS ISO 14849-1999 | 塑料制品.苯酚甲醛注模.游离氨和胺化合物的测定.靛酚法 | Plastics - Phenol-formaldehyde mouldings - Determination of free ammonia and ammonium compounds - Indophenol method |
| BS ISO 14853-2005 | 塑料.含水系统中塑料材料的最大厌氧生物降解能力的测定.生物气产生的测量方法 | Plastics - Determination of the ultimate anaerobic biodegradation of plastic materials in an aqueous system - Method by measurement of biogas production |
| BS ISO 14855-1999 | 在控制复合条件下塑料材料最大需氧生物降解能力和非集合性的测定.离析二氧化碳的分析方法 | Determination of the ultimate aerobic biodegradability and disintegration of plastic materials under controlled composting conditions - Method by analysis of evolved carbon dioxide |
| BS ISO 14897-2002 | 塑料.生产聚氨基甲酸乙酯用多元醇.水含量测定 | Plastics - Polyols for use in the production of polyurethane - Determination of water content |
| BS ISO 14898-1999 | 塑料制品.聚氨酯生材料.芳香异氰酸酯.酸度测定 | Plastics - Polyurethane raw materials - Aromatic isocyanates - Determination of acidity |
| BS ISO 14899-2001 | 塑料制品.聚氨酯生产用多元醇.碱度测定 | Plastics - Polyols for use in the production of polyurethane - Determination of basicity |
| BS ISO 14900-2001 | 塑料制品.聚氨酯生产用多元醇.羟基数值测定 | Plastics - Polyols for use in the production of polyurethane - Determination of hydroxyl number |
| BS ISO 14910-1-1998 | 塑料制品.制模和挤压用热塑聚酯/酯和聚醚/酯弹性体.标记系统和规范基础 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Designation system and basis for specifications |
| BS ISO 14910-2-1998 | 塑料制品.制模和挤压用热塑聚酯/酯和聚醚/酯弹性体.试样制备和性能测定 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Preparation of test specimens and determination of properties |
| BS ISO 15014-2007 | 塑料.聚偏氟乙烯(PVDF)挤压薄膜.要求和试验方法 | Plastics - Extruded sheets of poly(vinylidene fluoride) (PVDF) - Requirements and test methods |
| BS ISO 15024-2002 | 纤维增强塑料复合材料.无方向性增强材料的模式I层间断裂韧性，GDOWNiDOWNc,的测定 | Fibre-reinforced plastic composites - Determination of mode I interlaminar fracture toughness, Gic, for unidirectionally reinforced materials |
| BS ISO 15028-2004 | 塑料.用于聚氨酯生产的芳香族异氰酸酯.可水解氯的测定 | Plastics - Aromatic isocyanates for use in the production of polyurethanes - Determination of hydrolysable chlorine |
| BS ISO 15033-2007 | 塑料.用高效液相色谱分析法(HPLC)测定己内酰胺及其环状和线性齐聚物 | Plastics - Determination of caprolactam and its cyclic and linear oligomers by HPLC |
| BS ISO 15038-1999 | 塑料.不饱和聚酯热固化材料的有机聚酯交联剂.活性氧含量的测定 | Plastics - Organic-perester crosslinking agents for unsaturated-polyester thermosetting materials - Determination of active-oxygen content |
| BS ISO 15064-2006 | 塑料.用于聚氨酯生产的芳香族异氰酸酯.在甲苯二异氰酸酯中异构体比率的测定 | Plastics - Aromatic isocyanates for use in the production of polyurethanes - Determination of the isomer ratio in tuluenediisocyanate |
| BS ISO 15100-2001 | 塑料制品.增强纤维.短切原丝.松密度的测定 | Plastics - Reinforcement fibres - Chopped strands - Determination of bulk density |
| BS ISO 15105-1-2007 | 塑料.薄膜和薄膜纸.用压差法测定气体穿透率 | Plastics - Film and sheeting - Determination of gas-transmission rate - Differential-pressure methods |
| BS ISO 15105-2-2003 | 塑料.薄膜和片材.气体传输率的测定.等压法 | Plastics - Film and sheeting - Determination of gas-transmission rate - Equal-pressure method |
| BS ISO 15106-4-2008 | 塑料.薄膜和薄板.水蒸气透过率的测定.气相色谱法探测传感器法 | Plastics - Film and sheeting - Determination of water vapour transmission rate - Gas-chromatographic detection sensor method |
| BS ISO 15314-2005 | 塑料.海上曝光法 | Plastics - Methods for marine exposure |
| BS ISO 15373-2001 | 塑料制品.聚合物分散体.游离甲醛含量的测定 | Plastics - Polymer dispersions - Determination of free formaldehyde |
| BS ISO 15509-2001 | 粘合剂.工程塑料接头粘合强度测定 | Adhesives - Determination of the bond strength of engineering-plastic joints |
| BS ISO 15527-2007 | 塑料.聚乙烯(PE-UHMW、PE-HD)压模薄板材.要求和试验方法 | Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods |
| BS ISO 15850-2002 | 塑料.测定拉伸-拉伸疲劳断裂延伸性.线性弹力断裂机械(LEFM)试验方法 | Plastics - Determination of tension-tension fatigue crack propagation - Linear elastic fracture mechanics (LEFM) approach |
| BS ISO 15985-2004 | 塑料.在高固相厌氧消化条件下测定最终厌氧生物降解和分解作用.释放的沼气分析法 | Plastics - Determination of the ultimate anaerobic biodegradation and disintegration under high-solids anaerobic-digestion conditions - Method by analysis of released biogas |
| BS ISO 15987-2003 | 塑料.薄膜和片材.双轴向取向聚酰胺(尼龙)薄膜 | Plastics - Film and sheeting - Biaxially oriented polyamide (nylon) films |
| BS ISO 15988-2003 | 塑料.薄膜和片材.双轴向取向聚对苯二甲酸乙酯(PET)薄膜 | Plastics - Film and sheeting - Biaxially oriented poly(ethylene terephthalate) (PET) films |
| BS ISO 16014-1-2003 | 塑料.用粒度排除色谱法测定聚合物中平均分子量和分子量的分布.一般原则 | Plastics - Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography - General principles |
| BS ISO 16014-2-2003 | 塑料.用粒度排除色谱法测定聚合物的平均分子量和分子量的分布.通用校准法 | Plastics - Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography - Universal calibration method |
| BS ISO 16014-3-2003 | 塑料.用粒度排除色谱法测定聚合物中平均分子量和分子量的分布.低温法 | Plastics - Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography - Low-temperature method |
| BS ISO 16014-4-2003 | 塑料.用粒度排除色谱法测定平均分子量和分子量分布.高温法 | Plastics - Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography - High-temperature method |
| BS ISO 16152-2005 | 塑料.聚丙烯中二甲苯可溶物测定 | Plastics - Determination of xylene-soluble matter in polypropylene |
| BS ISO 1622-1-1994 | 塑料.聚苯乙烯(PS)模塑和挤塑材料.标记体系和基础规范 | Plastics. Polystrene (PS) moulding and extrusion materials. Designation system and basis for specifications |
| BS ISO 1622-2-1996 | 塑料.聚苯乙烯模塑和挤塑材料.第2部分:性能的测定 | Plastics. Polystrene (PS) moulding and extrusion materials. Preparation of test specimens and determination of properties |
| BS ISO 1628-5-1998 | 塑料.使用毛细管粘度计在稀溶液中测定聚合物的粘度.第5部分:热塑性聚酯均聚物和共聚物 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Thermoplastic polyester (TP) homopolymers and copolymers |
| BS ISO 16770-2004 | 塑料.聚乙烯的环境应力断裂测定.全切口蠕变试验 | Plastics - Determination of environmental stress cracking (ESC) of polyethylene - Full-notch creep test (FNCT) |
| BS ISO 16790-2005 | 塑料.热塑性塑料熔融状态下的拉伸特性测定 | Plastics - Determination of drawing characteristics of thermoplastics in the molten state |
| BS ISO 16869-2008 | 塑料.塑料配方设计中抑制真菌成分的功效评估 | Plastics - Assessment of the effectiveness of fungistatic compounds in plastics formulations |
| BS ISO 16929-2003 | 塑料.在小规模试验中在规定的弄污条件下塑料的分解度的测定 | Plastics - Determination of the degree of disintegration of plastic materials under defined composting conditions in a pilot-scale test |
| BS ISO 17282-2004 | 塑料.设计数据的获取和表示指南 | Plastics - Guide to the acquisition and presentation of design data |
| BS ISO 17422-2002 | 塑料.环境问题.标准中环境内容的一般导则 | Plastics - Environmental aspects - General guidelines for their inclusion in standards |
| BS ISO 17455-2007 | 塑料管道系统.多层管.屏蔽管的透氧性测定 | Plastics piping systems - Multilayer pipes - Determination of the oxygen permeability of the barrier pipe |
| BS ISO 17484-1-2006 | 塑料管道系统.最大工作压力达到5bar(500kPa)及以下的室内燃气装置用多层管道系统.系统规范 | Plastics piping systems - Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) - Specifications for systems |
| BS ISO 17555-2003 | 塑料.薄膜和薄板.双轴向取向的聚丙烯(PP)薄膜 | Plastics - Film and sheeting - Biaxially oriented polypropylene (PP) films |
| BS ISO 17556-2003 | 塑料.通过测量呼吸计中的需氧量或放出的二氧化碳量来测定土壤中的最大好氧生物降解能力 | Plastics - Determination of the ultimate aerobic biodegradability in soil by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved |
| BS ISO 17557-2003 | 塑料.薄膜和薄板.铸造的聚丙烯(PP)薄膜 | Plastics - Film and sheeting - Cast polypropylene (PP) films |
| BS ISO 17710-2002 | 塑料.生产聚氨基甲酸乙酯用多元醇.用微型滴定法测定不饱和度 | Plastics - Polyols for use in the production of polyurethane - Determination of degree of unsaturation by microtitration |
| BS ISO 17744-2004 | 塑料.作为温度和压力函数的比容的测定(pvT图).活塞装置法 | Plastics - Determination of specific volume as a function of temperature and pressure (pVT diagram) - Piston apparatus method |
| BS ISO 17771-2003 | 塑料.热固性模制化合物.SMC中纤维润湿程度的测定 | Plastics - Thermoset moulding compounds - Determination of the degree of fibre wetting in SMC |
| BS ISO 18225-2007 | 塑料管系统.室外气体装置用多层管道系统.系统规范 | Plastics piping systems - Multilayer piping systems for outdoor gas installations - Specifications for systems |
| BS ISO 18872-2007 | 塑料.测定高应变率拉伸特性 | Plastics - Determination of tensile properties at high strain rates |
| BS ISO 1922-2001 | 硬质泡沫塑料.剪切强度的测定 | Rigid cellular plastics - Determination of shear strength |
| BS ISO 1926-2009 | 硬质泡沫塑料.拉伸性能的测定 | Rigid cellular plastics - Determination of tensile properties |
| BS ISO 19712-1-2008 | 塑料.实心表面处理用装饰材料.分类和规范 | Plastics - Decorative solid surfacing materials - Classification and specifications |
| BS ISO 19712-2-2007 | 塑料.固体表面的装饰材料.性能测定.薄板材 | Plastics - Decorative solid surfacing materials - Determination of properties - Sheet goods |
| BS ISO 19712-3-2007 | 塑料.实心表面处理用装饰材料.性能测定.实心材料表面形状 | Plastics - Decorative solid surfacing materials - Determination of properties - Solid surface shapes |
| BS ISO 20200-2005 | 塑料.在实验室试验中模拟堆肥处理条件下测定塑料的分解度 | Plastics - Determination of the degree of disintegration of plastic materials under simulated composting conditions in a laboratory-scale test |
| BS ISO 20753-2008 | 塑料.试样 | Plastics - Test specimens |
| BS ISO 20848-1-2007 | 包装.塑料圆筒.标称容量113.6 L～220 L的活动开口圆桶 | Packaging - Plastics drums - Removable head (open head) drums with a nominal capacity of 113,6 l to 220 l |
| BS ISO 20848-2-2007 | 包装.塑料桶.标称容量208.2 L和220 L的固定盖(密封盖)圆桶 | Packaging - Plastics drums - Non-removable head (tight head) drums with a nominal capacity of 208,2 l and 220 l |
| BS ISO 20848-3-2007 | 包装.塑料圆筒.标称容量113.6 L～220 L塑料圆桶的塞子/桶孔关闭系统 | Packaging - Plastics drums - Plug/bungs closure systems for plastics drums with a nominal capacity of 113,6 l to 220 l |
| BS ISO 20965-2005 | 塑料.聚合物熔体瞬态拉伸粘度的测定 | Plastics - Determination of the transient extensional viscosity of polymer melts |
| BS ISO 21318-2007 | 塑料.环氧树脂.水树脂浸渍物电导性测定 | Plastics - Epoxy resins - Determination of electrical conductivity of aqueous resin extracts |
| BS ISO 21509-2006 | 塑料和硬质橡胶.肖氏硬度计的识别 | Plastics and ebonite - Verification of Shore durometers |
| BS ISO 22196-2007 | 塑料.塑料表面抗菌活性的测量 | Plastics - Measurement of antibacterial activity on plastics surfaces |
| BS ISO 22314-2006 | 塑料.玻璃纤维增强产品.纤维长度测定 | Plastics - Glass-fibre-reinforced products - Determination of fibre length |
| BS ISO 22498-2006 | 塑料.氯乙烯均聚物和共聚物树脂.采用机械筛分法进行的粒度测定 | Plastics - Vinyl chloride homopolymer and copolymer resins - Particle size determination by mechanical sieving |
| BS ISO 23559-2008 | 塑料.薄膜和薄板.热塑薄膜测试指南 | Plastics - Film and sheeting - Guidance on the testing of thermoplastic films |
| BS ISO 24538-2008 | 塑料.氯乙烯的均聚物和共聚树脂.使用干性粉末气相色谱分析测定残留氯乙烯单体 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of residual vinyl chloride monomer by gas-chromatographic analysis of dry powder |
| BS ISO 25137-1-2009 | 塑料.砜聚合物模制和挤出材料.标记系统和基础规范 | Plastics - Sulfone polymer moulding and extrusion materials - Designation system and basis for specifications |
| BS ISO 25137-2-2009 | 塑料.砜聚合物模制和挤出材料.试样的制备和性能的测定 | Plastics - Sulfone polymer moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS ISO 2561-2006 | 塑料.用气相色谱法测定聚苯乙烯(PS)和抗冲击聚苯乙烯(PS-I)中剩余的苯乙烯单体 | Plastics - Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas chromatography |
| BS ISO 25761-2008 | 塑料.聚氨酯的生产用多元醇.氮百分比表示的碱度(总胺值)的测定 | Plastics - Polyols for use in the production of polyurethanes - Determination of basicity (total amine value), expressed as percent nitrogen |
| BS ISO 2580-2-1995 | 塑料.丙烯腈-丁二烯-苯乙烯共聚物(ABS)的模塑和挤塑材料.试样制备和性能测定 | Plastics. Acrylonitrile/butadiene/styrene (ABS) moulding and extrusion materials. Preparation of test specimens and determination of properties |
| BS ISO 26603-2008 | 塑料.聚氨酯生产用芳族异氰酸盐.总氯含量的测定 | Plastics - Aromatic isocyanates for use in the production of polyurethanes - Determination of total chlorine |
| BS ISO 28702-2008 | 橡胶和塑料软管及管道.纺织物增强型.低于室温的变形试验 | Rubber and plastics hoses and tubing - Textile reinforced types - Sub-ambient temperature crush test |
| BS ISO 3011-1997 | 橡胶或塑料涂层织物.静态条件下抗臭氧龟裂的测定 | Rubber- or plastics-coated fabrics - Determination of resistance to ozone cracking under static conditions |
| BS ISO 3597-1-2003 | 纺织玻璃纤维增强塑料.无捻粗纱增强树脂棒力学性能的测定.棒的一般考虑和制备 | Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - General considerations and preparation of rods |
| BS ISO 3597-2-2003 | 纺织玻璃纤维增强塑料.无捻粗纱增强树脂棒力学性能的测定.弯曲强度的测定 | Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Determination of flexural strength |
| BS ISO 3597-3-2003 | 纺织玻璃纤维增强塑料.无捻粗纱增强树脂棒力学性能的测定.压缩强度的测定 | Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Determination of compressive strength |
| BS ISO 3597-4-2003 | 纺织玻璃纤维增强塑料.无捻粗纱增强树脂棒力学性能的测定.表观层间剪切强度的测定 | Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Determination of apparent interlaminar shear strength |
| BS ISO 366-4-2005 | 纺织机械和附件.钢筘.塑料连接金属钢筘的尺寸和标记 | Textile machinery and accessories - Reeds - Dimensions and designation of plastic-bound metal reeds |
| BS ISO 3672-1-2000 | 塑料.未饱和聚酯树脂(UP-R).标记系统 | Plastics. Unsaturated-polyester resins (UP-R). Designation system |
| BS ISO 3672-2-2000 | 塑料.未饱和聚酯树脂(UP-R).试样制备和性能测定 | Plastics. Unsaturated-polyester resins (UP-R). Preparation of test specimens and determination of properties |
| BS ISO 3826-3-2006 | 人类血液和血液成分用塑料可折叠容器.带综合特征采血袋系统 | Plastics collapsible containers for human blood and blood components - Blood bag systems with integrated features |
| BS ISO 4065-1997 | 热塑塑料管.通用壁厚表 | Thermoplastics pipes - Universal wall thickness table |
| BS ISO 4427-1-2007 | 塑料管道系统.给水用聚乙烯(PE)管和管件.总则 | Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - General |
| BS ISO 4427-2-2007 | 塑料管道系统.给水用聚乙烯(PE)管和管件.管 | Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Pipes |
| BS ISO 4427-3-2007 | 塑料管道系统.给水用聚乙烯(PE)管和管件.管件 | Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Fittings |
| BS ISO 4433-1-1998 | 热塑性塑料管.耐液体化学制品.分类.第1部分:浸入式试验 | Thermoplastic pipes - Resistance to liquid chemicals - Classification - Immersion test method |
| BS ISO 4433-2-1998 | 热塑塑料管.耐液体化学药品的性能.分类.聚烯烃管 | Thermoplastics pipes - Resistance to liquid chemicals - Classification - Polyolefin pipes |
| BS ISO 4433-3-1998 | 热塑性塑料管.耐液体化学制品.分类.第3部分:未增塑聚氯乙烯(PVC-U)、高冲击强度聚氯乙烯(PVC-HI)和氯化聚氯 | Thermoplastic pipes - Resistance to liquid chemicals - Classification - Unplasticized poly(vinyl chloride) (PVC-U), high-impact poly(vinyl chloride) (PVC-HI) and chlorinated poly(vinyl chloride) (PVC-C) pipes |
| BS ISO 4433-4-1998 | 热塑性塑料管.耐液体化学制品.分类.第4部分:聚偏氟乙烯管 | Thermoplastics pipes - Resistance to liquid chemicals - Classification - Poly(vinylidene fluoride) (PVDF) pipes |
| BS ISO 4525-2003 | 金属镀层.塑料材料上的镍加铬电镀层 | Metallic coatings - Electroplated coatings of nickel plus chromium on plastics materials |
| BS ISO 4575-2007 | 塑料.聚氯乙烯糊料.使用赛佛尔斯(Severs)流变仪测定表观粘度 | Plastics - Poly(vinyl chloride) pastes - Determination of apparent viscosity using the Severs rheometer |
| BS ISO 5473-1997 | 橡胶或塑料涂层织物.耐挤压性测定 | Rubber or plastics-coated fabrics - Determination of crush resistance |
| BS ISO 5893-2002 | 橡胶和塑料的试验设备.拉伸、弯曲和压缩型（横动的速率）.规范 | Rubber and plastics test equipment - Tensile, flexural and compression types (constant rate of traverse) - Specification |
| BS ISO 6133-1998 | 橡胶和塑料制品.测定撕裂强度和粘合强度获得的多峰值图形分析 | Rubber and plastics - Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength |
| BS ISO 6452-2007 | 橡胶或塑料涂层织物.汽车内装饰材料雾气凝结特征的测定 | Rubber- or plastics-coated fabrics - Determination of fogging characteristics of trim materials in the interior of automobiles |
| BS ISO 6721-10-2001 | 塑料.动态机械性能的测定.使用平板振荡流变仪测定复合剪切粘度 | Plastics - Determination of dynamic mechanical properties - Complex shear viscosity using a parallel-plate oscillatory rheometer |
| BS ISO 6721-9-1997+A1-2007 | 塑料.动态机械性能的测定.拉伸振动.声脉冲传播法 | Plastics - Determination of dynamic mechanical properties - Tensile vibration - Sonic-pulse propagation method |
| BS ISO 7229-1997 | 橡胶或塑料涂层织物.透气性测量 | Rubber- or plastics-coated fabrics - Measurements of gas permeability |
| BS ISO 7425-1-2002 | 液压流体动力.弹性体塑料面密封件的汽缸.尺寸和公差.活塞密封汽缸 | Hydraulic fluid power - Housing for elastomer-energized, plastic-faced seals - Dimensions and tolerances - Piston seal housings |
| BS ISO 7425-2-2002 | 液压流体动力.弹性体塑料面密封件的汽缸.尺寸和公差.活塞杆密封汽缸 | Hydraulic fluid power - Housing for elastomer-energized, plastic-faced seals - Dimensions and tolerances - Rod seal housings |
| BS ISO 7617-1-2002 | 室内装饰用塑料涂覆织物.涂覆聚氯乙烯(PVC)的针织品规范 | Plastics-coated fabrics for upholstery - Specification for PVC-coated knitted fabrics |
| BS ISO 7628-2010 | 道路车辆.气力制动系统用热塑性塑料管 | Road vehicles - Thermoplastics tubing for air braking systems |
| BS ISO 8066-2-2001 | 汽车空调器用橡胶和塑料软管及软管配件.规范.冷却剂134a | Rubber and plastics hoses and hose assemblies for automotive air conditioning - Specification - Refrigerant 134a |
| BS ISO 8096-2005 | 雨衣用橡胶或塑料涂覆织物.规范 | Rubber- or plastics-coated fabrics for water resistant clothing - Specification |
| BS ISO 8296-2003 | 塑料.薄膜和薄板.湿润表面张力的测定 | Plastics - Film and sheeting - Determination of wetting tension |
| BS ISO 8331-2007 | 橡胶和塑料软管及软管组件. 选择、储存、使用和维修指南 | Rubber and plastics hoses and hose assemblies - Guidelines for selection, storage, use and maintenance |
| BS ISO 8584-1-1998 | 工业用承压热塑性塑料管.耐化学性系数和基本应力的测定.聚烯烃管 | Thermoplastics pipes for industrial applications under pressure - Determination of the chemical resistance factor and of the basic stress - Polyolefin pipes |
| BS ISO 8605-2001 | 玻璃纤维增强塑料.片状模塑料(SMC) .基础规范 | Textile-glass-reinforced plastics - Sheet moulding compound (SMC) - Basis for specification |
| BS ISO 8660-2002 | 塑料.己内酰胺的高锰酸盐吸收指数的侧定.光谱分析法 | Plastics - Determination of permanganate absorption number of caprolactam - Spectrometric method |
| BS ISO 871-2006 | 塑料.热空气炉的点燃温度的测定 | Plastics - Determination of ignition temperature using a hot-air furnace |
| BS ISO 9370-1997 | 塑料制品.风化试验辐射暴露度的仪器测定.一般指南和基本试验方法 | Plastics - Instrumental determination of radiant exposure in weathering tests - General guidance and basic test method |
| BS ISO 974-2000 | 塑料.用冲击法测定脆性温度 | Plastics - Determination of the brittleness temperature by impact |
| BS ISO 9772-2001 | 泡沫塑料.小火焰小试样的水平燃烧特性的测定 | Cellular plastics - Determination of horizontal burning characteristics of small specimens subjected to a small flame |
| BS ISO 9911-2006 | 农业灌溉设备.手工操作小型塑料阀门 | Agricultural irrigation equipment - Manually operated small plastics valves |
| BS ISO 9988-1-2004 | 塑料.聚甲醛模塑和挤塑材料.命名体系和基本规范 | Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Designation system and basis for specifications |
| BS ISO/TR 5659-3-2000 | 塑料.烟雾的产生.用动态流动方法对光密度进行测定 | Plastics - Smoke generation - Determination of optical density by a dynamic flow method |
| BS PAS 003-1994 | 有塑料插座开起杆的不可再布线的13A插头 | Non-rewireable 13 A plugs with plastic socket shutter opening pins |
| BS PAS 103-2004 | 收集的废塑料的包装.用于再循环的收集和制备的良好规程指南和质量规范 | Collected waste plastics packaging - Specification for quality and guidance for good practice in collection and preparation for recycling |
| BS PAS 25-1999 | 行人区域的水井和人孔顶部用塑料框架 | Plastics frames for use in gully tops and manhole tops for pedestrian areas |
| DD ENV 13130-4-1999 | 与食品接触的材料和物品.限制使用的塑料材料. 塑料1,3丁二烯的测定 | Materials and articles in contact with foodstuffs. Plastics substances subject to limitation. Determination of 1,3-butadiene in plastics |
| DD ENV 13130-5-1999 | 与食品接触的材料和物品.限制使用的塑料材料.食品模拟物二氯乙烯的测定 | Materials and articles in contact with foodstuffs. Plastics substances subject to limitation. Determination of vinylidene chloride in food simulants |
| DD ENV 13130-7-1999 | 与食品接触的材料和物品.限制使用的塑料材料.食品模拟物单乙二醇和双乙二醇的测定 | Materials and articles in contact with foodstuffs. Plastics substances subject to limitation. Determination of monoethylene glycol and diethylene glycol in food simulants |
| DD ENV 1329-2-2001 | 建筑物内粪水和废物排放的塑料管道系统(低温和高温).未增塑聚氯乙烯（PVC－U）.符合性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Guidance for the assessment of conformity |
| DD ENV 13801-2001 | 建筑物内土壤和废物排放用塑料管道系统(低和高温).热塑性.安装推荐方法 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Thermoplastics. Recommended practice for installation |
| DD ENV 1401-3-2001 | 非压力地下废水和排水系统的塑料管道系统.非增塑聚氯乙烯（PVC－U）.安装指南 | Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinylchloride) (PVC-U). Guidance for installation |
| DD ENV 1452-7-2001 | 供水用塑料管道系统.未增塑聚氯乙烯.合格评定指南 | Plastics piping systems for water supply. Unplasticized poly(vinyl chloride) (PVC-U). Guidance for the assessment of conformity |
| DD ENV 1453-2-2001 | 建筑物内的粪水和废物排放用的带结构壁管道的塑料管道系统（低温和高温）.非增塑聚氯乙烯.一致性评价指南 | Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings. Unplasticized poly(vinyl chloride) (PVC-U). Guidance for the assessment of conformity |
| DD ENV 1519-2-2001 | 建筑物内土壤和废物排放的塑料管道系统(低温和高温).聚乙烯.符合性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE). Guidance for the assessment of conformity |
| DD ENV 1565-2-2001 | 建筑结构内低温和高温粪水和废物排放的塑料管道系统.苯乙烯共聚物.符合性评价指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Styrene copolymer blends (SAN + PVC). Guidance for the assessment of conformity |
| DD ENV 1566-2-2001 | 建筑结构内低温和高温土壤和废物排放的塑料管道系统.聚氯乙烯.一致性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C). Guidance for the assessment of conformity |
| 编号 | 中文名称 | 英文名称 |