| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| DIN 10457-1988 | 牛奶制品分析用设备.牛奶用塑料瓶抽样 | Apparatus for dairy analysis; sample bottles of plastic for milk |
| DIN 12254-1980 | 塑料实验室仪器.塞子 | Plastics laboratory ware; stoppers |
| DIN 12672-2001 | 实验室玻璃和塑料器皿.英霍夫锥形沉淀杯 | Laboratory glass or plastics ware - Imhoff sedimentation cones |
| DIN 12681-1998 | 实验室塑料器具.刻度量筒 | Plastics laboratory ware - Graduated measuring cylinders (ISO 6706:1981, modified) |
| DIN 12693-2002 | 实验室塑料器皿.可在"in"处调节的一次性微量移液管 | Plastics laboratory ware - Disposable micropipettes adjusted on "In" |
| DIN 12871-1983 | 橡胶和塑料制实验室仪器.橡胶塞 | Laboratory apparatus in rubber and plastics; elastomer stoppers |
| DIN 13014 Bb.1-1977 | 医院用聚醚型泡末塑料软垫.应用与处理说明 | Polyether foam hospital mattresses; directives for application and treatment |
| DIN 13014-1977 | 医院用聚醚型泡末塑料软垫.尺寸.要求.检验 | Polyether foam hospital mattresses; dimensions, requirements, testing |
| DIN 13145-2010 | 医疗器械.塑料锤 | Medical instruments - Mallet of plastic material |
| DIN 13148-2010 | 医疗器械.带互换塑料盘的锤 | Medical instruments - Mallet with interchangeable plastic disks |
| DIN 15560-38-1988 | 电影、电视摄影棚、舞台和摄影用放映机.第38部分:固定器装置、滤色器、彩色塑料胶片、滤色器和塑料胶片框架 | Projectors for film and television studios, stage and photographic use; holders devices, colour filters, coloured plastic films, frames for filters and plastic films |
| DIN 16780-1-1988 | 塑料模塑材料.聚合物混合料制热塑性模塑材料.分类和名称 | Plastic moulding materials; thermoplastic moulding materials of polymeric blends; classification and designation |
| DIN 16781-2-1989 | 塑料模塑材料.聚甲醛(POM)模塑材料.第2部分:试样制备及其性能测定 | Plastics moulding materials; polyoxymethylene (POM) moulding materials; preparation of specimens and determination of their properties |
| DIN 16837-2006 | 多层管.塑料多层管.一般质量要求和试验 | Multilayer pipes - Plastics-Multilayer pipes - General quality requirements and testing |
| DIN 16872-1993 | 热塑性塑料管道用管接头组件.玻璃纤维增强的聚酯树脂(UP-GE)法兰.尺寸 | Pipe joints assemblies for pipelines of thermoplastics; glass fibre reinforced polyester resin (UP-GF) flanges; dimensions |
| DIN 16887-1990 | 热塑性塑料管的试验.长期耐内压性能的测定 | Determination of the long-term hydrostatic pressure resistance of thermoplastics pipes |
| DIN 16888-1-1989 | 热塑性塑料管道化学阻抗的测定.第1部分:聚烯烃管道 | Determination of chemical resistance of thermoplastics pipes; polyolefin pipes |
| DIN 16888-2-1991 | 热塑性塑料管道化学阻抗的测定.第2部分:未增塑聚氯乙烯(PVC-U)管道 | Determination of chemical resistance of thermoplastics pipes; unplasticized polyvinyl chloride (PVC-U) pipes |
| DIN 16889-1-1989 | 热塑性塑料管道化学阻抗的测定.第1部分:聚烯烃管道 | Determination of the chemical resistance factor for thermoplastics pipes; polyolefin pipes |
| DIN 16903-1-1974 | 塑料模塑件用开口螺母镶件 | Open Insert Nuts for Plastics Mouldings |
| DIN 16903-2-1974 | 塑料模塑件用盘闭口螺母镶件 | Closed Insert Nuts with Disc for Plastics Mouldings |
| DIN 16903-3-1974 | 塑料模塑用、带有固定孔的嵌件螺母 | Closed Insert Nuts with Dead Hole for Plastics Mouldings |
| DIN 16903-4-1991 | 嵌入螺母.第4部分:塑料模制件和压铸件用重型闭式螺纹件 | Insert nuts; heavy type for plastics mouldings and pressure die castings with dead hole |
| DIN 16906-2007 | 塑料薄板和塑料薄膜的测试.样品和试样.制备和状态调节 | Testing of plastic sheeting and plastic films - Sample and specimen - Preparation and conditioning |
| DIN 16922-1981 | 用塑料制成的柔性片材.工艺分类 | Flexible sheet materials manufactured using plastics; technological classification |
| DIN 16928-1979 | 热塑性塑料管道.管接头、管道部件、管道敷设.一般说明 | Pipes of Thermoplastic Materials; Pipe Joints, Elements for Pipes, Laying; General Directions |
| DIN 16941-1986 | 热塑性塑料的挤压型材.尺寸、形状和取向的一般公差 | Thermoplastics extruded profiles; general tolerances of size, form and orientation |
| DIN 16960-1-1974 | 热塑性塑料焊接.第1部分:原则 | Welding of Thermoplastics; Principles |
| DIN 16966-8-1982 | 玻璃纤维增强聚酯管(UP-GF)管件和接头.层压塑料接头.尺寸 | Glass fibre reinforced polyester resin (UP-GF) pipe fittings and joints; Laminated joints; Dimensions |
| DIN 16980-1987 | 热塑性塑料圆棒.尺寸 | Thermoplastics rods; dimensions |
| DIN 16986-1987 | 热塑性塑料扁棒.尺寸 | Thermoplastics flat bars; dimensions |
| DIN 16995-2009 | 包装用薄膜 塑料薄膜 性能、测试 | Films for packaging - Plastic films - Properties, testing |
| DIN 18159-1-1991 | 建筑工作现场发泡塑料用泡沫塑料.绝热用现场聚氨酯泡沫塑料.应用、性能、实施、检验 | Cellular plastics as in-situ cellular plastics in building; in-situ polyurethane (PUR) foam for thermal insulation; application, properties, execution, testing |
| DIN 18159-2-1978 | 建筑中现场发泡用泡沫塑料.绝热用脲-甲醛树脂现场发泡的泡沫塑料.应用、性能、制作、检验 | Cellular Plastics as in-situ Foam in Building; In-situ Foam Produced from Urea-formaldehyde (UF) Resin for Thermal Insulation; Application, Properties, Execution, Testing |
| DIN 18204-1-2007 | 用纺织物和塑料薄膜(篷帐布)制造的建筑物和帐篷罩部件.第1部分:涂聚氯乙烯(PVC)的聚酯基底纤维 | Components for enclosures made of textile fabrics and plastic films (awnings) for structures and tents - Part 1: PVC coated polyester base fabric |
| DIN 1850-5-1998 | 关节轴承.第5部分:热固性塑料制轴套 | Plain bearings - Part 5: Thermoset plastic bushes |
| DIN 1850-6-1998 | 关节轴承.第6部分:热塑塑料制轴套 | Plain bearings - Part 6: Thermoplastic bushes |
| DIN 18541-1-2006 | 现场水泥接缝密封用热塑性塑料制造的止水带.第1部分:术语和定义、形状、尺寸、标记 | Termoplastic water stops for sealing joints in in-situ concrete - Part 1: Terms and definitions, shapes, dimensions, marking |
| DIN 18541-2-2006 | 现场水泥接缝密封用热塑性塑料制造的止水带.第2部分:要求、试验和检查材料 | Thermoplastic water stops for sealing joints in in-situ concrete - Part 2: Material requirements, testing and inspection |
| DIN 18820-1-1991 | 承载构件用玻璃纤维增强非饱和聚酯树脂和苯甲酰甲基树脂制层压塑料(GF-UP、GF-PHA).第1部分:结构、制造和特 | Laminates of textile glass-reinforced unsaturated polyester and phenacrylic resins for load-bearing structural members (GF-UP, GF-PHA); structure, manufacture and characteristics |
| DIN 18820-2-1991 | 承载构件用玻璃纤维增强式非饱和聚酯和苯酚树脂制层压塑料(GF-UP.GF-PHA).第2部分:标准层压塑料的物理参数 | Laminates of textile glass-reinforced unsaturared polyester and phenolic resins for load-bearing structural members (GF-UP, GF-PHA); physical parameters for standard laminates |
| DIN 18820-3-1991 | 承载构件用玻璃纤维增强非饱和聚酯树脂和苯甲酰甲基树脂制层压塑料(GF-UP、GF-PHA).第3部分:承载层压塑料的 | Laminates of textile glass-reinforced unsaturated polyester and phenacrylic resins for load-bearing structural members (GF-UP, GF-PHA); protective measures for load-bearing laminates |
| DIN 18820-4-1991 | 承载构件用玻璃纤维增强非饱和聚脂树酯和苯甲酰甲基树脂制层压塑料(GF-UP、GF-PHA).第4部分:试验和质量控制 | Laminates of textile glass-reinforced unsaturated polyester and phenacrylic resins for load-bearing structural members (GF-UP, GF-PHA); tests and quality control |
| DIN 1910-3-1977 | 焊接；塑料的焊接、工艺 | Welding; Welding of Plastics, Processes |
| DIN 19557-2004 | 废水处理厂.渗滤器用矿物和塑料过滤介质.要求、检验、供货和安置 | Wastewater treatment plants - Mineral filter media and plastic media for percolating filters - Requirements, testing, delivery, placing |
| DIN 21605-1990 | 采矿辅助通风设备.排气和强制通风用柔性塑料空气导管.螺旋形空气导管 | Auxiliary ventilation for mining; flexible plastic air ducts for exhaust and forced ventilation; spiral air ducts |
| DIN 21606-1988 | 矿井辅助通风设备.强制式通风设备的柔性塑料空气导管.扁平空气管 | Auxiliary ventilation in mining; flexible plastic air ducts for forced ventilation; flat air ducts |
| DIN 21610-1994 | 采矿的辅助性通风.柔性塑料通风管的要求与检验 | Auxiliary ventilation in mining - Flexible plastic airducts - Requirements and testings |
| DIN 23311-2-1998 | 矿山用护膝.第2部分:塑料护膝 | Knee pads for mining - Part 2: Plastic knee pads |
| DIN 24450-1987 | 塑料和橡胶加工用的机械.定义 | Machines for the processing of plastics and rubber; definitions |
| DIN 24531-3-2007 | 用作楼梯踏板的格板.第3部分:塑料格板 | Gratings used as stairtreads - Part 3: Plastic gratings |
| DIN 24537-3-2007 | 用作地板覆盖物的格板.第3部分:塑料格板 | Gratings used as floor coverings - Part 3: Plastic gratings |
| DIN 24900-20-2003 | 工程及相关领域图形符号.第20部分:塑料和橡胶机械 | Graphical symbols for use in the engineering and related fields - Part 20: Plastics and rubber machinery |
| DIN 24902-20-1981 | 信息用图形符号.塑料机械 | Graphical symbols for information; plastic machinery |
| DIN 29505-1987 | 航空航天.纤维增强的塑料构件.图纸和零件清单的说明 | Aerospace; components of fibre reinforced plastics; indications in drawings and parts lists |
| DIN 29583-1987 | 航空航天.飞行器的丙烯酸塑料门窗玻璃的维护和修理.一般准则 | Aerospace; maintenance and repairing of aircraft glazings of acrylic plastics; general directions |
| DIN 29640-1986 | 航空航天.丙烯酸酯塑料的软化处理.制造规程 | Aerospace; tempering of acrylic plastics; directives for manufacture |
| DIN 29972-1988 | 航空航天.硬泡沫塑料材料.薄板材 技术规范 | Aerospace; rigid cellular materials; sheet; technical specification |
| DIN 30646-2006 | 自粘胶标志(标签).塑料薄膜、铝箔和纸制铭牌的交货技术条件 | Self-adhesive signs - Technical delivery conditions for signs made of plastic film, aluminium foil and paper |
| DIN 30658-1-1998 | 地下煤气管道接头附加密封材料.第1部分:已密封煤气管道附加密封用塑料薄膜和织物衬套.安全要求和试验 | Materials for the subsequent sealing of joints in underground gas mains - Part 1: Plastic foil and textile fibre linings used to seal gaspipes already in place; safety requirements and testing |
| DIN 30677-2-1988 | 埋设管件的外部防腐处理.第2部分:加厚式热固性塑料涂层 | External corrosion protection of buried valves; heavy-duty thermoset plastics coatings |
| DIN 30823-2001 | 中等容量容器.硬质IBC.金属、硬质、塑料和复合中等容量容器.尺寸、设计和要求、标记 | Intermediate bulk containers - Rigid IBC - Metal, rigid plastics and composite intermediate bulk containers; Dimensions, design requirements, marking |
| DIN 3237-2-1994 | 主电源连接的法兰密封管座直排型阀门.第2部分:带塑料内衬 | Straight pattern valves with flange socket in main power connection - Part 2: With plastic lining |
| DIN 3268-1989 | 冲洗水箱用塑料冲洗管 | Plastic flushing tubes for flushing cisterns |
| DIN 3418-1998 | 塑料拉链.设计类型.尺寸和材料 | Plastic slide fasteners - Design types, dimensions, materials |
| DIN 34810-1999 | 六角头塑料螺钉 | Plastic hexagon head screws |
| DIN 34811-1999 | 带十字槽塑料六角头螺钉 | Plastic flat head screws with cross recess |
| DIN 34812-1999 | 带十字槽的塑料盘头螺钉 | Plastic pan head screws with cross recess |
| DIN 34813-1999 | 带十字槽的圆头塑料螺钉 | Plastic cross recessed cheese head screws |
| DIN 34814-1999 | 塑料制六角螺母 | Plastic hexagon nuts |
| DIN 34815-1999 | 普通塑料垫圈.普通系列 | Plastic plain washers - Normal series |
| DIN 34816-1999 | 塑料平垫圈.大型系列 | Plastic plain washers - Large series |
| DIN 3543-3-1978 | 塑料管用PVC排放阀.尺寸 | PVC tapping valves for plastic pipes; dimensions |
| DIN 388-1-1996 | 带波形轮缘的塑料手轮 | Hand-wheels of plastic with ripple ring |
| DIN 40734-1999 | 铅酸蓄电池.带正极栅极板的固定式通风电池.放在塑料容器中的电池.额定容量、主要尺寸和重量 | Lead acid batteries - Stationary vented cells with positive grid plates - Cells in plastic containers; rated capacities, main dimensions, weights |
| DIN 40736-1-1992 | 铅蓄电池.带有管状正极板的固定电池.塑料容器电池.额定容量、主要尺寸、重量 | Lead acid batteries; stationary cells with positive tubular plates; cells in plastic-containers; rated capacities, main dimensions, weights |
| DIN 40737-3-1999 | 铅酸蓄电池.带圆管形阳极的固定蓄电池.第3部分:放在塑料整体容器中的通风蓄电池.额定容量、主要尺寸和重量 | Lead acid batteries - Stationary batteries with positive tubular plates - Part 3: Vented batteries in plastic-monobloc-containers; rated capacities, main dimensions, weights |
| DIN 40744-1999 | 铅酸蓄电池.装在塑料整体容器内的带管形正极板的固定稳定蓄电池和固定电解质.额定容量.主要尺寸和重量 | Lead acid batteries - Stationary valve regulated batteries with positive tubular plates and immobilized electrolyte in plastic-monobloc containers - Rated capacities, main dimensions, weights |
| DIN 40763-1-1988 | 镍镉蓄电池.带纤维结构板的电池.塑料容器电池.标称容量、主要尺寸 | Nickel-cadmium-batteries; cells with fibre structured plates; cells in plastic containers; nominal capacities, main dimensions |
| DIN 40763-2-1990 | 镍镉蓄电池.带纤维结构板的电池.塑料容器电池.放电电流、最终放电电压、放电时间 | Nickel-cadmium batteries; cells with fibre structured plates; cells in plastic containers; discharge current, final discharge voltages, discharge time |
| DIN 40771-1-1981 | 镍镉蓄电池.袖珍式板电池.钢与塑料壳电池.额定容量.主要尺寸 | Nickel-cadmium-accumulators; cells with pocket-type plates, cells in steel and plastic containers; rated capacities, main dimensions |
| DIN 40771-2-1981 | 镍镉蓄电池.袖珍型板电池、钢与塑料容器电池.电气特性.放电时间 | Nickel-cadmium-accumulators; cells with pocket-type plates, cells in steel and plastic containers; electrical characteristics; discharge duration |
| DIN 40771-3-1985 | 镍镉蓄电池.盒式极板电池.安装于钢壳和塑料壳的电池.第3部分:安装方式、尺寸 | Nickel-cadmium-accumulators; cells with pocket plates; cells in steel and plastic containers; types of installation, dimensions |
| DIN 45635-37-1980 | 机器空气噪声的测量.包络面法.塑料和橡胶加工机器 | Measurement of airborne noise emitted by machines; enveloping surface method; machinery for the processing of plastic and rubber |
| DIN 46228-1-1992 | 无塑料套的管子端套 | Tubular end-sleeves without plastic sleeve |
| DIN 46228-4-1990 | 带塑料套的管头 | Tubular end-sleeves with plastic sleeve |
| DIN 46238-1985 | 塑料绝缘通信软线的弹簧电缆终端 | Springterminals for plastic insulated telecommunication cords |
| DIN 46252-1975 | 带塑料绝缘套的通信软线电缆终端 | Terminals for plastic insulated telecommunication cords |
| DIN 4724-2001 | 热水地板供热系统用塑料管道系统和辐射管道连接,中等密度的交叉链接的聚乙烯 | Plastic piping systems for warm water floor heating systems and radiator pipe connecting - Crosslinked polyethylene of medium density (PE-MDX) |
| DIN 4726-2008 | 温水表面加热设备和散热器连接设备.塑料管设备和多层管设备 | Warm water surface heating systems and radiator connecting systems - Plastics piping systems and multilayer piping systems |
| DIN 4753-4-1994 | 饮用水和服务性用水的热水器和水加热装置.第4部分:采用高温固化的硬塑料涂层材料作触水面的防腐保护.要求和 | Water heaters and water heating installations for drinking water and service water - Part 4: Corrosion protection on the water side by means of hot-setting, duroplastic coating materials; requirements and testing |
| DIN 47600-6-1974 | 最高可达 10 kV 电力电缆用金属铸造连接盒.第6部分:用0.6/1kV 塑料绝缘电缆对连接盒的连接 | Cast Metal Joint Boxes for Power Cables up to 10 kV; Correlation of Joint Boxes with Plastic Insulated Cables 0.6/1 kV |
| DIN 47600-7-1974 | 最高可达 10 kV 电力电缆用金属铸造连接盒.第7部分:1.6/1kV 塑料绝缘电缆的内部设计 | Cast Metal Joint Boxes for Power Cables up to 10 kV; Internal Design for Plastic Insulated Cables 0.6/1 kV |
| DIN 47609-1989 | 室外用塑料制电缆分配柜.要求和试验 | Cable distribution cabinets from plastic for outdoor use; requirements, tests |
| DIN 47622-1979 | 通信电缆连接套管的塑料护套管 | Plastic sleeves for telecommunication cable-connecting sleeves |
| DIN 47624-2001 | 金属导线和光纤通信电缆用塑料夹紧套管.要求和试验 | Clamping closures of plastics for telecommunication cables with metallic conductors and optical fibres - Requirements and tests |
| DIN 47634-1984 | 通讯电缆的热塑塑料套管.要求和试验 | Plastic heat shrinking sleeves, for telecommunication cables; requirements, tests |
| DIN 47645-1989 | 通信电缆的热收缩塑料盖.要求和试验 | Plastic heat shrinking caps for telecommunication cables; requirements, tests |
| DIN 4815-1-2009 | 液化石油气用橡胶和塑料软管.第1部分:软管和管道 | Rubber and plastics hoses for liquefied petroleum gas - Part 1: Hoses and tubings |
| DIN 4945-1-2005 | 抽水用带抗拉套管的出水竖管.第1部分：DN 50至 DN 200的塑料涂层钢管 | Rising pipes with tension proof socket for water raising - Part 1: Steel pipes DN 50 to DN 200, plastic coated |
| DIN 5059-1-1992 | 包装.金属和塑料管.金属管.管嘴、管肩 | Packaging; metal and plastic tubes; metal tubes; tube nozzles, tube shoulders |
| DIN 5059-2-1990 | 包装.金属和塑料管.塑料管.管嘴 | Packaging; metal and plastic tubes; plastic tubes; tube nozzles |
| DIN 5065-1987 | 包装.金属及塑料软管用端口塑料密封物 | Packaging; plastic closures for metal and plastic tubes |
| DIN 52347-1987 | 玻璃和塑料的试验.磨损试验. 用砂轮试验法和散光测量 | Testing of glass and plastics; abrasion test; method using abrasion wheels and measurement of scattered light |
| DIN 52348-1985 | 玻璃和塑料的试验.磨损试验.滴沙试验 | Testing of glass and plastics; abraison test; sand trickling method |
| DIN 53100-2007 | 金属凃层.塑料材料上镍铬的电镀涂层和铜镍铬的电镀涂层 | Metallic coatings - Electroplated coatings of nickel plus chromium and of copper plus nickel plus chromium on plastics materials |
| DIN 53122-1-2001 | 塑料和弹性薄膜、纸、纸板和其它板材试验.水蒸气渗透性测定.第1部分:重力测定法 | Testing of plastics and elastomer films, paper, board and other sheet materials - Determination of water vapour transmission - Part 1: Gravimetric method |
| DIN 53236-1983 | 着色剂的检验.测定色漆涂敷层、类似涂层和塑料色差的测量和评价条件 | Testing of colouring materials; conditions of measurement and evaluation for the determination of colour differences for paint coatings, similar coatings and plastics |
| DIN 53350-1980 | 用塑料制造的塑料薄膜和涂层的纺织织物的检验.用Ohlsen法测定弯曲刚度 | Testing of plastics films and coated textile fabrics, manufactured using plastics; determination of stiffness in bending, method according to Ohlsen |
| DIN 53357-1982 | 塑料薄板材的试验.粘接试验 | Testing of plastics sheets; adhesion test |
| DIN 53362-2003 | 带或不带涂层织物的塑料薄膜和纺织物(无纺织物除外)的试验.抗弯强度的测定.悬臂式试验法 | Testing of plastics films and textile fabrics (excluding nonwovens), coated or not coated fabrics - Determination of stiffness in bending - Method according to Cantilever |
| DIN 53363-2003 | 塑料薄膜的检验.带凹口的梯形试样的撕裂试验 | Testing of plastic films - Tear test using trapezoidal test specimen with incision |
| DIN 53366-2007 | 塑料薄膜和膜片的测试.粘连强度的测定 | Testing of plastic films and sheetings - Determination of blocking strength |
| DIN 53369-1976 | 塑料薄膜的检验.收缩应力的测定 | Testing of plastic films; determination of the shrinking stress |
| DIN 53370-2006 | 塑料薄膜的检验.用机械手触摸法测定厚度 | Testing of plastics films - Determination of the thickness by mechanical scanning |
| DIN 53377-2007 | 塑料薄膜的测试.尺寸稳定性的测定 | Testing of plastic films - Determination of dimensional stability |
| DIN 53380-1-2000 | 塑料制品试验.气体传输率的测定.第1部分:塑料薄模试验用容积测量法 | Testing of plastics - Determination of gas transmissionsrate - Part 1: Volumetrical method for testing of plastic films |
| DIN 53380-2-2006 | 塑料的试验.测定气体传输率.第2部分:塑料薄膜的压力计法 | Testing of plastics - Determination of gas transmission rate - Part 2: Manometric method for testing of plastic films |
| DIN 53380-3-1998 | 测定塑料的气体传输率.第1部分:测定塑料薄膜和塑料模压品载氧率测量法 | Testing of plastics - Determination of gas transmission rate - Part 3: Oxygen-specific carrier gas method for testing of plastic films and plastics mouldings |
| DIN 53380-4-2006 | 塑料的试验.测定气体传输率.第4部分:塑料薄膜和塑料模压品试验用二氧化碳特殊红外线吸收法 | Testing of plastics - Determination of gas transmission rate - Part 4: Carbon dioxide specific infrared absorption method for testing of plastic films and plastic mouldings |
| DIN 53381-1-1983 | 塑料的检验.聚氯乙烯(PVC)热稳定性的测定.脱氯化氢法 | Testing of plastics; determination of thermostability of polyvinyl chloride (PVC); dehydrochlorination methods |
| DIN 53383-2-1983 | 塑料的检验.用烘箱内老化检验氧化稳定性.高密度聚乙烯(PE-HD)，红外光谱测定羰基含量 | Testing of plastics; testing of oxidation stability by means of ageing in an oven; polyethylene of high density (PE-HD), infra red spectroscopic (IR) determination of the carbonyle content |
| DIN 53390-1988 | 玻璃纤维增强塑料的检验.单向玻璃纤维增强层压塑料圆棒的弯曲试验 | Testing of glass fibre reinforced plastics; bending test on unidirectional glass fibre reinforced laminated plastics in the form of round bars |
| DIN 53393-1976 | 玻璃纤维增强塑料的检验.受化学制品作用的性能 | Testing of Textile Glass-reinforced Plastics; Behaviour to the Effect of Chemicals |
| DIN 53394-1974 | 塑料的试验.在模塑状态下不饱和聚酯树脂模塑材料中单体苯乙的百分比量的测定.用Wijs溶液法测定 | Testing of plastics; determination of the percentage of styrene in unsaturated polyester resin moulding material in the moulded state, test method with Wijs-solution |
| DIN 53394-2-1993 | 塑料的检验.以不饱合聚脂树脂为基的反应模塑材料中苯乙烯百分含量的测定.气相色谱法 | Testing of plastics; determination of the percentage of styrene in reaction moulding materials based on unsaturated polyester resins; gaschromatography method |
| DIN 53399-2-1982 | 增强塑料的检验.对扁平试样的剪切试验 | Testing of reinforced plastics; shear test on plane specimens |
| DIN 53408-1967 | 塑料薄膜的检验.聚氯乙烯(PVC)在增塑剂中溶解温度的测定 | Testing of Plastics; Determination of Solubility Temperature of Polyvinyl Chloride (PVC) in Plasticizers |
| DIN 53428-1986 | 泡沫塑料暴露于液体、蒸汽和固体环境下塑料性能的测定 | Determination of the behaviour of cellular plastics when exposed to fluids, vapours and solids |
| DIN 53435-1983 | 塑料试验.对测力试件作弯曲试验和冲击试验 | Testing of plastics; bending test and impact test on dynstat test pieces |
| DIN 53442-1990 | 塑料试验.扁平试样弯曲应变区域的疲劳试验 | Flexural fatique testing of plastics using flat specimens |
| DIN 53464-1962 | 塑料的试验.热固性模压材料制模压件的收缩特性的测定 | Testing of Plastics; Determination of Shrinkage Properties of Moulded Materials from Thermosetting Moulding Materials |
| DIN 53465-1963 | 塑料检验.热固性模压塑料闭合时间的测定 | Testing of Plastics; Determination of the Closing Time of Thermosetting Compression Moulding Materials |
| DIN 53470-1951 | 模压材料的检验.制造热固模压塑料标准试样的压模 | Testing of Compression Moulding Materials; Compression Mould for the Production of Standard Specimens of Thermosetting Compression Moulding Materials |
| DIN 53474-1998 | 塑料,橡胶和弹性物的试验.氯含量的测定(维克伯法分解) | Testing of plastics, rubber and elastomers - Determination of the chlorine content (Wickbold-Combustion) |
| DIN 53477-1992 | 塑料的试验.用干筛析法测定模塑材料的颗粒大小和分布 | Testing of plastics; determination of particle size distribution of moulding materials by dry sieving analysis |
| DIN 53494-1984 | 电镀层.电镀塑料件的检验.剥离强度的测定 | Electroplated coatings; testing of electroplated plastic articles; determination of peel strenght |
| DIN 53497-1969 | 塑料的检验.在没有外部机械应力条件下.对热塑性模塑材料成形件的热贮存试验 | Testing of Plastics; Hot Storage Test on Mouldings Made of Thermoplastic Moulding Materials without External Mechanical Stressing |
| DIN 53498-1967 | 塑料的检验.热固性模压塑料的压制件热贮存 | Testing of Plastics; Heat Storage of Compression Mouldings Made of Thermosetting Compression Moulding Materials |
| DIN 53499-1974 | 塑料的检验.热固性模塑材料模压制品的煮沸试验 | Testing of plastics; boiling test of moulded articles made of thermosetting moulding materials |
| DIN 53543-1979 | 半刚性聚氨脂(PUR)完整泡沫塑料的试验.鞋底和鞋部件材料 | Testing of Semi-Rigid Polyurethane (PUR) Integral Cellular Materials; Materials for Soles and Parts of Shoes |
| DIN 53598-1-1983 | 橡胶和塑料检验用样品的随机抽样统计评价 | Statistical evaluation at off-hand samples with examples from testing of rubbers and plastics |
| DIN 53704-1988 | 塑料的试验.酚醛模塑材料中游离酚醛含量的测定.光度测定法 | Testing of plastics; determination of the free phenol in phenolic moulding materials; photometrical method |
| DIN 53715-1991 | 塑料试验.卡尔·弗歇尔滴定法测定含水量 | Testing of plastics; determination of water content by titration according to Karl Fischer |
| DIN 53728-3-1985 | 塑料的检验.稀释溶液中聚对苯二甲酸乙二醇酯(PETP)或聚丁烯二甲酸乙二醇酯(PBTP)的粘度值的测定 | Testing of plastics; determination of the viscosity number of polyethylene terephthalate (PETP) or polybutylene terephthalate (PBTP) in dilute solution |
| DIN 53733-1976 | 塑料的检验.检验用塑料制品的粉碎 | Testing of Plastics; Size Reduction of Plastic Products for Test Purposes |
| DIN 53741-1971 | 塑料的检验.用气相色谱法测定聚苯乙烯中挥发性芳烃 | Testing of Plastics; Determination of Volatile Aromatic Hydrocarbons in Polystyrene; Gas chromatographic Method |
| DIN 53742-1971 | 塑料的检验.用红外光谱法测定氯乙烯和醋酸乙烯酯共聚物中醋酸乙烯酯含量 | Testing of Plastics; Determination of the Vinyl Acetate Content of Copolymers of Vinyl Chloride and Vinyl Acetate; Infrared Spectrographic Method |
| DIN 53743-1979 | 塑料的检验.用气相色谱法测定聚氯乙烯(PVC)中的氯乙烯(VC) | Testing of plastics; gaschromatographical determination of vinyl chloride (VC) in polyvinyl chloride (PVC) |
| DIN 53746-1990 | 塑料试验.聚酰胺的验证 | Testing of plastics; proof of polyamides |
| DIN 53748-1970 | 酚醛-甲醛树脂的化学分析.酚醛塑料模塑材料和模制材料 | Chemical Analysis of Phenol-formaldehyde Resins; Phenoplastic Moulding Materials and Moulded Materials |
| DIN 53752-1980 | 塑料试验.线型热膨胀系数的测定 | Testing of plastics; determination of the coefficient of linear thermal expansion |
| DIN 53754-1977 | 塑料的试验.用砂轮法测定磨损 | Testing of plastics; determination of abrasion, abrasive disk method |
| DIN 53755-1974 | 塑料制品的检验.在受热负荷及外部机械应力作用条件下的贮存试验 | Testing of plastics articles; storage test with thermal and external mechanical stress |
| DIN 53756-1974 | 塑料制品的检验.与化学物质接触情况下的贮存试验 | Testing of plastics; storage test in contact with chemicals |
| DIN 53757-1977 | 塑料制品的检验.用长期堆垛试验测定运输和贮存包装箱的性能 | Testing of plastics articles; determination of the behaviour by stacking by long-time-test, boxes for transport and storage |
| DIN 53758-1975 | 塑料制品的试验.短时间试验内部压力对空心物体作用的测定 | Testing of plastics articles; determination of the effect of internal pressure on hollow objects by short-time test |
| DIN 53759-1975 | 塑料制品的试验.长时间试验内部压力对空心物体作用的测定 | Testing of plastics articles; determination of the effect of internal pressure on hollow objects by long-time test |
| DIN 53765-1994 | 塑料和弹性体的检验.热分析.DSC法 | Testing of plastics and elastomeres; thermal analysis; DSC-method |
| DIN 53766-1-1991 | 玻璃纤维增强塑料器具和容器的检验.粘合强度的测定 | Testing of glass fibre reinforced plastics apparatus and containers; determination of adhesive strength |
| DIN 53769-1-1988 | 玻璃纤维增强塑料管道检验.第1部分:B型管道配件纵向剪切强度的测定 | Testing of glass fibre reinforced plastics pipes; determination of the longitudinal shear strength of type B pipe fittings |
| DIN 53769-2-1986 | 玻璃纤维增加塑料管道检验.长期静液压试验 | Testing of glass fibre reinforced plastics pipes; long-term hydrostatic pressure test |
| DIN 53769-3-1988 | 玻璃纤维增强塑料管试验.管子短时间和长时间最大压力试验 | Testing of glass fibre reinforced plastics pipes; determination of initial and long-term ring stiffness |
| DIN 53769-6-1989 | 玻璃纤维增强塑料管道检验.第6部分:受内压脉动作用的管道和配件 | Testing of glass fibre reinforced plastics pipes; Testing of pipes and fittings under pulsating internal pressure |
| DIN 53771-1984 | 塑料中的着色剂的检验.着色剂抗二氧化硫的测定 | Testing of colouring materials in plastics; determination of the resistance of colouring materials to sulphur dioxide |
| DIN 53774-1-1988 | 塑料着色剂的检验.未增塑的聚氯乙烯(PVC-U)材料着色剂的检验.第2部分:基本混合物的组分和制备 | Testing of colouring materials; testing of colouring materials in unplasticized polyvinyl chloride (PVC-U) materials; composition and preparation of basic mixtures |
| DIN 53774-2-1986 | 塑料着色剂检验.无增塑聚氯乙烯模塑化合物着色剂检验.第2部分:试样制备 | Testing of colouring materials in plastics; testing of colouring materials in unplasticized polyvinyl chloride moulding compounds; preparation of specimens |
| DIN 53774-5-1986 | 塑料着色剂检验.无增塑聚氯乙烯模塑化合物着色剂检验.第5部分:连轧试验的热稳定性测定 | Testing of colouring materials in plastics; testing of colouring materials in unplasticized polyvinyl chloride moulding compounds; determination of thermal stability in the long-term milling test |
| DIN 54800-1979 | 塑料试验.试验用聚氯乙烯(PVC)糊的制备 | Testing of plastics; preparation of polyvinyl chloride (PVC) pastes for testing purposes |
| DIN 54801-1979 | 塑料试验.用Serers毛细管粘度计测定聚氯乙烯膏在高剪切率时的表观粘度 | Testing of plastics; determination of apparent viscosity at high rates of shear of polyvinyl chloride (PVC) pastes by Severs capillary viscosimeter |
| DIN 54802-1-1997 | 塑料检验.加热氯乙烯(VC)聚合物时增塑剂吸收量和吸收速度测定.第1部分:星式搅拌机法 | Testing of plastics - Determination of plasticizer sorption and rate of plasticizer sorption in the heat of vinyl chloride (VC) polymers - Part 1: Planetary mixer method |
| DIN 54802-2-1997 | 塑料式验.加热氯乙烯(VC)聚合物时增塑剂吸收量和吸收速度测定.第2部分:静态法 | Testing of plastics - Determination of plasticizer sorption and rate of plasticizer sorption in the heat of vinyl chloride (VC) polymers - Part 2: Statical method |
| DIN 54811-1984 | 塑料的检验.用毛细管流变仪测定熔融塑料物的流动性 | Testing of plastics; determining the fluidity of plastics melts by the capillary rheometer |
| DIN 54813-1994 | 塑料检验.纺织玻璃纤维增强的聚酯树脂塑料的连接试验.用弯曲剪切试验测定断裂负荷 | Testing of plastics; testing of joints of textile glass reinforced polyester resins; determination of the breaking load by the bending shear test |
| DIN 54841-3-2000 | 地下电缆和管道用塑料报警装置.第3部分:可检测的表 | Plastic warning devices for buried cables and pipelines - Part 3: Detectable table |
| DIN 54841-5-2000 | 地下电缆和管道用塑料报警装置.第5部分:电缆覆层 | Plastic warning devices for underground cables and pipelines - Part 5: Cable cover |
| DIN 55412-1-1988 | 包装.第1部分:按直线排放可装 20 瓶啤洒(0.5 升型欧洲酒瓶)的 400 mm x 300 mm 塑料制啤洒码放箱 | Packaging; 400 mm 300 mm plastic stacking crate, for 20 beer bottles (0,5 l Eurobottle), in linear arrangement |
| DIN 55412-2-1988 | 包装.第2部分:按直线排放可装 24 瓶啤洒(0.33 升型法国维希酒瓶)的 400 mm x 300 mm 塑料制啤洒码放箱 | Packaging; 400 mm 300 mm plastic stacking crate, for 24 beer bottles (0,33 l Vichytype), in linear arrangement |
| DIN 55423-1-1994 | 可堆放式能重复使用的食品运输和储存用热塑塑料.第1部分:尺寸、重量、要求 | Reusable transport and storing crates for food made of thermoplastic plastics, stackable - Part 1: Dimensions, weights, requirements |
| DIN 55423-2-1994 | 可堆放式能重复使用的食品运输和储存用热塑塑料.第2部分:性能要求和检验 | Reusable transport and storing crates for food made of thermoplastic plastics, stackable - Part 2: Performance requirements and testing |
| DIN 55427-1983 | 包装方法.塑料箱.12瓶规格 | Packaging means; plastic crates; 12 bottle size |
| DIN 55441-2-1998 | 包装试验.撞击试验.第2部分:塑料瓶的自由落体试验 | Packaging test - Impact test - Part 2: Free drop of plastic bottles |
| DIN 55445-2-1974 | 包装试验.塑料袋缝口耐久性的测定 | Packaging test; determination of endurance of seams of plasticsacks |
| DIN 55471-1-1983 | 包装用聚苯乙烯泡沫塑料.要求和检验 | Cellular polystyrene for packaging; requirements and testing |
| DIN 55471-2-1987 | 包装用聚苯乙烯泡沫塑料.模塑包装材料的造型 | Cellular polystyrene for packaging; design of moulded packaging |
| DIN 55477-1990 | 包装.非增强和增强的塑料带.要求和试验 | Packaging; non-reinforced and reinforced plastic tapes; requirements and testing |
| DIN 55481-1-1987 | 包装用聚乙烯泡沫塑料.要求、试验 | Cellular polyethylene for packaging; requirements, tests |
| DIN 55482-1-1989 | 包装用聚亚氨酯泡沫塑料.第1部分:要求、检验 | Cellular polyurethane for use in packaging; requirements and testing |
| DIN 55525-1988 | 带统一标准螺旋盖的塑料容器和玻璃容器用的优选螺纹.锯齿螺纹.尺寸 | Preferred threads, for plastic and glass containers with unified screw cap; buttress thread; dimensions |
| DIN 55526-1-1991 | 包装试验.压缩试验.标称容积10升以下的塑料容器的动态试验 | Packaging test; compression test; dynamical test for plastic containers, with a capacity up to 10 liters |
| DIN 55530-1987 | 包装用塑料薄膜.低密度聚乙烯隔挡材料 | Plastic films for packaging; barrier materials made of low density polyethylene |
| DIN 55543-2-1984 | 包装试验.塑料袋试验方法.胶接缝抗剥离性的测定 | Packaging test; test methods for plastic sacks; determination of the peel resistance of glued seams |
| DIN 55543-3-1985 | 包装检验.塑料袋试验方法.纵向接缝强度的测定 | Testing of packaging; methods of test for plastic sacks; determination of the strenght of longitudinal seams |
| DIN 55543-4-1985 | 包装检验.塑料袋试验方法.第4部分:聚乙烯薄膜皱缩的测定 | Testing of packaging; methods of test for plastic sacks; determination of the shrinkage of polyethylene films |
| DIN 55560-1-1988 | 可再封闭的防儿童打开的包装.带压力/转动系统(轴向压力作用)的塑料螺旋罩.特技系统的机械检验 | Reclosable child resistant packages; plastic screw closures with press/turn system (axial pressure effect); mechanical testing of trick system |
| DIN 55625-23-1999 | 塑料用填料.第23部分:金云母.规范和试验方法 | Extenders for plastics - Part 23: Phlogopite; specifications and methods of test |
| DIN 55625-24-1999 | 塑料用填料.第23部分:氢氧化镁.规范和试验方法 | Extenders for plastics - Part 24: Magnesium hydroxide; specifications and methods of test |
| DIN 55625-4-1999 | 塑料的填料.第4部分:白垩粉.规范和试验方法 | Extenders for plastics - Part 4: Whiting, specifications and methods of test |
| DIN 55625-5-1999 | 塑料的填料.第4部分:天然结晶的碳化钙.规范和试验方法 | Extenders for plastics - Part 5: Natural crystalline calcium carbonate (NCC), specifications and methods of test |
| DIN 55625-6-1999 | 塑料的填料.第6部分:沉降碳化钙.要求和试验方法 | Extenders for plastics - Part 6: Precipitated calcium carbonate (PCC), specifications and methods of test |
| DIN 55625-7-1999 | 塑料的填料.第7部分:白云石.要求和试验方法 | Extenders for plastics - Part 7: Dolomite, specifications and methods of test |
| DIN 6063-1-2004 | 主要用于塑料容器的螺纹.第1部分:锯齿螺纹尺寸 | Screw threads used mainly for plastic containers - Part 1: Dimensions of buttress threads |
| DIN 6063-2-2004 | 主要用于塑料容器的螺纹.第2部分:梯形螺纹.尺寸 | Threads, mainly for plastic containers - Part 2: Trapezoidal screw threads, dimensions |
| DIN 6094-5-2000 | 包装材料.瓶塞.第5部分:汽酒瓶用塑料瓶塞、软木塞和冠状软木塞 | Packaging - Finishes - Part 5: Finishes for sparkling wine bottles with plastics and cork stoppers and crown corks |
| DIN 6120-1-1996 | 可回收使用的包装盒和包装材料标志.塑料包装盒和包装材料.第1部分:图形符号 | Marking of packaging and packaging materials for recycling purposes - Plastics packaging and packaging materials - Part 1: Graphical symbols |
| DIN 6120-2-1996 | 可回收使用的包装盒和包装材料标志.塑料包装盒和包装材料.第2部分:附加标志 | Marking of packaging and packaging materials for recycling purposes - Plastics packaging and packaging materials - Part 2: Supplementary marking |
| DIN 6130-1980 | 包装方法.塑料瓶和空心体.重量和充满量的一般公差 | Means of packaging; bottles and hollow bodies made of plastics, general tolerances for weight and brimful volume |
| DIN 61853-1-1987 | 纺织玻璃纤维.增强塑料用的玻璃纤维毡片.交货技术条件 | Textile glass; textile glass mats for plastics reinforcement; technical delivery conditions |
| DIN 61853-2-1987 | 纺织玻璃纤维.增强塑料用的玻璃纤维毡片.分类和用途 | Textile glass; textile glass mats for plastics reinforcement; classification and application |
| DIN 61854-1-1987 | 玻璃纤维织物.塑料增强用的纺织玻璃纤维织物.纺织玻璃长丝织物和纺织粗纱.交货技术条件 | Textile glass; woven glass fabrics for plastics reinforcement; woven glass filament fabric and woven roving; technical delivery conditions |
| DIN 61854-2-1987 | 玻璃纤维织物.塑料增强用的纺织玻璃纤维织物.纺织玻璃长丝织物和纺织粗纱.类型 | Textile glass; woven glass fabrics for plastics reinforcement; woven glass filament fabric and woven roving; types |
| DIN 62136-1 Bb.1-2000 | 纺织机械和附件.纬编独立针织机用针和沉降片润滑油.第1部分:矿物油基润滑油的最低要求.塑料制机械零件耐针 | Textile machinery and accessories - Needle and sinker lubricating oils for weft knitting independent needle machines - Part 1: Minimum requirements of mineral oil based; examples for resistance of machine parts made from plastics against needle and sinker lubricating oils |
| DIN 62136-2 Bb.1-2004 | 纺织机械和附件.纬编独立单针刺绣机用针和沉降片润滑油.第2部分:合成油的最低要求.塑料制机械零件耐针和沉 | Textile machinery and accessories - Needle and sinker lubrication oils for weft knitting independent needle machines - Part 2: Minimum requirements of synthetic oil based - Examples for resistance of machine parts made from plastics against needle and sinker lubrication oils |
| DIN 65060-1991 | 航空航天.玻璃纤维织物.增强塑料材料用玻璃纤维丝粗纱.技术规范 | Aerospace; textile glass; textile glass filament rovings for reinforcement of plastics; technical specification |
| DIN 65067-1-1980 | 航空航天.具有纤维增强塑料覆盖层(FK)的夹层结构.技术规范 | Aerospace; sandwich structures with top layers of fibre reinforced plastics, technical specification |
| DIN 65148-1986 | 航空航天.纤维增强塑料的试验.用拉伸试验测定中层间的抗剪强度 | Aerospace; testing of fibre-reinforced plastics; determination of interlaminar shear strength by tenside test |
| DIN 65252-1999 | 航空航天系列.开孔和闭孔弹性泡沫塑料.半成品和模塑件.技术规范 | Aerospace series - Cellular elastomeric materials, open and closed cells - Semi-finished products and moulded parts; technical specification |
| DIN 65375-1989 | 航空航天.纤维增强的塑料.单向层压板的试验.与纤维方向垂直的压力试验 | Aerospace; fiber reinforced plastics; testing of unidirectional laminates; compression test transverse to fiber direction |
| DIN 65378-1989 | 航空航天.纤维增强的塑料.单向层压板的检验.与纤维方向垂直的拉伸试验 | Aerospace; fiber reinforced plastics; testing of unidirectional laminates; tensile test transverse to fiber direction |
| DIN 65382-1988 | 航空航天.塑料用加强纤维.浸渍纱线试样的拉力试验 | Aerospace; reinforcement fibres for plastics; tensile test of impregnated yarn test specimens |
| DIN 65466-1996 | 航空航天.纤维增强塑料.单向层压制品试验.拉伸剪切强度和剪切模数测定 | Aerospace - Fibre reinforced plastics - Testing of unidirectional laminates; Determination of shear strength and shear modulus in tension |
| DIN 65469-1992 | 航空航天.纤维增强的塑料.单层扁平拉伸样件的拉伸试验 | Aerospace; fibre-reinforced plastics; tensile test of monolayer flat tension specimens |
| DIN 65474-1992 | 航空航天.纤维增强的塑料.温度锋值试验方法 | Aerospace; fibre reinforced plastics; thermal-spike test method |
| DIN 65559-1991 | 航空航天.纤维增强的塑料.多向层压板的试验.缺口孔抗拉强度的测定 | Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of open-hole tensile strength |
| DIN 65560-1991 | 航空航天.纤维增强的塑料.多向层压板的试验.已填充孔抗压强度的测定 | Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of filled-hole compressive strength |
| DIN 65561-1991 | 航空航天.纤维增强的塑料.多向层压板的试验.冲击试验负荷后抗压强度的测定 | Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of compressive strength after impact test |
| DIN 65562-1991 | 航空航天.纤维增强的塑料.多向层压板的试验.支承强度的测定 | Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of bearing strength |
| DIN 65572-1992 | 航空航天.碳纤维和无活性热塑塑料制单向片材和带材的预浸料.技术规范 | Aerospace; unidirectional sheet and tape prepreg from carbon fibres and non-reactive thermoplastics; technical specification |
| DIN 65583-1999 | 航空航天.纤维增强塑料.动态负荷下纤维复合材料的玻璃化转变的测定 | Aerospace - Fibre reinforced materials - Determination of glass transition of fibre composites under dynamic load |
| DIN 65597-1993 | 航空航天.纤维增强塑料.放热反应时温差的测定 | Aerospace; fibre reinforced plastics; determination of temperature difference on exothermic reaction |
| DIN 65598-1993 | 航空航天.纤维增强塑料.层压制品裂纹频度的测定 | Aerospace; fibre reinforced plastics; determination of cracking frequency on laminates |
| DIN 65629-1993 | 航空航天.碳纤维和非活性热塑塑料制预浸渍纤维薄板材和带材. 技术规范 | Aerospace; fabric sheet and tape prepreg from carbon fibres and non-reactive thermoplastics; technical specification |
| DIN 65673-1999 | 航空航天.纤维增强塑料.纱疵,织疵和预浸渍体疵点的定义 | Aerospace - Fibre reinforced plastics - Description of yarn, fabric and prepreg defects |
| DIN 6663-1999 | 气动管系统.塑料(PVC),钢铁,和不锈钢气动管系统部件的制造工艺 | Pneumatic tube systems - Workmanship of components for pneumatic tube systems in plastics (PVC-U), ferrous steel and stainless steel |
| DIN 67530-1982 | 涂漆表面及塑料表面光泽评定用的反射计 | Reflectometer as a means for gloss assessment of plane surfaces of paint coatings and plastics |
| DIN 68872-1976 | 室内塑料椅的外层.要求.检验 | Plastic Chair Shells for Indoor Use; Requirements, Testing |
| DIN 7708-1-1980 | 塑料模塑材料.第1部分:塑料制品概念 | Plastic Moulding Materials; Plastic Products; Concepts |
| DIN 7708-4-1983 | 塑料模塑化合物种类.冷模塑用模塑化合物 | Types of plastics moulding compounds; Moulding compounds for cold moulding |
| DIN 7726-1982 | 泡沫塑料.术语定义和分类 | Cellular materials; definitions of terms and classification |
| DIN 7742-1-1988 | 塑料模塑材料.纤维素聚酯类(CA, CP, CAB)热塑性模塑材料.分类和名称 | Plastic moulding materials; cellulose ester(CA, CP, CAB) thermoplastic moulding materials; classification and designation |
| DIN 7868-1-1982 | 橡胶和塑料涂覆辊.硬度规定 | Rubber and plastics covered rollers; hardness specifications |
| DIN 7868-2-1984 | 橡胶和塑料涂覆的轧辊.表面特征 | Rubber and plastics covered rollers; surface characteristics |
| DIN 7868-3-1986 | 橡胶和塑料涂层辊子.第3部分:尺寸公差和形位公差 | Rubber and plastics covered rollers; dimensional and geometrical tolerances |
| DIN 8038-1971 | （热固性）塑料钻孔加工用镶硬质合金钻尖的直柄麻花钻 | Twist Drills with Parallel Shank with Carbide Tips for Drilling Plastics (Thermosetting Plastics) |
| DIN 8076-2008 | 热塑性材料制压力管道.聚乙烯(PE)管用金属和塑料压缩配件.通用质量要求和测试 | Pressure pipelines made from thermoplastics materials - Metal and plastics compression fittings for polyethylene (PE) pipes - General quality requirements and testing |
| DIN 9781-10-1985 | 办公机械.塑料或塑料层压材料标识卡.可靠性标志方面的要求 | Office machines; plastic or plastic laminated identification cards; requirements on authenticity marks |
| DIN CEN/TS 12200-2-2003 | 地面上使用的雨水塑料管道系统.未增塑的聚氯乙烯(PVC-U).第2部分:一致性评定指南 | Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity; German version CEN/TS 12200-2:2003 |
| DIN CEN/TS 12201-7-2003 | 给水用塑料管道系统.聚乙烯.第7部分:合格评定指南 | Plastics piping systems for water supply - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity; German version CEN/TS 12201-7:2003 |
| DIN CEN/TS 12666-2-2006 | 非压力地下排水和污水管道用塑料管道系统.聚丙烯(PE).第2部分:一致性评估指南.德文版本CEN/TS 12666-2-2005 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity; German version CEN/TS 12666-2:2005 |
| DIN CEN/TS 13130-17-2005 | 接触食料的材料和物品.可塑性物质允许极限.第17部分:塑料中碳酰氯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 17: Determination of carbonyl chloride in plastics; German version CEN/TS 13130-17:2005 |
| DIN CEN/TS 13130-20-2005 | 接触食料的材料和物品.可塑性物质允许极限.第20部分:塑料中3-氯-1,2-环氧丙烷的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 20: Determination of epichlorohydrin in plastics; German version CEN/TS 13130-20:2005 |
| DIN CEN/TS 13130-22-2005 | 接触食料的材料和物品.可塑性物质允许极限.第22部分:塑料中环氧乙烷和氧化丙烯的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 22: Determination of ethylene oxide and propylene oxide in plastics; German version CEN/TS 13130-22:2005 |
| DIN CEN/TS 13244-7-2003 | 通用、排水和污水用地下和地上压力系统用塑料管道系统.聚乙烯.第7部分:合格评定指南 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity; German version CEN/TS 13244-7:2003 |
| DIN CEN/TS 13476-4-2008 | 非受压地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)的结构壁管道系统.第4 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 4: Guidance for the assessment of conformity; German version CEN/TS 13476-4:2008 |
| DIN CEN/TS 14541-2007 | 非压力设备用塑料管道和配件.未增塑聚氯乙烯、聚丙烯和聚乙烯材料应用 | Plastics pipes and fittings for non-pressure applications - Utilisation of non-virgin PVC-U, PP and PE materials; German version CEN/TS 14541:2007 |
| DIN CEN/TS 1456-2-2003 | 直埋式和地上排水和排污用压力塑料管道系统.未增塑聚氯乙烯(PVC-U).第2部分:符合性评定指南 | Plastics piping systems for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity; German version CEN/TS 1456-2:2003 |
| DIN CEN/TS 14577-2004 | 接触食品的材料和物质.塑料.聚合添加剂.1000道尔顿以下的聚合添加剂质量系数测定的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Polymeric additives - Test method for the determination of the mass fraction of a polymeric additive that lies below 1000 Daltons; German version CEN/TS 14577:2003 |
| DIN CEN/TS 14578-2003 | 给水或排水排污用塑料管道系统.基于不饱和聚酯树脂(UP)的玻璃纤维增强热固性塑料(GRP).安装的推荐性实施规 | Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Recommended practice for installation; German version CEN/TS 14578:2003 |
| DIN CEN/TS 14758-2-2007 | 非压力地下排水和排污用塑料管道系统.含矿物调节剂的聚丙烯(PP-MD).第2部分:合格性评估指南 | Plastics piping sytems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 2: Guidance for the assessment of conformity; German version CEN/TS 14758-2:2007 |
| DIN CEN/TS 14758-3-2006 | 无压力地下排水和污水塑料管道系统.含矿物调节剂的聚丙烯(PP-MD).第3部分:安装指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3: Guidance for installation; German version CEN/TS 14758-3:2006 |
| DIN CEN/TS 14807-2005 | 塑料管道系统.基于不饱和聚酯树脂(UP)的玻璃纤维增强热固性塑料(GRP).地下GRP-UP管道的结构分析指南 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the structural analysis of buried GRP-UP pipelines; German version CEN/TS 14807:2004 |
| DIN CEN/TS 15354-2006 | 塑料.增塑聚氯乙烯(PVC-P)制成的无钢筋挤压和/或砑光薄膜和片材.特征和设计指南 | Plastics - Extruded and/or calandered, non-reinforced film and sheeting made of plasticized poly(vinyl chloride) (PVC-P) - Guidance for characterisation and designation; German version CEN/TS 15354:2006 |
| DIN CEN/TS 1555-7-2003 | 燃气输送用塑料管道系统.聚乙烯(PE).第7部分:符合性评定指南 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity; German version CEN/TS 1555-7:2003 |
| DIN CEN/TS 1852-3-2005 | 无压力地下排水和排污塑料管道系统.聚丙烯(PP).第3部分:安装指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 3: Guidance for installation; German version CEN/TS 1852-3:2003 + A1:2005 |
| DIN EN 1013-1-1998 | 单层屋顶用反光型塑料板.第1部分:一般要求和试验方法 | Light transmitting profiled plastic sheeting for single skin roofing - Part 1: General requirements and test methods; German version EN 1013-1:1997 |
| DIN EN 1013-2-1999 | 单层屋顶反光塑料型板.第2部分:玻璃纤维增强聚酯树脂板(GF-UP)特殊要求和试验方法 | Light transmitting profiled plastic sheeting for single skin roofing - Part 2: Specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP); German version EN 1013-2:1998 |
| DIN EN 1013-3-1998 | 单层屋顶用反光型塑料板.第3部分:聚氯乙烯(PVC)板的特殊要求和试验方法 | Light transmitting profiled plastic sheeting for single skin roofing - Part 3: Specific requirements and test methods for sheets of polyvinyl chloride (PVC); German version EN 1013-3:1997 |
| DIN EN 1013-4-2000 | 单层屋顶反光塑料型板.第4部分:聚碳酸酯(PC)薄板特殊要求、试验方法和性能 | Light transmitting profiled plastic sheeting for single skin roofing - Part 4: Specific requirements, test methods and performance of polycarbonate (PC) sheets; German version EN 1013-4:2000 |
| DIN EN 1013-5-2000 | 单层屋顶反光塑料型板.第5部分:聚甲基丙烯酸甲酯(PMMA)薄板特殊要求、试验方法和性能 | Light transmitting profiled plastic sheeting for single skin roofing - Part 5: Specific requirements, test methods and performance of polymethylmethacrylate (PMMA) sheets; German version EN 1013-5:2000 |
| DIN EN 1053-1995 | 塑料管道系统.非承压热塑管道系统.防水性试验方法 | Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness; German version EN 1053:1995 |
| DIN EN 1054-1995 | 塑料管道系统.建筑物排污热塑管道系统.连接件气密性试验方法 | Plastics piping systems - Thermoplastics piping systems for soil and waste discharge - Test method for airtightness of joints; German version EN 1054:1995 |
| DIN EN 1055-1996 | 塑料管道系统.建筑物排水排污热塑制管道系统.耐温度循环试验方法 | Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling; German version EN 1055:1996 |
| DIN EN 1107-2-2001 | 防水软板.尺寸稳定性测定.第2部分:屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing; German version EN 1107-2:2001 |
| DIN EN 1114-1-1997 | 橡胶机械和塑料机械.挤压机和挤压设备.第1部分:挤压机安全性要求 | Rubber and plastics machines - Extruders and extrusion lines - Part 1: Safety requirements for extruders; German version EN 1114-1:1996 |
| DIN EN 1120-1996 | 塑料管道系统.玻璃纤维增强热固性塑料(GFK)管和配件.弯曲状态下管道内壁抗化学腐蚀能力测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of a section in a deflected condition; German version EN 1120:1996 |
| DIN EN 1122-2002 | 塑料.镉含量测定.湿分解法 | Plastics - Determination of cadmium - Wet decomposition method; German version EN 1122:2001 |
| DIN EN 1186-1-2002 | 接触食品的材料和制品.塑料制品.第1部分:全迁移用条件选择和试验方法指南; 德文版本 EN 1186-1:2002 | Materials and articles in contact with foodstuffs - Plastics - Part 1: Guide to the selection of conditions and test methods for overall migration; German version EN 1186-1:2002 |
| DIN EN 1186-10-2002 | 接触食品的材料和制品.塑料制品.第10部分:向橄榄油全迁移的试验方法(橄榄油不能完全萃取时使用改良法); 德 | Materials and articles in contact with foodstuffs - Plastics - Part 10: Test methods for overall migration into olive oil (modified method for use in case where incomplete extraction of olive oil occurs); German version EN 1186-10:2002 |
| DIN EN 1186-11-2002 | 接触食品的材料和制品.塑料制品.第11部分:向C-14合成甘油三酯混合物全迁移的试验方法; 德文版本 EN 1186-11 | Materials and articles in contact with foodstuffs - Plastics - Part 11: Test methods for overall migration into mixtures of <(hoch)14>C-labelled synthetic triglycerides; German version EN 1186-11:2002 |
| DIN EN 1186-13-2002 | 接触食品的材料和物品.塑料.第13部分:高温下总迁移量试验方法 | Materials and articles in contact with foodstuffs - Plastics - Part 13: Test methods for overall migration at high temperatures; German version EN 1186-13:2002 |
| DIN EN 1186-14-2002 | 接触食品的材料和制品.塑料制品.第14部分:采用试验媒介异辛烷和95%乙醇对与油脂食品接触的塑料制品全迁移量 | Materials and articles in contact with foodstuffs - Plastics - Part 14: Test methods for 'substitute tests' for overall migration from plastics intended to come into contact with fatty foodstuffs using test media iso-octane and 95 % ethanol; German version EN 1186-14:2002 |
| DIN EN 1186-15-2002 | 接触食品的材料和制品.塑料制品.第15部分:采用快速析入异辛烷和/或95%乙醇法向油脂食品模拟物迁移的替换试 | Materials and articles in contact with foodstuffs - Plastics - Part 15: Alternative test methods to migration into fatty food simulants by rapid extraction into iso-octane and/or 95 % ethanol; German version EN 1186-15:2002 |
| DIN EN 1186-2-2002 | 接触食品的材料和制品.塑料制品.第2部分:采用全浸渍法向橄榄油全迁移的试验方法; 德文版本 EN 1186-2:2002 | Materials and articles in contact with foodstuffs - Plastics - Part 2: Test methods for overall migration into olive oil by total immersion; German version EN 1186-2:2002 |
| DIN EN 1186-3-2002 | 接触食品的材料和制品.塑料制品.第3部分:采用全浸渍法向含水模拟物全迁移的试验方法; 德文版本 EN 1186-3:2 | Materials and articles in contact with foodstuffs - Plastics - Part 3: Test methods for overall migration into aqueous simulants by total immersion; German version EN 1186-3:2002 |
| DIN EN 1186-4-2002 | 接触食品的材料和制品.塑料制品.第4部分:采用电解槽法向橄榄油全迁移的试验方法; 德文版本 EN 1186-4:2002 | Materials and articles in contact with foodstuffs - Plastics - Part 4: Test methods for overall migration into olive oil by cell; German version EN 1186-4:2002 |
| DIN EN 1186-5-2002 | 接触食品的材料和制品.塑料制品(ISO 10451:2002); German version EN ISO 10451:2002.第5部分:采用电解槽法 | Materials and articles in contact with foodstuffs - Plastics - Part 5: Test methods for overall migration into aqueous food simulants by cell; German version EN 1186-5:2002 |
| DIN EN 1186-6-2002 | 接触食品的材料和制品.塑料制品.第6部分:采用袋装法向橄榄油全迁移的试验方法; 德文版本 EN 1186-6:2002 | Materials and articles in contact with foodstuffs - Plastics - Part 6: Test methods for overall migration into olive oil using a pouch; German version EN 1186-6:2002 |
| DIN EN 1186-7-2002 | 接触食品的材料和制品.塑料制品.第7部分:采用袋装法向含水模拟物全迁移的试验方法; 德文版本 EN 1186-7:200 | Materials and articles in contact with foodstuffs - Plastics - Part 7: Test methods for overall migration into aqueous simulants using a pouch; German version EN 1186-7:2002 |
| DIN EN 1186-8-2002 | 接触食品的材料和制品.塑料制品.第8部分:采用物品充填法向橄榄油全迁移的试验方法; 德文版本 EN 1186-8:200 | Materials and articles in contact with foodstuffs - Plastics - Part 8: Test methods for overall migration into olive oil by article filling; German version EN 1186-8:2002 |
| DIN EN 1186-9-2002 | 接触食品的材料和制品.塑料制品.第9部分:采用物品充填法向橄榄油全迁移的试验方法; 德文版本 EN 1186-9:200 | Materials and articles in contact with foodstuffs - Plastics - Part 9: Test methods for overall migration into aqueous simulants by article filling; German version EN 1186-9:2002 |
| DIN EN 12012-1-2010 | 塑料和橡胶机械.粉碎机.第1部分:叶片式造粒机的安全要求.德文版本EN 12012-1-2007+A1-2008 | Plastics and rubber machines - Size reduction machines - Part 1: Safety requirements for blade granulators; German version EN 12012-1:2007+A1:2008 |
| DIN EN 12012-3-2010 | 橡胶和塑料机械.粉碎机.第3部分:碎纸机的安全性要求.德文版本EN 12012-3-2001+A1-2008 | Plastics and rubber machines - Size reduction machines - Part 3: Safety requirements for shredders; German version EN 12012-3:2001+A1:2008 |
| DIN EN 12061-1999 | 塑料管道系统.热塑管接头.耐冲击性能试验方法 | Plastics piping systems - Thermoplastics fittings - Test method for impact resistance; German version EN 12061:1999 |
| DIN EN 12095-1997 | 塑料管道系统.雨水管道系统卡圈.卡圈强度试验方法 | Plastics piping systems - Brackets for rainwater piping systems - Test method for bracket strength; German version EN 12095:1997 |
| DIN EN 12099-1997 | 塑料管道系统.聚乙烯管道材料和部件.挥发物含量测定 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content; German version EN 12099:1997 |
| DIN EN 12100-1997 | 塑料管道系统.聚乙烯(PE)阀.三点负载抗弯曲试验方法 | Plastics piping systems - Polyethylene (PE) valves - Test method for the resistance to bending between supports; German version EN 12100:1997 |
| DIN EN 12106-1997 | 塑料管道系统.聚乙烯管道.挤压后耐内压试验方法 | Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off; German version EN 12106:1997 |
| DIN EN 12117-1997 | 塑料管道系统.配件、阀门和附件.气流和压降关系的测定 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships; German version EN 12117:1997 |
| DIN EN 12118-1997 | 塑料管道系统.电量分析法测定热塑性塑料含水量 | Plastics piping systems - Determination of moisture content in thermoplastics by coulometry; German version EN 12118:1997 |
| DIN EN 12119-1997 | 塑料管道系统.聚乙烯(PE)管.耐温度循环试验方法 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling; German version EN 12119:1997 |
| DIN EN 12200-1-2001 | 地上露天用塑料雨水管道系统.未增塑聚氯乙烯.第1部分:管、管件和管道系统规范 | Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems; German version EN 12200-1:2000 |
| DIN EN 12201-1-2003 | 供水用塑料管道系统.聚乙烯.第1部分:总则 | Plastics piping systems for water supply - Polyethylene (PE) - Part 1: General; German version EN 12201-1:2003 |
| DIN EN 12201-2-2003 | 供水用塑料管道系统.聚乙烯.第2部分:管道 | Plastics piping systems for water supply - Polyethylene (PE) - Part 2: Pipes; German version EN 12201-2:2003 |
| DIN EN 12201-3-2003 | 供水用塑料管道系统.聚乙烯.第3部分:管件 | Plastics piping systems for water supply - Polyethylene (PE) - Part 3: Fittings; German version EN 12201-3:2003 |
| DIN EN 12201-4-2002 | 供水用塑料管系统.聚乙烯(PE).第4部分:阀; 德文版本 EN 12201-4:20 | Plastics piping systems for water supply - Polyethylene (PE) - Part 4: Valves; German version EN 12201-4:2001 |
| DIN EN 12201-5-2003 | 供水用塑料管道系统.聚乙烯.第5部分:系统使用的适合性 | Plastics piping systems for water supply - Polyethylene (PE) - Part 5: Fitness for purpose of the system; German version EN 12201-5:2003 |
| DIN EN 12256-1998 | 塑料管道系统.热塑管接件.已组装管接件的机械强度或柔性的测试方法 | Plastics piping systems - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings; German version EN 12256:1998 |
| DIN EN 1226-1996 | 塑料管道系统.玻璃纤维增强热固塑料(GFK)管.耐初始圆度变形验证方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection; German version EN 1226:1996 |
| DIN EN 1228-1996 | 塑料管道系统.玻璃纤维增强热固塑料(GFK)管.初始规定圆度稳定性测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness; German version EN 1228:1996 |
| DIN EN 12280-1-1998 | 橡胶或塑料涂覆织物.加速老化试验.第1部分:热老化 | Rubber- or plastic-coated fabrics - Accelerated ageing tests - Part 1: Heat ageing; German version EN 12280-1:1997 |
| DIN EN 12280-2-2002 | 橡胶和塑料涂层织物.加速老化试验.第2部分:光和风化作用的物理老化; 德文版本 EN 12280-2:2001 | Rubber- or plastic-coated fabrics - Accelerated ageing tests - Part 2: Physical ageing: Effect of light or weathering; German version EN 12280-2:2001 |
| DIN EN 12280-3-2002 | 橡胶或塑料涂层织物.加速老化试验.第3部分:环境老化; 德文版本 EN 12280-3:2002 | Rubber- or plastic-coated fabrics - Accelerated ageing tests - Part 3: Environmental ageing; German version EN 12280-3:2002 |
| DIN EN 1229-1996 | 塑料管道系统.玻璃纤维增强热固塑料(GFK)管.管壁短期内压密封性验证试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure; German version EN 1229:1996 |
| DIN EN 12293-1999 | 塑料管道系统.冷、热水用热塑性塑料管道和管件.检验已安装的组件耐温度循环的试验方法 | Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling; German version EN 12293:1999 |
| DIN EN 12294-1999 | 塑料管道系统.热水和冷水系统.真空密封性的检验方法 | Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum; German version EN 12294:1999 |
| DIN EN 12295-1999 | 塑料管道系统.热水和冷水用热塑性塑料管和相关管件.管接头耐循环压力的检测方法 | Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test methods for resistance of joints to pressure cycling; German version EN 12295:1999 |
| DIN EN 12310-2-2000 | 防水软板.抗撕裂性测定.第2部分:屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of resistance to tearing - Part 2: Plastic and rubber sheets for roof waterproofing; German version EN 12310-2:2000 |
| DIN EN 12311-2-2000 | 防水软板.拉伸性能测定.第2部分:屋顶防水用塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic and rubber sheets for roof waterproofing; German version EN 12311-2:2000 |
| DIN EN 12316-2-2001 | 防水软板.连接件抗剥离测定.第2部分:屋顶防水用塑料和橡胶板 | Flexible sheets for waterproofing - Determination of peel resistance of joints - Part 2: Plastic and rubber sheets for roof waterproofing; German version EN 12316-2:2000 |
| DIN EN 12317-2-2001 | 防水软板.连接件抗剪切测定.第2部分:屋顶防水用塑料和橡胶板 | Flexible sheets for waterproofing - Determination of shear resistance of joints - Part 2: Plastic and rubber sheets for roof waterproofing; German version EN 12317-2:2000 |
| DIN EN 12332-1-1998 | 橡胶或塑料涂层的纺织物.破裂强度的测定.第1部分:钢球法 | Rubber or plastic coated fabrics - Determination of bursting strength - Part 1: Steel ball method; German version EN 12332-1:1998 |
| DIN EN 12332-2-2003 | 橡胶或塑料涂层织物.破裂强度测定.第2部分:液压法 | Rubber- or plastic-coated fabrics - Determination of bursting strength - Part 2: Hydraulic method; German version EN 12332-2:2002 |
| DIN EN 12409-2009 | 橡胶和塑料机械.热成形机械.安全要求 | Plastics and rubber machines - Thermoforming machines - Safety requirements; English version of DIN EN 12409:2009-01 |
| DIN EN 1254-3-1998 | 铜和铜合金.管配件.第3部分:与塑料管一起用的带压紧连接端部的管配件 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes; German version EN 1254-3:1998 |
| DIN EN 12573-2-2000 | 焊接固定无压力热塑性塑料槽罐.第2部分:立式圆柱形槽罐的计算 | Welded static non-pressurised thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanks; German version EN 12573-2:2000 |
| DIN EN 12575-1998 | 塑料.热固成形模塑化合物.SMC中纤维湿润级的测定 | Plastics - Thermoset moulding compounds - Determination of the degree of fibre wet out in SMC; German version EN 12575:1998 |
| DIN EN 12576-1998 | 塑料.纤维增强的复合材料.SMC,BMC和DMC制模压试验板件的备制 | Plastics - Fibre reinforced composites - Preparation of compression moulded test plates of SMC, BMC and DMC; German version EN 12576:1998 |
| DIN EN 12666-1-2006 | 无压地下排水和排污塑料管道系统.聚丙烯(PP).第1部分:管道、配件和系统规范.德文版本EN 12666-1-2005 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system; English version of DIN EN 12666-1:2006-03 |
| DIN EN 12691-2006 | 防水软板.屋顶防水用沥青、塑料和橡胶薄板.耐冲击性测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to impact English version of DIN EN 12691:2006-06 |
| DIN EN 12709-2000 | 塑料桶. 标称容积为20升至120升的非活动桶盖(封闭盖)的圆桶 | Plastic drums - Non-removable head (tight head) circular cross section drums with a nominal capacity of 20 l to 120 l; German version EN 12709:2000 |
| DIN EN 12712-2000 | 塑料液体容器.托板为800mm1200mm,1000mm1200mm和1140mm1140mm优化利用的标称容量为20升至60升的塑 | Plastic jerricans - Jerricans with a nominal capacity of 20 l to 60 l for optimal utilisation of pallets 800 mm × 1200 mm, 1000 mm × 1200 mm und 1140 mm × 1140 mm; German version EN 12712:2000 |
| DIN EN 12713-2000 | 标称容积为20升至60升的塑料容器用带有螺纹的盖子密封系统 | Screw cap closure systems for plastics containers with a nominal capacity of 20 l to 60 l; German version EN 12713:2000 |
| DIN EN 12730-2001 | 防水软板.屋顶防水用沥青、塑料和橡胶薄板.耐静载荷测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to static loading; German version EN 12730:2001 |
| DIN EN 12759-2001 | 橡胶或塑料涂层织物.耐液体性能测定 | Rubber- or plastic-coated fabrics - Determination of resistance to liquids; German version EN 12759:2001 |
| DIN EN 1277-2004 | 塑料管道系统.用于地下无压装置的热塑性管道系统.橡胶密封环连接件密封性的检验方法 | Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints; German version EN 1277:2003 |
| DIN EN 12814-1-1999 | 热塑性塑料半成品焊接接头的试验.第1部分:弯曲试验 | Testing of welded joints of thermoplastics semi-finished products - Part 1: Bend test; German version EN 12814-1:1999 |
| DIN EN 12814-2-2000 | 热塑性塑料半成品的焊接接头试验.第2部分:拉伸试验.德文版本EN 12814-2:2000 | Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test; German version EN 12814-2:2000 |
| DIN EN 12814-5-2000 | 热塑性塑料半成品的焊接接头试验.第5部分:宏观检查 | Testing of welded joints of thermoplastics semi-finished products - Part 5: Macroscopic examination; German version EN 12814-5:2000 |
| DIN EN 12814-6-2000 | 热塑性塑料半成品的焊接接头试验.第6部分:低温拉伸试验 | Testing of welded joints of thermoplastics semi-finished products - Part 6: Low temperature tensile test; German version EN 12814-6:2000 |
| DIN EN 12877-1-2000 | 塑料中的着色剂.塑料中着色剂的处理过程中颜色热稳定性的测定.第1部分:概述 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 1: General introduction; German version EN 12877-1:1999 |
| DIN EN 12877-2-2000 | 塑料中的着色剂.塑料中着色剂的处理过程中颜色热稳定性的测定.第2部分:用注塑模塑法测定 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 2: Determination by injection moulding; German version EN 12877-2:1999 |
| DIN EN 12877-3-2000 | 塑料中的着色剂.塑料中着色剂的处理过程中颜色热稳定性的测定.第3部分:烘箱试验法测定 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 3: Determination by oven test; German version EN 12877-3:1999 |
| DIN EN 12877-4-2000 | 塑料中的着色剂.塑料中着色剂的处理过程中颜色热稳定性的测定.第4部分:双辊研磨法测定 | Colouring materials in plastics - Determination of colour stability to heat during processing of colouring materials in plastics - Part 4: Determination by two-roll milling; German version EN 12877-4:1999 |
| DIN EN 12943-1999 | 热塑性塑料用填充材料.范围、名称与符号、要求和试验 | Filler materials for thermoplastics - Scope, designation, requirements, tests; German version EN 12943:1999 |
| DIN EN 1296-2001 | 防水软板.屋顶防水用沥青、塑料和橡胶薄板.长期高温暴露人工老化方法 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterprofing - Method for artificial ageing by long term exposure to elevated temperature; German version EN 1296:2000 |
| DIN EN 1297-2004 | 防水用软薄板.屋顶防水用沥青、塑料和橡胶薄板.长期暴露于紫外线辐射、高温和水的组合条件下的人工老化法 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Method of artificial ageing by long term exposure to the combination of UV radiation, elevated temperature and water; German version EN 1297:2004 |
| DIN EN 130100-1998 | 分规范.直流电用固定式聚乙烯 － 对笨二酸盐塑料薄膜介质金属箔电容器 | Sectional specification: Fixed polyethylene-terephthalate film dielectric metal foil capacitors for direct current; German version EN 130100:1997 |
| DIN EN 13067-2003 | 塑料焊接人员.焊工的合格测试.热塑性塑料焊接组件 | Plastics welding personnel - Approval testing of welders - Thermoplastics welded assemblies; German version EN 13067:2003 |
| DIN EN 13100-1-2000 | 热塑性塑料半成品焊接接头的无损检验.第1部分:外观检验 | Non destructive testing of welded joints of thermoplastics semi-finished products - Part 1: Visual examination; German version EN 13100-1:1999 |
| DIN EN 13117-1-2000 | 运输包装.可重复使用硬塑料配送箱.第1部分:通用配送箱 | Transport packaging - Reusable, rigid plastics distribution boxes - Part 1: General purpose application; German version EN 13117-1:2000 |
| DIN EN 13117-2-2000 | 运输包装.可重复使用的硬塑料配送箱.第2部分:试验的通用规范 | Transport packaging - Reusable, rigid plastics distribution boxes - Part 2: General specifications for testing; German version EN 13117-2:2000 |
| DIN EN 13121-4 Berichtigung 1-2007 | 地上用玻璃纤维增强塑料(GRP)储罐和容器.第4部分:交付、安装和维修.DIN EN 13121-4-2005技术勘误 | GRP tanks and vessels for use above ground - Part 4: Delivery, installation and maintenance; German version EN 13121-4:2005, Corrigenda to DIN EN 13121-4:2005-03; German version EN 13121-4:2005/AC:2007 |
| DIN EN 13130-1-2004 | 接触食品的材料和物品.受限制的塑料物质.第1部分:从塑料到食品和食品模拟物的特定迁移的试验方法指南以及塑 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 1: Guide to test methods for the specific migration of substances from plastics to foods and food simulants and the determination of substances in plastics and the selection of conditions of exposure to food simulants; German version EN 13130-1:2004 |
| DIN EN 13130-2-2004 | 接触食品的材料和物品.受限制的塑料物质.第2部分:食品模拟物中对苯二酸含量的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 2: Determination of terephthalic acid in food simulants; German version EN 13130-2:2004 |
| DIN EN 13130-3-2004 | 接触食品的材料和物品.受限制的塑料物质.第3部分:食品和食品模拟物中丙烯腈含量的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 3: Determination of acrylonitrile in food and food simulants; German version EN 13130-3:2004 |
| DIN EN 13130-4-2004 | 接触食品的材料和物品.受限制的塑料物质.第4部分:塑料中1、3-丁二烯含量的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 4: Determination of 1,3-butadiene in plastics; German version EN 13130-4:2004 |
| DIN EN 13130-5-2004 | 接触食品的材料和物品.受限制的塑料物质.第5部分:食品模拟物中1、1-二氯乙烯含量的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 5: Determination of vinylidene chloride in food simulants; German version EN 13130-5:2004 |
| DIN EN 13130-6-2004 | 接触食品的材料和物品.受限制的塑料物质.第6部分:塑料中1、1-二氯乙烯含量的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 6: Determination of vinylidene chloride in plastics; German version EN 13130-6:2004 |
| DIN EN 13130-7-2004 | 接触食品的材料和物品.受限制的塑料物质.第7部分:食品模拟物中单乙二醇和二甘醇含量的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 7: Determination of monoethylene glycol and diethylene glycol in food simulants; German version EN 13130-7:2004 |
| DIN EN 13130-8-2004 | 接触食品的材料和物品.受限制的塑料物质.第8部分:塑料中异氰酸酯含量的测定 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Part 8: Determination of isocyanates in plastics; German version EN 13130-8:2004 |
| DIN EN 13164-2009 | 建筑物用绝热产品.工厂制聚苯乙烯泡沫塑料(XPS)产品.规范 | Thermal insulation products for buildings - Factory made products of extruded polystyrene foam (XPS) - Specification; English version of DIN EN 13164:2009-02 |
| DIN EN 13244-1-2003 | 地下和地上通用压力排水系统的塑料管道系统.聚乙烯(PE).第1部分:总则 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General; German version EN 13244-1:2002 |
| DIN EN 13244-2-2003 | 地下和地上通用压力排水系统的塑料管道系统.聚乙烯(PE).第2部分:管道 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes; German version EN 13244-2:2002 |
| DIN EN 13244-3-2003 | 地下和地上通用压力排水排污系统的塑料管道系统.聚乙烯(PE).第3部分:配件 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings; German version EN 13244-3:2002 |
| DIN EN 13244-4-2003 | 地下和地上通用压力排水系统的塑料管道系统.聚乙烯(PE).第4部分:阀门 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 4: Valves; German version EN 13244-4:2002 |
| DIN EN 13244-5-2003 | 地下和地上通用压力排水系统的塑料管道系统.聚乙烯(PE).第5部分:系统适用性 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system; German version EN 13244-5:2002 |
| DIN EN 13245-1-2004 | 塑料.建筑物用未增塑聚氯乙烯型材.第1部分:浅色型材的名称与符号 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1: Designation of light coloured profiles; German version EN 13245-1:2004 |
| DIN EN 13245-2-2008 | 塑料.建筑物用未增塑聚氯乙烯(PVC-U)型材.第2部分:内部和外部墙及天花板精整用PVC-U型材和PVC-UE型材 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 2: PVC-U profiles and PVC-UE profiles for internal and external wall and ceiling finishes; English version of DIN EN 13245-2:2008-12 |
| DIN EN 1329-1-1999 | 建筑物污物和污水排放(低温和高温)用塑料管道系统.未增塑聚氯乙烯(PVC-U).第1部分:管道、配件和系统规范; | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system; German version EN 1329-1:1999 |
| DIN EN 13329-2009 | 叠层地板覆盖物.氨基塑料热固树胶基表层元件.规范、要求和试验方法 | Laminate floor coverings - Elements with a surface layer based on aminoplastic thermosetting resins - Specifications, requirements and test methods ; German version EN 13329:2006+A1:2008 |
| DIN EN 13416-2001 | 防水软板.屋顶防水沥青、塑料和橡胶板.取样规则. | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Rules for sampling; German version EN 13416:2001 |
| DIN EN 13421-2006 | 塑料.热模化合物.复合和增强纤维.压模化合物的向异性能测定用试样制备 | Plastics - Thermoset moulding compounds - Composites and reinforcement fibres - Preparation of specimens for determining the anisotropy of the properties of compression moulding composites English version of DIN EN 13421:2006-05 |
| DIN EN 13476-1-2007 | 无压地下排水和污水用塑料管系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)的结构壁管系统.第1部分: | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characteristics; English version of DIN EN 13476-1:2007-08 |
| DIN EN 13476-2-2007 | 无压地下排水和污水用塑料管系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管系统.第2部分:A型 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A; English version of DIN EN 13476-2:2007-08 |
| DIN EN 13476-3-2009 | 无压地下排水和污水塑料管系统 未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)结构壁管系统 第3部分:B型 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B (includes Amendment A1:2009) ; English version of DIN EN 13476-3:2009-04 |
| DIN EN 13483-2005 | 可测量的燃料分配系统用带内部蒸气回收的橡胶和塑料软管和软管组件.规范 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification; German version EN 13483:2005 |
| DIN EN 13566-1-2003 | 地下非承压排水排污网翻新用塑料管道系统.第1部分:总则 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General; German version EN 13566-1:2002 |
| DIN EN 13566-2-2006 | 地下非压力排水排污网翻新用塑料管道系统.第2部分:连续管加衬.德文版本 EN 13566-2-2005 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes; English version of DIN EN 13566-2:2006-02 |
| DIN EN 13566-3-2003 | 地下非承压排水排污网翻新用塑料管道系统.第3部分:紧配合管加衬 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes; German version EN 13566-3:2002 |
| DIN EN 13566-4-2003 | 地下非压力排水排污网翻新用塑料管道系统.第4部分:硫化管加衬 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes; German version EN 13566-4:2002 |
| DIN EN 13566-7-2007 | 地下非压力排水和排污网的修缮用塑料管道系统.第7部分:螺旋缠绕管内衬 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes English version of DIN EN 13566-7:2007-06 |
| DIN EN 13583-2001 | 防水软板,屋顶防水沥青、塑料和橡胶片.冰雹耐受性测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of hail resistance; German version EN 13583:2001 |
| DIN EN 13592-2008 | 家用废弃物收集用塑料袋.类型、要求和试验方法 | Plastics sacks for household waste collection - Types, requirements and test methods (includes Corrigendum Amendment A1:2007+Corrigendum AC:2008); English version of DIN EN 13592:2008-09 |
| DIN EN 13598-1-2003 | 无压力地下排水和排污用塑料管道系统.非增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE).第1部分:包括浅层检 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers; German version EN 13598-1:2003 |
| DIN EN 13598-2-2009 | 无压力地下排水和排污用塑料管道系统 非增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE) 第2部分:交通范围 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers in traffic areas and deep underground installations; English version of DIN EN 13598-2:2009-04 |
| DIN EN 1360-2005 | 已测燃料分配系统用橡胶和塑料软管及软管组件.规范 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification; German version EN 1360:2005 |
| DIN EN 13655-2003 | 塑料.农业和园艺用热塑性塑料薄膜覆盖物 | Plastics - Mulching thermoplastic films for use in agriculture and horticulture; German version EN 13655:2002 |
| DIN EN 13689-2003 | 翻新塑料管道系统分类和设计指南 | Guidance on the classification and design of plastics piping systems used for renovation; German version EN 13689:2002 |
| DIN EN 13706-1-2003 | 增强塑料复合材料.挤拉制型材规范.第1部分:命名 | Reinforced plastic composites - Specification for pultruded profiles - Part 1: Designation; German version EN 13706-1:2002 |
| DIN EN 13706-2-2003 | 增强塑料复合材料.挤拉制型材规范.第2部分:试验方法和一般要求 | Reinforced plastic composites - Specifications for pultruded profiles - Part 2: Methods of test and general requirements; German version EN 13706-2:2002 |
| DIN EN 13706-3-2003 | 增强塑料复合材料.挤拉制型材规范.第3部分:特殊要求 | Reinforced plastic composites - Specifications for pultruded profiles - Part 3: Specific requirements; German version EN 13706-3:2002 |
| DIN EN 13765-2003 | 烃类、溶剂和化学品输送用热塑性多层(非硫化)塑料软管和软管组件.规范 | Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification; German version EN 13765:2003 |
| DIN EN 13887-2003 | 结构胶粘剂.粘结结合前金属和塑料的表面准备指南 | Structural adhesives - Guidelines for surface preparation of metals and plastics prior to adhesive bonding; German version prEN 13887:2003 |
| DIN EN 13897-2005 | 防水用柔性薄板.屋顶防水用沥青、塑料和橡胶薄板.低温拉伸后防水性的测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of watertightness after stretching at low temperature; German version EN 13897:2004 |
| DIN EN 13900-1-2003 | 颜料和填料.扩散方法和在塑料中可扩散性的评估.第1部分:概述 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 1: General introduction; German version EN 13900-1:2003 |
| DIN EN 13900-2-2003 | 颜料和填料.扩散方法和在塑料中可扩散性的评估.第2部分:用两辊研磨测定色彩特点和在增塑聚氯乙烯中的易扩散 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 2: Determination of colouristic properties and ease of dispersion in plasticized polyvinylchloride by two-roll milling; German version EN 13900-2:2003 |
| DIN EN 13900-3-2003 | 颜料和填充剂.扩散方法和在塑料中可扩散性的评估.第3部分:用两辊研磨测定色彩特点和黑色及彩色颜料在聚乙烯 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 3: Determination of colouristic properties and ease of dispersion of black and colour pigments in polyethylene by two-roll milling; German version EN 13900-3:2003 |
| DIN EN 13900-4-2004 | 颜料和稀释剂.扩散方法和在塑料中可扩散性的评估.第4部分:由双滚研磨机测定聚乙烯中的白颜料的颜色性能和易 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 4: Determination of colouristic properties and ease of dispersion of white pigments in polyethylene by two-roll milling; German version EN 13900-4:2004 |
| DIN EN 13900-5-2005 | 颜料和稀释剂.扩散方法和在塑料中可扩散性的评定.第5部分:通过过滤器压力值试验测定 | Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 5: Determination by filter pressure value test; German version EN 13900-5:2005 |
| DIN EN 1393-1996 | 塑料管道系统.玻璃纤维增强热固性塑料管(GFK).初始纵向拉伸性能测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes; Determination of initial longitudinal tensile properties; German version EN 1393:1996 |
| DIN EN 1394-1996 | 塑料管道系统.玻璃纤维增强热固塑料管(GFK).切线方向表面管头拉伸性能测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength; German version EN 1394:1996 |
| DIN EN 13948-2008 | 防水柔性薄板材.屋顶防水用沥青、塑料和橡胶薄板材.根部防渗透性测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to root penetration; English version of DIN EN 13948:2008-01 |
| DIN EN 13956-2007 | 防水用柔性薄板.屋顶防水用塑料和橡胶薄板.定义和特征 | Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Definitions and characteristics English version of DIN EN 13956:2007-04 |
| DIN EN 13967-2007 | 防水弹性薄板.包含塑料和橡胶底层制箱用塑料和橡胶防潮薄板.定义和特性(包括修改件A1-2006).英文版本EN 139 | Flexible sheets for waterproofing - Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet - Definitions and characteristics; German version EN 13967:2004 + A1:2006 |
| DIN EN 13972-2003 | 刚性塑料容器.标称容量、充满容量与总容量的定义和充满容量与总容量的测量; 德文版本 EN 13972:2002 | Rigid plastics containers - Definition of nominal, brimful and total capacity and measurement of brimful and total capacity; German version EN 13972:2002 |
| DIN EN 13973-2003 | 刚性塑料容器.排水能力的测定方法; 德文版本 EN 13973:2002 | Rigid plastics containers - Method for determination of drainability; German version EN 13973:2002 |
| DIN EN 13974-2003 | 刚性塑料容器.尺寸、重量和容积公差规范; 德文版本 EN 13974:2002 | Rigid plastics containers - Specification of tolerance for dimensions, weight and volume; German version EN 13974:2002 |
| DIN EN 13984-2005 | 防水用柔性薄板.塑料和橡胶蒸气控制层.定义和特性 | Flexible sheets for waterproofing - Plastic and rubber vapour control layers - Definitions and characteristics; German version EN 13984:2004 |
| DIN EN 13984/A1-2007 | 防水用柔性薄板.塑料和橡胶蒸汽控制层.定义和特性 | Flexible sheets for waterproofing - Plastic and rubber vapour control layers - Definitions and characteristics; German version EN 13984:2004/A1:2006 |
| DIN EN 1411-1996 | 塑料管和管道系统.热塑塑料管.梯级法测定抗外冲击应力能力 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of resistance to external blows by the staircase method; German version EN 1411:1996 |
| DIN EN 14233-2003 | 接触食品的材料和物品.塑料.,测定微波炉或普通炉加热过程中和食品接触时塑料和物品的温度以选择适当的置换 | Materials and articles in contact with foodstuffs - Plastics - Determination of temperature of plastics materials and articles at the plastics/food interface during microwave and conventional oven heating in order to select the appropriate temperature for migration testing; German version EN 14233:2002 |
| DIN EN 14364-2009 | 压力和无压力排水和排污塑料管道系统.基于不饱和聚酯树脂(UP)的玻璃增强热固性塑料(GRP).管件、配件和连接 | Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints (includes Amendment A1:2008); English version of DIN EN 14364:2009-02 |
| DIN EN 1437-2002 | 塑料管道系统.地下排水排污用管道系统.抗混合温度循环和外加负荷的试验方法; 德文版本 EN 1437:2002 | Plastics piping systems - Piping systems for underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading; German version EN 1437:2002 |
| DIN EN 14401-2004 | 硬质塑料容器.闭塞物有效性的试验方法 | Rigid plastics containers - Methods to test the effectiveness of closures; German version EN 14401:2004 |
| DIN EN 14408-1-2004 | 地下气体供给网络的翻修用塑料管道系统.第1部分:总则 | Plastics piping systems for renovation of underground gas supply networks - Part 1: General; German version EN 14408-1:2004 |
| DIN EN 14408-3-2004 | 地下气体供给网络的翻修用塑料管道设备.第3部分:紧配合管道衬 | Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes; German version EN 14408-3:2004 |
| DIN EN 14409-1-2004 | 地下水供给网络的翻新用塑料管道设备.第1部分:总则 | Plastics piping systems for renovation of underground water supply networks - Part 1: General; German version EN 14409-1:2004 |
| DIN EN 14409-3-2004 | 地下水供给网络的翻新用塑料管道设备.第3部分:紧配合管道衬 | Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close-fit pipes; German version EN 14409-3:2004 |
| DIN EN 14447-2005 | 纤维增强塑料.玻璃垫增强热塑性塑料.流动性和固化的测定 | Fibre reinforced plastics - Glass mat reinforced thermoplastics (GMT) - Determination of flowability and solidification; German version of EN 14447:2005 |
| DIN EN 14471-2005 | 烟囱.带塑料烟道衬的系统烟囱.要求和试验方法 | Chimneys - System chimneys with plastic flue liners - Requirements and test methods; English version of DIN EN 14471 |
| DIN EN 14481-2003 | 与食品接触的材料和物品.塑料.测定脂肪催化剂的试验方法 | Materials and articles in contact with foodstuffs - Plastics - Test methods for the determination of fatty contact; German version EN 14481:2003 |
| DIN EN 1451-1-1999 | 建筑物结构体中的废水和污物排放系统用塑料管道系统(低温和高温).聚丙烯(PP).第1部分:管、管接头和管道系统 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system; German version EN 1451-1:1998 |
| DIN EN 14521-2004 | 弹性地板覆盖物.带有装饰层的有或无泡沫塑料背衬的光滑橡胶地板覆盖物的规范 | Resilient floor coverings - Specification for smooth rubber floor coverings with or without foam backing with a decorative layer; German version EN 14521:2004 |
| DIN EN 1453-1-2000 | 建筑物内污物和废物排出(高温和低温)用承重墙管的塑料管道系统. 硬氯乙烯管(PVC-U).第1部分:管道和系统规范 | Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system; German version EN 1453-1:2000 |
| DIN EN 1455-1-1999 | 建筑结构中污物和废水排放(低温和高温)用塑料管道系统.丙烯腈-丁二烯-苯乙烯共聚物.第1部分:管道、管件和系 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Specification for pipes, fittings and the system; German version EN 1455-1:1999 |
| DIN EN 14598-1-2005 | 增强热固性模塑复合物.模压塑料板材(SMC)和模塑料块(BMC)的规范.第1部分:名称与符号 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation; German version EN 14598-1:2005 |
| DIN EN 14598-2-2005 | 增强热固性模塑复合物.模压塑料板材(SMC)和模塑料块(BMC)的规范.第2部分:试验方法和一般要求 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements; German version EN 14598-2:2005 |
| DIN EN 14598-3-2005 | 增强热固性模塑复合物.模压塑料板材(SMC)和模塑料块(BMC)的规范.第3部分:特殊要求 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements; German version EN 14598-3:2005 |
| DIN EN 14802-2006 | 塑料管道系统.监测室和人孔用热塑性竖井.测定耐路表面和交通载荷能力.德文版本EN 14802-2005 | Plastics piping systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading; English version of DIN EN 14802:2006-03 |
| DIN EN 14867-2005 | 包装.塑料冰冻袋.规范和试验方法 | Packaging - Plastic freezer bags - Specifications and test methods; German version EN 14867:2005 |
| DIN EN 14882-2005 | 橡胶或塑料覆层织物.摩擦的静态和动态系数的测定 | Rubber or plastic coated fabrics - Determination of the static and dynamic coefficient of friction; English version of DIN EN 14882:2005 |
| DIN EN 14886-2008 | 塑料和橡胶机械.块状泡沫塑料用带刀切削机.安全要求 | Plastics and rubber machines - Bandknife cutting machines for block foams - Safety requirements; English version of DIN EN 14886:2008-06 |
| DIN EN 14909-2006 | 防水弹性薄板.塑料和橡胶防水进程.定义和特征 | Flexible sheets for waterproofing - Plastic and rubber damp proof courses - Definitions and characteristics; German version EN 14909:2006 |
| DIN EN 14932-2007 | 塑料.包装带用伸缩性热塑薄膜.要求和试验方法 | Plastics - Stretch thermoplastic films for wrapping bales - Requirements and test methods; English version of DIN EN 14932:2007-03 |
| DIN EN 14963 Berichtigung 1-2007 | 屋顶覆盖物.带和不带竖立塑料构件的连续天窗.分类、要求和试验方法.DIN EN 14963-2006技术勘误 | Roof coverings - Continuous rooflights of plastics with or without upstands - Classification, requirements and test methods; German version EN 14963:2006, Corrigenda to DIN EN 14963:2006-12 |
| DIN EN 14963-2006 | 屋顶遮盖物.带或不带竖立构件的塑料采光屋顶窗.分类要求和试验方法 | Roof coverings - Continuous rooflights of plastics with or without upstands - Classification, requirements and test methods; English version of DIN EN 14963:2006-12 |
| DIN EN 14979-2006 | 包装.软塑料/金属层压管.S13喷嘴的尺寸和公差 | Packaging - Flexible plastic/metal laminate tubes - Dimensions and tolerances of nozzle S 13 English version of DIN EN 14979:2006-05 |
| DIN EN 14987-2007 | 塑料.评估废水处理场生物降解能力.最终验收和规范 | Plastics - Evaluation of disposability in waste water treatment plants - Test scheme for final acceptance and specifications; English version of DIN EN 14987:2007-02 |
| DIN EN 14995-2007 | 塑料.评定降解塑料可堆肥性.试验方案和规范 | Plastics - Evaluation of compostability - Test scheme and specifications; English version of DIN EN 14995:2007-03 |
| DIN EN 15012-2008 | 塑料管系统.建筑结构内污物和废弃物排放系统.管道、配件及其连接件用性能特点 | Plastics piping systems - Soil and waste discharge systems within the building structure - Performance characteristics for pipes, fittings and their joints; English version of DIN EN 15012:2008-02 |
| DIN EN 15014-2008 | 塑料管系统.压力下水和其他液体用地下埋设和地上铺设系统.管道、配件及其连接件用性能特点 | Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints; English version of DIN EN 15014:2008-01 |
| DIN EN 15015-2008 | 塑料管系统.非人类消耗用冷热水系统.管、配件及其连接件用性能特点 | Plastics piping systems - Systems for hot and cold water not intended for human consumption - Performance characteristics for pipes, fittings and their joints; English version of DIN EN 15015:2008-01 |
| DIN EN 15067-2008 | 塑料和橡胶设备.袋子用薄膜加工机.安全要求 | Plastics and rubber machines - Film converting machines for bags and sacks - Safety requirements; English version of DIN EN 15067:2008-03 |
| DIN EN 1519-1-2000 | 建筑结构中排污(低温和高温)用塑料管道系统.聚乙烯(PE).第1部分:管、管件和系统的规范 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system; German version EN 1519-1:1999 |
| DIN EN 15284-2007 | 与食品接触的材料和制品.陶瓷、玻璃、玻璃陶瓷或塑料炊具的微波加热耐力用试验方法 | Materials and articles in contact with food stuffs - Test method for the resistance to microwave heating of ceramic, glass, glass-ceramic or plastic cookware; Germang version EN 15284:2007 |
| DIN EN 15342-2008 | 塑料.再生塑料.聚苯乙烯(PS)再生物的特性 | Plastics - Recycled Plastics - Characterization of polystyrene (PS) recyclates; English version of DIN EN 15342:2008-02 |
| DIN EN 15343-2008 | 塑料.再生塑料.塑料再生可追溯性和一致性与再造内容的评估 | Plastics - Recycled Plastics - Plastics recycling traceability and assessment of conformity and recycled content; English version of DIN EN 15343:2008-02 |
| DIN EN 15344-2008 | 塑料.再生塑料.聚乙烯(PE)回收物的特性 | Plastics - Recycled Plastics - Characterisation of Polyethylene (PE) recyclates; English version of DIN EN 15344:2008-02 |
| DIN EN 15345-2008 | 塑料.回收的塑料.聚丙烯(PP)回收材料的特征 | Plastics - Recycled Plastics - Characterisation of Polypropylene (PP) recyclates; English version of DIN EN 15345:2008-02 |
| DIN EN 15346-2008 | 塑料.再生塑料.聚氯乙烯(PVC)回收产品 | Plastics - Recycled Plastics - Characterisation of poly(vinyl chloride) (PVC) recyclates; English version of DIN EN 15346:2008-02 |
| DIN EN 15347-2008 | 塑料.再生塑料.塑料废弃物的特性 | Plastics - Recycled Plastics - Characterisation of plastics wastes; English version of DIN EN 15347:2008-02 |
| DIN EN 15348-2008 | 塑料.再生塑料.聚对苯二甲酸乙二酯(PET)再生塑料的特性 | Plastics - Recycled Plastics - Characterisation of poly(ethylene terephthalate) (PET) recyclates; English version of DIN EN 15348:2008-02 |
| DIN EN 15386-2008 | 包装.柔性叠层板和塑料管.测定印刷附着力的试验方法 | Packaging - Flexible laminate and plastic tubes - Test method to determine the print adhesion; English version of DIN EN 15386:2008-01 |
| DIN EN 15416-2-2008 | 苯酚和氨基塑料除外的负荷轴承木结构用粘结剂.试验方法.第2部分:压力剪切多重粘结样品的静载荷试验 | Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 2: Static load test of multiple bondline specimens in compression shear; English version of DIN EN 15416-2:2008-03 |
| DIN EN 15416-3-2008 | 酚和氨基塑料除外的负荷轴承木结构用粘结剂.试验方法.第3部分:带弯曲剪切载荷的试样在循环气候条件下蠕变试 | Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 3: Creep deformation test at cyclic climate conditions with specimens loaded in bending shear; English version of DIN EN 15416-3:2008-03 |
| DIN EN 15416-4-2006 | 苯酚和氨基塑料除外的负荷轴承木结构的粘结剂.试验法.第4部分:一种聚亚安酯粘结剂成分的开放陈化时间测定 | Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 4: Determination of open assembly time for one component polyurethane adhesives; English version EN 15416-4:2006-10 |
| DIN EN 15416-5-2006 | 苯酚和氨基塑料除外的负荷轴承木结构的粘结剂.试验法.第5部分:常规加压时间测定 | Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of conventional pressing time; English version of DIN EN 15416-5:2006-10 |
| DIN EN 1548-2007 | 防水柔性薄板材.屋顶防水用塑料和橡胶薄板材.暴露于沥青中的方法 | Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Method for exposure to bitumen; English version of DIN EN 1548:2007-11 |
| DIN EN 1555-1-2003 | 气体燃料塑料管道供气系统.聚乙烯(PE).第1部分:总则 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General; German version EN 1555-1:2002 |
| DIN EN 1555-2-2003 | 气体燃料塑料管道供气系统.聚乙烯(PE).第2部分:管道 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes; German version EN 1555-2:2002 |
| DIN EN 1555-3-2005 | 气体燃料供应用塑料管道系统.聚乙烯(PE).第3部分:配件 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings; German version EN 1555-3:2002 + A1:2005 |
| DIN EN 1555-4-2003 | 气体燃料塑料管道供气系统.聚乙烯(PE).第4部分:阀门 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves; German version EN 1555-4:2002 |
| DIN EN 1555-5-2003 | 气体燃料塑料管道供气系统.聚乙烯(PE).第5部分:系统的适用性 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system; German version EN 1555-5:2002 |
| DIN EN 15619-2009 | 橡胶或塑料涂覆织物.临时建筑物(帐篷)的安全性.帐篷和相关建筑物用涂层织物的规范 | Rubber or plastic-coated fabrics - Safety of temporary structures (tents) - Specification for coated fabrics intended for tents and related structures; German version EN 15619:2008 |
| DIN EN 1565-1-1999 | 建筑结构中污物和废水排放(低温和高温)用塑料管道系统.苯乙烯共聚掺混料(SAN+PVC).第1部分:管道、管件和系 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system; German version EN 1565-1:1998 |
| DIN EN 1566-1-1999 | 建筑结构中污物和废水排放(低温和高温)用塑料管道系统.氯化聚氯乙烯(PVC-C).第1部分:管道、管件和系统规范 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system; German version EN 1566-1:1998 |
| DIN EN 15702-2009 | 泡沫塑料 软质和硬质聚氨酯用泡沫计数程序 | Cellular Plastics - Cell count procedure for flexible and rigid polyurethane; English version of DIN EN 15702:2009-04 |
| DIN EN 1638-1997 | 塑料管道系统.玻璃纤维增强热固性塑料(GFK)管.圆筒内压循环作用试验方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method for the effects of cyclic internal pressure; German version EN 1638:1997 |
| DIN EN 1680-1997 | 塑料管道系统.聚乙烯(PE)管道系统用阀门.操作机构弯曲时和弯曲后密封性试验方法 | Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanism; German version EN 1680:1997 |
| DIN EN 1704-1997 | 塑料管道系统.热塑管道系统用阀门.弯曲加温度循环后阀门完好性测试方法 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after temperature cycling under bending; German version EN 1704:1997 |
| DIN EN 1705-1997 | 塑料管道系统.热塑阀门.外部冲击后阀门完好性试验方法 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow; German version EN 1705:1996 |
| DIN EN 1716-1997 | 塑料管道系统.聚乙烯(PE)开孔三通.安装就位的开孔三通抗冲击应力试验方法 | Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an asssembled tapping tee; German version EN 1716:1997 |
| DIN EN 1734-1997 | 带橡胶和塑料涂层的织物.水密性测定.低压法 | Rubber- or plastics coated fabrics - Determination of resistance to water penetration - Low pressure method; German version EN 1734:1996 |
| DIN EN 1735-1997 | 带橡胶和塑料涂层的织物.柔韧性测定 | Rubber- or plastics coated fabrics - Determination of flexibility; German version EN 1735:1996 |
| DIN EN 1796-2009 | 有或无压力给水用塑料管道系统.基于不饱和聚酯树脂(UP)的玻璃增强热硬塑料(GRP) | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) (includes Amendment A1:2009); English version of DIN EN 1796:2009-07 |
| DIN EN 1842-1997 | 塑料制品.热固模制件.压模收缩量测定 | Plastics - Thermoset moulding compounds (SMC - BMC) - Determination of compression moulding shrinkage; German version EN 1842:1997 |
| DIN EN 1844-2001 | 防水软板.耐臭氧性测定.屋顶防水塑料和橡胶薄板 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing; German version EN 1844:2001 |
| DIN EN 1848-2-2001 | 防水软板.长度、宽度、平直度和平整度测定.第2部分:屋顶防水塑料和橡胶板. | Flexible sheets for waterproofing - Determination of length, width, straightness and flatness - Part 2: Plastic and rubber sheets for roof waterproofing; German version EN 1848-2:2001 |
| DIN EN 1850-2-2001 | 防水软板.可见缺陷的测定.第2部分:屋顶防水塑料和橡胶板. | Flexible sheets for waterproofing - Determination of visible defects - Part 2: Plastic and rubber sheets for roof waterproofing; German version EN 1850-2:2001 |
| DIN EN 1862-1997 | 塑料管道系统.玻璃纤维增强热固性塑料管(GFK).在化学环境下存放后相对蠕变系数的测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the relative flexural creep factor following exposure to a chemical environment; German version EN 1862:1997 |
| DIN EN 1873-2006 | 屋顶层用预制附件.塑料单个屋顶灯.产品规范和试验方法.德文版本EN 1873-2005 | Prefabricated accessories for roofing - Individual roof lights of plastics - Product specification and test methods; English version of DIN EN 1873:2006-03 |
| DIN EN 1875-3-1998 | 橡胶或塑料涂层的织物.撕裂强度的测定.第3部分:梯形试样法 | Rubber- or plastics-coated fabrics - Determination of tear strength - Part 3: Trapezoidal method; German version EN 1875-3:1997 |
| DIN EN 1876-1-1998 | 橡胶或塑料涂覆织物.低温试验.第1部分:弯曲试验 | Rubber or plastics coated fabrics - Low temperatures tests - Part 1: Bending test; German version EN 1876-1:1997 |
| DIN EN 1876-2-1998 | 橡胶或塑料涂覆织物.低温试验.第2部分:毛圈冲击试验 | Rubber or plastics coated fabrics - Low temperatures tests - Part 2: Impact test on loop; German version EN 1876-2:1997 |
| DIN EN 1903-2008 | 胶粘剂.塑料、橡胶地板覆层或墙面覆层用胶粘剂的试验方法.加速老化后尺寸变化的测定 | Adhesives - Test method for adhesives for plastic or rubber floor coverings or wall coverings - Determination of dimensional changes after accelerated ageing; English version of DIN EN 1903:2008-06 |
| DIN EN 1905-1999 | 塑料管道系统.未增塑的聚氯乙烯(PVC-V)管材、管连接件和材料.根据氯总含量评定聚氯乙烯含量的方法 | Plastics piping systems - Unplastized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on total chlorine content; German version EN 1905:1998 |
| DIN EN 1928-2000 | 防水软板.屋顶防水用沥青、塑料和橡胶薄板.水密性测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of watertightness; German version EN 1928:2000 |
| DIN EN 1931-2001 | 防水软板.屋顶防水用沥青、塑料和橡胶薄板.水蒸汽渗透性测定 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of water vapour transmission properties; German version EN 1931:2000 |
| DIN EN 1979-1999 | 塑料管道和导管系统.热塑性螺旋成形的结构壁管材.接缝抗拉强度的测定 | Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam; German version EN 1979:1999 |
| DIN EN 233-1999 | 卷式壁纸.成品壁纸.聚乙烯壁纸和塑料壁纸规范 | Wall coverings in roll form - Specification for finished wallpapers, wall vinyls and plastics wallcoverings; German version EN 233:1999 |
| DIN EN 2377-1989 | 航空航天系列.玻璃纤维增强的塑料.外表层间抗剪强度的测定 | Aerospace series; glass fibre reinforced plastics; test method; determination of apparent interlaminar shear strength; german version EN 2377:1989 |
| DIN EN 2378-1995 | 航空航天系列.纤维增强塑料.通过浸入测定吸水量; 德文版本 EN 2378:1995 | Aerospace series - Fibre reinforced plastics - Determination of water absorption by immersion; German version EN 2378:1995 |
| DIN EN 2489-1995 | 航空航天系列.纤维增强塑料.试验流体影响的测定; 德文版本 EN 2489:1995 | Aerospace series - Fibre reinforced plastics - Determination of the action of test fluids; German version EN 2489:1995 |
| DIN EN 2561-1995 | 航空航天系列.碳素纤维增强塑料.单向塑料层压制品.纤维方向平行抗拉试验; 德文版本 EN 2561:1995 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Tensile test parallel to the fibre direction; German version EN 2561:1995 |
| DIN EN 2562-1997 | 航空航天系列.碳纤维增强塑料.单向层压塑料.与纤维方向平行的弯曲试验 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates; flexural test parallel to the fibre direction; German version EN 2562:1997 |
| DIN EN 2563-1997 | 航空航天系列.碳纤维增强塑料.单向层压制品.表观层压间抗切强度测定 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates; determination of apparent interlaminar shear strength; German version EN 2563:1997 |
| DIN EN 2564-1998 | 航空航天系列.碳纤维层压塑料.纤维含量、树脂含量和气孔的测定 | Aerospace series - Carbon fibre laminates - Determination of the fibre-, resin- and void contents; German version EN 2564:1998 |
| DIN EN 2597-1998 | 航空航天系列.碳纤维增强的塑料.无向叠层材料.垂直纤维方向的拉力试验 | Aerospace series - Carbon fibre reinforced plastics; unidirectional laminates - Tensile test perpendicular to the fibre direction; German version EN 2597:1998 |
| DIN EN 25978-1993 | 橡胶或塑料涂层织物.抗堵塞性的测定 | Rubber- or plastics-coated fabrics; determination of blocking resistance (ISO 5978:1990); German version EN 25978:1993 |
| DIN EN 26590-2-1993 | 包装.包装袋.术语和类型.第2部分:热塑性塑料柔性薄膜袋 | Packaging; sacks; vocabulary and types; part 2: sacks made from thermoplastic flexible film (ISO 6590-2:1986); german version EN 26590-2:1992 |
| DIN EN 26801-1993 | 橡胶和塑料软管.体积膨胀的测定 | Rubber or plastics hoses; determination of volumetric expansion (ISO 6801:1983); German version EN 26801:1993 |
| DIN EN 2743-2003 | 航空航天系列.纤维增强塑料.测试未老化材料前的标准调整程序 | Aerospace series - Fibre reinforced plastics - Standard procedures for conditioning prior to testing unaged materials; German and English version EN 2743:2001 |
| DIN EN 2746-1998 | 航空航天系列.玻璃纤维增强的塑料.绕曲试验.三点弯曲试验法 | Aerospace series - Glass fibre reinforced plastics - Flexural test, three point bend method; German version EN 2746:1998 |
| DIN EN 2747-1998 | 航空航天系列.玻璃纤维增强塑料.拉伸试验 | Aerospace series - Glass fibre reinforced plastics - Tensile test; German version EN 2747:1998 |
| DIN EN 28029-1993 | 塑料软管.一般用途的纺织物增强的可折叠水管 | Plastics hose; general purpose collapsible water hose, textile reinforced; specification (ISO 8029:1985); German version EN 28029:1993 |
| DIN EN 28233-1991 | 热塑性塑料阀.扭矩.试验方法(ISO 8233-88) | Thermoplastics valves; torques; test method (ISO 8233:1988); german version EN 28233:1990 |
| DIN EN 28659-1991 | 热塑性塑料阀.疲劳强度.试验方法(ISO 8659-88) | Thermoplastic valves; fatigue strength; test method (ISO 8659:1989); german version EN 28659:1990 |
| DIN EN 289-2009 | 塑料机和橡胶机 压力机 安全要求 | Plastics and rubber machines - Presses - Safety requirements(includes Amendment A1:2008); English version of DIN EN 289:2009-06 |
| DIN EN 301-2006 | 承重木结构用酚醛和氨基塑料粘合剂.分类和性能要求 | Adhesives, phenolic and aminoplastic, for load-bearing timber structures - Classification and performance requirements English version of DIN EN 301:2006-09 |
| DIN EN 3475-513-2007 | 航空航天系列.飞行器用电缆.试验方法.第513部分:抗变形(塑料电缆结配置) | Aerospace series - Cables, electrical, aircraft use - Test methods - Part 513: Deformation resistance (Installation with plastic cable ties); German and English version EN 3475-513:2005 |
| DIN EN 3545-001-2009 | 航空航天系列.工作温度-55℃～175℃后部密封或非密封的塑料外壳连接的矩形电气连接器.第001部分:技术规范 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 001: Technical specification; German and English version EN 3545-001:2008 |
| DIN EN 3545-002-2009 | 航空航天系列.工作温度-55℃～175℃后部密封或非密封的、塑料壳体固定装置矩形电气连接器.第002部分:性能和 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 002: Specification of performance and contact arrangements; German and English version EN 3545-002:2008 |
| DIN EN 3545-003-2006 | 航空航天系列.工作温度-55℃至175℃后部密封或非密封的、塑料壳体矩形连接器.第003部分:插孔接点的连接器. | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 003: Connectors with female contacts - Product standard; German and English version EN 3545-003:2005 |
| DIN EN 3545-004-2006 | 航空航天系列.工作温度-55℃至175℃后部密封或非密封的、塑料壳体矩形连接器.第004部分:插塞接点的连接器. | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 004: Connectors with male contacts - Product standard; German and English version EN 3545-004:2005 |
| DIN EN 3545-005-2007 | 航空航天系列.工作温度为-55℃～175℃塑料壳体锁紧装置后部密封或非密封的矩形电连接器.第005部分:不固定外 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 005: Female coding and attachment System for mounting on free housing (plug) - Product standard; German and English version EN 3545-005:2006 |
| DIN EN 3545-006-2007 | 航空航天系列.工作温度为-55℃～175℃塑料壳体锁紧装置后部密封或非密封的矩形电连接器.第006部分:固定外壳 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 006: Male coding and attachment System for mounting on fixed housing (receptacle) - Product standard; German and English version EN 3545-006:2006 |
| DIN EN 3545-007-2006 | 航空航天系列.工作温度-55℃至175℃后部密封或非密封的、塑料壳体矩形连接器.第007部分:电缆夹.产品标准 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 007: Cable clamp - Product standard; German and English version EN 3545-007:2005 |
| DIN EN 3545-008-2008 | 航空航天系列.工作温度为-55℃～175℃、后部带有密封或非密封 塑料壳体锁紧装置的电连接器.第008部分:编码 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 008: Tools for assembly/removal of coding and attachment system - Product standard; German and English version EN 3545-008:2006 |
| DIN EN 3545-009-2009 | 航空航天系列.工作温度为-55℃～175℃、后部带有密封或非密封 塑料壳体锁紧装置的电连接器.第009部分:插头 | Aerospace series - Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures -55 °C to 175 °C - Part 009: Protective cover for plug and receptacle - Product standard; German and English version EN 3545-009:2008 |
| DIN EN 495-5-2001 | 防水软板.低温折弯性测定.第5部分:塑料和橡胶防水薄板 | Flexible sheets for waterproofing - Determination of foldability at low temperature - Part 5: Plastic and rubber sheets for roof waterproofing; German version EN 495-5:2000 |
| DIN EN 579-1993 | 塑料管道系统.网状交联聚乙烯管.溶剂提取法测定聚合度 | Plastics piping systems; crosslinked polyethylene (PE-X) pipes; determination of degree of crosslinking by solvent extraction; German version EN 579:1993 |
| DIN EN 580-2003 | 塑料管道系统.未增塑聚氯乙烯管.规定温度下抗二氯四甲烷的检验方法 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT); German version EN 580:2003 |
| DIN EN 59-1977 | 玻璃纤维增强塑料.用巴氏(Barcol)硬度测量仪测定硬度 | Glass Reinforced Plastics; Measurement of Hardness by Means of a Barcol Impressor |
| DIN EN 60264-4-1-1995 | 绕组线封装.第4部分:试验方法.第1节:热塑性塑料供线盘 | Packaging of winding wires - Part 4: Methods of test; section 1: Delivery spools made from thermoplastic material (IEC 60264-4-1:1989); German version EN 60264-4-1:1994 |
| DIN EN 60674 Bb.1-1999 | 电器用塑料薄膜.型号对比的相关标准目录(1999版) | Plastic films for electrical purposes - List of relevant standards, comparison of types (status of 1999) |
| DIN EN 60674-1-1999 | 电工用塑料薄膜的规范.第1部分:定义和一般要求 | Specification for plastic films for electrical purposes - Part 1: Definitions and general requirements (IEC 60674-1:1980); German version EN 60674-1:1998 |
| DIN EN 60674-2-2002 | 电工用塑料薄膜规范.第2部分:检验方法 (IEC 60674-2:1988 + 技术勘误 1995 + A1:2001); 德文版本 EN 60674- | Specification for plastic films for electrical purposes - Part 2: Methods of test (IEC 60674-2:1988 + Corrigendum 1995 + A1:2001); German version EN 60674-2:1998 + A1:2001 |
| DIN EN 60674-3-1-1999 | 电工用塑料薄膜.第3部分:各种材料规范.第1活页:电容器用双轴线取向的聚丙烯薄膜 | Plastic films for electrical purposes - Part 3: Specifications for individual materials; Sheet 1: Biaxially oriented polypropylene (PP) film for capacitors (IEC 60674-3-1:1998); German version EN 60674-3-1:1998 |
| DIN EN 60674-3-2-1999 | 电工用塑料薄膜规范.第3部分:各种材料规范.第2活页:电绝缘用平衡双轴线取向的聚对苯二甲酸乙二醇酯薄膜的要 | Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials; Sheet 2: Requirements for balanced biaxially oriented polyethylene terephthalate (PET) films used for electrical insulation (IEC 60674-3-2:1992); German version EN 60674-3-2:1998 |
| DIN EN 60674-3-3-1999 | 电工用塑料薄膜规范.第3部分:各种材料规范.第3活页:电绝缘用聚碳酸酯薄膜的要求 | Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials; Sheet 3: Requirements for polycarbonate (PC) films used for electrical insulation (IEC 60674-3-3:1992); German version EN 60674-3-3:1998 |
| DIN EN 60674-3-4 bis 6-1999 | 电工用塑料薄膜规范.第3部分:各种材料的规范.第4-6活页:电绝缘用聚酰亚胺薄膜的要求 | Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials; Sheets 4 to 6: Requirements for polyimide films used for electrical insulation (IEC 60674-3-4 to 6:1993); German version EN 60674-3-4 bis 6:1995 |
| DIN EN 60674-3-7-1999 | 电工用塑料薄膜的规范.第3部分:各种材料的规范.第7活页:电气绝缘用氟乙烯丙烯薄膜要求 | Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials; Sheet 7: Requirements for fluoroethylene-propylene (FEP) films used for electrical insulation (IEC 60674-3-7:1992); German version EN 60674-3-7:1998 |
| DIN EN 60749-31-2003 | 半导体器件.机械和气候试验方法.第31部分:塑料封装器件的易燃性(内部引起的) | Semiconductor devices - Mechanical and climatic test methods - Part 31: Flammability of plastic encapsulated devices (internally induced) (IEC 60749-31:2002 + Corr. 1:2003); German version EN 60749-31:2003 |
| DIN EN 60749-32-2003 | 半导体器件.机械和气候试验方法.第32部分:塑料封装器件的易燃性(外部引起的) | Semiconductor devices - Mechanical and climatic test methods - Part 32: Flammability of plastic-encapsulated devices (externally induced) (IEC 60749-32:2003 + Corr. 1:2003); German version EN 60749-32:2003 + Corr.:2003 |
| DIN EN 61234-1-1994 | 电绝缘材料水解稳定性试验方法.第1部分:塑料薄膜 | Method of test for the hydrolytic stability of electrical insulating materials - Part 1: Plastic films (IEC 61234-1:1994); German version EN 61234-1:1994 |
| DIN EN 61754-21-2005 | 纤维光学连接器接口.第21部分:塑料光纤用SMI型连接器门类 | Fibre optic connector interfaces - Part 21: Type SMI connector family for plastic optical fibre (IEC 61754-21:2005); German version EN 61754-21:2005 |
| DIN EN 61837-1-1999 | 频率控制和选择用表面安装的压电器件.标准外形和终端引线的连接.第1部分:塑料模压外壳外形 | Surface mounted piezoelectric devices for frequency control and selection - Standard outlines and terminal lead connections - Part 1: Plastic moulded enclosure outlines (IEC 61837-1:1999); German version EN 61837-1:1999 |
| DIN EN 62148-4-2004 | 纤维光学有源元件及器件.包装和接口标准.第4部分:PN 1x9塑料光纤无线电收发信机 | Fibre optic active components and devices - Package and interface standards - Part 4: PN 1x9 plastic optical fibre transceivers (IEC 62148-4:2003); German version EN 62148-4:2003 |
| DIN EN 62149-6-2004 | 纤维光学有源元件及器件.性能标准.第6部分:650-nm 250-Mbit/s塑料光纤无线电收发信机 | Fibre optic active components and devices - Performance standards - Part 6: 650-nm 250-Mbit/s plastic optical fibre transceivers (IEC 62149-6:2003); German version EN 62149-6:2003 |
| DIN EN 62300-2005 | 带塑料光纤的用户音频/视频设备数字接口 | Consumer audio/video equipment digital interface with plastic optical fibre (IEC 62300:2004); German version EN 62300:2005 |
| DIN EN 637-1994 | 塑料管道系统.玻璃纤维增强塑料部件.用重力测量法对成分含量的测定; 德文版本 EN 637:1994 | Plastics piping systems - Glass-reinforced plastics components - Determination of the amounts of constituents using the gravimetric method; German version EN 637:1994 |
| DIN EN 705-1994 | 塑料管道系统.玻璃纤维增强热固塑料管和管件.回归分析和应用方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analyses and their use; German version EN 705:1994 |
| DIN EN 712-1994 | 热塑塑料管道系统.压力管和管接头之间承载端部的机械连接.恒定纵向作用力下抗拉出力的试验方法 | Thermoplastics piping systems; end-load bearing mechanical joints between pressure pipes and fittings; test method for resistance to pull-out under constant longitudinal force; German version EN 712:1993 |
| DIN EN 713-1994 | 塑料管道系统.管接头和聚烯烃压力管间的机械连接.在内压和弯曲下密封性的试验方法 | Plastics piping systems; mechanical joints between fittings and polyolefin pressure pipes; test method for leaktightness under internal pressure of assemblies subjected to bending; German version EN 713:1993 |
| DIN EN 715-1994 | 热塑塑料管道系统.小直径压力管和管接头之间承载端部的连接.在水内压力下（包括端头推力）密封试验方法 | Thermoplastics piping systems; end-load bearing joints between small diameter pressure pipes and fittings; test method for leaktightness under internal water pressure, including end thrust; German version EN 715:1994 |
| DIN EN 727-1995 | 塑料管道和管道输送系统.热塑塑料管和管件.维卡软化温度(VST)的测定; 德文版本 EN 727:1994 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST); German version EN 727:1994 |
| DIN EN 728-1997 | 塑料管和管道系统.聚烯烃管和接头.氧化感应时间测定 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time; German version EN 728:1997 |
| DIN EN 744-1995 | 塑料管道和管道输送系统.热塑塑料管.用昼夜连续法的抗内爆的试验方法; 德文版本 EN 744:1995 | Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock-method; German version EN 744:1995 |
| DIN EN 761-1994 | 塑料管道系统.玻璃增强热固性管.干燥条件蠕变系数测定 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under dry conditions; German version EN 761:1994 |
| DIN EN 802-1994 | 塑料管道和管道输送系统.压力管道系统用喷铸热塑管件.压碎造成最大变形的试验方法; 德文版本 EN 802:1994 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for pressure piping systems - Test method for maximum deformation by crushing; German version EN 802:1994 |
| DIN EN 803-1994 | 塑料管道系统.压力管道用橡胶密封圈连接件的热塑喷铸管件.无端部拉力的抗瞬时内压的试验方法; 德文版本 EN | Plastics piping systems - Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust; German version EN 803:1994 |
| DIN EN 804-1994 | 塑料管道系统.压力管道用带胶粘套管连接件的热塑喷铸管件.抗流体静力瞬时内压能力的试验方法; 德文版本 EN | Plastics piping systems - Injection-moulded socket fittings for solvent-cemented joints for pressure piping - Test method for resistance to a short-term internal hydrostatic pressure; German version EN 804:1994 |
| DIN EN 855-1997 | 塑料软管和软管组件.带织物编织层的塑料液压软管.规范 | Plastic hoses and hose assemblies - Thermoplastics textile reinforced hydraulic type - Specification; German version EN 855:1996 |
| DIN EN 911-1995 | 塑料管道系统.热塑塑料压力管道用的弹性密封环型接头和机械接头的连接.外部静力液压条件下的防漏试验方法; | Plastics piping systems - Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - Test method for leaktightness under external hydrostatic pressure; German version EN 911:1995 |
| DIN EN 917-1997 | 塑料管道系统.热塑阀门.耐内压和密封性试验方法 | Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal pressure and leaktightness; German version EN 917:1997 |
| DIN EN 922-1995 | 塑料管道和管道输送系统.未增塑聚氯乙烯管和管件.测定粘度数值和K值计算用试样制备; 德文版本 EN 922:1994 | Plastics piping and ducting systems - Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) - Specimen preparation for determination of the viscosity number and calculation of the K-value; German version EN 922:1994 |
| DIN EN ISO 10082-2000 | 塑料.酚醛树脂.分类和试验方法 | Plastics - Phenolic resins - Classification and test methods (ISO 10082:1999); German version EN ISO 10082:1999 |
| DIN EN ISO 10093-1999 | 塑料.燃烧试验.标准点火源 | Plastics - Fire tests - Standard ignition sources (ISO 10093:1998); German version EN ISO 10093:1998 |
| DIN EN ISO 10350-2-2001 | 塑料.可比单点数据的采集和表示.第2部分:长纤维增强塑料 | Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2001); German version EN ISO 10350-2:2001 |
| DIN EN ISO 10352-1997 | 纤维增强塑料.模制化合物和聚酯胶片.单位面积质量测定 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass per unit area (ISO 10352:1997); German version EN ISO 10352:1997 |
| DIN EN ISO 10366-1-2003 | 塑料.甲基丙烯酸甲酯/丁二烯/苯乙烯共聚物(ABS)的模塑和挤塑材料.第1部分:命名制度和规范基础 | Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 10366-1:2002); German version EN ISO 10366-1:2002 |
| DIN EN ISO 10366-2-2004 | 塑料.甲基丙烯酸甲酯/丙烯腈/丁二烯/苯乙烯(MABS)模塑和挤塑材料.第2部分:试样制备和性能测定 | Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 10366-2:2003); German version EN ISO 10366-2:2003 |
| DIN EN ISO 1043-1-2002 | 塑料符号和缩略语.第1部分:基本聚合物及其专有特性 | Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001); German version EN ISO 1043-1:2002 |
| DIN EN ISO 1043-2-2002 | 塑料制品.符号和缩略语.第2部分:填充剂及加强材料 (ISO 1043-2:2000); 德文版本 EN ISO 1043-2:2001 | Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials (ISO 1043-2:2000); German version EN ISO 1043-2:2001 |
| DIN EN ISO 1043-3-2000 | 塑料.符号和缩略语.第3部分:增塑剂 | Plastics - Symbols and abbreviated terms - Part 3: Plasticizers (ISO 1043-3:1996); German version EN ISO 1043-3:1999 |
| DIN EN ISO 1043-4-2000 | 塑料.符号和缩略语.第4部分:阻燃剂 | Plastics - Symbols and abbreviated terms - Part 4: Flame retardants (ISO 1043-4:1998); German version EN ISO 1043-4:1999 |
| DIN EN ISO 1060-1-2000 | 塑料.氯乙烯的均聚物和共聚物树脂.第1部分:命名体系和规范基础 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications (ISO 1060-1:1998); German version EN ISO 1060-1:1999 |
| DIN EN ISO 1060-2-2000 | 塑料.氯乙烯的均聚物和共聚物树脂.第2部分:试验样品的制备和性能的测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 2: Preparation of test samples and determination of properties (ISO 1060-2:1998); German version EN ISO 1060-2:1999 |
| DIN EN ISO 1061-2000 | 塑料.不增塑的乙酸纤维素.游离酸度的测定 | Plastics - Unplasticized cellulose acetate - Determination of free acidity (ISO 1061:1990); German version EN ISO 1061:1999 |
| DIN EN ISO 10724-1-2002 | 塑料制品.热固粉末模塑复合物试样的喷射成型.第1部分:一般原则和多用途试样的模塑成型 (ISO 10724-1:1998); | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens (ISO 10724-1:1998); German version EN ISO 10724-1:2001 |
| DIN EN ISO 10724-2-2000 | 塑料.热固性粉末模塑复合物试样的注射模塑成型.第2部分:小板材 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 2: Small plates (ISO 10724-2:1998); German version EN ISO 10724-2:2000 |
| DIN EN ISO 10931-2006 | 工业用塑料管道系统.聚偏氟乙烯(PVDF).元件和系统的规范.德文版本EN ISO 10931:2005 | Plastics piping systems for industrial applications - Poly(vinylidene fluoride) (PVDF) - Specifications for components and the system (ISO 10931:2005); English version of DIN EN ISO 10931:2006-03 |
| DIN EN ISO 10960-1996 | 橡胶和塑料软管.动态耐臭氧性评估 | Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions (ISO 10960:1994); German version EN ISO 10960:1996 |
| DIN EN ISO 1110-1998 | 塑料.聚酰胺.试样的加速调节处理 | Plastics - Polyamides - Accelerated conditioning of test specimens (ISO 1110:1995); German version EN ISO 1110:1997 |
| DIN EN ISO 11248-1999 | 塑料.热固模塑材料.高温下短期特性的评定 | Plastics - Thermosetting moulding materials - Evaluation of short-term performance at elevated temperatures (ISO 11248:1993); German version EN ISO 11248:1999 |
| DIN EN ISO 1133-2005 | 塑料.热塑性塑料熔体质量流动速率(MFR)和熔体体积流动速率(MVR)的测定 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005); German version EN ISO 1133:2005 |
| DIN EN ISO 11337-2004 | 塑料.聚酰胺.气相色谱法测定ε-己内酰胺和ω-月桂酰 | Plastics - Polyamides - Determination of -caprolactam and -laurolactam by gas chromatography (ISO 11337:2004); German version EN ISO 11337:2004 |
| DIN EN ISO 11358-1997 | 塑料.聚合物的热重测定.一般原理 | Plastics - Thermogravimetry (TG) of polymers - General principles (ISO 11358:1997); German version EN ISO 11358:1997 |
| DIN EN ISO 11401-1998 | 塑料.酚醛树脂.用液相色谱法分离 | Plastics - Phenolic resins - Separation by liquid chromatography (ISO 11401:1993); German version EN ISO 11401:1998 |
| DIN EN ISO 11403-1-2003 | 塑料.可比较多点数据的采集和表示.第1部分:机械性能 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2001); German version EN ISO 11403-1:2003 |
| DIN EN ISO 11403-2-2004 | 塑料.可比多点数据的采集和表示.第2部分:热性能和加工性能 | Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2004); German version EN ISO 11403-2:2004 |
| DIN EN ISO 11403-3-2002 | 塑料制品.可比较的多点数据采集和表述.第3部分:环境对性能的影响(ISO 11403-3:1999); 德文版本 EN ISO 1140 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:1999); German version EN ISO 11403-3:2001 |
| DIN EN ISO 11409-1998 | 塑料.酚醛树脂.用差示扫描量热法测定反应热和温度 | Plastics - Phenolic resins - Determination of heats and temperatures of reaction by differential scanning calorimetry (ISO 11409:1993); German version EN ISO 11409:1998 |
| DIN EN ISO 11468-1999 | 塑料.聚氯乙烯(PVC)糊剂试样制备.溶解器法 | Plastics - Preparation of PVC pastes for test purposes - Dissolver method (ISO 11468:1997); German version EN ISO 11468:1999 |
| DIN EN ISO 11469-2000 | 塑料.塑料产品通用标识和标记 | Plastics - Generic identification and marking of plastics products (ISO 11469:2000); German version EN ISO 11469:2000 |
| DIN EN ISO 11501-2004 | 塑料.薄膜和薄板.加热尺寸变化的测定 | Plastics - Film and sheeting - Determination of dimensional change on heating (ISO 11501:1995); German version EN ISO 11501:2004 |
| DIN EN ISO 11502-2005 | 塑料.薄膜和薄板.阻尼力测定 | Plastics - Film and sheeting - Determination of blocking resistance (ISO 11502:1995); English version of DIN EN ISO 11502 |
| DIN EN ISO 11542-1-2002 | 塑料制品.超高分子量聚乙烯模塑和挤塑材料.第1部分:标识系统和基本规范(ISO 11542-1:2001);德文版本 EN ISO | Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 11542-1:2001); German version EN ISO 11542-1:2001 |
| DIN EN ISO 1158-1998 | 塑料.氯乙烯均聚物和共聚物.氯含量的测定 | Plastics - Vinyl chloride homopolymers and copolymers - Determination of chlorine content (ISO 1158:1998); German version EN ISO 1158:1998 |
| DIN EN ISO 1163-1-1999 | 塑料.未增塑聚氯乙烯(PVC-U)模塑与挤出材料.第1部分:命名系统与基本规范 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1163-1:1995); German version EN ISO 1163-1:1999 |
| DIN EN ISO 1163-2-1999 | 塑料.未增塑聚氯乙烯(PVC-U)模塑与挤出材料.第2部分:试样制备与性能测定 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1163-2:1995); German version EN ISO 1163-2:1999 |
| DIN EN ISO 11667-1999 | 纤维增强塑料.模塑化合物和聚酯胶片.树脂、增强纤维和矿物填料含量的测定.溶解方法 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of resin, reinforced-fibre and mineral-filler content - Dissolution methods (ISO 11667:1997); German version EN ISO 11667:1999 |
| DIN EN ISO 1172-1998 | 纺织玻璃纤维增强塑料.预浸料坯,模塑化合物及叠层板材.纺织玻璃纤维和矿物填充料含量的测定.煅烧法 | Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content; calcination methods (ISO 1172:1996); German version EN ISO 1172:1998 |
| DIN EN ISO 11758-1997 | 橡胶和塑料软管.氙弧灯曝光.颜色和外观变化 | Rubber and plastics hoses - Exposure to a xenon arc lamp - Determination of changes in colour and appearance (ISO 11758:1995); German version EN ISO 11758:1997 |
| DIN EN ISO 1183-1-2004 | 塑料.非泡沫塑料的密度测定方法.第1部分:浸入法、液体比重瓶法和滴定法 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2004); German version EN ISO 1183-1:2004 |
| DIN EN ISO 1183-2-2004 | 塑料.非泡沫塑料的密度测定方法.第2部分:密度梯度柱法 | Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method (ISO 1183-2:2004); German version EN ISO 1183-2:2004 |
| DIN EN ISO 1183-3-2000 | 塑料.非泡沫塑料的密度测定方法.第3部分:气体比重瓶法 | Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method (ISO 1183-3:1999); German version EN ISO 1183-3:1999 |
| DIN EN ISO 11833-1-2008 | 塑料.未增塑聚氯乙烯薄板.形状、尺寸和特征.第1部分:厚度不低于1mm的薄板 | Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2007); English version of DIN EN ISO 11833-1:2008-01 |
| DIN EN ISO 11833-2-2006 | 塑料.未增塑聚氯乙烯薄板.类型、尺寸和特征.第2部分:厚度低于1mm的薄板 | Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 2 : Sheets of thickness less than 1mm (ISO 11833-2:1998); English version of DIN EN ISO 11833-2:2006-06 |
| DIN EN ISO 119-1998 | 塑料.苯酚-甲醛模塑件.游离酚的测定.碘量法 | Plastics - Phenol-formaldehyde mouldings - Determination of free phenols; Iodometric method (ISO 119:1977); German version EN ISO 119:1998 |
| DIN EN ISO 11963-1995 | 塑料制品.聚碳酸酯板材.型号、尺寸和特性 (ISO 11963:1995); 德文版本 EN ISO 11963:1995 | Plastics - Polycarbonate sheets - Types, dimensions and characteristics (ISO 11963:1995); German version EN ISO 11963:1995 |
| DIN EN ISO 120-1998 | 塑料.苯酚-甲醛模塑件.游离氨和铵化合物的测定.比色法 | Plastics - Phenol-formaldehyde mouldings - Determination of free ammonia and ammonium compounds; Colorimetric comparison method (ISO 120:1977); German version EN ISO 120:1998 |
| DIN EN ISO 12017-1996 | 塑料.聚甲基丙烯酸甲酯双合板和三合板.试验方法 | Plastics - Poly(methyl methacrylate) double- and triple-skin sheets - Test methods (ISO 12017:1995); German version EN ISO 12017:1996 |
| DIN EN ISO 12058-1-2002 | 塑料制品.使用落球式粘度计测定粘度.第1部分:斜管法 (ISO 12058-1:1997); 德文版本 EN ISO 12058-1:2002 | Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997); German version EN ISO 12058-1:2002 |
| DIN EN ISO 12086-1-2006 | 塑料.含氟聚合物分散体模塑和挤压材料.第1部分:命名系统和基本规范 | Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 12086-1:2006); English version of DIN EN ISO 12086-1:2006-05 |
| DIN EN ISO 12086-2-2006 | 塑料.含氟聚合物分散体模塑和挤压材料.第2部分:试样制备和性能测定 | Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 12086-2:2006); English version of DIN EN ISO 12086-2:2006-05 |
| DIN EN ISO 12114-1997 | 纤维增强塑料.热固性模塑化合物和聚酯胶片.固化特性测定 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of cure characteristics (ISO 12114:1997); German version EN ISO 12114:1997 |
| DIN EN ISO 12115-1997 | 纤维增强塑料.热固性模塑化合物和聚酯胶片.流动性、熟化和使用寿命测定 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of flowability, maturation and shelf life (ISO 12115:1997); German version EN ISO 12115:1997 |
| DIN EN ISO 1264-1997 | 塑料.氯乙烯的均聚物和共聚物树脂.水萃物的pH值测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of pH of aqueous extract (ISO 1264:1980); German version EN ISO 1264:1997 |
| DIN EN ISO 1265-2007 | 塑料.聚氯乙烯树脂.杂质和杂质粒子数量的测定 | Plastics - Poly(vinyl chloride) resins - Determination of number of impurities and foreign particles (ISO 1265:2007) English version of DIN EN ISO 1265:2007-05 |
| DIN EN ISO 1269-2007 | 塑料.氯乙烯均聚物和共聚物树脂.挥发性物质(包括水)的测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of volatile matter (including water) (ISO 1269:2006); English version of DIN EN ISO 1269:2007-02 |
| DIN EN ISO 13000-1-2006 | 塑料.聚四氟乙烯(PTFE)半成品.第1部分:要求和名称与符号(ISO 13000-1-2005).德文版本 EN ISO 13000-1-2005 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005); English version of DIN EN ISO 13000-1:2006-02 |
| DIN EN ISO 13000-2-2006 | 塑料.聚四氟乙烯(PTFE)半成品.第2部分:试样的制备和特性的测定 (ISO 13000-2-2005).德文版本 EN ISO 13000- | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005); English version of DIN EN ISO 13000-2:2006-02 |
| DIN EN ISO 1307-2008 | 橡胶和塑料软管.软管尺寸、最小和最大内径及软管定长剪切的公差(ISO 1307-2006).德文版本EN ISO 1307-2008 | Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses (ISO 1307:2006); German version EN ISO 1307:2008 |
| DIN EN ISO 13468-1-1997 | 塑料.透明材料光透射率总量的测定.第1部分:单束光发射仪 | Plastics - Determination of the total luminous transmittance of transparent materials - Part 1: Single-beam instrument (ISO 13468-1:1996); German version EN ISO 13468-1:1996 |
| DIN EN ISO 13468-2-2006 | 塑料.透明材料光透射率总量的测定.第2部分:双束光发射仪(ISO 13468-2:1999) | Plastics - Determination of the total luminous transmittance of transparent materials - Part 2: Double-beam instrument (ISO 13468-2:1999) English version of DIN EN ISO 13468-2:2006-07 |
| DIN EN ISO 13760-1998 | 压力下液体输送用塑料管.Miner法则.累积损坏的计算方法 | Plastics pipes for the conveyance of fluids under pressure - Miner's rule - Calculation method for cumulative damage (ISO 13760:1998); German version EN ISO 13760:1998 |
| DIN EN ISO 13783-1998 | 塑料管体系.未增塑聚氯乙烯(PVC-U)端部承载双套管连接件.在经受弯曲和内压力时检测密封性和机械强度的试验 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints - Test method for leaktightness and strength while subjected to bending and internal pressure (ISO 13783:1997); German version EN ISO 13783:1997 |
| DIN EN ISO 13802-2006 | 塑料.摆锤冲击试验机鉴定.却贝、艾卓德和拉伸冲击试验 | Plastics - Verification of pendulum impact-testing machines - Charpy, Izod and tensile impact-testing (ISO 13802:1999, including Corrigendum 1:2000); English version of DIN EN ISO 13802:2006-06 |
| DIN EN ISO 13844-2000 | 塑料管道系统.用于硬聚氯乙烯(PVC-U)管道的弹性密封圈式承口连接件.负压下密封试验方法 | Plastics piping systems - Elastomeric sealing ring type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure (ISO 13844:2000); German version EN ISO 13844:2000 |
| DIN EN ISO 13845-2000 | 塑料管道系统.用于硬聚氯乙烯(PVC-U)管道的弹性密封圈式承口连接件.内压下角度偏转密封试验方法 | Plastics pipes systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with angular deflection (ISO 13845:2000); German version EN ISO 13845:2000 |
| DIN EN ISO 13846-2001 | 塑料管道系统.热塑承压管用端部荷载轴承和无端部荷载轴承组件和连接件.测定水内压长期密封性的试验方法 | Plastic piping systems - End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaktightness under internal water pressure (ISO 13846:2000); German version EN ISO 13846:2000 |
| DIN EN ISO 13927-2003 | 塑料.用锥形辐射加热器和热电堆探测器进行简单热释放试验 | Plastics - Simple heat release test using a conical radiant heater and a thermopile detector (ISO 13927:2001); German version EN ISO 13927:2003 |
| DIN EN ISO 13968-2009 | 塑料管和管道系统.热塑性塑料管.环形挠性的测定 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility (ISO 13968:2008); English version of DIN EN ISO 13968:2009-01 |
| DIN EN ISO 14113-2009 | 气焊设备.450巴(45MPa)以下工业气体传输用橡胶和塑料软管及其组件 | Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2007); German version EN ISO 14113:2008 |
| DIN EN ISO 14125-1998 | 纤维增强塑料.弯曲性能测定 | Fibre-reinforced plastic composites - Determination of flexural properties (ISO 14125:1998); German version EN ISO 14125:1998 |
| DIN EN ISO 14126-2000 | 纤维增强塑料混合物.水平方向压缩能力的测定 | Fibre-reinforced plastic composites - Determination of compressive properties in the in-plane direction (ISO 14126:1999); German version EN ISO 14126:1999 |
| DIN EN ISO 14129-1998 | 纤维增强塑料符合材料.用45角度拉伸试验方法测定平面内剪切应力/剪切应变响应关系，包括平面内剪切模数/强 | Fibre-reinforced plastic composites - Determination of the in-plane shear stress/shear strain reponse, including the in-plane schear modulus and strength, by ? 45° tension test method (ISO 14129:1997); German version EN ISO 14129:1997 |
| DIN EN ISO 14130-1998 | 纤维增强塑料符合材料.用短梁法测定表面层间剪切强度 | Fibre reinforced plastic composites - Determination of apparent interlaminar shear strength by short beam-method (ISO 14130:1997); German version EN ISO 14130:1997 |
| DIN EN ISO 1421-1998 | 橡胶和塑料涂层的织物.抗拉强度和延伸率的测定 | Rubber- or plastics-coated fabrics - Determination of tensile strength and elongation at break (ISO 1421:1998); German version EN ISO 1421:1998 |
| DIN EN ISO 14526-1-2000 | 塑料.酚醛粉末模塑化合物(PF-PMCs).第1部分:命名体系及基本规范 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 1: Designation system and basis for specifications (ISO 14526-1:1999); German version EN ISO 14526-1:1999 |
| DIN EN ISO 14526-2-2000 | 塑料.酚醛粉末模塑化合物(PF-PMCs).第2部分:试样的制备和性能的测定 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14526-2:1999); German version EN ISO 14526-2:1999 |
| DIN EN ISO 14526-3-2000 | 塑料.酚醛粉末模塑化合物(PF-PMCs).第3部分:对所选模塑化合物的要求 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14526-3:1999); German version EN ISO 14526-3:1999 |
| DIN EN ISO 14527-1-2000 | 塑料.脲醛和脲/蜜胺酚醛粉末模塑化合物(UF-和UF/MF-PMCs).第1部分:名称体系和基本规范 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 1: Designation system and basis for specifications (ISO 14527-1:1999); German version EN ISO 14527-1:1999 |
| DIN EN ISO 14527-2-2000 | 塑料.脲醛和脲/蜜胺酚醛粉末模塑化合物(UF-和UF/MF-PMCs).第2部分:试样的制备和特性的测定 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14527-2:1999); German version EN ISO 14527-2:1999 |
| DIN EN ISO 14527-3-2000 | 塑料.脲醛和脲/蜜胺酚醛粉末模塑化合物(UF-和UF/MF-PMCs).第3部分:对所选模塑化合物的要求 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14527-3:1999); German version EN ISO 14527-3:1999 |
| DIN EN ISO 14528-1-2000 | 塑料.蜜胺酚醛粉末模塑化合物(MF-PMCs).第1部分:命名系统和基本规范 | Plastics - Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Part 1: Designation system and basis for specifications (ISO 14528-1:1999); German version EN ISO 14528-1:1999 |
| DIN EN ISO 14528-2-2000 | 塑料.蜜胺甲醛粉末模塑化合物(MF-PMCs).第2部分:试样准备和特性测定 | Plastics - Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14528-2:1999); German version EN ISO 14528-2:1999 |
| DIN EN ISO 14528-3-2000 | 塑料.蜜胺酚醛粉末模塑化合物(MF-PMCs).第3部分:对所选模塑化合物的要求 | Plastics - Melamine-formaldehyde powder moulding compounds (MF-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14528-3:1999); German version EN ISO 14528-3:1999 |
| DIN EN ISO 14529-1-2000 | 塑料.蜜胺/酚醛粉末模塑化合物(MP-PMCs).第1部分:命名体系和基本规范 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 1: Designation system and basis for specifications (ISO 14529-1:1999); German version EN ISO 14529-1:1999 |
| DIN EN ISO 14529-2-2000 | 塑料.蜜胺/酚醛粉末模塑化合物(MP-PMCs).第2部分:试样的制备和特性的测定 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14529-2:1999); German version EN ISO 14529-2:1999 |
| DIN EN ISO 14529-3-2000 | 塑料.蜜胺/酚醛粉末模塑化合物(MP-PMCs).第3部分:对选择的模塑化合物的要求 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14529-3:1999); German version EN ISO 14529-3:1999 |
| DIN EN ISO 14530-1-2000 | 塑料.不饱和聚酯粉末模塑化合物(UP-PMCs).第1部分:命名体系和基础规范 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 1: Designation system and basis for specifications (ISO 14530-1:1999); German version EN ISO 14530-1:1999 |
| DIN EN ISO 14530-2-2000 | 塑料.非饱和聚酯粉末模塑化合物(UP-PMCs).第2部分:试样制备和特性测定 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14530-2:1999); German version EN ISO 14530-2:1999 |
| DIN EN ISO 14530-3-2000 | 塑料.非饱和聚酯粉末模塑化合物(UP-PMCs).第3部分:对所选模塑化合物的要求 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14530-3:1999); German version EN ISO 14530-3:1999 |
| DIN EN ISO 14557-2008 | 消防水龙带.橡胶和塑料吸水软管和软管组件 | Fire-fighting hoses - Rubber and plastics suction hoses and hose assemblies (ISO 14557:2002 + AMD 1:2007)(includes Amendment A1:2007); English version of DIN EN ISO 14557:2008-01 |
| DIN EN ISO 14616-2004 | 塑料.聚乙烯、乙烯共聚物及其混合物的热可缩薄膜.收缩应力的测定 | Plastics - Heatshrinkable films of polyethylene, ethylene copolymers and their mixtures - Determination of shrinkage stress and contraction stress (ISO 14616:1997); German version EN ISO 14616:2004 |
| DIN EN ISO 14663-1-2006 | 塑料.乙烯/乙烯醇(EVOH)共聚物模塑和挤塑材料.第1部分:命名系统和基本规范 | Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 1 : Designation system and basis for specifications (ISO 14663-1:1999); English version of DIN EN ISO 14663-1:2006-06 |
| DIN EN ISO 14663-2-2006 | 塑料.乙烯/乙烯醇(EVOH)共聚物模塑和挤塑材料.第2部分:试样制备和性能测定 | Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 14663-2:1999); English version of DIN EN ISO 14663-2:2006-06 |
| DIN EN ISO 14692-1-2005 | 石油和天然气工业.玻璃纤维增强塑料(GRP)管.第1部分:词汇、符号、应用和材料 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2002); English version EN ISO 14692-1:2002 |
| DIN EN ISO 14692-2 Berichtigung 1-2007 | 石油和天然气工业.玻璃纤维增强塑料.第2部分:生产资格 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002); English version EN ISO 14692-2:2002, Corrigenda to DIN EN ISO 14692-2:2005-07; English version EN ISO 14692-2:2002/AC:2006 |
| DIN EN ISO 14692-2-2005 | 石油和天然气工业.玻璃纤维增强塑料(GRP)管.第2部分:合格鉴定和制造 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002); English version EN ISO 14692-2:2002 |
| DIN EN ISO 14692-3 Berichtigung 1-2007 | 石油和天然气工业.玻璃纤维增强塑料管.第3部分:系统管道 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2002); English version EN ISO 14692-3:2002, Corrigenda to DIN EN ISO 14692-3:2005-07; English version EN ISO 14692-3:2002/AC:2006 |
| DIN EN ISO 14692-3-2005 | 石油和天然气工业.玻璃纤维增强塑料(GRP)管.第3部分:系统设计 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2002); English version EN ISO 14692-3:2002 |
| DIN EN ISO 14692-4-2005 | 石油和天然气工业.玻璃纤维增强塑料(GRP)管.第4部分:制造、安装和操作 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2002); English version EN ISO 14692-4:2002 |
| DIN EN ISO 14851-2004 | 水介质中塑料材料的富氧菌生物降解性的测定.封闭呼吸器中测定需氧量的方法 | Determination of the ultimate aerobic biodegradability of plastic materials in an aqueous medium - Method by measuring the oxygen demand in a closed respirometer (ISO 14851:1999); German version EN ISO 14851:2004 |
| DIN EN ISO 14852-2004 | 水介质中塑料材料的富氧菌生物降解性的测定.二氧化碳增量分析法 | Determination of the ultimate aerobic biodegradability of plastic materials in an aqueous medium - Method by analysis of evolved carbon dioxide (ISO 14852:1999); German version EN ISO 14852:2004 |
| DIN EN ISO 14855-1-2008 | 塑料材料在受控堆肥环境下最终需氧生物降解能力的测定.二氧化碳增量分析法.第1部分:通用方法 | Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions - Method by analysis of evolved carbon dioxide - Part 1: General method (ISO 14855-1:2005); German version EN ISO 14855-1:2007 |
| DIN EN ISO 14890-2005 | 输送带.通用织物结构的橡胶或塑料包覆的输送带规范 | Conveyor belts - Specification for rubber or plastics covered conveyor belts of textile construction for general use (ISO 14890:2003); English version of DIN EN ISO 14890:2005 |
| DIN EN ISO 14910-1-2006 | 塑料.热塑聚酯/酯和聚醚/酯模塑和挤塑弹性体.第1部分:命名系统和基本规范 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 1 : Designation system and basis for specifications (ISO 14910-1:1997); English version of DIN EN ISO 14910-1:2006-06 |
| DIN EN ISO 14910-2-2006 | 塑料.热塑聚酯/酯和聚醚/酯模塑和挤塑弹性体.第2部分:试样制备和性能测定 | Plastics -Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2 : Preparation of test specimens and determination of properties (ISO 14910-2:1997); English version of DIN EN ISO 14910-2:2006-06 |
| DIN EN ISO 15013-2008 | 塑料.聚丙烯挤薄板片材(PP).要求和试验方法 | Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2007); English version of DIN EN ISO 15013:2008-01 |
| DIN EN ISO 15015-2008 | 塑料.冲击改良的丙烯腈-苯乙烯共聚物挤压片材(ABS、AEPDS和ASA).要求和试验方法 | Plastics - Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA) - Requirements and test methods (ISO 15015:2007); English version of DIN EN ISO 15015:2008-01 |
| DIN EN ISO 15023-1-2006 | 塑料.聚乙烯醇(PVAL)材料.第1部分:规范用命名体系和依据 | Plastics - Poly(vinyl alcohol) (PVAL) materials - Part 1: Designation system and basis for specifications (ISO 15023-1:2001); English version of DIN EN ISO 15023-1:2006-06 |
| DIN EN ISO 15023-2-2006 | 塑料.聚乙烯醇(PVAL)材料.第2部分:特性的测定 | Plastics - Poly(vinyl alcohol) (PVAL) materials - Part 2 : Determination of properties (ISO 15023-2:2003); English version of DIN EN ISO 15023-2:2006-06 |
| DIN EN ISO 15103-2-2007 | 塑料.聚苯醚(PPE)模制和挤压成型材料.第2部分:试样制备和特性测定(ISO 15103-2:2007) | Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15103-2:2007); English version of DIN EN ISO 15103-2:2007-09 |
| DIN EN ISO 15106-1-2005 | 塑料.薄膜和薄片.水蒸气传输率的测定.第1部分:湿度探测传感器法 | Plastics - Film and sheeting - Determination of water vapour transmission rate - Part 1: Humidity detection sensor method (ISO 15106-1:2003); German version EN ISO 15106-1:2005 |
| DIN EN ISO 15106-2-2005 | 塑料.薄膜和薄片.水蒸气传输率的测定.第2部分:红外探测传感器法 | Plastics - Film and sheeting - Determination of water vapour transmission rate - Part 2: Infrared detection sensor method (ISO 15106-2:2003); German version EN ISO 15106-2:2005 |
| DIN EN ISO 15106-3-2005 | 塑料.薄膜和薄片.水蒸气传输率的测定.第3部分:电解探测传感器法 | Plastics - Film and sheeting - Determination of water vapour transmission rate - Part 3: Electrolytic detection sensor method (ISO 15106-3:2003); German version EN ISO 15106-3:2005 |
| DIN EN ISO 15252-1-2000 | 塑料.环氧树脂模塑化合物(EP-PMCs).第1部分:命名系统和基本规范 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 1: Designation system and basis for specifications (ISO 15252-1:1999); German version EN ISO 15252-1:1999 |
| DIN EN ISO 15252-2-2000 | 塑料.环氧树脂粉末模塑化合物(EP-PMCs).第2部分:试样的制备和特性的测定 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 15252-2:1999); German version EN ISO 15252-2:1999 |
| DIN EN ISO 15252-3-2000 | 塑料.环氧树脂粉末模塑化合物(EP-PMCs).第3部分:对所选模塑化合物的要求 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 15252-3:1999); German version EN ISO 15252-3:1999 |
| DIN EN ISO 15310-2005 | 纤维增强塑料复合材料.用板捻法测定内剪模量 | Fibre-reinforced plastic composites - Determination of the in-plane shear modulus by the plate twist method (ISO 15310:1999); English version of DIN EN ISO 15310 |
| DIN EN ISO 15493-2003 | 工业用塑料管道系统.丙烯腈-丁二烯-苯乙烯塑料(ABS)、未增塑的聚氯乙烯(PVC-U)和氯化聚氯乙烯(PVC-C).元件 | Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specifications for components and the system; Metric series (ISO 15493:2003); German version EN ISO 15493:2003 |
| DIN EN ISO 15494-2003 | 工业用塑料管道系统.聚丁烯(PE)、聚乙烯(PE)和聚丙烯(PP).元件和系统的规范.米制系列 | Plastics piping systems for industrial applications - Polybutylene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the system; Metric series (ISO 15494:2003); German version EN ISO 15494:2003 |
| DIN EN ISO 15526-1-2004 | 塑料.聚酮模塑和挤塑材料.第1部分:命名系统和基本规范 | Plastics - Polyketone(PK)moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 15526-1:2000); German version EN ISO 15526-1:2004 |
| DIN EN ISO 15526-2-2004 | 塑料.聚酮模塑和挤塑材料.第2部分:试验样品的制备和性能测定 | Plastics - Polyketone(PK)moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15526-2:2000); German version EN ISO 15526-2:2004 |
| DIN EN ISO 15747-2005 | 静脉注射用塑料容器 | Plastics containers for intravenous injection (ISO 15747:2003); German version EN ISO 15747:2005 |
| DIN EN ISO 15791-1-2005 | 塑料.塑料产品用中等规模燃烧试验的设计和应用.第1部分:一般指南 | Plastics - Development and use of intermediate-scale fire tests for plastics products - Part 1: General guidance (ISO 15791-1:2002); German version EN ISO 15791-1:2004 |
| DIN EN ISO 15874-1-2004 | 冷热水装置用塑料管道系统.聚丙烯(PP).第1部分:总则 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO 15874-1:2003); German version EN ISO 15874-1:2003 |
| DIN EN ISO 15874-1/A1-2007 | 冷热水装置用塑料管道系统.聚丙烯(PP).第1部分:总则.修改件1(ISO 15874-1:2003/Amd 1:2007) | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General - Amendment 1 (ISO 15874-1:2003/Amd 1:2007); English version of DIN EN ISO 15874-1:2003/A1:2007-09 |
| DIN EN ISO 15874-2-2004 | 冷热水装置用塑料管道系统.聚丙烯(PP).第2部分:管道 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2003); German version EN ISO 15874-2:2003 |
| DIN EN ISO 15874-2/A1-2007 | 冷热水装置用塑料管道系统.聚丙烯(PP).第2部分:管道.修改件1 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes - Amendment 1 (ISO 15874-2:2003/Amd 1:2007); English version of DIN EN ISO 15874-2:2003/A1:2007-09 |
| DIN EN ISO 15874-3-2004 | 冷热水装置用塑料管道系统.聚丙烯(PP).第3部分:配件 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings (ISO 15874-3:2003); German version EN ISO 15874-3:2003 |
| DIN EN ISO 15874-5-2004 | 冷热水装置用塑料管道系统.聚丙烯(PP).第5部分:系统的适应性 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO 15874-5:2003); German version EN ISO 15874-5:2003 |
| DIN EN ISO 15875-1-2004 | 冷热水装置用塑料管道设备.交联聚乙烯(PE-X).第1部分:总则 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General (ISO 15875-1:2003); German version EN ISO 15875-1:2003 |
| DIN EN ISO 15875-1/A1-2007 | 冷热水装置用塑料管道系统.交联聚乙烯(PE-X).第1部分:总则.修改件1(ISO 15875-1:2003/Amd 1:2007) | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General - Amendment 1 (ISO 15875-1:2003/Amd 1:2007); English version of DIN EN ISO 15875-1:2003/A1:2007-09 |
| DIN EN ISO 15875-2-2004 | 冷热水装置用塑料管道设备.交联聚乙烯(PE-X).第2部分:管道 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes (ISO 15875-2:2003); German version EN ISO 15875-2:2003 |
| DIN EN ISO 15875-2/A1-2007 | 冷热水装置用塑料管道系统.交联聚乙烯(PE-X).第2部分:管.修改件1 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes - Amendment 1 (ISO 15875-2:2003/Amd 1:2007); English version of DIN EN ISO 15875-2:2003/A1:2007-09 |
| DIN EN ISO 15875-3-2004 | 冷热水装置用塑料管道设备.交联聚乙烯(PE-X).第3部分:配件 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO 15875-3:2003); German version EN ISO 15875-3:2003 |
| DIN EN ISO 15875-5-2004 | 冷热水装置用塑料管道设备.交联聚乙烯(PE-X).第5部分:系统的适应性 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO 15875-5:2003); German version EN ISO 15875-5:2003 |
| DIN EN ISO 15876-1-2004 | 冷热水装置用塑料管道设备.聚丁烯(PB).第1部分:总则 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General (ISO 15876-1:2003); German version EN ISO 15876-1:2003 |
| DIN EN ISO 15876-1/A1-2007 | 冷热水装置用塑料管道设备.聚丁烯(PB).第1部分:总则.修改件1 (ISO 15876-1:2003/Amd 1:2007) | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General - Amendment 1 (ISO 15876-1:2003/Amd 1:2007); English version of DIN EN ISO 15876-1:2003/A1:2007-09 |
| DIN EN ISO 15876-2-2004 | 冷热水装置用塑料管道设备.聚丁烯(PB).第2部分:管道 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2: Pipes (ISO 15876-2:2003); German version EN ISO 15876-2:2003 |
| DIN EN ISO 15876-2/A1-2007 | 冷热水装置用塑料管道设备.聚丁烯(PB).第2部分:管道.修改件1 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2: Pipes - Amendment 1 (ISO 15876-2:2003/Amd 1:2007); English version of DIN EN ISO 15876-2:2003/A1:2007-09 |
| DIN EN ISO 15876-3-2004 | 冷热水装置用塑料管道设备.聚丁烯(PB).第3部分:配件 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 3: Fittings (ISO 15876-3:2003); German version EN ISO 15876-3:2003 |
| DIN EN ISO 15876-5-2004 | 冷热水装置用塑料管道设备.聚丁烯(PB).第5部分:系统的适应性 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2003); German version EN ISO 15876-5:2003 |
| DIN EN ISO 15908-2003 | 塑料管道系统粘合剂.测定粘合剂热稳定性的试验方法 | Adhesives for thermoplastic piping systems - Test method for the determination of thermal stability of adhesive (ISO 15908:2002); German version EN ISO 15908:2002 |
| DIN EN ISO 1598-1999 | 塑料.乙酸纤维素.不可溶解成份的测定(ISO 1598-1999) | Plastics - Cellulose acetate - Determination of insoluble particles (ISO 1598:1990); German version EN ISO 1598:1999 |
| DIN EN ISO 1599-2000 | 塑料.乙酸纤维素.模塑时粘度降低的测定 | Plastics - Cellulose acetate - Determination of viscosity loss on moulding (ISO 1599:1990); German version EN ISO 1599:1999 |
| DIN EN ISO 1600-2000 | 塑料.乙酸纤维素.利用加热的不同周期在模制样品生产中的光吸收量的测定 | Plastics - Cellulose acetate - Determination of light absorption on moulded specimens produced using different periods of heating (ISO 1600:1990); German version EN ISO 1600:1999 |
| DIN EN ISO 16101-2004 | 包装.危险货物的运输包装.塑料的兼容性试验 | Packaging - Transport packaging for dangerous goods - Plastics compatibility testing (ISO 16101:2004); German version EN ISO 16101:2004 |
| DIN EN ISO 16103-2005 | 包装.危险物品的运输包装.再循环的塑料 | Packaging - Transport packaging for dangerous goods - Recycled plastics material (ISO 16103:2005); English version of DIN EN ISO 16103 |
| DIN EN ISO 16135 Berichtigung 1-2008 | 工业阀.热塑性塑料材料的球闸阀 | Industrial valves - Ball valves of thermoplastics materials (ISO 16135:2006); German version EN ISO 16135:2006, Corrigenda to DIN EN ISO 16135:2006-06 |
| DIN EN ISO 16136 Berichtigung 1-2008 | 工业阀门.热塑性塑料材料的蝶形阀.技术勘误DIN EN ISO 16136-2006 | Industrial valves - Butterfly valves of thermoplastics materials (ISO 16136:2006); German version EN ISO 16136:2006, Corrigenda to DIN EN ISO 16136:2006-06 |
| DIN EN ISO 16137 Berichtigung 1-2008 | 工业阀门.热塑性塑料材料的止回阀.技术勘误DIN EN ISO 16137-2006 | Industrial valves - Check valves of thermoplastics materials (ISO 16137:2006); German version EN ISO 16137:2006, Corrigenda to DIN EN ISO 16137:2006-06 |
| DIN EN ISO 16138 Berichtigung 1-2008 | 工业阀门.热塑性塑料材料的隔膜阀 | Industrial valves - Diaphragm valves of thermoplastics materials (ISO 16138:2006); German version EN ISO 16138:2006, Corrigenda to DIN EN ISO 16138:2006-06 |
| DIN EN ISO 16139 Berichtigung 1-2008 | 工业阀门.热塑性塑料材料的闸阀.技术勘误DIN EN ISO 16139-2006 | Industrial valves - Gate valves of thermoplastics materials (ISO 16139:2006); German version EN ISO 16139:2006, Corrigenda to DIN EN ISO 16139:2006-06 |
| DIN EN ISO 1622-1-1999 | 塑料.聚苯乙烯(PS)模塑与挤出材料.第1部分:命名体系与基础规范 | Plastics - Polystyrene (PS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1622-1:1994); German version EN ISO 1622-1:1999 |
| DIN EN ISO 1622-2-1999 | 塑料.聚苯乙烯(PS)模塑与挤塑材料.第2部分:试样的制备和性能的测定 | Plastics - Polystyrene (PS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1622-2:1995); German version EN ISO 1622-2:1999 |
| DIN EN ISO 1624-2002 | 塑料制品.氯乙烯均聚物和共聚物树脂.水滤筛析 (ISO 1624:2001); 德文版本 EN ISO 1624:2001 | Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis in water (ISO 1624:2001); German version EN ISO 1624:2001 |
| DIN EN ISO 1628-2-1999 | 塑料.用毛细管粘度计测定稀释溶液中聚合物的粘度.第2部分:聚氯乙烯树脂 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscosimeters - Part 2: Poly(vinyl chloride) resins (ISO 1628-2:1998); German version EN ISO 1628-2:1998 |
| DIN EN ISO 1628-3-2003 | 塑料.用毛细管粘度计测定稀溶液中聚合物的粘度.第3部分:聚乙烯和聚丙烯 | Plastics - Determination of viscosity of polymers in dilute solution using capillary viscometers - Part 3: Polyethylenes and polypropylenes (ISO 1628-3:2001); German version EN ISO 1628-3:2003 |
| DIN EN ISO 1675-1998 | 塑料.液态树脂.用比重计法测定浓度 | Plastics - Liquid resins - Determination of density by the pyknometer method (ISO 1675:1985); German version EN ISO 1675:1998 |
| DIN EN ISO 16871-2003 | 塑料管道系统.塑料管道和配件.自然风化法 | Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering (ISO 16871:2003); German version EN ISO 16871:2003 |
| DIN EN ISO 172-1998 | 塑料.苯酚-甲醛模塑件.游离氨的检测 | Plastics - Phenol-formaldehyde mouldings - Detection of free ammonia (ISO 172:1978); German version EN ISO 172:1998 |
| DIN EN ISO 1746-2000 | 橡胶或塑料软管和管道.弯曲试验 | Rubber or plastics hoses and tubing - Bending tests (ISO 1746:1998, including Technical Corrigendum 1:1999); German version EN ISO 1746:2000 |
| DIN EN ISO 175-2000 | 塑料.测定液体化学品对塑料影响的试验方法 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:1999); German version EN ISO 175:2000 |
| DIN EN ISO 17556-2005 | 塑料.通过呼吸测定器中需氧量的测定或放出的二氧化碳量的测量测定土壤中的最大需氧生物降解能力 | Plastics - Determination of the ultimate aerobic biodegradability in soil by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved (ISO 17556:2003); German version EN ISO 17556:2004 |
| DIN EN ISO 176-2005 | 塑料.增塑剂损耗的测定.活性碳法 | Plastics - Determination of loss of plasticizers - Activated carbon method (ISO 176:2005); German version EN ISO 176:2005 |
| DIN EN ISO 177-1999 | 塑料.增塑剂分散性的测定 | Plastics - Determination of migration of plasticizers (ISO 177:1988); German version EN ISO 177:1999 |
| DIN EN ISO 178-2006 | 塑料.弯曲性能测定 | Plastics - Determination of flexural properties (ISO 178:2001 + AMD 1:2004); (includes Amendment A1:2005) English version of DIN EN ISO 178:2006-04 |
| DIN EN ISO 179-1-2006 | 塑料.摆锤冲击特性测定.第1部分:非仪器冲击试验 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2000 + Amd.1:2005); Enlish version of DIN EN ISO 179-1:2006-05 |
| DIN EN ISO 179-2-2000 | 塑料.摆锤冲击特性测定.第2部分:带测量仪器的冲击试验 | Plastics - Determination of Charpy impact properties - Part 2: Instrumented impact test (ISO 179-2:1997); German version EN ISO 179-2:1999 |
| DIN EN ISO 1797-2-1995 | 牙科旋转器具.柄.第2部分:塑料柄 | Dental rotary instruments - Shanks - Part 2: Shanks made of plastics (ISO 1797-2:1992); German version EN ISO 1797-2:1995 |
| DIN EN ISO 180-2007 | 塑料.伊兆特(Izod)冲击强度测定 | Plastics - Determination of Izod impact strength (ISO 180:2000 + Amd.1:2006); (includes Amendment A1:2006) English version of DIN EN ISO 180:2007-04 |
| DIN EN ISO 182-2-2000 | 塑料.基于氯乙烯共聚物、均聚物的化合物及产物在高温下析出氯化氢和其它酸性产物的趋势测定.第2部分:pH值法 | Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 2: pH method (ISO 182-2:1990); German version EN ISO 182-2:1999 |
| DIN EN ISO 182-3-2001 | 塑料.基于氯乙烯均聚物、共聚物的化合物和产品在高温下析出氯化氢和其它酸性产品的趋势测定.第3部分:电导测 | Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 3: Conductometric method (ISO 182-3:1993); German version EN ISO 182-3:2000 |
| DIN EN ISO 182-4-2001 | 塑料.基于氯乙烯均聚物、共聚物的化合物和产品在高温下析出氯化氢和其它酸性产品的趋势测定.第4部分:电位测 | Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 4: Potentiometric method (ISO 182-4:1993); German version EN ISO 182-4:2000 |
| DIN EN ISO 1872-1-1999 | 塑料.聚乙烯(PE)模塑和挤出材料.第1部分:命名体系与基础规范 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1872-1:1993); German version EN ISO 1872-1:1999 |
| DIN EN ISO 1872-2-2007 | 塑料.聚乙烯(PE)模塑和挤塑材料.第2部分:试样的制备和特性的测定 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1872-2:2007)English version of DIN EN ISO 1872-2:2007-05 |
| DIN EN ISO 1873-1-1995 | 塑料.聚丙烯(PP)模塑和挤塑材料.第1部分:标示系统和规范基础 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1873-1:1995); German version EN ISO 1873-1:1995 |
| DIN EN ISO 1873-2-2007 | 塑料.聚丙烯(PP)模塑和挤塑材料.第2部分:试样的制备和性能的测定 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1873-2:2007); English version of DIN EN ISO 1873-2:2007-11 |
| DIN EN ISO 1874-1-2001 | 塑料.注塑和挤塑用聚酰胺(PA)模塑材料.第1部分:命名 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation (ISO 1874-1:1992); German version EN ISO 1874-1:2000 |
| DIN EN ISO 1874-2-2007 | 塑料.聚酰胺(PA)注塑和压塑材料.第2部分:试样制备和性能测定 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2006); English version of DIN EN ISO 1874-2:2007-04 |
| DIN EN ISO 1923-1995 | 泡沫塑料和橡胶.线性尺寸的测定 (ISO 1923:1981); 德文版本 EN ISO 1923:1995 | Cellular plastics and rubbers - Determination of linear dimensions (ISO 1923:1981); German version EN ISO 1923:1995 |
| DIN EN ISO 20200-2005 | 塑料.在实验室试验中模拟堆肥处理条件下测定塑料的分解度 | Plastics - Determination of the degree of disintegration of plastic materials under simulated composting conditions in a laboratory-scale test (ISO 20200:2004); English version of DIN EN ISO 20200 |
| DIN EN ISO 2039-1-2003 | 塑料.硬度测定.第1部分:球压入法 | Plastics - Determination of hardness - Part 1: Ball indentation method (ISO 2039-1:2001); German version EN ISO 2039-1:2003 |
| DIN EN ISO 2039-2-2000 | 塑料.硬度的测定.第2部分:洛氏硬度 | Plastics - Determination of hardness - Part 2: Rockwell hardness (ISO 2039-2:1987); German version EN ISO 2039-2:1999 |
| DIN EN ISO 20848-1-2008 | 包装.塑料鼓形桶.第1部分:标称容量为113.6L～220L的可拆卸盖式(密封盖)鼓形桶 | Packaging - Plastics drums - Part 1: Removable head (open head) drums with a nominal capacity of 113,6 l to 220 l (ISO 20848-1:2006); German version EN ISO 20848-1:2008 |
| DIN EN ISO 20848-2-2008 | 包装.塑料鼓形桶.第2部分:标称容量为208.1L和220L、不可拆卸的盖式(密封盖)鼓形桶 | Packaging - Plastics drums - Part 2: Non-removable head (tight head) drums with a nominal capacity of 208,2 l and 220 l (ISO 20848-2:2006); German version EN ISO 20848-2:2008 |
| DIN EN ISO 20848-3-2008 | 包装.塑料鼓形桶.第3部分:标称容量113.6L～220L塑料鼓形桶的塞子闭合系统 | Packaging - Plastics drums - Part 3: Plug/bung closure systems for plastics drums with a nominal capacity of 113,6 l to 220 l (ISO 20848-3:2006); German version EN ISO 20848-3:2008 |
| DIN EN ISO 2114 Berichtigung 1-2006 | 塑料制品(聚脂树脂)、涂料和清漆(粘合剂).部分酸值和总酸值的测定(ISO 2114:2000) | Plastics (polyester resins) and paints and varnishes (binders) - Determination of partial acid value and total acid value (ISO 2114:2000); German version EN ISO 2114:2000, Corrigenda to DIN EN ISO 2114:2002-06; German version EN ISO 2114:2000/AC:2005 |
| DIN EN ISO 2114-2002 | 塑料制品(聚酯树脂)和涂料清漆(粘合剂).局部和全部酸值的测定 (ISO 2114:2000); 德文版本 EN ISO 2114:2000 | Plastics (polyester resins) and paints varnishes (binders) - Determination of partial acid value and total acid value (ISO 2114:2000); German version EN ISO 2114:2000 |
| DIN EN ISO 21627-2-2004 | 塑料.环氧树脂.氯含量的测定.第2部分:易皂化的氯 | Plastics - Epoxy resins - Determination of chlorine content - Part 2: Easily saponifiable chlorine (ISO 21627-2:2002); German version EN ISO 21627-2:2003 |
| DIN EN ISO 21787 Berichtigung 1-2008 | 工业阀门.热塑性塑料材料的球阀.技术勘误DIN EN ISO 21787-2006 | Industrial valves - Globe valves of thermoplastics materials (ISO 21787:2006); German version EN ISO 21787:2006, Corrigenda to DIN EN ISO 21787:2006-06 |
| DIN EN ISO 22088-1-2006 | 塑料制品.耐环境应力开裂(ESC)的测定.第1部分:通用指南(ISO 22088-1:2006) | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 1: General guidance (ISO 22088-1:2006); English version of DIN EN ISO 22088-1:2006-11 |
| DIN EN ISO 22088-2-2006 | 塑料制品.耐环境应力开裂(ESC)的测定.第2部分:持续拉伸负荷法(ISO 22088-2:2006) | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 2: Constant tensile load method (ISO 22088-2:2006); English version of DIN EN ISO 22088-2:2006-11 |
| DIN EN ISO 22088-3-2006 | 塑料制品.耐环境应力开裂(ESC)的测定.第3部分:弯带法(ISO 22088-3:2006) | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 3: Bent strip method (ISO 22088-3:2006); English version of DIN EN ISO 22088-3:2006-11 |
| DIN EN ISO 22088-4-2006 | 塑料.耐环境应力碎裂的测定(ESC).第4部分:球或钉压力法(ISO 22088-4:2006) | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 4: Ball or pin impression method (ISO 22088-4:2006); English version of DIN EN ISO 22088-4:2006-11 |
| DIN EN ISO 2231-1995 | 橡胶或塑料涂层织物.环境作用和检验用标准大气压 (ISO 2231:1989); 德文版本 EN ISO 2231:1995 | Rubber- or plastics-coated fabrics - Standard atmospheres for conditioning and testing (ISO 2231:1989); German version EN ISO 2231:1995 |
| DIN EN ISO 2286-1-1998 | 橡胶或塑料涂层的织物.卷织物特性的测定.第1部分:长度、宽度和净质量的测定 | Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 1: Method for determination of the length, width and net mass (ISO 2286-1:1998); German version EN ISO 2286-1:1998 |
| DIN EN ISO 2286-2-1998 | 橡胶或塑料涂层的织物.卷织物特性的测定.第2部分:单位面积总质量、单位面积涂层质量和基布的单位面积质量的 | Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 2: Methods for determination of total mass per unit area, mass per unit area of coating and mass per unit area of substrate (ISO 2286-2:1998); German version EN ISO 2286-2:1998 |
| DIN EN ISO 2286-3-1998 | 橡胶或塑料涂层的织物.卷织物特性的测定.第3部分:单位面积的整体的质量,单位面积涂层的质量和单位面积基布 | Rubber- or plastic-coated fabrics - Determination of roll characteristics - Part 3: Method for determination of thickness (ISO 2286-3:1998); German version EN ISO 2286-3:1998 |
| DIN EN ISO 23667-2007 | 包装.危险物品的运输包装.硬性塑料和塑料合成IBCs.兼容性测试 | Packaging - Transport packaging for dangerous goods - Rigid plastics and plastics composite IBCs - Compatibility testing (ISO 23667:2007) English version of DIN EN ISO 23667:2007-10 |
| DIN EN ISO 2411-2000 | 橡胶或塑料涂覆织物.涂层粘合强度的测定 | Rubber- or plastics-coated fabrics - Determination of coating adhesion (ISO 2411:2000); German version EN ISO 2411:2000 |
| DIN EN ISO 24998-2009 | 塑料实验室器皿 微生物过程用单用途皮氏培养皿 | Plastics laboratory ware - Single-use Petri dishes for microbiological procedures (ISO 24998:2008); English version of DIN EN ISO 24998:2009-03 |
| DIN EN ISO 2535-2003 | 塑料.不饱和聚酯树脂.室温胶凝时间测量 | Plastics - Unsaturated polyester resins - Measurement of gel time at ambient temperature (ISO 2535:2001); German version EN ISO 2535:2002 |
| DIN EN ISO 2554-1998 | 塑料.不饱和聚酯树脂.羟基值的测定 | Plastics - Unsaturated polyester resins - Determination of hydroxyl value (ISO 2554:1997); German version EN ISO 2554:1998 |
| DIN EN ISO 2555-2000 | 塑料.液态或乳态或分散状的树脂.用布洛克非尔德试验测定表面粘度 | Plastics - Resins in the liquid state or as emulsions or dispersions - Determination of apparent viscosity by the Brookfield test method (ISO 2555:1989); German version EN ISO 2555:1999 |
| DIN EN ISO 2556-2001 | 塑料.大气压力下薄膜和薄板的透气率的测定.测压法 | Plastics - Determination of the gas transmission rate of films and thin sheets under atmospheric pressure - Manometric method (ISO 2556:1974); German version EN ISO 2556:2000 |
| DIN EN ISO 2578-1998 | 塑料.长期热作用下温度 - 时间极限值的测定 | Plastics - Determination of time-temperature limits after prolonged exposure to heat (ISO 2578:1993); German version EN ISO 2578:1998 |
| DIN EN ISO 2580-1-2003 | 塑料.丙烯腈-丁二烯-苯乙烯共聚物(ABS)模塑和挤塑材料.第1部分:命名制度和规范基础 | Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2002); German version EN ISO 2580-1:2002 |
| DIN EN ISO 2580-2-2004 | 塑料.丙烯腈-丁二烯-苯乙烯共聚物(ABS)的模塑和挤塑材料.第2部分:试样制备和性能测定 | Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2580-2:2003); German version EN ISO 2580-2:2003 |
| DIN EN ISO 2818-1997 | 塑料.试样机械加工制备 | Plastics - Preparation of test specimens by machining (ISO 2818:1994); German version EN ISO 2818:1996 |
| DIN EN ISO 28941-1-2009 | 塑料 聚苯醚(PPE)模制和挤压成型材料 第1部分:命名体系和规范基础 | Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 28941-1:2008); English version of DIN EN ISO 28941-1:2009-04 |
| DIN EN ISO 2897-1-1999 | 塑料.耐冲击聚苯乙烯模塑和挤出材料.第1部分:命名体系与基础规范 | Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2897-1:1997); German version EN ISO 2897-1:1999 |
| DIN EN ISO 2897-2-2004 | 塑料.耐冲击聚苯乙烯(PS-I)模塑和挤塑材料.第2部分:试样制备和性能测定 | Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2897-2:2003); German version EN ISO 2897-2:2003 |
| DIN EN ISO 2898-1-1999 | 塑料.增塑聚氯乙烯(PVC-P)模塑与挤出材料.第1部分:命名系统与基本规范 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2898-1:1996); German version EN ISO 2898-1:1999 |
| DIN EN ISO 2898-2-2009 | 塑料.增塑聚氯乙烯(PVC-P)模塑和挤塑材料.第2部分:试样制备和性能测定 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2898-2:2008); English version of DIN EN ISO 2898-2:2009-03 |
| DIN EN ISO 291-2008 | 塑料.调节和测试用标准大气 | Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008); German version EN ISO 291:2008 |
| DIN EN ISO 293-2005 | 塑料.热塑性材料试样的压模铸造 | Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2004); English version of DIN EN ISO 293 |
| DIN EN ISO 294-1-1998 | 塑料.热塑性塑料试件的注模塑法.第1部分:一般原理、多用途模塑件及条形试件 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:1996); German version EN ISO 294-1:1998 |
| DIN EN ISO 294-2-2006 | 塑料.热塑性材料试样的注模塑法.第2部分:小拉伸棒 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars (ISO 294-2:1996 + Amd.1:2004); English version of DIN EN ISO 294-2:2006-05 |
| DIN EN ISO 294-3-2003 | 塑料.热塑性材料试样的注模塑法.第3部分:小板 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2002); German version EN ISO 294-3:2003 |
| DIN EN ISO 294-4-2003 | 塑料.热塑材料试样的注塑法.第4部分:模塑收缩率的测定 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4: Determination of moulding shrinkage (ISO 294-4:2001); German version EN ISO 294-4:2003 |
| DIN EN ISO 295-2004 | 塑料.热固性材料试样的压模塑法 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004); German version EN ISO 295:2004 |
| DIN EN ISO 3001-1999 | 塑料.环氧化合物.环氧基当量的测定 | Plastics - Epoxide compounds - Determination of epoxide equivalent (ISO 3001:1999); German version EN ISO 3001:1999 |
| DIN EN ISO 305-1999 | 塑料.聚氯乙烯和有关含氯的均聚物、共聚物及其混合物的热稳定性的测定.色变法 | Plastics - Determination of thermal stability of poly(vinyl chloride), related chlorine-containing homopolymers and copolymers and their compounds - Discoloration method (ISO 305:1990); German version EN ISO 305:1999 |
| DIN EN ISO 306-2004 | 塑料.热塑性材料.维卡特(VICAT)软化温度的测定(VST) | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2004); German version EN ISO 306:2004 |
| DIN EN ISO 307-2007 | 塑料.聚酰胺.粘度值的测定(ISO 307-2007) | Plastics - Polyamides - Determination of viscosity number (ISO 307:2007); English version of DIN EN ISO 307:2007-08 |
| DIN EN ISO 308-1998 | 塑料.酚醛树脂模塑材料.丙酮可溶物质的测定(未模塑材料的表面树脂含量) | Plastics - Phenolic moulding materials - Determination of acetone-soluble matter (apparent resin content of material in the unmoulded state) (ISO 308:1994); German version EN ISO 308:1997 |
| DIN EN ISO 3126-2005 | 塑料管道系统.塑料部件.尺寸测定 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005); German version EN ISO 3126:2005 |
| DIN EN ISO 3146-2002 | 塑料制品.采用毛细管和偏振光显微镜法对半晶状聚合物的熔化性能(熔化温度或熔化区域)的测定 (ISO 3146:2000 | Plastics - Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods (ISO 3146:2000); German version EN ISO 3146:2000 |
| DIN EN ISO 3167-2003 | 塑料.多用途试样 | Plastics - Multipurpose test specimens (ISO 3167:2002); German version EN ISO 3167:2003 |
| DIN EN ISO 3219-1994 | 塑料制品.液态或乳液或漂移的聚合物/树脂.使用规定剪切率的旋转式粘度计测定粘度 (ISO 3219:1993); 德文版 | Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate (ISO 3219:1993); German version EN ISO 3219:1994 |
| DIN EN ISO 3251-2008 | 涂料、清漆和塑料.非挥发物质含量的测定 | Paints, varnishes and plastics - Determination of non-volatile-matter content (ISO 3251:2008); German version EN ISO 3251:2008 |
| DIN EN ISO 3451-1-2008 | 塑料.灰份测定.第1部分:一般方法 | Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:2008); English version of DIN EN ISO 3451-1:2008-11 |
| DIN EN ISO 3451-4-2001 | 塑料.灰分测定.第4部分:聚酰胺 | Plastics - Determination of ash - Part 4: Polyamides (ISO 3451-4:1998); German version EN ISO 3451-4:2000 |
| DIN EN ISO 3451-5-2002 | 塑料制品.灰分的测定.第5部分:聚氯乙烯 (ISO 3451-5:2002); 德文版本 EN ISO 3451-5:2002 | Plastics - Determination of ash - Part 5: Poly(vinyl chloride) (ISO 3451-5:2002); German version EN ISO 3451-5:2002 |
| DIN EN ISO 3521-1999 | 塑料.不饱和聚酯和环氧树脂.体积的总收缩量的测定 | Plastics - Unsaturated polyester and epoxy resins - Determination of overall volume shrinkage (ISO 3521:1997); German version EN ISO 3521:1999 |
| DIN EN ISO 3671-1998 | 塑料.氨基模塑材料.挥发性物质的测定 | Plastics - Aminoplastic moulding materials - Determination of volatile matter (ISO 3671:1976); German version EN ISO 3671:1998 |
| DIN EN ISO 3672-1-2002 | 塑料制品.不饱和的聚酯树脂.第1部分:标识体系 (ISO 3672-1:2000); 德文版本 EN ISO 3672-1:2001 | Plastics - Unsaturated-polyester resins (UP-R) - Part 1: Designation system (ISO 3672-1:2000); German version EN ISO 3672-1:2001 |
| DIN EN ISO 3672-2-2002 | 塑料制品.不饱和的聚酯树脂.第2部分:试样制备和性能测定 (ISO 3672-2:2000); 德文版本 EN ISO 3672-2:2001 | Plastics - Unsaturated-polyester resins (UP-R) - Part 2: Preparation of test specimens and determination of properties (ISO 3672-2:2000); German version EN ISO 3672-2:2001 |
| DIN EN ISO 3673-1-1999 | 塑料.环氧树脂.第1部分:命名 | Plastics - Epoxy resins - Part 1: Designation (ISO 3673-1:1996); German version EN ISO 3673-1:1999 |
| DIN EN ISO 3673-2-2000 | 塑料.环氧树脂.第2部分:试验样品的制备和特性的测定 | Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties (ISO 3673-2:1999); German version EN ISO 3673-2:1999 |
| DIN EN ISO 3826-1-2004 | 人体血液和血液成分用折式塑料容器.第1部分:常规容器 | Plastics collapsible containers for human blood and blood components - Part 1: Conventional containers (ISO 3826-1:2003); German version EN ISO 3826-1:2003 |
| DIN EN ISO 3826-2-2008 | 人类血液及血液成分用塑料可折叠容器.第2部分:用于标签和说明手册上的图形符号 | Plastics collapsible containers for human blood and blood components - Part 2: Graphical symbols for use on labels and instruction leaflets (ISO 3826-2:2008); English version of DIN EN ISO 3826-2:2008-11 |
| DIN EN ISO 3826-3-2008 | 人体血液和血液成分用可折叠塑料容器.第3部分:带综合特征的采血袋系统(ISO 3826-3-2006) | Plastics collapsible containers for human blood and blood components - Part 3: Blood bag systems with integrated features (ISO 3826-3:2006); English version of DIN EN ISO 3826-3:2008-03 |
| DIN EN ISO 3915-1999 | 塑料.导电塑料电阻率的测量 | Plastics - Measurement of resistivity of conductive plastics (ISO 3915:1981); German version EN ISO 3915:1999 |
| DIN EN ISO 3994-2000 | 塑料软管.给排含水物质用螺旋热塑塑料增强的热塑塑料软管.规范 | Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification (ISO 3994:1998); German version EN ISO 3994:2000 |
| DIN EN ISO 4080-1995 | 橡胶和塑料软管和软管组件.透气性测定 (ISO 4080:1991); 德文版本 EN ISO 4080:1995 | Rubber and plastics hoses and hose assemblies - Determination of permeability to gas (ISO 4080:1991); German version EN ISO 4080:1995 |
| DIN EN ISO 4577-1999 | 塑料.聚丙烯和丙烯共聚物.空气中热氧化稳定性的测定.烘箱法 | Plastics - Polypropylene and propylene-copolymers - Determination of thermal oxidative stability in air, oven method (ISO 4577:1983); German version EN ISO 4577:1999 |
| DIN EN ISO 4589-1-1999 | 塑料.通过氧指数测定其燃烧性.第1部分:指南 | Plastics - Determination of burning behaviour by oxygen index - Part 1: Guidance (ISO 4589-1:1996); German version EN ISO 4589-1:1999 |
| DIN EN ISO 4589-2-2006 | 塑料.通过氧含量测定塑料燃烧性.第2部分:高温试验 | Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test (ISO 4589-2:1996 + Amd. 1:2005)(includes Amendment A1:2006) English version of DIN EN ISO 4589-2:1999 + A1:2006-06 |
| DIN EN ISO 4589-3-1996 | 塑料.通过氧指数测定塑料燃烧性.第3部分:高温试验 | Plastics - Determination of burning behaviour by oxygen index - Part 3: Elevated-temperature test (ISO 4589-3:1996); German version EN ISO 4589-3:1996 |
| DIN EN ISO 4590-2003 | 硬质泡沫塑料.开孔和闭孔容积百分数测定 | Rigid cellular plastics - Determination of the volume percentage of open cells and of closed cells (ISO 4590:2002); German version EN ISO 4590:2003 |
| DIN EN ISO 4608-1998 | 塑料.一般用途的氯乙烯均聚物和共聚物树脂.室温下增塑剂吸收性的测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride for general use - Determination of plasticizer absorption at room temperature (ISO 4608:1998); German version EN ISO 4608:1998 |
| DIN EN ISO 4610-2002 | 塑料制品.氯乙烯均聚物和共聚物树脂.使用气喷式筛滤器械的筛选分析 (ISO 4610:2001); 德文版本 EN ISO 4610 | Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis using air-jet sieve apparatus (ISO 4610:2001); German version EN ISO 4610:2001 |
| DIN EN ISO 4611-2009 | 塑料.暴露于湿热、溅水和盐雾中影响的测定 | Plastics - Determination of the effects of exposure to damp heat, water spray and salt mist (ISO 4611:2008); English version of DIN EN ISO 4611:2009-02 |
| DIN EN ISO 4612-1999 | 塑料.测试用途的聚氯乙烯(PVC)膏料制备.行星式混合器方法 | Plastics - Preparation of PVC pastes for testing purposes - Planetary-mixer method (ISO 4612:1999); German version EN ISO 4612:1999 |
| DIN EN ISO 4613-1-1999 | 塑料.乙酸乙烯/乙烯基乙酸酯(E/VAC)模塑和挤出材料.第1部分:名称与规范（ISO 4613-1-1993) | Plastics - Ethylen/vinyl acetate (E/VAC) moulding and extrusion materials - Part 1: Designation and specification (ISO 4613-1:1993); German version EN ISO 4613-1:1999 |
| DIN EN ISO 4613-2-2004 | 塑料.乙酸乙烯/乙烯酯(E/VAC)模塑和挤塑材料.第2部分:试验样品的制备和性能测定 | Plastics - Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 4613-2:1995 + AMD 1:2004); German version EN ISO 4613-2:1995 + A1:2004 |
| DIN EN ISO 4614-2000 | 塑料.三聚氰胺--甲醛模塑件.可萃取的甲醛的测定 | Plastics - Melamine-formaldehyde mouldings - Determination of extractable formaldehyde (ISO 4614:1977); German version EN ISO 4614:1999 |
| DIN EN ISO 4615-2000 | 塑料.不饱和聚酯和环氧树脂.氯总含量的测定 | Plastics - Unsaturated polyesters and epoxide resins - Determination of total chlorine content (ISO 4615:1979); German version EN ISO 4615:1999 |
| DIN EN ISO 4651-1995 | 泡沫橡胶和塑料.动态抗震性能的测定 (ISO 4651:1988); 德文版本 EN ISO 4651:1995 | Cellular rubbers and plastics - Determination of dynamic cushioning performance (ISO 4651:1988); German version EN ISO 4651:1995 |
| DIN EN ISO 4651/A1-2008 | 泡沫橡胶和塑料.动态抗震性能的测定.修改件1 | Cellular rubbers and plastics - Determination of dynamic cushioning performance - Amendment 1 (ISO 4651:1988/AMD 1:2006); English version of DIN EN ISO 4651:1995/A1:2008-11 |
| DIN EN ISO 4672-1999 | 橡胶和塑料软管.低于室温的柔性试验 | Rubber and plastics hoses - Sub-ambient temperature flexibility tests (ISO 4672:1997); German version EN ISO 4672:1999 |
| DIN EN ISO 4674-1-2003 | 橡胶或塑料涂覆织物.抗撕裂性测定.第1部分:撕裂恒速率法 | Rubber- or plastics-coated fabrics - Determination of tear resistance - Part 1: Constant rate of tear methods (ISO 4674-1:2003); German version EN ISO 4674-1:2003 |
| DIN EN ISO 4674-2-1998 | 橡胶或塑料涂层的织物.抗撕裂强度的测定.第2部分:冲击摆试验法 | Rubber or plastics-coated fabrics - Determination of tear resistance - Part 2: Ballistic pendulum method (ISO 4674-2:1998); German version EN ISO 4674-2:1998 |
| DIN EN ISO 472-2002 | 塑料.术语 | Plastics - Vocabulary (ISO 472:1999); German version EN ISO 472:2001 |
| DIN EN ISO 483-2006 | 塑料.为保持恒定湿度使用水溶液进行调节和试验用的小型密封容器(ISO 483-2005).德文版本 EN ISO 483-2005 | Plastics - Small enclosures for conditioning and testing using aqueous solutions to maintain the humidity at a constant value (ISO 483:2005); English version of DIN EN ISO 483:2006-02 |
| DIN EN ISO 489-1999 | 塑料.折射指数测定 | Plastics - Determination of the refractive index (ISO 489:1999); German version EN ISO 489:1999 |
| DIN EN ISO 4892-1-2001 | 塑料.实验室光源暴露方法.第1部分:通用指南 | Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:1999); German version EN ISO 4892-1:2000 |
| DIN EN ISO 4892-3-2006 | 塑料.实验室光源暴露法.第3部分:UV荧光灯 | Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2006); English version of DIN EN ISO 4892-3:2006-05 |
| DIN EN ISO 4894-1-1999 | 塑料.苯乙烯/丙烯腈(SAN)共聚物的模塑和挤塑材料.第1部分:命名体系和基本规范 | Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 4894-1:1997); German version EN ISO 4894-1:1999 |
| DIN EN ISO 4894-2-1999 | 塑料.苯乙烯/丙烯腈(SAN)共聚物的模塑和挤塑材料.第2部分:性能的测定 | Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 4894-2:1995); German version EN ISO 4894-2:1999 |
| DIN EN ISO 4895-1999 | 塑料.液态环氧树脂.结晶趋向的测定 | Plastics - Liquid epoxy resins - Determination of tendency to crystallize (ISO 4895:1997); German version EN ISO 4895:1999 |
| DIN EN ISO 527-1-1996 | 塑料.拉伸性能测定.第1部分:总则 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:1993 including Corr 1:1994); German version EN ISO 527-1:1996 |
| DIN EN ISO 527-2-1996 | 塑料制品.拉伸性能的测定.第2部分:模塑和挤塑制品的试验条件 (ISO 527-2:1993、包括技术勘误 1:1994); 德文 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:1993, including Corr. 1:1994); German version EN ISO 527-2:1996 |
| DIN EN ISO 527-3-2003 | 塑料.抗拉性能的测定.第3部分:薄膜和片材的试验条件（包括勘误AC-1998和AC-2002） | Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets (ISO 527-3:1995 + Corr 1:1998 + Corr 2:2001) (includes Corrigendum AC:1998 + AC:2002); German version EN ISO 527-3:1995 + AC:1998 + AC:2002 |
| DIN EN ISO 527-4-1997 | 塑料.拉伸性能测定.第4部分:均质和非均质增强纤维塑料复合材料试验条件 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and anisotropic fibre-reinforced plastic composites (ISO 527-4:1997); German version EN ISO 527-4:1997 |
| DIN EN ISO 5470-1-1999 | 涂覆橡胶或塑料的织物.耐磨性的测定.第1部分:泰伯磨损检验器（ISO 5470-1-1999) | Rubber- or plastics-coated fabrics - Determination of abrasion resistance - Part 1: Taber abrader (ISO 5470-1:1999); German version EN ISO 5470-1:1999 |
| DIN EN ISO 5470-2-2003 | 橡胶或塑料涂层织物.耐磨性测定.第2部分:马丁代尔研磨器 | Rubber- or plastics-coated fabrics - Determination of abrasion resistance - Part 2: Martindale abrader (ISO 5470-2:2003); German version EN ISO 5470-2:2003 |
| DIN EN ISO 5659-1-1999 | 塑料.烟雾产生.第1部分:光密度试验的导则 | Plastics - Smoke generation - Part 1: Guidance on optical-density testing (ISO 5659-1:1996); German version EN ISO 5659-1:1999 |
| DIN EN ISO 5659-2-2007 | 塑料.烟雾产生.第2部分:用独立燃烧室检验测定光密度 | Plastics - Smoke generation - Part 2: Determination of optical density by a single-chamber test (ISO 5659-2:2006); English version of DIN EN ISO 5659-2:2007-04 |
| DIN EN ISO 5774-2008 | 塑料软管.压缩空气设备用织物增强型.规范 | Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2006); German version EN ISO 5774:2008 |
| DIN EN ISO 580-2005 | 塑料管和管道系统.喷射铸造热塑性配件.热效应直观评估法 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005); German version EN ISO 580:2005 |
| DIN EN ISO 584-1998 | 塑料.未饱和的聚酯树脂.80℃时反应性的测定(常规方法) | Plastics - Unsaturated polyester resins - Determination of reactivity at 80 °C (conventional method) (ISO 584:1982); German version EN ISO 584:1997 |
| DIN EN ISO 585-2000 | 塑料.不增塑的乙酸纤维素.含水量的测定 | Plastics - Unplasticized cellulose acetate - Determination of moisture content (ISO 585:1990); German version EN ISO 585:1999 |
| DIN EN ISO 5981-2008 | 橡胶或塑料涂层织物.抗复合弯曲剪切和磨损的测定 | Rubber- or plastics-coated fabrics - Determination of resistance to combined shear flexing and rubbing (ISO 5981:2007); English version of DIN EN ISO 5981:2008-01 |
| DIN EN ISO 5999-2008 | 软质多孔聚合材料.不包括地毯底衬的过载设施用聚氨酯泡沫塑料.规范 | Flexible cellular polymeric materials - Polyurethane foam for load-bearing applications excluding carpet underlay - Specification (ISO 5999:2007); English version of DIN EN ISO 5999:2008-01 |
| DIN EN ISO 60-2000 | 塑料.专用漏斗注入的材料表观密度的测定 | Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:1977); German version EN ISO 60:1999 |
| DIN EN ISO 604-2003 | 塑料.压缩性能的测定 | Plastics - Determination of compressive properties (ISO 604:2002); German version EN ISO 604:2003 |
| DIN EN ISO 61-2000 | 塑料.不能用专用漏斗注入的模塑材料表观密度的测定 | Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:1976); German version EN ISO 61:1999 |
| DIN EN ISO 6186-1998 | 塑料.松散性的测定 | Plastics - Determination of pourability (ISO 6186:1998); German version EN ISO 6186:1998 |
| DIN EN ISO 62-2008 | 塑料.吸水性测定 | Plastics - Determination of water absorption (ISO 62:2008); German version EN ISO 62:2008 |
| DIN EN ISO 6383-1-2004 | 塑料.薄膜和薄板.耐撕裂性的测定.第1部分:裤型撕裂法 | Plastics - Film and sheeting - Determination of tear resistance - Part 1: Trouser tear method (ISO 6383-1:1983); German version EN ISO 6383-1:2004 |
| DIN EN ISO 6383-2-2004 | 塑料.薄膜和薄板.耐撕裂性的测定.第2部分:埃尔曼多法 | Plastics - Film and sheeting - Determination of tear resistance - Part 2: Elmendorf method (ISO 6383-2:1983); German version EN ISO 6383-2:2004 |
| DIN EN ISO 6401-2008 | 塑料.聚氯乙烯.剩余氯乙烯单体的测定.气相色谱法(ISO 6401-2008).英文版本DIN EN ISO 6401-2008 | Plastics - Poly(vinyl chloride) - Determination of residual vinyl chloride monomer - Gas-chromatographic method (ISO 6401:2008); English version of DIN EN ISO 6401:2008-12 |
| DIN EN ISO 6402-1-2003 | 塑料.丙烯腈-苯乙烯-丙烯酸酯、丙烯腈-(乙烯-丙烯-二烯烃)-苯乙烯和丙烯腈-(氯化聚乙烯)-苯乙烯模制和挤压 | Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 1: Designation system and basis for specification (ISO 6402-1:2002); German version EN ISO 6402-1:2002 |
| DIN EN ISO 6402-2-2004 | 塑料.丙烯腈-苯乙烯-丙烯酸酯(ASA)、丙烯腈-(乙烯-丙烯-二烯烃)-苯乙烯(AEPDS)和丙烯腈-(氯化聚乙烯)-苯乙 | Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:2003); German version EN ISO 6402-2:2003 |
| DIN EN ISO 6603-1-2000 | 塑料.硬质塑料耐冲孔性能的测定.第1部分:非仪器冲击试验 | Plastics - Determination of puncture impact behaviour of rigid plastics - Part 1: Non-instrumented impact testing (ISO 6603-1:2000); German version EN ISO 6603-1:2000 |
| DIN EN ISO 6603-2-2002 | 塑料制品.硬质塑料制品击穿性能的测定.第2部分:仪器冲孔试验 (ISO 6603-2:2000); 德文版本 EN ISO 6603-2:2 | Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented puncture test (ISO 6603-2:2000); German version EN ISO 6603-2:2000 |
| DIN EN ISO 6721-1-2003 | 塑料.动态机械性能测定.第1部分:一般原理 | Plastics - Determination of dynamic mechanical properties - Part 1: General principles (ISO 6721-1:2001); German version EN ISO 6721-1:2002 |
| DIN EN ISO 6721-2-2008 | 塑料.动力学机械性能测定.第2部分:扭转-摇摆方法 | Plastics - Determination of dynamic mechanical properties - Part 2: Torsion-pendulum method (ISO 6721-2:2008); English version of DIN EN ISO 6721-2:2008-09 |
| DIN EN ISO 6721-3-1996 | 塑料.电动机械性能测定.第3部分:弯曲振动.共振法 | Plastics - Determination of dynamic mechanical properties - Part 3: Flexural vibration; resonance-curve (ISO 6721-3:1994, including Technical Corrigendum 1:1995); German version EN ISO 6721-3:1996 |
| DIN EN ISO 6802-2010 | 钢丝增强的橡胶和塑料软管及软管组件.弯曲液压脉冲试验 | Rubber and plastics hoses and hose assemblies with wire reinforcements - Hydraulic impulse test with flexing (ISO 6802:2005); German version EN ISO 6802:2008 |
| DIN EN ISO 6803-1997 | 橡胶和塑料软管及软管组件.无弯曲液压压力脉冲试验 | Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803:1994); German version EN ISO 6803:1997 |
| DIN EN ISO 6808-2000 | 给排油用塑料软管及软管组件.规范 | Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification (ISO 6808:1999); German version EN ISO 6808:2000 |
| DIN EN ISO 7214-2007 | 泡沫塑料.聚乙烯.试验方法 | Cellular plastics - Polyethylene - Methods of test (ISO 7214:2007); German version EN ISO 7214:2007 |
| DIN EN ISO 7233-2008 | 橡胶和塑料软管及软管组件.耐真空性能的测定 | Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum (ISO 7233:2006); German version EN ISO 7233:2008 |
| DIN EN ISO 7327-1997 | 塑料.环氧树脂固化剂和催化剂.酸酐中游离酸测定 | Plastics - Hardeners and accelerators for epoxide resins - Determination of free acid in acid anhydride (ISO 7327:1994); German version EN ISO 7327:1997 |
| DIN EN ISO 7391-1-2006 | 塑料.聚碳酸酯模塑和挤塑材料.第1部分:命名体系和基础规范 | Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 7391-1:2006); English version of DIN EN ISO 7391-1:2006-06 |
| DIN EN ISO 7391-2-2006 | 塑料.聚碳酸酯模塑和挤塑材料.第2部分:试样制备和特性测定 | Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7391-2:2006); English version of DIN EN ISO 7391-2:2006-06 |
| DIN EN ISO 75-1-2004 | 塑料.载荷下变形温度的测定.第1部分:一般试验方法 | Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:2004); German version EN ISO 75-1:2004 |
| DIN EN ISO 75-2-2004 | 塑料.载荷下挠曲温度的测定.第2部分:塑料和硬橡胶 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2004); German version EN ISO 75-2:2004 |
| DIN EN ISO 75-3-2004 | 塑料.载荷下挠曲温度的测定.第3部分:高强度热固性叠层板和长纤维增强塑料 | Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:2004); German version EN ISO 75-3:2004 |
| DIN EN ISO 7662-1996 | 橡胶和塑料软管.内衬磨损测定 | Rubber and plastics hoses - Determination of abrasion of lining (ISO 7662:1988); German version EN ISO 7662:1996 |
| DIN EN ISO 7686-2005 | 塑料管和配件.不透明度的测定 | Plastics pipes and fittings - Determination of opacity (ISO 7686:2005); English version of DIN EN ISO 7686 |
| DIN EN ISO 7751-1997 | 橡胶和塑料软管及软管组件.试验压力和爆破压力与设计工作压力的比值 (ISO 7751:1991); 德文版本 EN ISO 775 | Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to design working pressure (ISO 7751:1991); German version EN ISO 7751:1997 |
| DIN EN ISO 7765-1-2004 | 塑料薄膜和薄板.自由落体法测定抗冲击性.第1部分:梯级法 | Plastics film and sheeting - Determination of impact resistance by the free-falling dart method - Part 1: Staircase methods (ISO 7765-1:1988); German version EN ISO 7765-1:2004 |
| DIN EN ISO 7792-1-2004 | 塑料.热塑性聚酯模塑和挤压材料.第1部分:名称与符号系统和基本规范 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 7792-1:1997); German version EN ISO 7792-1:2004 |
| DIN EN ISO 7792-2-2004 | 塑料.热塑性聚酯模塑和挤压材料.第2部分:试验样品的制备和性能测定 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7792-2:1997); German version EN ISO 7792-2:2004 |
| DIN EN ISO 7808-1998 | 塑料.热固性模塑材料.传递流动性的测定 | Plastics - Thermosetting moulding materials - Determination of transfer flow (ISO 7808:1992); German version EN ISO 7808:1998 |
| DIN EN ISO 7822-2000 | 玻璃纤维增强塑料.孔隙率的测定.烧失量、机械粉碎和静态计数法 | Textile glass reinforced plastics - Determination of void content - Loss on ignition, mechanical disintegration and statistical counting methods (ISO 7822:1990); German version EN ISO 7822:1999 |
| DIN EN ISO 7823-1-2003 | 塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和特性.第1部分:浇注薄板材 | Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 1: Cast sheets (ISO 7823-1:2003); German version EN ISO 7823-1:2003 |
| DIN EN ISO 7823-2-2003 | 塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和性能.第2部分:挤制薄板材 | Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 2: Extruded sheets (ISO 7823-2:2003); German version EN ISO 7823-2:2003 |
| DIN EN ISO 7823-3-2007 | 塑料.聚甲基丙烯酸甲酯薄板.类型、尺寸和特征.第3部分:连续浇铸板(ISO 7823-3-2007) | Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 3: Continuous cast sheets (ISO 7823-3:2007); English version of DIN EN ISO 7823-3:2007-08 |
| DIN EN ISO 7854-1997 | 橡胶或塑料涂层织物.抗折曲损坏性测定 | Rubber- or plastics-coated fabrics - Determination of resistance to damage by flexing (ISO 7854:1995); German version EN ISO 7854:1997 |
| DIN EN ISO 8028-2000 | 真空喷漆用橡胶和/或塑料软管组件.规范 | Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO 8028:1999); German version EN ISO 8028:2000 |
| DIN EN ISO 8030-1998 | 橡胶和塑料软管.易燃烧性试验方法 | Rubber and plastics hoses - Method of test for flammability (ISO 8030:1995); German version EN ISO 8030:1997 |
| DIN EN ISO 8032-1999 | 橡胶和塑料软管组件.结合液压脉冲试验的软管弯曲试验(半Ω 型弯曲试验) | Rubber and plastics hose assemblies - Flexing combined with hydraulic impulse test (half-omega test) (ISO 8032:1997); German version EN ISO 8032:1999 |
| DIN EN ISO 8033-2006 | 橡胶和塑料软管.元件间附着力的测定(ISO 8033:2006) | Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2006); English version of DIN EN ISO 8033:2006-11 |
| DIN EN ISO 8256-2005 | 塑料.拉伸冲击强度测定 | Plastics - Determination of tensile-impact strength (ISO 8256:2004); German version EN ISO 8256:2004 |
| DIN EN ISO 8257-1 Berichtigung 1-2006 | 塑料.聚甲基丙烯酸甲酯(PMMA)模塑和挤塑材料.第1部分:命名系统和基本规范(ISO 8257-1:1998) | Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 8257-1:1998); German version EN ISO 8257-1:2006, Corrigenda to DIN EN ISO 8257-1:2006-06 |
| DIN EN ISO 8257-1-2006 | 塑料.聚甲基丙烯酸甲酯(PMMA)模塑和挤塑材料.第1部分:命名体系和基本规范 | Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 8257-1:1998); English version of DIN EN ISO 8257-1:2006-06 |
| DIN EN ISO 8257-2-2006 | 塑料.甲基丙烯酸甲酯(PMMA)模塑和挤塑材料.第2部分:试样制备和性能测定 | Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8257-2:2001); English version of DIN EN ISO 8257-2:2006-06 |
| DIN EN ISO 8295-2004 | 塑料.薄膜和薄板.摩擦系数的测定 | Plastics - Film and sheeting - Determination of the coefficients of friction (ISO 8295:1995); German version EN ISO 8295:2004 |
| DIN EN ISO 8308-2008 | 橡胶和塑料软管和管道.液体通过软管和管道壁传输的测定 | Rubber and plastics hoses and tubing - Determination of transmission of liquids through hose and tubing walls (ISO 8308:2006); German version EN ISO 8308:2008 |
| DIN EN ISO 8330-2010 | 橡胶和塑料软管及软管组件.词汇(ISO 8330-2007);德文版本EN ISO 8330-2008 | Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2007); German version EN ISO 8330:2008 |
| DIN EN ISO 846-1997 | 塑料.微生物作用的评价 | Plastics - Evaluation of the action of microorganisms (ISO 846:1997); German version EN ISO 846:1997 |
| DIN EN ISO 8580-1995 | 橡胶和塑料软管.静定状态下抗紫外线的测定 (ISO 8580:1987); 德文版本 EN ISO 8580:1995 | Rubber and plastics hoses - Determination of ultra-violet resistance under static conditions (ISO 8580:1987); German version EN ISO 8580:1995 |
| DIN EN ISO 8619-2005 | 塑料.酚醛树脂粉.在加热玻璃板上流动距离的测定 | Plastics - Phenolic resin powder - Determination of flow distance on a heated glass plate (ISO 8619:2003); German version EN ISO 8619:2004 |
| DIN EN ISO 868-2003 | 塑料和硬质胶.用硬度计测定针入硬度[肖氏(SHORE)硬度] | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003); German version EN ISO 868:2003 |
| DIN EN ISO 877-1997 | 塑料.自然风化法、窗玻璃后照射法和用夫累内尔镜光照辐射加速风化法 | Plastics - Methods of exposure to direct weathering, to weathering using glass-filtered daylight and to intensified weathering by daylight using Fresnel mirrors (ISO 877:1994); German version EN ISO 877:1996 |
| DIN EN ISO 8795-2001 | 人类生活用水的塑料输水管道系统.偏移评定.塑料管、配件及其接头偏移值测定 | Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints (ISO 8795:2001); German version EN ISO 8795:2001 |
| DIN EN ISO 8974-2002 | 塑料制品.酚醛树脂.采用气相色谱法对残余酚含量的测定 (ISO 8974:2002); 德文版本 EN ISO 8974:2002 | Plastics - Phenolic resins - Determination of residual phenol content by gas chromatography (ISO 8974:2002); German version EN ISO 8974:2002 |
| DIN EN ISO 8985-1998 | 塑料.乙烯/乙烯基乙酸盐共聚物(ENAC)热塑性.乙烯基乙酸盐含量的测定 | Plastics - Ethylene/vinyl acetate copolymer (EVAC) thermoplastics - Determination of vinyl acetate content (ISO 8985:1998); German version EN ISO 8985:1998 |
| DIN EN ISO 8987-2005 | 塑料.酚醛树脂.在B转变试验板上的活化性能的测定 | Plastics - Phenolic resins - Determination of reactivity on a B-transformation test plate (ISO 8987:2005); English version of DIN EN ISO 8987:2005 |
| DIN EN ISO 8988-2006 | 塑料.酚醛树脂.六亚甲基四胺含量测定.基耶达斯法、高氯酸法和氯化氢酸法(ISO 8988-2006) | Plastics - Phenolic resins - Determination of hexamethylenetetramine content - Kjeldahl method, perchloric acid method and hydrochloric acid method (ISO 8988:2006); English version of DIN EN ISO 8988:2006-11 |
| DIN EN ISO 8989-1998 | 塑料.酚醛树脂.水溶物的测定 | Plastics - Phenolic resins - Determination of water miscibility (ISO 8989:1995); German version EN ISO 8989:1998 |
| DIN EN ISO 899-1-2003 | 塑料.蠕变性能的测定.第1部分:拉伸蠕变 | Plastics - Determination of creep behaviour - Part 1: Tensile creep (ISO 899-1:2003); German version EN ISO 899-1:2003 |
| DIN EN ISO 899-2-2003 | 塑料.蠕变性能的测定.第2部分:三点负载时弯曲蠕变 | Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2003); German version EN ISO 899-2:2003 |
| DIN EN ISO 9054-2000 | 硬质泡沫塑料.自结皮高密度材料的试验方法 | Cellular plastics, rigid - Test methods for self-skinned, high-density materials (ISO 9054:1990); German version EN ISO 9054:1999 |
| DIN EN ISO 9080-2003 | 塑料管道和导管系统.用外推法测定热塑性塑料管材的长期静液压强度 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2003); German version EN ISO 9080:2003 |
| DIN EN ISO 9311-2-2002 | 热塑性塑料管道系统用粘合剂.第2部分:剪切强度的测定 (ISO 9311-2:2002); 德文版本 EN ISO 9311-2:2002 | Adhesives for thermoplastic piping systems - Part 2: Determination of shear strength (ISO 9311-2:2002); German version EN ISO 9311-2:2002 |
| DIN EN ISO 9396-2001 | 塑料.酚醛树脂.用自动装置在规定条件下对酚醛树脂胶凝时间的测定 | Plastics - Phenolic resins - Determination of the gel time of resols under specific conditions using automatic apparatus (ISO 9396:1997); German version EN ISO 9396:2000 |
| DIN EN ISO 9702-1998 | 塑料.胺类环氧固化剂.伯仲叔胺基含氮量的测定 | Plastics - Amine epoxide hardeners - Determination of primary, secondary and tertiary amine group nitrogen content (ISO 9702:1996); German version EN ISO 9702:1998 |
| DIN EN ISO 9771-1997 | 塑料.酚醛树脂.酸性条件处理时液体酚醛树脂假绝热温升测定 | Plastics - Phenolic resins - Determination of the pseudo-adiabatic temperature rise of liquid resols when cured under acid conditions (ISO 9771:1995); German version EN ISO 9771:1997 |
| DIN EN ISO 9773-2004 | 塑料.立式软薄试样与小火焰源接触的燃烧性能测定 | Plastics - Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source (ISO 9773:1998 + Amd. 1:2003); German version EN ISO 9773:1998 + A1:2003 |
| DIN EN ISO 9967-2008 | 热塑性塑料管.蠕变比的测定 | Thermoplastics pipes - Determination of creep ratio (ISO 9967:2007); English version of DIN EN ISO 9967:2008-02 |
| DIN EN ISO 9969-2008 | 热塑性塑料管.环压挺度的测定 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2007); English version of DIN EN ISO 9969:2008-03 |
| DIN EN ISO 9988-1-2006 | 塑料.聚甲醛(POM)模塑和挤塑材料.第1部分:命名体系和基本规范 | Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 1 : Designation system and basis for specifications (ISO 9988-1:2004); English version of DIN EN ISO 9988-1:2006-06 |
| DIN ISO 13741-1-2003 | 塑料/橡胶.聚合物分散体和橡胶胶乳(天然的和合成的).用毛细管柱气相色谱法测定残留单体和其他有机成分.第1 | Plastics/rubber - Polymer dispersions and rubber latices (natural and synthetic); Determination of residual monomers and other organic components by capillary-column gas chromatography - Part 1: Direct liquid injection method (ISO 13741-1:1998) |
| DIN ISO 13741-2-2003 | 塑料/橡胶.聚合物分散体和橡胶胶乳(天然的和合成的).用毛细管柱气相色谱法测定残留单体和其他有机成分.第2 | Plastics/rubber - Polymer dispersions and rubber latices (natural and synthetic); Determination of residual monomers and other organic components by capillary-column gas chromatography - Part 2: Headspace method (ISO 13741-2:1998) |
| DIN ISO 1409-2008 | 塑料/橡胶.聚合物含水分散体和橡胶胶乳(天然的和合成的).用环形法测定表面张力 | Plastics/rubber - Polymer dispersions and rubber latices (natural and synthetic) - Determination of surface tension by the ring method (ISO 1409:2006); English version of DIN ISO 1408:2008-11 |
| DIN ISO 15759-2006 | 医用输液设备.用吹-充-封(BFS)法制造的容器用嵌有弹性垫的塑料盖(ISO 15759-2005) | Medical infusion equipment - Plastics caps with inserted elastomeric liner for containers manufactured by the blow-fill-seal (BFS) process (ISO 15759:2005) English version of DIN ISO 15759:2006-05 |
| DIN ISO 171-2000 | 塑料.模塑材料体积系数的测定 | Plastics - Determination of bulk factor of moulding materials (ISO 171:1980) |
| DIN ISO 2115-2001 | 塑料.聚合物分散体.白点温度和最低膜成形温度测定 | Plastics - Polymer dispersions - Determination of white point temperature and minimum film-forming temperature (ISO 2115:1996) |
| DIN ISO 3451-2-1992 | 塑料.灰分的测定.第2部分:聚对苯二甲酸烯烃酯(POLYALKYLENE TEREPHTHALATES)法 | Plastics; determination of ash; polyalkylene terephthalates; identical with ISO 3451-2:1984 |
| DIN ISO 3451-3-1991 | 塑料.灰分的测定.第3部分:未增塑的醋酸纤维素; 等同采用 ISO 3451-3:1984 | Plastics; determination of ash; unplasticized cellulose acetate; identical with ISO 3451-3:1984 |
| DIN ISO 366-4-2006 | 纺织机械和附件.织筘.第4部分:塑料边金属织筘.尺寸和标识 | Textile machinery and accessories - Reeds - Part 4: Plastic bound metal reeds, Dimensions and designations (ISO 366-4:2005);English version of DIN ISO 366-4:2006 |
| DIN ISO 4576-2001 | 塑料.聚合物水分散体.筛余物测定(颗粒总含量和凝固物含量) | Plastics - Polymer dispersions - Determination of sieve residue (gross particle and coagulum content) (ISO 4576:1996) |
| DIN ISO 458-2-1995 | 塑料制品.可弯曲材料的扭曲刚度的测定.第2部分:氯乙烯的均聚物和共聚物的增塑化合物应用 (ISO 458-2:1985) | Plastics - Determination of stiffness in torsion of flexible materials - Part 2: Application to plasticized compounds of homopolymers and copolymers of vinyl chloride (ISO 458-2:1985) |
| DIN ISO 6133-2004 | 橡胶和塑料.测定撕裂强度和粘合强度所获得的多峰图形的分析 | Rubber and plastics - Analysis of multipeak traces obtained in determination of tear strength and adhesion strength (ISO 6133:1998) |
| DIN ISO 7425-1-1990 | 液压传动.弹性体赋能塑料面密封沟槽.尺寸和公差.活塞密封沟槽 | Hydraulic fluid power; housings for elastomer-energized, plastic-faced seals; dimensions and tolerances; piston seal housings; identical with ISO 7425-1:1988 |
| DIN ISO 7425-2-1990 | 液压传动.弹性体赋能塑料面密封沟槽.尺寸和公差.第2部分:活塞杆密封沟槽 | Hydraulic fluid power; housings for elastomer-energized, plastic-faced seals; dimensions and tolerances; rod seal housings; identical with ISO 7425-2:1989 |
| DIN ISO 7765-2-2009 | 塑料薄膜和薄板 用自由落体法测定耐冲击性 第2部分:仪器冲孔试验 | Plastics film and sheeting - Determination of impact resistance by the free-falling dart method - Part 2: Instrumented puncture test (ISO 7765-2:1994); English version of DIN ISO 7765-2:2009-02 |
| DIN ISO 8296-2008 | 塑料.薄膜和薄板.湿润表面张力的测定 | Plastics - Film and sheeting - Determination of wetting tension (ISO 8296:2003);English version of DIN ISO 8296:2008-03 |
| DIN ISO 8362-7-2007 | 注射容器及附件.第7部分:无重叠塑料部件由铝和塑料混合物制造的注射瓶盖 | Injection containers and accessories - Part 7: Injection caps made of aluminium-plastics combinations without overlapping plastics part (ISO 8362-7:2006)；English version of DIN ISO 8362-7:2007-06 |
| DIN ISO 8975-1992 | 塑料.酚醛树脂.pH值的测定 | Plastics; phenolic resins; determination of pH; identical with ISO 8975:1989 |
| DIN ISO 9634-1996 | 航空航天.流体系统.塑料保护帽和保护塞尺寸 (ISO 9634:1994) | Aerospace - Fluid systems - Dimensions of plastic protective caps and plugs (ISO 9634:1994) |
| DIN ISO 976-2008 | 橡胶和塑料.聚合物分散体和橡胶胶乳.pH值的测定 | Rubber and plastics - Polymer dispersions and rubber latices - Determination of pH (ISO 976:1996 + Amd. 1:2006);English version of DIN ISO 976:2008-07 |
| DIN ISO 9944-1992 | 塑料.酚醛树脂.树脂萃取物电导率的测定 | Plastics; phenolic resins; determination of electrical conductivity of resin extracts; identical with ISO 9944:1990 |
| DIN ISO/TS 15874-7-2004 | 冷热水装置用塑料管道设备.聚丙烯(PP).第7部分:合格评定指南 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 7: Guidance for the assessment of conformity (ISO/TS 15874-7:2003); German version CEN ISO/TS 15874-7:2003 |
| DIN ISO/TS 15875-7-2004 | 冷热水装置用塑料管道设备.交联聚乙烯(PE-X).第7部分:合格评定指南 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity (ISO/TS 15875-7:2003); German version CEN ISO/TS 15875-7:2003 |
| DIN ISO/TS 15876-7-2004 | 冷热水装置用塑料管道设备.聚丁烯(PB).第7部分:合格评定指南 | Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 7: Guidance for the assessment of conformity (ISO/TS 15876-7:2003); German version CEN ISO/TS 15876-7:2003 |
| DIN SPEC 1020-2009 | 无压地下排水和污水塑料管道系统.聚乙烯.第2部分:合格评价用指南;德文版本CEN/TS 1852-2-2009 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity; German version CEN/TS 1852-2:2009 |
| DIN SPEC 1030-2010 | 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).第7部分:合格评定指南(ISO/TS 15877-7-2009);德文版本CEN I | Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7:2009); German version CEN ISO/TS 15877-7:2009 |
| DIN V 65380-1987 | 航空航天.纤维加筋塑料.单向叠层板材的试验.与纤维方向平行和横切的压缩试验 | Aerospace; fiber-reinforced plastics; testing of unidirectional laminates; compression test, parallel and transverse to fiber direction |
| DIN V 65900-16-1998 | 航空航天系列.用塑料环自锁的带槽普通六角头螺母的材料 | Aerospace series - Materials for plain, slotted and self-locking by plastic ring hexagonal nuts (AECMA Technical Report TR 3823:1998) |
| DIN V ENV 1046-2002 | 塑料管道系统.输送水或污水用建筑结构外部系统.地上和地下安装惯例 | Plastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for installation above and below ground; German version ENV 1046:2001 |
| DIN V ENV 12108-2001 | 塑料管道系统.建筑物内人用冷热水压力管道安装指南 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption; German version ENV 12108:2001 |
| DIN V ENV 1329-2-2001 | 建筑物内渣土和废物倾倒用塑料管道系统(低和高温).未增塑聚氯乙烯.第2部分:合格评定导则 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity; German version ENV 1329-2:2001 |
| DIN V ENV 13801-2001 | 建筑结构内(低温和高温)渣土和废弃物排放塑料管道系统.热塑管.推荐安装惯例 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation; German version ENV 13801:2001 |
| DIN V ENV 1401-2-2000 | 非压力地下排水和污水管道用塑料管道系统.硬聚氯乙烯(PVC-U).第2部分:一致性评估指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for assessment of conformity; German version ENV 1401-2:2000 |
| DIN V ENV 1401-3-2001 | 无压地下排水和排污塑料管道系统.非增塑聚氯乙烯(PVC-U).第3部分:安装导则 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation; German version ENV 1401-3:2001 |
| DIN V ENV 1451-2-2001 | 建筑物内渣土和废物倾倒用塑料管道系统(低温和高温).聚丙烯.第2部分:合格评定导则 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity; German version ENV 1451-2:2001 |
| DIN V ENV 1452-6-2002 | 供水用塑料管道系统.未增塑聚氯乙烯(PVC-U).第6部分:安装指南: 德文版本 ENV 1452-6:2001 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Guidance for installation; German version ENV 1452-6:2001 |
| DIN V ENV 1452-7-2001 | 供水塑料管道系统.未增塑聚氯乙烯(PVC-U).第7部分:合格评定指南 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 7: Guidance for the assessment of conformity; German version ENV 1452-7:2000 |
| DIN V ENV 1453-2-2001 | 清除建筑物内部尘土和废物(低温和高温)用带结构管壁的塑料管道系统.未增塑聚氯乙烯(PVC-U).第2部分:合格评 | Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity; German version ENV 1453-2:2000 |
| DIN V ENV 1455-2-2001 | 建筑结构中(低温和高温)渣土和废物排放用塑料管道系统.丙烯腈-丁二烯-苯乙烯共聚物(ABS).第2部分:合格评定 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Guidance for the assessment of conformity; German version ENV 1455-2:2001 |
| DIN V ENV 1519-2-2001 | 建筑结构中(低温和高温)渣土和废物排放用塑料管道系统.聚乙烯(PE).第2部分:合格评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity; German version ENV 1519-2:2001 |
| DIN V ENV 1565-2-2001 | 建筑结构中(低温和高温)渣土和废物排放用塑料管道系统.苯乙烯共聚体混合物(SAN+PVC).第2部分:合格评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 2: Guidance for the assessment of conformity; German version ENV 1565-2:2001 |
| DIN V ENV 1566-2-2001 | 建筑结构中(低温和高温)渣土和废物排放用塑料管道系统.氯化聚氯乙烯(PVC-C).第2部分:合格评定指南 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly (vinyl chloride) (PVC-C) - Part 2: Guidance for the assessment of conformity; German version ENV 1566-2:2001 |
| DIN V ENV 1852-2-2000 | 非压力地下排水和污水用塑料管道系统.聚丙烯.第2部分:一致性评估指南 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity; German version ENV 1852-2:2000 |
| DIN V ENV 852-2002 | 生活用水塑料输水管道系统.移位评定.实验室取得的移位值说明指南 | Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Guidance on the interpretation of laboratory derived migration values; German version ENV 852:2001 |
| DIN VDE 0265-1995 | 电力设备塑料绝缘电缆和铅包电缆 | Cables with plastic-insulation and lead-sheath for power installation |
| DIN VDE 0281-1-2003 | 额定电压为450/750V及以下的热塑性塑料绝缘电缆.第1部分:一般要求 | Cables of rated voltages up to and including 450/750 V and having thermoplastic insulation - Part 1: General requirements; German version HD 21.1 S4:2002 |
| DIN-Fachbericht CEN/TR 15353-2007 | 塑料.再生塑料.与再生塑料相关标准研发指南 | Plastics - Recycled plastics - Guidelines for the development of standards relating for recycled plastics; German version CEN/TR 15353:2007 |
| DIN-Fachbericht CEN/TR 15438-2007 | 塑料管.产品编码及其使用指南 | Plastics piping systems - Guidance for coding of products and their intended uses; German version CEN/TR 15438 |
| DIN-Fachbericht CEN/TR 15591-2007 | 固体再生材料.塑料制品.基于C-14法测定生物的数量 | Solid recovered fuels - Determination of the biomass content based on the C method; German version CEN/TR 15591:2007 |
| 编号 | 中文名称 | 英文名称 |