| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| EN 1013-2-1998 | 单层顶盖用透光齿形塑料板 第2部分：玻璃纤维增强的聚脂树脂薄板的特殊要求和试验方法 | Light transmitting profiled plastic sheeting for single skin roofing - Part 2: Specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP) |
| EN 10289-2002 | 岸上和海上管路钢管及配件 加有环氧树脂和改性环氧树脂胶的外用液体 | Steel tubes and fittings for onshore and offshore pipelines - External liquid applied epoxy and epoxy-modified coatings |
| EN 1115-1-1997 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第1部分：概述 | Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 1: General |
| EN 1115-3-1996 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第3部分：配件 | Plastics piping systems for underground drainage and sewerage under pressure - Glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings |
| EN 1115-5-1996 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第5部分：连接 | Plastics piping systems for underground drainage and sewerage under pressure - Glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints |
| EN 12003-1997 | 瓷砖粘合剂 树脂粘合剂应力的剪切粘接强度的测定 | Adhesives for tiles - Determination of shear adhesion strength of reaction resin adhesives |
| EN 12808-1-1999 | 瓷砖用粘合剂和灰浆 第1部分：反应树脂砂浆耐化学腐蚀性测定 | Adhesives and grouts for tiles - Part 1: Determination of chemical resistance of reaction resin mortars |
| EN 13366-2001 | 肥料 测定螯合微营养物含量和微营养物螯合部分的阳离子交换树脂处理法 | Fertilizers - Treatment with a cation exchange resin for the determination of the chelated micro-nutrient content and of the chelated fraction of micro-nutrients |
| EN 13411-4-2002 | 钢丝绳终端设备 安全性 第4部分：金属和树脂套座 | Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing |
| EN 1636-3-1997 | 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第3部分：管件 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings |
| EN 1636-5-1997 | 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第5部分：针对接头 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints |
| EN 1636-6-1997 | 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第6部分：安装实践 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 6: Practices for installation |
| EN 1877-1-2000 | 混凝土构件的保护和修理用产品和系统 试验方法 与环氧树脂有关的反应功能 第1部分：环氧等效的测定 | Products and systems for the protection and repair of concrete structures - Test methods; reactive functions related to epoxy resins - Part 1: Determination of epoxy equivalent |
| EN 1877-2-2000 | 混凝土构件的保护和修理用产品和系统 试验方法 与环氧树脂有关的反应功能 第2部分：使用总碱度数值测定 | Products and systems for the protection and repair of concrete structures - Test methods; Reactive functions related to epoxydes resins - Part 2: Determination of amine functions using the total basicity number |
| EN 2329-1993 | 航空航天系列 纺织玻璃纤维预浸渍树脂 测定单位面积质量的试验方法 | Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of mass per unita area |
| EN 2330-1993 | 航空航天系列 纺织玻璃纤维预浸渍树脂 测定挥发物质含量的试验方法 | Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of the content of volatile matter |
| EN 2331-1993 | 航空航天系列 纺织玻璃纤维预浸渍树脂 测定单位面积树脂和纤维含量及纤维质量的试验方法 | Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of the resin and fibre content and mass of fibre per unit area |
| EN 2332-1993 | 航空航天系列 纺织玻璃纤维预浸渍树脂 测定树脂流速的试验方法 | Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of the resin flow |
| EN 2375-1992 | 航空航天系列 树脂预浸渍材料 生产批抽样程序 | Aerospace series - Resin preimpregnated materials - Production batch sampling procedure |
| EN 2559-1997 | 航空航天系列 碳纤维预浸渍物 树脂成分 树脂和纤维含量及单位面积纤维质量的测定 | Aerospace series - Carbon fibre preimpregnates - Determination of the resin and fibre content and the mass of fibre per unit area |
| EN 2564-1998 | 航空航天系列 碳纤维叠层板材 纤维、树脂含量和空隙率的测定 | Aerospace series - Carbon fibre laminates - Determination of the fibre, resin and void contents |
| EN 26874-1992 | 牙科树脂基窗沟封封闭剂 | Dental resin-based pit and fissure sealants (ISO 6874:1988) |
| EN 438-1-1991 | 装饰高压层压板(HPL) 以热固树脂为基质的板 第1部分：规范 | Decorative high-pressure laminates (HPL) - Sheets based on thermosetting resins - Part 1: Specifications (ISO 4586-1:1987 modified) |
| EN 438-2-1991 | 装饰高压层压板(HPL) 以热固树脂为基质的板 第2部分：特性测定 | Decorative high-pressure laminates (HPL) - Sheets based on thermosetting resins - Part 2: Determination of properties (ISO 4586-2:1988 modified) |
| EN 50089-1992+A1-1994 | 金属外壳充气高远开关设备和控制设备用的铸造树脂分隔板规范 | Cast resin partitions for metal enclosed gas-filled high voltage switchgear and controlgear |
| EN 60317-0-4-1998+A1-2000 | 特种绕组线规范 第0部分：一般要求 第4节:玻璃丝绕包浸树脂或浸渍漆裸扁铜线或漆包扁铜线 | Specifications for particular types of winding wires - Part 0: General requirements - Section 4: Glass-fibre wound resin or varnish impregnated, bare or enamelled rectangular copper wire (IEC 60317-0-4:1997) |
| EN 60317-0-6-2001 | 特种绕组线规范 第0-6部分：一般要求 玻璃丝绕包浸树脂或浸渍漆 裸或漆包圆铜线 | Specifications for particular types of winding wires - Part 0-6: General requirements - Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire (IEC 60317-0-6:2001) |
| EN 60317-48-2000 | 特种绕组线规范 第48部分：温度指数155、玻璃丝绕包树脂或漆浸渍裸或漆包圆铜线 | Specifications for particular types of winding wires - Part 48: Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire, temperature index 155 (IEC 60317-48:1999) |
| EN 60317-49-2000 | 特种绕组线规范 第49部分：温度指数180、玻璃丝绕包树脂或漆浸渍裸或漆包圆铜线 | Specifications for particular types of winding wires - Part 49: Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire, temperature index 180 (IEC 60317-49:1999) |
| EN 60317-50-2000 | 特种绕组线规范 第50部分：温度指数220、玻璃丝绕包树脂或漆浸渍裸或漆包圆铜线 | Specifications for particular types of winding wires - Part 50: Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire, temperature index 200 (IEC 60317-50:1999) |
| EN 60371-3-4-1995 | 以云母为基材的绝缘材料规范 第3部分：单项材料规范 活页4：聚酯薄膜补强B阶环氧树脂粘合云母纸 | Specification for insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 4: Polyester film-backed mica paper with a B-stage epoxy resin binder (IEC 60371-3-4:1992) |
| EN 60371-3-5-1995 | 以云母为基材的绝缘材料规范 第3部分：单项材料规范 活页5：后浸渍用玻璃布补强环氧树脂粘合云母纸 | Specification for insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 5: Glass-backed mica paper with an epoxy resin binder for post-impregnation (VPI) (IEC 60371-3-5:1992) |
| EN 60371-3-6-1995 | 以云母为基材的绝缘材料规范 第3部分：单项材料规范 活页6：补强玻璃布B阶环氧树脂粘合云母纸 | Specification for insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 6: Glass-backed mica paper with a B-stage epoxy resin binder (IEC 60371-3-6:1992) |
| EN 60371-3-7-1995 | 以云母为基材的绝缘材料 第3部分：单项材料规范 活页7：单根导线缠绕用环氧树脂粘合聚脂薄膜云母纸 | Insulating materials based on mica - Part 3: Specifications for individual materials - Sheet 7: Polyester film mica paper with an epoxy resin binder for single conductor taping (IEC 60371-3-7:1995 + Corrigendum 1995) |
| EN 60454-3-17-2001 | 电工用压敏粘带规范 第3部分：.单项材料规范 活页17：涂压敏粘合剂的复合聚脂/环氧树脂 | Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials; Sheet 17: Polyester/epoxy combinations with pressure-sensitive adhesive (IEC 60454-3-17:2001) |
| EN 60455-1-1998 | 电气绝缘用无溶剂可聚合树脂 第1部分：定义和一般要求 | Resin based reactive compounds used for electrical insulation - Part 1: Definitions and general requirements (IEC 60455-1:1998) |
| EN 60455-2-1999 | 电气绝缘用无溶剂可聚合树脂 第2部分：试验方法 | Resin based reactive compounds used for electrical insulation - Part 2: Methods of test (IEC 60455-2:1998) |
| EN 60455-3-1-2003 | 电气绝缘用电抗性化合物树脂 第3部分：单项材料规范 活页1：未填充的环氧树脂化合物 | Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials; Sheet 1: Unfilled epoxy resinous compounds (IEC 60455-3-1:2003) / Note: Endorsement notice |
| EN 60455-3-2-2003 | 电气绝缘用电抗性化合物树脂 第3部分：单项材料规范 活页2：填石英的环氧树脂化合物 | Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials; Sheet 2: Quartz filled epoxy resinous compounds (IEC 60455-3-2:2003) / Note: Endorsement notice |
| EN 60455-3-3-2003 | 电气绝缘用电抗性化合物树脂 第3部分：单项材料规范 活页3：未填充的聚亚氨酯化合物 | Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials; Sheet 3: Unfilled polyurethane compounds (IEC 60455-3-3:2003) / Note: Endorsement notice |
| EN 60455-3-4-2003 | 电气绝缘用电抗性化合物树脂 第3部分：单项材料规范 活页4：填聚亚氨酯化合物 | Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials; Sheet 4: Filled polyurethane compounds (IEC 60455-3-4:2003) / Note: Endorsement notice |
| EN 60455-3-5-2001 | 电气绝缘用无溶剂可聚合树脂 第3部分：单项材料规范 活页5：不馆和聚酯浸渍树脂 | Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials; Sheet 5: Unsaturated polyester based impregnating resins (IEC 60455-3-5:2001) |
| EN 60893-1-1994 | 电工用热固性树脂基工业刚性层压板规范 第1部分：定义、名称和一般要求 | Specification for industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements (IEC 60893-1:1987) |
| EN 60893-2-1994 | 电工用热固性树脂基工业刚性层压板规范 第２部分：试验方法 | Specification for industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test (IEC 60893-2:1992) |
| EN 60893-3-1-1994+A1-1997 | 电工用热固性树脂基工业刚性层压板规范 第3部分：专用材料规范 第 1活页：工业刚性层压板 | Specification for industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3: Specifications for indivdual materials - Sheet 1: Types of industrial rigid laminated sheets (IEC 60893-3-1:1992) / Note: To be replaced b |
| EN 60893-3-2-1995+A1-1999 | 电工用热固性树脂基工业刚性层压板规范 第二３部分：专用材料规范 活页２：环氧树脂基刚性层压板的要求 | Specification for industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Requirements for rigid laminated sheets based on epoxide resins (IEC 60893-3-2:1993) / |
| EN 60893-3-3-1995 | 电工用热固性树脂基工业刚性层压板规范 第３部分：专用材料规范 活页３：对三聚氰胺树 脂硬质层压片的要 | Specification for industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 3: Requirements for rigid laminated sheets based on melamine resins (IEC 60893-3-3:1993) |
| EN 60893-3-4-1995 | 电工用热固性树脂基工业刚性层压板规范 第3部分：专用材料规范 活页4：酚醛树脂基刚性层压板的要求 | Specification for industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 4: Requirements for rigid laminated sheets based on phenolic resins (IEC 60893-3-4:1993) |
| EN 60893-3-5-1995 | 电工用热固性树脂基工业刚性层压板规范 第３部分：专用材料规范 活页５：聚酯树脂基刚性层压薄板的要求 | Specification for industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 5: Requirements for rigid laminated sheets based on polyester resins (IEC 60893-3-5:1993) |
| EN 60893-3-6-1995 | 电工用热固性树脂基工业刚性层压板规范 第３部分：专用材料规范 活页６：对硅氧烷树脂基刚性层压板的要求 | Specification for industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 6: Requirements for rigid laminated sheets based on silicone resins (IEC 60893-3-6:1993) |
| EN 60893-3-7-1995 | 电工用热固性树脂基工业刚性层压板规范 第３部分：专用材料规范 活页７：聚酰亚胺树脂基刚性层压薄板的要 | Specification for industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 7: Requirements for rigid laminated sheets based on polyimide resins (IEC 60893-3-7:1994) |
| EN 61212-1-1995 | 电工用热固性树脂工业硬质圆形层压管和棒 第1部分：一般要求 | Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 1: General requirements (IEC 61212-1:1995) |
| EN 61212-2-1996 | 电工用热固性树脂工业硬质圆形层压管和棒 第2部分：试验方法 | Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test (IEC 61212-2:1995) |
| EN 61212-3-1-1995 | 电工用热固性树脂工业硬质圆形层压管和棒 第3部分：单项材料规范 活页1：圆形层压卷制管 | Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Round laminated rolled tubes (IEC 61212-3-1:1995) |
| EN 61212-3-2-1995 | 电工用热固性树脂工业硬质圆形层压管和棒 第3部分：单项材料规范 活页2：圆形层压模制管 | Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Round laminated moulded tubes (IEC 61212-3-2:1995) |
| EN 61212-3-3-1995 | 电工用热固性树脂工业硬质圆形层压管和棒 第3部分：单项材料规范 活页3：圆形层压模制棒 | Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 3: Round laminated moulded rods (IEC 61212-3-3:1995) |
| EN 62011-1-2002 | 绝缘材料 以热固树脂为基础的电气用矩形和六角形横截面工业用、刚性的、模制的、层状管和棒材 第1部分： | Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements (IEC 62011-1:2002) / |
| EN ISO 10082-1999 | 塑料 酚醛树脂 分类和试验方法 | Plastics - Phenolic resins - Classification and test methods (ISO 10082:1999) |
| EN ISO 1060-1-1999 | 塑料 氯乙烯的均聚物和共聚树脂 第1部分：命名体系和基本规范 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications (ISO 1060-1:1998) |
| EN ISO 1060-2-1999 | 塑料 氯乙烯的均聚物和共聚树脂 第2部分：试样的制备和性能的测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 2: Preparation of test samples and determination of properties (ISO 1060-2:1998) |
| EN ISO 10618-1999 | 碳纤维 树脂浸渍纱拉伸性能的测定 | Carbon fibre - Determination of tensile properties of resin-impregnated yarns (ISO 10618:1999) |
| EN ISO 11376-2001 | 塑料 环氧树脂和缩水甘油基酯 无机氯的测定 | Plastics - Epoxy resins and glycidyl esters - Determination of inorganic chlorine (ISO 11376:1997) |
| EN ISO 11401-1998 | 塑料 酚醛树脂 用液相色谱法分离 | Plastics - Phenolic resins - Separation by liquid chromatography (ISO 11401:1993) |
| EN ISO 11402-1998 | 塑料 综合树脂 游离甲醛的测定 | Plastics - Condensation resins - Determination of free formaldehyde (ISO 11402:1993) |
| EN ISO 11409-1998 | 塑料 酚醛树脂 用差示扫描量热法测定反应热及温度 | Plastics - Phenolic resins - Determination of heats and temperatures of reaction by differential scanning calorimetry (ISO 11409:1993) |
| EN ISO 11667-1999 | 纤维增强塑料 模塑料和预浸料 树脂、增强纤维和矿物质填料含量的测定 溶解法 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of resin, reinforced-fibre and mineral-filler content - Dissolution methods (ISO 11667:1997) |
| EN ISO 11668-2001 | 色漆和清漆用粘合剂 氯化聚合物树脂 通用试验方法 | Binders for paints and varnishes - Chlorinated polymerization resins - General methods of test (ISO 11668:1997) |
| EN ISO 11908-1998 | 色漆和清漆用粘合剂 胺基树脂 一般试验法 | Binders for paints and varnishes - Amino resins - General methods of test (ISO 11908:1996) |
| EN ISO 11909-1998 | 色漆和清漆用粘合剂 聚异氰酸酯树脂 一般试验法 | Binders for paints and varnishes - Polyisocyanate resins - General methods of test (ISO 11909:1996) |
| EN ISO 12215-1-2000 | 小艇 船体结构和尺寸 第1部分：材料：热固性树脂、玻璃纤维增强材料、基准层压板 | Small craft - Hull construction and scantlings - Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate (ISO 12215-1:2000) |
| EN ISO 1264-1997 | 塑料 氯乙烯均聚物和共聚物树脂 水萃取物的pH值测定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of pH of aqueous extract (ISO 1264:1980) |
| EN ISO 1265-1997 | 塑料 聚氯乙烯树脂 杂质和外来杂质数的测定 | Plastics - Polyvinyl chloride resins - Determination of number of impurities and foreign particles (ISO 1265:1979) |
| EN ISO 15252-1-1999 | 塑料 环氧树脂模塑化合物(EP-PMCs) 第1部分：命名体系及基本规范 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 1: Designation system and basis for specifications (ISO 15252-1:1999) |
| EN ISO 15252-2-1999 | 塑料 环氧树脂模塑化合物(EP-PMCs) 第2部分：试样的准备和特性的测定 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 15252-2:1999) |
| EN ISO 15252-3-1999 | 塑料 环氧树脂模塑化合物(EP-PMCs) 第3部分：对所选模塑化合物的要求 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 15252-3:1999) |
| EN ISO 1624-2001 | 塑料 聚乙烯均聚物和共聚物树脂 水中筛析 | Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis in water (ISO 1624:2001) |
| EN ISO 1628-2-1998 | 塑料 用毛细管粘度计测定稀溶液中聚合物的粘度 第2部分：聚氯乙烯树脂 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 2: Poly(vinyl chloride) resins (ISO 1628-2:1998) |
| EN ISO 1675-1998 | 塑料 液态树脂 比重瓶法测定密度 | Plastics - Liquid resins - Determination of density by the pyknometer method (ISO 1675:1985) |
| EN ISO 2114-2000 | 塑料（聚酯树脂）、色漆和清漆（胶粘合剂） 部分酸值和总酸值的测定 | Plastics (polyester resins) and paints and varnishes (binders) - Determination of partial acid value and total acid value (ISO 2114:2000) |
| EN ISO 2535-2002 | 塑料 不饱和聚脂树脂 25℃时胶凝时间的测量 | Plastics - Unsaturated polyester resins - Measurement of gel time at ambient temperature (ISO 2535:2001) |
| EN ISO 2554-1998 | 塑料 不饱和聚脂树脂 羟基值的测定 | Plastics - Unsaturated polyester resins - Determination of hydroxyl value (ISO 2554:1997) |
| EN ISO 2555-1999 | 塑料 液态或乳态或分散状树脂 用落球式粘度计测定表观粘度 | Plastics - Resins in the liquid state or as emulsions or dispersions - Determination of apparent viscosity by the Brookfield test method (ISO 2555:1989) |
| EN ISO 308-1997 | 塑料 酚醛模塑材料 丙酮可溶性物质(在未模塑状态时表现树脂含量)的测定 | Plastics - Phenolic moulding materials - Determination of acetone-soluble matter (apparent resin content of material in the unmoulded state) (ISO 308:1994) |
| EN ISO 3219-1994 | 塑料 液态或乳态或分散状的聚合物/树脂 使用规定剪切率的旋转式粘度计测定粘度 | Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate (ISO 3219:1993) |
| EN ISO 3521-1999 | 塑料 不饱和聚酯和环氧树脂 总体积收缩率的测定 | Plastics - Unsaturated polyester and epoxy resins - Determination of overall volume shrinkage (ISO 3521:1997) |
| EN ISO 3672-1-2001 | 塑料 不饱和聚酯树脂 第1部分：命名体系 | Plastics - Unsaturated-polyester resins (UP-R) - Part 1: Designation system (ISO 3672-1:2000) |
| EN ISO 3672-2-2001 | 塑料 不饱和聚酯树脂 第2部分：试样的制备和特性的测定 | Plastics - Unsaturated-polyester resins (UP-R) - Part 2: Preparation of test specimens and determination of properties (ISO 3672-2:2000) |
| EN ISO 3673-1-1999 | 塑料 环氧树脂 第1部分：命名 | Plastics - Epoxy resins - Part 1 : Designation (ISO 3673-1:1996) |
| EN ISO 3673-2-1999 | 塑料 环氧树脂 第2部分：试样的制备和特性的测定 | Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties (ISO 3673-2:1999) |
| EN ISO 4583-1998 | 塑料 环氧树脂和有关材料 易皂化氯的测定 | Plastics - Epoxy resins and related materials - Determination of easily saponifiable chlorine (ISO 4583:1998) |
| EN ISO 4597-1-1997 | 塑料 环氧树脂用固化剂和促进剂 第1部分：命名 | Plastics - Hardeners and accelerators for epoxide resins - Part 1: Designation (ISO 4597-1:1983) |
| EN ISO 4608-1998 | 塑料 氯乙烯 一般用途氯乙烯均聚物和共聚物树脂 室温下增塑剂吸收的测定 | Plastics - Vinylchlorid(VC)-homopolymere and copolymer resins of vinyl chloride for general use - Determination of plasticizer absorption at room temperature (ISO 4608:1998) |
| EN ISO 4610-2001 | 塑料 氯乙烯均聚物和共聚物树脂 用空气喷射筛滤器进行筛析 | Plastics - Vinyl chloride homopolymer and copolymer resins - Sieve analysis using air-jet sieve apparatus (ISO 4610:2001) |
| EN ISO 4615-1999 | 塑料 不饱和聚酯和环氧树脂 总氯量的测定 | Plastics - Unsaturated polyesters and epoxide resins - Determination of total chlorine content (ISO 4615:1979) |
| EN ISO 4895-1999 | 塑料 液态环氧树脂 结晶性的测定 | Plastics - Liquid epoxy resins - Determination of tendency to crystallize (ISO 4895:1997) |
| EN ISO 7327-1997 | 塑料 环氧树脂用固化剂和促进剂 酸酐中游离酸测定 | Plastics - Hardeners and accelerators for epoxide resins - Determination of free acid in acid anhydride (ISO 7327:1994) |
| EN ISO 8618-1998 | 塑料 液态酚醛树脂 非挥发性物质的常规测定 | Plastics - Liquid phenolic resins - Conventional determination of non-volatile matter (ISO 8618:1995) |
| EN ISO 8619-1998 | 塑料 酚醛树脂粉 在加热玻璃盘上流动距离的测定 | Plastics - Phenolic resin powder - Determination of flow distance on a heated glass plate (ISO 8619:1995) |
| EN ISO 8620-1995 | 塑料 酚醛树脂粉 筛析 用喷气筛设备进行过滤分析 | Plastics - Phenolic resin powder - Sieve analysis - Sieve analysis using air-jet sieve apparatus (ISO 8620:1986) |
| EN ISO 8974-2002 | 塑料 酚醛树脂 用气体色谱法测定残余酚含量 | Plastics - Phenolic resins - Determination of residual phenol content by gas chromatography (ISO 8974:2002) |
| EN ISO 8975-1995 | 塑料 酚醛树脂 pH值的测定 | Plastics - Phenolic resins - Determination of pH (ISO 8975:1989) |
| EN ISO 8987-1998 | 塑料 酚醛树脂 在Ｂ转变试验板上的活化性能的测定 | Plastics - Phenolic resins - Determination of reactivity on a B-transformation test plate (ISO 8987:1995) |
| EN ISO 8988-1997 | 塑料 酚醛树脂 六次甲基四胺含量的测定 凯氏法和过氯酸法 | Plastics - Phenolic resins - Determination of hexamethylenetetramine content - Kjeldahl method and perchloric acid method (ISO 8988:1995) |
| EN ISO 8989-1998 | 塑料 液态酚醛树脂 水溶物的测定 | Plastics - Liquid phenolic resins - Determination of water miscibility (ISO 8989:1995) |
| EN ISO 9020-1998 | 色漆和清漆用粘合剂 胺类树脂的游离甲醛含量的测定 亚硫酸钠滴定法 | Binders for paints and varnishes - Determination of free-formaldehyde content of amino resins - Sodium sulfite titrimetric method (ISO 9020:1994, including Technical Corrigendum 1:1996) |
| EN ISO 9396-2000 | 塑料 酚醛树脂 用自动装置在给定温度下对凝胶时间的测定 | Plastics - Phenolic resins - Determination of the gel time at a given temperature using automatic apparatus (ISO 9396:1997) |
| EN ISO 9397-1997 | 塑料 酚醛树脂 游离甲醛含量的测定 盐酸胲法 | Plastics - Phenolic resins - Determination of free-formaldehyde content - Hydroxylamine hydrochloride method (ISO 9397:1995) |
| EN ISO 9771-1997 | 塑料 酚醛树脂 在酸性条件处理时液体酚醛树脂假绝热温升的测定 | Plastics - Phenolic resins - Determination of the pseudo-adiabatic temperature rise of liquid resols when cured under acid conditions (ISO 9771:1995) |
| EN ISO 9944-1995 | 塑料 酚醛树脂 树脂萃取物电导率的测定 | Plastics - Phenolic resins - Determination of electrical conductivity of resin extracts (ISO 9944:1990) |
| HD 22.15 S1-1999 | 额定电压450/750V及以下的橡胶绝缘电缆 第15部分：绝缘并包覆耐热硅树脂橡胶的多芯电缆 | Rubber insulated cables of rated voltages up to and including 450/750 V - Part 15: Multicore cables insulated and sheathed with heat resistant silicone rubber |
| HD 22.3 S3-1995+A1-1999 | 额定电压450/750V及以下的橡胶绝缘电缆 第3部分：耐热硅树脂橡胶绝缘电缆 | Rubber insulated cables of rated voltages up to and including 450/750 V - Part 3: Heat resistant silicone rubber insulated cables (IEC 60245-3:1980, modified) / Note: To be replaced by prHD 22.3 S4 (2003-05). |
| HD 307.2.2 S1-1986 | 电绝缘用无溶剂可聚合树脂化合物规范 第2部分：试验方法 电工用涂覆粉末试验方法 | Specification for solventless polymerisable resinous compounds used for electrical insulation- Part 2: Methods of test - Test methods for coating powders for electrical purposes |
| HD 307.3.11 S1-1990 | 电绝缘用无溶剂可聚合树脂化合物规范 第3部分：单项材料规范 活页11：环氧树脂涂覆粉末 | Specification for solventless polymerisable resinous compounds used for electrical insulation - part 3: Specifications for individual materials - sheet 11: Epoxy resin-based coating powders |
| HD 565 S1-1993 | 电工用途硅树脂液规范 | Specifications for silicone liquids for electrical purposes (IEC 60836:1988) |
| HD 621 S1-1996+A1-2001 | 中压树脂浸渍纸绝缘配电电缆 | Medium voltage impregnated paper insulated distribution cables |
| HD 629.2 S1-1997+A1-2001 | 额定电压3.6/6(7.2) kV至20.8/36(42) kV的电力电缆用附件的试验要求 第2部分：树脂浸渍纸绝缘电缆 | Test requirements on accessories for use on power cables of rated voltage from 3,6/6(7,2) kV up to 20,8/36(42) kV - Part 2: Cables with impregnated paper insulation / Note: To be replaced by prHD 629.2 S2 (2003-10). |
| HD 631.1 S1-1998 | 材料特性 第1部分：电缆附件中使用的化合物：硫化前和硫化状态下的树脂化合物 | Material characterisation - Part 1: Compounds for use in cable accessories: Resinous compounds before cure and in the cured state |
| prEN 10310-2002 | 岸上和海上管路钢管及配件 双层环氧树脂和聚酰胺基涂层的内衬和外衬 | Steel tubes and fittings for onshore and offshore pipelines - Internal and external polyamide powder based coatings |
| prEN 1115-2-1997 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第2部分：具挠 | Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints |
| prEN 1115-4-1993 | 压力下地下排水和排污装置用塑料管道系统 基于聚脂树脂的玻璃增强热固性塑料（GRP） 第4部分：辅助设备 | Plastics piping systems for underground drainage and sewerage under pressure; glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP); part 4 (informative): ancillary equipment |
| prEN 1115-6-1997 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第6部分：安装 | Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 6: Practices for installation |
| prEN 1115-7-1995 | 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP） 第7部分：一致 | Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 7: Assessment of conformity |
| prEN 1331-1994 | 热固性树脂基连续挤压装饰层压板(CPL) | Decorative continuously pressed laminates (CPL) based on thermosetting resins |
| prEN 14364-2002 | 有或无压排水和排污塑料管线系统 玻璃纤维增强的未饱和的聚酯树脂基热固塑料管 塑料管管件及接头规范 | Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints |
| prEN 1544-2003 | 混凝土结构的保护和修理用产品和系统 试验方法 合成树脂产品 当拉伸力为+23和+50时蠕变强度的测量 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of creep under sustained tensile load for synthetic resin products (PC) for the anchoring of reinforcing bars |
| prEN 1636-1-1996 | 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第1部分：总则 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 1: General |
| prEN 1636-2-1996 | 无压力排水道和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第2部分：带有挠 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints |
| prEN 1636-4-1994 | 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第4部分：辅助设备 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 4: Ancillary equipment |
| prEN 1796-2-1995 | 有或无压力供水用塑料管道系统 非饱和性聚脂树脂基玻璃增强热固性塑料 第2部分：带挠性、缩口活节或刚性 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints |
| prEN 1796-2003 | 有或无压力供水用塑料管道系统 非饱和性聚脂树脂基玻璃增强热固性塑料 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) |
| prEN 1796-4-1995 | 有或无压力供水有塑料管道系统聚合物树脂（UP）基玻璃纤维增强热固性塑料（GRP） 第4部分：辅助设备 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 4: Ancillary equipment |
| prEN 1796-5-1995 | 有或无压力供水用塑料管道系统聚合物树脂（UP）基玻璃纤维增强热固性塑料（GRP） 第5部分：系统用途的适合 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 5: Fitness for the purpose of the system |
| prEN 1796-6-1995 | 有或无压力供水用塑料管道系统聚合物树脂（UP）基玻璃纤维增强热固性塑料（GRP） 第6部分：推荐的安装实践 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 6: Recommended practice for installation |
| prEN 1878-1995 | 混凝土构件的保护和修理用产品和系统 试验方法 与环氧树脂有关的反应功能 聚合物热解重量分析法 温度扫 | Products and systems for the protection and repair of concrete structures - Test methods - Reactive functions related to epoxy resins - Thermogravimetry of polymers - Temperature scanning method |
| prEN 2833-3-1997 | 航空航天系列 玻璃纤维热固预浸渍物 技术规范 第３部分：塑化温度达180 ℃ 、持续使用达120℃玻璃纤维／ | Aerospace series - Glass fibre thermosetting preimpregnates - Technical specification - Part 3: Glass fabric/epoxy resin preimpregnate curing at up to 180℃ for continuous use up to 120℃ |
| prEN 2833-4-1997 | 航空航天系列 玻璃纤维热固预浸渍物 技术规范 第４部分：塑化温度达125 ℃、持续使用达 80 ℃单向玻璃／ | Aerospace series - Glass fibre thermosetting preimpregnates - Technical specification - Part 4: Unidirectional glass/epoxy resin preimpregnate curing at up to 125℃ for continuous use up to 80℃ |
| prEN 2833-5-2001 | 航空航天系列 玻璃纤维热固预浸渍物 技术规范 第５部分：玻璃纤维／酚醛树脂预浸渍物 | Aerospace series - Glass fibre thermosetting preimpregnates; Technical specification - Part 5: Glass fabric/phenolic resin preimpregnate |
| prEN 2850-1997 | 航空航天系列 碳纤维增强热固树脂单向叠层板 平衡纤维方向的压缩测试 | Aerospace series - Carbon fibre thermosetting resin unidirectional laminates - Compression test parallel to fibre direction |
| prEN 438-1-2002 | 高压装饰层压板(HPL) 以热固树脂为基质的板（通常称为层压板） 第1部分：介绍和一般信息 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 1: Introduction and general information |
| prEN 438-2-2002 | 高压装饰层压板(HPL) 以热固树脂为基质的板（通常称为层压板） 第2部分：特性测定 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 2: Determination of properties |
| prEN 438-3-2002 | 高压装饰层压板(HPL) 以热固树脂为基质的板（通常称为层压板） 第3部分：胶接支撑下层用的少于2毫米厚的 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 3: Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates |
| prEN 438-4-2002 | 高压装饰层压板(HPL) 以热固树脂为基质的板（通常称为层压板） 第4部分：厚度为2毫米或以上的压制层压板 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 4: Classification and specifications for compact laminates of thickness 2 mm and greater |
| prEN 438-5-2002 | 高压装饰层压板(HPL) 以热固树脂为基质的板（通常称为层压板） 第5部分：少于2毫米厚的地板等级层压板分 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 5: Classification and specifications for flooring grade laminates less than 2 mm thick |
| prEN 438-6-2002 | 高压装饰层压板(HPL) 以热固树脂为基质的板（通常称为层压板） 第6部分：厚度为2毫米或以上的表面等级压 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 6: Classification and specifications for exterior-grade compact laminates of thickness 2 mm and greater |
| prEN 438-7-2002 | 高压装饰层压板(HPL) 以热固树脂为基质的板（通常称为层压板） 第7部分：内外墙和天花板装饰用的压制层 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes |
| prEN 6085-1999 | 航空航天系列 非金属材料 环氧树脂面膜 | Aerospace series - Non-metallic materials - Epoxy surfacing films |
| prEN 60893-1-2003 | 电工用热固性树脂基工业刚性层压板 第1部分：定义、名称和一般要求 草案 | IEC 60893-1, Ed. 2: Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements |
| prEN 60893-2-2003 | 电工用热固性树脂基工业刚性层压板 第２部分：试验方法 | IEC 60893-2, Ed. 2: Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test |
| prEN 60893-3-1-2003 | 电工用热固性树脂基工业刚性层压板 第３部分： 专用材料规范 活页１：工业硬质层压片类型 | IEC 60893-3-1, Ed. 2: Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3-1: Specifications for individual materials; Requirements for types of industrial rigid laminated sheets / Note: |
| prEN 60893-3-2-2003 | 电工用热固性树脂基工业刚性层压板规范 第３部分：专用材料规范 活页２：环氧树脂基刚性层压板的要求 | IEC 60893-3-2, Ed. 2: Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3-2: Specifications for individual materials; Requirements for rigid laminated sheets based on epoxy resins / Note |
| prEN 60893-3-3-2003 | 电工用热固性树脂基工业刚性层压板规范 第３部分：专用材料规范 活页３：对三聚氰胺树 脂硬质层压片的要 | IEC 60893-3-3, Ed. 2: Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3-3: Specifications for individual materials; Requirements for rigid laminated sheets based on melamine resins / N |
| prEN 60893-3-4-2003 | 电工用热固性树脂基工业刚性层压板规范 第3部分：专用材料规范 第4活页：酚醛树脂基刚性层压板的要求 | IEC 60893-3-4, Ed. 2: Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3-4: Specifications for individual materials; Requirements for rigid laminated sheets based on phenolic resins / N |
| prEN 60893-3-5-2003 | 电工用热固性树脂基工业刚性层压板规范 第３部分：专用材料规范 活页５：聚酯树脂基刚性层压薄板的要求 | IEC 60893-3-5, Ed. 2: Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3-5: Specifications for individual materials; Requirements for rigid laminated sheets based on polyester resins / |
| prEN 60893-3-6-2003 | 电工用热固性树脂基工业刚性层压板规范 第３部分：专用材料规范 活页６：对硅氧烷树脂基刚性层压板的要求 | IEC 60893-3-6, Ed. 2: Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3-6: Specifications for individual materials; Requirements for rigid laminated sheets based on silicone resins / N |
| prEN 60893-3-7-2003 | 电工用热固性树脂基工业刚性层压板规范 第３部分：专用材料规范 活页７：聚酰亚胺树脂基刚性层压薄板的要 | IEC 60893-3-7, Ed. 2: Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 3-7: Specifications for individual materials; Requirements for rigid laminated sheets based on polyimide resins / |
| prEN 62011-2-2003 | 以热固树脂为基础的电气用途矩形和六角形横截面工业用、刚性的、模制的、层状管和棒材 第2部分：试验方法 | IEC 62011-2, Ed. 1: Insulating materials - Industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross-section, based on thermosetting resins for electrical purposes - Part 2: Methods of test |
| prEN 62011-3-1-2003 | 以热固树脂为基础的电气用途矩形和六角形横截面工业用、刚性的、模制的、层状管和棒材 第3部分：个体材料 | () |
| prEN 7000-11-1999 | 航空航天系列 非金属材料 材料标准的编写和表示的规则 第11部分：预浸渍树脂 | Aerospace series - Non-metallic materials - Rules for drafting and presentation of material standards - Part 11: Preimpregnates |
| prEN ISO 10618-2002 | 碳纤维 树脂浸渍纱拉伸性能的测定 | Carbon fibre - Determination of tensile properties of resin-impregnated yarn (ISO/DIS 10618:2002) |
| 编号 | 中文名称 | 英文名称 |