| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| NF A00-501-3-1991 | 铸件.订货和供应的一般技术条件.第3部分:通过重量压力和负压的铝合金及镁合金的铸件 | (FOUNDRY PRODUCTS. GENERAL TECHNICAL CONDITIONS FOR ORDERING AND SUPPLYING. PART 3 : GRAVITY,LOW PRESSURE AND VACUUM CASTINGS OF ALUMINIUM ALLOYS AND MAGNESIUM ALLOYS.) |
| NF A01-010-1971 | 铝和铝合金,铜和铜合金.取样、样品和试验用的试件 | (ALUMINIUM AND ALUMINIUM ALLOYS. COPPER AND COPPER ALLOYS. SAMPLES, SPECIMENS AND TEST PIECES.) |
| NF A02-011-1970 | 铝及铝合金.热处理和机械处理的词汇 | (ALUMINIUM AND ALUMINIUM ALLOYS. VOCABULARY OF HEAT TREATMENTS AND MECHANICAL TREATMENTS.) |
| NF A02-120-1994 | 铝和铝合金.锻制产品的化学成分和产品形状.第1部分:数字命名系统 | (Aluminium and aluminium alloys. Chemical composition and form of wrought products. Part 1 : numerical designation system.) |
| NF A02-120-3-2003 | 铝和铝合金.化学成分和锻造产品的外形.第3部分:化学成分 | (Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3 : chemical composition.) |
| NF A02-121-1994 | 铝和铝合金.锻制产品的化学成分和外形.第2部分:基于名称与符号系统的化学符号 | (Aluminium and aluminium alloys. Chemical composition and form of wrought products. Part 2 : chemical symbol based designation system.) |
| NF A02-122-1994 | 铝和铝合金.锻制产品的化学成分和产品形状.第3部分:化学成分 | (ALUMINIUM AND ALUMINIUM ALLOYS. CHEMICAL COMPOSITION AND FORM OF WROUGHT PRODUCTS. PART 3 : CHEMICAL COMPOSITION. (EUROPEAN STANDARD EN 573-3).) |
| NF A02-123-1994 | 铝和铝合金.锻制产品的化学成分和产品形状.第4部分:产品的形式 | (ALUMINIUM AND ALUMIMIUM ALLOYS. CHEMICAL COMPOSITION AND FORM OF WROUGHT PRODUCTS. PART 4 : FORM OF PRODUCTS. (EUROPEAN STANDARD EN 573-4).) |
| NF A02-130-1-2003 | 铝及铝合金.再熔主合金和铸件用合金铝锭的名称与符号.第1部分:数字命名系统 | (Aluminium and aluminium alloys - Designation of alloyed aluminium ingots for remelting, master alloys and castings - Part 1 : numerical designation system.) |
| NF A02-130-2-2003 | 铝及铝合金.再熔主合金和铸件用合金铝锭的名称与符号.第2部分:基于命名系统的化学符号 | (Aluminium and aluminium alloys - Designation of alloyed aluminium ingots for remelting, master alloys and castings - Part 2 : chemical symbol based designation system.) |
| NF A02-130-3-2003 | 铝及铝合金.再熔主合金和铸件用合金铝锭的名称与符号.第3部分:化合物的书写规则 | (Aluminium and aluminium alloys - Designation of alloyed aluminium ingots for remelting, master alloys and castings - Part 3 : writing rules for chemical composition.) |
| NF A02-150-1993 | 锻铝和铝合金锻制产品名称术语 | (Aluminium and aluminium alloys. Wrought products. Temper designations.) |
| NF A03-253-1972 | 铝和铝合金.铜和铜合金.维氏硬度试验.0.2-120公斤力的试验负荷 | (Aluminium and aluminium alloys. Copper and copper alloys. Vicker hardness. Test-loads ranging from 0,2 to 120 kgf.) |
| NF A03-260-1972 | 铝和铝合金.铜和铜合金.简单弯曲折叠试验 | (ALUMINIUM AND ALUMINIUM ALLOYS. COPPER AND COPPER ALLOYS. ORDINARY BENDING TEST.) |
| NF A03-268-1971 | 铝和铝合金.铜和铜合金.线材的简单扭转试验 | (ALUMINIUM AND ALUMINIUM ALLOYS. COPPER AND COPPER ALLOYS. SIMPLE TORSION TEST FOR WIRE.) |
| NF A03-301-2002 | 铸件.图像分析法测量均差.含5%-11%硅的铝铸件 | (Founding - Measurement of the mean intercept using image analysis - Aluminium castings with a 5 to 11 content % of silicium.) |
| NF A04-150-1984 | 用射线照相术检查铝合金和镁合金铸件 | (Radiographic examination of aluminium and magnesium alloy castings.) |
| NF A04-503-1988 | 铝、铜、镍及其合金制半成品.粒径的测定.铝和铝合金 | (Semi-products made from aluminium, copper, nickel and their alloys. Determination of grain size. Aluminium and aluminium alloys.) |
| NF A04-505-1988 | 铝、铜、镍及其合金制半成品.粒径的测定.镍和镍合金 | (Semi-products made from aluminium, copper, nickel and their alloys. Determination of grain size. Nickel and nickel alloys.) |
| NF A05-301-1981 | 铝合金.厚铝应力腐蚀试验 | (Aluminium alloys. Stress corrosion cracking of thick products.) |
| NF A05-306-1984 | 铝合金.薄铝制品腐蚀试验 | (ALUMINIUM ALLOYS (SERIE 5XXX). EXFOLIATION CORROSION TESTING.) |
| NF A06-551-1976 | 铝和铝合金的化学分析.铜的分光光度测定 | (Chemical analysis of aluminium and aluminium alloys. Spectrophotometric determination of copper.) |
| NF A06-552-1964 | 铝和铝合金的化学分析.铜的测定 | (Chemical analysis of aluminium and aluminium alloys. Determination of copper.) |
| NF A06-553-1966 | 铝和铝合金的化学分析.锌的测定 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ALUMINIUM ALLOYS. DETERMINATION OF ZINC.) |
| NF A06-564-1969 | 抗摩擦铝合金的化学分析.锡的容量法测定 | (CHEMICAL ANALYSIS OF ALUMINIUM ANTIFRICTION ALLOYS. VOLUMETRIC DETERMINATION OF TIN.) |
| NF A06-568-1971 | 铝和铝合金的化学分析.锡的分光光度测定 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ALUMINIUM ALLOYS. SPECTROPHOTOMETRIC DETERMINATION OF TIN.) |
| NF A06-570-1964 | 铝和铝合金的化学分析.硅总含量的测定 | (Chemical analysis of aluminium and aluminium alloys. Determination of total silicon.) |
| NF A06-571-1964 | 铝和铝合金的化学分析.铁的分光光度测定 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ALUMINIUM ALLOYS. SPECTROPHOTOMETRIC DETERMINATION OF IRON.) |
| NF A06-574-1966 | 铝和铝合金的化学分析.钛的分光光度测定 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ALUMINIUM ALLOYS. SPECTROPHOTOMETRIC DETERMINATION OF TITANIUM.) |
| NF A06-575-1971 | 铝合金的化学分析.镍的重量法测定 | (CHEMICAL ANALYSIS OF ALUMINIUM ALLOYS. GRAVIMETRIC DETERMINATION OF NICKEL.) |
| NF A06-576-1966 | 铝和铝合金的化学分析.锰的分光光度测定 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ALUMINIUM ALLOYS. SPECTROPHOTOMETRIC DETERMINATION OF MANGANESE.) |
| NF A06-577-1984 | 铝和铝合金的化学分析.钴的比色法测定 | (Chemical analysis of aluminium and aluminium alloys. Colorimetric determination of cobalt.) |
| NF A06-579-1966 | 铝和铝合金的化学分析.镁的测定 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ALUMINIUM ALLOYS. DETERMINATION OF MAGNESIUM.) |
| NF A06-581-1984 | 铝和铝合金的化学分析.铬的比色法测定 | (Chemical analysis of aluminium and aluminium alloys. Colorimetric determination of chromium.) |
| NF A06-582-1959 | 铝和铝合金的化学分析.锆的分光光度测定 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ALUMINIUM ALLOYS. COLORIMETRIC DETERMINATION OF ZIRCONIUM.) |
| NF A06-583-1984 | 铝和铝合金的化学分析.铋的分光光度测定 | (Chemical analysis of aluminium and aluminium alloys. Spectrophotometric determination of bismuth.) |
| NF A06-584-1984 | 铝和铝合金的化学分析.铍的分光光度测定 | (Chemical analysis of aluminium and aluminium alloys. Spectrophotometric determination of berrylium.) |
| NF A06-585-1965 | 铝和铝合金的化学分析.铅的测定 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ALUMINIUM ALLOYS. DETERMINATION OF LEAD.) |
| NF A06-586-1965 | 铝和铝合金的化学分析.硼的分光光度测定 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ALUMINIUM ALLOYS. SPECTROPHOTOMETRIC DETERMINATION OF BORON.) |
| NF A06-587-1965 | 铝和铝合金的化学分析.汞的测定 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ALUMINIUM ALLOYS. DETERMINATION OF MERCURY.) |
| NF A06-588-1970 | 铝的化学分析.钒的分光光度测定 | (CHEMICAL ANALYSIS OF ALUMINIUM. SPECTROPHOTOMETRIC DETERMINATION OF VANADIUM.) |
| NF A06-602-1984 | 镁和镁合金的化学分析.铝的测定 | (Chemical analysis of magnesium and magnesium alloys. Determination of aluminium.) |
| NF A06-714-1968 | 铜和铜合金的化学分析.铝的分光光度测定 | (CHEMICAL ANALYSIS OF COPPER AND ITS ALLOYS. SPECTROPHOTOMETRIC DETERMINATION OF ALUMINIUM.) |
| NF A06-754-1968 | 铜合金的化学分析.铝的重量分析法测定 | (CHEMICAL ANALYSIS OF COPPER ALLOYS. GRAVIMETRIC DETERMINATION OF ALUMINIUM.) |
| NF A06-835-1973 | 电镀用锌的分析.铝分光光度测定 | (ZINC FOR GALVANIZING PURPOSES. SPECTROPHOTOMETRIC DETERMINATION OF ALUMINIUM.) |
| NF A06-841-1-2002 | 锌及锌合金.化学分析.第1部分:锌合金中铝的测定.滴定法 | (Zinc and zinc alloys - Chemical analysis - Part 1: determination of aluminium in zinc alloys - Titrimetric method.) |
| NF A06-841-6-2003 | 锌及锌合金.化学分析.第6部分:用火焰原子吸收光谱法测定铝和铁的含量 | (Zinc and zinc alloys - Chemical analysis - Part 6 : determination of aluminium and iron by atomic absorption spectrometry.) |
| NF A07-500-1979 | 铝及其合金的发射光谱分析 | (ANALYSIS OF ALUMINIUM AND ITS ALLOYS BY EMISSION SPECTROMETRY.) |
| NF A07-510-1971 | 非合金铝的发射光谱分析 | (Analysis of non-alloyed aluminium by emission spectrography.) |
| NF A07-510X2-1975 | 非合金铝的发射光谱分析 | (ANALYSIS OF NON-ALLOYED ALUMINIUM BY EMISSION SPECTROGRAPHY.) |
| NF A07-515-1971 | 铝铜合金的发射光谱分析 | (ANALYSIS OF ALUMINIUM COPPER ALLOYS BY EMISSION SPECTROGRAPHY.) |
| NF A07-520-1971 | 铝硅及铝硅铜合金的发射光谱分析 | (ANALYSIS OF ALUMINIUM SILICON AND ALUMINIUM-SILICON-COPPER ALLOYS BY EMISSION SPECTROGRAPHY.) |
| NF A08-001-1979 | 轻金属及合金的化学分析.原子吸收光谱法在铝、镁及其合金分析中的应用 | (CHEMICAL ANALYSIS OF LIGHT METALS AND ALLOYS. APPLICATION OF ATOMIC ABSORPTION SPECTROMETRY TO THE ANALYSIS OF ALUMINIUM,MAGNESIUM AND THEIR ALLOYS.) |
| NF A08-547-1979 | 铝及其合金的化学分析.铅的测定.原子吸收法 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ITS ALLOYS. DETERMINATION OF LEAD. ATOMIC ABSORPTION METHOD.) |
| NF A08-553-1979 | 铝及其合金的化学分析.锌的测定.原子吸收法 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ITS ALLOYS. DETERMINATION OF ZINC. ATOMIC ABSORPTION METHOD.) |
| NF A08-556-1979 | 铝及其合金的化学分析.铬的测定.原子吸收法 | (CHEMICAL ANALYSIS OF ALUMINIUM AND ITS ALLOYS. DETERMINATION OF CHROMIUM. ATOMIC ABSORPTION METHOD.) |
| NF A08-563-1974 | 铝合金的化学分析.锑的测定(原子吸收法) | (CHEMICAL ANALYSIS OF ALUMINIUM ALLOYS. DETERMINATION OF ANTIMONY. (ATOMIC ABSORPTION METHOD).) |
| NF A08-568-1974 | 铝合金的化学分析.锡的测定(原子吸收法) | (CHEMICAL ANALYSIS OF ALUMINIUM ALLOYS. DETERMINATION OF TIN. (ATOMIC ABSORPTION METHOD).) |
| NF A08-650-1992 | 钛及钛合金的化学分析.用火焰原子吸收光谱法测定TA6V合金内铝、钒和铁的含量 | (CHEMICAL ANALYSIS OF TITANIUM AND TITANIUM ALLOYS. DETEMINATION OF ALUMINIUM, VANADIUM AND IRON CONTENTS IN THE TA6V ALLOY BY FLAME ATOMIC ABSORPTION SPECTROPHOTOMETRY.) |
| NF A08-651-1993 | 钛及铝合金的化学分析.用火焰原子吸收光谱及等离子排放光谱法测定TA6V合金内低合金的元素含量的测定 | (CHEMICAL ANALYSIS OF TITANIUM AND ALUMINIUM ALLOYS. DETERMINATION OF ELEMENTS CONTENTS IN LOW CONTENT IN THE TA6V ALLOY. METHOD BY FLAME ATOMATIC ABSORPTION SPECTROMETRY OR BY PLASMA EMISSION SPECTROMETRY.) |
| NF A08-714-1983 | 铜和铜合金.铝的测定.火焰原子吸收光谱测定法 | (Copper and copper alloys. Determination of aluminium content. Flame atomic absorption spectrometric method.) |
| NF A08-811-1970 | 锌的化学分析.铅、镉、铜和铝的测定(原子吸收法) | (CHEMICAL ANALYSIS OF ZINC. DETERMINATION OF LEAD,CADMIUM,COPPER AND ALUMINIUM. (ATOMIC ABSORPTION METHOD).) |
| NF A08-825-1973 | 锌合金的化学分析.铝的测定(原子吸收法) | (CHEMICAL ANALYSIS OF ZINC ALLOYS. DETERMINATION OF ALUMINIUM. (ATOMIC ABSOPTION METHOD).) |
| NF A10-186-1977 | 铁合金的化学分析.硅铁合金中铝含量的测定.原子吸收光谱法 | (CHEMICAL ANALYSIS OF FERROALLOYS. DETERMINATION OF ALUMINIUM IN FERROSILICON. ATOMIC ABSORPTION SPECTROMETRIC METHOD.) |
| NF A11-015-1974 | 钛铁的化学分析.铝的络合测定.滴定法 | (CHEMICAL ANALYSIS OF FERRO-TITANIUM. COMPLEXOMETRIC DETERMINATION OF ALUMINIUM CONTENT.) |
| NF A20-417-1984 | 铁矿石.铝含量的测定.滴定分析法和喔星重量法 | (IRON ORES. DETERMINATION OF ALUMINIUM CONTENT. OXINE GRAVIMETRIC AND TITRIMETRIC METHODS.) |
| NF A20-605-1984 | 铁矿石.铝的测定.火焰原子吸收分光光度法 | (Iron ores. Determination of aluminium content. Flame atomic absorption spectrometric method.) |
| NF A22-400-1977 | 锰矿石的化学分析.用原子吸收光谱分析法测定氧化铝、石灰和氧化镁 | (CHEMICAL ANALYSIS OF MANGANESE ORES. DETERMINATION OF ALUMINA,LIME AND MAGNESIA ATOMIC ABSORPTION SPECTROMETRIE METHOD.) |
| NF A35-035-2001 | 钢产品.热镀锌或锌铝覆层的预应力光滑钢丝和7股钢丝 | (Steel products - Hot-dip zinc or zinc-aluminium coated prestressing smooth wires and 7-wire strands.) |
| NF A36-325-1995 | 连续热浸镀铝锌薄钢板和钢带.交货技术条件 | (CONTINUOUSLY HOT-DIP ALUMINIUM-ZINC (AZ) COATED STEEL STRIP AND SHEET. TECHNICAL DELIVERY CONDITIONS. (EUROPEAN STANDARD EN 10215).) |
| NF A36-340-2002 | 连续热浸铝-硅涂覆的钢条和钢板.交货技术条件 | (Continuously hot-dip aluminium-silicon (AS) coated steel strip and sheet - Technical delivery conditions.) |
| NF A36-345-1991 | 冶金产品.铝合金薄板,薄板和卷材 | (IRON AND STEEL. ALUMINIUM COATED SHEET. CUT LENGTHS AND COILS.) |
| NF A37-602-3-2001 | 钢丝和丝产品.钢丝上的非有色金属涂层.第3部分:铝涂层 | (Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 3 : aluminium coatings.) |
| NF A50-001-1-1998 | 铝和铝合金.条款和定义.第1部分:一般条款 | (Aluminium and aluminium alloys. Terms and definitions. Part 1 : general terms.) |
| NF A50-001-3-2003 | 铝及铝合金.术语和定义.第3部分:废料 | (Aluminium and aluminium alloys - Terms and definitions - Part 3 : scrap.) |
| NF A50-100-1994 | 锻铝和铝合金.用于生产与食品接触的材料和物品的金属的化学成分 | (Aluminium and aluminium alloys. Wrought products. Chemical composition of semi-products used for the fabrication or articles for use in contact with food.) |
| NF A50-110-1-2003 | 铝和铝合金.废料.第1部分:一般要求、取样和试验 | (Aluminium and aluminium alloys - Scrap - Part 1 : general requirements, sampling and tests.) |
| NF A50-110-10-2003 | 铝和铝合金.废料.第10部分:使用过的铝制饮料罐组成的废料 | (Aluminium and aluminium alloys - Scrap - Part 10 : scrap consisting of used aluminium beverage cans.) |
| NF A50-110-11-2003 | 铝和铝合金.废料.第11部分:铝铜散热器废料 | (Aluminium and aluminium alloys - Scrap - Part 11 : scrap consisting of aluminium-copper radiators.) |
| NF A50-110-12-2003 | 铝和铝合金.废料.第12部分:一种合金组成的车床切屑 | (Aluminium and aluminium alloys - Scrap - Part 12 : turnings consisting of one single alloy.) |
| NF A50-110-13-2003 | 铝和铝合金.废料.第13部分:两种或多种合金组成的混合切屑 | (Aluminium and aluminium alloys - Scrap - Part 13 : mixed turnings consisting of two or more alloys.) |
| NF A50-110-14-2003 | 铝和铝合金.废料.第14部分:旧的铝制包装件组成的废料 | (Aluminium and aluminium alloys - Scrap - Part 14 : scrap from post-consumer aluminium packagings.) |
| NF A50-110-15-2003 | 铝和铝合金.废料.第15部分:去除涂层的旧铝包装件废料 | (Aluminium and aluminium alloys - Scrap - Part 15 : decoated aluminium scrap from post-consumer aluminium packagings.) |
| NF A50-110-16-2003 | 铝和铝合金.废料.第16部分:浮渣、碎屑、小金属棒和金属粒子组成的废料 | (Aluminium and aluminium alloys - Scrap - Part 16 : scrap consisting of skimmings, drosses, spills and metallics.) |
| NF A50-110-2-2003 | 铝和铝合金.废料.第2部分:非合金铝废料 | (Aluminium and aluminium alloys - Scrap - Part 2 : unalloyed aluminium scrap.) |
| NF A50-110-3-2003 | 铝和铝合金.废料.第3部分:导线和电缆废料 | (Aluminium and aluminium alloys - Scrap - Part 3 : wire and cable scrap.) |
| NF A50-110-4-2003 | 铝和铝合金.废料.第4部分:由一种可锻合金组成的废料 | (Aluminium and aluminium alloys - Scrap - Part 4 : scrap consisting of one single wrought alloy.) |
| NF A50-110-5-2003 | 铝和铝合金.废料.第5部分:同系列两种或多种可锻合金组成的废料 | (Aluminium and aluminium alloys - Scrap - Part 5 : scrap consisting of two or more wrought alloys of the same series.) |
| NF A50-110-6-2003 | 铝和铝合金.废料.第6部分:两种或多种可锻合金组成的废料 | (Aluminium and aluminium alloys - Scrap - Part 6 : scrap consisting of two or more wrought alloys.) |
| NF A50-110-7-2003 | 铝和铝合金.废料.第7部分:铸件组成的废料 | (Aluminium and aluminium alloys - Scrap - Part 7 : scrap consisting of castings.) |
| NF A50-110-8-2003 | 铝和铝合金.废料.第8部分:铝分离工艺中切碎工艺产生的有色金属材料组成的废料 | (Aluminium and aluminium alloys - Scrap - Part 8 : scrap consisting of non-ferrous materials from shredding processes destined to aluminium separation processes.) |
| NF A50-110-9-2003 | 铝和铝合金.废料.第9部分:有色金属碎料的铝分离工艺产生的废料 | (Aluminium and aluminium alloys - Scrap - Part 9 : scrap from aluminium separation processes of non-ferrous shredded materials.) |
| NF A50-120-2000 | 铝和铝合金.锻造产品.生产压力器件的产品的特殊要求 | (Aluminium and aluminium alloys - Wrought products - Special requirements for products intended for the production of pressure equipment.) |
| NF A50-125-2003 | 铝及铝合金.电工用铝薄板材、带材和板材 | (Aluminium and aluminium alloys - Aluminium sheet, strip and plate for electrotechnical applications.) |
| NF A50-150-1-2002 | 铝和铝合金.船用锻造和铸造产品:第1部分:规范 | (Aluminium and aluminium alloys - Wrought and cast products for marine applications (shipbuilding, marine and offshore) - Part 1 : specifications.) |
| NF A50-181-1970 | 铝和铝合金.薄带和箔金属薄片.机械试验.拉力、冲压、崩裂 | (ALUMINIUM AND ALUMINIUM ALLOYS. FOILS. MECHANICAL TESTS.) |
| NF A50-261-1977 | 铝和铝合金.薄带钢和金属薄片.物理试验、铝带多孔性、可湿性、厚度.铝带附着力 | (ALUMINIUM AND ALUMINIUM ALLOYS. FOILS. PHYSICAL TESTS.) |
| NF A50-400-1994 | 铝和铝合金.半连续铸造轧制铸锭 | (ALUMINIUM AND ALUMINIUM ALLOYS. ROLLING INGOTS. SPECIFICATIONS. (EUROPEAN STANDARD EN 487).) |
| NF A50-421-1994 | 锻铝和铝合金钢材,带材和板材.第2部分:机械性能 | (Aluminium and aluminium alloys. Sheet, strip and plate. Part 2 : mechanical properties.) |
| NF A50-422-2003 | 铝和铝合金.带材、薄板和板材.第3部分:热轧制品的尺寸和外形公差 | (Aluminium and aluminium alloys - Sheet, strip and plate - Part 3 : tolerances on dimensions and form for hot-rolled products.) |
| NF A50-430-1995 | 铝和铝合金.一般用途的圆制品和圆坯的规格 | (Aluminium and aluminium alloys. Circle and circle stock for general applications. Specifications.) |
| NF A50-431-1995 | 铝和铝合金.烹调器具生产用圆坯料.规范 | (Aluminium and aluminium alloys. Circle and circle stock for the production of culinary utensils. Specifications.) |
| NF A50-432-1997 | 铝和铝合金.通用盘绕涂层的薄板和带材.规范 | (ALUMINIUM AND ALUMINIUM ALLOYS. COIL COATED SHEET AND STRIP FOR GENERAL APPLICATIONS. SPECIFICATIONS. (EUROPEAN STANDARD EN 1396).) |
| NF A50-433-1997 | 铝和铝合金.踏脚板.规范(欧洲标准EN 1386) | (ALUMINIUM AND ALUMINIUM ALLOYS. TREAD PLATE. SPECIFICATIONS. (EUROPEAN STANDARD EN 1386).) |
| NF A50-434-1-1998 | 铝及铝合金.一般用途再轧坯料.第1部分:热轧制再轧坯料规范 | (ALUMINIUM AND ALUMINIUM ALLOYS. REROLL STOCK FOR GENERAL APPLICATIONS. PART 1 : SPECIFICATIONS FOR HOT-ROLLED REROLL STOCK. (EUROPEAN STANDARD EN 12482-1).) |
| NF A50-434-2-1998 | 铝及铝合金.一般用途再轧坯料.第2部分:冷轧制再轧坯料规范 | (ALUMINIUM AND ALUMINIUM ALLOYS. REROLL STOCK FOR GENERAL APPLICATIONS. PART 2 : SPECIFICATIONS FOR COLD-ROLLED REROLL STOCK. (EUROPEAN STANDARD EN 12482-2).) |
| NF A50-435-1996 | 铝及铝合金.试验方法.板材和带材的凸耳试验 | (ALUMINIUM AND ALUMINIUM ALLOYS. TEST METHODS. EARING TEST FOR SHEET AND STRIP. (EUROPEAN STANDARD EN 1669).) |
| NF A50-437-1995 | 铝和铝合金.罐头、盒子和盖子的轧制品 | (Aluminium and aluminium alloys. Rolled products for cans, closures and lids. Specifications.) |
| NF A50-440-1996 | 铝和铝合金.薄金属片.第1部分:检验和交货的技术条件 | (Aluminium and aluminium alloys. Foil. Part 1 : technical conditions for inspection and delivery.) |
| NF A50-441-1996 | 铝和铝合金.第2部分:机械性能 | (Aluminium and aluminium alloys. Foil. Part 2 : mechanical properties.) |
| NF A50-442-1996 | 铝和铝合金.薄金属片.第3部分:尺寸公差 | (Aluminium and aluminium alloys. Foil. Part 3 : tolerances on dimensions.) |
| NF A50-443-1997 | 铝和铝合金.薄金属片.第4部分:特性要求 | (ALUMINIUM AND ALUMINIUM ALLOYS. FOILS. PART 4 : SPECIAL PROPERTY REQUIREMENTS. (EUROPEAN STANDARD EN 546-4).) |
| NF A50-452-1984 | 铝和铝合金.板状或带状涂漆产品.特性 | (Aluminium and aluminium alloys. Coil coating strip and sheet. Characteristics.) |
| NF A50-461-1996 | 铝及铝合金.散热片坯料.第2部分:机械性能 | (ALUMINIUM AND ALUMINIUM ALLOYS. FINSTOCK. PART 2 : MECHANICAL PROPERTIES. (EUROPEAN STANDARD EN 683-2).) |
| NF A50-462-1996 | 铝及铝合金.散热片坯料.第3部分:尺寸和形状公差 | (ALUMINIUM AND ALUMINIUM ALLOYS. FINSTOCK. PART 3 : TOLERANCES ON DIMENSIONS AND FORM. (EUROPEAN STANDARD EN 683-3).) |
| NF A50-470-1-2003 | 铝和铝合金.结构性铁路设施用制品.检查和交货的技术条件.第1部分:挤压制品 | (Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Part 1 : extruded products.) |
| NF A50-506-1982 | 铝和铝合金.用滚压机和压弯机冷成形型材.一般特性 | (Aluminium and aluminium alloys. Cold formed sections produced by cold rolling and by bending. General characteristics.) |
| NF A50-510-1994 | 铝和铝合金.从锻制产品中获取的冲击挤压加工用铝块.规范 | (Aluminium and aluminium alloys. Impact extrusion slugs obtained from wrought products. Specifications.) |
| NF A50-600-1994 | 铝和铝合金.适于挤压的挤压铸坯 | (ALUMINIUM AND ALUMINIUM ALLOYS. EXTRUSION INGOTS. SPECIFICATIONS. (EUROPEAN STANDARD EN 486).) |
| NF A50-616-1998 | 铝和铝合金.冷拉棒/棍和管.第7部分:无缝管.尺寸,公差和形状(欧洲标准EN754-7) | (Aluminium and aluminium alloys. Cold drawn rod/bar and tube. Part 7 : seamless tubes, tolerances on dimensions and form.) |
| NF A50-617-1998 | 铝及铝合金.冷拔棒材/条材和管材.第8部分:多孔拉拔管尺寸和形状公差 | (ALUMINIUM AND ALUMINIUM ALLOYS. COLD DRAWN ROD/BAR AND TUBE. PART 8 : PORTHOLE TUBES, TOLERANCES ON DIMENSIONS AND FORM. (EUROPEAN STANDARD EN 754-8).) |
| NF A50-620-2004 | 铝及铝合金.通用冷拉制圆盘管.规范 | (Aluminium and aluminium alloys - Cold drawn, round, coiled tube for general applications - Specification.) |
| NF A50-632-1995 | 铝和铝合金.挤压棒材/管材和型材.第三部分:挤压圆形棒材.尺寸和形状公差 | (Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles. Part 3 : round bars, tolerances on dimensions and form.) |
| NF A50-633-1995 | 铝和铝合金.挤压棒材/管材和型材.第四部分:挤压方形条材尺寸和形状和公差 | (ALUMINIUM AND ALUMINIUM ALLOYS. EXTRUDED ROD/BAR, TUBE AND PROFILES. PART 4 : SQUARE BARS, TOLERANCES ON DIMENSIONS AND FORM. (EUROPEAN STANDARD EN 755-4).) |
| NF A50-634-1995 | 铝和铝合金.挤压棒材/管材和型材.第五部分:挤压矩形棒材. 尺寸和形状公差 | (Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles. Part 5 : rectangular bars, tolerances on dimensions and form.) |
| NF A50-635-1995 | 铝和铝合金.挤压棒材,管材和型材.第六部分:挤压六角形条材.尺寸和形状公差 | (Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles. Part 6 : hexagonal bars, tolerances on dimensions and form.) |
| NF A50-636-1999 | 铝和铝合金.挤压棍棒,管和截面图.第7部分:无缝管尺寸公差和形状(欧洲标准EN755-7) | (Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles. Part 7 : seamless tubes, tolerances on dimensions and form.) |
| NF A50-637-1998 | 铝和铝合金.挤压棍/棒材,管和靠模.第8部分:钻头出水口管,尺寸和框架公差 | (ALUMINIUM AND ALUMINIUM ALLOYS. EXTRUDED ROD/BAR, TUBE AND PROFILES. PART 8 : PORTHOLE TUBES, TOLERANCES ON DIMENSIONS AND FORM. (EUROPEAN STANDARD EN 755-8).) |
| NF A50-638-9-2001 | 铝和铝合金.挤制棒材/杆材、管及型材.第9部分:型材的尺寸和形状公差 | (Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9 : profiles, tolerances on dimensions and form.) |
| NF A50-640-1-2001 | 铝及铝合金.挤制合金EN AW-6060 and EN AW-6063精密型材.第1部分:检验和交货技术条件 | (Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1 : technical conditions for inspection and delivery.) |
| NF A50-640-2-2001 | 铝及铝合金.挤制合金EN AW-6060 and EN AW-6063精密型材.第2部分:尺寸和形状公差 | (Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 2 : tolerances on dimensions and form.) |
| NF A50-645-2004 | 铝及铝合金.通用挤制圆盘管.规范 | (Aluminium and aluminium alloys - Extruded round, coiled tube for general applications - Specification.) |
| NF A50-650-2-1997 | 铝和铝合金.挤压棒材.电气设备的特殊要求 | (Aluminium and aluminium alloys. Drawing stock. Part 2 : specific requirements for electrical applications.) |
| NF A50-650-4-1997 | 铝和铝合金.挤压棒材.焊接设备的特殊要求 | (Aluminium and aluminium alloys. Drawing stock. Part 4 : specific requirements for welding applications.) |
| NF A50-701-1982 | 铝和铝合金.拉制线材.根据成分分类 | (Aluminium and aluminium alloys. Extruded and drawn products. Division into groups according to chemical composition.) |
| NF A50-703-1984 | 铝和铝合金.拉制方形棒材.尺寸公差和推荐尺寸 | (Aluminium and aluminium alloys. Square section extruded bars. Dimensional tolerances and recommended dimensions.) |
| NF A50-706-1987 | 铝和铝合金.Ｌ型截面拉制型材.尺寸公差和推荐尺寸 | (Aluminium and aluminium alloys. Angles. Dimension and form tolerances.) |
| NF A50-707-1981 | 铝和铝合金.Ｉ型截面拉制型材.尺寸公差和推荐尺寸 | (Aluminium and aluminium alloys. Extruded shapes : I beams. Tolerances and dimensions.) |
| NF A50-708-1982 | 铝和铝合金.Ｔ型截面拉制型材.尺寸公差和推荐尺寸 | (Aluminium and aluminium alloys. Extruded shape : tees. Tolerances and dimensions.) |
| NF A50-709-1981 | 铝和铝合金.Ｕ型截面拉制型材.尺寸公差和推荐尺寸 | (Aluminium and aluminium alloys. Extruded shapes ; channels. Tolerances and dimensions.) |
| NF A50-802-1988 | 铝和铝合金.大直径焊接管.尺寸和公差 | (ALUMINIUM AND ALUMINIUM ALLOYS. LARGE DIAMETER WELDED TUBES. DIMENSIONS AND TOLERANCES.) |
| NF A50-821-1971 | 铝和铝合金.冷滚轧成形型材.尺寸和尺寸公差 | (ALUMINIUM AND ALUMINIUM ALLOYS. COLD FORMED SECTIONS PRODUCED BY COLD ROLLING. DIMENSIONS AND TOLERANCES.) |
| NF A50-825-1971 | 铝和铝合铝.冷弯成形型材.尺寸公差 | (ALUMINIUM AND ALUMINIUM ALLOYS. COLD FORMED SECTIONS OBTAINED BY BENDING. DIMENSION TOLERANCES.) |
| NF A50-910-1997 | 铝及铝合金.铸锻造坯料.第1部分:检查和交货技术条件(欧洲标准EN 604-1) | (ALUMINIUM AND ALUMINIUM ALLOYS. CAST FORGING STOCK. PART 1 : TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY. (EUROPEAN STANDARD EN 604-1).) |
| NF A50-911-1997 | 铝及铝合金.铸锻造坯料.第2部分:尺寸和形状公差(欧洲标准EN 604-2) | (ALUMINIUM AND ALUMINIUM ALLOYS. CAST FORGING STOCK. PART 2 : TOLERANCES ON DIMENSIONS AND FORM. (EUROPEAN STANDARD EN 604-2).) |
| NF A50-920-1996 | 铝及铝合金.锻造坯料.第1部分:检验和交货的技术条件 | (ALUMINIUM AND ALUMINIUM ALLOYS. WROUGHT FORGING STOCK. PART 1 : TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY. (EUROPEAN STANDARD EN 603-1).) |
| NF A50-921-1996 | 铝及铝合金.锻造坯料.第2部分:机械性能 | (ALUMINIUM AND ALUMINIUM ALLOYS. WROUGHT FORGING STOCK. PART 2 : MECHANICAL PROPERTIES. (EUROPEAN STANDARD EN 603-2).) |
| NF A50-922-2000 | 铝及铝合金.锻造坯料.第3部分:尺寸和形状公差 | (Aluminium and aluminium alloys - Wrought forging stock - Part 3 : tolerances on dimensions and form.) |
| NF A50-931-1994 | 锻铝和铝合金锻件.第2部分:机械特性和附加特性要求 | (Aluminium and aluminium alloys. Forgings. Part 2 : mechanical properties and additional property requirements.) |
| NF A50-932-3-2002 | 铝和铝合金.锻造.第3部分:尺寸和形式公差 | (Aluminium and aluminium alloys - Forgings - Part 3 : tolerances on dimensions and form.) |
| NF A57-100-1994 | 铸铝合金.用于生产与食品接触的材料和物品的金属的化学成分 | (Aluminium and aluminium alloys. Castings. Chemical composition of castings for use in contact with food.) |
| NF A57-110-1995 | 铝和铝合金.液体金属.规范 | (ALUMINIUM AND ALUMINIUM ALLOYS. LIQUID METAL. SPECIFICATIONS. (EUROPEAN STANDARD EN 577).) |
| NF A57-130-1996 | 铝及铝合金.冶炼用合金锭.规范(欧洲标准EN 1676) | (Aluminium and aluminium alloys. Alloyed ingots for remelting. Specifications.) |
| NF A57-140-1995 | 铝和铝合金.通过熔化制造的母合金.规范 | (Aluminium and aluminium alloys. Master alloys produced by melting. Specifications.) |
| NF A57-220-1998 | 铝和铝合金.铸件.化学成分和机械性能(欧洲标准EN 1706) | (Aluminium and aluminium alloys. Castings. Chemical composition and mechanical properties.) |
| NF A66-002-1985 | 铸造产品.铝合金和锌合金.压力铸件的尺寸公差 | (Foundry products. Aluminium alloys and zinc alloys. Cast products. Dimensional tolerances for pressure die castings.) |
| NF A81-331-1984 | 焊接、硬钎焊和硬焊铝及铝合金用填充金属材料.符号.规范 | (Filler materials for welding, brazing and braze welding aluminium and aluminium alloys. Symbolization. Specifications.) |
| NF A81-410-1984 | 铝和铝合金.焊接、硬钎焊和钎焊.基础产品和焊条的选择 | (ALUMINIUM AND ALUMINIUM ALLOYS. WELDING,BRAZING AND BRAZE WELDING. BASE MATERIALS AND SELECTION OF FILLER MATERIALS.) |
| NF A81-900-1973 | 铝和铝合金.焊接.焊剂的使用和检查 | (ALUMINIUM AND ALUMINIUM ALLOYS. WELDING. USE AND TESTING OF WELDING FLUXES.) |
| NF A87-010-1973 | 铝和铝合金.焊接.边的准备 | (ALUMINIUM AND ALUMINIUM ALLOYS. WELDING. WELD PREPARATIONS.) |
| NF A87-013-3-2001 | 焊接和相关工艺.接头预处理的推荐方法.第3部分:铝和铝合金的金属焊条惰性气体保护焊和钨极惰性气体保护焊 | (Welding and allied processes - Recommendations for joint preparation - Part 3 : metal inert gas welding and tungsten inert gas welding of aluminium and its alloys.) |
| NF A88-110-2-1992 | 焊工合格鉴定.熔焊.第2部分:铝及铝合金件 | (Approval testing of welders. Fusion welding. Part 2 : aluminium and aluminium alloys.) |
| NF A89-101-4-2000 | 焊接.金属材料焊接的推荐方法.第4部分:铝和铝合金的电弧焊 | (Welding - Recommendations for welding of metallic materials - Part 4 : arc welding of aluminium and aluminium alloys.) |
| NF A89-220-1973 | 铝和铝合金.焊接.分类和焊接点的检验 | (ALUMINIUM AND ALLOY THEREOF. WELDING. CLASSIFICATION AND TESTING OF WELDED JOINTS.) |
| NF A89-232-1994 | 铝和可焊合金的弧焊接头.质量缺陷等级导则 | (ARC-WELDED JOINTS IN ALUMINIUM AND ITS WELDABLE ALLOYS. GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS. (EUROPEAN STANDARD EN 30042).) |
| NF A89-234-2001 | 焊接.电子和激光束焊接接头.缺陷的质量级别导则.第1部分:铝及其可焊合金 | (Welding - Electron and laser beam welded joints - Guidance on quality levels for imperfections - Part 2 : aluminium and its weldable alloys.) |
| NF A89-310-1973 | 铝和铝合金.焊接.基本元件的连接.选择原则 | (ALUMINIUM AND ALUMINIUM ALLOYS. WELDING. ELEMENTARY TYPES OF ASSEHBLY. SELECTION CRITERIA.) |
| NF A91-400-1987 | 表面处理.铝及铝合金的阳极极处理.词汇 | (Anodizing of aluminium and its alloys. Vocabulary.) |
| NF A91-401-1966 | 金属表面处理.铝和铝合金的阳极处理.(阳极氧化).试验方法的名称 | (SURFACE TREATMENT OF METALS. ANODISATION (ANODIC OXIDATION) OF ALUMINIUM AND ITS ALLOYS. NOMENCLATURE OF TEST METHODS.) |
| NF A91-402-1981 | 铝和铝合金的阳极处理.(阳极氧化).厚度的测量.剖面的显微照相 | (Surface treatments of metals. Anodic oxidation of aluminium and its alloys. Thickness measurements.) |
| NF A91-404-1966 | 金属表面处理.铝和铝合金的阳极处理.(阳极氧化).厚度的测量 | (SURFACE TREATMENT OF METALS. ANODIZING (ANODIC OXYDIZING) OF ALUMINIUM AND ITS ALLOYS. MEASUREMENT OF THICKNESS.) |
| NF A91-407-1981 | 铝和铝合金的阳极处理.(阳极氧化).通过测量在酸溶液浸泡后重量的损失来进行积砂的检验 | (Anodizing of aluminium and its alloys. Assessment of sealing quality by measurement of the loss of mass after immersion in acid solution.) |
| NF A91-408-1985 | 铝和阳极化的铝合金.沉砂检验.SANODALG兰滴定试验 | (Anodized aluminium and aluminium alloys. Assessment of sealing quality. Sanodal “G“ blue drop test.) |
| NF A91-411-1966 | 金属表面处理.铝和铝合金的阳极处理.耐腐蚀的检验 | (SURFACE TREATMENT OF METALS. ANODISATION (ANODIC OXIDATION) OF ALUMINIUM AND ITS ALLOYS. CHECK OF CORROSION RESISTANCE.) |
| NF A91-412-1982 | 铝和铝合金的阳极处理.彩色氧化层耐人造光的加速试验 | (Anodizing of aluminium and its alloys. Accelerated test of light fastness of coloured anodic oxide coatings to artificial light.) |
| NF A91-420-1988 | 表面处理.阳极氧化铝和铝合金.45°镜面反射率.总反射率.成象清晰度 | (Surface treatments. Anodized aluminium and aluminium alloys. Specular reflectance at 45 degrees. Total reflectance. Image clarity.) |
| NF A91-423-1988 | 表面处理.铝和阳极氧化的铝合金.总反射率的测定.光电反射计法 | (Surface treatments. Anodized aluminium and aluminium alloys. Measurement of total reflectivity using a photoelectric reflectometer.) |
| NF A91-450-1981 | 铝及其合金的阳极氧化.铝的阳极氧化物镀层的一般规范 | (Anodizing of aluminium and its alloys. General specifications for anodic oxide coatings on aluminium.) |
| NF A91-455-1-2001 | 铝及铝合金.阳极氧化.第1部分:铝上装饰和保护用阳极氧化覆层的规定方法 | (Aluminium and aluminium alloys - Anodizing - Part 1 : method for specifying decorative and protective anodic oxidation coatings on aluminiurm.) |
| NF A91-455-10-1999 | 铝和铝合金.阳极化.第10部分:使用磨损喷射试验装置对阳极氧化物镀膜的主要特定磨损抗性的测定 | (Aluminium and aluminium alloys. Anodizing. Part 10 : measurement of mean specific abrasion resistance of anodic oxidation coatings using an abrasive jet test apparatus.) |
| NF A91-455-11-2000 | 铝和铝合金.阳极化.第11部分:在20度、45度、60度或85度时测定阳极氧化物涂层的镜面反射和镜面毛重 | (Aluminium and aluminium alloys - Anodizing - Part 11 : measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 o, 45 o, 60 o or 85 o.) |
| NF A91-455-12-2000 | 铝和铝合金.阳极化.第12部分:用集成球形仪器测量铝表面反射特性 | (Aluminium and aluminium alloys - Anodizing - Part 12 : measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments.) |
| NF A91-455-13-2000 | 铝和铝合金.阳极化.第13部分:用滤光测角仪测量铝表面反射特性 | (Aluminium and aluminium alloys - Anodizing - Part 13 : measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer.) |
| NF A91-455-14-2000 | 铝和铝合金.阳极化.第14部分:用肉眼确定阳极氧化物涂层的图像清晰度.图表比例尺法 | (Aluminium and aluminium alloys - Anodizing - Part 14 : visual determination of image clarity of anodic oxidation coatings - Chart scale method.) |
| NF A91-455-15-2000 | 铝和铝合金.阳极化.第15部分:阳极氧化物涂层抗变形断裂的测定 | (Aluminium and aluminium alloys - Anodizing - Part 15 : assessment of resistance of anodic oxidation coatings to cracking by deformation.) |
| NF A91-455-16-2001 | 铝及铝合金.阳极氧化.第16部分:阳极氧化覆层连续性检查.硫酸铜试验 | (Aluminium and aluminium alloys - Anodizing - Part 16 : check for continuity of thin anodic oxydation coatings - Copper sulfate test.) |
| NF A91-455-17-2001 | 铝及铝合金.阳极氧化.第17部分:电介质击穿潜能的测定 | (Aluminium and aluminium alloys - Anodizing - Part 17 : determination of electric breakdown potential.) |
| NF A91-455-18-2001 | 铝和铝合金.阳极氧化.第18部分:点腐蚀评定用额定值系统.图表法 | (Aluminium and aluminium alloys - Anodizing - Part 18 : Rating system for the evaluation of pitting corrosion - Chart method.) |
| NF A91-455-19-2002 | 铝及铝合金.阳极氧化.第19部分:斑蚀评定的等级系统.格栅法 | (Aluminium and aluminium alloys - Anodizing - Part 19 : rating system for the evaluation of pitting corrosion - Grid method.) |
| NF A91-455-2-1999 | 铝和铝合金.阳极化.第2部分:阳极氧化物镀膜单位面积质量的测定(表面密度).重量计法(欧洲标准EN 12373-2) | (Aluminium and aluminium alloys. Anodizing. Part 2 : determination of mass per unit area (surface density) of anodic oxidation coatings. Gravimetric method.) |
| NF A91-455-3-1999 | 铝和铝合金.阳极化.第3部分:阳极氧化物镀膜厚度的测定.用分裂束显微镜的非损测量(欧洲标准EN 12373-3) | (Aluminium and aluminium alloys. Anodizing. Part 3 : determination of thickness of anodic oxidation coatings. Non-destructive measurement by split-beam microscope.) |
| NF A91-455-5-1999 | 铝和铝合金.阳极化.第5部分:用验收测量的密封阳极氧化物镀膜质量评估(欧洲标准EN 12373-5) | (Aluminium and aluminium alloys. Anodizing. Part 5 : assessment of quality of sealed anodic oxidation coatings by measurement of admittance.) |
| NF A91-455-6-1999 | 铝和铝合金.阳极化.第6部分:通过对未预先进行酸处理的浸入到磷酸/铬酸溶液中的质量损失的测量对密封阳极氧 | (Aluminium and aluminium alloys. Anodizing. Part 6 : assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution without prior acid treatment.) |
| NF A91-455-7-2002 | 铝及铝合金.阳极氧化.第7部分:测量经过磷酸和铬酸溶液酸处理浸渍后的质量损失来评定密封阳极氧化覆层的质量 | (Aluminium and aluminium alloys - Anodizing - Part 7 : assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solut) |
| NF A91-455-8-1999 | 铝和铝合金.阳极化.第8部分:紫外灯和有色阳极氧化物加热镀膜的相对固定性测定.(欧洲标准EN 12373-8) | (Aluminium and aluminium alloys. Anodizing. Part 8 : determination of the comparative fastness to ultra-violet light and heat of coloured anodic oxidation coatings.) |
| NF A91-455-9-1999 | 铝和铝合金.阳极化.第9部分:使用磨擦轮磨损试验的阳极氧化物镀膜的磨损抗性和磨损指数的测定 | (Aluminium and aluminium alloys. Anodizing. Part 9 : measurement of wear resistance and wear index of anodic oxidation coatings using an abrasive wheel wear test apparatus.) |
| NF A91-473-2001 | 锌、镉、铝锌合金和锌铝合金的铬酸盐转化涂层.试验方法 | (Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys - Test methods.) |
| NF A91-477-2000 | 金属的防腐蚀.经清洗和没有清洗的铝及铝合金上的铬酸盐转化涂层 | (Corrosion protection of metals - Rinsed and non-rinsed chromate conversion coatings on aluminium and aluminium alloys.) |
| NF A92-020-1990 | 铝和铝合金用的搪瓷涂层.试样的制备 | (VITREOUS AND PORCELAIN ENAMELS FOR ALUMINIUM AND ALUMINIUM ALLOYS. PREPARATION OF TEST SAMPLES.) |
| NF A92-021-1990 | 铝和铝合金用的搪瓷涂层.附着力试验 | (VITREOUS AND PORCELAIN ENAMELS FOR ALUMINIUM AND ALUMINIUM LLOYS. ADHESION TESTS.) |
| NF B40-001-1-1998 | 密实成型耐火产品的分类.第1部分:铝硅产品 | (Classification of dense shaped refractory products. Part 1 : alumina-silica products.) |
| NF B42-001-1997 | 高技术陶瓷.陶瓷粉末的试验方法.第1部分:铝中杂质的测定(欧洲标准EN 725-1) | (Advanced technical ceramics. Methods of test for ceramic powders. Part 1 : determination of impurities in alumina.) |
| NF B49-421-1990 | 耐火材料制品.铝矾土、硅质材料、碳化硅、碳和金属硅耐火材料制品的化学分析 | (REFRACTORY PRODUCTS. CHEMICAL ANALYSIS OF ALUMINOUS,SILICEOUS,SILICON CARBIDE,CARBON AND METALLIC SILICON REFRACTORY PRODUCTS.) |
| NF C20-131-1974 | 铝导线用带导电镀层的有铝片或铜片的接头.规则和尺寸 | (LUGS WITH COPPER OR ALUMINIUM FLATS AND WITH CONDUCTING COATING FOR ALUMINIUM CONDUCTORS. REQUIREMENTS AND DIMENSIONS.) |
| NF C31-003-2000 | 特种绕组线规范.第0部分:一般要求.第3节:漆包圆铝线 | (Specification for particular types of winding wires - Part 0 : general requirements - Section 3 : enamelled round aluminium wire.) |
| NF C31-003/A1-2001 | 特种绕组线规范.第0-3部分:一般要求.漆包圆铝线 | (Specifications for particular types of winding wires - Part 0-3 : general requirements - Enamelled round aluminium wire.) |
| NF C31-122-1980 | 电气构件中的导体.圆截面四分之三冷锻硬裸铝线.特性 | (WIRES FOR ELECTRICAL MACHINERY AND APPARATUS. ROUND BARE 3/4 HARD ALUMINIUM WIRE. CHARACTERISTICS.) |
| NF C31-520-1979 | 电路或仪表盘用铝和铝合金扁条线 | (Flat aluminium and aluminium alloys bars for switchboards and electrical wirings (with rounded edges).) |
| NF C31-664-1995 | 特种绕组线规范.第14部分:105级聚乙烯醇乙醛漆包圆铝绕组线 | (Specifications for particular types of winding wires. Part 14 : polyvinyl acetal enamelled round aluminium wire, class 105.) |
| NF C31-664/A1-2001 | 特种绕组线规范.第14部分:聚乙烯醇漆绝缘的圆铝线,等级105 | (Specifications for particular types of winding wires - Part 14 : polyvinyl acetal enamelled round aluminium wire, class 105.) |
| NF C31-665-1995 | 特种绕组线规范.第15部分:180级聚酰胺酯漆包圆铝绕组线 | (Specifications for particular types of winding wires. Part 15 : polyesterimide enamelled round aluminium wire, class 180.) |
| NF C31-665/A1-2001 | 特种绕组线规范.第15部分:聚酰脂亚胺漆绝缘圆铝线,等级180 | (Specifications for particular types of winding wires - Part 15 : polyesterimide enamelled round aluminium wire, class 180.) |
| NF C31-674-1995 | 特种绕组线规范.第24部分:涂覆聚酰胺的聚酯或聚酰胺酯漆包圆铝绕组线,180级 | (Specifications for particular types of winding wires. Part 24 : polyester or polyesterimide enamelled round aluminium wire overcoated with polyamide, class 180.) |
| NF C31-674/A1-2001 | 特种绕组线规范.第24部分:聚酰胺涂层的180级聚酯或聚酯亚胺漆包圆铝线 | (Specifications for particular types of winding wires - Part 24 : polyester or polyesterimide enamelled round aluminium wire overcoated with polyamide, class 180.) |
| NF C31-675-1998 | 特种绕组线规范.第25部分:涂覆聚酰胺-酰亚胺酯的聚亚酰胺酯漆包圆铝绕组线,200级 | (Specifications for particular types of winding wires. Part 25 : polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200.) |
| NF C31-675/A2-2001 | 特种绕组线规范.第25部分:涂覆聚酰胺-酰亚胺酯的200级聚酯或聚酯亚胺漆包圆铝线 | (Specifications for particular types of winding wires - Part 25 : polyester or polyesterimide overcoated with polyamid-imide enamelled round aluminium wire, class 200.) |
| NF C32-208-1985 | 设备用绝缘电缆和导线.额定电压４５０/ ７５０V的聚氯乙烯绝缘导线.用铝作硬质心线.国家２类型号系列 | (INSULATED CABLES AND FLEXIBLE CORDS FOR INSTALLATIONS. PVC INSULATED SINGLE-CORE NON SHEATHED CABLES WITH RIGID STRANDED ALUMINIUM CONDUCTOR OF RATED VOLTAGES 450/750 V. SERIES OF THE NATIONAL TYPE OF CATEGORY 2.) |
| NF C32-2081-1991 | 设备用绝缘电缆和导线.额定电压达450/750V的带钢性铝芯的用聚氯乙烯绝缘导线的国家级型号系列 | () |
| NF C34-111-1998 | 架空线导体用冷拉铝线 | (Hard-drawn aluminium wire for overhead line conductors.) |
| NF C34-112-2001 | 架空电力导线.铝镁硅合金线 | (Conductors for overhead lines - Aluminium-magnesium-silicon alloy wires.) |
| NF C34-114-1996 | 电气设备用铝包钢丝 | (Aluminium-clad steel wires for electrical purposes.) |
| NF C34-114/A11-2001 | 电气设备用包铝钢丝 | (Aluminium-clad steel wires for electrical purposes.) |
| NF C63-061-1973 | 导线的连接（其中至少一根是铝或铝合金绝缘导线）的连接.电气试验规则 | (LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR. CONNECTION JOINTS FOR CONDUCTORS. ONE AT LEAST OF THEM BEING AND INSULATED. ALUMINIUM OR ALUMINIUM ALLOY CONDUCTOR. ELECTRICAL TEST REQUIREMENTS.) |
| NF C64-450-1987 | 充气式高压开关及控制设备用铝合金浇铸外壳 | (Cast aluminium alloy enclosures for gas-filled high-voltage swichtgear and controlgear.) |
| NF C64-451-1990 | 高压充气开关和控制装置用铝和铝合金煅制外壳.(欧洲标准 EN 50064) | (Wrought aluminium and aluminium alloy enclosures for gas-filled high-voltage switchgear and controlgear.) |
| NF C64-4511-1993 | 置于气体压力下的高压装置用铝和铝合金煅制外壳.(欧洲标准 EN 50064).补充件1 | () |
| NF C64-452-1992 | 充气高压开关和控制设备用锻铝和铸铝合金焊接复合外壳 | (Welded composite enclosures of cast and wrought aluminium alloys for gas-filled high-voltage switchgear and controlgear.) |
| NF C64-4521-1993 | 充气高压开关和控制设备用锻铝和铸铝合金焊接复合外壳.补充件1 | () |
| NF C83-110-1981 | 电子元器件质量评定协调体系.分规范.铝电解质电容器 | (Harmonized system of quality assessment for electronic components. Sectional specification. Aluminium electrolytic capacitors.) |
| NF C93-110-1971 | 铝固定电解质电容器.一般规定 | (COMPONENTS FOR ELECTRONIC EQUIPMENT. FIXED ALUMINIUM ELECTRONIC CAPACITORS. GENERAL REQUIREMENTS.) |
| NF C93-110M1-1973 | 电子元件.铝制固定电解电容器.一般要求 | (COMPONENTS FOR ELECTRONIC EQUIPMENT. FIXED ALUMINIUM ELECTRONIC CAPACITORS. GENERAL REQUIREMENTS.) |
| NF C93-110M2-1974 | 电子元件.铝制固定电解电容器.一般要求 | (COMPONENTS FOR ELECTRONIC EQUIPMENT. FIXED ALUMINIUM ELECTROLYTIC CAPACITORS. GENERAL REQUIREMENTS.) |
| NF C93-110M3-1975 | 电子元件.铝制固定电解电容器.一般要求 | (COMPONENTS FOR ELECTRONIC EQUIPMENT. FIXED ALUMINIUM ELECTROLYTIC CAPACITORS. GENERAL REQUIREMENTS.) |
| NF E22-555-1985 | 滑动轴承.整体轴承用的铝合金 | (Plain bearings. Aluminium alloy for solid bearings.) |
| NF E29-200-4-2002 | 法兰及其连接件.按PN标注的管、阀门、配件和附件用圆形法兰.第4部分:铝合金法兰 | (Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4 : aluminium alloy flanges.) |
| NF E29-465-1986 | 工业阀门.旋转阀.铜铝球阀.规范 | (INDUSTRIAL VALVES. CUPRO-ALUMINIUM BALL VALVES. SPECIFICATION.) |
| NF E29-745-2000 | 便携式气瓶.可再充气的便携式焊接铝合金气瓶的设计和结构规范 | (Transportable gas cylinders - Specification for the design and construction of refillable transportable welded aluminium alloy gas cylinders.) |
| NF E29-762-1990 | 气瓶.无缝铝合金瓶.腐蚀试验 | (GAS VESSELS. ALUMINIUM ALLOY SEAMLESS GAS CYLINDERS. CORROSION TESTS.) |
| NF E82-110-1982 | 铝和铝合金模锻零件.供货一般技术条件 | (ALUMINIUM AND ALUMINIUM ALLOY DROP FORGINGS. GENERAL TECHNICAL DELIVERY CONDITIONS.) |
| NF F01-820-1992 | 铁路车辆.车身用铝合金焊接接头(焊缝) | (RAILWAY ROLLING STOCK. WELDED JOINTS OF PRODUCTS IN ALUMINIUM ALLOY FOR BODYWORK. CHARACTERIZATION.) |
| NF F11-042-1994 | 装空气或氮气用的一般不近火的压力容器.第4部分:用于铁路运输车辆空气制动和辐助气动设备的铝合金压力容器 | (Simple unfired pressure vessels designed to contain air or nirogen. Part 4 : aluminium alloy pressure vessels designed for air braking equipment and auxiliary penumatic equipment for railway rolling stock.) |
| NF F19-303-1996 | 铁路车辆.铝和铝合金用含水涂料单分子薄膜 | (RAILWAY ROLLING STOCK. PAINT MONOCOAT WATERBORNE WITH WATER USED TO ALUMINIUM AND ALUMINIUM`S ALLOIES.) |
| NF F19-350-1998 | 铁路滚动存货车.线圈涂层板铝和铝合金 | (RAILWAY ROLLING STOCK. COIL COATED SHEETS ALUMINIUM AND ALUMINIUM ALLOYS.) |
| NF F50-105-1992 | 铁路固定设备.钢轨铝热剂焊接.工作特性和验收 | (RAILWAY FIXED EQUIPMENT. THERMIT WELDING OF RAILS. WELDS PERFORMED BY COMPAGNIES. PERFORMANCE AND ACCEPTANCE CONDITONS OF WORKS.) |
| NF F55-310-1993 | 铁路固定设备.铝合金信号用柱式支架和门架式结构 | (RAILWAY FIXED EQUIPMENT. POST BRACKETS AND PORTAL STRUCTURES FOR SIGNALLING IN ALUMINIUM ALLOY.) |
| NF F61-021-1990 | 铁路车辆.用于铝制导电引线的螺纹接头.上紧力矩 | (RAILWAY ROLLING STOCK. SCREWED JOINT FOR ELECTRICAL ALUMINIUM CONNCECTIONS DRIVING TORQUE.) |
| NF F80-153-1986 | 通用铁路设备.扁平产品的冷弯半径.铝和铝合金板和带喷漆产品的最小弯曲半径 | (RAILWAY EQUIPMENT. COLD FOLDING RADII FOR PLAT PRODUCTS. MINIMUM FOLDING RADII FOR LAQUERED SHEETS OR BANDS MADE OF ALUMINIUM AND ALUMINIUM ALLOYS.) |
| NF F82-001-1990 | 铁路车辆.车体框架用的可焊接铝合金线材 | (RAILWAY ROLLING STOCK. EXTRUDED WELDABLE PRODUCTS IN ALUMINIUM ALLOY FOR BODYWORK.) |
| NF G07-019-1-1996 | 纺织品.色牢度试验.第X01部分:耐碳化色牢度.氯化铝法 | (Textiles. Tests for colour fastness. Part X01 : colour fastness to carbonizing : aluminium chloride.) |
| NF G52-209-1976 | 皮革.皮革的化学分析.氧化铝（Ａｌ2 Ｏ3 ）含量的测定 | (LEATHERS AND HIDES. CHEMICAL TESTING OF LEATHER. DETERMINATION OF ALUMINIUM OXIDE (AL203).) |
| NF H34-055-1998 | 包装.柔性铝管.壁厚度测量法 | (PACKAGING. FLEXIBLE ALUMINIUM TUBES. WALL THICKNESS DETERMINATION METHOD. (EUROPEAN STANDARD EN 12375).) |
| NF H34-056-2000 | 包装.柔性铝管.内喷漆膜测量方法 | (Packaging - Flexibles aluminium tubes - Internal lacquer film measurement method.) |
| NF H44-006-1988 | 烟雾发生器.压力分配用铝和铝合金容器（气雾剂容器型）与膨胀管联系的底部尺寸公差 | (AEROSOL DISPENSERS. CONTAINERS IN ALUMINIUM AND ALLOYS. TOLERANCES OF THE FUNDAMENTAL DIMENSIONS IN CONNECTION WITH THE CLINCH.) |
| NF H44-016-1988 | 烟雾发生器.压力分配容器（气雾剂容器型）.铝制２０mm容器瓶口尺寸 | (AEROSOL DISPENSERS. ALUMINIUM MONOBLOC CONTAINERS. DIMENSIONS OF THE 20 MM FINISH.) |
| NF H44-017-1988 | 烟雾发生器.金属容器.铝制２５．４mm容器尺寸 | (AEROSOL DISPENSERS. METAL CONTAINERS. DIMENSIONS OF ALUMINIUM MONOBLOC CONTAINERS WITH 25,4 MM APERTURE.) |
| NF H44-038-1986 | 烟雾剂发生器.金属容器.２０mm瓶口铝制容器尺寸 | (AEROSOLS DISPENSERS. METAL CONTAINERS. DIMENSIONS OF ALUMINIUM MONOBLOC CONTAINERS WITH FINISH 20 MM.) |
| NF J13-005-1968 | 造船.铝和铝合金.轧制和拉制产品.可用合金表 | (SHIPBUILDING. ALUMINIUM AND ALUMINIUM ALLOYS. ROLLED AND DRAWN PRODUCTS. LIST OF USEABLE ALLOYS.) |
| NF J95-046-3-2002 | 小艇.外壳构造和建材尺寸.第3部分:材料:钢、铝合金、木材和其它材料 | (Small craft - Hull constructions and scantlings - Part 3 : materials : steel, aluminium alloys, wood, other materials.) |
| NF L06-380-20-2003 | 航空航天系列.航空航天结构用焊接及铜焊组件.材料的可焊接性和可铜焊接性.第20部分:均质铝及铝合金组件 | (Aerospace series - Aerospace series - Welded and brazed assemblies for aerospace constructions - Weldability and brazeability of materials - Part 20 : homogeneous assemblies aluminium and aluminium al) |
| NF L06-510-1983 | 航空和航天工业中铝合金数据处理用带尾柄圆柱形双刃铣刀的选择 | (Selection of end mills with shanks to be used in aerospace industry for numerical control machining of aluminium alloys.) |
| NF L07-152-1974 | 铝合金铆钉直径图形符号的表示 | (SYMBOLIC REPRESENTATION ON DRAWINGS OF RIVET DIAMETERS MADE OF ALUMINIUM ALLOYS.) |
| NF L10-270-1-1993 | 航空和航天系列.铝和铝合金产品的试验方法.第1部分:锻铝合金产品的导电性测定 | (Aerospace series. Test methods for aluminium and aluminium alloy products. Part 1 : determination of electrical conductivity of wrought aluminium alloy products.) |
| NF L10-270-5-1993 | 航空和航天系列.铝和铝合金产品的试验方法.第5部分:包层半成品的包层厚度及铜分散度的测定 | (Aerospace series. Test methods for aluminium and aluminium alloy products. Part 5 : determination of cladding thickness and copper diffusion of clad semi-finished products.) |
| NF L10-309-1997 | 航空和航天系列硫酸铬中铝和铝合金的酸洗 | (AEROSPACE SERIES. CHROMIC-SULPHURIC ACID PICKLE OF ALUMINIUM AND ALUMINIUM ALLOYS. (EUROPEAN STANDARD EN 2334).) |
| NF L10-310-1992 | 航空航天系列.铝和锻压铝合金的铬酸阳极化 | (AEROSPACE SERIES. CHROMIC ACID ANODIZING OF ALUMINIUM AND WROUGHT ALUMINIUM ALLOYS. (EUROPEAN STANDARD EN 2101).) |
| NF L10-311-1995 | 航天航空系列.铝合金的淬硬阳极极化 | (AEROSPACE SERIES. HARD ANODIZING OF ALUMINIUM ALLOYS. (EUROPEAN STANDARD EN 2536).) |
| NF L10-315-1992 | 航空航天系列.铝和锻压铝合金的硫阳极化 | (Aerospace series. Sulphuric acid anodizing of aluminium and wrought aluminium alloys.) |
| NF L10-316-2002 | 航空航天系列.铝及铝合金用铬酸盐转化膜(黄色) | (Aerospace series - Chromate conversion coatings (yellow) for aluminium and aluminium alloys.) |
| NF L10-600-1-1990 | 航空和航天系列.铝和铝合金锻制半成品.技术规范.第1部分:一般要求 | (AEROSPACE SERIES. ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PRODUCTS. TECHNICAL SPECIFICATION. PART 1 : GENERAL REQUIREMENTS. (EUROPEAN STANDARD EN 2070-1).) |
| NF L10-600-11-1993 | 航空和航天系列.铝和铝合金锻制半成品.技术规范.第1部分:一般要求.补充件1 | () |
| NF L10-600-2-1990 | 航空和航天系列.铝合铝合金锻制半成品.技术规范.第2部分:薄板、带材、弯曲的型材和厚板 | (AEROSPACE SERIES. ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PRODUCTS. TECHNICAL SPECIFICATION. PART 2 : SHEET,STRIP,FORMED PROFILES AND PLATE. (EUROPEAN STANDARD EN 2070-2).) |
| NF L10-600-3-1990 | 航空和航天系列.铝合铝合金锻制半成品.技术规范.第3部分:棒材和型材 | (AEROSPACE SERIES. ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PRODUCTS. TECHNICAL SPECIFICATION. PART 3 : BAR AND SECTION. (EUROPEAN STANDARD EN 2070-3).) |
| NF L10-600-4-1990 | 航空和航天系列.铝和铝合金锻制半成品.技术规范.第4部分:结构用管子 | (AEROSPACE SERIES. ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PROUDCTS. TECHNICAL SPECIFICATION. PART 4 : TUBE FOR STRUCTURES. (EUROPEAN STANDARD EN 2070-4).) |
| NF L10-600-5-1990 | 航空和航天系列.铝合铝合金锻制半成品.技术规范.第5部分:压力管 | (AEROSPACE SERIES. ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PRODUCTS. TECHNICAL SPECIFICATION. PART 5 : TUBE USED UNDER PRESSURE. (EUROPEAN STANDARD EN 2070-5).) |
| NF L10-600-6-1990 | 航空和航天系列.铝合铝合金锻制半成品.技术规范.第6部分.铆接线 | (AEROSPACE SERIES. ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PRODUCTS. TECHNICAL SPECIFICATION. PART 6 : RIVET WIRE. (EUROPEAN STANDARD EN 2070-6).) |
| NF L10-600-7-1990 | 航空和航天系列.铝合铝合金锻制半成品.技术规范.第7部分:锻工场用的锻造产品 | (AEROSPACE SERIES. ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PRODUCTS. TECHNICAL SPECIFICATION. PART 7 : WROUGHT FORGING STOCK. (EUROPEAN STANDARD EN 2070-7).) |
| NF L10-601-2-1990 | 航空和航天系列.铝合金和镁合金铸件和铸锭.技术说明.第2部分:重熔用锭.(欧洲标准EN 2076-2) | (AEROSPACE SERIES. ALUMINIUM AND MAGNESIUM ALLOY INGOTS AND CASTINGS. TECHNICAL SPECIFICATION. PART 2 : INGOTS FOR REMELTING. (EUROPEAN STANDARD EN 2076-2).) |
| NF L10-602-1-1990 | 航空和航天系列.锻造产品、锻件和铝合金模锻.技术规范.第１部分：一般要求 | (Aerospace series. Aluminium alloy forging stock and forgings. Technical specification. Part 1 : general requirements.) |
| NF L10-602-11-1993 | 航空和航天系列. 锻造产品、锻件和铝合金模锻.技术规范.第１部分：一般要求(欧洲标准EN 2082-1的补充件) | () |
| NF L10-602-2-1990 | 航空和航天系列.锻造产品、锻件和铝合金模锻.技术规范.第2部分:锻造产品 | (Aerospace series. Aluminium alloy forging stock and forgings. Technical specification. Part 2 : forging stock.) |
| NF L10-602-3-1990 | 航空和航天系列.锻造产品、锻件和铝合金模锻.技术规范.第3部分:锻件系列和锻件型号 | (AEROSPACE SERIES. ALUMINIUM ALLOY FORGING STOCK AND FORGINGS. TECHNICAL SPECIFICATION. PART 3 : PRE-PRODUCTION AND PRODUCTION FORGINGS. (EUROPEAN STANDARD EN 2082-3).) |
| NF L13-215-2002 | 航空航天系列.铝合金AL-W42201.焊接用填充金属.焊条 | (Aerospace series - Aluminium alloy AL-W42201 - Filler metal for welding - Rod.) |
| NF L13-232-2001 | 航空航天系列.铝合金AL-W46431.焊接用填充金属.金属丝和金属杆 | (Aerospace series - Aluminium alloy AL-W46431 - Filler metal for welding - Wire and rod.) |
| NF L14-050-1993 | 航空航天系列.铝合金AL-P6082-T6.200mm以下或等于200mm的挤压棒材和型材A或D | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P6082 - T6. EXTRUDED BARS AND SECTIONS A OR D INFERIOR OR EQUAL TO 200 MM. (EUROPEAN STANDARD EN 2326).) |
| NF L14-051-1994 | 航空航天系列.铝合金AL-P6082-T6.挤压棒材和型材.a/D≤200mm,周边粗粒控制 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P6082-, T6. EXTRUDED BARS AND SECTIONS. A OR D INFERIOR OR EQUAL TO 200 MM WITH PERIPHERAL COARSE GRAIN CONTROL. (EUROPEAN STANDARD EN 2636).) |
| NF L14-181-1993 | 航空航天系列.铝合金AL-P7009-T74.20mm以下或等于20mm至150mm以下或等于150mm的手工锻材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7009 - T74. HAND FORGINGS 20 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 150 MM. (EUROPEAN STANDARD EN 2093).) |
| NF L14-182-1993 | 航空航天系列.铝合金AL-P7009-T74.3mm以下或等于3mm至150mm以下或等于150mm的模锻材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7009 - T74. PIECES MATRICEES 3 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 150 MM. (EUROPEAN STANDARD EN 2094).) |
| NF L14-183-1993 | 航空航天系列.铝合金AL-P7009-T7452.40mm以下或等于40mm至150mm以下或等于150mm的手工锻材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7009 - T7452. HAND FORGINGS 40 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 150 MM. (EUROPEAN STANDARD EN 2381).) |
| NF L14-184-1993 | 航空航天系列.铝合金AL-P7009-T74511.125mm以下或等于125mm的挤压棒材和型材A或D | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7009 - T74511. EXTRUDED BARS AND SECTIONS A OR D INFERIOR OR EQUAL TO 125 MM. (EUROPEAN STANDARD EN 2385).) |
| NF L14-185-1994 | 航空航天系列.铝合金AL-P7009-T74511.挤压棒材和型材.a/D≤125mm,周边粗粒控制 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7009-, T74511. EXTRUDED BARS AND SECTIONS. A OR D INFERIOR OR EQUAL TO 125 MM WITH PERIPHERAL COARSE GRAIN CONTROL. (EUROPEAN STANDARD EN 2630).) |
| NF L14-201-1994 | 航空航天系列.铝AL-P1050A.H14.0.4mm以下或等于6mm以下或等于6mm的覆层铝合金板材及带材 | (AEROSPACE SERIES. ALUMINIUM AL-P1050A. H14. SHEET AND STRIP. 0,4 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 6 MM. (EUROPEAN STANDARD EN 2072).) |
| NF L14-204-1994 | 航空航天系列.铝合金AL-P7075-.T6或T62.0.4mm以下或等于6mm以下或等于6mm的覆层铝合金板材及带材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7075-. T6 OR T62. CLAD SHEET AND STRIP. 0,4 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 6 MM. (EUROPEAN STANDARD EN 2092).) |
| NF L14-207-1993 | 航空航天系列.铝合金AL-P7075-T651.6mm以下至80mm以下或等于80mm的铝合金板 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7075 - T651. PLATES 6 MM INFERIOR TO A INFERIOR OR EQUAL TO 80 MM. (EUROPEAN STANDARD EN 2126).) |
| NF L14-208-1993 | 航空航天系列.铝合金AL-P7075-T73511.100mm以下或等于100mm的挤压棒材和型材A或D | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7075 - T73511. EXTRUDED BARS AND SECTION A OR D INFERIOR OR EQUAL TO 100 MM. (EUROPEAN STANDARD EN 2127).) |
| NF L14-209-1993 | 航空航天系列.铝合金AL-P7075-T7351.6mm以下或等于6mm至75mm以下或等于75mm的冷拉铝棒 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7075 - T7351. DRAW BARS 6 MM INFERIOR OR EQUAL TO A OR D INFERIOR OR EQUAL TO 75 MM. (EUROPEAN STANDARD EN 2128).) |
| NF L14-210-1994 | 航空航天系列.铝合金AL-P2024-T3511.挤压棒材和型材.a/D≤150mm,周边粗粒控制 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P2024-, T3511. EXTRUDED BARS AND SECTIONS. 1,2 MM INFERIOR OR EQUAL TO A OR D INFERIOR OR EQUAL TO 150 MM WITH PERIPHERAL COARSE GRAIN CONTROL. (EUROPEAN STANDARD EN 2633).) |
| NF L14-211-1994 | 航空航天系列.铝合金AL-P7075-T73511.挤压棒材和型材.a/D≤100mm,周边粗粒控制 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7075-, T73511. EXTRUDED BARS AND SECTIONS. A OR D INFERIOR OR EQUAL TO 100 MM WITH PERIPHERAL COARSE GRAIN CONTROL. (EUROPEAN STANDARD EN 2632).) |
| NF L14-215-1994 | 航空航天系列.铝合金AL-P6061-.T6或T62.0.4mm以下或等于6mm以下或等于6mm的覆层铝合金板材及带材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P6061-. T6 OR T62. SHEET AND STRIP. 0,4 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 6 MM. (EUROPEAN STANDARD EN 2694).) |
| NF L14-216-1994 | 航空航天系列.铝合金AL-P6081-.T6.0.3mm以下或等于6mm以下或等于6mm的覆层铝合金板材及带材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P6081-. T6. SHEET AND STRIP. 0,3 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 6 MM. (EUROPEAN STANDARD EN 2695).) |
| NF L14-217-1994 | 航空航天系列.铝合金AL-P7075-.T6或T62.0.4mm以下或等于6mm以下或等于6mm的覆层铝合金板材及带材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P7075-. T6 OR T62. SHEET AND STRIP. 0,4 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 6 MM. (EUROPEAN STANDARD EN 2696).) |
| NF L14-331-1994 | 航空航天系列.铝合金AL-P5086-.H111.0.3mm以下或等于6mm以下或等于6mm的覆层铝合金板材及带材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P5086-. H111. SHEET AND STRIP. 0,3 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 6 MM. (EUROPEAN STANDARD EN 2693).) |
| NF L14-401-1994 | 航空航天系列.铝合金AL-P2014A,T4或T42.薄板和带材.0.4MM≤A≤6MM | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P2014A, T4 OR T42. SHEET AND STRIP. 0,4 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 6 MM. (EUROPEAN STANDARD EN 2395).) |
| NF L14-402-1993 | 航空航天系列.铝合金AL-P2014A,T4511.200mm以上或等于200mm的挤压棒材和型材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P2014A - T4511. EXTRUDED BARS AND SECTIONS A OR D SUPERIOR OR EQUAL TO 200 MM. (EUROPEAN STANDARD EN 2100).) |
| NF L14-403-1994 | 航空航天系列.铝合金AL-P2014A,T6或T62.薄板和带材.0.4MM≤A≤6MM | (AREOSPACE SERIES. ALUMINIUM ALLOY AL-P2014A, T6 OR T62. SHEET AND STRIP. 0,4 MM INFERIOR OR EQUAL TO A INFERIOR OR EQUAL TO 6 MM. (EUROPEAN STANDARD EN 2089).) |
| NF L14-405-1993 | 航空航天系列.铝合金AL-P2014A-T6511.150mm以下或等于150mm的挤压棒材和型材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P2014A - T6511. EXTRUDED BARS AND SECTIONS A OR D INFERIOR OR EQUAL TO 150 MM. (EUROPEAN STANDARD EN 2384).) |
| NF L14-422-1993 | 航空航天系列.铝合金AL-P2024-T3511.1.2mm以下或等于1.2mm至150mm以下或等于150mm的挤压棒材和型材 | (AEROSPACE SERIES. ALUMINIUM ALLOY AL-P2024 - T3511. EXTRUDED BARS AND SECTIONS 1,2 MM INFERIOR OR EQUAL TO A OR D INFERIOR OR EQUAL TO 150 MM. (EUROPEAN STANDARD EN 2318).) |
| NF L15-113-1972 | 铝合金板.整个表面的公差 | (ALUMINIUM ALLOY SHEET. TOLERANCE ON TOTAL SURFACE THICKNESS.) |
| NF L15-115-1973 | 铝合金板 | (ALUMINIUM ALLOY SHEET.) |
| NF L15-120-2002 | 航空航天系列.铝及铝合金板.厚度≥0.25mm和厚度≤6mm.尺寸 | (Aerospace series - Sheets, in aluminium and aluminium alloys - Thickness a more than or equal to 0,25 mm and less than or equal to 6 mm - Dimensions.) |
| NF L15-125-2002 | 航空航天系列.铝合金板.厚度为6mm〈a≤160mm.尺寸 | (Aerospace series - Plates in aluminium alloys - Thickness 6 mm inferior to a inferior or equal to 160 mm - Dimensions.) |
| NF L15-152-1978 | 铝带和铝合金带 | (Strip in aluminium and aluminium alloys.) |
| NF L15-155-2001 | 航空航天系列.铝和铝合金带.厚度≤0.25mm至≤3.2mm.尺寸 | (Aerospace series - Strips in aluminium and aluminium alloys - Thickness 0,25 mm inferior or equal to a inferior or equal to 3,2 mm - Dimensions.) |
| NF L15-312-1972 | 铝合金拉制圆棒材 | (ROUND DRAWN BARS IN ALUMINIUM ALLOYS.) |
| NF L15-313-2002 | 航空航天系列.铝及铝合金拉制圆棒材.公差等级h11.直径4mm≤ D≤63mm.尺寸 | (Aerospace series - Round bars, drawn in aluminium and aluminium alloys - Tolerance class h 11 - Diameter 4 mm inferior or equal to D inferior or equal to 63 mm - Dimensions.) |
| NF L15-314-1972 | 铝合金拉制圆棒材 | (EXTRUDED ROUND BARS IN ALUMINIUM ALLOYS.) |
| NF L15-315-2002 | 航空航天系列.铝及铝合金挤制圆棒材.直径10mm≤ D ≤ 220mm.尺寸 | (Aerospaces series - Round bars, extruded in aluminium and aluminium alloys - Diameter 10 mm inferior or equal to D inferior or equal to 220 mm - Dimensions.) |
| NF L15-322-1972 | 铝合金拉制六角形棒材.尺寸和公差 | (HEXAGON DRAWN BARS IN ALUMINIUM ALLOYS.) |
| NF L15-325-2002 | 航空航天系列.铝及铝合金拉制六角形棒材.公差等级h11.对边宽度 7mm≤ a ≤ 63mm.尺寸 | (Aerospace series - Hexagonal bars, drawn in aluminium and aluminium alloys - Tolerance class h 11 - Width across flats 7 mm inferior or equal to a inferior or equal to 63 mm - Dimensions.) |
| NF L15-332-1972 | 铝合金拉制方棒材 | (EXTRUDED AND DRAWN SQUARE BARS IN ALUMINIUM ALLOYS.) |
| NF L15-335-2002 | 航空航天系列.铝及铝合金拉制方形棒材.公差等级h11.直径 6mm≤ D ≤50mm.尺寸 | (Aerospace series - Square bars, drawn in aluminium and aluminium alloys - Tolerance class h 11 - Diameter 6 mm inferior or equal to D inferior or equal to 50 mm - Dimensions.) |
| NF L15-340-1972 | 铝合金拉制扁材 | (EXTRUDED FLAT BARS IN ALUMINIUM ALLOYS.) |
| NF L15-501-1968 | 铝合金拉制型材.一般公差 | (GENERAL TOLERANCES ON ALUMINIUM ALLOY EXTRUDED SECTIONS.) |
| NF L15-512-1973 | 铝合金拉制等边和不等边角材 | (EXTRUDED ANGLES,EQUAL AND UNEQUAL LEGS,IN ALUMINIUM ALLOYS.) |
| NF L15-515-2001 | 航空航天系列.铝合金挤压L型材.尺寸 | (Aerospace series - Extruted L-section, in aluminium alloys - Dimensions.) |
| NF L15-520-1973 | 铝合金拉制圆头角材 | (BEADED EXTRUSIONS IN ALUMINIUM ALLOYS.) |
| NF L15-525-2001 | 航空航天系列.铝合金串珠式挤压L型材.尺寸 | (Aerospace series - Beaded L-section extruded, in aluminium alloys - Dimensions.) |
| NF L15-530-1973 | 铝合金拉制Ｕ形型材 | (EXTRUDED CHANNELS IN ALUMINIUM ALLOYS.) |
| NF L15-535-2001 | 航空航天系列.铝合金挤压槽型断面.尺寸 | (Aerospace series - Extruded channel section in aluminium alloys - Dimensions.) |
| NF L15-540-1973 | 铝合金拉制Ｔ形型材 | (EXTRUDED TEE SECTIONS IN ALUMINIUM ALLOYS.) |
| NF L15-545-2001 | 航空航天系列.铝合金挤压T型材.尺寸 | (Aerospace series - Extruded T-section, in aluminium alloys - Dimensions.) |
| NF L15-555-2002 | 航空航天系列.铝合金挤制型材.一般公差 | (Aerospace series - Extruted section in aluminium alloys - General tolerances.) |
| NF L15-560-1973 | 铝合金冷弯Ω形型材 | (OMEGA SECTIONS IN ALUMINIUM ALLOYS.) |
| NF L15-570-1973 | 铝合金冷弯Ｚ形型材 | (ZED SECTIONS IN ALUMINIUM ALLOYS.) |
| NF L15-611-1973 | 铝合金拉制圆管.通用公差 | (DRAWN TUBES OF CIRCULAR SECTION IN ALUMINIUM ALLOYS. COMMON TOLERANCES.) |
| NF L15-612-1973 | 铝合金拉制圆管.精制管 | (DRAWN TUBES OF CIRCULAR SECTION IN ALUMINIUM ALLOYS. PRECISION TUBES.) |
| NF L15-640-1973 | 铝合金拉制方管 | (SQUARE DRAWN TUBES IN ALUMINIUM ALLOYS.) |
| NF L15-641-1973 | 铝合金拉制矩形管 | (RECTANGULAR DRAWN TUBES IN ALUMINIUM ALLOYS.) |
| NF L15-650-1997 | 航天航空系列.铝及铝合金结构用圆管.直径6MM≤D≤10MM.厚度1MM≤A≤6MM.尺寸(欧洲标准EN 2257) | (Aerospace series. Circular tubes for structures in aluminium and aluminium alloys. Diameter 6 mm inferior or equal to D inferior or equal to 100 mm. Thickness 1 mm inferior or equal to a inferior or equal to 6 mm. Dimensions.) |
| NF L15-651-1997 | 航天航空系列.流体用铝及铝合金圆管.直径3.2MM≤D≤100MM.厚度0.6MM≤A≤2.5MM.尺寸(欧洲标准EN 2258) | (Aerospace series. Circular tubes for fluids in aluminium and aluminium alloys. Diameter 3,2 mm inferior or equal to D inferior or equal to 100 mm. Thickness 0,6 mm inferior or equal to a inferior or equal to 2,5 mm. Dimensions.) |
| NF L15-660-1978 | 铝合金异形扁管 | (TORPEDO-SHAPED TUBES IN ALUMINIUM ALLOYS.) |
| NF L16-001-1991 | 航空航天系列.涂料和清漆.铝合金试样表面预加工的方法和类型 | (AEROSPACE SERIES. PAINTS AND VARNISHES. NATURE AND METHOD FOR PREPARATION OF SURFACE OF TEST SPECIMENS IN ALUMINIUM ALLOYS.) |
| NF L16-101-1997 | 航空和航天系列.涂料和清漆的试验方法.耐铝合金线性腐蚀的检验 | (Aerospace series. Test methods for paints and varnishes. Filiform corrosion resistance test on aluminium alloys.) |
| NF L19-101-1-1992 | 航空和航天.用铝合金制的管形隔间器材.技术规范.一般要求 | (AEROSPACE SERIES. HONEYCOMB MATEIRALS WITH TUBULAR CELLS IN ALUMINIUM ALLOYS. TECHNICAL SPECIFICATION. GENERAL REQUIREMENTS.) |
| NF L19-101-2-1992 | 航空和航天.用铝合金制的管形隔间器材.技术规范.六边形管形元件的特殊要求 | (AEROSPACE SERIES. HONEYCOMB MATERIALS WITH TUBULAR CELLS IN ALUMINIUM ALLOYS. TECHNICAL SPECIFICATION. SPECIAL REQUIREMENTS FOR HEXAGONAL TUBULAR CELLS.) |
| NF L21-106-1975 | 铆钉用铝合金、钢、耐热不锈钢合金线材.尺寸 | (Wires for rivets in aluminium alloys, steel, stainless and heat resisting alloys. Dimensions.) |
| NF L21-201-1972 | 铝合金铆钉.产品标准 | (ALUMINIUM ALLOY RIVETS. PRODUCT STANDARD.) |
| NF L21-211-1980 | 铝合金制半埋头铆钉(英寸) | (MUSHROOM HEAD RIVETS IN ALUMINIUM ALLOYS. (RECH.).) |
| NF L21-212-1980 | 铝合金制平头铆钉(英寸) | (PAN HEAD RIVETS IN ALUMINIUM ALLOYS. (RECH.).) |
| NF L21-213-1980 | 铝合金制１２０°埋头铆钉(英寸) | (120 DEGREES COUNTERSUNK HEAD RIVETS IN ALUMINIUM ALLOYS. (RECH.).) |
| NF L21-214-1980 | 铝合金制１２０°半埋头铆钉(英寸) | (RAISED 120 DEGREES COUNTERSUNK HEAD RIVETS IN ALUMINIUM ALLOYS. (RECH.).) |
| NF L21-216-1980 | 铝合金制９０°埋头铆钉(英寸) | (90 DEGREES COUNTERSUNK HEAD RIVETS IN ALUMINIUM ALLOYS. (RECH.).) |
| NF L21-271-2000 | 紧固件.紧公差T-A6V钛合金杆并有2024铝合金环的凸头锁紧螺栓 | (Fasteners - Lockbolts, protruding head, with close tolerance and titanium alloy T-A6V shank and with collar in aluminium alloy 2024.) |
| NF L21-272-2000 | 紧固件.紧公差T-A6V钛合金杆并有2024铝合金环的100°埋头锁紧螺栓 | (Fasteners - Lockbolts, 100 o countersunk head, with close tolerance and titanium alloy T-A6V shank and with collar in aluminium alloy 2024.) |
| NF L21-273-2000 | 紧固件.紧公差T-A６V铝合金杆并有XC１０钢环凸头锁紧螺栓 | (Fasteners - Lockbolts, protruding head, with close tolerance and titanium alloy T-A6V shank and with collar in steel XC 10.) |
| NF L21-311-1993 | 航空航天系列.铆钉,固体.通用头,铝1050A,英寸系列(EN 2143) | (AEROSPACE SERIES. RIVETS, SOLID, UNIVERSAL HEAD, IN ALUMINIUM 1050A, INCH BASED SERIES. (EUROPEAN STANDARD EN 2143).) |
| NF L21-312-1994 | 航空系列.根据EN 2115标准中铝合金制一般头形实心铆钉 | (AEROSPACES SERIES. RIVETS, SOLID, UNIVERSAL HEAD, IN ALUMINIUM ALLOY 2117. INCH BASED SERIES. (EUROPEAN STANDARD EN 2144).) |
| NF L21-313-1994 | 航空系列.根据EN 2115标准中阳极氧化处理铝合金制一般头形实心铆钉 | (AEROSPACE SERIES. RIVETS, SOLID, UNIVERSAL HEAD, IN ALUMINIUM ALLOY 2117, ANODIZED OR CHROMATED. INCH BASED SERIES. (EUROPEAN STANDARD EN 2145).) |
| NF L21-314-1993 | 航空航天系列.铆钉,固体.通用头,铝合金2017A,英寸系列(EN 2146) | (AEROSPACE SERIES. RIVETS, SOLID, UNIVERSAL HEAD, IN ALUMINIUM ALLOY 2017A, INCH BASED SERIES. (EUROPEAN STANDARD EN 2146).) |
| NF L21-316-1993 | 航空航天系列.铆钉,固体.通用头,铝合金5056A,英寸系列(EN 2148) | (AEROSPACES SERIES. RIVETS, SOLID, UNIVERSAL HEAD, IN ALUMINIUM ALLOY 5056A, INCH BASED SERIES. (EUROPEAN STANDARD EN 2148).) |
| NF L21-317-1996 | 航空系列.根据EN 2117标准中阳极氧化处理的铝合金制一般头形实心铆钉 | (Aerospace series. Rivets, solid, universal head, in aluminium alloy 5056A, anodized or chromated, inch based series.) |
| NF L21-321-1993 | 航空航天系列.铆钉,固体,100级常规扩钻头,铝1050A,英寸系列(EN 2550) | (AEROSPACE SERIES. RIVETS, SOLID, 100 DEGREES NORMAL COUNTERSUNK HEAD, IN ALUMINIUM 1050A,INCH BASED SERIES. (EUROPEAN STANDARD EN 2550).) |
| NF L21-322-1993 | 航空航天系列.铆钉,固体,100级常规有园顶的扩钻头,铝合金2117A,英寸系列(EN 2551) | (AEROSPACE SERIES. RIVETS, SOLID, 100 DEGREES NORMAL COUNTERSUNK HEAD WITH DOME, IN ALUMINIUM ALLOY 2117, INCH BASED SERIES. (EUROPEAN STANDARD EN 2551).) |
| NF L21-323-1993 | 航空系列.带圆顶的,铝合金2177,阳极或铬酸盐处理的100级额定嵌入埋头孔的头,固体,铆钉 | (AEROSPACE SERIES. RIVETS, SOLID, 100 DEGREES NORMAL COUNTERSUNK HEAD WITH DOME, IN ALUMINIUM ALLOY 2117, ANODIZED OR CHROMATED, INCH BASED SERIES. (EUROPEAN STANDARD EN 2552).) |
| NF L21-324-1993 | 航空航天系列.铆钉,固体,100级常规有园顶的扩钻头,铝合金2017A,英寸系列(EN 2553) | (AEROSPACE SERIES. RIVETS, SOLID, 100 DEGREES NORMAL COUNTERSUNK HEAD WITH DOME, IN ALUMINIUM ALLOY 2017A, INCH BASED SERIES. (EUROPEAN STANDARD EN 2553).) |
| NF L21-326-1993 | 航空航天系列.铆钉,固体,100级常规有园顶的扩钻头,铝合金5056A, 英寸系列(EN 2555) | (AEROSPACE SERIES. RIVETS, SOLID, 100 DEGREES NORMAL COUNTERSUNK HEAD WITH DOME, IN ALUMINIUM ALLOY 5056A, INCH BASED SERIES. (EUROPEAN STANDARD EN 2555).) |
| NF L21-327-1993 | 航空航天系列.铆钉,固体,100级常规有园顶的扩钻头,铝合金5056A, 阳极氧化处理和铬酸处理,英寸系列(EN 2556) | (AEROSPACE SEREIS. RIVETS, SOLID, 100 DEGREES NORMAL COUNTERSUNK HEAD WITH DOME, IN ALUMINIUM ALLOY 5056A, ANODIZED OR CHROMATED, INCH BASED SERIES. (EUROPEAN STANDARD EN 2556).) |
| NF L23-161-1996 | 航空系列.阳极氧化或铬酸钝化的铝合金平垫圈 | (Aerospace series. Washers, flat, in aluminium alloy, anodized or chromated.) |
| NF L23-165-1996 | 航空系列.铝合金制阳极化或铬酸钝化的大外径平垫圈 | (AEROSPACE SERIES. WASHERS, FLAT, LARGE DIAMETER, IN ALUMINIUM ALLOY, ANODIZED OR CHROMATED. (EUROPEAN STANDARD EN 2912).) |
| NF L25-110-1979 | 铝合金合页 | (ALUMINIUM ALLOY HINGES.) |
| NF L31-602-1990 | 航空和航天系列.铝合金圆环.自润滑油封.尺寸和负载 | (AEROSPACE SERIES. BUSHES,PLAIN ALUMINIUM ALLOY WITH SELF-LUBRICATING LINER. DIMENSIONS AND LOADS. (EUROPEAN STANDARD EN 2285).) |
| NF L31-603-1990 | 航空和航天系列.铝合金凸环.自润滑油封.尺寸和负载 | (AEROSPACE SERIES. BUSHES,FLANGED ALUMINIUM ALLOY WITH SELF-LUBRICATING LINER. DIMENSIONS AND LOADS. (EUROPEAN STANDARD EN 2286).) |
| NF L31-613-1989 | 航空和航天系列.铝合金制套管 | (AEROSPACE SERIES. COLLARS,ALUMINIUM ALLOY. (EUROPEAN STANDARD EN 2365).) |
| NF L35-111-1978 | 飞行控制和飞机结构用铝合金连杆.技术规范 | (ALUMINIUM ALLOY ROD BODY FOR FLIGHT CONTROL AND AIRCRAFT STRUCTURE.TECHNICAL SPECIFICATION.) |
| NF L35-112-1976 | 飞行控制和飞机结构用铝合金连杆 | (ALUMINIUM ALLOY ROD BODY FOR FLIGHT CONTROL AND AIRCRAFT STRUCTURE. DIMENSIONS.) |
| NF L35-120-1996 | 航空航天系列.飞行操纵系统用铝合金制杆体.技术规范(欧洲标准EN 2289) | (AEROSPACE SERIES. ROD BODIES IN ALUMINIUM ALLOY FOR FLIGHT CONTROLS. TECHNICAL SPECIFICATION. (EUROPEAN STANDARD EN 2289).) |
| NF L35-121-1998 | 航空航天系列.棒材,可调节末端配件用铝合金飞行控制.第1部分:尺寸和负载 | (AEROSPACE SERIES. ROD BODIES, FLIGHT CONTROL IN ALUMINIUM ALLOY FOR ADJUSTABLE END FITTINGS. PART 1 : DIMENSIONS AND LOADS. (EUROPEAN STANDARD EN 2290-1).) |
| NF L46-227-2002 | 航空航天系列.有橡胶垫层的铝制环形(P形)夹件.尺寸和质量 | (Aerospace series - Clamps, loop (“P“ type) in aluminium alloy with rubber cushioning - Dimensions, masses.) |
| NF L46-240-2002 | 航空航天系列.在铝合金中带橡胶垫的固定和移动式支架夹具.尺寸和重量 | (Aerospace series - Clamps, saddle fixed and sliding version in aluminium alloy with rubber cushioning - Dimensions, masses.) |
| NF L53-135-1960 | 飞行器电气设备.连接元件.铝套管接线头 | (Electrical equipment for aircraft. Connection elements. Aluminium crimp eye terminals.) |
| NF M87-228-2003 | 石油和天然气工业.铝合金钻杆 | (Petroleum and natural gas industries - Aluminium alloy drill pipes.) |
| NF M88-721-2002 | 便携可再充气的液化石油气钢瓶和铝瓶.处置 | (Transportable refillable steel and aluminium LPG cylinders - Disposal.) |
| NF M88-728-2003 | 液化石油气用(LPG)可运输可再填充焊接铝瓶.设计和结构 | (Transportable refillable welded aluminium cylinders for liquefied petroleum gas (LPG) - Design and construction.) |
| NF P15-315-1991 | 水硬性粘合料.高铝水泥 | (HYDRAULIC BINDERS. HIGH-ALUMINA MELTED CEMENT.) |
| NF P22-202-1-1993 | DTU 32-2.建筑工程.金属结构件.铝合金框架.第1部分:技术规范 | (DTU 32-2 - Building works - Metal construction - Aluminium alloys framework - Part 1 : technical specifications.) |
| NF P22-202-1/A1-2000 | DTU 32.2 建筑工程.金属构架.铝合金框架.第1部分:技术规范 | (DTU 32.2 - Building works - Metal construction - Aluminium alloys framework - Part 1 : technical specifications.) |
| NF P22-202-2-1993 | DTU 32-2. 建筑工程.私人合同.金属结构.铝合金制门窗框.第2部分:特殊条款 | (DTU 32-2. BUILDING WORKS. PRIVATE CONTRACTS. METAL CONSTRUCTION. ALUMINIUM ALLOYS FRAMEWORK. PART 2 : SPECIAL CLAUSES.) |
| NF P26-309-1958 | 五金.称作第一熔化的铝合金重力模制五金用品 | (HARDWARE. GRAVITY CAST ALUMINIUM ALLOY HARDWARE.) |
| NF P34-206-1-1993 | 建筑工程.预涂漆铝板及铝板制成的成型屋顶覆盖物.第1部分:技术规范 | (DTU 40-36. BUILDING WORKS. PROFILED ROOF COVERING MADE OF PREPAINTED ALUMINIUM SHEET OR ALUMINIUM SHEET. PART 1 : TECHNICAL SPECIFICATIONS.) |
| NF P34-206-2-1993 | 建筑工程.私人合同.预涂漆铝板或铝板制成的型屋顶覆盖物.第2部分:特别条款 | (DTU 40-36. BUILDING WORKS. PRIVATE CONTRACTS. PROFILED ROOF COVERING MADE OF PREPAINTED ALUMINIUM SHEET OR ALUMINIUM SHEET. PART 2 : SPECIAL CLAUSES.) |
| NF P34-308-2000 | 金属薄板制屋面制品.铝薄板制成的全支撑屋面制品的规范 | (Roofing products from metal sheet - Specification for fully supported roofing products of aluminium sheet.) |
| NF P34-309-1-2000 | 金属片屋顶产品.钢铝或不锈钢片的自支持产品规范.第1部分:钢 | (Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 1 : steel.) |
| NF P34-309-2-2000 | 金属片屋顶产品.钢铝或不锈钢片的自支持产品规范.第2部分:铝 | (Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 2 : aluminium.) |
| NF P34-309-3-2000 | 金属片屋顶产品.钢铝或不锈钢片的自支持产品规范.第3部分:不锈钢 | (Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 3 : stainless steel.) |
| NF P34-411-1983 | 屋顶.加筋或不加筋铝合金波形板 | (Roofing materials. Corrugated or ribbed aluminium alloy plates.) |
| NF P34-504-1983 | 屋顶.铝合金加筋板.静力和动力试验 | (ROOF COVERING. ALUMINIUM ALLOY RIBBED SHEETS. STATIC AND DYNAMIC BEND TESTS.) |
| NF P34-601-1981 | 连续预涂漆铝带和铝板.规范 | (STRIPS AND SHEETS MADE FROM CONTINUOUS PRELACQUERED ALUMINIUM. REQUIREMENTS.) |
| NF P34-602-1981 | 连续预涂漆铝带和铝板.试验技术 | (STRIP AND SHEETS MADE FROM CONTINUOUS PRELACQUERED ALUMINIUM. METHODS OF TESTS.) |
| NF P34-631-1983 | 屋顶.铝或铝合金制线状型材 | (ROOF COVERING. ALUMINIUM OR ALUMINIUM-ALLOY SHAPED LINEAR ELEMENTS.) |
| NF P97-414-2002 | 灯杆.第6部分:铝制灯杆的要求 | (Lighting columns - Part 6 : requirements for aluminium lighting columns.) |
| NF P98-110-1991 | 路面水泥层.硅-铝悬浮灰.规范 | (ROAD FOUNDATIONS. ALUMO SILICATE FLY ASHES. SPECIFICATIONS.) |
| NF P98-111-1992 | 公路的火泥层.石灰中的硅铝酸悬浮灰活性试验 | (ROAD FOUNDATIONS. TESTING OF REACTIVITY OF SILICO-ALUMINIOUS FLY ASH TO LIME.) |
| NF S90-045-1985 | 外科医疗器械.制药或配药用铝帽.验收检验 | (MEDICO-SURGICAL EQUIPMENT. ALUMINIUM CAPS FOR PHARMACEUTICAL USE. QUALITY ACCEPTANCE.) |
| NF S90-408-1981 | 外科医疗器械.外科植入物.氧化铝陶瓷制品 | (MEDICAL AND SURGICAL EQUIPMENT. IMPLANTS FOR SURGERY. CERAMIC MATERIALS BASED ON ALUMINA.) |
| NF S90-422-1989 | 外科植入物.接骨用金属板.圆锥形螺丝用的铝孔和扩孔 | (IMPLANTS FOR SURGERY. METAL BONE PLATES. HOLES AND SLOTS CORRESPONDING TO SCREWS WITH CONICAL UNDER-SURFACE.) |
| NF S93-103-2003 | 输血、输液和注射瓶用铝盖.一般要求和试验方法 | (Aluminium caps for transfusion, infusion and injection bottles - General requirements and test methods.) |
| NF S93-105-1993 | 输液瓶和注射管用铝-塑合成盖.要求及试验方法 | (Caps made of aluminium-plastics combinations for infusion bottles and injections vials. Requirements and test methods.) |
| NF S93-112-1993 | 注射容器及附件.第3部分:注射瓶铝盖 | (Injection containers for injectables and accessories. Part 3 : aluminium caps for injection vials.) |
| NF S93-112-3-2003 | 注射液容器及附件.第3部分:注射小瓶用的铝盖 | (Injection containers and accessories - Part 3 : aluminium caps for injection vials.) |
| NF S93-115-1993 | 注射容器及附件.第6部分:注射瓶用铝-塑料瓶盖 | (Injection contrainers for injectable and accessories. Part 6 : caps made of aluminium-plastics combinations for injection vials.) |
| NF S93-122-1993 | 医用输液设备.第3部分:输液用铝盖 | (INFUSION EQUIPMENT FOR MEDICAL USE. PART 3 : ALUMINIUM CAPS FOR INFUSION BOTTLES.) |
| NF S93-126-1993 | 医用输液设备.第7部分:铝-塑料合成制输液瓶盖 | (Infusion equipment for medical use. Part 7 : caps made of aluminium-plastics combinations for infusion bottles.) |
| NF T01-103-1997 | 铝工业用原材料.硬柏油脂,焦油沥青和胶粘剂.固定碳含量测定 | (RAW MATERIALS AND MATERIALS FOR THE ALUMINIUM INDUSTRY. PITCHES, TARS AND IMPREGNATION BINDERS. DETERMINATION OF THE FIXED CARBON CONTENT.) |
| NF T20-161-1984 | 工业用氟化铝.试验方法 | (Aluminium fluoride for industrial use. Methods of test.) |
| NF T20-165-1986 | 生产铝用碳质材料.电极用沥青.取样 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. PITCH FOR ELECTRODES. SAMPLING.) |
| NF T20-166-1986 | 生产铝用碳质材料.电极用沥青.水分测定.共沸蒸馏法(迪安斯塔克法) | (Carbonaceous materials for the production of aluminium. Pitch for electrodes. Determination of weter content. Azeotopic distillation (dean and stark) method.) |
| NF T20-167-1986 | 生产铝用碳质材料.电极用沥青.用环球法测定软化点 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. PITCH FOR ELECTRODES. DETERMINATION OF SOFTENING POINT BY THE RING-BALL METHOD.) |
| NF T20-168-1986 | 生产铝用碳质材料.电极用沥青.甲苯不溶物质总含量测定 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. PITCH FOR ELECTRODES. DETERMINATION OF CONTENT OF TOLUENE-INSOLUBLE MATERIAL.) |
| NF T20-169-1986 | 生产铝用碳质材料.电极用沥青.喹啉非溶物质含量测定 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. PITCH FOR ELECTRODES. DETERMINATION OF CONTENT OF QUINOLEINE-INSOLUBLE MATERIAL.) |
| NF T20-170-1986 | 生产铝用碳质材料.电极用沥青.密度测定.比重瓶法 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. PITCH FOR ELECTRODES. DETERMINATION OF DENSITY. PYKNOMETRIC METHOD.) |
| NF T20-171-1986 | 生产铝用碳质材料.电极用沥青.焦化值测定 | (Carbonaceous materials for the production of aluminium. Pitch for electrodes. Determination of coking value.) |
| NF T20-172-1986 | 生产铝用碳质材料.电极用沥青.动力粘度测定 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. PITCH FOR ELECTRODES. MEASUREMENT OF DYNAMIC VISCOSITY.) |
| NF T20-173-1986 | 生产铝用碳质材料.电极用沥青.灰分测定 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. PITCH FOR ELECTRODES. DETERMINATION OF ASH.) |
| NF T20-180-1986 | 生产铝用碳质材料.电极用焦炭.取样 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. COKES FOR ELECTRODES. SAMPLING.) |
| NF T20-181-1986 | 生产铝用碳质材料.煅烧焦炭.表观油含量测定.加热法 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. CALCINED COKE. DETERMINATION OF APPARENT OIL CONTENT. HEATING METHOD.) |
| NF T20-182-1986 | 生产铝用碳质材料.煅烧焦炭和煅烧制品.二甲苯密度测定.比重瓶法 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. CALCINED COKE AND CALCINED CARBON PRODUCTS. DETERMINATION OF THE DENSITY IN XYLENE. PYCNOMETRIC METHOD.) |
| NF T20-183-1986 | 生产铝用碳质材料.生焦炭和煅烧焦炭.灰分含量测定 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. GREEN AND CALCINED COKE. DETERMINATION OF ASH CONTENT.) |
| NF T20-184-1987 | 生产铝用碳质材料.煅烧焦炭.油含量测定.溶剂萃取法 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. CALCINED COKE. DETERMINATION OF OIL CONTENT. METHOD BY SOLVENT EXTRACTION.) |
| NF T20-200-1973 | 主要用于铝生产的氧化铝.取样 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. SAMPLING.) |
| NF T20-201-1973 | 主要用于铝生产的氧化铝.试验样品的制备和存放 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. PREPARATION AND STORAGE OF TEST SAMPLE.) |
| NF T20-202-1973 | 主要用于铝生产的氧化铝.分析用溶液 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. PREPARATION OF SOLUTION FOR ANALYSIS.) |
| NF T20-203-1973 | 主要用于铝生产的氧化铝.３００℃时质量损失的测定（一般湿度） | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF LOSS OF MASS AT 300 DEGREES C (CONVENTIONAL MOISTURE).) |
| NF T20-204-1973 | 主要用于铝生产的氧化铝.１０００℃和１２００℃时质量损失的测定 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF LOSS OF MASS AT 1000 DEGREES C AT 1200 DEGREES C.) |
| NF T20-205-1973 | 主要用于铝生产的氧化铝.铁含量的测定.１，１０－菲绕啉分光光度法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF IRON. 1.10-PHENANTHROLINE PHOTOMETRIC METHOD.) |
| NF T20-206-1973 | 主要用于铝生产的氧化铝.硅含量的测定.硅钼铬合物还原分光光度法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF SILICA. SPECTROPHOTOMETRIC METHOD AS THE REDUCED SILICOMOLYBDATE COMPLEX.) |
| NF T20-208-1973 | 主要用于铝生产的氧化铝.钠的测定.火焰分光光度法（发射） | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF SODIUM. FLAME SPECTROPHOTOMETRIC METHOD (EMISSION).) |
| NF T20-209-1973 | 主要用于铝生产的氧化铝.钒的测定.Ｎ－苯酰.Ｎ－苯分光光度法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF VANADIUM. N-BENZOYL-N-PHENYL-HYDROXYLAMINE PHOTOMETRIC METHOD.) |
| NF T20-210-1973 | 主要用于铝生产的氧化铝.钙的测定.原子吸收法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF CALCIUM. ATOMIC ABSORPTION METHOD.) |
| NF T20-211-1973 | 主要用于铝生产的氧化铝.钙的测定.荼亚甲基氧 酸分光光度法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF CALCIUM. SPECTROPHOTOMETRIC METHOD USING NAPHTALHYDROXAMIC ACID.) |
| NF T20-212-1973 | 主要用于铝生产的氧化铝.锌的测定.原子吸收法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF ZINC. ATOMIC ABSORPTION METHOD.) |
| NF T20-213-1973 | 主要用于铝生产的氧化铝.锌的测定.光度计表面测定法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF ZINC. P.A.N. PHOTOMETRIC METHOD.) |
| NF T20-214-1973 | 主要用于铝生产的氧化铝.氟的测定.氨基甲基－３茜素－Ｎ，Ｎ－二醋酸光度分析法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF FLUORINE. ALIZARIN COMPLEXONE AND LANTHANUM CHLORIDE SPECTROPHOTOMETRIC METHOD.) |
| NF T20-215-1973 | 主要用于铝生产的氧化铝.磷的测定.还原磷钼酸盐分光光度法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF PHOSPHOROUS. REDUCED PHOSPHOMOLYBDATE SPECTROPHOTOMETRIC METHOD.) |
| NF T20-216-1973 | 主要用于铝生产的氧化铝.硼的测定.姜黄分光光度法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF BORON. CIRCUMIN SPECTROPHOTOMETRIC METHOD.) |
| NF T20-218-1987 | 主要用于生产铝的氧化铝.粒度分布(60um以下)测定.使用电成形筛法 | (ALUMINIUM OXIDE PRIMARILLY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF THE FINE PARTICLE SIZE DISTRIBUTION (LESS THAN 60 MICROMETERS). METHOD USING ELECTROFORMED SIEVES.) |
| NF T20-219-1987 | 主要用于生产铝的氧化铝.用氮表面吸附法测定比表面积.单点法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF SPECIFIC SURFACE AREA BY NITROGEN ADSORPTION. SINGLE-POINT METHOD.) |
| NF T20-220-1973 | 主要用于铝生产的氧化铝.比重的测定.比重瓶法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF ABSOLUTE DENSITY. PYKNOMETER METHOD.) |
| NF T20-221-1973 | 主要用于铝生产的氧化铝.倾斜坡面角的测定 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. MEASUREMENT OF THE ANGLE OF REPOSE.) |
| NF T20-222-1973 | 主要用于铝生产的氧化铝.表观密度的测定 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. MEASUREMENT OF UNTAMPED DENISTY.) |
| NF T20-223-1973 | 主要用于铝生产的氧化铝.粒度分析.筛选法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. PARTICLE SIZE ANALYSIS. SIEVING METHOD.) |
| NF T20-224-1973 | 主要用于铝生产的氧化铝.吸收指数的测定 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION OF ALUMINIUM. DETERMINATION OF AN ADSORPTION INDEX.) |
| NF T20-225-1980 | 主要用于铝生产的氧化铝.火焰原子吸收分光光度法 | (ALUMINIUM OXIDE PRIMARILY USED FOR THE PRODUCTION FO ALUMINIUM. DETERMINATION OF MANGANESE CONTENT. FLAME ATOMIC ABSORPTION METHOD.) |
| NF T31-017-1979 | 颜料.涂料用含铝颜料 | (ALUMINIUM PIGMENTS FOR PAINTS.) |
| NF T31-113-2000 | 涂料用补充剂.规范和试验方法.第16部分:氢氧化铝 | (Extenders for paints - Specifications and methods of test - Part 16 : aluminium hydroxides.) |
| NF T31-115-2000 | 涂料用补充剂.规范和试验方法.第18部分:沉淀硅酸铝钠 | (Extenders for paints - Specifications and methods of test - Part 18 : precipitated sodium aluminium silicate.) |
| NF T34-750-1-2003 | 涂料和清漆.建筑用铝及铝合金涂层.第1部分:粉末涂覆材料制涂层 | (Paints and varnishes - Coating of aluminium and aluminium alloys for architectural purposes - Part 1 : coatings prepared from powder coating materials.) |
| NF T35-505-7-1999 | 涂料和相关制品使用前钢衬底的制备.非金属喷砂清理磨料的规范.第7部分:熔融氧化铝 | (PREPARATION OF STEEL SUBSTRATES BEFORE APPLICATION OF PAINTS AND RELATED PRODUCTS. SPECIFICATIONS FOR NON-METALLIC BLAST-CLEANING ABRASIVES. PART 7 : FUSED ALUMINIUM OXIDE. (EUROPEAN STANDARD EN ISO 11126-7).) |
| NF T45-022-1986 | 橡胶工业原料.铝的氧化物.氢氧化铝 | (RAW MATERIALS FOR THE RUBBER INDUSTRY. ALUMINIUM HYDROXIDE AL(OH)3.) |
| NF T76-145-2003 | 结构胶粘剂.用与浮动托辊试验法相结合的湿剥离试验评价铝表面处理技术的有效性 | (Structural adhesives - Evaluation of the effectiveness of surface treatment techniques for aluminium using a wet peel test in association with the floating roller method.) |
| NF T77-150-1986 | 工业硅树脂.羟基含量测定.氢化铝锂还原法 | (BASIC SILICONES FOR INDUSTRIAL USE. DETERMINATION OF HYDROXYL GROUPS. METHODS BY REDUCTION WITH LITHIUM-ALUMINIUM HYDRIDE.) |
| NF T90-138-2000 | 水质.铝的测定.原子吸收光谱测定法 | (Water quality - Determination of aluminium - Atomic absorption spectrometric methods.) |
| NF T94-100-1997 | 人类用水的处理试剂.硫酸铝(欧洲标准EN 878) | (CHEMICALS USED FOR TREATMENT OF WATER INTENDED FOR HUMAN CONSUMPTION. ALUMINIUM SULFATE. (EUROPEAN STANDARD EN 878).) |
| NF T94-103-1997 | 人类用水的处理试剂.氯化铝、碱式氯化铝和硫酸碱式氯化铝(欧洲标准EN 881) | (CHEMICALS USED FOR TREATMENT OF WATER INTENDED FOR HUMAN CONSUMPTION. ALUMINIUM CHLORIDE, ALUMINIUM CHLORIDE HYDROXIDE AND ALUMINIUM CHLORIDE HYDROXIDE SULFATE (MONOMERIC). (EUROPEAN STANDARD EN 881).) |
| NF T94-104-1997 | 饮用水处理用化学试剂.铝酸钠 | (CHEMICALS USED FOR TREATMENT OF WATER INTENDED FOR HUMAN CONSUMPTION. SODIUM ALUMINATE. (EUROPEAN STANDARD EN 882).) |
| NF T94-105-1997 | 饮用水处理用化学试剂.碱式氯化多铝和碱式氯化多铝硫酸盐 | (CHEMICALS USED FOR TREATMENT OF WATER INTENDED FOR HUMAN CONSUMPTION. POLYALUMINIUM CHLORIDE HYDROXIDE AND POLYALUMINIUM CHLORIDE HYDROXIDE SULFATE. (EUROPEAN STANDARD EN 883).) |
| NF T94-107-2002 | 生活饮用水处理用化学制剂.羟基硅酸盐氯化聚铝 | (Chemicals used for treatment of water intended for human consumption - Polyaluminium chloride hydroxide silicate.) |
| NF T94-108-2002 | 人类生活用水处理用化学品.羟基硅酸盐硫酸聚铝 | (Chemicals used for treatment of water intended for human consumption - Polyaluminium hydroxide silicate sulfate.) |
| NF T94-109-2002 | 生活饮用水处理用化学制剂.硫酸铝铁(III) | (Chemicals used for treatment of water intended for human consumption - Aluminium iron (III) sulfate.) |
| NF T94-110-2001 | 人类生活用水的处理用化学制剂.氯化铝铁(III)和氢氧氯化铝铁 | (Chemicals used for treatment of water intended for human consumption - Aluminium iron (III) chloride and Aluminium iron (III) chloride (monomeric) hydroxide (monomeric).) |
| NF T94-111-2000 | 人类饮用水处理用化学品.铝基絮凝剂.分析法 | (Chemicals used for treatment of water intended for human consumption - Aluminium-based coagulants - Analytical methods.) |
| NF T94-358-1997 | 人类用水的处理试剂.硫酸铝(欧洲标准EN 1205) | (Chemical used for treatment of water intended for human consumption. Sodium acid pyrophosphate.) |
| NF T94-431-2003 | 生活用水处理用产品.粒状活性铝氧土 | (Products used for treatment of water intended for human consumption - Granular activated alumina.) |
| P22-202-1993 | DTU 31-2.建筑工程.金属建筑.铝合金框架.第1部分:技术规范.第2部分:特别条款 | (DTU 32-2. Building works. Metal construction. Aluminium alloys framework. Part 1 : technical specifications - Part 2 : special clauses.) |
| XP P24-401-1999 | 金属窗和门.带有聚酰胺(PA)和聚胺酯(PU)裂缝的铝截面 | (Metal windows and doors - Aluminium profiles with polyamide (PA) or polyurethane (PU) thermal breaks - Technical specifications.) |
| 编号 | 中文名称 | 英文名称 |