| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| BS 2TA 28-1974 | 钛铝钒合金锻坯和线材规范(抗拉强度1100-1300MPa)(限定等圆断面20mm)(主要供加工符合英国标准A系列要求的紧 | Specification for forging stock and wire of titanium-aluminium-vanadium alloy (tensile strength 1100-1300 MPa) (limiting ruling section 20 mm) (primarily intended for the manufacture of fasteners complying with the requirements of the 'A' series of British Standards) |
| BS 3F 121-1995 | 航空航天用金属滑动紧固件规范 | Specification for metallic slide fasteners for aerospace purposes |
| BS 3HR 601-1989 | 紧固件制造用(最大直径或小截面尺寸为30mm)镍-铬-钛-铝耐热合金棒材和线材(镍基铬19.5、钛2.2、铝1.4)规范 | Specification for nickel-chromium-titanium-aluminium heat-resisting alloy bar and wire for the manufacture of fasteners (maximum diameter or minor sectional dimension 30 mm) (nickel base Cr 19.5, Ti 2.2, Al 1.4) |
| BS 6268-1982 | 安装螺纹紧固件用手持气动装配工具反作用扭矩及扭矩冲力测量方法 | Method of measurement for reaction torque and torque impulse from hand-held pneumatic assembly tools for installing threaded fasteners |
| BS 6462-1985 | 拴柱式窗扉撑条和正面固定楔入式紧固件机械性能规范 | Specification for mechanical performance of peg-type casement stays and face-fixed wedge-action fasteners |
| BS 6587-1985 | 紧固件的验收检验方法 | Method of acceptance inspection for fasteners |
| BS 7371-1-1991 | 金属紧固件涂层.一般要求和选择指南规范 | Coatings on metal fasteners - Specification for general requirements and selection guidelines |
| BS 7371-10-1994 | 金属紧固件涂层.第10部分:有机涂层规范 | Coatings on metal fasteners - Specification for organic coatings |
| BS 7371-2-1993 | 金属紧固件涂层.扭矩/夹紧力关系式规范 | Coatings on metal fasteners - Specification for torque/clamping force relationship |
| BS 7371-4-1994 | 金属紧固件涂层.第4部分:电镀镍、镍/铬和铜/镍/铬涂层规范. | Coatings on metal fasteners - Specification for electroplated nickel, nickel/chromium and copper/nickel/chromium coatings |
| BS 7371-6-1998 | 金属紧固件涂层.热浸镀锌涂层的规范 | Coatings on metal fasteners - Specification for hot dipped galvanized coatings |
| BS 7371-7-1994 | 金属紧固件涂层.采用机械法施加锌涂层规范 | Coatings on metal fasteners - Specification for mechanically applied zinc coatings |
| BS 7371-8-1998 | 金属紧固件涂层.粉末镀锌涂层规范 | Coatings on metal fasteners - Specification for sherardized coatings |
| BS 7371-9-1996 | 金属紧固件涂层.磷酸盐涂层或油涂层规范 | Coatings on metal fasteners - Specification for phosphate or phosphate and oil coatings |
| BS 7774-1994 | 螺纹紧固件.轴向负荷疲劳试验.第1部分:试验方法和结果评估 | Threaded fasteners - Axial load fatigue testing - Test methods and evaluation of results |
| BS 7776-1995 | 螺纹紧固件扭矩术语词汇 | Glossary of torque terminology for threaded fasteners |
| BS A 272-1977 | 高扭矩快速旋入凹槽的紧固件规范:沉头紧固件尺寸和测量 | Specification for Hi-torque speed drive recess: dimensions and gauging for countersunk head fasteners |
| BS A 273-1978 | 100°埋头紧固件的平齐度控制测量方法规范 | Specification for gauging practice for 100 ° countersunk head fasteners for flushness control |
| BS DD CEN/TS 15087-2006 | 屋顶用已装粘土和混凝土嵌合瓦片的抗隆起性测定.机械紧固件的试验方法 | Determination of the uplift resistance of installed clay and concrete interlocking tiles for roofing - Test method for mechanical fasteners |
| BS DD ISO/TS 17104-2006 | 螺纹紧固件的旋转刀具.液压推动工具.性能试验方法 | Rotary tool for threaded fasteners - Hydraulic impulse tools - Performance test method |
| BS EN 10269-1999 | 规定高温和/或低温性能的紧固件用钢及镍合金 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| BS EN 1075-2000 | 木结构.试验方法.由冲打孔金属板紧固件构成的接头 | Timber structures - Test methods - Joints made with punched metal plate fasteners |
| BS EN 12512-2001 | 木结构.试验方法.机械紧固件接头的周期测试 | Timber structures - Test methods - Cyclic testing of joints made with mechanical fasteners |
| BS EN 12549-1999 | 声学.紧固件驱动工具的噪声试验法规.工程法 | Acoustics - Noise test code for fastener driving tools - Engineering method |
| BS EN 13146-6-2002 | 铁路设施.轨道.紧固件系统的试验方法.严酷环境条件的影响 | Railway applications - Track - Test methods for fastening systems - Effect of severe environmental conditions |
| BS EN 13271-2002 | 木材紧固件.连接器接头的特征载荷能力和滑脱系数 | Timber fasteners - Characteristic load-carrying capacities and slip-moduli for connector joints |
| BS EN 13446-2002 | 木基板材.紧固件拔出能力的测定 | Wood-based panels - Determination of withdrawal capacity of fasteners |
| BS EN 13481-1-2002 | 铁路设备.轨道.紧固件系统的性能要求.定义 | Railway applications - Track - Performance requirements for fastening systems - Definitions |
| BS EN 13481-2-2002 | 铁路设备.轨道.紧固件系统的性能要求.混凝土轨枕的紧固系统 | Railway applications - Track - Performance requirements for fastening systems - Fastening systems for concrete sleepers |
| BS EN 13481-3-2002 | 铁路设备.轨道.紧固件系统的性能要求.木质轨枕的紧固件系统 | Railway applications - Track - Performance requirements for fastening systems - Fastening systems for wood sleepers |
| BS EN 13481-4-2002 | 铁路设备.轨道.紧固件系统的性能要求.钢轨枕的紧固件系统 | Railway applications - Track - Performance requirements for fastening systems - Part 4: Fastening systems for steel sleepers |
| BS EN 13481-5-2002 | 铁路设备.轨道.紧固件系统的性能要求.厚板轨道的紧固系统 | Railway applications - Track - Performance requirements for fastening systems - Fastening systems for slab track |
| BS EN 1382-1999 | 木结构.试验方法.木结构紧固件的拆卸能力 | Timber structures - Test methods - Withdrawal capacity of timber fasteners |
| BS EN 1383-1999 | 木结构.试验方法.木结构紧固件的抗拉穿性能 | Timber structures - Test methods - Pull-through resistance of timber fasteners |
| BS EN 14250-2005 | 木结构.装配穿孔金属板紧固件的预制结构组件的生产要求 | Timber structures - Product requirements for prefabricated structural members assembled with punched metal plate fasteners |
| BS EN 14831-2005 | 紧固件.紧固性能.扭矩/角度简化试验法 | Fasteners - Tightening performance - Torque/Angle simplified test method |
| BS EN 20225-1992 | 紧固件.螺栓、螺柱和螺母.图形符号和尺寸 | Fasteners - Bolts, screws, studs and nuts - Symbols and designations of dimensions |
| BS EN 20273-1992 | 紧固件.螺栓和螺钉自由尺寸孔 | Fasteners - Clearance holes for bolts and screws |
| BS EN 20898-2-1994 | 紧固件机械性能.第2部分:有规定检验载荷值的螺母.粗牙螺纹 | Mechanical properties of fasteners - Nuts with specified proof load values - Coarse thread |
| BS EN 20898-7-1995 | 紧固件机械性能.标称直径为1MM到10MM的螺栓和螺钉的扭转试验和最小扭矩 | Mechanical properties of fasteners - Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm |
| BS EN 26157-1-1992 | 紧固件的表面不均匀性.第1部分:一般要求的螺栓、螺钉和螺柱 | Fasteners - Surface discontinuities - Bolts, screws and studs for general requirements |
| BS EN 26157-3-1992 | 紧固件的表面不均匀性.第3部分:有特殊要求的螺栓、螺钉和螺柱 | Fasteners - Surface discontinuities - Bolts, screws and studs for special requirements |
| BS EN 26891-1991 | 木结构.机械紧固件接头.强度和变形特性测定一般原则 | Timber structures - Joints made with mechanical fasteners - General principles for the determination of strength and deformation characteristics |
| BS EN 28839-1992 | 紧固件机械性能.有色金属制螺栓、螺钉、螺柱和螺母 | Mechanical properties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals |
| BS EN 28970-1991 | 木结构.用机械紧固件连接的接头试验.木材致密度要求 | Timber structures - Testing of joints made with mechanical fasteners - Requirements for wood density |
| BS EN 383-2007 | 木结构.试验方法.测定榫型紧固件的嵌入强度和基值 | Timber structures - Test methods - Determination of embedment strength and foundation values for dowel type fasteners |
| BS EN 409-1993 | 木结构.试验方法.榫型紧固件屈服力矩的测定.钉子 | Timber structures - Test methods - Determination of the yield moment of dowel type fasteners - Nails |
| BS EN 4174-2006 | 航天航空系列.阳极电镀或铬酸盐处理铝合金2024米制系列、连接模压锁紧凹头紧固件 | Collars, swage locking, sheartype, in aluminium alloy 2024, anodized or chromated, metric series |
| BS EN 4176-2005 | 航空航天系列.紧公差TI-P64001钛合金制阳极电镀或铝质有色覆层１００°正常或沉头紧固/凹头锁紧螺栓.TI-P99 | Aerospace series - Lockbolts, 100 ° countersunk normal head or protruding head, tension-/ sheartype, close tolerance, in titanium alloy TI-P64001, anodized or with aluminium pigmented coating - Collars in titanium TI-P99002 or aluminium alloy 2024 - Metric series - Technical specification |
| BS EN 792-1-2000 | 手持非电动工具.安全性要求.无螺纹的机械紧固件用的装配动力工具 | Hand-held non-electric power tools - Safety requirements - Assembly power tools for non-threaded mechanical fasteners |
| BS EN 792-13-2000 | 手持非电动工具.安全性要求.紧固件旋拧工具 | Hand-held non-electric power tools - Safety requirements - Fastener driving tools |
| BS EN 792-6-2000 | 手持非电动工具.安全性要求.带螺纹紧固件用的装配动力工具 | Hand-held non-electric power tools - Safety requirements - Assembly power tools for threaded fasteners |
| BS EN 912-2000 | 木紧固件.木连接件规范 | Timber fasteners - Specifications for connections for timber |
| BS EN ISO 10683-2000 | 紧固件.非电解锌粉覆层 | Fasteners - Non-electrolytically applied zinc flake coatings |
| BS EN ISO 10684-2006 | 紧固件.热浸镀层 | Fasteners - Hot dip galvanized coatings |
| BS EN ISO 10964-1997 | 粘合剂.螺纹紧固件上厌氧粘接剂的抗扭强度的测定 | Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners |
| BS EN ISO 12777-1-1995 | 托盘连接件的检验方法.托盘用钉子、其它榫钉型紧固件和U形钉的抗弯曲的测定 | Methods of test for pallet joints - Determination of bending resistance of pallet nails, other dowel-type fasteners and staples |
| BS EN ISO 15330-1999 | 紧固件.检查氢脆性用预载荷试验.平行支承面法 | Fasteners - Preloading test for the detection of hydrogen embrittlement - Parallel bearing surface method |
| BS EN ISO 16047-2005 | 紧固件.扭矩/夹持力试验 | Fasteners - Torque/clamp force testing |
| BS EN ISO 16048-2003 | 耐腐蚀不锈钢紧固件的钝化 | Passivation of corrosion-resistant stainless-steel fasteners |
| BS EN ISO 16426-2002 | 紧固件.质量保证体系 | Fasteners - Quality assurance system |
| BS EN ISO 3269-2001 | 紧固件.验收检验 | Fasteners - Acceptance inspection |
| BS EN ISO 3506-1-1998 | 耐腐蚀不锈钢紧固件的机械特性.螺栓、螺钉和螺柱 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Bolts, screws and studs |
| BS EN ISO 3506-2-1998 | 耐腐蚀不锈钢紧固件的机械特性.螺母 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Nuts |
| BS EN ISO 3506-3-1998 | 耐腐蚀不锈钢紧固件的机械特性.不受拉伸应力作用的定位螺丝和同类紧固件 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Set screws and similar fasteners not under tensile stress |
| BS EN ISO 3506-4-2003 | 耐腐蚀不锈钢紧固件的机械特性.攻丝螺钉 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Tapping screws |
| BS EN ISO 4042-2000 | 紧固件.电镀覆层 | Fasteners - Electroplated coatings |
| BS EN ISO 4753-2000 | 紧固件.带ISO米制外螺纹的零件尾端 | Fasteners - Ends of parts with external ISO metric screw thread |
| BS EN ISO 4759-1-2001 | 紧固件公差.螺栓、螺钉、螺柱和螺母.产品等级A、B和C级 | Tolerances for fasteners - Bolts, screws, studs and nuts - Product grades A, B and C |
| BS EN ISO 4759-3-2000 | 紧固件公差.螺栓、螺钉和螺母用平垫圈.产品等级A和C | Tolerances for fasteners - Plain washers for bolts, screws and nuts - Product grades A and C |
| BS EN ISO 5845-1-1999 | 技术图纸.用紧固件连接的零件组配的简化表示法.一般原则 | Technical drawings - Simplified representation of the assemby of parts with fasteners - General principles |
| BS EN ISO 6157-2-2004 | 紧固件.表面缺陷.螺母 | Fasteners - Surface discontinuities - Nuts |
| BS EN ISO 898-1-1999 | 碳钢和合金钢制的紧固件的机械特性.螺栓、螺钉和螺柱 | Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws and studs |
| BS EN ISO 898-5-1999 | 碳钢及合金钢制紧固件的机械性能.无拉伸应力下的定位螺钉和类似的螺纹紧固件 | Mechanical properties of fasteners made of carbon steel and alloy steel - Set screws and similar threaded fasteners not under tensile stresses |
| BS EN ISO 898-6-1996 | 紧固件的机械特性.具有规定检验荷载值的螺母.细牙螺纹 | Mechanical properties of fasteners - Nuts with specified proof load values - Fine pitch thread |
| BS ISO 15629-2002 | 物料搬运托盘.新的和用过修理的木制平托盘紧固件质量 | Pallets for materials handling - Quality of fasteners for assembly of new and repair of used, flat, wooden pallets |
| BS ISO 8992-2005 | 紧固件.螺栓、螺钉、螺柱和螺母通用要求 | Fasteners - General requirements for bolts, screws, studs and nuts |
| BS S 159-1981 | 制造紧固件用含12%铬-镍-钼-钒耐热钢棒规范(1100-1300MPa;限定控制剖面50mm) | Specification for 12% chromium-nickel-molybdenum-vanadium heat-resisting steel bars for the manufacture of fasteners (1100-1300 MPa: limiting ruling section 50 mm) |
| BS SP 141-1970 | 肘杆式面板紧固件的设计与性能要求规范 | Specification for design and performance requirements for toggle type panel fasteners |
| BS SP 164-1978 | 转动锁紧、螺柱型面板紧固件(公制系列)的设计和性能要求规范 | Specification for design and performance requirements for turnlock, stud-type panel fasteners (metric series) |
| 编号 | 中文名称 | 英文名称 |