编号 | 中文名称 | 英文名称 |
NF A32-060-2001
| 铸造产品.泵、阀门和配件用铸钢件和镍合金铸件(内部部件和防护壳体)
| (Foundry products - Cast steel and nickel alloy castings for pumps, valves and fittings (enclosures and internal components).)
|
NF A72-115-1966
| 高炉附件.热风阀.阀盖和底座(PN6)
| (BLAST FURNACE ACCESSORIES. HOT AIR VALVES. DISCS AND SEATS,PN 6.)
|
NF A72-120-1973
| 钢铁厂.气体管道和大直径阀.带法兰的接头(PN6)
| (LARGE DIAMETER PIPES AND VALVES FOR GASEOUS FLUIDS. FLANGE CONNECTIONS PN 6.)
|
NF A84-330-1982
| 气焊设备.乙炔发生器用“防回气—断火”的液压安全阀和组合装置.规范和试验
| (GAS WELDING EQUIPMENT. HYDRAULIC SAFETY SEALS AND COMBINED “NON-RETURN VALVE/FLAME ARRESTOR“ DEVICES FOR ACETYLENE GENERATORS. REQUIREMENTS AND TESTS.)
|
NF A84-420-1991
| 气焊设备和有关方法.减压阀入品接头.尺寸
| (Equipment for gas welding and allied processes. Pressure regulators inlet connections. Dimensions.)
|
NF A84-621-2002
| 气焊设备.焊接、切割和相关工艺用带截止阀的速动连接
| (Gas welding equipment - Quick-action coupling with shut-off valves for welding, cutting and allied processes.)
|
NF B35-792-2003
| 实验室用旋塞和阀门的颜色编码
| (Colour coding of taps and valves for use in laboratories.)
|
NF B51-078-1-2001
| 木基板.结构设计的特性阀门.第1部分:OSB.颗粒板和纤维板
| (Wood-based panels - Characteristic values for structural design - Part 1 : OSB, particleboards and fiberboards.)
|
NF C46-500-2002
| 工业过程控制系统.带气压输出的阀位控制器性能评估方法
| (Industrial-process control systems - Methods of evaluating the performance of valve positioners with pneumatic outputs.)
|
NF C46-502-1993
| 工业过程用调节阀.第1部分:术语和概论
| (Industrial-process control valves. Part 1 : control valve terminology and general considerations.)
|
NF C46-503-1999
| 工业过程调节阀.第2-1部分:流量.在安装条件下液体流量的截面方程
| (Industrial-process control valves. Part 2-1 : flow capacity. Sizing equations for fluid flow under installed conditions.)
|
NF C46-505-1998
| 绝缘过程控制阀.第2-3部分:流量容量.试验过程
| (Industrial-process control valves. Part 2-3 : flow capacity. Test procedures.)
|
NF C46-506-1990
| 工业过程用调节阀.流量.流量的特性和校正的固有系数
| (Industrial-process control valves. Flow capacity. Inherent flow characteristics and rangeability.)
|
NF C46-510-2001
| 工业过程控制阀.第3-1部分:尺寸.双通球型直立式控制法兰阀门的面对面尺寸和双通球型角度控制法兰阀门的中心
| (Industrial-process control valves - Part 3-1 : dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, a)
|
NF C46-511-2001
| 工业过程控制阀.第3-2部分:尺寸.蝶阀除外的旋转控制阀门的面对面尺寸
| (Industrial-process control valves - Part 3-2 : dimensions - Face-to-face dimensions for rotary control valves except butterfly valves.)
|
NF C46-512-1999
| 工业处理控制阀.第3-3部分:尺寸.对焊接的头尾相接尺寸.两接头球型直接式控制阀(欧洲标准EN 60534-3-3)
| (Industrial-process control valves. Part 3-3 : dimensions. End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves.)
|
NF C46-519-2001
| 工业过程控制阀.第8部分:噪声考虑.第1节:实验室测量气动流经控制阀产生的噪声
| (Industrial-process control valves - Part 8 : noise considerations - Section 1 : laboratory measurement of noise generated by aerodynamic flow through control valves.)
|
NF C46-520-1993
| 工业过程控制阀.第8部分:噪声问题.第2节:通过控制阀的液压流动产生的噪声的实验室测量
| (Industrial-process control valves. Part 8 : noise considerations. Section 2 : laboratory measurement of noise generated by hydrodynamic flow through control valves.)
|
NF C46-521-2001
| 工业过程控制阀.第8部分:噪声问题.第3节:气动控制阀噪声预测法
| (Industrial-process control valves - Part 8-3 : noise considerations - Control valves aerodynamic noise prediction method.)
|
NF C46-522-1994
| 工业处理控制阀.第8部分:噪声条款.第4节:液压流动产生的噪声预定(EN 534-8-4)
| (Industrial-process control valves. Part 8 : noise considerations. Section 4 : prediction of noise generated by hydrodynamic flow.)
|
NF C46-525-1991
| 工业过程用调节阀,调节阀门的限定栅屏
| (Industrial-process control valves. Control valve data sheet.)
|
NF C46-531-2001
| 工业过程控制阀.第6-2部分:定位器装到控制阀的安装细则.旋转传动装置上安装的定位器
| (Industrial-process control valves - Part 6-2 : mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators.)
|
NF C46-630-1998
| 工业过程控制阀.第6部分:控制阀与定位器连接用安装细节.第1节:线性传动装置上安装的定位器
| (Industrial-process control valves. Part 6 : mounting details for attachment of positioners to control valves. Section 1 : positioner mounting on linear actuators.)
|
NF C47-738-2002
| 家用和类似用途的电气自动控制器.第2-8部分:电动水阀的特殊要求,包括机械要求
| (Automatic electrical controls for household and similar use - Part 2-8 : particular requirements for electrically operated water valves, including mechanical requirements.)
|
NF C47-746/A2-2001
| 家用和类似用途自动电控制装置.第2部分:家用和类似用途漂浮型自动电气水阀操作控制的特殊要求
| (Automatic electrical controls for household and similar use - Part 2-16 : particular requirements for automatic electrical water level controls of the float type for household and similar applications)
|
NF C47-749-2002
| 家用和类似用途的电气自动控制器.第2-19部分:电气操作油阀门的特殊要求,包括机械要求
| (Automatic electrical controls for household and similar use - Part 2-19 : particular requirements for electrically operated oil valves, including mechanical requirements.)
|
NF C52-123-1968
| 变压器.介质液体的处理阀门
| (TRANSFORMERS. LIQUID DIELECTRIC DRAIN VALVES.)
|
NF C53-254/A1-2003
| 送电和配电系统用电力电子设备.静态无功功率补偿装置用晶闸管阀的试验
| (Power electronics for electrical transmission and distribution and systems - Testing of thyristor valves for static VAR compensators.)
|
NF C53-700-1-2002
| 高压直流(HVDC)电力传输用可控硅阀门.第1部分:电气试验
| (Thyristor valves for high voltage direct current (HVDC) power transmission - Part 1 : electrical testing.)
|
NF C53-700-1/A1-2003
| 高压直流电(HVDC)传输用晶闸管阀的试验.第1部分:电气试验
| (Testing of thyristor valves for high-voltage direct current (HVDC) transmission - Part 1 : electrical testing.)
|
NF C58-432-1996
| 固定铅酸蓄电池组.一般要求和试验方法.第2部分:阀门调节型
| (Stationary lead-acid batteries. General requirements and methods of test. Part 2 : valve regulated types.)
|
NF C58-561-2003
| 通用铅酸蓄电池组(阀门调节型).第1部分:一般要求、功能特性.试验方法
| (General purpose lead-acid batteries (valve-regulated types) - Part 1 : general requirements, functional characteristics - Methods of test.)
|
NF C58-562-2003
| 通用铅酸蓄电池组(阀门调节型).第2部分:尺寸、端子和标记
| (General purpose lead-acid batteries (valve-regulated types) - Part 2 : dimensions, terminals and marking.)
|
NF D11-121-1988
| 丙烯制家用浴缸.浴缸阀安装范围的补充规范
| (BATHS FOR DOMESTIC PURPOSES MADE OF ACRYLIC MATERIAL. ADDITIONAL SPECIFICATION FOR THE MOUNTING OF TAPS ON BATHS.)
|
NF D18-001-1965
| 卫生阀门.卫生设备用普通阀门.词汇
| (SANITARY TAPS. SINGLE TAP FOR SANITARY APPLIANCES. TERMINOLOGY.)
|
NF D18-201-1989
| 卫生设备管件.排放阀和混合阀的一般技术规范(公称尺寸1/2)PN 10.最低水压0.05MPa(0.5巴)
| (Sanitary tapware. General technical specifications for single taps and mixer taps (nominal size 1/2) pn 10. Minimum flow pressure of 0,05 MPa (0,5 bar).)
|
NF D18-202-1984
| 卫生阀门.缓冲器.一般技术规范
| (SANITARY TAPWARE. MECHANICAL MIXERS. GENERAL TECHNICAL SPECIFICATIONS.)
|
NF D18-203-1998
| 卫生阀门.静热混合阀门(PN10)一般技术规范(欧洲标准 EN 1111)
| (Sanitary tapware. Thermostatic mixing valves (PN 10). General technical specification.)
|
NF D18-205-1989
| 卫生阀门.淋浴设备的附件.一般技术规范
| (SANITARY TAPS. SHOWER ACCESSORIES. GENERAL TECHNICAL SPECIFICATIONS.)
|
NF D18-213-1996
| 卫生间管件.自动关闭阀PN 10
| (Sanitary tapware. Automatic shut-off valves pn 10.)
|
NF D18-216-2003
| 卫生洁具.压力冲洗阀和小便池自动关闭阀PN10
| (Sanitary tapware - Pressure flushing valves and automatic closing urinal valves PN 10.)
|
NF D36-306-2002
| 气体燃烧器和气体器具的自动关闭阀
| (Automatic shut-off valves for gas burners and gas appliances.)
|
NF D36-351-1969
| 家政学.使用气体燃料的灶具和洗衣机用的锥形转动阀门
| (TAPER TURNING COCKS FOR DOMESTIC COOKERS AND WASHING MACHINES USING GASEOUS FUELS.)
|
NF D36-380-2001
| 燃气燃烧器和燃气用具用自动截止阀的阀门检验系统
| (Valve proving systems for automatic shut-off valves for gas burners and gas appliances.)
|
NF D36-401-2000
| 建筑阀门.液压安全装置组.试验和要求
| (Building valves - Hydraulic safety groups - Tests and requirements.)
|
NF D36-402-2000
| 建筑阀门.膨胀组.试验和要求
| (Building valves - Expansion groups - Tests and requirements.)
|
NF D36-403-2000
| 建筑阀门.压力安全阀.试验和要求
| (Building valves - Pressure safety valves - Tests and requirements.)
|
NF D36-404-2000
| 建筑阀门.温度和压力组合安全阀.试验和要求
| (Building valves - Combined temperature and pressure relief valves - Tests and requirements.)
|
NF D36-405-2000
| 建筑阀门.膨胀阀.试验和要求
| (Building valves - Expansion valves - Tests and requirements.)
|
NF D36-406-2004
| 建筑物用阀.建筑物内饮用水给水用手动铜合金和不锈钢球阀.试验和要求
| (Building valves - Manually operated copper alloy and stainless steel ball valves for potable water supply in buildings - Tests and requirements.)
|
NF E29-003-1969
| 阀门关闭方向(闸板式阀门,阀式开关等)
| (DIRECTION OF CLOSURE FOR COCKS AND VALVES (SLUICE VALVES,SCREW DOWN VALVES,ETC.).)
|
NF E29-019-1985
| 工业阀门制造.可拆卸的栓接法兰盘.规范
| (Industrial valves. Threaded detachable flanges. Specifications.)
|
NF E29-064-1946
| 阀门制造.带活门的关闭阀.建筑物内阀门制造的专门术语
| (INDUSTRIAL VALVES. SCREW-DOWN STOPVALVES. TERMINOLOGY RELATING PARTICULARLY TO THE BUILDING TRADE.)
|
NF E29-065-1946
| 阀门制造.带活门的抽水阀门.建筑物内阀门制造的专门术语
| (INDUSTRIAL VALVES. TAPS. TERMINOLOGY RELATING PARTICULARLY TO THE BUILDING TRADE.)
|
NF E29-066-1946
| 阀门制造抽汲阀.转动式吸入阀和关闭阀.建筑物内阀门制造的专门术语
| (INDUSTRIAL VALVES. DRAW-OFF COCKS AND STOPCOCKS. TERMINOLOGY RELATING PARTICULARLY TO THE BUILDING TRADE.)
|
NF E29-134-1978
| 家用管道燃气设备用带节气阀并与阳端G1/2相连的双连式安全开关
| (SAFETY RELEASE DEVICES WITH BUILT-IN STOP TAP AND TWO G 1/2 MALE UNION CONNECTIONS FOR DOMESTIC APPLIANCES USING MAINS GAS FUELS.)
|
NF E29-138-1978
| 煤气用具控制用,锥形转动,有装配式铜管路带法兰和G1/2连接管节的角形墙壁阀
| (FLANGED WALL VALVES,AT RIGHT ANGLES,FOR CONTROLLING GAS APPLIANCES,WITH TAPERED ROTATING SECTION,FOR BUILT-IN BRASS PIPING AND WITH G 1/2 CONNECTION.)
|
NF E29-139-1998
| 建筑物气体装置用手工操作球阀和死底锥形旋塞
| (Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings.)
|
NF E29-161-1943
| 支流阀.关闭阀和给水阀.总则.公称压力.标准压力10
| (BRANCH PIPE VALVES. STOPCOCKS AND DRAW-OFF COCKS. GENERAL. NOMINAL PRESSURE PN 10.)
|
NF E29-162-1943
| 支流阀.关闭阀.公称压力,标准压力10
| (BRANCH PIPE VALVES. STOPCOCKS. NOMINAL PRESSURE PN 10.)
|
NF E29-163-1943
| 支流阀.给水阀.公称压力,标准压力10
| (BRANCH PIPE VALVES. DRAW-OFF COCKS. NOMINAL PRESSURE PN 10.)
|
NF E29-200-1-2002
| 法兰及其连接件.按PN标注的管、阀门、配件和附件用圆形法兰.钢法兰
| (Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1 : steel flanges.)
|
NF E29-200-4-2002
| 法兰及其连接件.按PN标注的管、阀门、配件和附件用圆形法兰.第4部分:铝合金法兰
| (Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4 : aluminium alloy flanges.)
|
NF E29-300-3-2003
| 阀门.外壳设计强度.第3部分:实验方法
| (Valves - Shell design strength - Part 3 : experimental method.)
|
NF E29-301-1-2000
| 工业阀门.对焊尾阀一端到另一端和中心到端面的尺寸
| (Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves.)
|
NF E29-302-1-1996
| 法兰管系统使用的金属阀.面至面和中心至面的尺寸.第1部分:PN-指定阀
| (Industrial valves. Face-to-face and centre-to-face dimensions of matal valves for use in flanged pipe systems. Part 1 : pn-designated valves.)
|
NF E29-303-1-2000
| 阀门.阀体、阀盖和阀套用材料.第1部分:欧洲标准中规定的钢
| (Valves - Materials for bodies, bonnets and covers - Part 1 : steels specified in European Standards.)
|
NF E29-303-2-2000
| 阀门.阀体、阀盖和阀套用材料.第2部分:欧洲标准中没有规定的钢
| (Valves - Materials for bodies, bonnets and covers - Part 2 : steels other than those specified in European Standards.)
|
NF E29-303-3-2000
| 阀门.阀体、阀盖和阀套用材料.第3部分:欧洲标准中规定的铸铁
| (Valves - Materials for bodies, bonnets and covers - Part 3 : cast iron specified in European Standards.)
|
NF E29-303-4-2003
| 阀门.阀体、阀盖和阀套用材料.第4部分:欧洲标准中规定的铜合金
| (Valves - Materials for bodies, bonnets and covers - Part 4 : copper alloys specified in European Standards.)
|
NF E29-305-1999
| 工业阀门.钢阀门对缝焊接末端.(欧洲标准EN 12627)
| (INDUSTRIAL VALVES. BUTT WELDING ENDS FOR STEEL VALVES. (EUROPEAN STANDARD EN 12627).)
|
NF E29-306-1-1995
| 阀.术语.第1部分:阀型的定义
| (Valves. Terminology. Part 1 : definition of types of valves.)
|
NF E29-306-2-1997
| 阀门.术语.第2部分:阀门元件的定义
| (VALVES. TERMINOLOGY. PART 2 : DEFINITION OF COMPONENTS OF VALVES. (EUROPEAN STANDARD EN 736-2).)
|
NF E29-306-3-1999
| 阀门.术语.第3部分:术语的定义
| (VALVES. TERMINOLOGY. PART 3 : DEFINITION OF TERMS. (EUROPEAN STANDARD EN 736-3).)
|
NF E29-306-3/A1-2001
| 阀门.术语.第3部分:术语定义
| (Valves - Terminology - Part 3 : definition of terms.)
|
NF E29-308-1985
| 工业阀门.技术规范和协调订货证明书样式
| (INDUSTRIAL VALVES. TECHNICAL SPECIFICATIONS AND CONFORMITY WITH ORDER ATTESTATION MODELS.)
|
NF E29-309-2001
| 工业阀门.操作元件尺寸控制的方法
| (Industrial valves - Method for sizing the operating element.)
|
NF E29-310-1992
| 通用工业阀的标记
| (Marking of general purpose industrial valves.)
|
NF E29-311-1-2003
| 工业阀门.阀门试验.第1部分:压力试验、试验程序和验收标准.强制性要求
| (Industrial valves - Testing of valves - Part 1 : pressure tests, test procedures and acceptance criteria - Mandatory requirements.)
|
NF E29-311-1982
| 阀门.阀门制造设备的工厂压力试验
| (Valves. Factory pressure testing for valves.)
|
NF E29-311-2-2003
| 工业阀门.阀门试验.第2部分:试验、试验程序和验收标准.补充标准
| (Industrial valves - Testing of valves - Part 2 : tests, test procedures and acceptance criteria - Supplementary criteria.)
|
NF E29-313-1990
| 工业阀门.阀门输送量的测定
| (Industrial valves. Determination of flow of valves. Case of compressible fluids.)
|
NF E29-314-1986
| 阀门.试验.术语.方法
| (VALVES. TESTS. NOMENCLATURE. METHODOLOGY.)
|
NF E29-316-1-2000
| 供水用阀门.适用性要求和专用检查试验.第1部分:一般要求
| (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 1 : general requirements.)
|
NF E29-316-2-2000
| 供水用阀门.适用性要求和专用检查试验.第2部分:隔离阀
| (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 2 : isolating valves.)
|
NF E29-316-3-2000
| 供水用阀门.适用性要求和专用检查试验.第3部分:止回阀
| (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 3 : check valves.)
|
NF E29-316-4-2000
| 供水阀门.特殊目的要求和适合验证试验的适配性. 第4部分:空气阀门
| (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 4 : air valves.)
|
NF E29-316-5-2001
| 供水用阀门.适用性要求和专用检查试验.第5部分:控制阀门
| (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5 : control valves.)
|
NF E29-317-1999
| 工业阀门.化工和石油化工加工工业阀门.要求和试验
| (Industrial valves - Valves for chemical and petrochemical process industry - Requirements and tests.)
|
NF E29-318-2000
| 工业阀门.LNG隔绝阀门.合适性和验证试验规范
| (Industrial valves - Isolating valves for LNG - Specification for suitability and appropriate verification tests.)
|
NF E29-319-2003
| 最大工作压力为16bar及以下的配气系统用阀.性能要求
| (Valves for gas distribution systems with maximum operating pressure less than or equal 16 bar - Performance requirements.)
|
NF E29-321-1999
| 阀门.用水作为试验液体的流动阻力试验
| (Valves - Test of flow resistance using water as test fluid.)
|
NF E29-330-2000
| 工业阀门.钢插板阀门
| (Industrial valves - Steel gate valves.)
|
NF E29-332-2003
| 工业用阀.铸铁闸阀
| (Industrial valves - Cast iron gate valves.)
|
NF E29-334-2003
| 工业用阀门.铜合金闸阀
| (Industrial valves - Copper alloy gate valves.)
|
NF E29-335-2003
| 石油和天然气工业用尺寸为DN 100及更小的钢闸阀、球阀和止回阀
| (Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries.)
|
NF E29-350-2003
| 工业用阀.钢制球阀、球状截止阀和止回阀
| (Industrial valves - Steel globe and globe stop and check valves.)
|
NF E29-354-2003
| 工业用阀.铸铁球阀
| (Industrial valves - Cast iron globe valves.)
|
NF E29-372-2001
| 工业阀门.铸铁止回阀
| (Industrial valves - Cast iron check valves.)
|
NF E29-373-1984
| 工业阀门.止回阀.钢制,单摇板式,带法兰盘,ISO标准压力16,20,25,40,50,100
| (Industrial valves. Flanged steel swing check valves. ISO PN A6, ISO PN 20, ISO PN 25, ISO PN 40, ISO PN 50, ISO PN 100.)
|
NF E29-382-1981
| 工业阀门.加压和放压的加厚部件
| (Industrial valves. Drain hoss or pressure tap.)
|
NF E29-383-1981
| 工业阀门.闸阀.旁路装置
| (Industrial valves. Gate valve. By-pass.)
|
NF E29-401-1996
| 工业阀门.多圈旋转阀门驱动器附件
| (Industrial valves. Multi-turn valve actuator attachments.)
|
NF E29-402-2001
| 工业阀门.部分回转阀门致动器附件
| (Industrial valves - Part-turn valve actuator attachments.)
|
NF E29-408-1992
| 工业用阀门.电力驱动器.规范
| (INDUSTRIAL VALVES. ELECTRIC ACTUATORS. SPECIFICATIONS.)
|
NF E29-409-1992
| 工业阀门.气动的和液压的促动器.规范
| (INDUSTRIAL VALVES. PNEUMATIC AND HYDRAULIC ACTUATORS. SPECIFICATIONS.)
|
NF E29-413-1989
| 工业阀门.安全阀流量计算.其他方法
| (INDUSTRIAL VALVE. SAFETY VALVES AND BURSTING DISC(S) DEVICES. CALCULATION OF THEORETICAL FLOWRATE.)
|
NF E29-414-1992
| 工业阀门.安全阀门.安全阀门类型S,G1,L1和L2流率计算示例
| (INDUSTRIAL VALVES. SAFETY VALVES. EXAMPLES FOR FLOWRATE CALCULATION OF SAFETY VALVES TYPES S,G1,L1 AND L2.)
|
NF E29-415-1990
| 工业阀门.安全阀.G平方型安全阀排出空气当量流量计算实例.GPL标准蓄水池的应用
| (INDUSTRIAL VALVES. SAFETY VALVES. CALCULATION OF AIR EQUIVALENT FLOW CAPACITY FOR SAFETY VALVES OF TYPE G2. APPLICATION FOR STANDARD VESSELS FOR GPL.)
|
NF E29-420-1985
| 工业阀门.安全阀.技术说明书样式和协调证明书
| (INDUSTRIAL VALVES. SAFETY AND RELIEF VALVES. MODEL OF TECHNICAL SPECIFICATIONS AND CONFORMITY CERTIFICATE.)
|
NF E29-421-1987
| 工业阀门.安全阀.安全膜.为获得工作特性的安装规范
| (Industrial valves. Safety valves. Bursting discs.)
|
NF E29-425-1987
| 工业阀门.防爆膜装置.定义.一般设计.试验.分类.标记.调节
| (Industrial valves. Bursting discs devices. Definitions. General design. Test. Classification. Marking. Conditioning.)
|
NF E29-430-1998
| 工业阀门.金属蝶型阀门
| (Industrial valves. Metallic butterfly valves.)
|
NF E29-440-1992
| 水蒸气自动排泄阀.分类.(欧洲标准 EN 26704)
| (Automatic steam traps. Classification.) |
NF E29-441-1992
| 水蒸气自动排泄阀.标记(欧洲标准EN26553)
| (Automatic steam traps. Marking.)
|
NF E29-443-1992
| 水蒸气自动排泄阀.产品试验和功能特性试验(欧洲标准 EN 26948)
| (Automatic steam traps. Production and performance characteristics tests.)
|
NF E29-445-1992
| 水蒸气自动排泄阀.流量测定.试验方法.(欧洲标准 EN 27842)
| (Automatic steam traps. Determination of discharge capacity. Test methods.)
|
NF E29-453-2000
| 工业过程控制阀门
| (Industrial process control valves.)
|
NF E29-465-1986
| 工业阀门.旋转阀.铜铝球阀.规范
| (INDUSTRIAL VALVES. CUPRO-ALUMINIUM BALL VALVES. SPECIFICATION.)
|
NF E29-466-1987
| 工业阀门.旋转阀.黄铜球阀.规范
| (INDUSTRIAL VALVES. BRASS BALL-VALVES. SPECIFICATIONS.)
|
NF E29-480-1994
| 地下热水管网的预隔热管道系统.钢制供水管道、聚氨基甲酸乙酯热绝缘材料及高密度聚乙烯外壳的钢阀门组件(欧
| (Preinsulated bonded pipe systems for underground hot water networks. Steelvalve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene.)
|
NF E29-492-2002
| 工业阀门.金属材料的薄片阀
| (Industrial valves - Diaphragm valves made of metallic materials.)
|
NF E29-648-1-1998
| 可运输储气瓶.储气瓶和阀门材料与气含量的相容性.第1部分:金属材料
| (Transportable gas cylinders. Compatibility of cylinder and valve materials with gas contents. Part 1 : metallic materials.)
|
NF E29-648-2-2001
| 可移动式液化气钢瓶.内有气体的钢瓶和阀材料的配合性.第2部分:非金属材料
| (Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2 : non-metallic materials.)
|
NF E29-648-3-1998
| 可运输气瓶.气瓶和含气阀门材料的可兼容性.第3部分:有氧环境中自燃试验
| (Transportable gas cylinders. Compatibility of cylinder and valve materials with gas contents. Part 3 : autogenous ignition test in oxygen atmosphere.)
|
NF E29-650-1992
| 气瓶.阀出口连接
| (Gas cylinders. Valve outlet connections.)
|
NF E29-661-1979
| 氯瓶上的锻钢阀门(最大容量60kg).公称压力25
| (FORGED-STEEL VALVES FOR CHLORINE CYLINDERS (MAX.CAPACITT 60 KG). NOMINAL PRESSURE PN 25.)
|
NF E29-662-1979
| 呼吸保护装置的压缩气瓶的阀门.使用压力200bar.尺寸特性.标记
| (VALVES FOR COMPRESSED AIR CYLINDERS FOR RESPIRATORY PROTECTIVE EQUIPMENT. SERVICE PRESSURE 200 BAR. DIMENSIONAL CHARACTERISTICS. MARKING.)
|
NF E29-663-1979
| 呼吸保护装置的压缩气瓶的阀门.使用压力300bar.尺寸特性.标记
| (VALUES FOR COMPRESSED AIR CYLINDERS FOR RESPIRATORY PROTECTIVE EQUIPMENT. SERVICE PRESSURE 300 BAR. DIMENSIONAL CHARACTER & STICS. MARKING.)
|
NF E29-664-1979
| 气瓶阀门出口.标准化提供的和使用中的装置对照表
| (VALVE OUTLETS FOR GAS CYLINDERS. LIST OF STANDARD PROVISIONS OR THOSE IN USE.)
|
NF E29-670-1998
| 可运输储气瓶.储气瓶阀门配件
| (Transportable gas cylinders. Fitting of valves to gas cylinders.)
|
NF E29-671-1981
| 气瓶.阀门装配锥体.总则
| (Gas cylinders. Taper screw thread for value stem and cylinder neck assembly. General.)
|
NF E29-672-1-1999
| 气瓶.气瓶阀门连接用17E锥螺纹.第1部分:规范
| (Gas cylinders. 17E taper thread for connection of valves to gas cylinders. Part 1 : specifications.)
|
NF E29-672-2-1999
| 气瓶.阀门与气瓶的连接用17E锥螺纹.第2部分:检验量规
| (Gas cylinders. 17E taper thread for connection of valves to gas cylinders. Part 2 : inspection gauges.)
|
NF E29-674-1-1996
| 可运输气瓶.阀与气瓶连接用25E锥形螺纹.第1部分:规范
| (Transportable gas cylinders. 25E taper thread for connection of valves to gas cylinders. Part 1 : specification.)
|
NF E29-674-2-1996
| 可运输气瓶.阀与气瓶连接用25E锥形螺纹.第2部分:量规检查
| (Transportable gas cylinders. 25E taper thread for connection of valves to gas cylinders. Part 2 : gauge inspection.)
|
NF E29-677-1981
| 气瓶.阀门装配锥体.公称直径28.3.锥度3/25.螺距1.814惠氏螺纹.检验规范
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER : 28,3. TAPER 3/25. 14 TPI SI. GAUGE REQUIREMENTS.)
|
NF E29-678-1980
| 气瓶.气瓶阀门颈装配螺纹锥体.公称直径16.4.锥度3/20.螺距14国际单位制
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 16,4,TAPER 3/20,14 TPI SI.)
|
NF E29-679-1981
| 气瓶.气瓶阀门颈装配锥体.公称直径16.4.锥度3/20.螺距14国际单位制.量规要求
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 16.4. TAPER 3/20. 14 TPI SI. GAUGE REQUIREMENTS.)
|
NF E29-680-1980
| 气瓶.阀杆和瓶颈组件用锥螺纹.公称直径25.8.锥度3/26(6°38`).螺距1.814国际单位制
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 25,8,TAPER 3/26 (6 DEGREES 38`,14 TPI SI)
|
NF E29-681-1981
| 气瓶.阀杆和瓶颈组件用锥螺纹.公称直径25.8.锥度3/26(6°C 38`).螺距1.814国际单位制.量规要求
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 25,8. TAPER 3/26 (6 DEGREES C 38`). 14 TP1 SI. GAUGE REQUIREMENTS.)
|
NF E29-682-1980
| 气瓶.阀杆和瓶颈组件用锥螺纹.公称直径34.锥度8.732%(5°).螺距为2国际单位制
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CULINDER NECK ASSEMBLY. NOMINAL DIAMETER 34 TAPER 8 732 PER CENT (5 DEGREES),PITCH 2 SI.)
|
NF E29-683-1981
| 气瓶.阀杆和瓶颈组件用锥螺纹.公称直径34.锥度8.736%(5°C).螺距为2国际单位制.量规要求
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 34. TAPER 8.736 PER CENT (5 DEGREES C). PITCH 2 SI. GAUGE ERQUIREMENTS.)
|
NF E29-684-1980
| 气瓶.阀杆和瓶颈组件用锥螺纹.公称直径26.锥度1/16(3°34`).螺距为1.814锥管螺纹
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 26,TAPER 1/16 (3 DEGREES 34`),14 TPI NPT.)
|
NF E29-685-1981
| 气瓶.阀杆和瓶颈组件用锥螺纹.公称直径26.锥度1/16(3°34`).螺距为1.814锥管螺纹.量规要求
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 26. TAPER 1/16 (3 DEGREES 34`). 14 TPI NPT. GAUGE REQUIREMENTS.)
|
NF E29-686-1-2002
| 储气瓶.连接储气瓶阀门的平行螺纹.第1部分:规范
| (Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 1: Specification.)
|
NF E29-686-2-2002
| 储气瓶.连接储气瓶阀门的平行螺纹.第2部分:量规检验
| (Gas cylinders - Parallel threads for correction of valves to gas cylinders - Part 2 : Gauge inspection.)
|
NF E29-690-1996
| 可运输气瓶.气瓶阀.规范和型式试验(EN 849)
| (Transportable gas cylinders. Cylinder valves. Specification and type testing.)
|
NF E29-690/A2-2001
| 可移动的燃气瓶.燃气瓶阀门.规范和型式试验
| (Transportable gas cylinders - Cylinder valves - Specification and type testing.)
|
NF E29-691-1996
| 可运输气瓶.工业和医用气瓶用阀保护帽和阀罩.设计,安装和试验
| (Transportable gas cylinders - Valve protection caps and valve guards for industrial and medical gas cylinders - Design, construction and tests.)
|
NF E29-691/A1-1999
| 可运输储气瓶.工业用和医用储气瓶用阀保护帽和阀护罩.设计、结构和试验
| (Transportable gas cylinders - Valve protection caps and valve guards for industrial and medical gas cylinders - Design, construction and tests.)
|
NF E29-691/A2-2000
| 便携式气瓶.工业和医用气瓶用阀门保护装置.设计,结构和试验
| (Transportable gas cylinders - Valve protection caps and valve guards for industrial and medical gas cylinders - Design, construction and tests.)
|
NF E29-692-1-2001
| 气瓶.微电子工业用气瓶阀接头.第1部分:输出口接头
| (Gas cylinders - Gas cylinder valve connections for use in the micro-electronics industry - Part 1 : outlet connections.)
|
NF E29-692-2-2001
| 气瓶.微电子工业用气瓶阀接头.第2部分:气瓶阀接头的规范和型式试验
| (Gas cylinders - Gas cylinder valve connections for use in the microelectronics industry - Part 2 : specification and type testing for valve to cylinder connections.)
|
NF E29-693-3-2001
| 气体钢瓶.压缩呼吸空气的气体钢瓶的出口连接.第3部分:230巴阀门适配器
| (Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air - Part 3 : adaptor for 230 bar valves.)
|
NF E29-694-2001
| 可运输气瓶.气瓶阀门.生产试验和检验
| (Transportable gas cylinders - Gas cylinder valves - Manufacturing tests and inspections.)
|
NF E29-695-2001
| 可运输气瓶.不可再充填的气瓶用阀门.规范和原型试验
| (Transportable gas cylinders - Cylinders valves for non-refillable cylinders - Specification and prototype testing.)
|
NF E29-790-2003
| 便携式燃具用带或不带阀门的一次性使用液化石油气金属气瓶.制造、检验、试验和标记
| (Non-refillable metallic gas cartridges for liquefied petroleum gases, with or without a valve, for use with portable appliances - Construction, inspection, testing and marking.)
|
NF E29-796-2003
| 可运输储气瓶.储气瓶定期检查时气瓶阀的检查和维修
| (Transportable gas cylinders - Inspection and maintenance of cylinder valves at time of periodic inspection of gas cylinders.)
|
NF E31-330-1-2000
| 燃油锅炉用供油系统的安装. 第1部分:安全要求和试验.部件,进气阀控制和安全装置,供气油罐
| (Installations for oil supply systems for oil burners - Part 1: safety requirements and tests : parts, oil feed pumps, control and safety devices, supply tanks.)
|
NF E31-330-2-2000
| 燃油锅炉用供油系统的安装. 第2部分:安全要求和试验.部件,阀门, 管道,过滤器,油充气器,仪表
| (Installations for oil supply systems for oil burners - Part 2 : safety requirements and tests : parts, valves, pipes, filters, oil de-aerators, meters.)
|
NF E32-110-10-2002
| 水管锅炉和辅助设备.第10部分:防过压安全阀的要求
| (Water-tube boilers and auxiliary installations - Part 10 : requirements for safeguards against excessive pressure.)
|
NF E39-013-2003
| 区域供暖管道.直埋式热水供应网用预隔热连接的管道系统.聚氨酯隔热和聚乙烯外覆层进宅钢管用钢阀门组件
| (District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of pol)
|
NF E48-400-1996
| 液压传动.阀门装配面及盒式阀腔的识别标志
| (HYDRAULIC FLUID POWER. CODE FOR IDENTIFICATION OF VALVE MOUNTING SURFACES AND CARTRIDGE VALVE CAVITIES.)
|
NF E48-423-2001
| 液压传动.减压阀、顺序阀、卸载阀、节流阀和止回阀.装配面
| (Hydraulic fluid power - Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces.)
|
NF E48-432-1993
| 液压动力.4和5阀口伺服阀.安装面
| (HYDRAULIC FLUID POWER. POUR- AND FIVE-PORTS SERVOVALVES. MOUNTING SURFACES.)
|
NF E48-435-1998
| 液压传动.尺寸02、03和05的四端口模式排气阀和四端口方向控制阀.夹紧尺寸
| (Hydraulic fluid power. Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05. Clamping dimensions.)
|
NF E49-080-1-2002
| 气压液动.五通定向控制阀.第1部分:不带电连接器的安装接口
| (Pneumatic fluid power - Five-port directional control valves - Part 1 : mounting interfaces without electrical connector.)
|
NF E49-080-2-2002
| 气压液动.五通方向控制阀.第2部分:任选电气连接器的安装接口面
| (Pneumatic fluid power - Five-port directional control valves - Part 2 : mounting interface surfaces with optional electrical connector.)
|
NF E49-090-2-2003
| 气压传动.18mm和26mm五气口方向控制阀.第2部分:带光学电接头的安装面
| (Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 2 : mounting interfaces with optional electrical connector.)
|
NF E49-091-2002
| 气压传动.控制阀和其它部件的孔口和控制机械的验证
| (Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components.)
|
NF E49-093-2003
| 气压传动.3/2电磁阀.安装接口表面
| (Pneumatic fluid power - 3/2 solenoid valves - Mounting interface surfaces.)
|
NF E51-718-1998
| 建筑物通风.气体终端设备.调节器和阀门的动力学试验
| (Ventilation for buildings. Air terminal devices. Aerodynamic testing of dampers and valves.)
|
NF E86-507-1999
| 制冷容器.制冷装置阀(欧洲标准EN 1626)
| (Cryogenic vessels. Valves for cryogenic service.)
|
NF E86-512-1-2002
| 冷凝容器.防超压安全设施.第1部分:冷凝设备的安全阀
| (Cryogenic vessels - Safety devices for protection against excessive pressure - Part 1 : safety valves for cryogenic service.)
|
NF E87-010-1976
| 轮胎充气阀.术语
| (TYPE VALVES. TERMINOLOGY.)
|
NF F11-806-1996
| 铁路车辆.压缩空气电路用截止塞阀
| (RAILWAY ROLLING STOCK. SHUT-OFF PLUG VALVES, FOR COMPRESSED AIR CIRCUITS.)
|
NF H44-012-1986
| 烟雾发生器.气雾剂容器阀.18mm皮碗
| (Aerosols dispensers. Valves. Ferrule 18 mm.)
|
NF H44-013-1986
| 烟雾发生器.气雾剂容器阀.20mm皮碗
| (Aerosols dispensers. Valves. Ferrule 20 mm.)
|
NF H44-015-1986
| 烟雾发生器.气雾剂容器阀.15mm皮碗
| (Aerosols dispensers. Valves. Ferrule 15 mm.)
|
NF H44-020-1988
| 烟雾发生器.压力分配容器(气雾剂容器型).气雾剂容器上阀门的机械密封和安装的快速试验
| (AEROSOL DISPENSERS. RAPID TEST. TIGHTNESS OF VALVE MECHANISMS AND CLINCH.)
|
NF H44-028-1986
| 烟雾剂发生器.气雾剂阀.17mm皮碗
| (AEROSOLS DISPENSERS. VALVES. FERRULE 17 MM.)
|
NF H44-029-1986
| 烟雾剂发生器.气雾剂阀.13mm皮碗
| (AEROSOLS DISPENSERS. VALVES. FERRULE 13 MM.)
|
NF H44-030-1986
| 烟雾剂发生器.气雾剂阀.11mm皮碗
| (AEROSOLS DISPENSERS. VALVES. FERRULE 11 MM.)
|
NF J25-215-1969
| 造船工业.航海.船上阀门附件.杆的直径和螺纹
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. SHANK DIAMETERS AND THREADS.)
|
NF J25-220-1969
| 造船工业.航海.船上阀门附件.船首和手轮用方钢
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. SQUARES FOR STEMS AND HANDWHEELS.)
|
NF J25-255-1969
| 造船工业.航海.船上阀门附件.偏移手轮.尺寸.互换性
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. DISHED HANDWHEELS. DIMENSIONS. INTERCHANGEABILITY.)
|
NF J25-274-1969
| 造船工业.航海.船上阀门附件.板手
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. CRANK HANDLES.)
|
NF J25-308-1969
| 造船工业.船上阀门附件.填料箱.法兰压盖.尺寸.互换性
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. STUFFING BOXES. GLANDS WITH FLANGE. DIMENSIONS. INTERCHANGEABILITY.)
|
NF J25-310-1969
| 造船工业.航海.船上阀门附件.带压盖和螺母的填料箱
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. STUFFING BOXES WITH GLAND AND NUT.)
|
NF J25-500-1958
| 造船工业.海水专用阀门.一般规范
| (SHIPBUILDING. SEA WATER VALVES. GENERAL SPECIFICATION.)
|
NF J25-505-1958
| 造船工业.海水专用阀门.器材连接孔的位置
| (SHIPBUILDING. SEA WATER VALVES. ARRANGEMENT OF BODY ENDS.)
|
NF J25-510-1958
| 造船工业.海水专用阀门.带螺纹杆的连接阀.安装I.部件名称
| (SHIPBUILDING. SEA WATER VALVES. SCREW-DOWN STOP VALVES. PATTERN I. OPERATING MECHANISM. PARTS LIST.)
|
NF J25-513-1958
| 造船工业.海水专用阀门.自由滑动式连接阀,安装II.部件名称
| (SHIPBUILDING. SEA WATER VALVES. SHIP SIDE DISCHARGE VALVES. PATTERN II. OPERATING MECHANISM PARTS LIST.)
|
NF J25-516-1958
| 造船工业.海水专用阀门.闭锁式自由阀.安装III.部件名称
| (SHIPBUILDING. SEA WATER VALVES. SCREW-DOWN STOP-AND-CHECK VALVES. PATTERN III. OPERATING MECHANISM. PARTS LIST.)
|
NF J25-519-1958
| 造船工业.海水专用阀门.闭锁式自由阀门.安装IV.部件名称
| (SHIPBUILDING. SEA WATER VALVES. SCREW-DOWN STOP-AND-CHECK VALVES WITH OPENING MECHANISM. PATTERN IV. OPERATING MECHANISM PARTS LIST.)
|
NF J25-522-1958
| 造航工业.海水专用阀门.舱底吸水阀.组装件.一般尺寸
| (SHIPBUILDING. SEA WATER VALVES. BILGE VALVES. ASSEMBLY. GENERAL DIMENSIONS.)
|
NF J25-526-1958
| 造船工业.海水专用阀门.船弦排水阀.组装件.一般尺寸
| (SHIPBUILDING. SEA WATER VALVES. DISCHARGE VALVES. ASSEMBLY. GENERAL DIMENSIONS.)
|
NF J25-530-1958
| 造船工业.海水专用阀门.吸水收集箱.组装件.一般尺寸
| (SHIPBUILDING. SEA WATER VALVES. SUCTION MANIFOLD VALVES. ASSEMBLY. GENERAL DIMENSIONS.)
|
NF J25-535-1958
| 造船工业.海水专用阀门.压力收集箱.组装件.一般尺寸
| (SHIPBUILDING. SEA WATER VALVES. DELIVERY MANIFOLD VALVES. ASSEMBLY. GENERAL DIMENSIONS.)
|
NF J38-540-2002
| 船舶和造船技术.载油舱用压力/真空阀
| (Ships and marine technology - Pressure/vacuum valves for cargo tanks.)
|
NF J41-410-1957
| 造船工业.“金士顿“阀门.一般规范
| (SHIPBUILDING. KINGSTON VALVES. GENERAL SPECIFICATION.)
|
NF J41-415-1957
| 造船工业.“金士顿“阀门.总成.一般尺寸
| (SHIPBUILDING. KINGSTON VALVES. ASSEMBLY. GENERAL DIMENSIONS.)
|
NF J41-416-1957
| 造船工业.“金士顿“阀门.标称直径50-175号.部件名称
| (SHIPBUILDING. KINGSTON VALVES,NOMINAL BORE 50-175 MM. NOMENCLATURE OF PARTS.)
|
NF J41-417-1957
| 造船工业.“金士顿“阀门.标称直径200-500号.部件名称
| (SHIPBUILDING. KINGSTON VALVES,NOMINAL BORE 200-500 MM. NOMENCLATURE OF PARTS.)
|
NF J41-420-1957
| 造船工业.“金士顿“阀门.标称直径50-175号.阀体
| (SHIPBUILDING. KINGSTON VALVES,NOMINAL BORE 50-175 MM. BODY.)
|
NF J41-421-1957
| 造船工业.“金士顿“阀门.标称直径200-500号.阀体
| (SHIPBUILDING. KINGSTON VALVES,NOMINAL BORE 200-500 MM. BODY.)
|
NF J41-425-1957
| 造船工业.“金士顿“阀门.卡箍
| (SHIPBUILDING. KINGSTON VALVES. BONNET.)
|
NF J41-430-1957
| 造船工业.“金士顿“阀门.活门
| (SHIPBUILDING. KINGSTON VALVES. DISK.)
|
NF J41-435-1957
| 造船工业.“金士顿“阀门.阀体环座
| (SHIPBUILDING. KINGSTON VALVES. BODY SEAT RING.)
|
NF J41-440-1957
| 造船工业.“金士顿“阀门.阀杆
| (SHIPBUILDING. KINGSTON VALVES. STEM.)
|
NF J41-445-1957
| 造船工业.“金士顿“阀门.上导杆.螺母锁紧
| (SHIPBUILDING. KINGSTON VALVES. UPPER GUIDE. TAB WASHER.)
|
NF J41-446-1957
| 造船工业.“金士顿“阀门.下导杆
| (SHIPBUILDING. KINGSTON VALVES. LOWER GUIDE.)
|
NF J41-450-1957
| 造船工业.“金士顿“阀门.压力填圈.压盖和衬套
| (SHIPBUILDING. KINGSTON VALVES. STUFFING BOX,GLAND AND BUSHING.)
|
NF J41-455-1957
| 造船工业.“金士顿“阀门.手轮.套管
| (SHIPBUILDING. KINGSTON VALVES. HANDWHEEL. OPERATING SLEEVE.)
|
NF J41-460-1957
| 造船工业.“金士顿“阀门.止动帽
| (SHIPBUILDING. KINGSTON VALVES. LOCKING SHACKLE.)
|
NF J41-465-1957
| 造船工业.“金士顿“阀门.螺钉零件
| (SHIPBUILDING. KINGSTON VALVES. BOLTS AND SCREWS.)
|
NF J41-470-1957
| 造船式为.“金士顿“阀门.加工.调节
| (SHIPBUILDING. KINGSTON VALVES. MACHINING. FITS.)
|
NF J41-606-1993
| 造船工业.消防水管.消防阀门
| (SHIPBUILDING. FIRE HOSES. FIRE VALVES.)
|
NF J45-780-1953
| 造船工业.带自动阀的测量器.安装组件
| (SHIPBUILDING. SOUNDING PIPES WITH SELF-ACTING VALVE. INSTALLATION ASSEMBLY.)
|
NF J45-782-1953
| 造船工业.带自动阀的测量头.安装组件
| (SHIPBUILDING. HEAD OF SOUNDING PIPES WITH SELF-ACTING VALVE. MOUNTING ASSEMBLY.)
|
NF J45-784-1953
| 造船工业.带自动阀的测量头.盒子的零件
| (SHIPBUILDING. HEAD OF SOUNDING PIPES WITH SELF-ACTING VALVE. DETAILS OF BODY.)
|
NF J45-788-1953
| 造船工业.带自动阀的测量头.零件
| (SHIPBUILDING. HEAD OF SOUNDING PIPES WITH SELF-ACTING VALVE. DETAILS.)
|
NF J95-045-1998
| 小型船舶.船底阀和整个船体用配件.第1部分:金属的
| (Small craft. Seacoks and through-hull fittings. Part 1 : metallic.)
|
NF M41-016-1997
| 液化石油气.丙烷干燥评定.阀门冷冻法
| (LIQUEFIED PETROLEUM GASES. ASSESSMENT OF THE DRYNESS OF PROPANE. VALVE FREEZE METHOD. (EUROPEAN STANDARD EN ISO 13758).)
|
NF M62-301-4-2001
| 密封罩用组件.第4部分:通风和气体清洁系统(如:过滤器和疏水阀)的安全和调节阀门以及控制和保护装置
| (Components for containment enclosures - Part 4 : ventilation and gas-cleaning systems such as filters, traps, safety and regulation valves, control and protection devices.)
|
NF M87-213-2001
| 石油和天然气工业.下降孔设备.地下安全阀设备
| (Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment.)
|
NF M87-400-1984
| 石油工业.带外部杆和螺栓盖的钢制阀门.法兰或焊接端点ISOPN20.ISOPN420
| (Petroleum industry. Steel gate valves with-on flanges and joints. ISO PN 20 to ISO PN 420.)
|
NF M87-401-1985
| 石油工业.阀门试验和验收检查.耐压性能
| (Petroleum industry. Acceptance testing and inspection of valves. Performance under pressure.)
|
NF M87-402-1973
| 石油工业.带钢制法兰硬块密封物有斜座的阀门
| (PETROLEUM INDUSTRY. FLANGES AND SOLID WEDGE STEEL GATE-VALVES.)
|
NF M88-114-1982
| 罐车.液化气运输.4-40ba工作压力的DN50.DN80和DN100的止流和安全内部阀门
| (ROAD TANKERS. TRANSPORTATION OF LIQUEFIED GASES. INTERNAL STOP AND SAFETY OBTURATOR. NOMINAL DIAMETERS DN 50,DN 80 AND DN 100 FOR SERVICE PRESSURE BETWEEN 4 BAR AND 40 BAR.)
|
NF M88-125-2001
| 危险货物运输罐.罐的配套设备.蒸汽转移阀门
| (Tanks for transport of dangerous goods - Service equipment for tanks - Vapour transfer valve.)
|
NF M88-127-2003
| 危险物品运输用槽罐车.槽罐车用辅助设备.无压平衡底阀
| (Tanks for transport of dangerous goods - Service equipment for tanks - Non pressure balanced footvalve.)
|
NF M88-131-2003
| 危险物品运输用槽罐车.槽罐车用辅助设备.压力平衡底阀
| (Tanks for transport of dangerous goods - Service equipment for tanks - Pressure balanced footvalve.)
|
NF M88-729-2003
| 自闭合式LPG气瓶阀规范和试验
| (Specification and testing of LPG cylinder valves - Self closing.)
|
NF M88-729/A1-2003
| 自闭合式LPG气瓶阀规范和试验
| (Specification and testing of LPG cylinder valves - Self closing.)
|
NF M88-730-2003
| 手控LPG气瓶阀规范和试验
| (Specification and testing of LPG cylinder valves - Manually operated.)
|
NF M88-730/A1-2003
| 手控LPG气瓶阀规范和试验
| (Specification and testing of LPG cylinder valves - Manually operated.)
|
NF M88-731-2003
| 液化石油气(LPG)罐阀和配件的规范和试验
| (Specification and testing for Liquefied Petroleum Gas (LPG) tank valves and fittings.)
|
NF M88-737-2003
| 可运输可再填充液化石油气瓶用减压阀
| (Pressure relief valves for transportable refillable cylinders for Liquefied Petroleum Gas (LPG).)
|
NF M88-771-1975
| 液化烃容器装置.手动截止阀.制造.功能.试验
| (LIQUEFIED HYDROCARBON INSTALLATIONS IN CONTAINERS. MANUALLY CONTROLLED STOP VALVE. CONSTRUCTION. OPERATION. TESTS.)
|
NF M88-773-1981
| 商用丁烷容器装置.低压固定调节的家用商品丁烷减压阀
| (INSTALLATIONS BURNING COMMERCIAL BUTANE. PRESSURE REGULATOR TRIP,LOW-PRESSURE FIXED FLOW,FOR COMMERCIAL BUTANE FOR DOMESTIC USE.)
|
NF M88-775-1990
| 装液态碳氢化合物的钢瓶.可移动部分和半移动部分用高压可调减压阀.功能.标记、试验
| (LIQUEFIED HYDROCARBONS SYSTEMS IN CYLINDERS. FIXED ADJUSTEMENT,HIGH PRESSURE REGULATOR FOR MOBILE AND SEMI-MOBILE PREMISES. CONSTRUCTION. OPERATION, MARKING,TESTS.)
|
NF P16-220-2003
| 排水系统用通气阀.要求、试验方法和合格评定
| (Air admittance valves for drainage systems - Requirements, tests methods and evaluation of conformity.)
|
NF P16-260-4-2001
| 建筑物和现场用废水提升装置.施工和试验原则.第4部分:无粪便废水和含粪便物废水用单向阀
| (Wastewater lifting plants for buildings and sites - Principles of construction and testing - Part 4 : non-return valves for faecal-free wastewater and wastewater containing faecal matter.)
|
NF P40-500-2001
| 家庭计划的阀门和配件的维修服务活动.有利于水消耗控制
| (Maintenance service activities for valves and fittings in housing schemes - Contribution to water consumption control.)
|
NF P43-000-2003
| 建筑物阀门.建筑物中饮用水供应用铜合金节流阀.试验要求.国家标准补充
| (Building valves - Copper alloy stopvalves for potable water supply in buildings - Tests and requirements - National complement.)
|
NF P43-001-2000
| 建筑物用阀门.建筑物中供应引用水用铜合金截止阀.试验和要求
| (Building valves - Copper alloy stopvalves for potable water supply in buildings - Tests and requirements.)
|
NF P43-002-1981
| 建筑物水管阀门.水表截止阀.一般技术规范
| (VALVES AND TAPS FOR WATER SUPPLY IN BUILDINGS. STOP VALVES FOR METER. GENERAL TECHNICAL SPECIFICATIONS.)
|
NF P43-003-1983
| 建筑物水管阀门.冲刷水箱阀门.一般技术规范
| (VALVES FOR BUILDING. BALL FLOAT VALVES FOR FLUSHING TANKS. GENERAL TECHNICAL SPECIFICATIONS.)
|
NF P43-007-1985
| 建筑物水管阀门.A级控制非止回阀.一般技术规范
| (Valves and taps for water supply in buildings. Controllable check valves class A. General technical specifications.)
|
NF P43-009-1988
| 建筑用供水阀门.自控带中间溢流室的管路.技术规范
| (VALVES AND TAPS FOR BUILDINGS. NON CONTROLLABLE PIPE INTERRUPTOR WITH INTERMEDIATE DISCHARGE CHAMBER. GENERAL TECHNICAL SPECIFICATIONS.)
|
NF P43-011-1985
| 建筑物水管阀门.非控制不同压力范围CB断路器.一般技术规范
| (VALVES AND TAPS FOR WATER SUPPLY IN BUILDINGS. CB DISCONNECTORS WITH DIFFERENT NON CONTROLLABLE PRESSURE RANGES. GENERAL TECHNICAL SPECIFICATIONS.)
|
NF P43-013-1988
| 建筑用水管阀门.斜通气阀.通用技术规范
| (VALVES AND TAPS FOR BUILDINGS. INCLINE ANTI VACUUM VALVES (STRAIGHT OR ANGLED) DA. GENERAL TECHNICAL SPECIFICATIONS.)
|
NF P43-014-1988
| 建筑物阀门.直流永久空气接触开关.一般技术规范
| (VALVES AND TAPS FOR BUILDING. PIPE INTERRUPTOR WITH PERMANENT ATMOSPHERIC CONTACT DC. GENERAL TECHNICAL SPECIFICATIONS.)
|
NF P43-016-1985
| 建筑物水管阀门.“HA“端部断路器.一般技术规范
| (VALVES AND TAPS FOR WATER SUPPLY IN BUILDINGS. HA ENDING DISCONNECTOR FOR TAPPING COCKS. GENERAL TECHNICAL SPECIFICATIONS.)
|
NF P43-017-1989
| 建筑物水管阀门.带法兰可调EA止回阀.一般技术规范
| (VALVES AND TAPS FOR WATER SUPPLY IN BULDINGS. CONTROLLABLE CHECK VALVES EA,WITH FLANGES. GENERAL TECHNICAL SPECIFICATIONS.)
|
NF P43-018-1990
| 建筑物水管阀门.饮用水卫生监测仪器.特性
| (VALVES AND TAPS FOR WATER SUPPLY IN BUILDINGS. CHECKING FITTING IN PLACE OF SANITARY PROTECTION UNITIES USED FOR DRINKING SUPPLY. SPECIFICATIONS.)
|
NF P43-022-1988
| 建筑物水管阀门.AC分流溢出的设备.通用技术规范
| (VALVES AND TAPS FOR BUILDINGS. AIR GAP WITH DIVERTER AND OVERFLOW AC. GENERAL SPECIFICATIONS.)
|
NF P43-023-1988
| 建筑物水管阀门.AD喷射溢出的设备.一般规范
| (VALVES AND TAPS FOR BUILDINGS. AIR GAP WITH INJECTOR AD. GENERAL SPECIFICATIONS.)
|
NF P43-024-1988
| 建筑物水管阀门.AE卫生设施及设备.一般规范
| (VALVES AND TAPS FOR BUILDINGS. HYGIENIC AIR GAP AE. GENERAL SPECIFICATIONS.)
|
NF P43-035-2000
| 建筑阀门.供水减压阀和复合供水减压阀.要求和试验
| (Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests.)
|
NF P50-746-2000
| 建筑物结构中的热桥.线性热阀门.简化方法和无效阀门
| (Thermal bridges in building construction - Linear thermal transmittance - Simplified methods and default values.)
|
NF P50-757-2000
| 建筑材料和产品.湿热性能.列表设计的阀门
| (Building materials and products - Hygrothermal properties - Tabulated design values.)
|
NF P52-001-1975
| 取暖设备用安全阀.一般技术规范
| (SAFETY VALVES FOR HEATING INSTALLATIONS.)
|
NF P52-002-1-1989
| 散热器恒温阀.第1部分:试验方法的要求
| (Thermostatic radiator valves. Part 1 : requirements and test methods.)
|
NF R16-316-1989
| 道路车辆.带凸缘和节流阀式试验喷咀
| (Road vehicles. Calibrating nozzle, delay pintle type.)
|
NF S31-014-1982
| 声学.供水设施用液压设备和阀门噪音的实验室测量.第1部分:测量方法
| (ACOUSTICS. LABORATORY TESTS ON NOISE FORM TAPWARE AND HYDRAULIC EQUIPMENT USED IN WATER INSTALLATIONS. PART 1 : METHOD OF MEASUREMENT.)
|
NF S31-014-3-1997
| 声学.用于供水安装的设备和应用的噪音发散的实验室试验.第3部分:内线阀门和应用的安装和操作条件
| (Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Part 3 : mounting and operating conditions for in-line valves and appliances.)
|
NF S31-014-4-1997
| 声学.用于供水安装的设备和用具中发散的噪音的实验室试验.第3部分:串联式的阀门和用具的镶嵌和操作条件
| (Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Part 4 : mounting and operating conditions for special appliances.)
|
NF S52-728-1994
| 越野滑雪.扭距阀选择
| (ALPINE SKI-BINDINGS. SELECTION OF RELEASE TORQUE VALUES.)
|
NF S62-135-2001
| 固定式消防系统.气体灭火系统用元件.第5部分:CO2系统用的高、低压选择器阀门及其起动器的要求和试验方法
| (Fixed firefighting systems - Components for gas extinguishing systems - Part 5 : requirements and test methods for high and low pressure selector valves and their actuators for CO2 systems.)
|
NF S62-143-2001
| 固定的消防系统.气体灭火系统用元件.第13部分:止回阀的要求和试验方法
| (Fixed firefighting systems - Components for gas extinguishing systems - Part 13 : requirements and test methods for check valves and non-return valves.)
|
NF S62-222-1999
| 固定的消防系统.喷头和喷水系统用元部件.第2部分:报警湿阀组件
| (Fixed firefighting systems - Components for sprinkler and water spray systems - Part 2 : wet alarm valve assemblies.)
|
NF S62-222/A1-2001
| 固定灭火系统.喷头和喷水系统用元部件.第2部分:报警湿阀组件
| (Fixed firefighting systems - Components for sprinkler and water spray systems - Part 2 : wet alarm valve assemblies.)
|
NF S62-223-2000
| 固定灭火系统.自动洒水器和喷水系统用元件.第1部分:警报干阀组件
| (Fixed firefighting systems - Components for automatic sprinkler and water spray systems - Part 3 : dry alarm valves assemblies.)
|
NF S62-223/A1-2001
| 固定灭火系统.喷头和喷水系统用元部件.第3部分:报警干阀组件
| (Fixed firefighting systems - Components for sprinkler and water spray systems - Part 3 : dry alarm valve assemblies.)
|
NF S76-017-1999
| 呼吸保护装置.无吸入阀和有防止气体或气体微粒或只有微粒的分隔滤膜的半口罩.(欧洲标准EN 1827)
| (RESPIRATORY PROTECTIVE DEVICES. HALF MASKS WITHOUT INHALATION VALVES AND WITH SEPARABLE FILTERS TO PROTECT AGAINST GASES OR GASES AND PARTICLES OR PARTICLES ONLY. REQUIREMENTS, TESTING, MARKING. (EUROPEAN STANDARD EN 1827).)
|
NF S76-024-1-2000
| 呼吸保护装置.气瓶阀.插入式连接器用螺纹接头
| (Respiratory protective devices - Gas cylinder valves - Part 1 : thread connections for insert connector.)
|
NF S76-024-1/A1-2003
| 呼吸防护装置.气瓶阀门.第1部分:旋入式连接器的螺纹连接件
| (Respiratory protective devices - Gas cylinder valves - Part 1 : thread connections for insert connector.)
|
NF S76-024-2-1999
| 呼吸保护装置.气瓶阀.插座接头
| (RESPIRATORY PROTECTIVE DEVICES. GAS CYLINDER VALVES. PART 2 : OUTLET CONNECTIONS. (EUROPEAN STANDARD EN 144-2).)
|
NF S76-024-3-2003
| 呼吸保护器.气瓶阀.第3部分:潜水硝基气体和氧气气瓶的出口连接
| (Respiratory protective devices - Gas cylinder valves - Part 3 : outlet connections for diving gases Nitrox and oxygen.)
|
NF S90-110-1996
| 便携式气瓶.医用指针指示马蹄型阀门排出口接头
| (Transportable gas cylinders. Pin-index, yoke-type valve outlet connections for medical use.)
|
NF S90-110/A1-2001
| 可移动的燃气瓶.医用定位销转位的卡箍式阀出口连接
| (Transportable gas cylinders - Pin-index, yoke-type valve outlet connections for medical use.)
|
NF S94-201-2-1998
| 非活动外科植入物.血管和心脏植入物的特殊要求.包括心脏阀门管线的血管修补物
| (NON ACTIVE SURGICAL IMPLANTS. PARTICULAR REQUIREMENTS FOR CARDIAC AND VASCULAR IMPLANTS. PART 2 : VASCULAR PROSTHESES INCLUDING CARDIAC VALVE CONDUITS. (EUROPEAN STANDARD EN 12006-2).)
|
NF S95-178-1998
| 医用气体用压力调节器.第3部分:与钢瓶阀门相结合的压力调节器(欧洲标准EN 738-3)
| (PRESSURE REGULATORS FOR USE WITH MEDICAL GASES. PART 3 : PRESSURE REGULATORS INTEGRATED WITH CYLINDER VALVES. (EUROPEAN STANDARD EN 738-3).)
|
NF S95-178/A1-2002
| 医用气体压力调节器.第3部分:带瓶阀的压力调节器
| (Pressure regulators for use with medical gases - Part 3 : pressure regulators integrated with cylinder valves.)
|
NF T54-015-1997
| 塑料管道系统.热塑阀门.抗内压和防泄漏的试验方法
| (Plastics piping systems. Thermoplastics valves. Test methods for resistance to internal pressure and leaktightness.)
|
NF T54-063-4-2003
| 供水用塑料管道系统.聚乙烯(PE).第4部分:阀
| (Plastics piping systems for water supply - Polyethylene (PE) - Part 4 : valves.)
|
NF T54-065-4-2003
| 气体燃料的塑料管道供应系统.聚乙烯(PE).第4部分:阀门
| (Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4 : valves.)
|
NF T54-082-1988
| 塑料.热固塑料阀.耐压和密封性试验
| (PLASTICS. THERMOPLASTIC AND THERMOSETTING VALVES. TEST OF RESISTANCE TO PRESSURE.)
|
NF T54-083-1991
| 热塑料制阀门.转矩.试验方法.(欧洲标准EN 28233)
| (THERMOPLASTICS VALVES. TORQUE. TEST METHOD. (EUROPEAN STANDARD EN 28233).)
|
NF T54-084-1991
| 热塑料制阀门.耐疲劳强度.试验方法.(欧洲标准EN 28659)
| (THERMOPLASTICS VALVES. FATIGUE STRENGTH. TEST METHOD. (EUROPEAN STANDARD EN 28659).)
|
NF T54-100-1997
| 塑料管道系统.热塑阀门.外部送风后阀门完好性的测试方法
| (Plastics piping systems. Thermoplastics valves. Test method for the integrity of a valve after an external blow.)
|
NF T54-300-4-2003
| 普通用水、排水、污水地下和地上压力系统用塑料管道系统.聚乙烯(PE).第4部分:阀门
| (Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 4 : valves.)
|
NF T54-920-1997
| 塑料管道系统.聚乙烯管道系统用阀门.在工作机构弯头处和弯头之后的防漏试验方法(欧洲标准EN 1680)
| (Plastics piping systems. Valves for polyethylene (PE) piping systems. Test method for leaktightness under and after bending applied to the operating mechanism.)
|
NF T54-921-1997
| 塑料管道系统.热塑阀门.弯曲下温度周期变化后阀门完好性的测试方法
| (Plastics piping systems. Thermoplastics valves. Test method for the integrity of a valve after temperature cycling under bending.)
|
NF T54-930-1997
| 塑料管道系统.聚乙烯(PE)阀.支架间耐弯曲试验方法
| (Plastics piping systems. Polyethylene (PE) valves. Test method for resistance to bending between supports.)
|
NF T54-932-1997
| 塑料管道系统.注模热塑配件配件、阀和附属设备.管道元件注模用热塑材料长期液压强度的测定
| (Plastics piping systems. Injection-moulded thermoplastics fittings, valves and ancillary equipment. Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components.)
|
NF T54-934-1997
| 塑料管道系统.管件,阀和附件.气流率/压降关系的测定
| (Plastics piping systems. Fittings, valves and ancillaries. Determination of gaseous flow rate/pressure drop relationships.)
|
NF T54-936-1997
| 塑料管道系统.聚乙烯(PE)阀.耐热循环试验方法(欧洲标准EN 12119)
| (Plastics piping systems. Polyethylene (PE) valves. Test method for resistance to thermal cycling.)
|
NF T81-103-1980
| 液态体化学产品的运输和装卸.底部注入或排放的罐车.内部关闭阀和安全阀.使用压力等于或小于4巴
| (TRANSPORTATION AND HANDLING OF LIQUID CHEMICAL PRODUCTS. TANKER VEHICLES FILLED AND EMPTIED FROM BELOW. INTERNAL SAFETY AND STOP VALVE. OPERATING PRESSURE EQUAL TO OR LESS THAN 4 BAR.)
|
NF T81-104-1981
| 液态体化学产品的运输和装卸.底部注入或排放的罐车.4-40bar工作压力用标准尺寸DN80和DN100的
| (TRANSPORTATION AND HANDLING OF LIQUEFIED GASES. TANKER VEHICULES FILLED AND EMPTIED FROM BELOW. INTERNAL SAFETY GATES DN 80 AND DN 100 FOR OPERATING PRESSURES BETWEEN 4 BAR AND 40 BAR.)
|
NF T81-151-1977
| 化学产品的运输与装卸.道路罐车.用销或螺栓固定的阀门用圆盖
| (TRANSPORTATION AND HANDLING OF CHEMICALS. ROAD TANKERS. CAPS FOR VALVES FIXED BY PINS OR BOLTS.)
|
NF U51-421-1985
| 灌溉设备.容积阀.一般技术条件和试验方法
| (IRRIGATION EQUIPMENT. VOLUMETRIC VALVES. GENERAL REQUIREMENTS AND TEST METHOD.)
|
NF X08-102-1986
| 颜色.实验室用阀门.液体鉴别通用颜色
| (Colours. Laboratory topware. Identification of fluids with conventional colours.)
|
NF X42-129-2001
| 生物技术.管道和仪表的性能标准.第5部分:阀门
| (Biotechnology - Performance criteria for piping and instrumentation - Part 5 : valves.)
|
NF X43-103-1996
| 空气质量.气味测量.污水气味测量.超阀限方法
| (AIR QUALITY. OLFACTOMETRIC MEASUREMENTS. MEASUREMENT OF THE ODOUR OF A GAZEOUS EFFLUENT. SUPRA-THRESHOLD METHODS.)
|
NF X50-001-7-1-2000
| 动力站设备和系统的征购指南.第7部分:管道和阀门.第1节:高压管道系统
| (Guide for procurement of power station plant, equipement and systems - Part 7 : pipework and valves - Section 1 : high pressure piping systems.)
|
NF X50-001-7-2-2000
| 动力站设备和系统的征购指南.第7部分:管道和阀门.第2节:锅炉和高压管道阀门
| (Guide for procurement of power station plant, equipment and systems - Part 7 : pipework and valves - Section 2 : boiler and high pressure piping valves.)
|
XP E29-140-1999
| 使用气体燃料的家用装置的控制阀.安全控制阀(带有集中自动密闭器的)
| (Control cocks for household appliances using gaseous fuels - Safety cocks (with integrated automatic obturator).)
|
编号 | 中文名称 | 英文名称 |