| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| EN 10269-1999 | 规定高温和/或低温性能的紧固件用钢及镍合金 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| EN 1059-1999 | 木材结构 用穿孔金属板紧固件的预制桁架的产品要求 | Timber structures - Product requirements for prefabricated trusses using punched metal plate fasteners |
| EN 1075-1999 | 木材结构 试验方法 用冲击金属板紧固件制造的连接件 | Timber structures - Test methods - Joints made with punched metal plate fasteners |
| EN 12240-1997 | 接触式密合紧固件 总带宽和有效带宽及封闭有效宽度的测定 | Touch and close fasteners - Determination of the overall and effective widths of tapes and the effective width of a closure |
| EN 12241-1999 | 接触式密合紧固件 清洗、烘干和干洗之前的封闭方法 | Touch and close fasteners - Method for closure prior to washing and drying or dry cleaning |
| EN 12242-1999 | 接触式密合紧固件 撕裂强度的测定 | Touch and close fasteners - Determination of peel strength |
| EN 12243-1999 | 接触式密合紧固件 清洗、烘干和干洗中尺寸变化的测定 | Touch and close fasteners - Determination of dimensional change in washing and drying and dry cleaning |
| EN 12512-2001 | 原木结构 试验方法 机械紧固件形成接头的循环试验 | Timber structures - Test methods - Cyclic testing of joints made with mechanical fasteners |
| EN 12549-1999 | 声学 紧固件驱动工具的噪声试验规则 工程法 | Acoustics - Noise test code for fastener driving tools - Engineering method |
| EN 13780-2003 | 触摸式密合紧固件 纵向剪切强度的测定 | Touch and close fasteners - Determination of longitudinal shear strength |
| EN 1382-1999 | 木材结构 试验方法 木材紧固件的撤出能力 | Timber structures - Test methods - Withdrawal capacity of timber fasteners |
| EN 1383-1999 | 木材结构 试验方法 木材紧固件的抗拉性 | Timber structures - Test methods - Pull through resistance of timber fasteners |
| EN 20225-1991 | 紧固件 螺栓、螺柱和螺母 尺寸代号和标注 | Fasteners; Bolts, screws, studs and nuts; Symbols and designation of dimensions (ISO 225:1983) |
| EN 20273-1991 | 紧固件 螺栓和螺钉用通孔 | Fasteners; Clearance holes for bolts and screws (ISO 273:1979) |
| EN 20898-2-1993 | 紧固件机械性能 第2部分：规定保证载荷值的螺母 粗牙螺纹 | Mechanical properties of fasteners; Part 2: Nuts with specified proof load values; Coarse thread (ISO 898-2:1992) |
| EN 20898-7-1995 | 紧固件机械性能 第7部分：螺栓与螺钉的扭矩试验和最小扭矩公称直径1MM—10MM | Mechanical properties of fasteners - Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10mm (ISO 898-7:1992) |
| EN 26157-1-1991 | 紧固件 表面缺陷 第1部分：螺栓、螺钉和螺柱一般要求 | Fasteners; surface discontinuities; Part 1: Bolts, srews and studs for general requirements (ISO 6157-1:1988) |
| EN 26157-3-1991 | 紧固件 表面缺陷 第3部分：螺栓、螺钉和螺柱的特殊要求 | Fasteners; surface discontinuities; part 3: bolts, srews and studs for special requirements (ISO 6157-3:1988) |
| EN 26891-1991 | 木材结构 机械紧固件接头 强度和变形特性测定的一般原则 | Timber structures - Joints made with mechanical fasteners - General principles for the determination of strength and deformation characteristics (ISO 6891:1983) |
| EN 28839-1991 | 紧固件机械性能 有色金属制造螺栓、螺钉、螺柱和螺母 | Mechanical properties of fasteners; Bolts, screws, studs and nuts made of non-ferrous metals (ISO 8839:1986) |
| EN 28970-1991 | 木材结构 机械紧固件接头的试验 对木材密度要求 | Timber structures - Testing of joints made with mechanical fasteners - Requirements for wood density (ISO 8970:1989) |
| EN 383-1993 | 木材结构 试验方法 榫型紧固件嵌入强度和基础值的测定 | Timber structures - Test methods - Determination of embedding strength and foundation values for dowel type fasteners |
| EN 409-1993 | 木材构件 试验方法 榫型紧固件屈服力矩的测定 钉入法 | Timber structures - Test methods - Determination of the yield moment of dowel type fasteners - Nails |
| EN 493-1992 | 紧固件 表面不均匀性 螺母 | Fasteners; Surface discontinuities; Nuts |
| EN 792-1-2000 | 手持式非电动工具 安全要求 第1部分：非螺纹机械紧固件用组装动力工具 | Hand-held non-electric power tools - Safety requirements - Part 1: Assembly power tools for non-threaded mechanical fasteners |
| EN 792-13-2000 | 手持式非电动工具 安全要求 第13部分：紧固件传动工具 | Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools |
| EN 792-6-2000 | 手持式非电动工具 安全要求 第6部分：螺纹紧固件用组装动力工具 | Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools for threaded fasteners |
| EN 912-1999+AC-2000 | 木材紧固件 木材连接器规范 | Timber fasteners - Specifications for connectors for timber |
| EN ISO 10683-2000 | 紧固件 非电解锌粉覆盖层 | Fasteners - Non-electrolytically applied zinc flake coatings (ISO 10683:2000) |
| EN ISO 10964-1997 | 粘合剂 螺纹紧固件上厌氧粘合剂的抗扭强度的测定 | Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993) |
| EN ISO 12777-1-1996 | 托盘连接件的试验方法 第1部分：托盘用钉子、其他榫钉型紧固件和U形钉的抗弯试验 | Methods of test for pallet joints - Part 1: Determination of bending resistance of pallet nails, other dowel-type fasteners and staples (ISO 12777-1:1994) |
| EN ISO 15330-1999 | 紧固件 检查氢脆用预载荷试验 平行支承面法 | Fasteners - Preloading test for the detection of hydrogen embrittlement - Parallel bearing surface method (ISO 15330:1999) |
| EN ISO 16048-2003 | 耐蚀不锈钢紧固件的钝化 | Passivation of corrosion-resistant stainless steel fasteners (ISO 16048:2003) |
| EN ISO 16426-2002 | 紧固件 质量保证体系 | Fasteners - Quality assurance system (ISO 16426:2002) |
| EN ISO 3269-2000 | 紧固件 验收检查 | Fasteners - Acceptance inspection (ISO 3269:2000) |
| EN ISO 3506-1-1997 | 耐腐蚀不锈钢紧固件的机械性能 第1部分：螺栓、螺钉和螺柱 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:1997) |
| EN ISO 3506-2-1997 | 耐腐蚀不锈钢紧固件的机械性能 第2部分：螺母 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 2: Nuts (ISO 3506-2:1997) |
| EN ISO 3506-3-1997 | 耐腐蚀不锈钢紧固件的机械性能 第3部分：紧定螺钉及类似的不受应力的螺纹紧固件 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:1997) |
| EN ISO 3506-4-2003 | 耐腐蚀不锈钢紧固件的机械性能 第4部分：自攻螺钉 | Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 4: Tapping screws (ISO 3506-4:2003) |
| EN ISO 4042-1999 | 紧固件 电镀层 | Fasteners - Electroplated coatings (ISO 4042:1999) |
| EN ISO 4753-1999 | 紧固件 ISO米制外螺纹零件的末端 | Fasteners - Ends of parts with external ISO metric screw thread (ISO 4753:1999) |
| EN ISO 4759-1-2000 | 紧固件公差 第1部分：螺栓、螺钉、螺柱和螺母 产品等级A、B和C级 | Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts; product grades A, B and C (ISO 4759-1:2000) |
| EN ISO 4759-3-2000 | 紧固件公差 第3部分：螺栓、螺钉和螺母用平垫圈 产品等级A和C级 | Tolerances for fasteners - Part 3: Plain washers for bolts, screws and nuts - Product grades A and C (ISO 4759-3:2000) |
| EN ISO 5845-1-1999 | 技术制图 紧固件组合的简单表示法 第1部分：一般原则 | Technical drawings - Simplified representation of the assembly of parts with fasteners - Part 1: General principles (ISO 5845-1:1995) |
| EN ISO 898-1-1999 | 碳钢和铸钢铸造的紧固件机械性能 第1部分：螺栓、螺钉和螺柱 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs (ISO 898-1:1999) |
| EN ISO 898-5-1998 | 碳钢和铸钢铸造的紧固件机械性能 第5部分：紧定螺钉及类似的不受拉应力的螺纹紧固件 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners not under tensile stresses (ISO 898-5:1998) |
| EN ISO 898-6-1995 | 紧固件机械性能 第6部分：规定保证载荷值的螺母 细牙螺纹 | Mechanical properties of fasteners - Part 6: Nuts with specified proof load values - Fine pitch thread (ISO 898-6:1994) |
| prEN 1660-1994 | 机械紧固件 六角产品 对边宽度 | Mechanical fasteners - Hexagon products - Widths across flats |
| prEN 2098-6-1981 | 航空航天系列 钛及耐热合金锻制产品的检验和试验要求 第6部分：棒材和线材紧固件的检验和试验要求 | Aerospace series; inspection and testing requirements for titanium and heat resisting alloy wrought products; part 6: inspection and testing requirements for bars and wires fasteners |
| prEN 2959-1999 | 航空航天系列 NI-PH1302 (NiCr20Co13Mo4Ti3Al)耐热合金固溶处理和冷加工 锻造紧固件用棒材3 mm≤D≤30 mm | Aerospace series - Heat resisting alloy NI-PH1302 (NiCr20Co13Mo4Ti3Al) - Solution treated and cold worked - Bar for forged fasteners 3 mm D 30 mm |
| prEN 4603-1999 | 航空航天系列 紧固件的二硫化钼涂层 技术规范 | Aerospace series - Molybdenum disulphide coatings of fasteners - Technical specification |
| prEN 792-14-1995 | 手持式非电动工具 安全要求 第14部分：非螺纹机械紧固件用组装动力工具 | Hand-held non electric power tools - Safety requirements - Part 14: Assembly power tools for non-threaded mechanical fasteners |
| 编号 | 中文名称 | 英文名称 |