| 编号 | 中文名称 | 英文名称 |
|---|
| ISO 10645-1992
| 核能 轻水反应堆 核燃料衰变热功率的计算
| Nuclear energy; light water reactors; calculation of the decay heat power in nuclear fuels
|
| ISO 10816-2 Technical Corrigendum 1-2004
| 机械振动.通过在非旋转部件上的测量评价机械振动.第2部分:超过50MW功率的标准操作速度为1500 r/min、1800 r
| Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1500 r/min, 1800 r/min, 3000 r/min and 3600 r/min; Technical Corrigendum 1
|
| ISO 10816-2-2001
| 机械振动 用非旋转部件上的测量评定机器振动 第2部分：功率超过50MW、额定转速在1500r/min、1800r/min、3
| Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1500 r/min, 1800 r/min, 3000 r/min and 3600 r/min
|
| ISO 10816-3-1998
| 机械振动 在非旋转部件上测量和评定机器振动 第3部分:在额定功率大于15kW、额定转速在120 r/min和15000 r/m
| Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 3: Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15000 r/min when measured in situ
|
| ISO 10816-6-1995
| 机械振动 在非旋转部件上测量和评定机械振动 第6部分:额定功率在100KW以上的往复式机器
| Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 6: Reciprocating machines with power ratings above 100 kW
|
| ISO 11157-2005
| 道路车辆.制动衬片组件.惯性功率计试验方法
| Road vehicles - Brake lining assemblies - Inertia dynamometer test method
|
| ISO 11203-1995
| 声学 机器和设备发射的噪声 从声功率级测定工作位置和其他指定位置发射声压级
| Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level
|
| ISO 11554-2006
| 光学和光子学.激光和激光设备.激光束功率、能量和时间特征的试验方法
| Optics and photonics - Lasers and laser-related equipment - Test methods for laser beam power, energy and temporal characteristics
|
| ISO 11592-2001
| 艇身长度小于 8m 的小型船 最大驱动功率额定值的测定
| Small craft less than 8 m length of hull - Determination of maximum propulsion power rating
|
| ISO 13253-1995
| 管道式空调器和气-气加热泵 性能的检测和额定功率
| Ducted air-conditioners and air-to-air heat pumps - Testing and rating for performance
|
| ISO 13256-1-1998
| 水源热泵 性能试验和额定功率 第1部分:水-气和盐水-气热泵
| Water-source heat pumps - Testing and rating for performance - Part 1: Water-to-air and brine-to-air heat pumps
|
| ISO 13256-2-1998
| 水源热泵 性能试验和额定功率 第2部分:水-水和盐水-水热泵
| Water-source heat pumps - Testing and rating for performance - Part 2: Water-to-water and brine-to-water heat pumps
|
| ISO 13261-1-1998
| 空调和空气源热泵设备的声功率额定值 第1部分:无室外管道设备
| Sound power rating of air-conditioning and air-source heat pump equipment - Part 1: Non-ducted outdoor equipment
|
| ISO 13261-2-1998
| 空调和空气源热泵设备的声功率额定值 第2部分:无室内管道设备
| Sound power rating of air-conditioning and air-source heat pump equipment - Part 2: Non-ducted indoor equipment
|
| ISO 13347-1-2004
| 工业风扇.标准化实验室条件下风扇声功率级的测定.第1部分:总揽
| Industrial fans - Determination of fan sound power levels under standardized laboratory conditions - Part 1: General overview
|
| ISO 13347-2-2004
| 工业风扇.标准化实验室条件下风扇声功率级的测定.第2部分:混响室法
| Industrial fans - Determination of fan sound power levels under standardized laboratory conditions - Part 2: Reverberant room method
|
| ISO 13347-3-2004
| 工业风扇.标准化实验室条件下风扇声功率级的测定.第3部分:包络面法
| Industrial fans - Determination of fan sound power levels under standardized laboratory conditions - Part 3: Enveloping surface methods
|
| ISO 13347-4-2004
| 工业风扇.标准化实验室条件下风扇声功率级的测定.第4部分:声强法
| Industrial fans - Determination of fan sound power levels under standardized laboratory conditions - Part 4: Sound intensity method
|
| ISO 14396-2002
| 往复式内燃机.发动机功率的测量和检测方法.依据ISO 8178的废气排放试验的补充要求
| Reciprocating internal combustion engines - Determination and method for the measurement of engine power - Additional requirements for exhaust emission tests in accordance with ISO 8178
|
| ISO 15550-2002
| 内燃机.发动机功率的测量和检测方法.一般要求
| Internal combustion engines - Determination and method for the measurement of engine power - General requirements
|
| ISO 1585-1992
| 道路车辆 发动机试验规程 净功率
| Road vehicles; engine test code; net power
|
| ISO 16902-1-2003
| 液压传动.用声强法测定声功率级的试验规程:工程法.第1部分:泵
| Hydraulic fluid power - Test code for the determination of sound power levels using sound intensity techniques: Engineering method - Part 1: Pumps
|
| ISO 2534-1998
| 道路车辆 发动机试验规程 总功率
| Road vehicles - Engine test code - Gross power
|
| ISO 3002-4-1984
| 切削和磨削加工的基本参数 第4部分:力、能量和功率
| Basic quantities in cutting and grinding; Part 4 : Forces, energy, power
|
| ISO 3046-1-2002
| 往复式内燃机.性能.第1部分:功率、燃料消耗量和润滑油消耗量和试验方法说明.通用内燃机的附加要求
| Reciprocating internal combustion engines - Performance - Part 1: Declarations of power, fuel and lubricating oil consumptions, and test methods; Additional requirements for engines for general use
|
| ISO 3740-2000
| 声学 噪声源声功率级的测定 基本标准使用导则
| Acoustics - Determination of sound power levels of noise sources - Guidelines for the use basic standards
|
| ISO 3741 Technical Corrigendum 1-2001
| 声学 声压法测定噪声源声功率级 混响室精密法 技术勘误1
| Acoustics - Determination of sound power levels of noise sources using sound pressure - Precision methods for reverberation rooms; Technical Corrigendum 1
|
| ISO 3741-1999
| 声学 声压法测定噪声源声功率级 混响室精密法
| Acoustics - Determination of sound power levels of noise sources using sound pressure - Precision methods for reverberation rooms
|
| ISO 3743-1-1994
| 声学 噪声源声功率级的测定 混响声场中小型可移动声源的工程法 第1部分:硬壁试验室中的比较法
| Acoustics; determination of sound power levels of noise sources; engineering methods for small, movable sources in reverberant fields; part 1: comparison method in hard-walled test rooms
|
| ISO 3743-2-1994
| 声学 声压法测定噪声源声功率级 混响声场中小型可移动声源的工程法 第2部分:专用混响试验室法
| Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms
|
| ISO 3744-1994
| 声学 声压法测定噪声源声功率级 一个反射面上方近似自由场中的工程法
| Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering method in an essentially free field over a reflecting plane
|
| ISO 3745-2003
| 声学.用声压法测定噪声源声功率级.消声室和半消声室精密法
| Acoustics - Determination of sound power levels of noise sources using sound pressure - Precision methods for anechoic and hemi-anechoic rooms
|
| ISO 3746 Technical Corrigendum 1-1995
| 声学 声压法测定噪声源声功率级 采用包络测量面的简易法 技术勘误1
| Acoustics - Determination of sound power levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane; Technical Corrigendum 1
|
| ISO 3746-1995
| 声学 声压法测定噪声源声功率级 采用包络测量面的简易法
| Acoustics - Determination of sound power levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane
|
| ISO 3747-2000
| 声学 声压法测定噪声源声功率级 现场比较法
| Acoustics - Determination of sound power levels of noise sources using sound pressure - Comparison method in situ
|
| ISO 4106-2004
| 摩托车.发动机试验规程.净功率
| Motorcycles - Engine test code - Net power
|
| ISO 4164-1978
| 道路车辆 轻便摩托车 发动机试验规程 净功率
| Road vehicles; Mopeds; Engine test code; Net power
|
| ISO 5048-1989
| 连续搬运设备 带承载托辊的带式输送机 运行功率和张力的计算
| Continuous mechanical handling equipment; belt conveyors with carrying idlers; calculation of operating power and tensile forces
|
| ISO 5135-1997
| 声学 在混响室中测定空调终端设备、空调终端单元、阻尼器和调节阀门的噪声功率级
| Acoustics - Determination of sound power levels of noise from air-terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room
|
| ISO 5136-2003
| 声学.风机和其他风动设备辐射入管道中的声功率的测定.管道法
| Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method
|
| ISO 5292-1995
| 带传动 V带和多楔带 额定功率的计算
| Belt drives - V-belts and V-ribbed belts - Calculation of power ratings
|
| ISO 5295-1987
| 同步带 额定功率和传动中心距的计算
| Synchronous belts; Calculation of power rating and drive centre distance
|
| ISO 6185-1-2001
| 充气艇 第1部分：最大发动功率额定值为4.5KW的艇
| Inflatable boats - Part 1: Boats with a maximum motor power rating of 4,5 kW
|
| ISO 6185-2-2001
| 充气艇 第2部分：最大发动功率额定值为4.5KW-15KW（含15KW）的艇
| Inflatable boats - Part 2: Boats with a maximum motor power rating of 4,5 kW to 15 kW inclusive
|
| ISO 6185-3-2001
| 充气艇 第3部分：最大发动功率额定值为大于等于15KW的艇
| Inflatable boats - Part 3: Boats with a maximum motor power rating of 15 kW and greater
|
| ISO 6926-1999
| 声学 声功率级测定用的基准声源的性能和校正的要求
| Acoustics - Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels
|
| ISO 7119-1981
| 松散物料连续搬运设备 螺旋输送机 驱动功率设计规则
| Continuous mechanical handling equipment for loose bulk materials; Screw conveyors; Design rules for drive power
|
| ISO 789-1-1990
| 农业拖拉机 试验程序 第1部分:输出功率试验
| Agricultural tractors; test procedures; part 1: power tests for power take-off
|
| ISO 789-5-1983
| 农业拖拉机 试验程序 第5部分:动力输出端(PTO) 非机械传输功率
| Agricultural tractors; Test procedures; Part 5 : Partial power PTO; Non-mechanically transmitted power
|
| ISO 789-7-1991
| 农业拖拉机 试验程序 第7部分:轴功率测定
| Agricultural tractors; test procedures; part 7: axle power determination
|
| ISO 789-9 AMD 1-1993
| 农业拖拉机 试验程序 第9部分:牵引功率试验 修改1
| Agricultural tractors; test procedures; part 9: power tests for drawbar; amendment 1
|
| ISO 789-9-1990
| 农业拖拉机 试验程序 第9部分:牵引功率试验
| Agricultural tractors; test procedures; part 9: power tests for drawbar
|
| ISO 7919-2-2001
| 机械振动 用旋转轴的测量评定机械振动 第2部分：功率超过50MW、额定转速在1500r/min、1800 r/min、3000 r
| Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1500 r/min, 1800 r/min, 3000 r/min and 3600 r/min
|
| ISO 8297-1994
| 声学 为评定环境测定多声源工业厂房的声功率级 工程法
| Acoustics - Determination of sound power levels of multisource industrial plants for evaluation of sound pressure levels in the environment - Engineering method
|
| ISO 8528-8-1995
| 往复式内燃交流发电机组 第8部分:小功率发电机组技术要求和试验
| Reciprocating internal combustion engine driven alternating current generating sets - Part 8: Requirements and tests for low-power generating sets
|
| ISO 8759-1-1998
| 农业轮式拖拉机 前悬装置 第1部分:功率输出和三点悬挂装置
| Agricultural wheeled tractors - Front-mounted equipment - Part 1: Power take-off and three-point linkage
|
| ISO 9249 Technical Corrigendum 1-1999
| 土方机械 发动机的试验规程 净功率 技术勘误1
| Earth-moving machinery - Engine test code - Net power; Technical Corrigendum 1
|
| ISO 9249-1997
| 土方机械 发动机的试验规程 净功率
| Earth-moving machinery - Engine test code - Net power
|
| ISO 9614-1-1993
| 声学 声强法测定噪声源声功率级 第1部分:离散点测量法
| Acoustics; determination of sound power levels of noise sources using sound intensity; part 1: measurement at discrete points
|
| ISO 9614-2-1996
| 声学 声强法测定噪声源声功率级 第2部分:扫描测量法
| Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 2: Measurement by scanning
|
| ISO 9614-3-2002
| 声学.利用声音强度测定噪声源功率级.第3部分:扫描测量精度法
| Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 3: Precision method for measurements by scanning
|
| ISO 9775-1990
| 小艇 功率15kW～40kW舷外挂机的遥控操作系统
| Small craft - Remote steering systems for single outboard motors of 15 kW to 40 kW power
|
| ISO/IEC 14443-2 AMD 1-2005
| 识别卡.无触点集成电路卡.近程卡.第2部分:射频功率和信号接口.修改件1:fc/64, fc/32和fc/16的位率
| Identification cards - Contactless integrated circuit(s) cards; Proximity cards - Part 2: Radio frequency power and signal interface; Amendment 1: Bit rates of fc/64, fc/32 and fc/16
|
| ISO/IEC 14443-2-2001
| 识别卡 无接触点集成电路卡 近程卡 第2部分：无线电频率功率和信号接口
| Identification cards - Contactless integrated circuit(s) cards; Proximity cards - Part 2: Radio frequency power and signal interface
|
| ISO/OECD 789-10-2006
| 农业拖拉机.试验程序.第10部分:拖拉机与农具连接界面液压功率
| Agricultural tractors - Test procedures - Part 10: Hydraulic power at tractor/implement interface |
| 编号 | 中文名称 | 英文名称 |
|---|