| 编号 | 中文名称 | 英文名称 |
|---|
| ANSI PH3.58-1974
| 摄影用大功率立方闪光灯(电池控制)的尺寸
| Dimensions for Photographic High-Power Cubes (Battery Operated)
|
| ANSI PH7.3-1977
| 用于演讲的教学视听设备的有效输出功率频带宽度的测量方法
| Method for Measuring Effective Output Power Bandwidth for Institutional Audio-Visual Equipment Used Primarily for Speech
|
| ANSI S12.12-1992
| 根据声音强度测定噪声源声功率级的工程方法
| Engineering method for the determination of sound power levels of noise sources using sound intensity
|
| ANSI S12.23-1989
| 机械和设备发出的声功率的表示方法
| Method for the Designation of Sound Power Emitted by Machinery and Equipment
|
| ANSI S12.30-1990
| 声功率标准的使用导则和噪声试验规程的制定导则
| Guidelines for the use of sound power standards and for the preparation of noise test codes
|
| ANSI S12.50-2002
| 声学.噪声源的声功率级的测定.基本标准使用指南
| Acoustics - Determination of sound power levels of noise sources - Guidelines for the use of basic standards
|
| ANSI S12.53/1-1999
| 声学.测定噪声源的声功率级.混响场内小型可移动声源的工程法.第1部分:硬壁试验室中的比较法
| Acoustics - Determination of Sound Power Levels of Noise Sources - Engineering Methods for Small, Movable Sources in Reverberant Fields - Part 1: Comparison Method for Hard-Walled Test Rooms
|
| ANSI S12.53/2-1999
| 声学.测定噪声源的声功率级.混响声场内小型可移动声源的工程法.第2部分:专用混响试验室法
| Acoustics - Determination of Sound Power Levels of Noise Sources - Engineering Methods for Small, Movable Sources in Reverberant Fields - Part 2: Methods for Special Reverberation Test Rooms
|
| ANSI S12.54-1999
| 声学.声压法测定噪声源的声功率级.反射面上近似自由场的工程法
| Acoustics - Determination of Sound Power Levels of Noise Sources using Sound Pressure - Engineering Method in an Essentially Free Field over a Reflecting Plane
|
| ANSI S12.56-1999
| 声学.声压法测定噪声源声功率级.反射面上包络测量表面的测量方法
| Acoustics - Determination of Sound Power Levels of Noise Sources using Sound Pressure - Survey Method using an Enveloping Measurement Surface over a Reflecting Plane
|
| ANSI S12.57-2002
| 声学.声压法测定声源的声功率级.现场比较法
| Acoustics - Determination of sound power levels of noise sources using sound pressure - Comparison method in situ
|
| ANSI T1.337-2004
| 网络电力传输系统的最大电压、电流和功率级的要求
| Requirements for Maximum Voltage, Current, and Power Levels in Network-Powered Transport System
|
| ANSI/AGMA 6035-2002
| 工业球面蜗杆传动机构的设计、额定功率和用途
| Design, Rating and Application of Industrial Globoidal Wormgearing
|
| ANSI/AGMA 6135-2002
| 工业球面蜗杆传动机构的设计、额定功率和用途(米制版本)
| Design, Rating and Application of Industrial Globoidal Wormgearing (Metric Edition)
|
| ANSI/ANS 5.1-2005
| 轻水反应堆衰变热功率
| Light Water Reactors, Decay Heat Power in
|
| ANSI/ASHRAE 68-1997
| 风扇风道内测试声功率测量程序的实验室方法
| Laboratory Method of Testing In-Duct Sound Power Measurement Procedure for Fans (also designated ANSI/AMCA 330-86)
|
| ANSI/ASTM D6201-2004
| 进油阀沉积物形成用无铅火花点火发动机燃料的功率计评价用试验方法
| Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Value Deposit Formation
|
| ANSI/CAGI ADF300-1998
| 干塔（非回热式）脱水压缩空气干燥器.额定功率和试验方法
| Single Tower (Non-Regenerative) Desiccant Compressed Air Dryers - Methods for Testing and Rating
|
| ANSI/CAGI ADF700-1998
| 膜式压缩空气干燥器.额定功率和试验方法
| Membrane Compressed Air Dryers - Methods for Testing and Rating
|
| ANSI/CEA 426-B-1998
| 全频带扬声器功率额定值
| Loudspeakers, Power Rating, Full Range
|
| ANSI/EIA 401-1973
| 功率半导体设备用纸介质和纸/薄膜介质电容器
| Paper, Paper/Film Dielectric Capacitors for Power Semiconductor Applications
|
| ANSI/EIA 426-B-1998
| 全频程额定功率的扬声器
| Loudspeakers, Power Rating, Full Range
|
| ANSI/EIA 526-2-1989
| 接入单模光缆的OFSTP-2发送器有效输出功率
| OFSTP-2, Effective Transmitter Output Power Coupled into Single-Mode Fiber Optic Cable
|
| ANSI/EIA 700BAAD-2000
| 通用系列总线加功率连接器系列"A"用屏蔽矩形连接器的详细规范
| Detail Specification for Shielded Rectangular Connectors for Universal Serial Bus Plus Power Connectors Series "A"
|
| ANSI/EIA 700BAAE-2000
| 通用系列总线加功率连接器系列"B"用屏蔽矩形连接器的详细规范
| Detail Specification for Shielded Rectangular Connectors for Universal Serial Bus Plus Power Connectors Series"B"
|
| ANSI/EIA-700BAAD-2000
| 通用系列总线插头功率连接器系列"A"用屏蔽矩形连接器的详细规范
| Detail Specification for Shielded Rectangular Connectors for Universal Serial Bus Plus Power Connectors Series "A"
|
| ANSI/EIA-700BAAE-2000
| 通用系列总线插头功率连接器系列"B"用屏蔽矩形连接器的详细规范
| Detail Specification for Shielded Rectangular Connectors for Universal Serial Bus Plus Power Connectors Series"B"
|
| ANSI/IEC/ASQ D1123-1997
| 可靠性试验.符合性试验计划的成功率
| Reliability Testing - Compliance Test Plans for Success Ratio
|
| ANSI/IEEE 1573-2003
| 电子大功率子系统的推荐规程:参数、接口、元件和性能
| Recommended Practice for Electronic Power Subsystems: Parameters, Interfaces, Elements, and Performance
|
| ANSI/IEEE 388-1992
| 电子功率变换设备中的变压器和感应线圈
| Transformers and Inductors in Electronic Power Conversion Equipment
|
| ANSI/IEEE 664-1994
| 单根导线风吹震动阻尼器功率耗散特性的实验室测量
| Laboratory Measurement of the Power Dissipation Characteristics of Aeolian Vibration Dampers for Single Conductors
|
| ANSI/IEEE 802.11h-2003
| 信息技术标准.系统间远程通信和信息交换.局域网和城域网.特殊要求.第11部分:无线局域网媒体访问控制(MAC)和
| Standard [for] Information Technology - Telecommunications and Information Exchange Between Systems - Local and Metropolitan Networks - Specific Requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications - Spectrum and Transmit Power Management Extensions in the 5 GHz Band in Europe
|
| ANSI/IEEE 841-2001
| 化学工业.功率达500hp及以下的全封闭扇冷却式重载(TEFC)鼠笼式感应电动机
| Chemical Industry - Severe Duty Totally Enclosed Fan-Cooled (TEFC) Squirrel Cage Induction Motors - Up to and Including 500 hp
|
| ANSI/IEEE C37.26-2003
| 低压感应测试电路功率因数的测量方法
| Methods of Power-Factor-Measurement for Low-Voltage Inductive Test Circuits
|
| ANSI/IEEE C57.136-2000
| 额定功率大于500kVA的油浸式电力变压器和并联电抗器的声级抑制和测定指南
| Guide for Sound Level Abatement & Determination for Liquid-Immersed Power Transformers & Shunt Reactors Rated Over 500 kVA
|
| ANSI/INCITS/ISO/IEC 14443-2AMD 1-2005
| 识别卡.无接触点集成电路卡.近似卡.第2部分:射频功率和信号.修改1:fc/64, fc/32 and fc/16毕特速率
| Identification cards - Contactless integrated circuit(s) cards - Proximity cards - Part 2: Radio frequency power and signal interface - Amendment 1: Bit rates of fc/64, fc/32 and fc/16
|
| ANSI/ISO 3743-2-1994
| 声学.声压法测定噪声源声功率级.混响声场中小型可移动声源的工程检测法.第2部分:专用混响试验室法
| Acoustics - Determination of Sound Power Levels of Noise Sources - Engineering Methods for Small, Movable Sources in Reverberant Fields - Part 2: Methods for Special Reverberation Test Rooms
|
| ANSI/ISO 3744-1994
| 声学.声压法测定噪声源声功率级.声音反射平面上近似自由场中的工程检测法
| Acoustics - Determination of Sound Power Levels of Noise Sources using Sound Pressure - Engineering Method in an Essentially Free Field over a Reflecting Plane
|
| ANSI/ISO 3746-1995
| 声学.声压法测定噪声源声功率级.对声音反射平面进行曲面包络线测量方法
| Acoustics - Determination of Sound Power Levels of Noise Sources using Sound Pressure - Survey Method using an Enveloping Measurement Surface over a Reflecting Plane
|
| ANSI/NEMA C119.1-2006
| 额定功率600V 的密封绝缘地下连接器系统
| Sealed Insulated Underground Connector System Rated 600 Volts
|
| ANSI/NEMA WC53-2000
| 试验用挤压介电功率、控制、仪器仪表和轻便电缆的标准试验方法
| Standard Test Methods for Extruded Dielectric Power, Control, Instrumentation, and Portable Cables for Test
|
| ANSI/NFPA 1127-2002
| 大功率火箭
| High Power Rocketry
|
| ANSI/NSF 8(i4r2)-2002
| 大功率食品加工设备
| Comercial Powered Food Preparation Equipment
|
| ANSI/SAE J1343-1981
| 关于卡车和公共汽车发动机附件的负载循环和平均功率要求的信息
| Truck and Bus Engine Accessories, Information Relating to Duty Cycles and Average Power Requirements of
|
| ANSI/SAE J2458-1998
| 排气闸功率计试验和能力评级程序
| Exhaust Brake Dynamometer Test and Capability Rating Procedure
|
| ANSI/SAE J721-1993
| 拖拉机和功率输出传动的农机具的操纵要求
| Operating Requirements for Tractors and Power Take-Off Driven Implements
|
| ANSI/SAE J820-1998
| 起重机提升线速度和功率试验规程
| Crane Hoist Line Speed and Power Test Code
|
| ANSI/TIA-455-208-2000
| FOTP208.IEC 61290-1-3.光纤放大器.基础规范.第1-3部分:增益参数的测试方法.光功率计
| FOTP208- IEC 61290-1-3 - Optical Fibre Amplifiers - Basic Specification - Part 1-3: Test Methods for Gain Parameters - Optical Power Meter
|
| ANSI/TIA-455-209-2000
| FOTP209.IEC 61290-2-1.光纤放大器.基础规范.第2-1部分:光功率参数的测试方法.光谱分析仪
| FOTP209 - IEC 61290-2-1 - Optical Fibre Amplifiers - Basic Specification Part 2-1: Test Methods for Optical Power Parameters - Optical Spectrum Analyzer
|
| ANSI/TIA-455-210-2000
| FOTP209.IEC 61290-2-1.光纤放大器.基础规范.第2-2部分:光功率参数的测试方法.电频谱分析仪
| FOTP210-IEC 61290-2-2 - Optical Fibre Amplifiers - Basic Specification - Part 2-2: Test Methods for Optical Power Parameters - Electrical Spectrum Analyzer
|
| ANSI/TIA-455-211-2000
| FOTP211.IEC 61290-2-3.光纤放大器.基础规范.第2-3部分:光功率参数的测量方法.光功率计多路分解器
| FOTP211 - IEC 61290-2-3- Optical Fibre Amplifiers - Basic Specification - Part 2-3: Test Methods for Optical Power Parameters - Optical Power Meter demultiplexer
|
| ANSI/TIA-455-213-2000
| FOTP213.IEC 61290-7-1.光纤放大器.基础规范.第7-1部分:频带外插入损耗的测试方法.滤光光学功率计
| FOTP213 - IEC 61290-7-1 - Optical Fibre Amplifiers -Basic Specification - Part 7-1: Test Methods for Out-of-Band Insertion Losses - Filtered Optical Power Meter
|
| ANSI/TIA-455-231-2003
| IEC 61315.纤维光学功率计的校准
| IEC 61315 - Calibration of Fibre-Optic Power Meters
|
| ANSI/TIA-455-80-C-2003
| 用传输功率测量未用电缆固定的单模光纤的截止波长
| Measuring Cutoff Wavelength of Uncabled Single-Mode Fiber by Transmitted Power
|
| ANSI/TIA-455-95A-2000
| 光纤和光缆的绝对光功率试验
| Absolute Optical Power Test for Optical Fibers and Cables
|
| ANSI/TIA/EIA 455-208-2000
| FOTP208-IEC 61290-1-3-光纤放大器. 基本规范 .第1-3部分: 增益参数测试方法.光功率计
| FOTP208- IEC 61290-1-3 - Optical Fibre Amplifiers - Basic Specification - Part 1-3: Test Methods for Gain Parameters - Optical Power Meter
|
| ANSI/TIA/EIA 455-209-2000
| FOTP209-IEC 61290-2-1-光纤放大器. 基本规范 .第2-1部分: 光功率参数测试方法.光频谱分析仪
| FOTP209 - IEC 61290-2-1 - Optical Fibre Amplifiers - Basic Specification Part 2-1: Test Methods for Optical Power Parameters - Optical Spectrum Analyzer
|
| ANSI/TIA/EIA 455-210-2000
| FOTP210-IEC 61290-2-2-光纤放大器. 基本规范 .第2-2部分: 光功率参数测试方法.电频谱分析仪
| FOTP210-IEC 61290-2-2 - Optical Fibre Amplifiers - Basic Specification - Part 2-2: Test Methods for Optical Power Parameters - Electrical Spectrum Analyzer
|
| ANSI/TIA/EIA 455-211-2000
| FOTP211-IEC 61290-2-3-光纤放大器. 基本规范.第2-3部分: 光功率参数测试方法.光功率计多路分配器
| FOTP211 - IEC 61290-2-3- Optical Fibre Amplifiers - Basic Specification - Part 2-3: Test Methods for Optical Power Parameters - Optical Power Meter demultiplexer
|
| ANSI/TIA/EIA 455-213-2000
| FOTP213-IEC 61290-7-1-光纤放大器. 基本规范.第7-1部分:频带外插入损耗的测试方法.滤波光功率计
| FOTP213 - IEC 61290-7-1 - Optical Fibre Amplifiers -Basic Specification - Part 7-1: Test Methods for Out-of-Band Insertion Losses - Filtered Optical Power Meter
|
| ANSI/TIA/EIA 455-80-C-2003
| 用传输功率测量未敷设的单模光纤电缆的截止波长
| Measuring Cutoff Wavelength of Uncabled Single-Mode Fiber by Transmitted Power
|
| ANSI/TIA/EIA 455-80B-1998
| 用传输功率测量散单模纤维的截止波长
| Measuring Cutoff Wavelength of Uncabled Single-Mode Fiber by Transmitted Power
|
| ANSI/TIA/EIA 455-95A-2000
| 光纤和电缆绝对光功率试验
| Absolute Optical Power Test for Optical Fibers and Cables
|
| ANSI/UL 13-2005
| 有功率限制的电路电缆的安全标准
| Standard for Safety for Power-Limited Circuit Cables
|
| ANSI/UL 1424-2005
| 有限功率火灾报警线路用电缆的安全标准
| Standard for Safety for Cables for Power-Limited Fire-Alarm Circuits
|
| ANSI/UL 508C-2005
| 功率转换设备的安全性标准
| Standard for Safety for Power Conversion Equipment
|
| ASME 3977-2-2000
| 燃气轮机.采购.第2部分:标准参考条件和额定功率
| (Gas turbines - Procurement - Part 2: Standard reference conditions and ratings) |
| ASME PTC 19.8-1970
| 装置和仪器.第8部分:指示功率测量
| (Instruments and apparatus - Part 8: Measurement of indicated power)
|
| ASTM B 77-1981
| 电阻合金的热电功率的测试方法
| Test Method for Thermoelectric Power of Electrical-Resistance Alloys
|
| ASTM D 2758-1994
| 使用发动机功率计测试发动机冷却剂的标准试验方法
| Standard Test Method for Engine Coolants by Engine Dynamometer
|
| ASTM D 4336-2005
| 测定机械泵计量器每行程输出功率的标准试验方法
| Standard Test Methods for Determination of the Output Per Stroke of a Mechanical Pump Dispenser
|
| ASTM D 6201-2004
| 进油阀沉积物形成用火花点燃式发动机无铅燃料的功率计评定标准试验方法
| Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
|
| ASTM D 924-2004
| 电绝缘液体的损耗因数(或功率因数)和相对电容率(介电常数)的标准试验方法
| Standard Test Method for Dissipation Factor (or Power Factor) and Relative Permittivity (Dielectric Constant) of Electrical Insulating Liquids
|
| ASTM E 1124-1997
| 用双面法现场测量声功率级的标准试验方法
| Standard Test Method for Field Measurement of Sound Power Level by the Two-Surface Method
|
| ASTM E 387-2004
| 用不透明滤光器评估色散分光光度计杂散辐射功率的标准试验方法
| Standard Test Method for Estimating Stray Radiant Power Ratio of Dispersive Spectrophotometers by the Opaque Filter Method
|
| ASTM F 1334-2002
| 测定真空吸尘器A-加重声音功率级的标准试验方法
| Standard Test Method for Determining A-Weighted Sound Power Level of Vacuum Cleaners
|
| ASTM F 466-1979
| 在0.2至2.0千兆赫频率范围内小功率晶体管的小信号散射参数的试验方法
| Test Method for Small-Signal Scattering Parameters of Low-Power Transistors in the 0.2 to 2.0-GHz Frequency Range
|
| IEEE 1158-1991
| 高压直流变电站功率损失测定用推荐规范
| (Recommended practice for determination of power losses in high-voltage direct current (HVDC) converter stations)
|
| IEEE 1481-1999
| 集成电路(IC)延迟和功率计算系统
| (Integrated Circuit (IC) delay and power calculation system)
|
| IEEE 1515-2000
| 电子大功率子系统的推荐规程:参数定义、试验条件和方法
| (Recommended practice for electronic power subsystems: Parameter definitions, test conditions, and test methods)
|
| IEEE 286-2000
| 电机定子线圈绝缘的功率因数tip-up测量的推荐实施规程
| (Recommended practice for measurement of power factor tip-up of electric machinery stator coil insulation)
|
| IEEE 388-1992
| 电子功率转换设备中的变压器和电感线圈
| (Transformers and inductors in electronic power conversion equipment)
|
| IEEE 510-1983
| 高电压及高功率安全性推荐规程
| (Recommended practices for safety in high-voltage and high-power testing)
|
| IEEE C 37.26-1972
| 低电压电感试验电路功率因数的测量方法指南
| (Guide for methods of power-factor measurement for low-voltage inductive test circuits)
|
| IEEE C 57.136-2000
| 额定功率大于500kVA的液浸式电力变压器和并联电抗器的声级抑制和测定
| (Sound level abatement and determination for liquid-immersed power transformers and shunt reactors rated over 500 kVA)
|
| UL 13-1996
| 有功率限制的电路电缆
| (Power-limited circuit cables )
|
| 编号 | 中文名称 | 英文名称 |
|---|