| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| DD ENV 12108-2001 | 塑料管道系统.建筑物内部的人用冷热水压力管道系统的安装指南 | Plastics piping systems. Guidance for the installation inside buildings of pressure systems for hot and cold water intended for human consumption |
| DD ENV 13130-6-1999 | 与食品接触的材料和物品.限制使用的塑料材料.塑料二氯乙烯的测定 | Materials and articles in contact with foodstuffs. Plastics substances subject to limitation. Determination of vinylidene chloride in plastics |
| DD ENV 1451-2-2001 | 建筑物内粪水和废物排放的塑料管道系统(低温和高温).聚丙烯.符合性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP). Guidance for the assessment of conformity |
| DD ENV 1455-2-2001 | 建筑物内粪和废物排放的塑料管道系统(低温和高温).丙烯腈-丁二烯-苯乙烯共聚物.符合性评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Acrylonitrile-butadiene- styrene (ABS). Guidance for the assessment of conformity |
| EN 1013-1-1997 | 单层顶盖用透光齿形塑料板 第1部分：一般要求和试验方法 | Light transmitting profiled plastic sheeting for single skin roofing - Part 1: General requirements and test methods |
| EN 1013-2-1998 | 单层顶盖用透光齿形塑料板 第2部分：玻璃纤维增强的聚脂树脂薄板的特殊要求和试验方法 | Light transmitting profiled plastic sheeting for single skin roofing - Part 2: Specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP) |
| EN 1013-3-1997 | 单层顶盖用透光齿形塑料板 第3部分：聚氯乙烯板的特殊要求和试验方法 | Light transmitting profiled plastic sheeting for single skin roofing - Part 3: Specific requirements and test methods for sheets of polyvinyl chloride (PVC) |
| EN 1013-4-2000 | 单层顶盖用透光齿形塑料板 第4部分：聚碳酸酯板的特殊要求、试验方法和性能 | Light transmitting profiled plastic sheeting for single skin roofing - Part 4: Specific requirements, test methods and performance of polycarbonate (PC) sheets |
| EN 1013-5-2000 | 单层顶盖用透光齿形塑料板 第5部分：聚甲基丙烯酸甲酯板的特殊要求、试验方法和性能 | Light transmitting profiled plastic sheeting for single skin roofing - Part 5: Specific requirements, test methods and performance of polymethylmethacrylate (PMMA) sheets |
| EN 1053-1995 | 塑料管道系统 无压力情况下使用的热塑管道系统 水密封性的试验方法 | Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness |
| EN 1054-1995 | 塑料管道系统 粪便和污水排放用热塑管道系统 连接件气密性试验方法 | Plastics piping systems - Thermoplastics piping systems for soil and waste discharge - Test method for airtightness of joints |
| EN 1055-1996 | 塑料管道系统 建筑物内粪便和污水排放用热塑管道系统 抗周期性升温的试验方法 | Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling |
| EN 1107-2-2001 | 防水柔性板 尺寸稳定性的测定 第2部分：屋顶防水用塑料和橡胶层 | Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN 1114-1-1996 | 橡胶和塑料机械 挤压机和挤压工作线 第1部分：挤压的安全要求 | Rubber and plastics machines - Extruders and extrusion lines - Part 1: Safety requirements for extruders |
| EN 1114-2-1998 | 橡胶和塑料机械 挤压机和挤压工作线 第2部分：冲模表面造粒机的安全要求 | Rubber and plastics machines - Extruders and extrusion lines - Part 2: Safety requirements for die face pelletisers |
| EN 1114-3-2001 | 橡胶和塑料机械 挤压机和挤压工作线 第3部分：压出机的安全要求 | Rubber and plastics machines - Extruders and extrusion lines - Part 3: Safety requirements for haul-offs |
| EN 1115-1-1997 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第1部分：概述 | Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 1: General |
| EN 1115-3-1996 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第3部分：配件 | Plastics piping systems for underground drainage and sewerage under pressure - Glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings |
| EN 1115-5-1996 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第5部分：连接 | Plastics piping systems for underground drainage and sewerage under pressure - Glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints |
| EN 1119-1996 | 塑料管道系统 玻璃增强热固塑料管和配件用接头 挠性和还原接合接头密封性和耐损伤性试验方法 | Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of flexible and reduced-articulation joints |
| EN 1120-1996 | 塑料管道系统 玻璃增强热固塑料管和配件 偏斜条件下内部一个截面耐化学品侵袭的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of a section in a deflected condition |
| EN 1122-2001 | 塑料 镉的测定 湿分解法 | Plastics - Determination of cadmium - Wet decomposition method |
| EN 1186-1-2002 | 与食品接触的材料和物品 塑料 第1部分：全部转移的条件和试验方法选择指南 | Materials and articles in contact with foodstuffs - Plastics - Part 1: Guide to the selection of conditions and test methods for overall migration |
| EN 1186-10-2002 | 与食品接触的材料和物品 塑料 第10部分：全部转移到橄榄油中的试验方法（用于橄榄油不完全萃取情况发生时 | Materials and articles in contact with foodstuffs - Plastics - Part 10: Test methods for overall migration into olive oil (modified method for use in case where incomplete extraction of olive oil occurs) |
| EN 1186-11-2002 | 与食品接触的材料和物品 塑料 第11部分：全部转移到C标签的合成甘油三酸脂混合物的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 11: Test methods for overall migration into mixtures of C-labelled synthetic triglycerides |
| EN 1186-12-2002 | 与食品接触的材料和物品 塑料 第12部分：低温时全部转移的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 12: Test methods for overall migration at low temperatures |
| EN 1186-13-2002 | 与食品接触的材料和物品 塑料 第13部分：高温时全部转移的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 13: Test method for overall migration at high temperatures |
| EN 1186-14-2002 | 与食品接触的材料和物品 塑料 第14部分：使用试验媒体异辛烷和95%乙醇从与脂肪食品接触的塑料全部转移的 | Materials and articles in contact with foodstuffs - Plastics - Part 14: Test methods for "substitute tests" for overall migration from plastics intended to come into contact with fatty foodstuffs using test media iso-octane and 95 % ethanol |
| EN 1186-15-2002 | 与食品接触的材料和物品 塑料 第15部分：用快速萃取到异辛烷和/或95%乙醇的方法进行转移到脂肪食品模拟装 | Materials and articles in contact with foodstuffs - Plastics - Part 15: Alternative test methods to migration into fatty food simulants by rapid extraction into iso-octane and/or 95% ethanol |
| EN 1186-2-2002 | 与食品接触的材料和物品 塑料 第2部分：全浸入法全部转移到橄榄油中的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 2: Test methods for overall migration into olive oil by total immersion |
| EN 1186-3-2002 | 与食品接触的材料和物品 塑料 第3部分：全浸入法全部转移到含水食品模拟装置中的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 3: Test methods for overall migration into aqueous food simulants by total immersion |
| EN 1186-4-2002 | 与食品接触的材料和物品 塑料 第4部分：细胞法全部转移到橄榄油中的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 4: Test methods for overall migration into olive oil by cell |
| EN 1186-5-2002 | 与食品接触的材料和物品 塑料 第5部分：细胞法全部转移到含水食品模拟装置中的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 5: Test methods for overall migration into aqueous food simulants by cell |
| EN 1186-6-2002 | 与食品接触的材料和物品 塑料 第6部分：使用一个小袋全部转移到橄榄油中的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 6: Test methods for overall migration into olive oil using a pouch |
| EN 1186-7-2002 | 与食品接触的材料和物品 塑料 第7部分：使用一个小袋全部转移到含水食品模拟装置中的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 7: Test methods for overall migration into aqueous food simulants using a pouch |
| EN 1186-8-2002 | 与食品接触的材料和物品 塑料 第8部分：物品填充法全部转移到橄榄油中的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 8: Test methods for overall migration into olive oil by article filling |
| EN 1186-9-2002 | 与食品接触的材料和物品 塑料 第9部分：物品填充法全部转移到含水食品模拟装置中的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 9: Test methods for overall migration into aqueous food simulants by article filling |
| EN 12012-1-2000 | 橡胶和塑料加工机械 粉碎机 第1部分：对刀片式制粒机的安全要求 | Rubber and plastics machines - Size reduction machines - Part 1: Safety requirements for blade granulators |
| EN 12012-2-2001 | 橡胶和塑料加工机械 粉碎机 第2部分：带式成球机的安全要求 | Rubber and plastics machines - Size reduction machines - Part 2: Safety requirements for strand pelletisers |
| EN 12012-3-2001 | 橡胶和塑料加工机械 粉碎机 第3部分：对撕碎机的安全要求 | Rubber and plastics machines - Size reduction machines - Part 3: Safety requirements for shredders |
| EN 12013-2000 | 橡胶和塑料加工机械 内部混合机 安全要求 | Rubber and plastics machines - Internal mixers - Safety requirements |
| EN 12061-1999 | 塑料管道系统 热塑性管件 耐冲击试验方法 | Plastics piping systems - Thermoplastics fittings - Test method for impact resistance |
| EN 12095-1997 | 塑料管道系统 雨水管道系统用托架 托架强度的试验方法 | Plastics piping systems - Brackets for rainwater piping systems - Test method for bracket strength |
| EN 12099-1997 | 塑料管道系统 聚乙烯管材和组件 挥发含量的测定 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| EN 12100-1997 | 塑料管道系统 聚乙稀(PE)阀门 支架间抗弯曲性的试验方法 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports |
| EN 12106-1997 | 塑料管道系统 聚乙稀(PE)管 压出后抗内压性的试验方法 | Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off |
| EN 12107-1997 | 塑料管道系统 压注热塑管件、阀门和辅助设备 管道组件压注用热塑 材料的长期液压强度的测定 | Plastics piping systems - Injection-moulded thermoplastics fittings, valves and ancillary equipment - Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components |
| EN 12117-1997 | 塑料管道系统 热塑管件、阀门和配件 气流速率/压降之间关系的测定 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| EN 12118-1997 | 塑料管道系统 用库仑计测定热塑性塑料中水分 | Plastics piping systems - Determination of moisture content in thermoplastics by coulometry |
| EN 12119-1997 | 塑料管道系统 聚乙烯(PE)阀门 抗热循环测试方法 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling |
| EN 12200-1-2000 | 地面上外部使用的塑料雨水管道系统 未增塑聚乙烯（聚氯乙烯）（PVC-U） 第1部分：管道、配件和系统用规范 | Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| EN 12201-1-2003 | 供水系统用塑料管道系统 聚乙烯（PE） 第1部分：总则 | Plastics piping systems for water supply - Polyethylene (PE) - Part 1: General |
| EN 12201-2-2003 | 供水系统用塑料管道系统 聚乙烯（PE） 第2部分：管道 | Plastics piping systems for water supply - Polyethylene (PE) - Part 2: Pipes |
| EN 12201-3-2003 | 供水系统用塑料管道系统 聚乙烯（PE） 第3部分：配件 | Plastics piping systems for water supply - Polyethylene (PE) - Part 3: Fittings |
| EN 12201-4-2001 | 供水系统用塑料管道系统 聚乙烯（PE） 第4部分：阀门 | Plastics piping systems for water supply - Polyethylene (PE) - Part 4: Valves |
| EN 12201-5-2003 | 供水系统用塑料管道系统 聚乙烯（PE） 第5部分：系统目的的适配性 | Plastics piping systems for water supply - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 1225-1996 | 塑料管道系统 玻璃增强热固性塑料管 潮湿条件下蠕变因子的测定和长期特定环刚度的计算 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under wet conditions and calculation of the long-term specific ring stiffness |
| EN 12256-1998 | 塑料管道系统 .热塑性塑料配件 装配式配件机械强度或挠度的试验方法 | Plastics piping systems - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings |
| EN 1226-1996 | 塑料管道系统 玻璃增强热固性塑料管 验证初期环状物挠曲阻力的试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection |
| EN 1227-1997 | 塑料管道系统 玻璃增强热固性塑料管 潮湿条件下长期最终相关环状物挠曲的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term ultimate relative ring deflection under wet conditions |
| EN 1228-1996 | 塑料管道系统 玻璃增强热固性塑料管 初始特定环刚度的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness |
| EN 12280-1-1997 | 橡胶或塑料涂覆织物 加速老化试验 第1部分：热老化 | Rubber- or plastics-coated fabrics - Accelerated ageing tests - Part 1: Heat ageing |
| EN 12280-2-2002 | 橡胶或塑料涂覆织物 加速老化试验 第2部分： 自然老化：光的影响或风化 | Rubber- or plastics-coated fabrics - Accelerated ageing tests - Part 2: Physical ageing: effect of light or weathering |
| EN 12280-3-2002 | 橡胶或塑料涂覆织物 加速老化试验 第3部分：环境老化 | Rubber- or plastics-coated fabrics - Accelerated ageing tests - Part 3: Environmental ageing |
| EN 1229-1996 | 塑料管道系统 玻璃增强热固性塑料管 验证短期内部压力下墙的密封性试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure |
| EN 12293-1999 | 塑料管道系统 热水和冷水用热塑性塑料管道和接头 安装组件耐热循环性的试验方法 | Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling |
| EN 12294-1999 | 塑料管道系统 热水和冷水系统 真空下气密性的试验方法 | Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum |
| EN 12295-1999 | 塑料管道系统 热水和冷水用热塑性塑料管道和接头 接合处耐压力循环试验方法 | Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling |
| EN 12301-2000 | 橡胶和塑料机械 砑光机 安全要求 | Rubber and plastics machines - Calenders - Safety requirements |
| EN 12310-2-2000 | 挠性防水板 抗性测定 第2部分：塑料和橡胶屋面防水板 | Flexible sheets for waterproofing - Determination of resistance to tearing - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN 12311-2-2000 | 挠性防水板 拉伸性能的测定 第2部分：塑料和橡胶屋面防水板 | Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN 12316-2-2000 | 挠性防水板 结合处抗裂性的测定 第2部分：塑料和橡胶屋面防水板 | Flexible sheets for waterproofing - Determination of peel resistance of joints - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN 12317-2-2000 | 挠性防水板 结合处抗剪切性的测定 第2部分：塑料和橡胶屋面防水板 | Flexible sheets for waterproofing - Determination of shear resistance of joints - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN 12332-1-1998 | 橡胶或塑料涂覆织物 脆裂强度的测定 第1部分：钢球法 | Rubber or plastic coated fabrics - Determination of bursting strength - Part 1: Steel ball method |
| EN 12332-2-2002 | 橡胶或塑料涂覆织物 脆裂强度的测定 第2部分：静压法 | Rubber- or plastic-coated fabrics - Determination of bursting strength - Part 2: Hydraulic method |
| EN 12409-1999 | 橡胶和塑料机械 热成形机 安全要求 | Rubber and plastics machines - Thermoforming machines - Safety requirements |
| EN 1254-3-1998 | 铜和铜合金 管件 第3部分：塑料管用压接端头管件 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| EN 12573-1-2000 | 静态无压焊接热塑料罐 第1部分：概述 | Welded static non-pressurized thermoplastic tanks - Part 1: General principles |
| EN 12573-2-2000 | 静态无压焊接热塑料罐 第2部分：立式圆筒罐的计算 | Welded static non-pressurized thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanks |
| EN 12573-3-2000 | 静态无压焊接热塑料罐 第3部分：单层矩形罐的设计和计算 | Welded static non-pressurized thermoplastic tanks - Part 3: Design and calculation for single skin rectangular tanks |
| EN 12573-4-2000 | 静态无压焊接热塑料罐 第4部分：法兰接头的设计和计算 | Welded static non-pressurized thermoplastic tanks - Part 4: Design and calculation of flanged joints |
| EN 12575-1998 | 塑料 热固模塑物料 SMC中纤维浸湿程度的测定 | Plastics - Thermoset moulding compounds - Determination of the degree of fibre wet out in SMC |
| EN 12576-1998 | 塑料 纤维增强复合物 SMC、BMC和DMC的压缩模制试验板的制备 | Plastics - Fibre reinforced composites - Preparation of compression moulded test plates of SMC, BMC and DMC |
| EN 12613-2001 | 具有可视特性的地下电缆和管线用塑料报警装置 | Plastics warning devices for underground cables and pipelines with visual characteristics |
| EN 12691-2001 | 防水软薄板 屋面防水用沥青、塑料和橡胶薄板 抗冲击性能测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to impact |
| EN 12707-1999 | 塑料桶 公称容量为210升、220升和225升的非移动头式(敞口)桶 | Plastics drums - Non-removable head (tight head) drums with a nominal capacity of 210 l, 220 l and 225 l |
| EN 12708-2000 | 公称容量为20升至225升的塑料容器用塞/盖封闭系统 | Plug/bung closure systems for plastics containers with a nominal capacity of 20 l to 225 l |
| EN 12709-2000 | 塑料桶 标称容量20升到120升的非移动头（敞口）桶 | Plastics drums - Non-removable head (tight head) circular cross-section drums with a nominal capacity of 20 l to 120 l |
| EN 12712-2000 | 塑料汽油筒 托板为800mm1200mm、1000mm1200mm和1140mm1140mm的最大公称容量为20升至60升的塑料油 | Plastics jerricans - Jerricans with a nominal capacity of 20 l to 60 l for optimal utilization of pallet sizes 800 mm x 1200 mm, 1000 mm x 1200 mm and 1140 mm x 1140 mm |
| EN 12713-2000 | 公称容积20升至60升的塑料容器用螺旋帽闭合系统 | Screw cap closure systems for plastics containers with a nominal capacity of 20 l to 60 l |
| EN 12714-2000 | 塑料柱桶 额定容量为25升至220升的可移动头(开口)桶 | Plastics drums - Removable head (open head) drums with a nominal capacity of 25 l to 220 l |
| EN 12730-2001 | 防水软薄板 屋面防水用沥青 塑料和橡胶薄板 抗静负荷性能的测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to static loading |
| EN 12759-2001 | 涂橡胶或塑料涂织物 耐液体性能 | Rubber- or plastic-coated fabrics - Determination of resistance to liquids |
| EN 1277-1996 | 塑料管道系统 地下无压用热塑管道系统 弹性密封环型接头密封性试验方法 | Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints |
| EN 12814-1-1999+AC-2003 | 热塑性塑料半成品的焊接接头试验 第1部分：弯曲试验 | Testing of welded joints of thermoplastics semi-finished products - Part 1: Bend test |
| EN 12814-2-2000 | 热塑性塑料半成品的焊接接头试验 第2部分：拉伸试验 | Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test |
| EN 12814-3-2000 | 热塑性塑料半成品的焊接接头试验 第3部分：拉伸蠕变试验 | Testing of welded joints of thermoplastics semi-finished products - Part 3: Tensile creep test |
| EN 12814-4-2001 | 热塑性塑料半成品的焊接接头试验 第4部分：剥落试验 | Testing of welded joints of thermoplastics semi-finished products - Part 4: Peel test |
| EN 12814-5-2000 | 热塑性塑料半成品的焊接接头试验 第5部分：目测 | Testing of welded joints of thermoplastics semi-finished - Part 5: Macroscopic examination |
| EN 12814-6-2000 | 热塑性塑料半成品的焊接接头试验 第6部分：低温拉伸试验 | Testing of welded joints of thermoplastics semi-finished products - Part 6: Low temperature tensile test |
| EN 12814-7-2002 | 热塑性塑料半成品的焊接接头试验 第7部分：采用腰形试样的拉伸试验 | Testing of welded joints of thermoplastics semi-finished products - Part 7: Tensile test with waisted test specimens |
| EN 12814-8-2001+AC-2003 | 热塑性塑料半成品的焊接接头试验 第8部分：要求 | Testing of welded joints of thermoplastics semi-finished products - Part 8: Requirements |
| EN 12877-1-1999 | 塑料中的着色剂 塑料中着色剂处理过程中耐热颜色稳定性的测定 第1部分：概述 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 1: General introduction |
| EN 12877-2-1999 | 塑料中的着色剂 塑料中着色剂处理过程中耐热颜色稳定性的测定 第2部分：注模法测定 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 2: Determination by injection moulding |
| EN 12877-3-1999 | 塑料中的着色剂 塑料中着色剂处理过程中耐热颜色稳定性的测定 第3部分：加热试验法测定 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 3: Determination by oven test |
| EN 12877-4-1999 | 塑料中的着色剂 塑料中着色剂处理过程中耐热颜色稳定性的测定 第4部分：双辊研磨法测定 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 4: Determination by two-roll milling |
| EN 12943-1999 | 热塑性塑料用填料 范围、名称、要求和试验 | Filler materials for thermoplastics - Scope, designation, requirements, tests |
| EN 1296-2000 | 屋顶材料的防水挠性薄板、 沥青、塑料和橡胶薄板 长时间暴露在高湿环境下的天然老化方法 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roofing - Method of artificial ageing by long term exposure to elevated temperature |
| EN 13029-2001 | 包装 轻薄金属包装 插入式塑料封闭开口 | Packaging - Light-gauge metal packaging - Apertures for plug-in plastic closures |
| EN 13045-2000 | 包装 挠性柱形塑料管 尺寸和公差 | Packaging - Flexible cylindrical plastic tubes - Dimensions and tolerances |
| EN 13067-2003 | 塑料焊接人员 焊工资质测试 热塑性塑料焊接组件 | Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies |
| EN 13100-1-1999 | 热塑性塑料半成品焊接接头的无损检验 第1部分：外观检查 | Non destructive testing of welded joints of thermoplastics semi-finished products - Part 1: Visual examination |
| EN 13117-1-2000 | 运输包装 可再用刚性塑料分配箱 第1部分：一般应用 | Transport packaging - Reusable, rigid plastics distribution boxes - Part 1: General purpose application |
| EN 13117-2-2000 | 运输包装 可再用刚性塑料分配箱 第2部分：通用测试规范 | Transport packaging - Reusable, rigid plastics distribution boxes - Part 2: General specifications for testing |
| EN 13164-2001 | 建筑物保温制品 工厂预制挤压泡沫塑料（XPS）制品 规范 | Thermal insulation products for buildings - Factory made products of extruded polystyrene foam (XPS) - Specification |
| EN 13244-1-2002 | 地上和地下给排水和污水压力系统用塑料管道 聚已烯（PE） 第1部分：总则 | Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General |
| EN 13244-2-2002 | 地上和地下给排水和污水压力系统用塑料管道 聚已烯（PE） 第2部分：管道 | Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes |
| EN 13244-3-2002 | 地上和地下给排水和污水压力系统用塑料管道 聚已烯（PE） 第3部分：配件 | Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings |
| EN 13244-4-2002 | 地上和地下给排水和污水压力系统用塑料管道 聚已烯（PE） 第4部分：阀门 | Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 4: Valves |
| EN 13244-5-2002 | 地上和地下给排水和污水压力系统用塑料管道 聚已烯（PE） 第5部分：系统适用度 | Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 1329-1-1999 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 硬塑聚氯乙烯(PVC-U) 第1部分：管材、管件和系统规 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| EN 13360-2002 | 橡胶或塑料涂层织物 术语 | Rubber- or plastics-coated fabrics - Terminology |
| EN 13416-2001 | 挠性防水板 沥青、塑料和橡胶屋面防水板 取样规则 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Rules for sampling |
| EN 13566-1-2002 | 用于修复非压力排水和污水网的塑料管道系统 第1部分：总则 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General |
| EN 13566-3-2002 | 用于修复非压力排水和污水网的塑料管道系统 第3部分：带密装配管的衬套 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes |
| EN 13566-4-2002 | 用于修复非压力排水和污水网的塑料管道系统 第4部分：带现场固化管的衬套 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes |
| EN 13583-2001 | 挠性防水板 沥青、塑料和橡胶屋面防水板 抗冰雹能力测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of hail resistance |
| EN 13592-2003 | 收集家庭废物用塑料袋 类型、要求和试验方法 | Plastics sacks for household waste collection - Types, requirements and test methods |
| EN 13598-1-2003 | 非压力底下排水和污水塑料管道系统 非增塑聚氯乙烯（PVC-U）、聚丙烯（PP）和聚乙烯（PE） 第1部分：包括 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers |
| EN 13655-2002 | 塑料 农业和园艺中使用的热塑性覆盖膜 | Plastics - Mulching thermoplastic films for use in agriculture and horticulture |
| EN 13689-2002 | 用于修复的塑料管道系统的分类和设计指南 | Guidance on the classification and design of plastics piping systems used for renovation |
| EN 13706-1-2002 | 加强塑料复合材料 拉伸型材规范 第1部分：命名 | Reinforced plastic composites - Specification for pultruded profiles - Part 1: Designation |
| EN 13706-2-2002 | 加强塑料复合材料 拉伸型材规范 第2部分：试验方法和一般要求 | Reinforced plastic composites - Specification for pultruded profiles - Part 2: Methods of test and general requirements |
| EN 13706-3-2002 | 加强塑料复合材料 拉伸型材规范 第3部分：特殊要求 | Reinforced plastic composites - Specification for pultruded profiles - Part 3: Specific requirements |
| EN 13887-2003 | 建筑粘合剂 粘结之前金属和塑料表面制备指南 | Structural adhesives - Guidelines for surface preparation of metals and plastics prior to adhesive bonding |
| EN 13900-1-2003 | 颜料和补充剂 塑料中扩散方法和扩散特性的评估 第1部分：一般介绍 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 1: General introduction |
| EN 13900-2-2003 | 颜料和补充剂 塑料中扩散方法和扩散特性的评估 第2部分：通过二辊研磨法测定塑化聚氯乙烯中的着色性和易 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 2: Determination of colouristic properties and ease of dispersion in plasticized polyvinylchloride by two-roll milling |
| EN 13900-3-2003 | 颜料和补充剂 塑料中扩散方法和扩散特性的评估 第3部分：通过二辊研磨法测定聚乙烯中的着色性和黑色及颜 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 3: Determination of colouristic properties and ease of dispersion of black and colour pigments in polyethylene by two-roll milling |
| EN 1393-1996+AC-1997 | 塑料管道系统 玻璃增强热固性塑料(GRP)管 初始径向拉伸特性的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial longitudinal tensile properties |
| EN 1394-1996+AC-1997 | 塑料管道系统 玻璃增强热固性塑料(GRP)管 外观初始圆周抗拉强度的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength |
| EN 13972-2002 | 刚性塑料容器 标称容量 满容量和总容量的定义以及满容量和总容量的测定 | Rigid plastics containers - Definition of nominal, brimful and total capacity and measurement of brimful and total capacity |
| EN 13973-2002 | 刚性塑料容器 排水能力的测定方法 | Rigid plastics containers - Method for determination of drainability |
| EN 13974-2002 | 刚性塑料容器 尺寸、重量和容积的元差规范 | Rigid plastics containers - Specification of tolerance for dimensions, weight and volume |
| EN 1401-1-1998 | 非压力地下雨水管和污水管用塑料管道系统未增塑聚氯乙烯(PVC-U) 管道 第1部分：配件和系统规范 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| EN 1411-1996 | 塑料管道和导管系统 热塑管 用阶梯法测定抗外冲击能力 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of resistance to external blows by the staircase method |
| EN 1417-1996 | 橡胶和塑料加工机器 双辊式破碎机 安全要求 | Rubber and plastics machines - Two roll mills - Safety requirements |
| EN 14233-2002 | 与食物接触的材料和物品 塑料 为进行迁移试验选择适当温度在微波炉或传统炉加热过程中，塑料/食物接触面 | Materials and articles in contact with foodstuffs - Plastics - Determination of temperature of plastics materials and articles at the plastics/food interface during microwave and conventional oven heating in order to select the appropriate temperature fo |
| EN 1437-2002 | 塑料管道系统 地下排水和污水用管道系统 耐温度循环和外部负荷综合作用的试验方法 | Plastics piping systems - Piping systems for underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading |
| EN 1446-1996 | 塑料管道及导管系统 热塑管 环挠形测定 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility |
| EN 1447-1996 | 塑料管道系统 玻璃增强热固性塑料管 (GRP) 长期耐内压能力的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure |
| EN 1448-1996 | 塑料管道系统 玻璃增强热固塑料(GRP)组件 带弹性密封件的刚性锁紧插承接合的设计查验试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of rigid locked socket-and-spigot joints with elastomeric seals |
| EN 14481-2003 | 与食品接触的材料和物品 塑料 油脂接触的测定试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for the determination of fatty contact |
| EN 1449-1996 | 塑料管道系统 玻璃纤维增强热固性塑料(GRP)组件 查检水泥套管插承接合设计的试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of cemented socket-and-spigot joints |
| EN 1450-1996+A1-1998 | 塑料管道系统 玻璃增强热固塑料(GRP)组件 螺栓法兰连接的设计查验试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of bolted flange joints |
| EN 1451-1-1998 | 建筑物结构内污物和废水排出(低和高温)用塑料管道系统 聚丙烯(PP ) 第1部分：管材、管件和系统规范 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system |
| EN 1452-1-1999 | 供水塑料管道系统 硬聚氯乙烯(PVC-U) 第1部分：总则 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General |
| EN 1452-2-1999 | 供水塑料管道系统 硬聚氯乙烯(PVC-U) 第2部分：管材 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes |
| EN 1452-3-1999 | 供水塑料管道系统 硬聚氯乙烯(PVC-U) 第3部分：管件 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings |
| EN 1452-4-1999 | 供水塑料管道系统 硬聚氯乙烯(PVC-U) 第4部分：阀门和附属设备 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment |
| EN 1452-5-1999 | 供水塑料管道系统 硬塑聚氯乙烯(PVC-U) 第5部分：系统的适合性 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5: Fitness for purpose of the system |
| EN 1453-1-2000 | 建筑物内污物和废水排放(低和高温)带结构壁管道的塑料管道系统 硬聚氯乙烯(PVC-U) 第1部分：管材和系统规 | Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system |
| EN 1455-1-1999 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 丙烯腈 丁二烯 苯乙烯共聚物 第1部分：管材、管 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system |
| EN 1456-1-2001 | 地上和地下污废水压力排放用塑料管道系统 硬已烯(聚氯已烯)(PVC-U) .第1部分：管道组件和系统规范 | Plastics piping systems for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for piping components and the system |
| EN 1519-1-1999 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 聚乙烯(PE) 第1部分：管材、管件和系统规范 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| EN 1555-1-2002 | 供给气体燃料用塑料管道系统 聚已烯(PE) 第1部分：总则 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 1555-2-2002 | 供给气体燃料用塑料管道系统 聚已烯(PE) 第2部分：管材 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| EN 1555-3-2002 | 供给气体燃料用塑料管道系统 聚已烯(PE) 第3部分：管件 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| EN 1555-4-2002 | 供给气体燃料用塑料管道系统 聚已烯(PE) 第4部分：阀门 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves |
| EN 1555-5-2002 | 供给气体燃料用塑料管道系统 聚已烯(PE) 第5部分：针对系统用途的适合性 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 1565-1-1998 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 苯乙烯共聚混合物(SAN+PVC) 第1部分：管材、管件和 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system |
| EN 1566-1-1998 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 氯化聚偏氯乙烯(PVC-C) 第1部分：管材、管件和系统 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system |
| EN 1612-1-1997 | 橡胶和塑料机械 反应模塑机械 第1部分：测量和混合装置的安全要求 | Rubber and plastics machines - Reaction moulding machines - Part 1: Safety requirements for metering and mixing units |
| EN 1612-2-2000 | 橡胶和塑料机械 反应模塑机械 第2部分：反应模压车间的安全要求 | Rubber and plastics machines - Reaction moulding machines - Part 2: Safety requirements for reaction moulding plant |
| EN 1636-3-1997 | 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第3部分：管件 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings |
| EN 1636-5-1997 | 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第5部分：针对接头 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints |
| EN 1636-6-1997 | 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第6部分：安装实践 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 6: Practices for installation |
| EN 1638-1997 | 塑料管道系统 玻璃增强热固塑料管道(GRP) 循环内压效果的试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method for the effects of cyclic internal pressure |
| EN 1680-1997 | 塑料管道系统 聚乙烯(PE)管道系统用阀门 传动装置的弯曲时和弯曲后密封性的试验方法 | Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanism |
| EN 1704-1997 | 塑料管道系统 热塑阀门 弯曲情况下温度周期变化后阀门完整性的试验方法 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after temperature cycling under bending |
| EN 1705-1996 | 塑料管道系统 热塑阀门 外部鼓风后阀门完整性试验方法 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow |
| EN 1716-1997 | 塑料管道系统 聚乙烯(PE)分接三通管 分接三通管组件上耐冲击能力的检测方法 | Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an assembled tapping tee |
| EN 1734-1996 | 橡胶或塑料涂覆织物 耐水渗透性的测定 低压法 | Rubber or plastics coated fabrics - Determination of resistance to water penetration - Low pressure method |
| EN 1735-1996 | 橡胶或塑料涂覆织物 挠性测定 | Rubber or plastics coated fabrics - Determination of flexibility |
| EN 1842-1997 | 塑料 热固模塑化合物(SMC-BMC).压制模缩测定 | Plastics - Thermoset moulding compounds (SMC - BMC) - Determination of compression moulding shrinkage |
| EN 1844-2001 | 防水热塑性及弹性薄板 耐臭氧性的测定 屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing |
| EN 1847-2001 | 挠性防水薄板 屋顶防水用塑料和橡胶薄板 暴露在液体化学品及水中的方法 | Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Methods for exposure to liquid chemicals, including water |
| EN 1848-2-2001 | 挠性防水薄板 长度、宽度和平直度的测定 第2部分：屋顶防水用塑料和橡胶板 | Flexible sheets for waterproofing - Determination of length, width, straightness and flatness - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN 1849-2-2001 | 挠性防水薄板 单位面积厚度和质量的测定 第2部分：屋顶防水用塑料和橡胶板 | Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN 1850-2-2001 | 挠性防水薄板 外观缺陷的测定 第2部分：屋顶防水用塑料和橡胶板 | Flexible sheets for waterproofing - Determination of visible defects - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN 1852-1-1997+A1-2001 | 无压地下排水和污水用塑料管道系统 聚丙烯(PP)、 第一部分：管材、管件及系统规范 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system |
| EN 1862-1997 | 塑料管道系统 玻璃增强热固塑料管(GRP) 暴露在化学环境后相关挠曲蠕变因素的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the relative flexural creep factor following exposure to a chemical environment |
| EN 1875-3-1997 | 橡胶塑料涂层织物 撕裂强度测定 第3部分：梯形法 | Rubber- or plastics-coated fabrics - Determination of tear strength - Part 3: Trapezoidal method |
| EN 1876-1-1997 | 橡胶或塑料涂层织物 低温试验 第1部分：弯曲试验 | Rubber or plastics-coated fabrics - Low-temperature tests - Part 1: Bending test |
| EN 1876-2-1997 | 橡胶或塑料涂层织物 低温试验 第2部分：循环撞击试验 | Rubber- or plastics-coated fabrics - Low temperature tests - Part 2: Impact test on loop |
| EN 1903-1999 | 粘合剂 地板或墙壁塑料或橡胶覆盖物用粘合剂的试验方法 加速老化后尺寸变化的测定 | Adhesives - Test method for adhesives for plastic or rubber floor coverings or wall coverings - Determination of dimensional changes after accelerated ageing |
| EN 1905-1998 | 塑料管道系统 硬聚氯乙烯管、管件和材料 基于氯的总含量评估聚氯乙烯含量的方法 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on total chlorine content |
| EN 1928-2000 | 防水挠性薄板 屋顶防水用沥青、 塑料和橡胶薄板 不透水性的测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of watertightness |
| EN 1931-2000+AC-2001 | 防水挠性薄板 屋顶防水用沥青 塑料和橡胶薄板 水蒸汽渗透特性的测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of water vapour transmission properties |
| EN 1979-1999 | 塑料管道和管道系统 热塑螺旋型结构壁的管材 接缝拉伸强度的测定 | Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam |
| EN 1989-2000 | 热塑性管道系统 埋地无压污水用接头 通过估计密封压力对热塑弹性塑料(TPE)密封接头的长时间密封性能的试 | Thermoplastics piping systems - Joints for buried non-pressure sewerage applications - Test method for long-term sealing performance of joints with thermoplastic elastomer (TPE) seals by estimating the sealing pressure |
| EN 201-1997+A1-2000 | 橡胶和塑料机械 注模机 安全要求 | Rubber and plastics machines - Injection moulding machines - Safety requirements |
| EN 233-1999 | 卷式墙面饰层 成品壁纸、聚乙烯和塑料墙面饰层规范 | Wallcoverings in roll form - Specification for finished wallpapers, wall vinyls and plastics wallcoverings |
| EN 2377-1989 | 航空航天系列 玻璃纤维增强塑料 试验方法 表观层间剪切强度测定 | Aerospace series - Glass fibre reinforced plastics - Test method - Determination of apparent interlaminar shear strength |
| EN 2378-1995 | 航空航天系列 纤维增强塑料 通过浸渍对吸水率的测定 | Aerospace series - Fibre reinforced plastics - Determination of water absorption by immersion |
| EN 2489-1995 | 航空航天系列 纤维增强塑料 试验液体影响的测定 | Aerospace series - Fibre reinforced plastics - Determination of the action of test fluids |
| EN 2561-1995 | 航空航天系列 碳纤维增强塑料 单向塑料层压制品 纤维方向平行抗拉试验 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Tensile test parallel to the fibre direction |
| EN 2562-1997 | 航空航天系列 碳纤维增强塑料 单向层压塑料 与纤维方向平行的弯曲试验 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Flexural test parallel to the fibre direction |
| EN 2563-1997 | 航空航天系列 碳纤维增强塑料 单向层压板 层间表面剪切强度的测定 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Determination of the apparent interlaminar shear strength |
| EN 2597-1998 | 航空航天系列 碳纤维增强塑料 单向叠层板材 垂直于纤维方向的拉伸试验 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Tensile test perpendicular to the fibre direction |
| EN 25978-1993 | 橡胶或塑料涂覆织物 耐粘结强度的测定 | Rubber- or plastics-coated fabrics; determination of blocking resistance (ISO 5978:1990) |
| EN 26801-1993 | 橡胶或塑料软管 容积膨胀的测定 | Rubber or plastics hoses-Determination of volumetric expansion (ISO 6801:1983) |
| EN 26802-1993 | 钢丝增强的橡胶和塑料软管及软管件 弯抗冲击试验 | Rubber and plastics hoses and hose assemblies, wire reinforced- Hydraulic impulse test with flexing (ISO 6802:1991) |
| EN 27326-1993 | 橡胶和塑料软管 静态条件下耐臭氧性的评定 | Rubber and plastics hoses-Assessment of ozone resistance under static conditions (ISO 7326:1991) |
| EN 2743-2001 | 航空航天系列 纤维增强塑料 测试材料未老化前调理的标准程序 | Aerospace series - Fibre reinforced plastics - Standard procedures for conditioning prior to testing unaged materials |
| EN 2746-1998 | 航空航天系列 玻璃纤维增强塑料 弯曲试验 三点弯曲法 | Aerospace series - Glass fibre reinforced plastics - Flexural test - Three point bend method |
| EN 2747-1998 | 航空航天系列 玻璃纤维增强塑料 抗拉试验 | Aerospace series - Glass fibre reinforced plastics - Tensile test |
| EN 28029-1993 | 塑料软管 通用型可折叠织物增强输水软管 规范 | Plastics hose-General purpose collapsible water hose, textile reinforced-Specification (ISO 8029:1985) |
| EN 28033-1993 | 橡胶和塑料软管 部件间粘合强度的测定 | Rubber and plastic hoses-Determination of adhesion between components (ISO 8033:1991) |
| EN 28233-1990 | 热塑性塑料阀门 扭矩 试验方法 | Thermoplastics valves- Torque; test method (ISO 8233:1988) |
| EN 28659-1990 | 热塑性塑料阀门 疲劳强度 试验方法 | Thermoplastic valves- Fatigue strength- Test method (ISO 8659:1989) |
| EN 289-1993 | 橡胶和塑料机械 压制和传递模制压力机 设计的安全要求 | Rubber and plastics machinery; compression and transfer moulding presses; safety requirements for the design |
| EN 301-1992 | 承重木结构用胶接酚醛塑料和氨基塑料 分类和性能要求 | Adhesives phenolic and aminoplastic, for load bearing timber structures - Classification and performance requirements |
| EN 422-1995 | 橡胶和塑料机械 安全 生产空心制品的吹模机械 设计和制造的要求 | Rubber and plastics machines - Safety - Blow moulding machines intended for the production of hollow articles - Requirements for the design and construction |
| EN 495-5-2000 | 防水用柔性板 低温下折叠性的测定 第5部分：屋顶防水用塑料和橡胶板 | Flexible sheets for waterproofing - Determination of foldability at low temperature - Part 5: Plastic and rubber sheets for roof waterproofing |
| EN 578-1993 | 塑料管道系统 塑料管和配件 不透明度的测定 | Plastics piping systems - Plastics pipes and fittings - Determination of the opacity |
| EN 579-1993 | 塑料管道系统 交联聚乙烯(PE-X)管 溶剂萃取法测定交联密度 | Plastics piping systems - rosslinked polyethylene (PE-X) pipes -Determination of degree of crosslinking by solvent extraction |
| EN 580-2003 | 塑料管道系统 未增塑聚氯乙烯(PVC-U)管 特定温度下耐二氯甲烷试验方法 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT) |
| EN 59-1977 | 玻璃纤维增强塑料 用 Barcol压痕方法测量硬度 | Glass reinforced plastics - Measurement of hardness by means of a Barcol impressor |
| EN 60674-1-1998 | 电工用塑料薄膜规范 第１部分：定义和一般要求 | Specification for plastic films for electrical purposes - Part 1: Definitions and general requirements (IEC 60674-1:1980) |
| EN 60674-2-1998+A1-2001 | 电气用塑料薄膜规格 第２部分：试验方法 | Specification for plastic films for electrical purposes - Part 2: Methods of test (IEC 60674-2:1988 + Corrigendum 1995) |
| EN 60674-3-1-1998 | 电工用塑料薄膜规范 第３部分：单项材料规范 活页１：电容器用双轴定向聚丙烯薄膜 | Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors (IEC 60674-3-1:1998) |
| EN 60674-3-2-1998 | 电气用塑料薄膜规格 第3部分：.专用材料的规格 活页2：对电气绝缘用平衡双轴定聚对苯二甲酸乙二醇酯薄膜 | Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Requirements for balanced biaxially oriented polyethylene terephthalate (PET) films used for electrical insulation (IEC 60674-3-2:1992) |
| EN 60674-3-3-1998 | 电气用塑料薄膜规格 第3部分：专用材料的规格 活页3：对电气绝缘用聚碳酸酯薄膜的要求 | Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 3: Requirements for polycarbonate (PC) films used for electrical insulation (IEC 60674-3-3:1992) |
| EN 60674-3-4 bis 6-1995 | 电气用塑料薄膜规格 第3部分：专用材料的规格 活页4至6：对电气绝缘用聚酰亚胺薄膜要求 | Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheets 4 to 6: Requirements for polyimide films used for electrical insulation (IEC 60674-3-4 to 6:1993) |
| EN 60674-3-7-1998 | 电气用塑料薄膜规格 第3部分：专用材料的规格 活页7：对电气绝缘用氟乙烯-丙烯薄膜的要求 | Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 7: Requirements for fluoroethylene-propylene (FEP) films used for electrical insulation (IEC 60674-3-7:1992) |
| EN 60749-20-2003 | 半导体器件 机械和气候试验方法 第20部分：用塑料封装的半导体磁场探测器对潮湿和焊热结合效应的阻抗 | Semiconductor devices - Mechanical and climatic test methods - Part 20: Resistance of plastic-encapsulated SMDs to the combined effect of moisture and soldering heat (IEC 60749-20:2002) / Note: Endorsement notice |
| EN 60749-31-2003 | 半导体器件 机械和气候试验方法 第31部分：用塑料封装设备的可燃性（内部导致的） | Semiconductor devices - Mechanical and climatic test methods - Part 31: Flammability of plastic-encapsulated devices (internally induced) (IEC 60749-31:2002) / Note: Endorsement notice |
| EN 60749-32-2003 | 半导体器件 机械和气候试验方法 第32部分：用塑料封装设备的可燃性（外部导致的） | Semiconductor devices - Mechanical and climatic test methods - Part 32: Flammability of plastic-encapsulated devices (externally induced) (IEC 60749-32:2002) / Note: Endorsement notice |
| EN 61234-1-1994 | 电气绝缘材料水解稳定性的试验方法 第1部分：塑料薄膜 | Method of test for the hydrolytic stability of electrical insulating materials- |
| EN 61837-1-1999 | 频率控制和选择用表面安装的压电器件 标准外形和端头连接 第1部分：塑料模压外壳外形 | Surface mounted piezoelectric devices for frequency control and selection - Standard outlines and terminal lead connections - Part 1: Plastic moulded enclosure outlines (IEC 61837-1:1999) |
| EN 62148-4-2003 | 光纤有源元件和器件 包装和接口标准 第4部分：PN 1X 9 塑料光纤收发机 | Fibre optic active components and devices - Package and interface standards - Part 4: PN 1*9 plastic optical fibre transceivers (IEC 62148-4:2003) / Note: Endorsement notice |
| EN 637-1994 | 塑料管道系统 玻璃增强塑料部件 用重量分析法测定成分含量 | Plastics piping systems - Glass-reinforced plastics components - Determination of the amounts of constituents using the gravimetric method |
| EN 705-1994 | 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管和配件 回归分析及其使用方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analysis and their use |
| EN 713-1993 | 塑料管道系统 配件和聚烯烃压力管间的机械接合件 弯曲时组件内部压力密封性的试验方法 | Plastic piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending |
| EN 727-1994 | 塑料管道和导管系统 热塑性管和配件 维卡（Vicat）软化温度（VST）的测定 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
| EN 728-1997 | 塑料管道和导管系统 聚烯烃管和配件 氧化感应时间的测定 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| EN 743-1994 | 塑料管道和导管系统 热塑管 纵向复原的测定 | Plastic piping and ducting systems -Thermoplastics pipes -Determination of the longitudinal reversion |
| EN 744-1995 | 塑料管道和导管系统 热塑管 连续法耐外部吹风的试验方法 | Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method |
| EN 761-1994 | 塑料管道系统 玻璃增强热固性塑料管 干燥条件蠕变系数的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under dry conditions |
| EN 763-1994 | 塑料管道和导管系统 喷射铸模热塑型配件 外观检查加热效果的试验方法 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Test method for visually assessing effects of heating |
| EN 802-1994 | 塑料管道和导管系统 压力管道系统的喷射铸造热塑性部件 挤压最大变形试验方法 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for pressure piping systems - Test method for maximum deformation by crushing |
| EN 803-1994 | 塑料管道系统 压力管道的弹性密封环状连接的喷射铸造热塑性部件 无轴向推力的瞬时内压阻力试验方法 | Plastics piping systems - Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust |
| EN 804-1994 | 塑料管道系统 压力管道溶焊接头的喷射铸造插接部件 瞬时内部液压阻力的试验方法 | Plastics piping systems - Injection-moulded socket fittings for solvent-cemented joints for pressure piping - Test method for resistance to a short-term internal hydrostatic pressure |
| EN 855-1996 | 塑料软管和软管配件 热塑料织物增强液压型 规范 | Plastics hoses and hose assemblies - Thermoplastics textile reinforced hydraulic type - Specification |
| EN 868-5-1999+AC-2001 | 经消毒的医疗器械用包装材料和系统 第5部分：纸、塑料薄膜结构的热和可自密封袋及卷轴 要求和试验方法 | Packaging materials and systems for medical devices which are to be sterilized - Part 5: Heat and self-sealable pouches and reels of paper and plastic film construction - Requirements and test methods |
| EN 911-1995 | 塑料管道系统 热塑塑料压力管道用的弹性密封环型接头和机械接头 外部液压条件下防漏密封试验方法 | Plastics piping systems - Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - Test method for leaktightness under external hydrostatic pressure |
| EN 917-1997 | 塑料管系统 热塑阀门 抗内压和泄漏密封性的试验方法 | Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal pressure and leaktightness |
| EN 921-1994+AC-1995 | 塑料管道系统 热塑管 恒定温度下耐内压的测定 | Plastics piping systems - Thermoplastics pipes - Determination of resistance to internal pressure at constant temperature / Note: To be replaced by prEN ISO 1167-1 (2003-04), prEN ISO 1167-2 (2003-04). |
| EN 922-1994 | 塑料管和管道系统 未增塑聚氯乙烯管道和配件 粘度值测定和K值计算的样品准备 | Plastics piping and ducting systems - Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) - Specimen preparation for determination of the viscosity number and calculation of the K-value |
| EN 976-1-1997 | 玻璃增强塑料地下贮罐 非压力存储液体石油燃料水平园柱状水箱 第1部分：单壁水箱试验方法和要求 | Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Part 1: Requirements and test methods for single wall tanks |
| EN 976-2-1997 | 玻璃增强塑料地下贮罐 非压力存储液体石油燃料水平园柱状贮罐 第2部分：单壁贮罐的运输、储存、操作和安 | Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Part 2: Transport, handling, storage and installation of single wall tanks |
| EN 977-1997 | 玻璃增强塑料地下贮罐 单侧液流法 | Underground tanks of glass-reinforced plastics (GRP) - Method for one side exposure to fluids |
| EN 978-1997 | 玻璃增强塑料地下贮罐 α因子和β因子的测定 | Underground tanks of glass-reinforced plastics (GRP) - Determination of factor and factor |
| EN ISO 10082-1999 | 塑料 酚醛树脂 分类和试验方法 | Plastics - Phenolic resins - Classification and test methods (ISO 10082:1999) |
| EN ISO 10093-1998 | 塑料 燃烧试验 标准火源 | Plastics - Fire tests - Standard ignition sources (ISO 10093:1998) |
| EN ISO 10350-1-2000 | 塑料 可比单点数据的采集和表示 第1部分：模塑材料 | Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:1998) |
| EN ISO 10350-2-2001 | 塑料 可比单点数据的采集和表示 第2部分：长纤维增强塑料 | Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2001) |
| EN ISO 10352-1997 | 纤维增强塑料 模塑料和预浸料 单位面积质量的测定 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass per unit area (ISO 10352:1997) |
| EN ISO 10366-1-2002 | 塑料 甲基丙烯酸甲酯/丙烯腈/丁二烯/苯乙烯(MABS)模塑和挤塑材料 第１部分：命名系统和基本规范 | Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 10366-1:2002) |
| EN ISO 10366-2-1999 | 塑料 甲基丙烯酸甲酯/丙烯腈/丁二烯/苯乙烯(MABS)模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Methyl methacrylate/acrylonitrile/butadiene/styrene (MABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 10366-2:1994) |
| EN ISO 1043-1-2001 | 塑料 符号和缩略语 第1部分：基本聚合物及其特性 | Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001) |
| EN ISO 1043-2-2001 | 塑料 符号和缩略语 第2部分：填充剂及加强材料 | Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials (ISO 1043-2:2000) |
| EN ISO 1043-3-1999 | 塑料 符号和缩略语 第3部分：增塑剂 | Plastics - Symbols and abbreviated terms - Part 3: Plasticizers (ISO 1043-3:1996) |
| EN ISO 1043-4-1999 | 塑料 符号和缩略语 第4部分：阻燃剂 | Plastics - Symbols and abbreviated terms - Part 4: Flame retardants (ISO 1043-4:1998) |
| EN ISO 1060-1-1999 | 塑料 氯乙烯的均聚物和共聚树脂 第1部分：命名体系和基本规范 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications (ISO 1060-1:1998) |
| EN ISO 1060-2-1999 | 塑料 氯乙烯的均聚物和共聚树脂 第2部分：试样的制备和性能的测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 2: Preparation of test samples and determination of properties (ISO 1060-2:1998) |
| EN ISO 1061-1999 | 塑料 未赠塑的乙酸纤维素 游离酸度的测定 | Plastics - Unplasticized cellulose acetate - Determination of free acidity (ISO 1061:1990) |
| EN ISO 10724-1-2001 | 塑料 热固性粉末模塑复合物试样的注射模塑成型 第1部分：一般原则和多用途试样的模塑成型 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens (ISO 10724-1:1998) |
| EN ISO 10724-2-2000 | 塑料 热固性粉末模塑复合物试样的注射模塑成型 第2部分：小板材 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 2: Small plates (ISO 10724-2:1998) |
| EN ISO 10960-1996 | 橡胶和塑料软管 动态条件下耐臭氧性的评定 | Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions (ISO 10960:1994) |
| EN ISO 1110-1997 | 塑料 聚先胺 试样的加速状态调节 | Plastics - Polyamides - Accelerated conditioning of test specimens (ISO 1110:1995) |
| EN ISO 11248-1999 | 塑料 热固性模塑料 温升时短暂性能的评价 | Plastics - Thermosetting moulding materials - Evaluation of short-term performance at elevated temperatures(ISO 11248:1993) |
| EN ISO 1133-1999 | 塑料 热塑性塑料熔体质量流动速率(MFR)和熔体体积流动速率(MFR)的测定 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:1997) |
| EN ISO 11357-1-1997 | 塑料 差示扫描量热法(DSC) 第1部分：一般原则 | Plastics - Differential scanning calorimetry (DSC) - Part 1: General principles (ISO 11357-1:1997) |
| EN ISO 11358-1997 | 塑料 高聚物的热重分析法(TG) 一般原则 | Plastics - Thermogravimetry (TG) of polymers - General principles (ISO 11358:1997) |
| EN ISO 11376-2001 | 塑料 环氧树脂和缩水甘油基酯 无机氯的测定 | Plastics - Epoxy resins and glycidyl esters - Determination of inorganic chlorine (ISO 11376:1997) |
| EN ISO 11401-1998 | 塑料 酚醛树脂 用液相色谱法分离 | Plastics - Phenolic resins - Separation by liquid chromatography (ISO 11401:1993) |
| EN ISO 11402-1998 | 塑料 综合树脂 游离甲醛的测定 | Plastics - Condensation resins - Determination of free formaldehyde (ISO 11402:1993) |
| EN ISO 11403-1-2003 | 塑料 可比多点数据的采集和表示 第1部分：机械性能 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2001) |
| EN ISO 11403-2-1999 | 塑料 可比多点数据的采集和表示 第2部分：热和加工性能 | Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:1995) |
| EN ISO 11403-3-2001 | 塑料 可比多点数据的采集和表示 第3部分：环境对性能的影响 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:1999) |
| EN ISO 11409-1998 | 塑料 酚醛树脂 用差示扫描量热法测定反应热及温度 | Plastics - Phenolic resins - Determination of heats and temperatures of reaction by differential scanning calorimetry (ISO 11409:1993) |
| EN ISO 11468-1999 | 塑料 试验用聚氯乙烯糊料的制备 溶解方法 | Plastics - Preparation of PVC pastes for test purposes - Dissolver method (ISO 11468:1997) |
| EN ISO 11469-2000 | 塑料 塑料产品的一般鉴定和标志 | Plastics - Generic identification and marking of plastics products (ISO 11469:2000) |
| EN ISO 11542-1-2001 | 塑料 超高分子量聚乙烯(PE-UHMW)模塑和挤塑材料 第1部分：命名系统和基本规范 | Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 11542-1:2001) |
| EN ISO 11542-2-1998 | 塑料 超高分子量聚乙烯(PE-UHMW)模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 11542-2:1998) |
| EN ISO 1157-1999 | 塑料 稀溶液中的乙酸纤维 粘度值和粘度率的测定 | Plastics - Cellulose acetate in dilute solution - Determination of viscosity number and viscosity ratio (ISO 1157:1990) |
| EN ISO 1158-1998 | 塑料 氯乙烯均聚物和共聚物 氯含量的测定 | Plastics - Vinyl chloride homopolymers and copolymers - Determination of chlorine content (ISO 1158:1998) |
| EN ISO 1163-1-1999 | 塑料 未增塑聚氯乙烯 (PUC－U)模塑和挤塑材料 第1部分：命名系统和基本规范 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1163-1:1995) |
| EN ISO 1163-2-1999 | 塑料 未增塑聚氯乙烯均聚物和共聚物的化合物 第2部分：试样的制备和性能的测定 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1163-2:1995) |
| EN ISO 11667-1999 | 纤维增强塑料 模塑料和预浸料 树脂、增强纤维和矿物质填料含量的测定 溶解法 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of resin, reinforced-fibre and mineral-filler content - Dissolution methods (ISO 11667:1997) |
| EN ISO 1172-1998 | 纺织玻璃纤维增强塑料、预浸料、模塑料和层压塑料纺织玻璃纤维和矿物质填料含量的测定 煅烧法 | Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content - Calcination methods (ISO 1172:1996) |
| EN ISO 11758-1997+AC-1998 | 橡胶和塑料软管 氙弧灯照射 颜色和外观变化的测定 | Rubber and plastics hoses - Exposure to a xenon arc lamp - Determination of changes in colour and appearance (ISO 11758:1995) |
| EN ISO 1183-3-1999 | 塑料 非泡沫塑料的密度测定方法 第3部分：气体比重瓶法 | Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method (ISO 1183-3:1999) |
| EN ISO 119-1998 | 塑料 酚－醛模塑件 游离酚的测定 碘量法 | Plastics - Phenol-formaldehyde mouldings - Determination of free phenols - Iodometric method (ISO 119:1977) |
| EN ISO 11963-1995 | 塑料 聚碳酸酯板材 类型、尺寸和特性 | Plastics - Polycarbonate sheets - Types, dimensions and characteristics (ISO 11963:1995) |
| EN ISO 120-1998 | 塑料 酚－醛模塑件 游离氨和铵化合物的测定 比色法 | Plastics - Phenol-formaldehyde mouldings - Determination of free ammonia and ammonium compounds - Colorimetric comparison method (ISO 120:1977) |
| EN ISO 12017-1996 | 塑料 聚甲基丙烯酸甲酯双合板和三合板 试验方法 | Plastics - Poly(methyl methacrylate) double- and triple-skin sheets - Test methods (ISO 12017:1995) |
| EN ISO 12058-1-2002 | 塑料 用落球粘度计测定粘度 第1部分：倾斜管法 | Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997) |
| EN ISO 12086-1-1999 | 塑料 含氟聚合物分散体模塑和挤塑材料 第1部分：命名系统和基本规范 | Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 12086-1:1995) |
| EN ISO 12086-2-1999 | 塑料 含氟聚合物分散体模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 12086-2:1995) |
| EN ISO 12114-1997 | 纤维增强塑料 热固性模压塑料和预浸料 固化特性的测定 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of cure characteristics (ISO 12114:1997) |
| EN ISO 12115-1997 | 纤维增强塑料 热固性模压塑料和预浸料 流动性、熟化期和适用期的测定 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of flowability, maturation and shelf life (ISO 12115:1997) |
| EN ISO 12162-1995 | 压力用热塑性塑料管材和管件分级和命名 总体使用(设计)系数 | Thermoplastics materials for pipes and fittings for pressure applications - Classification and designation - Overall service (design) coefficient (ISO 12162:1995) |
| EN ISO 1264-1997 | 塑料 氯乙烯均聚物和共聚物树脂 水萃取物的pH值测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of pH of aqueous extract (ISO 1264:1980) |
| EN ISO 1265-1997 | 塑料 聚氯乙烯树脂 杂质和外来杂质数的测定 | Plastics - Polyvinyl chloride resins - Determination of number of impurities and foreign particles (ISO 1265:1979) |
| EN ISO 13000-1-1997 | 塑料 聚四氟乙烯(PTFE)半成品 第1部分：要求和命名 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:1997) |
| EN ISO 13000-2-1997 | 塑料 聚四氟乙烯(PTFE)半成品 第2部分：试样的制备和性能的测定 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:1997) |
| EN ISO 1307-1995 | 一般工业用橡胶和塑料软管 孔径和公差及长度公差 | Rubber and plastics hoses for general-purpose industrial applications - Bore diameters and tolerances, and tolerances on length (ISO 1307:1992) |
| EN ISO 13468-1-1996 | 塑料 透明材料光透射率总量的测定 第1部分：单束光发射仪器 | Plastics - Determination of the total luminous transmittance of transparent materials - Part 1: Single-beam instrument (ISO 13468-1:1996) |
| EN ISO 13478-1997 | 流体输送用热塑性塑料管材 耐快速裂纹扩展(RCP)的测定 全尺寸试验(FST) | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:1997) |
| EN ISO 13760-1998 | 流体输送用塑料压力管材 Miner规则 累积破坏的计算方法 | Plastics pipes for the conveyance of fluids under pressure - Miners rule - Calculation method for cumulative damage (ISO 13760:1998) |
| EN ISO 13783-1997 | 塑料管道系统 硬聚氯乙烯(PVC-U)端部承受负荷的双承口连接件 密封和承受弯曲及内压的试验方法 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double socket joints - Test method for leaktightness and strength while subjected to bending and internal pressure (ISO 13783:1997) |
| EN ISO 13844-2000 | 塑料管道系统 用于硬(聚氯乙烯)(PVC-U) 管道的弹性密封环式承口连接件 负压下密封试验方法 | Plastics piping systems - Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure (ISO 13844:2000) |
| EN ISO 13845-2000 | 塑料管道系统 用于硬(聚氯乙烯)(PVC-U) 管道的弹性密封环式承口连接件 内压下角度偏转密封试验方法 | Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with angular deflection (ISO 13845:2000) |
| EN ISO 13846-2000 | 塑料管道系统 热塑性加压塑料管道用端部负载轴承和非端部负载轴承的安装和连接 在内水压下长期密封的试验 | Plastics piping systems - End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaktightness under internal water pressure (ISO 13846:2000) |
| EN ISO 13927-2003 | 塑料 用锥形辐射加热器和热电堆探测器进行简单热释放试验 | Plastics - Simple heat release test using a conical radiant heater and a thermopile detector (ISO 13927:2001) |
| EN ISO 1402-1996 | 橡胶和塑料软管和软管组件 液压试验 | Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:1994) |
| EN ISO 14113-1997 | 气焊设备 最大设计压力为450bar的压塑空气和液化气用橡胶和塑料软管组件 | Gas welding equipment - Rubber and plastic hoses assembled for compressed or liquefied gases up to a maximum design pressure of 450 bar (ISO 14113:1997) |
| EN ISO 14125-1998 | 纤维增强塑料复合材料 弯曲性能的测定 | Fibre-reinforced plastic composites - Determination of flexural properties (ISO 14125:1998) |
| EN ISO 14126-1999 | 纤维增强塑料复合材料 平面方向压缩性的测定 | Fibre-reinforced plastic composites - Determination of compressive properties in the in-plane direction (ISO 14126:1999) |
| EN ISO 14129-1997 | 纤维增强塑料复合材料 用±45°张力试验法测定平面剪应力/剪应变特性、包括平面切变模量和剪切强度 | Fibre-reinforced plastic composites - Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength, by ?45°tension test method (ISO 14129:1997) |
| EN ISO 14130-1997 | 纤维增强塑料复合材料 用短试片法测定表观层间粘合剪切强度 | Fibre-reinforced plastic composites - Determination of apparent interlaminar shear strength by short-beam method (ISO 14130:1997) |
| EN ISO 1421-1998 | 橡胶或塑料涂覆织物 拉伸强度和断裂伸长的测定 | Rubber- or plastics-coated fabrics - Determination of tensile strength and elongation at break (ISO 1421:1998) |
| EN ISO 14526-1-1999 | 塑料 酚醛粉末模塑化合物(PF-PMCs) 第1部分：命名体系及基本规范 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 1: Designation system and basis for specifications (ISO 14526-1:1999) |
| EN ISO 14526-2-1999 | 塑料 酚醛粉末模塑化合物(PF-PMCs) 第2部分：试样的制备和性能的测定 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14526-2:1999) |
| EN ISO 14526-3-1999 | 塑料 酚醛粉末模塑化合物(PF-PMCs) 第3部分：对所选模塑化合物的要求 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14526-3:1999) |
| EN ISO 14527-1-1999 | 塑料 脲醛和脲/蜜胺酚醛粉末模塑化合物(UF- 和UF/MF-PMCs) 第1部分：命名体系及基本规范 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 1: Designation system and basis for specifications (ISO 14527-1:1999) |
| EN ISO 14527-2-1999 | 塑料 脲醛和脲/蜜胺酚醛粉末模塑化合物(UF- 和UF/MF-PMCs) 第2部分：试样的制备和性能的测定 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14527-2:1999) |
| EN ISO 14527-3-1999 | 塑料 脲醛和脲/蜜胺酚醛粉末模塑化合物(UF- 和UF/MF-PMCs) 第3部分：对选择的模塑化合物的要求 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14527-3:1999) |
| EN ISO 14528-1-1999 | 塑料 蜜胺酚醛粉末模塑化合物(MF-PMCs) 第1部分：命名体系及基本规范 | m und Basi Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Part 1: Designation system and basis for specifications (ISO 14528-1:1999) |
| EN ISO 14528-2-1999 | 塑料 蜜胺酚醛粉末模塑化合物(MF-PMCs) 第2部分：试样的制备和性能的测定 | Plastics - Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14528-2:1999) |
| EN ISO 14528-3-1999 | 塑料 蜜胺酚醛粉末模塑化合物(MF-PMCs) 第3部分：对所选模塑化合物的要求 | Plastics - Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14528-3:1999) |
| EN ISO 14529-1-1999 | 塑料 蜜胺/酚醛粉末模塑化合物(MP-PMCs) 第1部分：命名体系及基本规范 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 1: Designation system and basis for specifications (ISO 14529-1:1999) |
| EN ISO 14529-2-1999 | 塑料 蜜胺/酚醛粉末模塑化合物(MP-PMCs) 第2部分：试样的制备和性能的测定 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14529-2:1999) |
| EN ISO 14529-3-1999 | 塑料 蜜胺/酚醛粉末模塑化合物(MP-PMCs) 第3部分：对所选模塑化合物的要求 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14529-3:1999) |
| EN ISO 14530-1-1999 | 塑料 不饱和聚酯粉末模塑化合物(UP-PMCs) 第1部分：命名体系及基本规范 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 1: Designation system and basis for specifications (ISO 14530-1:1999) |
| EN ISO 14530-2-1999 | 塑料 不饱和聚酯粉末模塑化合物(UP-PMCs) 第2部分：试样的制备和性能的测定 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14530-2:1999) |
| EN ISO 14530-3-1999 | 塑料 不饱和聚酯粉末模塑化合物(UP-PMCs) 第3部分：对所选择模塑化合物的要求 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14530-3:1999) |
| EN ISO 14692-1-2002 | 石油和天然气工业 玻璃纤维增强塑料管 第1部分：词汇、符号、设备和材料 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2002) |
| EN ISO 14692-2-2002 | 石油和天然气工业 玻璃纤维增强塑料管 第2部分：资格和制造 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002) |
| EN ISO 14692-3-2002 | 石油和天然气工业 玻璃纤维增强塑料管 第3部分：系统设计 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2002) |
| EN ISO 14692-4-2002 | 石油和天然气工业 玻璃纤维增强塑料管 第4部分：制造 、安装和运行 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2002) |
| EN ISO 14890-2003 | 传输带 一般用敷橡胶或塑料的织物传输带规范 | Conveyor belts - Specification for rubber or plastics covered conveyor belts of textile construction for general use (ISO 14890:2003) |
| EN ISO 14896-2001 | 塑料 聚氨酯原材料 异氰酸酯的测定 | Plastics - Polyurethane raw materials - Determination of isocyanate content (ISO 14896:2000) |
| EN ISO 15252-1-1999 | 塑料 环氧树脂模塑化合物(EP-PMCs) 第1部分：命名体系及基本规范 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 1: Designation system and basis for specifications (ISO 15252-1:1999) |
| EN ISO 15252-2-1999 | 塑料 环氧树脂模塑化合物(EP-PMCs) 第2部分：试样的准备和特性的测定 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 15252-2:1999) |
| EN ISO 15252-3-1999 | 塑料 环氧树脂模塑化合物(EP-PMCs) 第3部分：对所选模塑化合物的要求 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 15252-3:1999) |
| EN ISO 15493-2003 | 工业用塑料管道系统 丙烯腈丁二烯苯乙烯（ABS），未增塑聚氯乙烯（PVC-U）和氯化聚氯乙烯（PVC-C）米制部件 | Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specificatio |
| EN ISO 15494-2003 | 工业用塑料管道系统 聚丁烯（PB），聚乙烯（PE）和聚丙烯（PP） 米制部件和系统规范 | Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the system; Metric series (ISO 15494:2003) |
| EN ISO 15908-2002 | 热塑塑料管道用胶粘剂 胶粘剂热稳定性的测试方法 | Adhesives for thermoplastic piping systems - Test method for the determination of thermal stability of adhesives (ISO 15908:2002) |
| EN ISO 1597-1999 | 塑料 未増塑的乙酸纤维 乙酸量的测定 | Plastics - Unplasticized cellulose acetate - Determination of acetic acid yield (ISO 1597:1994) |
| EN ISO 1598-1999 | 塑料 乙酸纤维素 不溶物的测定 | Plastics - Cellulose acetate - Determination of insoluble particles (ISO 1598:1990) |
| EN ISO 1599-1999 | 塑料 乙酸纤维素 模塑时粘度降低的测定 | Plastics - Cellulose acetate - Determination of viscosity loss on moulding (ISO 1599:1990) |
| EN ISO 1600-1999 | 塑料 乙酸纤维素 利用热的不同循环在生产模制样品中吸收量的测定 | Plastics - Cellulose acetate - Determination of light absorption on moulded specimens produced using different periods of heating (ISO 1600:1990) |
| EN ISO 1622-1-1999 | 塑料 聚苯乙烯(PS)模塑和挤塑材料 第1部分：命名体系和基本规范 | Plastics - Polystyrene (PS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1622-1:1994) |
| EN ISO 1622-2-1999 | 塑料 聚苯乙烯(PS)模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Polystyrene (PS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1622-2:1995) |
| EN ISO 1624-2001 | 塑料 聚乙烯均聚物和共聚物树脂 水中筛析 | Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis in water (ISO 1624:2001) |
| EN ISO 1628-1-1998 | 塑料 用毛细管粘度计测定稀溶液中聚合物的粘度 第1部分：一般原则 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 1: General principles (ISO 1628-1:1998) |
| EN ISO 1628-2-1998 | 塑料 用毛细管粘度计测定稀溶液中聚合物的粘度 第2部分：聚氯乙烯树脂 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 2: Poly(vinyl chloride) resins (ISO 1628-2:1998) |
| EN ISO 1628-3-2003 | 塑料 用毛细管粘度计测定聚合物在稀释溶液中的粘数 第３部分：聚乙烯和聚丙烯 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 3: Polyethylenes and polypropylenes (ISO 1628-3:2001) |
| EN ISO 1675-1998 | 塑料 液态树脂 比重瓶法测定密度 | Plastics - Liquid resins - Determination of density by the pyknometer method (ISO 1675:1985) |
| EN ISO 16871-2003 | 塑料管道和导管系统 塑料管道和配件 直接(自然)风化的方法 | Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering (ISO 16871:2003) |
| EN ISO 172-1998 | 塑料 酚－醛模塑件 游离氨的检验 | Plastics - Phenol-formaldehyde mouldings - Detection of free ammonia (ISO 172:1978) |
| EN ISO 1746-2000 | 橡胶或塑料软管和管件 弯曲试验 | Rubber or plastics hoses and tubing - Bending tests (ISO 1746:1998, including technical corrigendum 1:1999) |
| EN ISO 175-2000 | 塑料 测定液体化学品对塑料影响的试验方法 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:1999) |
| EN ISO 176-1999 | 塑料 增塑剂损耗的测定 活性碳法 | Plastics - Determination of loss of plasticizers - Activated carbon method (ISO 176:1976) |
| EN ISO 177-1999 | 塑料 增塑剂分散性的测定 | Plastics - Determination of migration of plasticizers (ISO 177:1988) |
| EN ISO 178-2003 | 塑料 弯曲性能测定 | Plastics - Determination of flexural properties (ISO 178:2001) |
| EN ISO 179-1-2000 | 塑料 摆锤式冲击特性的测定 第1部分：非仪器冲击试验 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2000) |
| EN ISO 179-2-1999 | 塑料 锤式冲击特性的测定 第2部分：仪器冲击试验 | Plastics - Determination of Charpy impact properties - Part 2: Instrumented impact test (ISO 179-2:1997) |
| EN ISO 1797-2-1995 | 牙科旋转器械 柄 第2部分：塑料柄 | Dental rotary equipment - Shanks - Part 2: Shanks made of plastics (ISO 1797-2:1992) |
| EN ISO 180-2000 | 塑料 伊兆特冲击强度的测定 | Plastics - Determination of Izod impact strength (ISO 180:2000) |
| EN ISO 182-2-1999 | 塑料 基于氯乙烯共聚物、均聚物的化合物及产物在高温下析出氯化氢和其它酸性产物的趋势测定 第2部分：pH | Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 2: pH method (ISO 182-2:1990) |
| EN ISO 182-3-2000 | 塑料 基于氯乙烯共聚物、均聚物的化合物及产物在高温下析出氯化氢和其它酸性产物的趋势测定 第3部分：电 | Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 3: Conductometric method (ISO 182-3:1993) |
| EN ISO 182-4-2000 | 塑料 基于氯乙烯共聚物、均聚物的化合物及产物在高温下析出氯化氢和其它酸性产物的趋势测定 第 4部分：电 | Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 4: Potentiometric method (ISO 182-4:1993) |
| EN ISO 183-1999 | 塑料 着色剂渗析的定性评估 | Plastics - Qualitative evaluation of the bleeding of colorants (ISO 183:1976) |
| EN ISO 1872-1-1999+A1-2000 | 塑料 聚乙烯(PE)模塑和挤塑材料 第1部分：命名体系和基本规范 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1872-1:1993) |
| EN ISO 1872-2-1997 | 塑料 聚乙烯(PE)模塑和挤塑材料 第2部分：试样制备和性能测定 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1872-2:1997) |
| EN ISO 1873-1-1995 | 塑料 聚丙烯(PP)模塑和挤塑材料 第1部分：标识系统和基本规范 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1873-1:1995) |
| EN ISO 1873-2-1997+A1-2000 | 塑料 聚丙烯(PP)模塑和挤塑材料 第2部分：试样制备和性能测定 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1873-2:1997) |
| EN ISO 1874-1-2000 | 塑料 聚酰胺(PA)模塑和挤塑材料 第1部分：命名 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation (ISO 1874-1:1992) |
| EN ISO 1874-2-1995 | 塑料 聚酰胺(PA)模塑和挤塑材料 第2部分：试样制备和性能测定 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:1995) |
| EN ISO 1923-1995 | 泡沫塑料和橡胶 线性尺寸的测定 | Cellular plastics and rubbers - Determination of linear dimensions (ISO 1923:1981) |
| EN ISO 2039-1-2003 | 塑料 硬度测定 第1部分：压球法 | Plastics - Determination of hardness - Part 1: Ball indentation method (ISO 2039-1:2001) |
| EN ISO 2039-2-1999 | 塑料 硬度测定 第2部分：洛氏硬度 | Plastics - Determination of hardness - Part 2: Rockwell hardness (ISO 2039-2:1987) |
| EN ISO 2114-2000 | 塑料（聚酯树脂）、色漆和清漆（胶粘合剂） 部分酸值和总酸值的测定 | Plastics (polyester resins) and paints and varnishes (binders) - Determination of partial acid value and total acid value (ISO 2114:2000) |
| EN ISO 2231-1995 | 橡胶或塑料涂覆织物 状态调节和试验的标准环境 | Rubber- or plastics-coated fabrics - Standard atmospheres for conditioning and testing (ISO 2231:1989) |
| EN ISO 2286-1-1998 | 橡胶或塑料涂覆织物 整卷特性测定 第1部分：长度、宽度和净重的测定方法 | Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 1: Methods for determination of length, width and net mass (ISO 2286-1:1998) |
| EN ISO 2286-2-1998 | 橡胶或塑料涂覆织物 整卷特性测定 第2部分：单位面积总质量、单位面积涂胶量和衬底单位面积质量的测定方 | Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 2: Methods for determination of total mass per unit area, mass per unit area of coating and mass per unit area of substrate (ISO 2286-2:1998) |
| EN ISO 2286-3-1998 | 橡胶或塑料涂覆织物 整卷特性测定 第3部分：厚度测定方法 | Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 3: Method for determination of thickness (ISO 2286-3:1998) |
| EN ISO 2411-2000 | 橡胶或塑料涂覆织物 涂层粘合强度的测定 | Rubber- or plastics-coated fabrics - Determination of coating adhesion (ISO 2411:2000) |
| EN ISO 2535-2002 | 塑料 不饱和聚脂树脂 25℃时胶凝时间的测量 | Plastics - Unsaturated polyester resins - Measurement of gel time at ambient temperature (ISO 2535:2001) |
| EN ISO 2554-1998 | 塑料 不饱和聚脂树脂 羟基值的测定 | Plastics - Unsaturated polyester resins - Determination of hydroxyl value (ISO 2554:1997) |
| EN ISO 2555-1999 | 塑料 液态或乳态或分散状树脂 用落球式粘度计测定表观粘度 | Plastics - Resins in the liquid state or as emulsions or dispersions - Determination of apparent viscosity by the Brookfield test method (ISO 2555:1989) |
| EN ISO 2556-2000 | 塑料 在大气压力下薄膜和薄板的透气率的测定 测压法 | Plastics - Determination of the gas transmission rate of films and thin sheets under atmospheric pressure - Manometric method (ISO 2556:1974) |
| EN ISO 2578-1998 | 塑料 长期热暴露作用后时间和温度极限的测定 | Plastics - Determination of time-temperature limits after prolonged exposure to heat (ISO 2578:1993) |
| EN ISO 2580-1-2002 | 塑料 丙烯晴-丁二烯-苯乙烯共聚物(ABS)的模塑和挤塑材料 第1部分：命名系统和基本规范 | Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2002) |
| EN ISO 2580-2-1999 | 塑料 丙烯晴-丁二烯-苯乙烯共聚物(ABS)的模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Acrylonitrile/butadiene/styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2580-2:1994) |
| EN ISO 2818-1996 | 塑料 试样的机加工制备 | Plastics - Preparation of test specimens by machining (ISO 2818:1994) |
| EN ISO 2897-1-1999 | 塑料 耐冲击聚苯乙烯(PS-I)模塑和挤塑材料 第1部分：命名系统和基本规范 | Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2897-1:1997) |
| EN ISO 2897-2-1999 | 塑料 耐冲击聚苯乙烯(PS-I)模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2897-2:1994, including Technical Corrigendum 1:1995) |
| EN ISO 2898-1-1999 | 塑料 增塑聚氯乙烯(PVC-P)模塑和挤塑材料 第1部分：命名系统和基本规范 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2898-1:1996) |
| EN ISO 2898-2-1999 | 塑料 增塑聚氯乙烯(PVC-P)模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2898-2:1997) |
| EN ISO 291-1997 | 塑料 状态调节和试验用标准大气压 | Plastics - Standard atmospheres for conditioning and testing (ISO 291:1997) |
| EN ISO 293-2003 | 塑料 热塑性材料的压模塑试样 | Plastics - Compression moulding test specimens of thermoplastic materials (ISO 293:1986) |
| EN ISO 294-1-1998+A1-2002 | 塑料 热塑性材料试样的注模塑法 第1部分：一般原则、多用途模塑件及条形试样 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:1996) |
| EN ISO 294-2-1998 | 塑料 热塑性材料试样的注模塑法 第2部分：小拉伸棒 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars (ISO 294-2:1996) |
| EN ISO 294-3-2003 | 塑料 热塑性材料试样的注模塑法 第3部分：小板 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2002) |
| EN ISO 294-4-2003 | 塑料 热塑性材料试样的注模塑法 第4部分：模塑收缩率的测定 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4: Determination of moulding shrinkage (ISO 294-4:2001) |
| EN ISO 295-1998 | 塑料 热固性材料试样的压模塑法 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:1991) |
| EN ISO 3001-1999 | 塑料 环氧化合物 环氧基当量的测定 | Plastics - Epoxy compounds - Determination of epoxy equivalent (ISO 3001:1999) |
| EN ISO 305-1999 | 塑料 聚氯乙烯和有关均聚合物和共聚物及其混合物的热稳定性的测定 色变法 | Plastics - Determination of thermal stability of poly(vinyl chloride), related chlorine - Containing homopolymers and copolymers and their compounds - Discoloration method (ISO 305:1990) |
| EN ISO 306-1996 | 塑料 热塑性材料 维卡软化温度的测定 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:1994) |
| EN ISO 307-2003 | 塑料 聚酰胺 粘度值的测定 | Plastics - Polyamides - Determination of viscosity number (ISO 307:2003) |
| EN ISO 308-1997 | 塑料 酚醛模塑材料 丙酮可溶性物质(在未模塑状态时表现树脂含量)的测定 | Plastics - Phenolic moulding materials - Determination of acetone-soluble matter (apparent resin content of material in the unmoulded state) (ISO 308:1994) |
| EN ISO 3146-2000+AC-2002 | 塑料 用毛细管和偏振显微镜测定半晶壮聚合物的熔化性能(熔化温度和熔化区域) | Plastics - Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods (ISO 3146:2000) |
| EN ISO 3167-2003 | 塑料 多用途试验用试样 | Plastics - Multipurpose test specimens (ISO 3167:2002) |
| EN ISO 3219-1994 | 塑料 液态或乳态或分散状的聚合物/树脂 使用规定剪切率的旋转式粘度计测定粘度 | Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate (ISO 3219:1993) |
| EN ISO 3451-1-1997 | 塑料 灰分的测定 第1部分：一般方法 | Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:1997) |
| EN ISO 3451-4-2000 | 塑料 灰分的测定 第4部分：聚酰胺 | Plastics - Determination of ash - Part 4: Polyamides (ISO 3451-4:1998) |
| EN ISO 3451-5-2002 | 塑料 灰份的测定 第5部分：聚氯乙烯 | Plastics - Determination of ash - Part 5: Poly(vinyl chloride) (ISO 3451-5:2002) |
| EN ISO 3521-1999 | 塑料 不饱和聚酯和环氧树脂 总体积收缩率的测定 | Plastics - Unsaturated polyester and epoxy resins - Determination of overall volume shrinkage (ISO 3521:1997) |
| EN ISO 3671-1998 | 塑料 氨基模塑材料 挥发性物质的测定 | Plastics - Aminoplastic moulding materials - Determination of volatile matter (ISO 3671:1976) |
| EN ISO 3672-1-2001 | 塑料 不饱和聚酯树脂 第1部分：命名体系 | Plastics - Unsaturated-polyester resins (UP-R) - Part 1: Designation system (ISO 3672-1:2000) |
| EN ISO 3672-2-2001 | 塑料 不饱和聚酯树脂 第2部分：试样的制备和特性的测定 | Plastics - Unsaturated-polyester resins (UP-R) - Part 2: Preparation of test specimens and determination of properties (ISO 3672-2:2000) |
| EN ISO 3673-1-1999 | 塑料 环氧树脂 第1部分：命名 | Plastics - Epoxy resins - Part 1 : Designation (ISO 3673-1:1996) |
| EN ISO 3673-2-1999 | 塑料 环氧树脂 第2部分：试样的制备和特性的测定 | Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties (ISO 3673-2:1999) |
| EN ISO 3915-1999 | 塑料 导电塑料电阻率的测定 | Plastics - Measurement of resistivity of conductive plastics (ISO 3915:1981) |
| EN ISO 3994-2000 | 塑料软管 给排水用螺纹型热塑性软管 规范 | Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification (ISO 3994:1998) |
| EN ISO 4080-1995+AC-1998 | 橡胶与塑料软管和软管组件 漏气氯的测定 | Rubber and plastics hoses and hose assemblies - Determination of permeability to gas (ISO 4080:1991) |
| EN ISO 4577-1999 | 塑料 聚丙烯和聚丙烯共聚物 空气中氧化稳定性的测定 烘箱法 | Plastics - Polypropylene and propylene-copolymers - Determination of thermal oxidative stability in air - Oven method (ISO 4577:1983) |
| EN ISO 4583-1998 | 塑料 环氧树脂和有关材料 易皂化氯的测定 | Plastics - Epoxy resins and related materials - Determination of easily saponifiable chlorine (ISO 4583:1998) |
| EN ISO 4589-1-1999 | 塑料 通过氧指数测定其燃烧性 第1部分：指南 | Plastics - Determination of burning behaviour by oxygen index - Part 1: Guidance (ISO 4589-1:1996) |
| EN ISO 4589-2-1999 | 塑料 通过氧指数测定其燃烧性 第2部分：室温试验 | Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test (ISO 4589-2:1996) |
| EN ISO 4589-3-1996 | 塑料 通过氧指数测定其燃烧性 第3部分：高温试验 | Plastics - Determination of burning behaviour by oxygen index - Part 3: Elevated-temperature test (ISO 4589-3:1996) |
| EN ISO 4590-2003 | 硬质泡沫塑料 材料开孔及闭孔体积百分数的测定 | Rigid cellular plastics - Determination of the volume percentage of open cells and of closed cells (ISO 4590:2002) |
| EN ISO 4597-1-1997 | 塑料 环氧树脂用固化剂和促进剂 第1部分：命名 | Plastics - Hardeners and accelerators for epoxide resins - Part 1: Designation (ISO 4597-1:1983) |
| EN ISO 4599-1996 | 塑料 耐环境应力龟裂的测定 变形片法 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Bent strip method (ISO 4599:1986) |
| EN ISO 4600-1997 | 塑料 耐环境应力龟裂的测定 球或针压痕法 | Plastics - Determination of environmental stress cracking (ESC) - Ball or pin impression method (ISO 4600:1992) |
| EN ISO 4608-1998 | 塑料 氯乙烯 一般用途氯乙烯均聚物和共聚物树脂 室温下增塑剂吸收的测定 | Plastics - Vinylchlorid(VC)-homopolymere and copolymer resins of vinyl chloride for general use - Determination of plasticizer absorption at room temperature (ISO 4608:1998) |
| EN ISO 4610-2001 | 塑料 氯乙烯均聚物和共聚物树脂 用空气喷射筛滤器进行筛析 | Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis using air-jet sieve apparatus (ISO 4610:2001) |
| EN ISO 4611-1999 | 塑料 湿热 水溅和盐雾效应的测定 | Plastics - Determination of the effects of exposure to damp heat, water spray and salt mist (ISO 4611:1987) |
| EN ISO 4612-1999 | 塑料 试验用聚氯乙烯糊料的制备 齿轮传动混合方法 | Plastics - Preparation of PVC pastes for test purposes - Planetary-mixer method (ISO 4612:1999) |
| EN ISO 4613-1-1999 | 塑料 乙酸乙烯／乙烯酯模塑和挤塑材料 第1部分：命名和规范 | Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Part 1: Designation and specification (ISO 4613-1:1993) |
| EN ISO 4613-2-1995 | 塑料 乙酸乙烯／乙烯酯模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 4613-2:1995) |
| EN ISO 4613-2/prA1-2001 | 塑料 乙酸乙烯／乙烯酯模塑和挤塑材料 第2部分：试样的制备和性能的测定 修改1 | Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties; Amendment A1 (ISO 4613-2:1995/DAM 1:2001) |
| EN ISO 4614-1999 | 塑料 三聚氰胺－甲醛模塑件 可萃取的甲醛的测定 | Plastics - Melamine-formaldehyde mouldings - Determination of extractable formaldehyde (ISO 4614:1977) |
| EN ISO 4615-1999 | 塑料 不饱和聚酯和环氧树脂 总氯量的测定 | Plastics - Unsaturated polyesters and epoxide resins - Determination of total chlorine content (ISO 4615:1979) |
| EN ISO 4651-1995 | 泡沫橡胶和塑料 动态缓冲性能测定 | Cellular rubbers and plastics - Determination of dynamic cushioning performance (ISO 4651:1988) |
| EN ISO 4671-2000 | 橡胶和塑料软管和软管组件 尺寸测量方法 | Rubber and plastics hoses and hose assemblies - Methods of measurement of dimensions (ISO 4671:1999) |
| EN ISO 4672-1999 | 橡胶和塑料软管 低温的弯曲试验 | Rubber and plastics hoses - Sub-ambient temperature flexibility tests (ISO 4672:1997) |
| EN ISO 4674-1-2003 | 涂橡胶-或塑料的织物 抗撕裂力的测定 第1部分： 撕裂方法的 恒定速度 | Rubber- or plastics-coated fabrics - Determination of tear resistance - Part 1: Constant rate of tear methods (ISO 4674-1:2003) |
| EN ISO 4674-2-1998 | 橡胶或塑料涂覆织物 抗撕裂性测定 第2部分：冲击摆法 | Rubber- or plastics-coated fabrics - Determination of tear resistance - Part 2: Ballistic pendulum method (ISO 4674-2:1998) |
| EN ISO 472-2001 | 塑料 词汇 | Plastics - Vocabulary (ISO 472:1999) |
| EN ISO 483-1999 | 塑料 水溶液在小密封器中恒定相对湿度值法 | Plastics - Small enclosures for conditioning and testing using aqueous solutions to maintain relative humidity at constant value (ISO 483:1988) |
| EN ISO 489-1999 | 塑料 反射指数的测定 | Plastics - Determination of refractive index (ISO 489:1999) |
| EN ISO 4892-1-2000 | 塑料 实验室光源暴露方法 第1部分：通用指南 | Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:1999) |
| EN ISO 4892-2-1999 | 塑料 实验室光源暴露方法 第2部分：氙弧灯 | Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc sources (ISO 4892-2:1994) |
| EN ISO 4892-3-1999 | 塑料 实验室光源暴露方法 第3部分：UV荧光灯 | Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:1994) |
| EN ISO 4894-1-1999 | 塑料 苯乙烯／丙烯腈(SAN)模塑和挤塑材料 第1部分：命名体系和基本规范 | Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 4894-1:1997) |
| EN ISO 4894-2-1999 | 塑料 苯乙烯／丙烯腈(SAN)模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 4894-2:1995) |
| EN ISO 4895-1999 | 塑料 液态环氧树脂 结晶性的测定 | Plastics - Liquid epoxy resins - Determination of tendency to crystallize (ISO 4895:1997) |
| EN ISO 527-1-1996 | 塑料 拉伸性能的测定 第1部分：一般原则 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:1993 including Corr 1:1994) |
| EN ISO 527-2-1996 | 塑料 拉伸性能的测定 第2部分：模压和挤压塑料试验条件 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:1993 including Corr 1:1994) |
| EN ISO 527-3-1995+AC-1998 | 塑料 拉伸性能的测定 第3部分：簿膜和簿板材的试验条件 | Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets (ISO 527-3:1995) |
| EN ISO 527-4-1997 | 塑料 拉伸性能的测定 第4部分：各向同性及各向异性纤维增强塑料复合材料试验条件 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:1997) |
| EN ISO 527-5-1997 | 塑料 拉伸性能的测定 第5部分：单向纤维增强塑料复合材料试验条件 | Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:1997) |
| EN ISO 5470-1-1999 | 橡胶或塑料涂覆织物 耐磨性的测定 第1部分：片磨器 | Rubber- or plastics-coated fabrics - Determination of abrasion resistance - Part 1: Taber abrader (ISO 5470-1:1999) |
| EN ISO 5470-2-2003 | 涂橡胶或塑料的织物 耐磨性的测定 第2部分：马丁式研磨器 | Rubber- or plastics-coated fabrics - Determination of abrasion resistance - Part 2: Martindale abrader (ISO 5470-2:2003) |
| EN ISO 5659-1-1999 | 塑料 烟雾产生 第1部分：光密度测定指南 | Plastics - Smoke generation - Part 1: Guidance on optical-density testing (ISO 5659-1:1996) |
| EN ISO 5659-2-1998 | 塑料 烟雾产生 第2部分：用单燃烧室检验测定光密度 | Plastics - Smoke generation - Part 2: Determination of optical density by a single-chamber test (ISO 5659-2:1994, including Technical Corrigendum 1:1997) |
| EN ISO 5774-2000 | 压缩空气用织物增强的塑料软管 规范 | Plastics hoses, textile-reinforced, for compressed air - Specification (ISO 5774:1997) |
| EN ISO 584-1997 | 塑料 不饱和聚酯数脂80℃时的反应性测定(常规方法) | Plastics - Unsaturated polyester resins - Determination of reactivity at 80 ℃ (conventional method) (ISO 584:1982) |
| EN ISO 585-1999 | 塑料 未增塑的乙酸纤维素 水分含量的测定 | Plastics - Unplasticized cellulose acetate - Determination of moisture content (ISO 585:1990) |
| EN ISO 5981-1997 | 橡胶或塑料涂覆织物 弯曲剪切和磨损性能测定 | Rubber- or plastics-coated fabrics - Determination of resistance to combined shear flexing and rubbing (ISO 5981:1997) |
| EN ISO 60-1999 | 塑料 专用漏斗注入的材料,表观密度的测定 | Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:1977) |
| EN ISO 604-2003 | 塑料 压缩性能的测定 | Plastics - Determination of compressive properties (ISO 604:2002) |
| EN ISO 61-1999 | 塑料 不能用漏斗注入的模压材料表观密度的测定 | Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:1976) |
| EN ISO 6186-1998 | 塑料 浇注性的测定 | Plastics - Determination of pourability (ISO 6186:1998) |
| EN ISO 62-1999 | 塑料 吸水性的测定 | Plastics - Determination of water absorption (ISO 62:1999) |
| EN ISO 6224-1997 | 一般用途输水用织物增强塑料软管 规范 | Plastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:1995) |
| EN ISO 6252-1997 | 塑料 环境应力龟裂(ESC)的测定 恒定－拉伸－应变法 | Plastics - Determination of environmental stress cracking (ESC) - Constant-tensile-stress method (ISO 6252:1992) |
| EN ISO 6259-1-2001 | 热敏塑料管 拉伸性能的测定 第1部分：一般测试方法 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:1997) |
| EN ISO 6402-1-2002 | 塑料 丙烯腈-苯乙烯-丙烯酸脂(ASA)、丙烯腈-(乙烯-丙烯-二烯烃)-苯乙烯(AEPDS)和丙烯腈-(氯化聚乙烯)-苯乙 | Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 1: Designation system and basis for specification |
| EN ISO 6402-2-1999 | 塑料 耐冲击丙烯腈/苯乙烯模塑和挤塑材料(ASE,AES,ACS),丁二烯改型除外 第２部分：试验样品的准备与性能 | Plastics - Impact-resistant acrylonitrile/styrene (ASA, AES, ACS) moulding and extrusion materials, excluding butadiene-modified materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:1994) |
| EN ISO 6427-1998 | 塑料 有机溶剂萃取物的测定(常规法) | Plastics - Determination of matter extractable by organic solvents (conventional methods) (ISO 6427:1992) |
| EN ISO 6603-1-2000 | 塑料 硬质塑料冲孔性能的测定 第1部分：非仪器冲击试验 | Plastics - Determination of puncture impact behaviour of rigid plastics - Part 1: Non-instrumented impact testing (ISO 6603-1:2000) |
| EN ISO 6603-2-2000 | 塑料 硬质塑料冲孔性能的测定 第2部分：仪器冲击试验 | Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented puncture test (ISO 6603-2:2000) |
| EN ISO 6721-1-2002 | 塑料 动态机械性能的测定 第1部分：一般原则 | Plastics - Determination of dynamic mechanical properties - Part 1: General principles (ISO 6721-1:2001) |
| EN ISO 6721-2-1996 | 塑料 动态机械性能的测定 第2部分：扭摆法 | Plastics - Determination of dynamic mechanical properties - Part 2: Torsion-pendulum method (ISO 6721-2:1994, including Technical Corrigendum 1:1995) |
| EN ISO 6721-3-1996 | 塑料 动态机械性能的测定 第3部分：弯曲振动 共振法 | Plastics - Determination of dynamic mechanical properties - Part 3: Flexural vibration - Resonance-curve method (ISO 6721-3:1994, including Technical Corrigendum 1:1995) |
| EN ISO 6803-1997 | 橡胶或塑料软管和软管组件 无弯曲的液压脉冲试验 | Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803:1994) |
| EN ISO 6808-2000 | 给排油用塑料软管和软管组件 规范 | Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification (ISO 6808:1999) |
| EN ISO 7214-2000 | 泡沫塑料 聚乙烯 试验方法 | Cellular plastics - Polyethylene - Methods of test (ISO 7214:1998) |
| EN ISO 7233-1995 | 橡胶和塑料软管和软管组件 耐真空性能测定 | Rubber and plastics hoses and hose assemblies - Determination of suction resistance (ISO 7233:1991) |
| EN ISO 7327-1997 | 塑料 环氧树脂用固化剂和促进剂 酸酐中游离酸测定 | Plastics - Hardeners and accelerators for epoxide resins - Determination of free acid in acid anhydride (ISO 7327:1994) |
| EN ISO 7391-1-1999 | 塑料 聚碳酸酯模塑和挤塑材料 第1部分：命名体系和基本规范 | Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 7391-1:1996) |
| EN ISO 7391-2-1999 | 塑料 聚碳酸酯模塑和挤塑材料 第2部分：试样制备和特性测定 | Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7391-2:1996) |
| EN ISO 75-1-1996 | 塑料 载荷下挠曲温度的测定 第1部分：一般试验方法 | Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:1993) |
| EN ISO 75-2-1996 | 塑料 载荷下挠曲温度的测定 第2部分：塑料与硬橡胶 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:1993) |
| EN ISO 75-3-1996 | 塑料 载荷下挠曲温度的测定 第3部分：高强度热固性叠层板和长纤维增强塑料 | Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:1993) |
| EN ISO 7662-1996 | 橡胶和塑料软管 衬里耐磨性的测定 | Rubber and plastics hoses - Determination of abrasion of lining (ISO 7662:1988) |
| EN ISO 7751-1997 | 橡胶和塑料软管和软管组件 试验压力和爆破压力对设计工作压力的比值 | Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to design working pressure (ISO 7751:1991) |
| EN ISO 7808-1998 | 塑料 热固性模塑材料 传递流动性的测定 | Plastics - Thermosetting moulding materials - Determination of transfer flow (ISO 7808:1992) |
| EN ISO 7822-1999 | 玻璃纤维增强塑料 孔隙率的测定 烧失量、机械粉碎和静态计数法 | Textile glass reinforced plastics - Determination of void content - Loss on ignition, mechanical disintegration and statistical counting methods (ISO 7822:1990) |
| EN ISO 7823-1-2003 | 塑料 聚甲基丙烯酸甲脂板材 类型、尺寸和特性 第1部分：浇注薄板材 | Plastics - Poly(methyl methacrylate) sheets; Types, dimensions and characteristics - Part 1: Cast sheets (ISO 7823-1:2003) |
| EN ISO 7823-2-2003 | 塑料 聚甲基丙烯酸甲脂板材 类型、尺寸和特性 第2部分：挤塑片 | Plastics - Poly(methyl methacrylate) sheets; Types, dimensions and characteristics - Part 2: Extruded sheets (ISO 7823-2:2003) |
| EN ISO 7854-1997 | 橡胶或塑料涂覆织物 耐弯曲损坏性的测定 | Rubber- or plastics-coated fabrics - Determination of resistance to damage by flexing (ISO 7854:1995) |
| EN ISO 8028-2000 | 真空喷涂漆用橡胶和／或塑料软管和软管组件 规范 | Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO 8028:1999) |
| EN ISO 8030-1997 | 橡胶和塑料软管 易燃烧性试验方法 | Rubber and plastics hoses - Method of test for flammability (ISO 8030:1995) |
| EN ISO 8031-1997 | 橡胶和塑料软管和软管组件 电阻率测定 | Rubber and plastics hoses and hose assemblies - Determination of electrical resistance (ISO 8031:1993) |
| EN ISO 8032-1999 | 橡胶和塑料软管和软管组件 液压脉冲弯曲试验(半欧姆型试验) | Rubber and plastics hose assemblies - Flexing combined with hydraulic impulse test (half-omega test) (ISO 8032:1997) |
| EN ISO 8256-1996 | 塑料 拉伸冲击强度测定 包括技术勘误1 | Plastics - Determination of tensile-impact strength (ISO 8256:1990, including Technical Corrigendum 1:1991) |
| EN ISO 8308-1995 | 橡胶和塑料软管和管件 液体透过管壁性能测定 | Rubber and plastics hoses and tubing - Determination of transmission of liquids through hose and tubing walls (ISO 8308:1993) |
| EN ISO 8330-2000 | 橡胶和塑料软管和软管组件 词汇 | Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:1998) |
| EN ISO 845-1995 | 泡沫塑料和橡胶 表观密度的测定 | Cellular plastics and rubbers - Determination of apparent (bulk) density (ISO 845:1988) |
| EN ISO 846-1997 | 塑料 微生物作用的评价 | Plastics - Evaluation of the action of microorganisms (ISO 846:1997) |
| EN ISO 8580-1995 | 橡胶与塑料软管 稳定状态下耐紫外线的测定 | Rubber and plastic hoses - Determination of ultra-violet resistance under static conditions (ISO 8580:1987) |
| EN ISO 8618-1998 | 塑料 液态酚醛树脂 非挥发性物质的常规测定 | Plastics - Liquid phenolic resins - Conventional determination of non-volatile matter (ISO 8618:1995) |
| EN ISO 8619-1998 | 塑料 酚醛树脂粉 在加热玻璃盘上流动距离的测定 | Plastics - Phenolic resin powder - Determination of flow distance on a heated glass plate (ISO 8619:1995) |
| EN ISO 8620-1995 | 塑料 酚醛树脂粉 筛析 用喷气筛设备进行过滤分析 | Plastics - Phenolic resin powder - Sieve analysis - Sieve analysis using air-jet sieve apparatus (ISO 8620:1986) |
| EN ISO 868-2003 | 塑料与硬质橡胶 用硬度计测定压痕硬度［肖氏(SHORE)硬度］ | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) |
| EN ISO 877-1996 | 塑料 玻璃板下日光暴晒耐老化及性能测定 | Plastics - Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and to intensified weathering by daylight using Fresnel mirrors (ISO 877:1994) |
| EN ISO 8795-2001 | 人类生活用水输送用塑料管道系统 迁移评定 塑料管道迁移值的测定 | Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints (ISO 8795:2001) |
| EN ISO 8974-2002 | 塑料 酚醛树脂 用气体色谱法测定残余酚含量 | Plastics - Phenolic resins - Determination of residual phenol content by gas chromatography (ISO 8974:2002) |
| EN ISO 8975-1995 | 塑料 酚醛树脂 pH值的测定 | Plastics - Phenolic resins - Determination of pH (ISO 8975:1989) |
| EN ISO 8985-1998 | 塑料 乙烯／乙酸乙烯共聚物(EVAC)热塑塑料 乙酸乙烯含量的测定 | Plastics - Ethylene/vinyl acetate copolymer (EVAC) thermoplastics - Determination of vinyl acetate content (ISO 8985:1998) |
| EN ISO 8986-1-1999 | 塑料 聚丁烯模塑和挤塑材料 第1部分：命名体系和基本规范 | Plastics - Polybutene (PB) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 8986-1:1993) |
| EN ISO 8986-2-1995+A1-2000 | 塑料 聚丁烯模塑和挤塑材料 第2部分：试样的制备和特性的测定 | Plastics - Polybutene (PB) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8986-2:1995) |
| EN ISO 8987-1998 | 塑料 酚醛树脂 在Ｂ转变试验板上的活化性能的测定 | Plastics - Phenolic resins - Determination of reactivity on a B-transformation test plate (ISO 8987:1995) |
| EN ISO 8988-1997 | 塑料 酚醛树脂 六次甲基四胺含量的测定 凯氏法和过氯酸法 | Plastics - Phenolic resins - Determination of hexamethylenetetramine content - Kjeldahl method and perchloric acid method (ISO 8988:1995) |
| EN ISO 8989-1998 | 塑料 液态酚醛树脂 水溶物的测定 | Plastics - Liquid phenolic resins - Determination of water miscibility (ISO 8989:1995) |
| EN ISO 899-1-2003 | 塑料 蠕变的测定 第1部分：拉伸蠕变 | Plastics - Determination of creep behaviour - Part 1: Tensile creep (ISO 899-1:2003) |
| EN ISO 899-2-2003 | 塑料 蠕变的测定 第2部分：用三点负载测定扰屈蠕变 | Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2003) |
| EN ISO 9054-1999 | 硬质泡沫塑料 自结皮高密度材料的试验方法 | Cellular plastics, rigid - Test methods for self-skinned, high-density materials (ISO 9054:1990) |
| EN ISO 9080-2003 | 塑料管与管道系统 用推断法测定热塑管型材料长期流动液体静力强度 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2003) |
| EN ISO 9311-2-2002 | 热塑性塑料管系统的粘合剂 第2部分：切变强度的测定 | Adhesives for thermoplastics piping systems - Part 2: Determination of shear strength (ISO 9311-2:2002) |
| EN ISO 9396-2000 | 塑料 酚醛树脂 用自动装置在给定温度下对凝胶时间的测定 | Plastics - Phenolic resins - Determination of the gel time at a given temperature using automatic apparatus (ISO 9396:1997) |
| EN ISO 9397-1997 | 塑料 酚醛树脂 游离甲醛含量的测定 盐酸胲法 | Plastics - Phenolic resins - Determination of free-formaldehyde content - Hydroxylamine hydrochloride method (ISO 9397:1995) |
| EN ISO 960-1997 | 塑料 聚酰胺(PA) 水含量的测定 | Plastics - Polyamides (PA) - Determination of water content (ISO 960:1988) |
| EN ISO 9702-1998 | 塑料 胺类环氧固化剂 伯、仲和叔胺基团氨含量的测定 | Plastics - Amine epoxide hardeners - Determination of primary, secondary and tertiary amine group nitrogen content (ISO 9702:1996) |
| EN ISO 9771-1997 | 塑料 酚醛树脂 在酸性条件处理时液体酚醛树脂假绝热温升的测定 | Plastics - Phenolic resins - Determination of the pseudo-adiabatic temperature rise of liquid resols when cured under acid conditions (ISO 9771:1995) |
| EN ISO 9773-1998+A1-2003 | 塑料 立式软薄试样与小火焰源接触的燃烧性能测定 | Plastics - Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source (ISO 9773:1998) / Note: To be amended by EN ISO 9773/prA1 (2003-04). |
| EN ISO 9944-1995 | 塑料 酚醛树脂 树脂萃取物电导率的测定 | Plastics - Phenolic resins - Determination of electrical conductivity of resin extracts (ISO 9944:1990) |
| EN ISO 9967-1995 | 塑料管 蠕变系数的测定 | Plastics pipes - Determination of creep ratio (ISO 9967:1994) |
| EN ISO 9969-1995 | 热塑性塑料管 环型硬度的测定 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:1994) |
| ENV 1046-2001 | 塑料管道和导管系统 运输水或污水用建筑结构外系统 地上和地下安装用规程 | Plastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for installation above and below ground |
| ENV 12108-2001 | 塑料管道系统 在建筑物内安装家用冷热压力管道系统的指南 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ENV 13130-1-1999 | 接触食品的材料和物品 受限塑料物质 第1部分：从塑料进入食物和食物模拟物的物质迁移的试验方法以及物质 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 1: Guide to the test methods for the specific migration of substances from plastics into foods and food simulants and the determination of substances in Plastics and the Selection of Conditions of Exposure to Food Simulants |
| ENV 13130-2-1999 | 接触食品的材料和物品 受限塑料物质 第2部分：食物模拟物中苯二甲酸的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 2: Determination of terephthalic acid in food simulants |
| ENV 13130-3-1999 | 接触食品的材料和物品 受限塑料物质 第3部分：食物和食物模拟物中氰乙烯测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 3: Determination of acrylonitrile in food and food simulants |
| ENV 13130-4-1999 | 接触食品的材料和物品 受限塑料物质 第4部分：塑料中1-丁二烯、3-丁二烯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 4: Determination of 1,3-butadiene in plastics |
| ENV 13130-5-1999 | 接触食品的材料和物品 受限塑料物质 第5部分：食物模拟物中氯二乙烯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 5: Determination of vinylidene chloride in food simulants |
| ENV 13130-6-1999 | 接触食品的材料和物品 受限塑料物质 第6部分：塑料中氯二乙烯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 6: Determination of vinylidene chloride in plastics |
| ENV 13130-7-1999 | 接触食品的材料和物品 受限塑料物质 第7部分：食物模拟物中单甘醇和二甘醇的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 7: Determination of monoethylene glycol and diethylene glycol in food simulants |
| ENV 13130-8-1999 | 接触食品的材料和物品 受限塑料物质 第8部分：塑料中异氰酸盐的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 8: Determination of isocyanates in plastics |
| ENV 1329-2-2001 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 硬塑聚氯乙烯(PVC-U) 第2部分：合格平定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity |
| ENV 13801-2000 | 建筑物中用于粪便和污水排放（低温和高温）的塑料管道系统 热塑性塑料 推荐的安装规范 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation |
| ENV 1401-2-2000 | 非压力地下污废水排放用塑料管道系统硬聚氯乙烯(PVC-U) 第2部分：合格评定 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for assessment of conformity |
| ENV 1401-3-2001 | 非压力地下污废水排放用塑料管道系统 硬聚氯乙烯(PVC-U) 第3部分：安装指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation |
| ENV 1451-2-2001 | 建筑物结构内污物和污水排出(低和高温)用塑料管道系统 聚丙烯(PP ) 第2部分：合格评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity |
| ENV 1452-6-2001 | 供水塑料管道系统 硬塑聚氯乙烯(PVC-U) 第6部分：安装指南 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Guidance for installation |
| ENV 1452-7-2000 | 供水塑料管道系统 硬聚氯乙烯(PVC-U) 第7部分：合格评定指南 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 7: Guidance for the assessment of conformity |
| ENV 1453-2-2000 | 建筑物内污物和废水排放(低和高温)带结构壁管道的塑料管道系统 硬聚氯乙烯(PVC-U) 第2部分：合格评定指南 | Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity |
| ENV 1455-2-2001 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 丙烯腈 丁二烯 苯乙烯共聚物 第2部分：合格证评 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Guidance for the assessment of conformity |
| ENV 1519-2-2001 | 建筑物结构内污物和污水排放(低和高温)塑料管道系统 聚已烯(PE) 第2部分：合格评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity |
| ENV 1565-2-2001 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 苯乙烯共聚混合物(SAN+PVC) 第2部分：合格评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 2: Guidance for the assessment of conformity |
| ENV 1566-2-2001 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 氯化聚偏氯乙烯(PVC-C) 第2部分：合格评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly (vinyl chloride) (PVC-C) - Part 2: Guidance for the assessment of conformity |
| ENV 1852-2-2000 | 无压地下排水和污水用塑料管道系统 聚丙烯(PP) 第2部分：合格评定指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity |
| ENV 852-2001 | 运输人类用水的塑料管道系统 移动评估 源自移动值的实验室说明指南 | Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Guidance on the interpretation of laboratory derived migration values |
| prEN 1016-1993 | 塑料管道系统 非可塑聚氯乙烯一端受载的双孔接头 弯曲和内部压力时的密封性和强度试验方法 | Plastics piping systems; unplasticized poly(vinyl chloride) (PVC-U) end-load bearing double socket joints; test method for leaktightness and strength while subjected to bending and internal pressure |
| prEN 1042-1995 | 塑料管道系统 聚烯烃管和/或配件间的熔接连接件 恒温下内部压力抵抗力的测定 | Plastics piping systems - Fusion joints between polyolefin pipes and/or fittings - Determination of resistance to internal pressure at constant temperature |
| prEN 1115-2-1997 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第2部分：具挠 | Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints |
| prEN 1115-4-1993 | 压力下地下排水和排污装置用塑料管道系统 基于聚脂树脂的玻璃增强热固性塑料（GRP） 第4部分：辅助设备 | Plastics piping systems for underground drainage and sewerage under pressure; glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP); part 4 (informative): ancillary equipment |
| prEN 1115-6-1997 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第6部分：安装 | Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 6: Practices for installation |
| prEN 1115-7-1995 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第7部分：一致 | Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 7: Assessment of conformity |
| prEN 1220-1993 | 塑料材料的卫生用具 冲击性试验 | Sanitary appliances of plastic materials; impact test |
| prEN 12666-1-2001 | 非压力地下排水和排污用塑料管道系统 聚乙烯（PE）.第1部分：管道、配件和系统规范 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| prEN 12917-1997 | 玻璃纤维加强塑料（GRP）制地下罐 用于液体石油燃料无压贮存的卧式柱罐 EN976-1和EN976-3的符合性评价 | Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Assessment of conformity to EN 976-1 and EN 976-3 |
| prEN 1297-2001 | 防水挠性薄板、屋顶防水用沥青、塑料和橡胶薄板 长期暴露在紫外光辐射的高温和水综合环境下的人工老化方法 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Method of artificial ageing by long term exposure to the combination of UV radiation, elevated temperature and water |
| prEN 13100-2-2002 | 热塑性塑料半成品焊接接头的无损检验 第2部分：X射线检查法 | Non destructive testing of welded joints of thermoplastics semi-finished products - Part 2: X-ray radiographic testing |
| prEN 13100-3-2002 | 热塑性塑料半成品焊接接头的无损检验 第3部分：超声检测 | Non destructive testing of welded joints of thermoplastics semi-finished products - Part 3: Ultrasonic testing |
| prEN 131600-1992 | 分规范：纸或纸/塑料介质固定电容器 | Sectional specification: fixed capacitors with paper or paper/plastic dielectrics |
| prEN 131601-1992 | 空白详细规范：纸或纸/塑料介质固定电容器 | Blank detail specification: fixed capacitors with paper or paper/plastic dielectrics |
| prEN 13245-1998 | 塑料 建筑物用非增塑聚氯乙烯（PVC-U）型材 名称和规范基础 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Designation and basis for specification |
| prEN 1329-3-1998 | 建筑物结构内污物和废水排放（低和高温）用塑料管道系统 硬塑聚氯乙烯（PVCU) 第3部分：安装指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation |
| prEN 1329-5-1994 | 建筑物结构内污物和废水排放（低和高温）用塑料管道系统 硬塑聚氯乙烯（PVCU) 第5部分：对系统用途的适宜 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 5: fitness for purpose of the system |
| prEN 1329-6-1994 | 建筑物结构内污物和废水排放（低和高温）用塑料管道系统 硬塑聚氯乙烯（PVC-U）.第6部分：推荐的安装实践 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Recommended practice for installation |
| prEN 1336-1993 | 塑料管道系统 热塑性压力管道用终端承载和无承开组件和接头 内部水压力下长期密封性试验方法 | Plastics piping systems; end-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping; test method for long-term leaktightness under internal water pressure |
| prEN 13418-1999 | 橡胶和塑料机械 薄膜或板材卷绕机 安全要求 | Rubber and plastics machines - Winding machines for film or sheet - Safety requirements |
| prEN 13421-1999 | 塑料 热塑复合物 合成材料和加强纤维 用于测定压塑复合材料性能各向异性的样品制备 | Plastics - Thermoset moulding compounds - Composites and reinforcement fibres - Preparation of specimens for determining the anisotropy of the properties of compression moulding composites |
| prEN 13476-1-2002 | 非压力地下排水和污水热塑性塑料管道系统 聚氯乙烯（PVC-U）、聚丙烯（PP）)和聚已烯（PE）的结构墙管道系 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for pipes, fittings and the syste |
| prEN 13566-2-2002 | 用于修复非压力排水和污水网的塑料管道系统 第2部分：带连续管的衬套 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes |
| prEN 13705-1999 | 热塑性塑料的焊接 热气流焊的机器和设备（包括挤压焊） | Welding of thermoplastics - Machines and equipment for hot gas welding (including extrusion welding) |
| prEN 13897-2000 | 挠性防水板 沥青.塑料和橡胶屋面防水板 低温下拉伸后防水性的测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of watertightness after stretching at low temperature |
| prEN 13923-2000 | 绕制玻璃纤维加强塑料（FRP）压力容器 材料、设计、计算、制造和试验 | Filament wound FRP pressure vessels - Materials, design, calculation, manufacturing and testing |
| prEN 13948-2000 | 柔性防水板 防水用的沥青、塑料和橡胶层 底部防渗水性的测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to root penetration |
| prEN 13956-2000 | 柔性防水板 屋面防水用的塑料板和橡胶板 特性和定义 | Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Definitions and characteristics |
| prEN 13967-2000 | 柔性防水板 塑料和橡胶防潮薄膜包括塑料和橡胶基防水膜 .定义和特性 | Flexible sheets for waterproofing - Plastic and rubber damp proof membranes including plastic and rubber basement tanking membranes - Definitions and characteristics |
| prEN 13969-2000 | 柔性防水板 沥青防潮薄膜包括塑料和橡胶基防水薄膜 定义和特性 | Flexible sheets for waterproofing - Bitumen damp proof membranes including plastic and rubber basement tanking membranes - Definitions and characteristics |
| prEN 13984-2000 | 柔性防水板 塑料和橡胶蒸汽隔离层 定义和特性 | Flexible sheets for waterproofing - Plastic and rubber vapour control layers - Definitions and characteristics |
| prEN 1401-5-1994 | 非压力地下污废水排放用塑料管道系统 硬聚氯乙烯(PVC-U) 第5部分：使用系统的适合性 | Plastics piping systems for non-pressure underground drainage and sewerage; unplasticized poly(vinyl chloride) (PVC-U); part 5: fitness for purpose of the system |
| prEN 14280-2001 | 地下电缆管道的塑料管线系统 未增塑聚氯乙烯 塑料管、管件及管线规范 | Plastics piping systems for buried cable ducting - Unplasticized poly(vinyl chloride) (PVC-U) - Specifications for pipes, fittings and the system |
| prEN 14281-2001 | 地下电缆管道的塑料管线系统 聚乙烯 塑料管、管件及管线规范 | Plastics piping systems for buried cable ducting - Polyethylene (PE) - Specifications for pipes, fittings and the system |
| prEN 14282-2001 | 地下电缆管道的塑料管线系统 聚丙烯 塑料管、管件及管线规范 | Plastics piping systems for buried cable ducting - Polypropylene (PP) - Specifications for pipes, fittings and the system |
| prEN 14283-2001 | 一般用途地下管道的塑料管线系统 未增塑聚氯乙烯 塑料管、管件及管线规范 | Plastics piping systems for general purpose buried ducting - Unplasticized poly(vinyl chloride) (PVC-U) - Specifications for pipes, fittings and the system |
| prEN 14284-2001 | 一般用途地下管道的塑料管线系统 聚乙烯 塑料管、管件及管线规范 | Plastics piping systems for general purpose buried ducting - Polyethylene (PE) - Specifications for pipes, fittings and the system |
| prEN 14285-2001 | 一般用途地下管道的塑料管线系统 聚丙烯 塑料管、管件及管线规范 | Plastics piping systems for general purpose buried ducting - Polypropylene (PP) - Specifications for pipes, fittings and the system |
| prEN 14364-2002 | 有或无压排水和排污塑料管线系统 玻璃纤维增强的未饱和的聚酯树脂基热固塑料管 塑料管管件及接头规范 | Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints |
| prEN 14401-2002 | 硬质塑料容器 封闭能力的试验 | Rigid plastics containers - Methods to the effectiveness of closures |
| prEN 14408-1-2002 | 地下供气管网的改造用塑料管线系统 第1部分：总则 | Plastics piping systems for the renovation of underground gas supply networks - Part 1: General |
| prEN 14408-3-2002 | 地下供气管网的改造用塑料管线系统 第3部分：紧贴管子的衬套 | Plastics piping systems for the renovation of underground gas supply networks - Part 3: Lining with close-fit-pipes |
| prEN 14409-1-2002 | 地下供气管网的改造用塑料管线系统 第1部分：总则 | Plastics piping systems for the renovation of underground water supply networks - Part 1: General |
| prEN 14409-3-2002 | 地下供水管网的改造用塑料管线系统 第3部分：紧贴管子的衬套 | Plastics piping systems for the renovation of underground water supply networks - Part 3: Lining with close-fit-pipes |
| prEN 14447-2002 | 纤维增强塑料 玻璃垫增强热塑塑料 液动性和固化测定 | Fibre reinforced plastics - Glass mat reinforced thermoplastics (GMT) - Determination of flowability and solidification |
| prEN 14448-2002 | 大规模生产中热塑性模塑料的热工具焊接 | Heated tool welding of thermoplastics mouldings in mass production |
| prEN 14471-2002 | 烟囱 塑料烟衬里的烟囱系统的试验方法和要求 | Chimneys - Requirements and test methods for system chimneys with plastic flue liners |
| prEN 1451-3-1994 | 建筑物结构内用于污物和污水排放（高/低温）的塑料管道系统 聚丙烯（PP） 第3部分：管件 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 3: Fittings |
| prEN 1451-5-1994 | 建筑物结构内用污物和污水排放（高/低温）的塑料管道系统 聚丙烯（PP） 第5部分：系统用途的适合性 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 5: Fitness for purpose of the system |
| prEN 1451-6-1994 | 建筑物结构内用于污物和污水排放（高/低温）的塑料管道系统 聚丙烯（PP) 第6部分：推荐的安装实践 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building - Polypropylene (PP) - Part 6: Recommended practice for installation |
| prEN 1453-3-1998 | 建筑物内污物和废水排放(低和高温)带结构壁管道的塑料管道系统 硬聚氯乙烯(PVC-U) 第3部分：安装指南 | Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation |
| prEN 1453-5-1994 | 建筑物内污物和废水排放(低和高温)带结构壁管道的塑料管道系统 硬聚氯乙烯(PVC-U) 第5部分：系统用管件 | Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 5: fittings for purpose of the system |
| prEN 1453-6-1994 | 建筑物内污物和废水排放(低和高温)带结构壁管道的塑料管道系统 硬聚氯乙烯(PVC-U) 第6部分：推荐安装实践 | Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 6: recommended practice for installation |
| prEN 1455-3-1994 | 建筑物结构内用于污物和污水排放（高/低温）的塑料管道系统 丙烯晴 丁二烯 苯已烯共聚物(ABS) 第3部分 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 3: Fittings |
| prEN 1455-5-1994 | 建筑物结构内用于污物和污水排放（高/低温）的塑料管到系统 丙烯晴 丁二烯 苯已烯共聚物(ABS) 第5部分 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 5: Fitness for purpose of the system |
| prEN 1455-6-1994 | 建筑物结构内用于污物和污水排放（高/低温）的塑料管道系统 丙烯晴 丁二烯 苯已烯共聚物(ABS) 第6部分 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building - Acrylonitrile-butadiene-styrene (ABS) - Part 6: Recommended practice for installation |
| prEN 1456-3-1994 | 地上和地下污废水压力排放用塑料管道系统 硬已烯(聚氯已烯)(PVC-U) .第3部分：管件 | Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings |
| prEN 1456-4-1994 | 地上和地下污废水压力排放用塑料管道系统 硬已烯(聚氯已烯)(PVC-U) 第4部分：阀门及辅助设备 | Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment |
| prEN 1456-5-1994 | 地上和地下污废水压力排放用塑料管道系统 硬已烯(聚氯已烯)(PVC-U) 第5部分：对系统用途的适宜性 | Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5: Fitness for purpose of the system |
| prEN 1456-6-1994 | 地上和地下污废水压力排放用塑料管道系统 硬已烯(聚氯已烯)(PVC-U) 第6部分：推荐的安装实践 | Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Recommended practice for installation |
| prEN 1519-3-1994 | 建筑物结构内污物和污水排放(低和高温)塑料管道系统 聚已烯(PE) 第3部分：管件 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 3: Fittings |
| prEN 1519-5-1994 | 建筑物结构内污物和污水排放(低和高温)塑料管道系统.聚已烯(PE) 第5部分：针对系统用途的适合性 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| prEN 1519-6-1995 | 建筑物结构内污物和污水排放(低和高温)塑料管道系统 聚已烯(PE) 第6部分：推荐的安装实践 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 6: Recommanded practice for installation |
| prEN 1548-2000 | 防水的挠性薄板 涂覆沥青的方法 屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Method for exposure to bitumen - Plastic and rubber sheets for roof waterproofing |
| prEN 1555-6-1995 | 供给气体燃料用塑料管道系统 聚已烯(PE) 第6部分：推荐的安装实践 | Plastics piping systems for gaseous fuels supply - Polyethylene (PE) - Part 6: Recommended practice for installation |
| prEN 1565-3-1994 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 苯乙烯共聚混合物(SAN+PVC) 第3部分：管件 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 3: Fittings |
| prEN 1565-5-1994 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 苯乙烯共聚混合物(SAN+PVC) 第5部分：针对系统用途 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 5: Fitness for purpose of the system |
| prEN 1565-6-1995 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 苯乙烯共聚混合物(SAN+PVC) 第6部分：推荐的安装实 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN + PVC) - Part 6: Recommended practice for installation |
| prEN 1566-3-1994 | 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 氯化聚偏氯乙烯(PVC-C) 第3部分：管件 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings |
| prEN 1566-5-1994 | 建筑物结构内污物和污水排放(低和高温)用塑料管道系统 氯化已烯(聚氯已烯)(PVC-C) 第5部分：针对系统用途 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system |
| prEN 1636-1-1996 | 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第1部分：总则 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 1: General |
| prEN 1636-2-1996 | 无压力排水道和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第2部分：带有挠 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints |
| prEN 1636-4-1994 | 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第4部分：辅助设备 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 4: Ancillary equipment |
| prEN 1796-2-1995 | 有或无压力供水用塑料管道系统 非饱和性聚脂树脂基玻璃增强热固性塑料 第2部分：带挠性、缩口活节或刚性 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints |
| prEN 1796-2003 | 有或无压力供水用塑料管道系统 非饱和性聚脂树脂基玻璃增强热固性塑料 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) |
| prEN 1796-3-1995 | 有或无压力供水用塑料管道系统聚合物树脂（UP）基玻璃纤维增强热固性塑料（GRP） 第3部分：管件 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 3: Fittings |
| prEN 1796-4-1995 | 有或无压力供水有塑料管道系统聚合物树脂（UP）基玻璃纤维增强热固性塑料（GRP） 第4部分：辅助设备 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 4: Ancillary equipment |
| prEN 1796-5-1995 | 有或无压力供水用塑料管道系统聚合物树脂（UP）基玻璃纤维增强热固性塑料（GRP） 第5部分：系统用途的适合 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 5: Fitness for the purpose of the system |
| prEN 1796-6-1995 | 有或无压力供水用塑料管道系统聚合物树脂（UP）基玻璃纤维增强热固性塑料（GRP） 第6部分：推荐的安装实践 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 6: Recommended practice for installation |
| prEN 1840-1995 | 结构粘合剂 塑料表面制备指南 | Structural adhesives - Guidelines for the surface preparation of plastics |
| prEN 1851-2-1995 | 挠性防水薄板 接缝强度的测定 第2部分：屋顶防水用热塑塑料和人造橡胶板 | Flexible sheets for waterproofing - Determination of joint strength - Part 2: Thermoplastic and elastomeric sheets |
| prEN 1852-5-1995 | 无压地下排水和污水用塑料管道系统 聚炳烯(PP) 第5部分：对系统配合的适宜性 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 5: Fitness for purpose of the system |
| prEN 1873-1999 | 屋顶覆盖物 带竖立支架的单个塑料天窗 | Roof coverings - Individual rooflights of plastics with upstands |
| prEN 2823-1998 | 航空航天系列 纤维增强塑料 暴露于潮湿环境对物理和机械性能影响的测定 | Aerospace series - Fibre reinforced plastics - Determination of the effect of exposure to humid atmosphere on physical and mechanical characteristics |
| prEN 289-2000 | 橡胶和塑料机械 压力机 安全要求 | Rubber and plastics machines - Presses - Safety requirements |
| prEN 301-2001 | 承重木结构用胶接酚醛塑料和氨基塑料 分类和性能要求 | Adhesives, phenolic and aminoplastic, for load-bearing timber structures - Classification and performance requirements |
| prEN 3475-513-2001 | 航空航天系列 飞行器用的电缆 试验方法 第513部分：变形阻力（与塑料电缆捆接时） | Aerospace series - Cables, electrical, aircraft use; Test methods - Part 513: Deformation resistance (Installation with plastic cable ties) |
| prEN 3545-002-2002 | 航空航天系列 尾部密封和无密封 塑料护套、锁紧装置、操作温度5℃到175℃的矩形电接点 第002部分：性能 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55℃ to 175℃ - Part 002: Specification of performance and contact arrangements |
| prEN 3615-1998 | 航空航天系列 纤维增强塑料 暴露于潮湿环境和水分吸收条件的测定 | Aerospace series - Fibre reinforced plastics - Determination of the conditions of exposure to humid atmosphere and of moisture absorption |
| prEN 4238-1998 | 航空航天系列 纤维增强塑料 干热对物理和机械特性的影响的测定 | Aerospace series - Fibre reinforced plastics - Determination of the effect of dry heat on physical and mechanical characteristics |
| prEN 762-1995 | 塑料管道和导管系统 热塑系统用弹性密封接头 密封环保持力和损坏的试验方法 | Plastics piping and ducting systems - Joints with elastomeric seals for thermoplastic systems - Test method for retention of, and damage to, sealing rings |
| prEN 976-3-1997 | 玻璃增强塑料地下贮罐 非压力存储液体石油燃料水平园柱状贮罐 第3部分：双壁贮罐的要求和试验方法 | Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Part 3: Requirements and test methods for double wall tanks |
| prEN 976-4-1997 | 玻璃增强塑料地下贮罐 非压力存储液体石油燃料水平园柱状贮罐 第4部分：双壁贮罐的运输、储存、操作和安 | Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Part 4: Transport, handling, storage and installation of double wall tanks |
| prEN 987-1995 | 塑料管道和导管系统 铸模装置 装置中磨掉碎片摆锤式冲击试验强度的测定 | Plastics piping and ducting systems - Injection-moulded fittings - Determination of the Charpy impact strength of test pieces cut from a fitting |
| prEN ISO 10351-1996 | 塑料 用125mm火焰测定样品可燃性 | Plastics - Determination of the combustibility of specimens using a 125 mm flame source (ISO/DIS 10351:1996) |
| prEN ISO 10366-2-2003 | 塑料 甲基丙烯酸甲酯/丙烯腈/丁二烯/苯乙烯(MABS)模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO/FDIS 10366-2:2003) / Note: Intended as replacement for EN ISO 10366-2 (199 |
| prEN ISO 10468-1999 | 塑料管 玻璃纤维增增强热固塑料管 在湿环境中长期特殊环形蠕变劲度的测定及湿蠕变因子的计算 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor (ISO/DIS 10468:1999) |
| prEN ISO 1133-2003 | 塑料 熔体质量流动速率(MFR)和熔体体积流动速率(MFR)的测定 | Plastics - Determination of the melt-mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO/DIS 1133:2003) / Note: Intended as replacement for EN ISO 1133 (1999-05). |
| prEN ISO 11337-2001 | 塑料 酰胺 用气相色谱法测定e-已内酰胺和w-月桂内酰胺 | Plastics - Polyamides - Determination of e-caprolactam and w-laurolactam by gas chromatography (ISO/DIS 11337:2001) |
| prEN ISO 11403-2-2002 | 塑料 可比多点数据的采集和表示 第2部分：热和加工性能 | Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO/DIS 11403-2:2002) |
| prEN ISO 1183-1-2003 | 塑料 非泡沫塑料的密度测定方法 第1部分：浸液方法 液体比重瓶法和滴定法 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO/FDIS 1183-1:2003) |
| prEN ISO 1183-4-1998 | 塑料 非泡沫塑料的密度测定方法 第4部分：气体比重瓶法 | Plastics - Methods for determining the density of non-cellular plastics - Part 4: Gas pyknometer method (ISO/DIS 1183-4:1998) |
| prEN ISO 1210-1996 | 塑料 在与小火源接触中水平与垂直样品燃烧性能的测定 | Plastics - Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source (ISO/DIS 1210:1996) |
| prEN ISO 14828-1999 | 塑料管道系统 玻璃纤维增强热固塑料管 在湿环境下长期特殊环形松弛劲度的测定和湿松弛系数的计算 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor (ISO/DIS 14828:1999) |
| prEN ISO 15508-2000 | 塑料 无支撑的挤制和/或压延的增塑聚氯乙烯(PVC-P)塑料薄膜或薄板材 命名的基本原理及试验方法 | Plastics - Film or sheeting of plasticizied poly(vinyl chloride) (PVC-P) extruded and/or calendered, unsupported - Basis for designation and test methods (ISO/DIS 15508:2000) |
| prEN ISO 15874-1-2002 | 冷热水用塑料管道系统 聚乙烯（PE） 第1部分：总则 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO/FDIS 15874-1:2002) |
| prEN ISO 15874-2-2002 | 冷热水用塑料管道系统 聚丙烯（PP） 第2部分：管道 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO/FDIS 15874-2:2002) |
| prEN ISO 15874-3-2002 | 冷热水用塑料管道系统 聚丙烯（PP） 第3部分：配件 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings (ISO/FDIS 15874-3:2002) |
| prEN ISO 15874-5-2002 | 冷热水用塑料管道系统 聚丙烯（PP） 第5部分：系统目的的适配性 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO/FDIS 15874-5:2002) |
| prEN ISO 15875-1-2002 | 冷热水塑料管道系统 交联聚乙稀（ PE - X ） 第1部分：总则 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General (ISO/FDIS 15875-1:2002) |
| prEN ISO 15875-2-2002 | 冷热水塑料管道系统 交联聚乙稀（ PE - X ） 第2部分：管道 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes (ISO/FDIS 15875-2:2002) |
| prEN ISO 15875-3-2002 | 冷热水塑料管道系统 交联聚乙稀（ PE - X ） 第3部分：接头 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO/FDIS 15875-3:2002) |
| prEN ISO 15875-5-2002 | 冷热水塑料管道系统 交联聚乙稀（ PE - X ） 第5部分：系统适用性 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO/FDIS 15875-5:2002) |
| prEN ISO 15876-1-2002 | 冷热水塑料管道系统 聚丁稀（ PB ） 第1部分：总则 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General (ISO/FDIS 15876-1:2002) |
| prEN ISO 15876-2-2002 | 冷热水塑料管道系统 聚丁稀（ PB ） 第2部分：管道 | Plastics piping systems for hot and cold water installations - Polybutylen (PB) - Part 2: Pipes (ISO/FDIS 15876-2:2002) |
| prEN ISO 15876-3-2002 | 冷热水塑料管道系统 聚丁稀（ PB ） 第3部分：接头 | Plastics piping systems for hot and cold water installations - Polybutylen (PB) - Part 3: Fittings (ISO/FDIS 15876-3:2002) |
| prEN ISO 15876-5-2002 | 冷热水塑料管道系统 聚丁稀（ PB ） 第5部分：系统适用性 | Plastics piping systems for hot and cold water installations - Polybutylen (PB) - Part 5: Fittness for purpose of the system (ISO/FDIS 15876-5:2002) |
| prEN ISO 15877-1-2002 | 冷热水用塑料管道系统 氯化聚氯乙烯（PVC-C）第1部分：总则 | Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General (ISO/FDIS 15877-1:2002) |
| prEN ISO 15877-2-2002 | 冷热水用塑料管道系统 氯化聚氯乙烯（PVC-C）第2部分：管道 | Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes (ISO/FDIS 15877-2:2002) |
| prEN ISO 15877-3-2002 | 冷热水用塑料管道系统 氯化聚氯乙烯（PVC-C）第3部分：接头 | Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings (ISO/FDIS 15877-3:2002) |
| prEN ISO 15877-5-2002 | 冷热水用塑料管道系统 氯化聚氯乙烯（PVC-C）第5部分：系统用途的适合性 | Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system (ISO/FDIS 15877-5:2002) |
| prEN ISO 16101-1999 | 包装 危险货物的运输包装 塑料紧密性试验 | Packaging - Transport packaging for dangerous goods - Plastics compatibility testing (ISO/DIS 16101:1999) |
| prEN ISO 21787-2001 | 工业阀门 热塑塑料制球阀 | Industrial valves - Globe valves of thermoplastic materials (ISO/DIS 21787:2001) |
| prEN ISO 2580-2-2003 | 塑料 丙烯晴-丁二烯-苯乙烯共聚物(ABS)的模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO/FDIS 2580-2:2003) / Note: Intended as replacement for EN ISO 2580-2 (1999-05). |
| prEN ISO 2897-2-2003 | 塑料 耐冲击聚苯乙烯(PS-I)模塑和挤塑材料 第2部分：试样的制备和性能的测定 | Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO/FDIS 2897-2:2003) / Note: Intended as replacement for EN ISO 2897-2 (1999-05). |
| prEN ISO 306-2002 | 塑料 热塑性材料 维卡软化温度的测定 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO/DIS 306:2002) |
| prEN ISO 3126-2002 | 塑料管材 塑料管成分 测量与尺寸的测定 | Plastics piping systems - Plastics components - Determination of dimensions (ISO/FDIS 3126:2002) |
| prEN ISO 580-2002 | 塑料管与管道系统 注模制热塑性塑料配件 加热反应的视觉评估方法 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO/DIS 580:2002) |
| prEN ISO 6402-2-2003 | 塑料 丙烯腈-苯乙烯-丙烯酸脂(ASA)、丙烯腈-(乙烯-丙烯-二烯烃)-苯乙烯(AEPDS)和丙烯腈-(氯化聚乙烯)-苯乙 | Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determinatio |
| prEN ISO 75-1-2003 | 塑料 载荷下挠曲温度的测定 第1部分：一般试验方法 | Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO/FDIS 75-1:2003) / Note: Intended as replacement for EN ISO 75-1 (1996-02). |
| prEN ISO 75-2-2003 | 塑料 载荷下挠曲温度的测定 第2部分：塑料与硬橡胶 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics, ebonite and long-fibre-reinforced composites (ISO/FDIS 75-2:2003) / Note: Intended as replacement for EN ISO 75-2 (1996-02). |
| prEN ISO 75-3-2003 | 塑料 载荷下挠曲温度的测定 第3部分：高强度热固性叠层板和长纤维增强塑料 | Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates (ISO/FDIS 75-3:2003) / Note: Intended as replacement for EN ISO 75-3 (1996-02). |
| prEN ISO 7686-2003 | 塑料管材与管件 不透明度测定 | Plastics pipes and fittings - Determination of opacity (ISO/DIS 7686:2003) / Note: Intended as replacement for EN 578 (1993-07). |
| prEN ISO 8256-2002 | 塑料 拉伸冲击强度测定 | Plastics - Determination of tensile-impact strength (ISO/DIS 8256:2002) |
| prEN ISO 9311-1-1995 | 热塑性塑料管系统的粘合剂 第1部分： | Adhesives for thermoplastics piping systems - Part 1: Test methods for spreadability and film properties of adhesives (ISO/DIS 9311-1:1995) |
| prEN ISO 9311-3-2002 | 热塑性塑料管系统的粘合剂 第3部分：内压阻力测定的试验方法 | Adhesives for thermoplastic piping systems - Part 3: Test method for the determination of resistance to internal pressure (ISO/DIS 9311-3:2002) |
| 编号 | 中文名称 | 英文名称 |