| 编号 | 中文名称 | 英文名称 |
|---|
| IEC 60099-1 AMD 1-1999
| 避雷器 第1部分:交流系统用有间隙阀式避雷器 修改件1
| Surge arresters - Part 1: Non-linear resistor type gapped arresters for a.c. systems; Amendment 1
|
| IEC 60099-1-1991
| 避雷器 第1部分:交流系统用有间隙阀式避雷器
| Surge arresters; part 1: non-linear resistor type gapped surge arresters for a.c. systems
|
| IEC 60534-1-2005
| 工业过程控制阀.第1部分:控制阀术语和一般考虑
| Industrial-process control valves - Part 1: Control valve terminology and general considerations
|
| IEC 60534-2-1 Corrigendum 1-2000
| 工业过程控制阀.第2-1部分:流通能力.安装条件下流体流量的校准公式
| Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions
|
| IEC 60534-2-1-1998
| 工业过程控制阀 第2-1部分:流通能力 安装条件下流体流量的校准公式
| Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions
|
| IEC 60534-2-3-1997
| 工业过程控制阀 第2-3部分:流通能力 试验规程
| Industrial-process control valves - Part 2-3: Flow capacity - Test procedures
|
| IEC 60534-2-4-1989
| 工业过程控制阀 第2部分:流通能力 第4节:固有流动特性和变化范围
| Industrial-process control valves; part 2: flow capacity; section four: inherent flow characteristics and rangeability
|
| IEC 60534-2-5-2003
| 工业过程控制阀.第2-5部分:流通能力.通过有段间恢复能力的多段控制阀门的流体流量的校准公式
| Industrial-process control valves - Part 2-5: Flow capacity; Sizing equations for fluid flow through multistage control valves with interstage recovery
|
| IEC 60534-3-1-2001
| 工业过程控制阀.第3-1部分:尺寸.法兰面对面尺寸,两路,直型和法兰中心对面尺寸,两路,球形,角型控制阀门
| Industrial-process control valves - Part 3-1: Dimensions; Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves
|
| IEC 60534-3-2-2001
| 工业过程控制阀 第3-2部分：尺寸 旋转控制阀（除蝶阀外）的端面间距尺寸
| Industrial-process control valves - Part 3-2: Dimensions; Face-to-face dimensions for rotary control valves except butterfly valves
|
| IEC 60534-3-3-1998
| 工业过程控制阀 第3-3部分:尺寸 对接焊的双通球形、直型控制阀的首尾相接尺寸
| Industrial-process control valves - Part 3-3: Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves
|
| IEC 60534-4-2006
| 工业过程控制阀.第4部分:检验和常规试验
| Industrial process control valves - Part 4: Inspection and routine testing
|
| IEC 60534-5-2004
| 工业过程控制阀.第5部分:标记
| Industrial-process control valves - Part 5: Marking
|
| IEC 60534-6-1-1997
| 工业过程控制阀 第6部分:定位器联接到控制阀执行机构的安装细则 第1节:线型执行机构上定位器的安装
| Industrial-process control valves - Part 6: Mounting details for attachment of positioners to control valves - Section 1: Positioner mounting on linear actuators
|
| IEC 60534-6-2-2000
| 工业过程控制阀 第6部分:定位器联接到控制阀执行机构的安装细则 环形执行机构定位器
| Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves; Positioner mounting on rotary actuators
|
| IEC 60534-7-1989
| 工业过程控制阀 第7部分:控制阀数据表
| Industrial-process control valves; part 7: control valve data sheet
|
| IEC 60534-8-1-2005
| 工业过程控制阀.第8-1部分:噪声的考虑.气动流流经控制阀产生的噪声的实验室测量
| Industrial-process control valves - Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves
|
| IEC 60534-8-2-1991
| 工业过程控制阀 第8部分:噪声的考虑 第2节:流动液流经控制阀产生的噪声的实验室测量
| Industrial-process control valves; part 8: noise considerations; section 2: laboratory measurement of noise generated by hydrodynamic flow through control valves
|
| IEC 60534-8-3-2000
| 工业过程控制阀 第8-3部分:噪声的考虑 控制阀的气动噪声预测法
| Industrial-process control valves - Part 8-3: Noise considerations; Control valve aerodynamic noise prediction method
|
| IEC 60534-8-4 Corridendum 1-2006
| 工业过程控制阀.第8-4部分:噪声问题.预测液体动力流产生的噪声.勘误1
| Industrial-process control valves - Part 8-4: Noise considerations - Prediction of noise generated by hydrodynamic flow; Corrigendum 1
|
| IEC 60534-8-4-2005
| 工业过程控制阀.第8-4部分:噪声问题.预测液体动力流产生的噪声
| Industrial-process control valves - Part 8-4: Noise considerations - Prediction of noise generated by hydrodynamic flow
|
| IEC 60700-1 AMD 1-2003
| 高压直流(HVDC)电力传输用可控硅阀门.第1部分:电气试验.修改件1
| Thyristor valves for high voltage direct current (HVDC) power transmission - Part 1: Electrical testing; Amendment 1
|
| IEC 60700-1 Edition 1.1-2003
| 高压直流(HVDC)电力传输用可控硅阀.第1部分:电气试验
| Thyristor valves for high voltage direct current (HVDC) power transmission - Part 1: Electrical testing
|
| IEC 60700-1-1998
| 高压直流(HVDC)输电用晶闸管阀 第1部分:电气试验
| Thyristor valves for high voltage direct current (HVDC) power transmission - Part 1: Electrical testing
|
| IEC 60730-2-17 AMD 1-2000
| 家用和类似用途的自动电气控制.第2-17部分:电气操作气体阀门的特殊要求,包括机械要求.修改件1
| Automatic electrical controls for household and similar use - Part 2-17: Particular requirements for electrically operated gas valves, including mechanical requirements; Amendment 1
|
| IEC 60730-2-17 Edition 1.1-2001
| 家用和类似用途的自动电气控制.第2-17部分:电控气阀的特殊要求,包括机械要求
| Automatic electrical controls for household and similar use - Part 2-17: Particular requirements for electrically operated gas valves, including mechanical requirements
|
| IEC 60730-2-17-1997
| 家用及类似用途的电气自动控制器 第2-17部分:电动气阀的特殊要求(包括机械要求)
| Automatic electrical controls for household and similar use - Part 2: Particular requirements for electrically operated gas valves, including mechanical requirements
|
| IEC 60730-2-19 AMD 1-2000
| 家用和类似用途的自动电气控制.第2-19部分:电气操作油阀门的特殊要求,包括机械要求.修改件1
| Automatic electric controls for household and similar use - Part 2-19: Particular requirements for electrically operated oil valves, including mechanical requirements; Amendment 1
|
| IEC 60730-2-19 Edition 1.1-2001
| 家用和类似用途的自动电气控制.第2-19部分:电控油阀的特殊要求,包括机械要求
| Automatic electric controls for household and similar use - Part 2-19: Particular requirements for electrically operated oil valves, including mechanical requirements
|
| IEC 60730-2-19-1997
| 家用及类似用途的电气自动控制器 第2-19部分:电动油阀的特殊要求(包括机械要求)
| Automatic electric controls for household and similar use - Part 2: Particular requirements for electrically operated oil valves, including mechanical requirements
|
| IEC 60730-2-8 AMD 1-2002
| 家用和类似用途的电气自动控制器.第2-8部分:电动水阀的特殊要求(包括机械要求).修改件1
| Automatic electrical controls for household and similar use - Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements; Amendment 1
|
| IEC 60730-2-8 Edition 2.1-2003
| 家用和类似用途的电器自动控制器.第2-8部分:电动水阀的特殊要求(包括机械要求)
| Automatic electrical controls for household and similar use - Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements
|
| IEC 60730-2-8-2000
| 家用和类似用途的电气自动控制器 第2-8部分:电动水阀的特殊要求(包括机械要求)
| Automatic electrical controls for household and similar use - Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements
|
| IEC 60896-21-2004
| 固定式铅酸蓄电池组.第21部分:阀调整型.试验方法
| Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test
|
| IEC 60896-22-2004
| 固定式铅酸蓄电池组.第22部分:阀调整型.要求
| Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements
|
| IEC 61056-1-2002
| 通用铅酸蓄电池组(阀门调节型).第1部分:一般要求、功能特性.试验方法
| General purpose lead-acid batteries (valve-regulated types) - Part 1: General requirements, functional characteristics; Methods of test
|
| IEC 61056-2-2002
| 通用铅酸蓄电池组(阀门调节型).第2部分:尺寸、端子和标记
| General purpose lead-acid batteries (valve-regulated types) - Part 2: Dimensions, terminals and marking
|
| IEC 61148 Corrigendum 1-1995
| 阀器件堆和组合装置以及电力变流设备的端子标记
| Terminal markings for valve device stacks and assemblies and for power convertor equipment
|
| IEC 61148-1992
| 阀器件堆和组合装置以及电力变流设备的端子标记
| Terminal markings for valve device stacks and assemblies and for power convertor equipment
|
| IEC 61514-2-2004
| 工业过程控制系统.第2部分:气动输出智能阀门定位器性能评定方法
| Industrial process control systems - Part 2: Methods of evaluating the performance of intelligent valve positioners with pneumatic outputs
|
| IEC 61514-2000
| 工业过程控制系统 气动输出阀门定位器性能评定方法
| Industrial-process control systems - Methods of evaluating the performance of valve positioners with pneumatic outputs
|
| IEC 61954 AMD 1-2003
| 送电和配电系统用电力电子设备.静态变量补偿器用可控硅阀门的试验.修改件1
| Power electronics for electrical transmission and distribution systems - Testing of thyristor valves for static VAR compensators; Amendment 1
|
| IEC 61954 Corrigendum 1-1999
| 输电和配电系统用电力电子设备.静态无功功率补偿器用晶闸管阀的试验
| Power electronics for electrical transmission and distribution systems - Testing of thyristor valves for static VAR compensators
|
| IEC 61954-1999
| 输电和配电系统用电力电子设备 静态无功功率补偿器用晶闸管阀的试验
| Power electronics for electrical transmission and distribution systems - Testing of thyristor valves for static VAR compensators
|
| IEC/TR3 61056-3-1991
| 便携式铅酸电池和蓄电池组(阀门调节型) 第3部分:电器使用的安全建议
| Portable lead-acid cells and batteries (valve-regulated types); part 3: safety recommendations for use in electric appliances
|
| ISO 10156-1996
| 气体和气体混合物 为选择气瓶阀出气口测定气体的潜在燃烧性和氧化能力
| Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets
|
| ISO 1023-1974
| 航空器 高压空气充气阀
| Aircraft; High pressure air charging valves
|
| ISO 10294-1-1996
| 耐火试验 用于空气调节系统的防火阀 第1部分:试验方法
| Fire resistance tests - Fire dampers for air distribution systems - Part 1: Test method
|
| ISO 10294-2-1999
| 耐火试验 用于空气调节系统的防火阀 第2部分:试验结果的分类、校正和应用
| Fire resistance tests - Fire dampers for air distribution systems - Part 2: Classification, criteria and field of application of test results
|
| ISO 10294-3-1999
| 耐火试验 用于空气调节系统的防火阀 第3部分:试验方法指南
| Fire resistance tests - Fire dampers for air distribution systems - Part 3: Guidance on the test method
|
| ISO 10294-4-2001
| 耐火试验 用于空气调节系统的防火阀 第4部分：热释放机理试验
| Fire resistance tests - Fire dampers for air distribution systems - Part 4: Test of thermal release mechanism
|
| ISO 10294-5-2005
| 耐火试验.用于空气调节系统的防火阀.第5部分:膨胀防火阀
| Fire resistance tests - Fire dampers for air distribution systems - Part 5: Intumescent fire dampers
|
| ISO 10297-2006
| 可运输气瓶.气瓶阀.规范和型式试验
| Transportable gas cylinders - Cylinder valves - Specification and type testing
|
| ISO 10372-1992
| 液压传动 四油口和五油口伺服阀 安装面
| Hydraulic fluid power; four- and five-port servovalves; mounting surfaces
|
| ISO 10417-2004
| 石油和天然气工业.井下安全阀系统.设计、安装、操作和修整
| Petroleum and natural gas industries - Subsurface safety valve systems - Design, installation, operation and redress
|
| ISO 10432-2004
| 石油和天然气工业.下降孔设备.地下安全阀设备
| Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment
|
| ISO 10434-2004
| 石油、石油化学和相关工业用栓接帽状钢闸阀
| Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries
|
| ISO 10497-2004
| 阀门试验.阀门耐火试验要求
| Testing of valves - Fire type-testing requirements
|
| ISO 10522-1993
| 农业灌溉设备 直接作用的调压阀
| Agricultural irrigation equipment; direct-acting pressure-regulating valves
|
| ISO 10524-3-2005
| 医用气体设备用的压力调节器.第3部分:带气瓶阀的压力调节器
| Pressure regulators for use with medical gases - Part 3: Pressure regulators integrated with cylinder valves
|
| ISO 10631-1994
| 通用金属蝶阀
| Metallic butterfly valves for general purposes
|
| ISO 10692-1-2001
| 气瓶 微电子工业用气瓶阀的连接 第1部分：出口连接
| Gas cylinders - Gas cylinder valve connections for use in the micro-electronics industry - Part 1: Outlet connections
|
| ISO 10692-2-2001
| 气瓶 微电子工业用气瓶阀的连接 第2部分：阀与瓶连接的规范和型式试验
| Gas cylinders - Gas cylinder valve connections for use in the micro-electronics industry - Part 2: Specification and type testing for valve to cylinder connections
|
| ISO 10770-1-1998
| 液压传动 电调制液压控制阀 第1部分:四通流量控制阀的试验方法
| Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 1: Test methods for four-way directional flow control valves
|
| ISO 10770-2-1998
| 液压传动 电调制液压控制阀 第2部分:三通流量控制阀的试验方法
| Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 2: Test methods for three-way directional flow control valves
|
| ISO 10920-1997
| 气瓶 气瓶与瓶阀连接用25E锥螺纹 规范
| Gas cylinders - 25E taper thread for connection of valves to gas cylinders - Specification
|
| ISO 10933-1997
| 燃气分配系统用聚乙烯(PE)阀门
| Polyethylene (PE) valves for gas distribution systems
|
| ISO 11114-1-1997
| 移动气瓶 气瓶和瓶阀材料与盛装气体的相容性 第1部分:金属材料
| Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 1: Metallic materials
|
| ISO 11114-2-2000
| 移动气瓶 气瓶和瓶阀材料与盛装气体的相容性 第2部分:非金属材料
| Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials
|
| ISO 11114-3-1997
| 移动气瓶 气瓶和瓶阀材料与盛装气体的相容性 第3部分:氧环境中自燃试验
| Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 3: Autogenous ignition test in oxygen atmosphere
|
| ISO 11114-4-2005
| 移动气瓶.气瓶和瓶阀材料与盛装气体的相容性.第4部分:选择抗氢脆金属材料的试验方法
| Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 4: Test methods for selecting metallic materials resistant to hydrogen embrittlement
|
| ISO 11116-1-1999
| 气瓶 气瓶与瓶阀连接用17E锥螺纹 第1部分:规范
| Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 1: Specification
|
| ISO 11116-2-1999
| 气瓶 气瓶与瓶阀连接用17E锥螺纹 第2部分:检验量规
| Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 2: Inspection gauges
|
| ISO 11191-1997
| 气瓶 气瓶与瓶阀连接用25E锥螺纹 检验量规
| Gas cylinders - 25E taper thread for connection of valves to gas cylinders - Inspection gauges
|
| ISO 11419-1997
| 农业灌溉设备 浮子式空气释放阀
| Agricultural irrigation equipment - Float type air release valves
|
| ISO 11727-1999
| 气压传动 控制阀和其他元件的气口控制机构的标识
| Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components
|
| ISO 11929-1-2000
| 电离辐射测量探测限和判断阀的确定 第1部分:基本原则及对不经过样品处理的计数测量的应用
| Determination of the detection limit and decision threshold for ionizing radiation measurements - Part 1: Fundamentals and application to counting measurements without the influence of sample treatment
|
| ISO 11929-2-2000
| 电离辐射测量探测限和判断阀的确定 第2部分:基本原则及对经过样品处理的计数测量的应用
| Determination of the detection limit and decision threshold for ionizing radiation measurements - Part 2: Fundamentals and application to counting measurements with the influence of sample treatment
|
| ISO 11929-3-2000
| 电离辐射测量探测限和判断阀的确定 第3部分:基本原则及对不经过样品处理的高分辨率γ能谱法计数测量的应用
| Determination of the detection limit and decision threshold for ionizing radiation measurements - Part 3: Fundamentals and application to counting measurements by high resolution gamma spectrometry, without the influence of sample treatment
|
| ISO 11929-7-2005
| 电离辐射测量探测限和判断阀的确定.第7部分:基本原则和一般应用
| Determination of the detection limit and decision threshold for ionizing radiation measurements - Part 7: Fundamentals and general applications
|
| ISO 11933-4-2001
| 密封箱室部件 第4部分：通风和气体清洁系统，诸如：过滤器、捕获器、安全和调节阀、控制和保护器件
| Components for containment enclosures - Part 4: Ventilation and gas-cleaning systems such as filters, traps, safety and regulation valves, control and protection devices
|
| ISO 12149-1999
| 螺栓连接阀盖的通用钢制截止阀
| Bolted bonnet steel globe valves for general-purpose applications
|
| ISO 12209-1-2000
| 气瓶 压缩可呼吸空气用气瓶阀的放气连接器 第1部分:轭型连接器
| Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air - Part 1: Yoke type connections
|
| ISO 12209-2-2000
| 气瓶 压缩可呼吸空气用气瓶阀的放气连接器 第2部分:螺纹式连接器
| Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air - Part 2: Threaded connections
|
| ISO 12209-3-2000
| 气瓶 压缩可呼吸空气用气瓶阀的放气连接器 第3部分:230巴阀适配器
| Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air - Part 3: Adaptor for 230 bar valves
|
| ISO 12238-2001
| 气压传动 方向控制阀 移动时间的测量
| Pneumatic fluid power - Directional control valves - Measurement of shifting time
|
| ISO 13340-2001
| 可搬运输汽缸 不可再充气汽缸阀 规范和原机试验
| Transportable gas cylinders - Cylinder valves for non-refillable cylinders - Specification and prototype testing
|
| ISO 13341 Technical Corrigendum 1-1998
| 移动气瓶 气瓶阀的装配 技术勘误1
| Transportable gas cylinders - Fitting of valves to gas cylinders; Technical Corrigendum 1
|
| ISO 13341-1997
| 移动气瓶 气瓶阀的装配
| Transportable gas cylinders - Fitting of valves to gas cylinders
|
| ISO 13758-1996
| 液化石油气 评价丙烷干燥度 阀冻结法
| Liquefied petroleum gases - Assessment of the dryness of propane - Valve freeze method
|
| ISO 14245-2006
| 气瓶.液化石油气瓶阀门的规范和试验.自闭合
| Gas cylinders - Specifications and testing of LPG cylinder valves - Self-closing
|
| ISO 14246-2001
| 可搬运的储气罐 储气罐阀 制造试验和检验
| Transportable gas cylinders - Gas cylinder valves - Manufacturing tests and inspections
|
| ISO 14313-1999
| 石油和天然气工业 管道输送系统 管道阀
| Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves
|
| ISO 14617-8-2002
| 图表用图形符号.第8部分:阀门和气流调节器
| Graphical symbols for diagrams - Part 8: Valves and dampers
|
| ISO 14723-2001
| 石油和天然气工业 管道输送系统 海底管道阀
| Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves
|
| ISO 14960-2004
| 无内胎轮胎.气阀和部件.试验方法
| Tubeless tyres - Valves and components - Test methods
|
| ISO 15218-2003
| 气压传动.3/2电磁阀.安装接口表面
| Pneumatic fluid power - 3/2 solenoid valves - Mounting interface surfaces
|
| ISO 15245-1-2001
| 气瓶 阀与气瓶连接的平行螺纹 第1部分：规范
| Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 1: Specification
|
| ISO 15245-2-2001
| 气瓶 阀与气瓶连接的平行螺纹 第2部分：量规检验
| Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 2: Gauge inspection
|
| ISO 15364-2000
| 船舶与海上技术 散货船真空/压力阀
| Ships and marine technology - Pressure/vacuum valves for cargo tanks
|
| ISO 15407-1-2000
| 气压传动 五气口方向控制阀、规格18mm和26mm 第1部分:不带电接头的安装面
| Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 1: Mounting interface surfaces without electrical connector
|
| ISO 15407-2-2003
| 气压传动.五气口方向控制阀,规格18mm和26mm.第2部分:可任选连接器的安装接口
| Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 2: Mounting interface surfaces with optional electrical connector
|
| ISO 15500-12-2001
| 道路车辆 压缩天然气(CNG)燃料系统部件 第12部分:减压阀
| Road vehicles - Compressed natural gas (CNG) fuel system components - Part 12: Pressure relief valve (PRV)
|
| ISO 15500-14-2002
| 道路车辆.压缩天然气(CNG)燃料系统部件.第14部分:溢流阀
| Road vehicles - Compressed natural gas (CNG) fuel system components - Part 14: Excess flow valve
|
| ISO 15500-3-2001
| 道路车辆 压缩天然气(CNG)燃料系统部件 第3部分:防逆阀
| Road vehicles - Compressed natural gas (CNG) fuel system components - Part 3: Check valve
|
| ISO 15500-4-2001
| 道路车辆 压缩天然气(CNG)燃料系统部件 第4部分:控阀
| Road vehicles - Compressed natural gas (CNG) fuel system components - Part 4: Manual valve
|
| ISO 15500-5-2001
| 道路车辆 压缩天然气(CNG)燃料系统部件 第5部分:手控气缸阀
| Road vehicles - Compressed natural gas (CNG) fuel system components - Part 5: Manual cylinder valve
|
| ISO 15500-6-2001
| 道路车辆 压缩天然气(CNG)燃料系统部件 第6部分:自动阀
| Road vehicles - Compressed natural gas (CNG) fuel system components - Part 6: Automatic valve
|
| ISO 15665 Technical Corrigendum 1-2004
| 声学.管道、阀门和法兰的隔音.技术勘误1
| Acoustics - Acoustic insulation for pipes, valves and flanges; Technical Corrigendum 1
|
| ISO 15665-2003
| 声学.管、阀和法兰隔声
| Acoustics - Acoustic insulation for pipes, valves and flanges
|
| ISO 15761-2002
| 石油和天然气工业用尺寸为DN 100及更小的钢闸阀、球阀和止回阀
| Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries
|
| ISO 15848-1-2006
| 工业阀.漏气的测量、试验和鉴定程序.第1部分:阀门定型试验的分类系统和鉴定程序
| Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves
|
| ISO 15995-2006
| 气瓶.液化石油气瓶阀门的规范和试验.手工操作
| Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated
|
| ISO 15996-2005
| 储气瓶.剩余压力阀.一般要求和型式试验
| Gas cylinders - Residual pressure valves - General requirements and type testing
|
| ISO 16135-2006
| 工业阀.热塑性材料的球阀
| Industrial valves - Ball valves of thermoplastics materials
|
| ISO 16136-2006
| 工业阀.热塑性材料的蝶阀
| Industrial valves - Butterfly valves of thermoplastics materials
|
| ISO 16137-2006
| 工业阀.热塑性材料的止回阀
| Industrial valves - Check valves of thermoplastics materials
|
| ISO 16138-2006
| 工业阀.热塑性材料的隔膜阀
| Industrial valves - Diaphragm valves of thermoplastics materials
|
| ISO 16139-2006
| 工业阀.热塑性材料的门阀
| Industrial valves - Gate valves of thermoplastics materials
|
| ISO 17082-2004
| 气压传动.阀.供货商文献中的数据
| Pneumatic fluid power - Valves - Data to be included in supplier literature
|
| ISO 17292-2004
| 石油、石化和相关工业用金属球阀
| Metal ball valves for petroleum, petrochemical and allied industries
|
| ISO 20401 Technical Corrigendum 1-2005
| 气动液压驱动系统.方向控制阀.直径在8mm到12mm的圆形电连接器管脚分布的规范.技术勘误1
| Pneumatic fluid power systems - Directional control valves - Specification of pin assignment for electrical round connectors of diameters 8 mm and 12 mm; Technical Corrigendum 1
|
| ISO 20401-2005
| 气动液压驱动系统.方向控制阀.直径在8mm到12mm的圆形电连接器管脚分布的规范
| Pneumatic fluid power systems - Directional control valves - Specification of pin assignment for electrical round connectors of diameters 8 mm and 12 mm
|
| ISO 21787-2006
| 工业阀.热塑性材料的球形阀
| Industrial valves - Globe valves of thermoplastics materials
|
| ISO 2290-1972
| 旋转钻井设备.方钻杆上旋阀和下旋阀
| Rotary drilling equipment; Upper and lower Kelly cocks
|
| ISO 23551-1-2006
| 气体燃烧器和燃气设备用安全和控制装置.特殊要求.第1部分:自动阀门
| Safety and control devices for gas burners and gas-burning appliances - Particular requirements - Part 1: Automatic valves |
| ISO 23551-4-2005
| 气体燃烧器和燃气设备用安全和控制设备.特殊要求.第4部分:自动截止阀的阀门检验系统
| Safety and control devices for gas burners and gas-burning appliances - Particular requirements - Part 4: Valve-proving systems for automatic shut-off valves
|
| ISO 3822-2-1995
| 声学 供水设施的装置和设备发射的噪声的实验室测试 第2部分:放水龙头和混合阀的安装和工作条件
| Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 2: Mounting and operating conditions for draw-off taps and mixing valves
|
| ISO 3822-3-1997
| 声学 供水设施的装置和设备发射的噪声的实验室测试 第3部分:管路阀门和器件的安装和工作条作
| Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 3: Mounting and operating conditions for in-line valves and appliances
|
| ISO 407-2004
| 小型医用气瓶.针导轭式阀连接
| Small medical gas cylinders - Pin-index yoke-type valve connections
|
| ISO 4126-1-2004
| 过压保护安全设备.第1部分:安全阀
| Safety devices for protection against excessive pressure - Part 1: Safety valves
|
| ISO 4126-3-2006
| 过压保护安全设备.第3部分:组合中防爆板安全设备和安全阀门
| Safety devices for protection against excessive pressure - Part 3: Safety valves and bursting disc safety devices in combination
|
| ISO 4126-4-2004
| 过压保护安全设备.第4部分:液压控制安全阀
| Safety devices for protection against excessive pressure - Part 4: Pilot-operated safety valves
|
| ISO 4401-2005
| 液压传动.四油口定向控制阀.装配面
| Hydraulic fluid power - Four-port directional control valves - Mounting surfaces
|
| ISO 4411-1986
| 液压传动 阀 压差/流量特性的测定
| Hydraulic fluid power; Valves; Determination of pressure differential/flow characteristics
|
| ISO 4422-4-1997
| 给水用硬聚氯乙烯(PVC-U)管材和管件 规范 第4部分:阀及辅助设备
| Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 4: Valves and ancillary equipment
|
| ISO 4548-2-1997
| 内燃机全流式机油滤清器试验方法 第2部分:滤芯旁通阀特性
| Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 2: Element by-pass valve characteristics
|
| ISO 4548-9-1995
| 内燃机全流式机油滤清器试验方法 第9部分:进、出口止回阀试验
| Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 9: Inlet and outlet anti-drain valve tests
|
| ISO 5135-1997
| 声学 在混响室中测定空调终端设备、空调终端单元、阻尼器和调节阀门的噪声功率级
| Acoustics - Determination of sound power levels of noise from air-terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room
|
| ISO 5145 AMD 1-2006
| 气体和混合气体气瓶阀出气口.选择和尺寸.修改件1：医用气体气瓶瓶阀出气口
| Cylinder valve outlets for gases and gas mixtures - Selection and dimensioning; Amendment 1: Cylinder valve outles for gases for medical use
|
| ISO 5145-2004
| 气体和混合气体气瓶瓶阀出气口.选择和尺寸
| Cylinder valve outlets for gases and gas mixtures - Selection and dimensioning
|
| ISO 5208-1993
| 通用阀门 阀门的压力试验
| Industrial valves; pressure testing of valves
|
| ISO 5209-1977
| 通用阀门 标志
| General purpose industrial valves; Marking
|
| ISO 5210-1991
| 通用阀门 多回转阀门驱动装置的连接
| Industrial valves; multi-turn valve actuator attachments
|
| ISO 5211-2001
| 工业阀门.部分回转阀门致动器附件
| Industrial valves - Part-turn actuator attachment
|
| ISO 5599-1-2001
| 气压传动 五气口方向控制阀 第1部分:不带电接头的安装面
| Pneumatic fluid power - Five-port directional control valves - Part 1: Mounting interface surfaces without electrical connector
|
| ISO 5599-2 AMD 1-2004
| 气压传动.五气口方向控制阀.第2部分:带可选电接头的安装面.修改件1
| Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector; Amendment 1
|
| ISO 5599-2-2001
| 气压传动 五气口方向控制阀 第2部分:带可选电接头的安装面
| Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector
|
| ISO 5599-3-1990
| 气压传动 五气口方向控制阀 第3部分:表示阀功能的标注方法
| Pneumatic fluid power; five-port directional control valves; part 3: code system for communication of valve functions
|
| ISO 5781-2000
| 液压传动 压力控制阀(不包括溢流阀)、顺序阀、卸荷阀、节流阀和单向阀 安装面
| Hydraulic fluid power - Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces
|
| ISO 5783-1995
| 液压传动 阀安装面和插装阀孔的标识规则
| Hydraulic fluid power - Code for identification of valve mounting surfaces and cartridge valve cavities
|
| ISO 5996-1984
| 铸铁闸阀
| Cast iron gate valves
|
| ISO 6002-1992
| 用螺栓连接阀盖的钢制闸阀
| Bolted bonnet steel gate valves
|
| ISO 6182-2-2005
| 消防.自动喷水灭火系统.第2部分:湿式报警阀、延迟器和水务警铃的要求和试验方法
| Fire protection - Automatic sprinkler systems - Part 2: Requirements and test methods for wet alarm valves, retard chambers and water motor alarms
|
| ISO 6182-3-2005
| 消防.自动喷水灭火系统.第3部分:干式阀的要求和试验方法
| Fire protection - Automatic sprinkler systems - Part 3: Requirements and test methods for dry pipe valves
|
| ISO 6182-5-2006
| 消防.自动喷水灭火系统.第5部分:雨淋阀的要求和试验方法
| Fire protection - Automatic sprinkler systems - Part 5: Requirements and test methods for deluge valves
|
| ISO 6182-6-2006
| 消防.自动喷水灭火系统.第6部分:止回阀的要求和试验方法
| Fire protection - Automatic sprinkler systems - Part 6: Requirements and test methods for check valves
|
| ISO 6182-8-2006
| 消防.自动喷水灭火系统.第8部分:预动干式报警阀的要求和试验方法
| Fire protection - Automatic sprinkler systems - Part 8: Requirements and test methods for pre-action dry alarm valves
|
| ISO 6263-1997
| 液压传动 调速阀 安装面
| Hydraulic fluid power - Compensated flow-control valves - Mounting surfaces
|
| ISO 6264-1998
| 液压传动 溢流阀 安装面
| Hydraulic fluid power - Pressure-relief valves - Mounting surfaces
|
| ISO 6403-1988
| 液压传动 控制流量及压力的阀 试验方法
| Hydraulic fluid power; valves controlling flow and pressure; test methods
|
| ISO 6552-1980
| 自动蒸气疏水阀 术语定义
| Automatic steam traps; Definition of technical terms
|
| ISO 6553-1980
| 自动蒸气疏水阀 标志
| Automatic steam traps; Marking
|
| ISO 6554-1980
| 法兰连接自动蒸气疏水阀 结构长度
| Flanged automatic steam traps; Face-to-face dimensions
|
| ISO 6704-1982
| 自动蒸气疏水阀 分类
| Automatic steam traps; Classification
|
| ISO 683-15-1992
| 热处理钢、合金钢和易切钢 第15部分:内燃机用阀门钢
| Heat-treatable steels, alloy steels and free-cutting steels; part 15: valve steels for internal combustion engines
|
| ISO 6948-1981
| 自动蒸气疏水阀 产品试验和工作特性试验
| Automatic steam traps; Production and performance characteristic tests
|
| ISO 6953-1 Technical Corrigendum 1-2006
| 气压传动.压缩空气调压阀和带过滤器的调压阀.第1部分:商务文件中包含的主要特性和产品标识要求.技术勘误1
| Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 1: Main characteristics to be included in literature from suppliers and product-marking requirements; Technical Corrigendum 1
|
| ISO 6953-1-2000
| 气压传动 压缩空气调压阀和带过滤器的调压阀 第1部分:商务文件中包含的主要特性和产品标识要求
| Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 1: Main characteristics to be included in literature from suppliers and product-marketing requirements
|
| ISO 6953-2-2000
| 气压传动 压缩空气调压阀和带过滤器的调压阀 第2部分:评定商务文件中包含的主要特性的试验方法
| Pneumatic fluid power - Compressed air pressure regulators and filter-regulators - Part 2: Test methods to determine the main characteristics to be included in literature from suppliers
|
| ISO 7121-2006
| 工业通用钢制球阀
| Steel ball valves for general-purpose industrial applications
|
| ISO 7244-1984
| 空气配给和空气扩散 风门和阀门的空气动力试验
| Air distribution and air diffusion; Aerodynamic testing of dampers and valves
|
| ISO 7259-1988
| 地下用的按钮操纵的铸铁闸阀
| Predominantly key-operated cast iron gate valves for underground use
|
| ISO 7289-1996
| 气焊、切割及相关工艺用带关闭阀的快速接头
| Quick-action couplings with shut-off valves for gas welding, cutting and allied processes
|
| ISO 7349-1983
| 热塑性塑料阀门 连接参数
| Thermoplastics valves; Connection references
|
| ISO 7368-1989
| 液压传动 二油口盖板式插装阀 插装孔
| Hydraulic fluid power; two-port slip-in cartridge valves; cavities
|
| ISO 7508-1985
| 承压管用硬聚氯乙烯(PVC-U)阀门 基本尺寸 公制系列
| Unplasticized polyvinyl chloride (PVC-U) valves for pipes under pressure; Basic dimensions; Metric series
|
| ISO 7714-2000
| 农业灌溉设备 容量阀 一般要求和试验方法
| Agricultural irrigation equipment - Volumetric valves - General requirements and test methods
|
| ISO 7789 Technical Corrigendum 1-1999
| 液压传动 二油口、三油口和四油口螺纹式插装阀 插装孔 技术勘误1
| Hydraulic fluid power - Two-, three- and four-port screw-in cartridge valves - Cavities; Technical Corrigendum 1
|
| ISO 7789-1998
| 液压传动 二油口、三油口和四油口螺纹式插装阀 插装孔
| Hydraulic fluid power - Two-, three- and four-port screw-in cartridge valves - Cavities
|
| ISO 7790-1997
| 液压传动 四油口叠加阀和四油口方向控制阀02、03和05规格 夹紧尺寸
| Hydraulic fluid power - Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 - Clamping dimensions
|
| ISO 7841-1988
| 自动蒸气疏水阀 漏气量的测定 试验方法
| Automatic steam traps; determination of steam loss; test methods
|
| ISO 7842-1988
| 自动蒸气疏水阀 排水量测定 试验方法
| Automatic steam traps; determination of discharge capacity; test methods
|
| ISO 8233-1988
| 热塑性塑料阀门 扭矩 试验方法
| Thermoplastics valves; torque; test method
|
| ISO 8242-1989
| 受压管用聚丙烯(PP)阀门 基本尺寸 公制系列
| Polypropylene (PP) valves for pipes under pressure; basic dimensions; metric series
|
| ISO 8659-1989
| 热塑性塑料阀门 疲劳强度 试验方法
| Thermoplastics valves; fatigue strength; test method
|
| ISO 9393-1-2004
| 工业用热塑性阀门.压力试验方法和要求.第1部分:总则
| Thermoplastics valves for industrial applications - Pressure test methods and requirements - Part 1: General
|
| ISO 9393-2-2005
| 工业用热塑性阀门.压力试验方法和要求.第2部分:试验条件和基本要求
| Thermoplastics valves for industrial applications - Pressure test methods and requirements - Part 2: Test conditions and basic requirements
|
| ISO 9461-1992
| 液压传动 阀的油口、底板、控制装置和电磁铁的标准
| Hydraulic fluid power; identification of valve ports, subplates, control devices and solenoids
|
| ISO 9635-1990
| 灌溉设备 液压操纵灌溉阀
| Irrigation equipment; hydraulically operated irrigation valves
|
| ISO 9644 AMD 1-1998
| 农业灌溉设备 灌溉阀压力损失 试验方法 修改1
| Agricultural irrigation equipment - Pressure losses in irrigation valves - Test method; Amendment 1
|
| ISO 9644-1993
| 农业灌溉设备 灌溉阀压力损失 试验方法
| Agricultural irrigation equipment; pressure losses in irrigation valves; test method
|
| ISO 9817-1991
| 乘用车 发动机冷却系统 注水口上的带限压阀加水口盖及其斜面座的尺寸
| Passenger cars; engine cooling systems; dimensions of pressure caps and their ramp seats on filler necks
|
| ISO 9818-1991
| 乘用车 发动机冷却系统 带限压阀加水口盖的试验方法和标志
| Passenger cars; engine cooling systems; test methods and marking of pressure caps
|
| ISO 9911-1993
| 农业灌溉设备 手工操作小型塑料阀门
| Agricultural irrigation equipment; manually operated small plastics valves
|
| ISO 9952-1993
| 农业灌溉设备 止回阀
| Agricultural irrigation equipment; check valves
|
| ISO/TR 7470-1988
| 气瓶阀出气口 标准或实际使用的一览表
| Valve outlets for gas cylinders; list of provisions which are either standardized or in use
|
| 编号 | 中文名称 | 英文名称 |
|---|