| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| NF A03-720-2-2002 | 混凝土的钢筋和预应力用钢.试验方法.第2部分:焊接纤维 | (Steel for the reinforcement and prestressing of concrete - Test methods - Part 2 : welded fabric.) |
| NF A09-360-1985 | 无损检验.超声波.音频传播.模板纤维制的构件和材料的检查 | (NON DESTRUCTIVE TESTING. ACOUSTIC EMISSION. EXAMINATION OF COMPOSITE MATERIAL PARTS AND STRUCTURES. MATRIX FIBERS.) |
| NF B20-001-1988 | 矿物纤维绝缘产品.词汇 | (Mineral fiber based insulating products. Vocabulary.) |
| NF B20-002-1983 | 矿物纤维绝缘产品.取样要求 | (MINERAL FIBER BASED INSULATION PRODUCTS. SAMPLING REQUIREMENTS.) |
| NF B20-101-1983 | 矿物纤维绝缘产品.矿毡、垫子和矿棉板.厚度的常规测量 | (MINERAL FIBRE BASED INSULATING PRODUCTS. MINERAL WOOLFELTS,MATTRESSES AND PANELS. CONVENTIONAL MEASURE OF THICKNESS.) |
| NF B20-104-1985 | 矿物纤维绝缘产品.矿毡、垫子和矿棉板.透气性的测定 | (MINERAL BASED INSULATING PRODUCTS. MINERAL WOOLFELTS,MATTRESSES AND PANELS. DETERMINATION OF AIR PERMEABILITY.) |
| NF B20-105-1984 | 矿物纤维绝缘垫子和矿棉板表面密度的测定方法 | (METHOD OF DETERMINING THE SURFACE MASS OF MINERAL FIBRE INSULATION MATS AND PANELS.) |
| NF B20-106-1984 | 矿物纤维绝缘产品.粘聚力测定用等速垂直牵引时产品表面的扩展试验 | (MINERAL FIBER BASED INSULATED PRODUCTS. EXTENSION TEST PERPENDICULARY TO THE SURFACES OF THE PRODUCTS AT CONSTANT VELOCITY TO DETERMINE THE COHESION.) |
| NF B20-109-1985 | 矿物纤维绝缘产品.矿毡、垫子和矿棉板.分类 | (MINERAL BASED INSULATING PRODUCTS. MINERAL WOOLFELTS,MATTRESSES AND PANELS. CLASSIFICATION.) |
| NF B38-001-1989 | 纺织玻璃纤维.词汇 | (Textile glass. Vocabulary.) |
| NF B38-101-1996 | 纺织玻璃纤维.熔化物质含量的测定 | (Textiles glass. Determination of combustible-matter content.) |
| NF B38-102-1996 | 纺织玻璃纤维.短纤维或长纤维.平均直径的测定 | (Textile glass. Staple fibres or filaments. Determination of average diameter.) |
| NF B38-106-1995 | 纺织玻璃纤维.纱线.名称 | (Textile glass. Yarns. Designation.) |
| NF B38-107-1986 | 纺织玻璃纤维.纱线.规范基础 | (Textile glass. Yarns. Basis for a specification.) |
| NF B38-109-2003 | 纺织玻璃纤维.纱线.捻度平衡指数的测定 | (Textile glass - Yarns - Determination of twist balance index.) |
| NF B38-110-2002 | 纺织玻璃纤维.纱线.断裂力和断裂伸长的测定 | (Textile glass - Yarns - Determination of breaking force and breaking elongation.) |
| NF B38-116-1-1999 | 纺织玻璃纤维.纱线.第1部分:名称与符号 | (TEXTILE GLASS. YARNS. PART 1 : DESIGNATION. (EUROPEAN STANDARD EN 12654-1).) |
| NF B38-116-2-1999 | 纺织玻璃纤维.纱线.第2部分:试验方法和总规范 | (TEXTILE GLASS. YARNS. PART 2 : METHODS OF TEST AND GENERAL SPECIFICATIONS. (EUROPEAN STANDARD EN 12654-2).) |
| NF B38-116-3-1999 | 纺织玻璃纤维.纱线.第3部分:一般用途的总要求 | (TEXTILE GLASS. YARNS. PART 3 : GENERAL REQUIREMENTS FOR GENERAL APPLICATIONS. (EUROPEAN STANDARD EN 12654-3).) |
| NF B38-151-1986 | 纺织玻璃纤维.粗纱.规范基础 | (Textile glass. Rovings. Basis for a specification.) |
| NF B38-152-1983 | 玻璃纤维.粗纱刚度的测定 | (Textile glass. Determination of stiffness of rovings.) |
| NF B38-160-1-2003 | 增强材料.玻璃纤维粗纱规范.第1部分:命名 | (Reinforcements - Specification for textile glass rovings - Part 1 : designation.) |
| NF B38-160-2-2003 | 增强材料.玻璃纤维粗纱规范.第2部分:试验方法和一般要求 | (Reinforcements - Specification for textile glass rovings - Part 2 : methods of test and general requirements.) |
| NF B38-160-3-2003 | 增强材料.玻璃纤维粗纱规范.第3部分:特殊要求 | (Reinforcements - Specification for textile glass rovings - Part 3 : specific requirements.) |
| NF B38-203-1996 | 纺织玻璃纤维.织物.用条法测定断裂张力和断裂伸长 | (Textile glass. Woven fabric. Determination of tensile breaking force and elongation at break by the strip method.) |
| NF B38-206-1980 | 纺织玻璃纤维.纺织物.用弯曲法进行一般硬度的测定.用固定角度弯曲计进行测定方法 | (TEXTILES GLASS. WOVEN FABRICS. DETERMINATION OF CONVENTIONAL FLEXURAL STIFNESS. FIXED ANGLE FLEXOMETER METHOD.) |
| NF B38-207-1996 | 纺织玻璃纤维.机织织物.厚度的测定 | (TEXTILE GLASS. WOVEN FABRICS. DETERMINATION OF THICKNESS.) |
| NF B38-301-2001 | 纺织玻璃纤维.垫子(裁截或连续的多股线制).名称与符号和基本规范 | (Textile glass - Mats (made from chopped or continuous strands) - Designation and basis for specifications.) |
| NF B38-302-1983 | 纺织玻璃纤维.增强塑料用的短丝玻璃纤维.粘合剂吞苯乙烯中溶解时间的测定 | (Textile glass chopped-strand mats for reinforcement of plastics. Determination of time of dissolution of the binder in styrene.) |
| NF B38-305-1996 | 纺织玻璃纤维.织毯.抗张断裂力测定 | (Textile glass. Mats. Determination of tensile breaking force.) |
| NF B38-307-1-2003 | 增强材料.纺织玻璃纤维毡片(切短玻璃丝毡片和连续长丝毡片).第1部分: 标识 | (Reinforcements - Specification for textile glass mats (chopped strand and continuous filaments mats) - Part 1 : designation.) |
| NF B38-307-2-2003 | 增强材料.纺织玻璃纤维毡片(切短玻璃丝和连续长丝毡片)规范.第2部分:试验方法和一般要求 | (Reinforcements - Specification for textile glass mats (chopped strand and continuous filament mats) - Part 2 : methods of test and general requirements.) |
| NF B38-307-3-2003 | 增强材料.纺织玻璃纤维毡片(切短玻璃丝和连续长丝毡片)规范.第3部分:特殊要求 | (Reinforcements - Specification for textile glass mats (chopped strand and continuous filament mats) - Part 3 : specific requirements.) |
| NF B38-401-1988 | 纺织玻璃纤维.变形纱线.规范的基础 | (TEXTILE GLASS. TEXTURED YARNS. BASIS FOR A SPECIFICATION.) |
| NF B38-510-1-1999 | 增强材料.纺织玻璃纤维短切原丝规范.第1部分:名称与符号 | (REINFORCEMENTS. SPECIFICATION FOR TEXTILE GLASS CHOPPED STRANDS. PART 1 : DESIGNATION. (EUROPEAN STANDARD EN 12971-1).) |
| NF B38-510-2-1999 | 增强材料.纺织玻璃纤维短切原丝规范.第2部分:试验方法与一般要求 | (REINFORCEMENTS. SPECIFICATION FOR TEXTILE GLASS CHOPPED STRANDS. PART 2 : TEST METHODS AND GENERAL REQUIREMENTS. (EUROPEAN STANDARD EN 12971-2).) |
| NF B38-510-3-1999 | 增强材料.纺织玻璃纤维短切原丝规范.第3部分:特殊要求 | (REINFORCEMENTS. SPECIFICATION FOR TEXTILE GLASS CHOPPED STRANDS. PART 3 : SPECIFIC REQUIREMENTS. (EUROPEAN STANDARD EN 12971-3).) |
| NF B40-010-1997 | 耐火制品.第1部分:陶瓷纤维制品的术语(欧洲标准EN 1094-1) | (INSULATING REFRACTORY PRODUCTS. PART 1 : TERMINOLOGY FOR CERAMIC FIBRE PRODUCTS. (EUROPEAN STANDARD EN 1094-1).) |
| NF B51-010-1942 | 木材.与纤维垂直的拉力试验 | (WOOD. TENSILE TEST PERPENDICULAR TO FIBRES.) |
| NF B51-017-1988 | 木材.纤维的纵向拉伸.无缺陷木材细木条的小试样纵向拉伸抗断裂强度的测定 | (Wood. Tensile parallel to grain. Determination of ultimate tensile stress parallel to grain using small clear specimens.) |
| NF B51-018-1988 | 木材.纤维的纵向拉伸.无缺陷木材细木条的小试样纵向拉伸弹性模量的测定 | (WOOD. TENSILE PARALLEL TO GRAIN. DETERMINATION OF MODULUS OF ELASTICITY IN TENSILE PARALLEL TO GRAIN USING SMALL CLEAR SPECIMENS.) |
| NF B51-078-1-2001 | 木基板.结构设计的特性阀门.第1部分:OSB.颗粒板和纤维板 | (Wood-based panels - Characteristic values for structural design - Part 1 : OSB, particleboards and fiberboards.) |
| NF B51-120-1987 | 纤维板.试验的一般条件 | (Wood based panels. General testing requirements.) |
| NF B51-128-1993 | 纤维板.螺钉轴向抽出阻力的测定 | (FIBREBOARDS. DETERMINATION OF RESISTANCE TO AXIAL WITHDRAWAL OF SCREWS. (EUROPEAN STANDARD EN 320).) |
| NF B51-142-1-1993 | 纤维板.表面吸水性的测定.第1部分:干处理纤维板的试验方法 | (FIBREBOARDS. DETERMINATION OF SURFACE ABSORPTION. PART 1 : TEST METHOD FOR DRY PROCESS FIBREBOARDS. (EUROPEAN STANDARD EN 382-1).) |
| NF B51-142-2-1994 | 纤维板.表面吸水性的测定.第2部分:硬质板的试验方法 | (FIBREBOARDS. DETERMINATION OF SURFACE ABSORPTION. PART 2 : TEST METHOD FOR HARDBOARDS. (EUROPEAN STANDARD EN 382-2).) |
| NF B51-190-1987 | 纤维板.取样 | (Wood based panels. Sampling.) |
| NF B51-249-1993 | 碎料板和纤维板.浸水后膨胀厚度的测定 | (PARTICLEBOARDS AND FIBREBOARDS. DETERMINATION OF SWELLING IN THICKNESS AFTER IMMERSION IN WATER. (EUROPEAN STANDARD EN 317).) |
| NF B51-250-1993 | 刨花板和纤维板.垂直于板平面的拉伸强度的测定 | (Particleboards and fibreboards. Determination of tensile strength perpendicular to the plane of the board.) |
| NF B54-050-1993 | 木质纤维板.定义、分类和符号 | (WOOD FIBREBOARDS. DEFINITION, CLASSIFICATION AND SYMBOLS. (EUROPEAN STANDARD EN 316).) |
| NF B54-051-1-1997 | 纤维板规范.第1部分:一般要求(欧洲标准EN 622-1) | (Fibreboards. Specifications. Part 1 : general requirements.) |
| NF B54-051-1-2003 | 纤维板.规范.第1部分:一般要求 | (Fibreboards - Specifications - Part 1 : general requirements.) |
| NF B54-051-2-1997 | 纤维板规范.第2部分:硬纸板要求(欧洲标准EN 622-2) | (Fibreboards. Specifications. Part 2 : requirements for hardboards.) |
| NF B54-051-3-1997 | 纤维板规范.第3部分:中形板要求(欧洲标准EN 622-3) | (Fibreboards. Specifications. Part 3 : requirements for medium boards.) |
| NF B54-051-4-1997 | 纤维板.规范.第4部分:软质板要求 | (Fibreboards. Specifications. Part 4 : requirements for softboards.) |
| NF B54-051-5-1997 | 纤维板规范.第5部分:干制板(MDF)要求(欧洲标准EN 622-5) | (Fibreboards. Specifications. Part 5 : requirements for dry process boards (MDF).) |
| NF B54-115-1997 | 定向纤维板.定义、分类和规范 | (Oriented Strand Boards (OSB). Definitions, classification and specifications.) |
| NF B55-001-1962 | 木材.包装或填充用木质纤维 | (WOOD. WOOD FIBRES FOR PACKING AND STUFFING.) |
| NF B56-011-1980 | 纤维板.试验一般条件 | (WOOD WOOL SLABS. GENERAL TESTING PROCEDURES.) |
| NF B56-012-1980 | 纤维板.板的尺寸与斜度的测定 | (WOOD WOOL SLABS. MEASUREMENTS OF DIMENSIONS AND EDGE SQUERENESS.) |
| NF B56-013-1980 | 纤维板.密度和表面密度的测定 | (WOOD WOOL SLABS. MEASUREMENT OF DENSITY AND WEIGHT PER AREA.) |
| NF B56-014-1980 | 纤维板.弯曲试验 | (WOOD WOOL SLABS. MEASUREMENT OF BENDING STRENGTH.) |
| NF B56-015-1980 | 纤维板.垂直于板面的压力试验 | (WOOD WOOL SLABS. MEASUREMENT OF TRANSVERSE COMPRESSION.) |
| NF B56-016-1980 | 纤维板.垂直于板面的拉力试验.(带垫板的试件) | (WOOD WOOL SLABS. MEASUREMENT OF TRANSVERSE TENSILE STRENGTH .) |
| NF B56-017-1980 | 纤维板.氯离子含量的测定 | (WOOD WOOL SLABS. DETERMINATION OF CHLORURE CONTENT.) |
| NF B56-030-1982 | 纤维板.聚苯乙烯合成的.定义.命名 | (POLYSTYREN COMPOSITE WOOD WOOL SLABS. DEFINITION. DESIGNATION.) |
| NF B56-031-1982 | 纤维板.聚苯乙烯合成的.规范 | (POLYSTYREN COMPOSIITE WOOD WOOL SLABS. SPECIFICATIONS.) |
| NF C26-113-5-1995 | 云母基绝缘材料规范.第3部分:单项材料规范.第5活页:用环氧树脂粘合剂粘结的待浸渍处理的玻璃纤维织物衬底云 | (Specification for insulating materials based on mica. Part 3 : specificatins for individual materials. Sheet 5 : glass-backed mica paper with an epoxy resin binder for post-impregnation (vpi).) |
| NF C26-113-6-1995 | 云母基绝缘材料规范.第3部分:单项材料规范.第6活页:用B级环氧树脂粘合剂粘结的玻璃纤维织物衬底云母纸 | (Specification for insulating materials based on mica. Part 3 : specifications for individual materials. Sheet 6 : glass-backed mica paper with a B-stage epoxy resin binder.) |
| NF C26-148-11-1998 | 电工用压敏胶粘带.第3部分:单项材料规范.第11活页:纤维素质绉纹纸和带有橡胶热固胶粘剂的聚对苯二甲酸乙酯 | (Pressure-sensitive adhesive tapes for electrical purposes. Part 3 : specifications for individual materials. Sheet 11 : combined tapes made of creped cellulosic paper and polyethylene terephthalate film with rubber thermosetting adhesive.) |
| NF C26-148-13-1996 | 电工用压敏粘带规范.第3部分:单项材料规范.第13活页:一侧涂覆热塑材料、另一侧带有橡胶制热固性胶的结合纤 | () |
| NF C26-148-4-1998 | 电气用压力敏感粘接带.第3部分:个体材料规范.第4节:带橡胶热塑粘接的,皱折的,纤维素纸 | (Pressure-sensitive adhesive tapes for electrical purposes. Part 3 : specifications for individual materials. Sheet 4 : cellulosic paper, creped, with rubber thermosetting adhesive.) |
| NF C26-148-5-1998 | 电气用压力敏感粘接带.第3部分:个体材料规范.第5节:带橡胶热塑粘接的,非皱折的,纤维素纸 | (Pressure-sensitive adhesive tapes for electrical purposes. Part 3 : specifications for individual materials. Sheet 5 : cellulosic paper, non creped, with rubber thermosetting adhesive.) |
| NF C26-148-8-1998 | 电工用压敏胶粘带.第3部分:单项材料规范.第8节:带有压敏胶粘剂的玻璃纤维 | (Pressure-sensitive adhesive tapes for electrical purposes. Part 3 : specifications for individual materials. Sheet 8 : glass fabric with pressure-sensitive adhesive.) |
| NF C26-148-9-1998 | 电工用压敏胶粘带.第3部分:单项材料规范.第9活页:带有橡胶热固胶粘剂的纤维素醋酸纺织纤维带 | (Pressure-sensitive adhesive tapes for electrical purposes. Part 3 : specifications for individual materials. Sheet 9 : cellulose acetate woven fabric tapes with rubber thermosetting adhesive.) |
| NF C26-155-1997 | 玻璃和玻璃聚酯纤维机织带的规范.第1部分:定义、分类和总要求 | (Specification for glass and glass polyester fibre woven tapes. Part 1 : definitions, classification and general requirements.) |
| NF C26-156-1997 | 玻璃和玻璃聚酯纤维机织带的规范.第2部分:试验方法 | (Specification for glass and glass polyester fibre woven tapes. Part 2 : methods of test.) |
| NF C26-157-1-1995 | 玻璃和玻璃聚酯纤维机织带的规范.第3部分:专用材料规范.第1活页:1,2,3型织带 | (Glass and glass polyester fibre woven tapes. Part 3 : specifications for individual materials. Sheet 1 : types 1, 2 and 3 tapes.) |
| NF C26-158-1-1998 | 聚酯纤维机织带规范.第1部分:定义、名称与符号和一般要求 | (Specification for polyester fibre woven tapes. Part 1 : definitions, designation and general requirements.) |
| NF C26-158-2-1998 | 聚酯纤维机织带规范.第2部分:试验的方法 | (Specification for polyester fibre woven tapes. Part 2 : methods of test.) |
| NF C26-158-3-1-1995 | 聚酯纤维机织带.第3部分:专用材料规范.第1活页:常规的或无梭织机编织带 | (Polyester fibre woven tapes. Part 3 : specifications for individual materials. Sheet 1 : tapes woven on conventional or shuttleless looms.) |
| NF C26-197-2003 | 电工用纤维素纸.第2部分：试验方法 | (Cellulosic papers for electrical purposes - Part 2 : methods of test.) |
| NF C27-135-2003 | 绝缘油.用显微镜计数法测定纤维污染 | (Insulating oil - Determination of fibre contamination by the counting method using a microscope.) |
| NF C27-228-1-1995 | 电工用非纤维素纸.第1部分:定义和一般要求 | (Non-cellulosic papers for electrical purposes. Part 1 : definitions and general requirements.) |
| NF C27-228-2-2002 | 电工用非纤维素纸.第2部分:试验方法 | (Non-cellulosic papers for electrical purposes - Part 2 : methods of test.) |
| NF C27-228-3-1-2002 | 电工用非纤维素纸.第3部分:单项材料规范.第1活页:填充玻璃砂纸 | (Non-cellulosic papers for electrical purposes - Part 3 : specifications for individual materiels - Sheet 1 : filled glass paper.) |
| NF C27-228-3-2-2002 | 电工用非纤维素纸.第3部分:单项材料规范.第2活页:混合无机-有机纸 | (Non-cellulosic papers for electrical purposes - Part 3 : specifications for individual materiels - Sheet 2 : hybrid inorganic-organic paper.) |
| NF C27-228-3-4-2002 | 电工用非纤维素纸.第3部分:单项材料规范.第4活页:含不超过50%的云母粒子的芳族纤维纸 | (Non-cellulosic papers for electrical purposes - Part 3 : specifications for individual materiels - Sheet 4 : aramid fibre paper containing not more than 50 % of mica particles.) |
| NF C27-252-1995 | 绝缘油.火焰线性传播.使用玻璃纤维的试验方法 | (Insulating liquids. Linear flame propagation. Test method using a glass-fibre tape.) |
| NF C31-004-2000 | 特种绕组线规范.第0部分:一般要求.第4节:玻璃纤维绕组树脂或清漆浸渍的裸铜线或漆包扁铜线 | (Specifications for particular types of winding wires - Part 0 : general requirements - Section 4 : glass-fibre wound resin or varnish impregnated, bare or enamelled rectangular copper wire.) |
| NF C31-004/A1-2001 | 特种绕组线规范.第0-4部分:一般要求.玻璃纤维绕组树脂或清漆浸渍裸铜线或漆包扁铜线 | (Specifications for particular types of winding wires - Part 0-4 : general requirements Glass-fibre wound resin or varnish impregnated, bare or enamelled rectangular copper wire.) |
| NF C31-005-2000 | 特种绕组线规范.第0部分:一般要求.第5节:带玻璃纤维保护层的树脂或清漆浸渍的裸的或漆包扁铜线 | (Specifications for particular types of winding wires - Part 0 : general requirements - Section 5 : glass-fibre braided resin or varnish impregnated, bare or enamelled rectangular copper wire.) |
| NF C31-681-2000 | 特种绕组线规范.第31部分:玻璃纤维绕制树脂或清漆浸渍的裸的或漆包扁铜绕组线.温度指数180 | (Specifications for particular types of winding wires - Part 31 : glass-fibre wound resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 180.) |
| NF C31-682-2000 | 特种绕组线规范.第32部分:玻璃纤维绕制树脂或清漆浸渍的裸的或漆包扁铜绕组线.温度指数155 | (Specifications for particular types of winding wires - Part 32 : glass-fibre wound resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 155.) |
| NF C31-683-1998 | 特种绕组线规范.第33部分:温度指数为200的,玻璃纤维绕制的,硅氧烷漆处理过的裸线或漆包扁铜绕组线 | (Specifications for particular types of winding wires - Part 33 : glass-fibre wound, silicone varnish-treated, bare or enamelled rectangular copper wire, temperature index 200.) |
| NF C31-683/A1-2000 | 特种绕组线规范.第33部分:玻璃纤维环绕树脂或清漆浸渍的裸的或漆包扁铜线.温度指数200 | (Specifications for particular types of winding wires - Part 33 : glass-fibre wound resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200.) |
| NF C31-689-1995 | 特种绕组线规范.第39部分:温度指数为180的玻璃纤维编织的,聚酯或聚酰胺酯漆处理过的裸线或漆包扁铜绕组线 | (Specifications for particular types of winding wires. Part 39 : glass-fibre braided, polyester or polyesterimide varnish-treated, bare or enamelled rectangular copper wire, temperature index 180.) |
| NF C31-689/A1-2000 | 特种绕组线规范.第39部分:玻璃纤维编织的树脂的或清漆浸渍的裸的或漆包扁铜线.温度指数180 | (Specifications for particular types of winding wires - Part 39 : Glass-fibre braided, resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 180.) |
| NF C31-690-1995 | 特种绕组线规范.第40部分:温度指数为200的玻璃纤维编织的,硅氧烷漆处理过的裸线或漆包扁铜绕组线 | (Specification for particular types of winding wires. Part 40 : glass-fibre braided, silicone varnish-treated, bare or enamelled rectangular copper wire, temperature index 200.) |
| NF C31-690/A1-2000 | 特种绕组线规范.第40部分:玻璃纤维编织的树脂的或清漆浸渍的裸的或漆包扁铜线.温度指数200 | (Specifications for particular types of winding wires - Part 40 : Glass-fibre braided, resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200.) |
| NF C31-699-2001 | 特种绕阻线规范.第49部分:玻璃纤维绕阻线树脂或包漆裸露圆铜线温度指数180 | (Specifications for particular types of winding wires - Part 49 : glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire temperature index 180.) |
| NF C32-060-1996 | 通讯电缆用聚烯烃纤维绝缘护套 | (Polyolefin insulation and sheath for communication cables.) |
| NF C32-130-1990 | 设备用绝缘电缆和导线.额定电压≤450/750V的无齿素非铠装改进耐火性的C1型热塑合成纤维绝缘电缆 | () |
| NF C46-607-1991 | 发送器.致动器和程序控制装置之间FIP信息交换用的总线.光导纤维上的带状物理层 | (Fip bus for exchange of information between transmitters, actuators and programmable controllers. Fiber optic physical layer.) |
| NF C86-506-1986 | 电子元件.ＣＥＮＥＬＥＣ质量保证体系.光导纤维用插脚式光电二极管.特殊规范 | (SEMICONDUCTOR DEVICES. HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS PIN-PHOTODIODES FOR FIBRE OPTIC APPLICATIONS. BLANK DETAIL SPECIFICATION. (SPECIFICATION CECC 20 006).) |
| NF C86-508-1993 | 空白详细规范.光学纤维系统及子系统用发光二极管及红外二极管.(欧洲标准 EN 120008) | (Blank detail specification. Light emitting diodes and infrared emitting diodes for fibre optic system or sub-system.) |
| NF C91-004-24-1997 | 电磁兼容性(EMC).第4部分:试验和测量技术.第4部分:防止麻纤维物发生传导故障的装置用测试方法.基本EMC的公 | (Electromagnetic compatibility (EMC). Part 4 : testing and measurement techniques. Section 24 : test methods for protective devices for HEMP conducted disturbance. Basic EMC publication.) |
| NF C93-302-41-1998 | 纤维光学互连接装置和无源连接.基本试验和测量过程.第2-4部分:试验.单模调谐无角光学纤维连接件的天线的屏 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-41 : tests. Screen testing of attenuation of single-mode tuned non-angled optical fibre connectors.) |
| NF C93-303-40-1998 | 纤维光学互连接装置和无源连接.基本试验和测量过程.第3-40:检验和测量.偏振维持(PM)纤维柔韧铜线连接件的消 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-40 : examinations and measurements. Extinction ratio of a polarization maintaining (pm) fibre pigtailed connector.) |
| NF C93-643-300-2003 | 绝缘软管.第3部分:各种型号软管规范.第300篇:无涂层的玻璃纤维编织软管 | (Flexible insulating sleeving - Part 3 : specification requirements for individual types of sleeving - Sheet 300 : glass textile fibre sleeving, braided, uncoated.) |
| NF C93-643-400-2003 | 绝缘软管.第3部分:各种型号软管的规范要求.第400至402篇:带有机硅橡胶涂层的玻璃纤维织物软管 | (Flexible insulating sleeving - Part 3 : specification requirements for individual types of sleeving - Sheets 400 to 402 : glass textile sleeving with silicone elastomer coating.) |
| NF C93-714-1975 | 电子元件.印制电路.多层印制电路板用环氧树脂浸润的玻璃纤维织物.一般规定 | (Components for electronic equipment. Printed circuits. Woven glass fabric impregnated with expoxid resin for printed boards.) |
| NF C93-749-1996 | 印制电路用基材.第2部分:规范.第1号规范:高电气质量的酚醛纤维素纸覆铜层压板 | (Base materials for printed circuits. Part 2 : specifications. Specification number 1 : phenolic cellulose paper copper-clad laminated sheet, high electrical quality.) |
| NF C93-749/A1-2001 | 印制电路的基材.第2部分:规范.1号规范.高电气性能的铜包覆片层状酚醛纤维素纸 | (Base materials for printed circuits - Part 2 : specifications - Specification n o 1 : phenolic cellulose paper copper-clad laminated sheet high electrical quality.) |
| NF C93-752-1996 | 印制电路用基材.第2部分:规范.第2号规范:高经济质量的酚醛纤维素纸覆铜层压板 | (Base materials for printed circuits. Part 2 : specifications. Specification number 2 : phenolic cellulose paper copper-clad laminated sheet, economic quality.) |
| NF C93-752/A1-2001 | 印制电路用基材.第2部分:规范.第2号规范:酚醛纤维素纸覆铜箔层压板.经济型 | (Base materials for printed circuits - Part 2 : specification - Specification n o 2 : phenolic cellulose paper copper-clad laminated sheet, economic quality.) |
| NF C93-753-1996 | 印制电路用基材.第2部分:规范.第3号规范:规定易燃性的环氧化合物纤维素纸覆铜层压板(垂直燃烧试验) | (Base materials for printed circuits. Part 2 : specifications. Specification number 3 : epoxide cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test).) |
| NF C93-753/A1-2001 | 印制电路的基材.第2部分:规范.3号规范.限定燃烧性的铜包覆片层状环氧纤维素纸 | (Base materials for printed circuits - Part 2 : specifications - Specification n o 3 : epoxyde cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test).) |
| NF C93-754-1996 | 印制电路用基材.第2部分:规范.第4号规范:普通级的环氧化合物编织的玻璃纤维覆铜层压板 | (Base materials for printed circuits. Part 2 : specifications. Specification no 4 : epoxide woven glass fabric copper-clad laminated sheet, general purpose grade.) |
| NF C93-754/A5-2000 | 印制电路用基材.第2部分:规范.第4号规范:普通等级环氧化合物编织的玻璃纤维覆铜层压板 | (Base materials for printed circuits. Part 2 : specifications. Specification no 4 : epoxide woven glass fabric copper-clad laminated sheet, general purpose grade.) |
| NF C93-755-1996 | 印制电路用基材.第2部分:规范.第5号规范:规定易燃性的环氧化合物编织玻璃纤维织物覆铜层压板(垂直燃烧试验) | (Base materials for printed circuits. Part 2 : specifications. Specification no 5 : epoxide woven glass fabric copper-clad laminated sheet of defined flammability (vertical burning test).) |
| NF C93-755/A1-2001 | 印制电路的基本材料.第2部分:规范.第5号规范.确定了可燃性的环氧化物织物玻璃纤维铜覆层片 | (Base materials for printed circuits - Part 2 : specifications - Specification no 5 : epoxide woven glass fabric copper-clad laminated sheet of defined flammability (vertical burning test).) |
| NF C93-756-1996 | 印制电路用基材.第2部分:规范.第6号规范:规定易燃性的酚醛纤维素纸覆铜层压板(水平燃烧试验) | (Base materials for printed circuits. Part 2 : specifications. Specification no 6 : phenolic cellulose paper copper-clad laminated sheet of defined flammability (horizontal burning test).) |
| NF C93-756/A1-2001 | 印制电路的基本材料.第2部分:规范.第5号规范.确定了可燃性(水平燃烧试验)酚醛纤维素铜涂覆层片 | (Base materials for printed circuits - Part 2 : specifications - Specification no 6 : phenolic cellulose paper copper-clad laminated sheet of defined flammability (horizontal burning test).) |
| NF C93-757-1996 | 印制电路用基材.第2部分:规范.第7号规范:规定易燃性的酚醛纤维素纸覆铜层压板(垂直燃烧试验) | (Base materials for printed circuits. Part 2 : specifications. Specification no 7 : phenolic cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test).) |
| NF C93-757/A1-2001 | 印制电路的基本材料.第2部分:规范.第7号规范.确定了可燃性(垂直燃烧试验)酚醛纤维素铜涂覆层片 | (Base materials for printed circuits - Part 2 : specifications - Specification no 7 : phenolic cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test).) |
| NF C93-759-1996 | 印制电路用基材.第2部分:规范.第9号规范:规定易燃性的环氧化合物纤维素纸芯、环氧化合物玻璃布表面覆铜层压 | (Base materials for printed circuits. Part 2 : specifications. Specification number 9 : epoxide cellulose paper core, epoxyde glass cloth surfaces copper-clad laminated sheet of defined flammability (vertical burning test).) |
| NF C93-759/A1-2001 | 印制电路的基本材料.第2部分:规范.第9号规范.确定了可燃性(垂直燃烧试验)环氧纤维素纸芯环氧玻璃布表面铜涂 | (Base materials for printed circuits - Part 2 : specifications - Specification no 9 : epoxide cellulose paper core, epoxyde glass cloth surfaces copper-clad laminated sheet of defined flammability (ver) |
| NF C93-760-1996 | 印制电路用基材.第2部分:规范.第10号规范:规定易燃性的环氧化合物非编织或编织玻璃纤维增强覆铜层压板(垂直 | (Base materials for printed circuits. Part 2 : specifications. Specification number 10 : epoxide non-woven/woven glass reinforced copper-clad laminated sheet of defined flammability (vertical burning test).) |
| NF C93-761-1996 | 印制电路用基材.第2部分:规范.第11号规范:多层印制电路板制作用普通级薄环氧化合物编织的玻璃纤维覆铜层压 | (Base materials for printed circuits. Part 2 : specifications. Specification no 11 : thin epoxide woven glass fabric copper-clad laminated sheet, general purpose grade, for use in the fabrication of multilayer printed boards.) |
| NF C93-761/A1-2001 | 印制电路的基本材料.第2部分:规范.第10号规范.用于多层印制板生产中使用的一般用途级别的薄环氧织物玻璃纤 | (Base materials for printed circuits - Part 2 : specifications - Specification No 11 : thin epoxide woven glass fabric copper-clad laminated sheet, general purpose grade, for use in the fabrication of) |
| NF C93-762-1996 | 印制电路用基材.第2部分:规范.第12号规范:多层印制电路板制作用规定易燃性的薄环氧化合物编织玻璃纤维织物 | (Base materials for printed circuits. Part 2 : specifications. Specification no 12 : thin epoxide woven glass fabric copper-clad laminated sheet of defined flammability, for use in the fabrication of multilayer printed boards.) |
| NF C93-764-1996 | 印制电路用基材.第2部分:规范.第14号规范:经济质量的规定易燃性的酚醛纤维素纸覆铜层压板(垂直燃烧试验) | (Base materials for printed circuits. Part 2 : specifications. Specification number 14 : phenolic cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test), economic quality.) |
| NF C93-764/A1-2001 | 印制电路用基材.第2部分:规范.第14号规范:规定易燃性的酚醛纤维素纸镀铜层压板(垂直燃烧试验) | (Base materials for printed circuits - Part 2 : specification - Specifications number 14 : phenolic cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test), economic) |
| NF C93-766-1994 | 印制电路用基材.第2部分:规范.第16号规范:规定易燃性的聚酰亚胺玻璃纤维织物覆铜层压板(垂直燃烧试验) | (Base materials for printed circuits. Part 2 : specifications. Specification number 16 : polyimide woven glass fabric copper-clad laminated sheet of defined flammability (vertical burning test).) |
| NF C93-767-1994 | 印制电路用基材.第2部分:规范.第17号规范:多层印制板制作用的规定易燃性的聚酰亚胺编织玻璃纤维织物覆铜层 | (Base materials for printed circuits. Part 2 : specifications. Specification number 17 : thin polyimide woven glass fabric copper-clad laminated sheet of defined flammability for use in the fabrication of multilayer printed board.) |
| NF C93-768-1994 | 印制电路用基材.第2部分:规范.第18号规范:规定易燃性的比斯玛勒米德(bismaleimide)/三嗪改良型环氧化合物编 | (Base materials for printed circuits. Part 2 : specifications. Specification number 18 : bismaleimide/triazine modified epoxide woven glass fabric copper-clad laminated sheet of defined flammability (vertical burning test).) |
| NF C93-769-1994 | 印制电路用基材.第2部分:规范.第19号规范:多层印制板制作用的规定易燃性的bismaleimide/三嗪改良型环氧化物 | () |
| NF C93-780-2-10-2003 | 印制板和其它互连结构用材料.第2-10部分:包被和非包被增强基材.阻燃型铜包被改良或未改良的氰酸酯溴化环氧 | () |
| NF C93-780-2-18-2002 | 印制板和其它互连结构用材料.第2-18部分:包覆或非包覆增强基材.规定了易燃性的覆铜非编织玻璃纤维增强层压 | (Materials for printed boards and other interconnecting structures - Part 2-18 : reinforced base materials, clad and unclad - Polyester non-woven fibreglass reinforced laminated sheet of defined flamma) |
| NF C93-780-2-19-2002 | 印制板和其它互连结构用材料.第2-19部分:被包和非包被增强基材料.规定燃烧性的环氧交叉帘布层线性纤维玻璃 | (Materials for printed boards and other interconnecting structures - Part 2-19 : reinforced base materials, clad and unclad - Epoxide cross-plied linear fibreglass-reinforced laminated sheets of define) |
| NF C93-780-2-4-2002 | 印制板和其它互连结构用材料.第2-4部分:包覆和非包覆增强基材.规定了易燃性的覆铜聚酯非编织/编织玻璃纤维 | (Materials for printed boards and other interconnecting structures - Part 2-4 : reinforced base materials clad and unclad - Polyester non-woven/woven fibreglass laminated sheet of defined flammability) |
| NF C93-780-2-7-2002 | 印制板和其它互连结构用材料.第2-7部分:涂覆和非涂覆增强基材.规定了易燃性的环氧编织E型玻璃纤维层压覆铜 | (Materials for printed boards and other interconnecting structures - Part 2-7 : reinforced base materials clad and unclad - Epoxide woven E-glass laminated sheet of defined flammability (vertical burni) |
| NF C93-800-1999 | 纤维光学传感器.第1部分:总规范 | (Fibre optic sensors. Part 1 : generic specification.) |
| NF C93-807-1-3-1999 | 纤维光学通信子系统基本试验程序.第1-3部分:一般通信子系统的试验程序.中心波长和谱宽的测量 | (Fibre optic communication subsystem basic test procedures. Part 1-3 : test procedures for general communication subsystems. Central wavelength and spectral width measurement.) |
| NF C93-807-2-2-1999 | 纤维光学通信子系统基本试验过程.第2-2部分:数字系统试验过程.光学眼孔图,波形和消亡比率 | (Fibre optic communication subsystem basic test procedures. Part 2-2 : test procedures for digital systems. Optical eye pattern, waveform and extinction ratio.) |
| NF C93-811-1987 | 光导纤维互联装置和无源元件.光纤和电缆连接件的分规范.CF03型 | (FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS. SECTIONAL SPECIFICATION OF CONNECTORS FOR OPTICAL FIBRES AND CABLES. TYPE CF03.) |
| NF C93-812-1987 | 光导纤维互联装置和无源元件.光纤和电缆连接件的分规范.CF04型 | (FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS. SECTIONAL SPECIFICATION OF CONNECTORS FOR OPTICAL FIBRES AND CABLES. TYPE CF04.) |
| NF C93-813-1987 | 光导纤维互联装置和无源元件.光纤和电缆连接件的分规范.CF05型 | (FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS. SECTIONAL SPECIFICATION OF CONNECTORS FOR OPTICAL FIBRES AND CABLES. TYPE CF05.) |
| NF C93-814-1989 | 电子元件.光导纤维无源元件和连接装置.光学元件过渡规范 | (FIBRE OPTICS INTERCONNECTING DEVICES AND PASSIVE COMPONENTS. SECTIONAL SPECIFICATION FOR MECHANICAL SPLICES.) |
| NF C93-829-1997 | 纤维光学扇形输出器.第1部分:总规范 | (Fibre optic fan-outs. Part 1 : generic specification.) |
| NF C93-840-1-20-2002 | 光学纤维.第1-20部分:测量方法和试验规程.纤维几何 | (Optical fibres - Part 1-20 : measurement methods and test procedures - Fibre geometry.) |
| NF C93-840-1-21-2002 | 光学纤维.第1-21部分:测量方法和试验规程.镀涂几何 | (Optical fibres - Part 1-21 : measurement methods and test procedures - Coating geometry.) |
| NF C93-840-1-22-2002 | 光学纤维.第1-22部分:测量方法和试验程序.长度测量 | (Optical fibres - Part 1-22 : measurements methods and test procedures - Length measurement.) |
| NF C93-840-1-30-2002 | 光学纤维.第1-30部分:测量方法和试验规程.纤维验证试验 | (Optical fibres - Part 1-30 : measurement methods and test procedures - Fibre proof test.) |
| NF C93-840-1-31-2002 | 光学纤维.第1-31部分:测量方法和试验程序.抗拉强度 | (Optical fibres - Part 1-31 : measurement methods and test procedures - Tensile strength.) |
| NF C93-840-1-33-2002 | 光学纤维.第1-33部分:测量方法和试验规程.应力腐蚀性 | (Optical fibres - Part 1-33 : measurement methods and test procedures - Stress corrosion susceptibility.) |
| NF C93-840-1-34-2002 | 光学纤维.第1-34部分:测量方法和试验程序.纤维卷曲度 | (Optical fibres - Part 1-34 : measurement methods and test procedures - Fibre curl.) |
| NF C93-840-1-41-2002 | 光学纤维.第1-41部分:测量方法和试验程序.带宽度 | (Optical fibres - Part 1-41 : measurement methods and test procedures - Bandwidth.) |
| NF C93-840-1-42-2002 | 光学纤维.第1-42部分:测量方法和试验程序.颜色描述 | (Optical fibres - Part 1-42 : measurement methods and test procedures - Chromatic dispersion.) |
| NF C93-840-1-43-2002 | 光学纤维.第1-43部分:测量方法和试验程序.数字孔径 | (Optical fibres - Part 1-43 : measurement methods and test procedures - Numerical aperture.) |
| NF C93-840-1-44-2002 | 光学纤维.第1-44部分:测量方法和试验程序.截止波长 | (Optical fibres - Part 1-44 : measurements methods and test procedures - Cut-off wavelength.) |
| NF C93-840-1-46-2002 | 光学纤维.第1-46部分:测量方法和试验程序.监测光透射率变化 | (Optical fibres - Part 1-46 : measurement methods and test procedures - Monitoring of changes in optical transmittance.) |
| NF C93-840-1-47-2002 | 光学纤维.第1-47部分:测量方法和试验程序.微弯曲损耗 | (Optical fibres - Part 1-47 : measurement methods and test procedures - Macrobending loss.) |
| NF C93-840-1-50-2002 | 光学纤维.第1-50部分:测量方法和试验规程.湿热(稳态) | (Optical fibres - Part 1-50 : measurement methods and test procedures - Damp heat (steady state).) |
| NF C93-840-1-51-2002 | 光学纤维.第1-51部分:测量方法和试验程序.干热 | (Optical fibres - Part 1-51 : measurement methods and test procedures - Dry heat.) |
| NF C93-840-1-52-2002 | 光学纤维.第1-52部分:测量方法和试验程序.温度变化 | (Optical fibres - Part 1-52 : measurement methods and test procedures - Change of temperature.) |
| NF C93-840-1-53-2002 | 光学纤维.第1-53部分:测量方法和试验程序.水浸湿 | (Optical fibres - Part 1-53 : measurement methods and test procedures - Water immersion.) |
| NF C93-840-1987 | 电子元件.光导纤维过渡总规范 | (ELECTRONIC COMPONENTS. GENERIC SPECIFICATION FOR OPTICAL FIBRES.) |
| NF C93-841-1989 | 光导纤维过渡规范 | (SECTIONAL SPECIFICATION FOR OPTICAL FIBRES.) |
| NF C93-850-1-1-2002 | 光学纤维电缆.第1-1部分:总规范.总则 | (Optical fibre cables - Part 1-1 : generic specification - General.) |
| NF C93-850-2-10-2003 | 光学纤维电缆.第2-10部分:室内光缆.单股光缆和双股光缆的系列规范 | (Optical fibre cables - Part 2-10 : indoor cables - Family specification for simplex and duplex cables.) |
| NF C93-850-2-20-2003 | 光学纤维电缆.第2-20部分:室内光缆.多纤配电光缆的系列规范 | (Optical fibre cables - Part 2-20 : indoor cables - Family specification for multi-fibre optical distribution cables.) |
| NF C93-850-2-2003 | 光学纤维电缆.第2部分:室内光缆.分规范 | (Optical fibre cables - Part 2 : indoor cables - Sectional specification.) |
| NF C93-850-2-30-2003 | 光学纤维电缆.第2-30部分:室内光缆.光纤带状电缆类规范 | (Optical fibre cables - Part 2-30 : indoor cables - Family specification for optical fibre ribbon cables.) |
| NF C93-859-3-2003 | 系列规范.室内用光学纤维电缆 | (Family specification - Optical fibre cables for indoor applications.) |
| NF C93-867-2-1-2002 | 光纤通信系统中使用的接头组件和互连元件.产品规范.第2-1部分:端接在IEC 60793-2的B1类单模纤维上的FC-PC型 | (Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 2-1 : type FC-PC terminated on IEC 60793-2 category B1 singlemode fibre.) |
| NF C93-867-3-1-2002 | 光纤通信系统中使用的接头组件和互连元件.产品规范.第3-1部分:端接在IEC 60793-2的A1a类和A1b类多模纤维上 | (Connector sets and Interconnect components to be used in optical fibre communication systems - Product specifications - Part 3-1 : type SG terminated on IEC 60793-2 category A1a and A1b multimode fibr) |
| NF C93-867-5-1-2003 | 光纤通信系统中使用的连接器组和互连元件.产品规范.第5-1部分:端接在IEC 60793-2的B1.1类单模纤维上的EC型 | (Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 5-1 : type EC terminated on IEC 60793-2 category B1.1 singlemode fibre.) |
| NF C93-883-10-2003 | 纤维光学有源元件及器件.包装和接口标准.第10部分:SFF MU双20针无线电收发信机 | (Fiber optic active components and devices - Package and interface standards - Part 10 : SFF MU duplex 20-pin transceivers.) |
| NF C93-883-2-2003 | 纤维光学有源元件及器件.包装和接口标准.第2部分:SFF MT-RJ 10针无线电收发信机 | (Fibre optic active components and devices - Package and interface standards - Part 2 : SFF MT-RJ 10-pin transceiver.) |
| NF C93-883-3-2003 | 纤维光学有源元件及器件.包装和接口标准.第3部分:SFF MT-RJ 20针无线电收发信机 | (Fibre optic active components and devices - Package and interface standards - Part 3 : SFF MT-RJ 20-pin transceivers.) |
| NF C93-883-4-2003 | 纤维光学有源元件及器件.包装和接口标准.第4部分:PN 1 x 9塑料光学纤维无线电收发信机 | (Fibre optic ative components and devices - Package and interface standards - Part 4 : PN 1 x 9 plastic optical fibre transceivers.) |
| NF C93-883-5-2003 | 纤维光学有源元件及器件.包装和接口标准.第5部分:SC 1纤维光学模数 | (Fibre optic active components and devices - Package and interface standards - Part 5 : SC 1 x 9 fibre optic module.) |
| NF C93-883-7-2003 | 纤维光学有源元件及器件.包装和接口标准.第7部分:SFF LC 10针无线电收发信机 | (Fibre optic active components and devices - Package and interface standards - Part 7 : SFF LC 10-pin transceivers.) |
| NF C93-883-8-2003 | 纤维光学有源元件及器件.包装和接口标准.第8部分:SFF LC 20针无线电收发信机 | (Fibre optic active components and devices - Package and interface standards - Part 8 : SFF LC 20-pin transceivers.) |
| NF C93-883-9-2003 | 纤维光学有源元件及器件.包装和接口标准.第9部分:SFF MU双10针无线电收发信机 | (Fiber optic active components and devices - Package and interface standards - Part 9 : SFF MU duplex 10-pin transceivers.) |
| NF C93-884-4-2003 | 纤维光学有源元件和器件.性能标准.第4部分:千兆比特以太网用1300nm纤维光学无线电收发信机 | (Fibre optic active components and devices - Performance standards - Part 4 : 1 300 nm fibre optic transceivers for Gigabit Ethernet application.) |
| NF C93-902-10-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-10部分:试验.抗挤压 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-10 : tests. Crush resistance.) |
| NF C93-902-11-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-11部分:试验.轴向压力 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-11 : tests. Axial compression.) |
| NF C93-902-12-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-12部分:试验.冲压 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-12 : tests. Impact.) |
| NF C93-902-13-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-13部分:试验.加速度 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-13 : tests. Acceleration.) |
| NF C93-902-15-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-15部分:试验.连接机械的扭矩强度 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-15 : tests. Torque strength of coupling mechanism.) |
| NF C93-902-16-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-16部分:试验.去皮增大 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-16 : tests. Moult growth.) |
| NF C93-902-17-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-17部分:试验.冷却 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-17 : tests. Cold.) |
| NF C93-902-18-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-17部分:试验.干热.耐高温 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-18 : tests. Dry heat. High temperature endurance.) |
| NF C93-902-20-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-20部分:试验.气候顺序 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-20 : tests. Climatic sequence.) |
| NF C93-902-21-1997 | 光学纤维互联元件和无源元件.基本试验和测量过程.第2-21部分:试验.复合温度-湿度周期试验 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-21 : tests. Composite temperature humidity cyclic test.) |
| NF C93-902-22-1997 | 纤维光学互联装置和无源元件.基本试验和测量过程.第2-22部分:试验.温度变化 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-22 : tests. Change of temperature.) |
| NF C93-902-23-1997 | 光学纤维互联元件和无源元件.基本试验和测量过程.第2-23部分:试验.纤维光学装置非压力封闭密封 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-23 : tests. Sealing for non-pressurized closures of fibre optic devices.) |
| NF C93-902-25-1998 | 纤维光学连接装置和无源元件.基本试验和测量程序.第2-25部分:试验.闭合的密封持久性(欧洲标准EN 61 300-2-2 | (Fibres optic interconnecting devices and passive components. Basic test and measurements procedures. Part 2-25 : tests. Sealing endurance for closures.) |
| NF C93-902-26-1998 | 纤维光学连接装置和无源元件.基本试验和测量程序.第2-26部分:试验.盐雾(欧洲标准EN 61 300-2-26) | (Fibres optic interconnecting devices and passive components. Basic test and measurements procedures. Part 2-26 : tests. Salt mist.) |
| NF C93-902-28-1998 | 纤维光学连接装置和无源元件.基本试验和测量程序.第2-28部分:试验.工业气体(二氧化硫)(欧洲标准EN 61 300-2 | (Fibres optic interconnecting devices and passive components. Basic test and measurements procedures. Part 2-28 : tests. Industrial atmosphere (sulphur dioxide).) |
| NF C93-902-29-1998 | 纤维光学互联装置和无源元件.基本试验和测量过程.第2-29部分:试验.低空气压 | (Fibres optic interconnecting devices and passive components. Basic test and measurements procedures. Part 2-29 : tests. Low air pressure.) |
| NF C93-902-30-1998 | 纤维光学连接装置和无源元件.基本试验和测量程序.第2-30部分:试验.阳光辐照(欧洲标准EN 61 300-2-30) | (Fibres optic interconnecting devices and passive components. Basic test and measurements procedures. Part 2-30 : tests. Solar radiation.) |
| NF C93-902-32-1998 | 纤维光学连接装置和无源元件.基本试验和测量程序.第2-32部分:试验.水蒸气渗透(欧洲标准EN 61 300-2-32) | (Fibres optic interconnecting devices and passive components. Basic test and measurements procedures. Part 2-32 : tests. Water vapour permeation.) |
| NF C93-902-33-1998 | 纤维光学互联装置和无源元件.基本试验和测量过程.第2-33部分:试验.隔板的组装和非组装 | (Fibres optic interconnecting devices and passive components. Basic test and measurements procedures. Part 2-33 : tests. Assembly and dissassembly of closures.) |
| NF C93-902-34-1998 | 纤维光学连接装置和无源元件.基本试验和测量程序.第2-34部分:耐溶剂和污染性液体试验(欧洲标准EN 61 300-2- | (Fibres optic interconnecting devices and passive components. Basic test and measurements procedures. Part 2-34 : tests. Resistance to solvents and contaminating fluids.) |
| NF C93-902-38-1998 | 光纤互连设备和无源元件.基本试验和测量程序.第2部分第38节:试验.纤维光学设备的压合密封 | (Fibres optic interconnecting devices and passive components. Basic test and measurements procedures. Part 2-38 : tests. Sealing for pressurized closures of fibre optic devices.) |
| NF C93-902-4-1997 | 光纤互联装置和无源元件.基本试验和测量过程.第2-3部分:试验.纤维/电缆滞留 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-4 : tests. Fibre/cable retention.) |
| NF C93-902-5-1997 | 纤维光学互连装置和无源元件.基本检验和测量程序.第2-5部分:检验.扭矩/绕转 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-5 : tests. Torsion/twist.) |
| NF C93-902-6-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-6部分:检验.联接装置的抗拉强度. | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-6 : tests. Tensile strength of coupling mechanism.) |
| NF C93-902-7-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-7部分:试验.弯矩 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-7 : tests. Bending moment.) |
| NF C93-902-8-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-8部分:试验.撞击 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-8 : tests. Bump.) |
| NF C93-902-9-1997 | 纤维光学连接装置和无源元件.基本检验和测量程序.第2-9部分:试验.冲击 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 2-9 : tests. Shock.) |
| NF C93-903-13-1998 | 光纤互连设备和无源元件.基本试验和测量程序.第3部分第13节:检验和测量.纤维光学开关的控制稳定性 | (Fibres optic interconnecting devices and passive components. Basic test and measurements procedures. Part 3-13 : examinations and measurements. Control stability of a fibre optic switch.) |
| NF C93-903-19-1997 | 光学纤维互联元件和无源元件.基本试验和测量过程.第3-19部分:检验和测量.单模纤维光学元件回复损失的极化依 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-19 : examinations and measurements. Polarization dependence of return loss of a single mode fibre optic component.) |
| NF C93-903-2-2000 | 光纤互联装置和无源元件.基本试验和测量步骤.第3-2部分:检验和测量.单模纤维光学装置的偏振-衰减曲线 | (Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-2 : examinations and measurements - Polarization dependence of attenuation in a single-mode) |
| NF C93-903-22-1997 | 光学纤维互联元件和无源元件.基本试验和测量过程.第3-22部分:检验和测量.金属箍压力 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-22 : examinations and measurements. Ferrule compression force.) |
| NF C93-903-23-1998 | 光纤互联装置和无源元件.基本试验和测量过程.第2-23部分:检验和测量.与金属箍有关的纤维位置(EN 61300-3-23 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-23 : examination and measurements. Fibre position relative to ferrule endface.) |
| NF C93-903-25-1997 | 光学纤维互联元件和无源元件.基本试验和测量过程.第3-25部分:检验和测量.金属箍和安装光纤的金属箍的同心性 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-25 : examinations and measurements. Concentricity of the ferrules and ferrules with fibre installed.) |
| NF C93-903-26-1997 | 光学纤维互联元件和无源元件.基本试验和测量过程.第3-26部分:光纤和金属箍轴之间角度不重合性的测量 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-26 : examinations and measurements. Measurement of the angular misalignment between fibre and ferrules axes.) |
| NF C93-903-28-2002 | 纤维光学内连接器件和无源元件.基本试验和测量程序.第3-28部分:检验和测量.瞬态损耗 | (Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-28 : examinations and measurements - Transient loss.) |
| NF C93-903-31-2003 | 纤维光学互连器件和无源元件.基本试验和测量程序.第3-34部分:检验和测量.纤维光学源的耦合功率比测量 | (Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-31 : examinations and measurements - Coupled power ratio measurement for fibre optic sources) |
| NF C93-903-34-1998 | 纤维光学互联装置和无源元件.基本试验和测量过程.第3-34部分:检验和测量.随机配对连接器的衰减 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-34 : examinations and measurements. Attenuation of random mated connectors.) |
| NF C93-903-36-2000 | 光纤互连装置和无源部件.基本试验和测量步骤.第3-36部分:检验和测量.纤维光学连接器金属箍的内外径测量方法 | (Fibre optic interconnecting devices and passives components - Basic test and measurement procedures - Part 3-36 : examinations and measurements - measurrement methods for the inside and outside diamet) |
| NF C93-903-39-1998 | 纤维光学互联装置和无源元件.基本试验和测量过程.第3-39部分:试验,检验和测量.PC-光学连接器参考插座的选择 | (Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Part 3-39 : tests. Examinations and measurements. PC optical connector reference plug selection.) |
| NF C93-909-051-3-2002 | 纤维光学内连接器件和无源元件性能标准.第051-3部分:U类用单膜光纤和插座式固定衰减器.非环境控制 | (Fibre optic interconnecting devices and passive components performance standard - Part 051-3 : single-mode fibre, plug-style fixed attenuators for category U - Uncontrolled environment.) |
| NF C93-909-052-3-2002 | 纤维光学内连接器件和无源元件性能标准.第052-3部分:U类用单膜光纤和尾式固定衰减器.非环境控制 | (Fibre optic interconnecting devices and passive components performance standard - Part 052-3 : single-mode fibre, pigtailed-style fixed attenuators for category U - Uncontrolled environment.) |
| NF C93-909-2-1-2001 | 光纤互连装置和无源部件性能标准.第2-1部分:端接于U等级单模纤维的光纤连接器.非受控环境 | (Fibre optic interconnecting devices and passive components performance standard - Part 2-1 : fibre optic connectors terminated on single-mode fibre for category U - Uncontrolled environment.) |
| NF C93-910-13-2000 | 纤维光学连接器接口.第13部分:FC-PC型连接器门类 | (Fibre optic conector interfaces - Part 13 : type FC-PC connector family.) |
| NF C93-910-4-1997 | 纤维光学连接器接口.第4部分:SC型连接器系列 | (Fibre optic connector interfaces. Part 4 : type SC connector family.) |
| NF C93-910-4/A1-2000 | 纤维光学连接器接口.第4部分:SC型连接器门类 | (Fibre optic connector interfaces - Part 4 : type SC connector family.) |
| NF C93-910-6-1998 | 纤维光学连接器接口.第6部分:MU型连接器系列 | (Fibre optic connector interfaces. Part 6 : type MU connector family.) |
| NF C93-910-8-1998 | 纤维光学连接器的接口.第6部分:MU型连接族 | (Fibre optic connector interfaces. Part 8 : type CF08 connector family.) |
| NF C93-913-2-2001 | 纤维光学互连装置和无源元件的可靠性.第2部分:基于加速老化试验的可靠性定量评价.温度、湿度和稳定状态 | (Reliability of fibre optic interconnecting devices and passive components - Part 2 : quantitative assessment of reliability based on accelerated ageing tests - Temperature and humidity, steady state.) |
| NF C93-916-1-2002 | 纤维光学空间开关.第1部分:一般规范 | (Fibre optic spatial switches - Part 1 : generic specification.) |
| NF D90-216-1-1998 | 羽毛和羽绒.羽绒纤维支持特性的试验方法.磨擦试验.(欧洲标准12132-1) | (FEATHER AND DOWN. METHODS OF TESTING THE DOWN PROOF PROPERTIES OF FABRICS. PART 1 : RUBBING TEST. (EUROPEAN STANDARD EN 12132-1).) |
| NF D90-216-2-1998 | 羽毛和羽绒.羽绒纤维不透性能的检验.第2部分:碰撞试验 | (FEATHER AND DOWN. METHODS OF TESTING THE DOWN PROOF PROPERTIES OF FABRICS. PART 2 : IMPACT TEST. (EUROPEAN STANDARD EN 12132-2).) |
| NF E64-115-1986 | 木材加工机械.液压立式包装或填料用木质纤维制造机.术语 | (WOODWORKING MACHINES. MACHINES FOR WOOD WOOL PRODUCTION HYDRAULIC. NOMENCLATURE.) |
| NF E64-116-1986 | 木材加工机械.四种功能卧式包装或填料用木质纤维制造机.术语 | (WOODWORKING MACHINES. HORIZONTAL SCHREDDING MACHINES FOR WOOD WOOL PRODUCTION QUADRUPLE EFFECT. NOMENCLATURE.) |
| NF E75-087-2003 | 涂覆磨料.硫化纤维砂轮 | (Coated abrasives - Vulcanized-fibre discs.) |
| NF F01-281-1989 | 铁路车辆.纤维加强热固塑料材料 | (RAILWAY ROLLING STOCK. FIBRE REINFORCED THERMOSETING PLASTICS.) |
| NF F13-825-1992 | 铁路车辆.空调或通风装置用合成纤维末道空气过滤网 | (RAILWAY ROLLING STOCK. FINISHER AIR FILTERS, WITH SYNTHETIC FIBRES, FOR CONDITIONING OR VENTILATING UNITS.) |
| NF F55-301-1990 | 铁路固定设备.信号装置用玻璃纤维加强聚酯制椎架板 | (RAILWAY FIXED EQUIPMENT. FRAME-BOARDS MADE OF GLASS REINFORCED POLYESTER FOR THE SIGNALLING.) |
| NF G06-001-1979 | 纺织.粘胶或铜或特定类型莫代尔纤维和棉纤维二元混纺织物的定量分析 | (Textiles. Quantitative analysis of binary mixtures of viscose or cupro or certain types of modal and cotton fibres.) |
| NF G06-009-1979 | 织物.三醋酯纤维和某些其它纤维二元混纺织物的定量分析 | (Textiles. Quantitative analysis of binary mixtures of triacetate and certain other fibres.) |
| NF G06-010-1974 | 织物.醋酸酯纤维和三醋酯纤维二元混纺织物的定量分析 | (Textiles. Quantitative analyse of binary mixtures of acetate and triacetate fibres.) |
| NF G06-017-1975 | 棉、化学纤维素和蛋白质纤维三元混纺织物的定量化学分析 | (QUANTITATIVE CHEMICAL ANALYSIS OF TERNARY MIXTURES OF COTTON,REGENERATED CELLULOSE AND PROTEIN SUBSTANCES.) |
| NF G06-018-1971 | 纺织.纤维试验.羊毛含酸量的测定方法 | (TEXTILES. TESTS FOR FIBRES. DETERMINATION OF THE QUANTITY OF ACID CONTAINED IN WOOL.) |
| NF G06-019-1971 | 纺织.纤维试验.精梳毛条中二氯甲烷提取物的测定方法 | (DETERMINATION OF THE DICHLOROMETHANE EXTRACT IN A MESCH OF COMBED WOOL.) |
| NF G06-020-1971 | 纺织.纤维试验.尿素亚硫酸氢盐中羊毛溶解度的测定方法 | (TEXTILES. TESTS FOR FIBRES. DETERMINATION OF THE SOLUBILITY OF WOOL IN UREA BISULFITE.) |
| NF G06-029-1973 | 纺织.纤维试验.羊毛中碱含量的测定 | (TEXTILES,TESTS OF FIBRES,METHOD OF DETERMINING THE QUANTITY OF ALKALI CONTAINED IN WOOL.) |
| NF G06-030-1973 | 纺织.纤维试验.羊毛的水解产物中磺基丙氨酸含量的测定（纸上电泳法和分光光度法） | (TEXTILES,TESTS OF FIBRES,METHOD OF DETERMINING THE QUANTITY OF CYSTEIC ACID CONTAINED IN HYDROLYSATES OF WOOL BY ELECTROPHORESIS ON PAPER AND SPECTROPHOTOMETRY.) |
| NF G06-031-1973 | 纺织.纤维试验.原毛的钻色取样方法 | (TEXTILES,TESTS OF FIBRES,METHOD OF SAMPLING UNTREATED WOOL BY CORE-SAMPLING.) |
| NF G06-032-1978 | 织物.纤维素和石棉纤维二元混纺织物的定量分析 | (Textiles. Quantitative analyse of binary mixtures of cellulose fibers and asbestos.) |
| NF G06-033-1977 | 织物.纤维混纺定量分析前除去非纤维物质的方法 | (Textiles. Methods for the removal of non-fibrous matter prior to quantitative analysis of fibre mixtures.) |
| NF G06-034-1979 | 织物.再生纤维素纤维和棉纤维二元混纺织物的定量化学分析 | (TEXTILES. QUANTITATIVE CHEMICAL ANALYSIS OF BINARY MIXTURES OF REGENERATED CELLULOSE FIBRES AND COTTON.) |
| NF G06-035-1979 | 织物.聚酯和某些其它纤维二元混纺织物的定量化学分析 | (Quantitative chemical analysis of binary mixtures of polyester and certain other fibres.) |
| NF G06-037-1981 | 纺织.纤维试验.纤维素.极限粘度指数和平均粘度测定聚合度的测定 | (TEXTILES. CELLULOSE. DETERMINATION OF LIMITING VISCOSITY NUMBER AND DETERMINATION OF THE AVERAGE VISCOSIMETRIC DEGREE OF POLYMERIZATION.) |
| NF G06-038-1993 | 纺织品.纤维.纱和织物化学分析方法.粘胶丝和亚麻纤维混合物定量分析 | (TEXTILES. METHODS FOR CHEMICAL ANALYSIS OF FIBRES, YARNS AND FABRICS. QUANTITATIVE ANALYSIS OF BINARY MIXTURES OF VISCOSE AND FLAX FIBRES.) |
| NF G07-004-1973 | 纺织.纤维试验.羊毛纤维直径的测定.投影显微镜法 | (TEXTILES. TESTS FOR FIBRES. DETERMINATION OF THE DIAMETER OF WOOL FIBRES. METHOD USING THE PROJECTION MICROSCOPE.) |
| NF G07-042-3-1998 | 织物.色牢度试验.丙烯酸纤维用基本染料的内部兼容 | (TEXTILES. TESTS FOR COLOUR FASTNESS. PART Z03 : INTERCOMPATIBILITY OF BASIC DYES FOR ACRYLIC FIBRES. (EUROPEAN STANDARD EN ISO 105-Z03).) |
| NF G07-059-1968 | 纺织.纤维试验.羊毛纤维平均直径用磁导计测定方法 | (TEXTILES. TESTS OF FIBRES. AIR PERMEABILITY METHOD FOR THE DETERMINATION OF MEAN DIAMETER OF WOOL FIBRES.) |
| NF G07-060-1968 | 纺织.纤维试验.在针板机上对羊毛纤维的粗细和颔毛长短进行测定的方法 | (TEXTILES. TESTS OF FIBRES. METHOD FOR DETERMINING BEARD LENGTH AND WOOL FIBRE HEIGHT ON REED APPARATUS.) |
| NF G07-062-1980 | 纺织.纤维试验.棉花，羊毛和化学纤维的物理试验用取样方法 | (TEXTILES. TESTS FOR FIBRES. METHODS OF SAMPLING FOR TESTING FOR COTTON,WOOL OR CHEMICAL FIBRES.) |
| NF G07-073-1970 | 纺织.棉纤维细度值测定方法 | (METHOD OF DETERMINATION OF THE MICRONAIRE VALUE OF COTTON FIBRES.) |
| NF G07-074-1987 | 纺织.纤维试验.亚麻纤维细度的测定.磁导法 | (TEXTILES. FIBRE TESTS. DETERMINATION OF FLAX FIBRE FINENESS. PERMEAMETRIC METHODS.) |
| NF G07-075-1971 | 纺织.纤维试验.用投影显微镜测定髓体羊毛纤维百分比的方法 | (DETERMINATION OF THE PERCENTAGE OF WOOL FIBRE MEDULLATION USING A PROJECTION MICROSCOPE.) |
| NF G07-076-1993 | 织物.纤维.羊毛缩水特性测定 | (TEXTILE. FIBRE. DETERMINATION OF COMPRESSION CHARACTERISTICS OF WASHED WOOL.) |
| NF G07-077-1995 | 纺织品.棉纤维.成熟度的空气流动法评定 | (TEXTILES. COTTON FIBRES. EVALUATION OF MATURITY BY THE AIR FLOW METHOD. (EUROPEAN STANDARD EN ISO 10306).) |
| NF G07-079-1980 | 纺织.纤维试验.用二次对比试验退捻加捻测定纤维捻度 | (TEXTILES. TESTING THREADS. DETERMINING THE TWISTING OF THREADS BY UNTWISTING. RETWISTING WITH A DOUBLE RE-TEST.) |
| NF G07-080-1972 | 扁平棉纤维束断裂韧性的测定方法 | (METHOD FOR DETERMINATION OF BREAKING TENACITY OF FLAT BUNDLES OF COTTON FIBERS.) |
| NF G07-087-1986 | 纺织.印染牢度试验.标样织物的规范:次醋酸纤维 | (TEXTILES. TESTS FOR COLOUR FASTNESS. SPECIFICATION FOR STANDARD ADJACENT FABRIC : SECONDARY ACETATE.) |
| NF G07-088-1986 | 纺织品.色牢度试验.标准织物的规范:三醋酸纤维 | (Textiles. Tests for colour fastness. Specification for standard adjacent fabric : triacetate.) |
| NF G07-090-10-1990 | 纺织.色牢度的试验.第10部分:贴衬织物规范:复型纤维(皮芯型纤维的组组合) | (TEXTILES. TESTS FOR COLOUR FATNESS. PART 10 : SPECIFICATION FOR ADJACENT FABRIC : MULTIFIBRE.) |
| NF G07-112-2-1999 | 织物.纤维破碎特性.第2部分:破碎强度和破碎膨胀测定的气压方法 | (TEXTILES. BURSTING PROPERTIES OF FABRICS. PART 2 : PNEUMATIC METHOD FOR DETERMINATION OF BURSTING STRENGTH AND BURSTING DISTENSION. (EUROPEAN STANDARD EN ISO 13938-2).) |
| NF G07-168-1994 | 纺织品.编织纤维试验.通过测量偏离角评定织物缠结 | (TEXTILE. TESTS FOR KNITTED FABRICS. EVALUATION OF SNARLING THROUGH MEASUREMENT OF THE STEP-ASIDE ANGLE.) |
| NF G07-169-1994 | 织物.编织纤维试验.测定每单位长度和单位面积的针脚数 | (TEXTILES. TESTS FOR KNITTED FABRICS. DETERMINATION OF NUMBER OF STICHES PER UNIT LENGTH AND UNIT SURFACE.) |
| NF G07-175-1997 | 纺织品.纺织纤维作易燃性试验前的家用洗涤方法 | (TEXTILES. DOMESTIC LAUNDERING PROCEDURES FOR TEXTILE FABRICS PRIOR TO FLAMMABILITY TESTING. (EUROPEAN STANDARD EN ISO 12138).) |
| NF G07-178-1-1999 | 织物.Martinadale法对纤维磨损抗性的测定.第1部分:磨损试验装置 | (TEXTILES. DETERMINATION OF THE ABRASION RESISTANCE OF FABRICS BY THE MARTINDALE METHOD. PART 1 : MARTINDALE ABRASION TESTING APPARATUS. (EUROPEAN STANDARD EN ISO 12947-1).) |
| NF G07-178-2-1999 | 织物.Martinadale法对纤维磨损抗性的测定.第2部分:破损样品的测定 | (TEXTILES. DETERMINATION OF THE ABRASION RESISTANCE OF FABRICS BY THE MARTINDALE METHOD. PART 2 : DETERMINATION OF SPECIMEN BREAKDOWN. (EUROPEAN STANDARD EN ISO 12947-2).) |
| NF G07-178-3-1999 | 织物.Martinadale法对纤维磨损抗性的测定.第3部分:重量损失的测定 | (TEXTILES. DETERMINATION OF THE ABRASION RESISTANCE OF FABRICS BY THE MARTINDALE METHOD. PART 3 : DETERMINATION OF MASS LOSS. (EUROPEAN STANDARD EN ISO 12947-3).) |
| NF G07-178-4-1999 | 织物.Martinadale法对纤维磨损抗性的测定.第4部分:表面变化的评估 | (TEXTILES. DETERMINATION OF THE ABRASION RESISTANCE OF FABRICS BY THE MARTINDALE METHOD. PART 4 : ASSESSMENT OF APPEARANCE CHANGE. (EUROPEAN STANDARD EN ISO 12947-4).) |
| NF G07-307-1987 | 纺织.纤维试验.羊毛纤维束断裂强度的测定 | (TEXTILES. FIBRE TESTS. DETERMINATION OF THE BREAKING STRENGTH OF WOOL FIBRE BUNCHES.) |
| NF G07-309-1987 | 纺织.纤维试验.棉花纤维的紧绷长度和均匀指数的测定 | (TEXTILES. FIBRE TESTS. DETERMINATION OF SPAN LENGTH AND UNIFORMITY INDEX OF COTTON FIBRES.) |
| NF G08-001-1-1987 | 纺织.纤维和纱线.发货商品质量的测定.第1部分:质量的测定和计算 | (Textiles. Fibres and yarns. Determination of commercial mass of consignments. Part 1 : mass determination and calculations.) |
| NF G08-001-2-1987 | 纺织.纤维和纱线.发货商品质量的测定.第2部分:实验室样品取法 | (Textiles. Fibres and yarns. Determination of commercial mass of consignments. Part 2 : methods for obtaining laboratory samples.) |
| NF G08-001-3-1987 | 纺织.纤维和纱线.发货商品质量的测定.第3部分:样品净化规程 | (Textiles. Fibres and yarns. Determination of commercial mass of consignments. Part 3 : specimen cleaning procedures.) |
| NF G08-011-1987 | 纺织.纤维、纱、织物，服装.批量检验用取样方法 | (Textiles. Fibres, yarns, fabrics, clothes. Methods of sampling applicable to reception control of batches.) |
| NF G35-053-1998 | 编织地毯.用磨蚀机对羊毛纤维完整性的测定 | (Textile floor coverings. Determination of wool fibre integrity using an abrasion machine.) |
| NF G36-011-1995 | 通用纤维索.聚乙烯 | (Fibre ropes for general service. Polyethylene.) |
| NF G36-028-1974 | 绳索和绳索制品.船舶系缆用天然纤维绳索和人造纤维绳索间的等效值 | (ROPES AND CORDAGE. EQUIVALENCE BETWEEN NATURAL FIBRE ROPES AND MAN-MADE FIBRE ROPES FOR USE IN THE MOORING OF VESSELS.) |
| NF G36-030-1-2000 | 织物吊环.安全性.第1部分:水平编织吊带.一般用途的人工纤维吊带 | (Textiles slings - Safety - Part 1 : flat woven webbing slings, made of man-made fibres, for general purpose use.) |
| NF G36-030-2-2000 | 织物吊环.安全性.第2部分:圆形吊带.一般用途的人工纤维吊带 | (Textile slings - Safety - Part 2 : roundslings, made of man-made fibres, for general purpose use.) |
| NF G36-034-2-2001 | 道路车辆上的负载限制组件.安全性.第2部分:由人造纤维生产的织网绳 | (Load restraint assemblies on road vehicles - Safety - Part 2 : web lashing made from man-made fibres.) |
| NF G40-021-1975 | 从纤维整理到纺纱等工序和纺织机械的有关表格 | (TABLE RELATING TO OPERATIONS AND TEXTILE MACHINERY FROM THE PREPARATION TO THE SPINNING OF FIBRES.) |
| NF G41-005-1984 | 纺织工业设备及辅助装置.纺纱器材.连续放线环、连续放线转动罐.硬质纤维纺纱机 | (TEXTILE MACHINERY AND ALLIED MACHINERY AND ACCESSORIES. SPINNING MACHINES. RING SPINNING FRAME. POT SPINNING FRAMES. OPEN-END SPINNING MACHINES.) |
| NF H13-021-2000 | 纤维板鼓型桶.带有封闭环的标称容量为15-250升的可移动头的鼓形桶 | (Fibreboard drums - Removable head (open head) drums with closing rings with a nominal capacity of 15 l to 250 l.) |
| NF J95-046-1-2001 | 小型飞行器.壳的构造和建材尺寸.第1部分:材料.玻璃纤维增强参考层压热固树脂 | (Small craft - Hull construction and scantlings - Part 1 : materials : thermosetting resins, glass-fibre reinforcement, reference laminate.) |
| NF L17-403-2002 | 航空航天系列.纤维增强塑料.未老化材料测试前整理的标准程序 | (Aerospace series - Fibre reinforced plastics - Standard procedures for conditioning prior to testing unaged materials.) |
| NF L17-409-1998 | 航空航天系列.碳素纤维增强塑料.单向分层.垂直于纤维方向的拉伸试验 | (Aerospace series. Carbon fibre reinforced plastics. Unidirectional laminates. Tensile test perpendicular to the fibre direction.) |
| NF L17-410-1996 | 航空和航天.碳素纤维增强塑料.单向塑料层压制品.纤维方向平行抗拉试验 | (Aerospace series. Carbon fibre reinforced plastics. Unidirectioneal laminates. Tensile test parallel to the fibre direction.) |
| NF L17-413-1998 | 航空航天系列.碳素纤维层压材料.纤维.树脂和空隙量的测定 | (AEROSPACE SERIES. CARBON FIBRE LAMINATES. DETERMINATION OF THE FIBRE, RESIN AND VOID CONTENTS. (EUROPEAN STANDARD EN 2564).) |
| NF L17-420-1997 | 航天航空系列.碳纤维增强保混剂.每单位面积质量的测定(欧洲标准EN 2557) | (AEROSPACE SERIES. CARBON FIBRE PREIMPREGNATES. DETERMINATION OF MASS PER UNIT AREA. (EUROPEAN STANDARD EN 2557).) |
| NF L17-421-1997 | 航天航空系列.碳纤维增强保混剂.挥发性物质含量的测定(欧洲标准EN 2558) | (Aerospace series. Carbon fibre preimpregnates. Determination of the volatile content.) |
| NF L17-422-1997 | 航天航空系列.碳纤维增强保混剂.树脂、纤维含量和每单位面积纤维质量的测定(欧洲标准EN 2559) | (AEROSPACE SERIES. CARBON FIBRE PREIMPREGNATES. DETERMINATION OF THE RESIN AND FIBRE CONTENT AND THE MASS OF FIBRE PER UNIT AREA. (EUROPEAN STANDARD EN 2559).) |
| NF L17-454-1998 | 航空航天系列.预浸渍碳素纤维.树脂流测定 | (AEROSPACE SERIES. CARBON FIBRE PREIMPREGNATES. DETERMINATION OF THE RESIN FLOW. (EUROPEAN STANDARD EN 2560).) |
| NF L17-458-1996 | 航空和航天.纤维增强塑料.试验液体影响的测定 | (Aerospace series. Fibre reinforced plastics. Determination of the action of test fluids.) |
| NF L17-459-1996 | 航空和航天.纤维增强塑料.通过浸入测定吸水量 | (Aerospace series. Fibre reinforced plastics. Determination of water absorption by immersion.) |
| NF L17-700-1991 | 航空和航天系列.用玻璃纤维和夹层混合材料加固的层压材料.试验板的制作.(欧洲标准 EN 2374) | (Aerospace series. Glass fibre reinforced mouldings and sandwich composites. Production of test panels.) |
| NF L17-701-1989 | 航空和航空系列.玻璃纤维增强塑料.试验方法表观层间剪切力的测定 | (AEROSPACE SERIES. GLASS FIBRE REINFORCED PLASTICS. TEST METHOD. DETERMINATION OF APPARENT INTERLAMINAR SHEAR STRENGTH. (EUROPEAN STANDARD EN 2377).) |
| NF L17-703-1998 | 航空航天系列.玻璃纤维增强塑料.挠性试验.三点弯曲试验 | (Aerospace series. Glass fibre reinforced plastics. Flexural test. Three point bend method.) |
| NF L17-704-1998 | 航空航天系列.玻璃纤维增强塑料.拉伸试验 | (Aerospace series. Glass fibre reinforced plastics. Tensile test.) |
| NF L17-721-1993 | 航空航天系列.纺织玻璃纤维预浸渍.测定单位面积质量的试验方法 | (AEROSPACE SERIES. TEXTILE GLASS FIBRE PREIMPREGNATES. TEST METHOD FOR THE DETERMINATION OF MASS PER UNIT AREA. (EUROPEAN STANDARD EN 2329).) |
| NF L17-722-1993 | 航空航天系列.纺织玻璃纤维预浸渍.测定挥发物含量的试验方法 | (AEROSPACE SERIES. TEXTILE GLASS FIBRE PREIMPREGNATES. TEST METHOD FOR THE DETERMINATION OF THE CONTENT OF VOLATILE MATTER. (EUROPEAN STANDARD EN 2330).) |
| NF L17-723-1993 | 航空航天系列.纺织玻璃纤维预浸渍.测定树脂和橡胶含量及单位面积纤维质量的试验方法 | (AEROSPACE SERIES. TEXTILE GLASS FIBRE PREIMPREGNATES. TEST METHOD FOR THE DETERMINATION OF THE RESIN AND FIBRE CONTENT AND MASS OF FIBRE PER UNIT AREA. (EUROPEAN STANDARD EN 2331).) |
| NF L17-724-1993 | 航空航天系列.纺织玻璃纤维预浸渍.测定树脂流的试验方法 | (AEROSPACE SERIES. TEXTILE GLASS FIBRE PREIMPREGNATES. TEST METHOD FOR THE DETERMINATION OF THE RESIN FLOW. (EUROPEAN STANDARD EN 2332).) |
| NF L17-752-1992 | 航空航天系列.R-玻璃纤维束.产品标准.以标准RC14 160 P109为基础的玻璃纤维束 | (AEROSPACE SERIES. R-GLASS ROVINGS. PRODUCT STANDARD. ROVINGS ON THE BASIS OF STRANDS RC14 160 P109.) |
| NF L17-781-1992 | 航空航天系列.纤维束.G起重性的测定 | (AEROSPACE SERIES. ROVINGS. DETERMINATION OF THE FUZZ.) |
| NF L17-916-1995 | 航空航天系列.降落伞纤维.扭编绳的试验.锥形细纱球的数目的测定 | (AEROSPACE SERIES. PARACHUTE FABRIC. TESTING OF BRAIDED ROPE. DETERMINATION OF THE NUMBER OF YARN COPS.) |
| NF L17-917-1995 | 航空航天系列.降落伞纤维.扭编绳的试验.网织品的检测 | (AREOSPACE SERIES. PARACHUTE FABRIC. TESTING OF BRAIDED ROPE. DETERMINATION OF MESHWORK.) |
| NF L17-918-1997 | 航空航天系列.降落伞纤维.扭编绳/编带和窄幅织物的试验.浸入冷水后尺寸变化的测定 | (AEROSPACE SERIES. PARACHUTE FABRIC. TESTS ON BRAIDED ROPES/BRAIDS AND NARROW FABRICS. DETERMINATION OF DIMENSIONAL VARIATIONS AFTER IMMERSION IN COLD WATER.) |
| NF L17-950-1995 | 航空工业.飞机结构纤维用合成纤维.试板的制备 | (AIRCRAFT INDUSTRY. SYNTHETIC CLOTHS FOR THE FABRIC OF AIRPLANE STRUCTURES. REALIZATION OF TEST PANELS.) |
| NF L17-951-1995 | 航空工业.飞机结构纤维用合成纤维.风化后机械特性的测定 | (Aircraft industry. Synthetic cloths for the fabric of airplane structures. Determination of the mechanical characteristics after weathering.) |
| NF L17-952-1995 | 航空工业.飞机结构纤维用合成纤维.浆纱并绞纤维粘结的剥离强度 | (Aircraft industry. Synthetic cloths for the fabric of airplane structures. Peeling strength of the bonding of taping fabric.) |
| NF L17-953-1995 | 航空工业.飞机结构纤维用合成织物.发货时测定老化前后粘着保护的拉伸纤维的抗剪切强度 | (Aircraft industry. Synthetic cloths for the fabric of airplane structures. Determination of shear sstrength by stretching cloths, in the delivery condition, stuck then protected before and after aging.) |
| NF L17-955-1995 | 飞机工业.飞机结构纤维用合成纤维.在发货条件下纤维的透气性和透湿性测量 | (Aircraft industry. Synthetic cloths for the fabric of airplane structures. Determination of the permeability-wettability of cloths in deliverry condition.) |
| NF L17-956-1995 | 航空工业.飞机结构纤维用合成纤维.在交货条件下通过纤维的拉伸试验测定在折断状态下的负荷和拉伸率及无涂层 | (Aircraft industry. Synthetic cloths for the fabric of airplane structures. Determination of the load and elongation at rupture by tensile testing of cloths in delivery condition and of free coated cloths.) |
| NF L19-031-1993 | 航空航天系列.管状单元,六角形,玻璃纤维,酚醛树脂浸渍的蜂窝状材料.产品标准 | (AEROSPACE SERIES. HONEYCOMB MATERIAL WITH TUBULAR CELLS, HEXAGONAL, FIBRE GLASS, PHENOLIC RESIN IMPREGNATED. PRODUCT STANDARD.) |
| NF L19-032-1993 | 航空航天系列.管状单元,矩形,玻璃纤维,酚醛树脂浸渍的蜂窝状材料.产品标准 | (AEROSPACE SERIES. HONEYCOMB MATERIALS WITH TUBULAR CELLS, RECTANGULAR, FIBRE GLASS, PHENOLIC RESIN IMPREGNATED. PRODUCT STANDARD.) |
| NF L19-033-1993 | 航空航天系列.管状单元,挠性,玻璃纤维,酚醛树脂浸渍的蜂窝状材料.产品标准 | (AEROSPACE SERIES. HONEYCOMB MATERIALS WITH TUBULAR CELLS, FLEXIBLE, FIBRE GLASS, PHENOLIC RESIN IMPREGNATED. PRODUCT STANDARD.) |
| NF L19-037-1993 | 航空航天系列.管状单元,六角形,碳纤维,酚醛树脂浸渍的蜂窝状材料.产品标准 | (AEROSPACE SERIES. HONEYCOMB MATERIALS WITH TUBULAR CELLS, HEXAGONAL CARBON FABRIC, PHENOLIC RESIN IMPREGNATED ORIENTED AT PLUS OVER MINUS. PRODUCT STANDARD.) |
| NF L19-040-1993 | 航空航天系列.管状单元,六角形,玻璃纤维,酚醛树脂浸渍的蜂窝状材料,正负45度取向.产品标准 | (AEROSPACE SERIES. HONEYCOMB MATERIALS TUBULAR CELLS, HEXAGONAL, FIBRE GLASS, PHENOLIC RESIN IMPREGNATED, ORIENTED AT PLUS OVER MINUS 45 DEGREES. PRODUCT STANDARD.) |
| NF L19-041-1993 | 航空航天系列.管状单元,矩形,玻璃纤维,酚醛树脂浸渍的蜂窝状材料,正负45度取向.产品标准 | (AEROSPACE SERIES. HONEYCOMB MATERIALS WITH TUBULAR CELLS, RECTANGULAR, FIBRE GLASS, PHENOLIC RESIN IMPREGNATED, ORIENTED AT PLUS OVER MINUS 45 DEGREES. PRODUCT STANDARD.) |
| NF L19-046-1993 | 航空航天系列.管状单元,六角形,玻璃纤维,聚酰亚胺树脂浸渍的蜂窝状材料,正负45度取向.产品标准 | (AEROSPACE SERIES. HONEYCOMB MATERIALS WITH TUBULAR CELLS, HEXAGONAL, FIBRE GLASS, POLYMIMIDE RESIN IMPREGNATED, ORIENTED AT PLUS OVER MINUS 45 DEGREES. PRODUCT STANDARD.) |
| NF M81-814-1989 | 矿用提升钢丝绳.纤维组成.特性和试验 | (STRANDED WIRE ROPES FOR MINE HOISTING. FIBRE COMPONENTS. CHARACTERISTICS AND TESTS.) |
| NF M87-243-1-2003 | 石油和天然气工业.玻璃纤维增强塑料管.第1部分:词汇、符号、应用和材料 | (Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1 : vocabulary, symbols, applications and materials.) |
| NF M87-243-2-2003 | 石油和天然气工业.玻璃纤维增强塑料管系.第2部分:合格鉴定和制造 | (Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2 : qualification and manufacture.) |
| NF M87-243-3-2003 | 石油和天然气工业.玻璃纤维增强塑料管系.第3部分:系统设计 | (Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3 : system design.) |
| NF M87-243-4-2003 | 石油和天然气工业.玻璃纤维增强塑料管系.第4部分:制造、安装和运行 | (Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4 : fabrication, installation and operation.) |
| NF M88-557-1-2003 | 地上用玻璃纤维增强塑料槽罐和容器.第1部分:原材料.规格条件和验收条件 | (GRP tanks and vessels for use above ground - Part 1 : raw materials - Specification conditions and acceptance conditions.) |
| NF M88-558-2002 | 地面储存冷水用单壁截面结构玻璃纤维增强式水箱的规范 | (Specification for glass fibre reinforced cisterns of one piece and sectional construction, for the storage, above ground, of cold water.) |
| NF P15-202-1-1993 | 建筑工程.具有粘合剂的多孔矿物纤维覆盖物.第1部分:技术规范 | (DTU 27-1. BUILDING WORKS. COVERINGS FROM BLOWN-OUT MINERAL FIBRES WITH BINDER. PART 1 : TECHNICAL SPECIFICATIONS.) |
| NF P15-202-2-1993 | 建筑工程.私人合同.具有粘合料的多孔矿物纤维覆盖层.第2部分:特别条款 | (DTU 27-1. BUILDING WORKS. PRIVATE CONTRACTS. COVERINGS FROM BLOWN-OUT MINERAL FIBRES WITH BINDER. PART 2 : SPECIAL CLAUSES.) |
| NF P16-304-1997 | 地下排水管道用纤维水泥管.第1部分:重力循环系统用管子、接头和配件(欧洲标准EN 588-1) | (Fibre-cement pipes for sewers and drains. Part 1 : pipes, joints and fittings for gravity systems.) |
| NF P16-304-2-2002 | 排水管和下水道用纤维水泥管.第2部分:人孔和检查室 | (Fibre-cement pipes for drains and sewers - Part 2 : manholes and inspection chambers.) |
| NF P16-306-2000 | 建筑物排放系统的纤维混凝土管线和配件.交货的尺寸和技术条款 | (Fibre-cement pipes and fiftings for discharge systems for buildings - Dimensions and technical terms of delivery.) |
| NF P19-828-1999 | 预制混凝土制品.玻璃纤维增强水泥的工厂生产控制的一般规则 | (Precast concrete products - General rules for factory production control of glass-fibre reinforced cement.) |
| NF P19-829-2-1998 | 预制混凝土产品.玻璃增强混凝土的试验方法.新GRC清洗出法对纤维含量的测定 | (Precast concrete products. Test method for glass-fibre reinforced cement. Part 2 : measuring the fibre content in fresh GRC, “Wash out test“.) |
| NF P19-829-3-1998 | 预制混凝土产品.玻璃增强混凝土的试验方法.喷雾GRC纤维含量的测定 | (Precast concrete products. Test method for glass-fibre reinforced cement. Part 3 : measuring the fibre content of sprayed GRC.) |
| NF P19-829-5-1998 | 预制混凝土产品.玻璃纤维增强水泥的试验方法.第5部分:弯曲强度的试验.完全弯曲试验方法 | (Precast concrete products. Test method for glass-fibre reinforced cement. Part 5 : measuring bending strength, “Complete bending test“ method.) |
| NF P19-829-6-1998 | 预制混凝土产品.玻璃纤维增强水泥的试验方法.第6部分:干密度测定和浸入法水吸收的测定 | (Precast concrete products. Test method for glass-fibre reinforced cement. Part 6 : determination of the absorption of water by immersion and determination of the dry density.) |
| NF P24-504-2000 | 未增塑聚氯乙烯纤维门窗的外形.耐人工气候老化性测定 | (Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to artificial weathering.) |
| NF P30-303-1998 | 建筑物覆盖物.纤维混凝土屋顶挤压胶合板密封带材.规范.试验 | (Building covering. Extruded mastic sealing strips for fibre-cement roofing. Specifications. Tests.) |
| NF P33-301-1994 | 屋顶用纤维水泥成型板材和配件.产品规范和试验方法 | (Fibre-cement profiled sheets and fittings for roofing. Product specification and test methods.) |
| NF P33-302-1994 | 屋顶用纤维水泥石板及其配件.产品规范和试验方法 | (Fibre-cement slates and their fitting for roofing. Product specification and test methods.) |
| NF P33-401-2001 | 纤维水泥平板.产品规范和试验方法 | (Fibre-cement flat sheets - Product specifications and test methods.) |
| NF P37-417-1993 | 屋顶和盖板.与屋顶薄板连接的部件.用带竖立构件的玻璃纤维增强聚酯做的底层.定义..规范.试验方法 | (ROOFING AND CLADDING. PARTS JOINED TO A ROOF SHEETING. BASES MADE OF GLASS FIBLRE REINFORCED POLYESTER WITH UPSTAND. DEFINITION, SPECIFICATIONS, TEST METHODS.) |
| NF P38-301-2-1999 | 单层屋顶用透光异型塑料板.第2部分:玻璃纤维增强聚酯板试验方法和特殊要求 | (Light transmitting profiled plastic sheeting for single skin roofing. Part 2 : specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP).) |
| NF P38-402-1985 | 屋顶和护板.塑料.玻璃纤维增强半透明聚酯加肋板.尺寸特性 | (TRANSLUCENT GLASS FIBRE REINFORCED RIBBED POLYESTER SHEETS. DIMENSIONAL CHARACTERISTICS.) |
| NF P38-403-1983 | 玻璃纤维增强聚酯半透明波形板.尺寸特性 | (TRANSLUCENT GLASS-FIBER REINFORCED POLYESTER CORRUGATED SHEETS. DIMENSIONAL CHARACTERISTICS.) |
| NF P38-504-1984 | 玻璃纤维增强聚酯波形板或加肋板.分布荷载静力弯曲试验 | (GLASS FIBRE REINFROCED CORRUGATED OR RIBBED POLYESTER SHEETS. STATIC DEFLECTION TESTS UNDER DISTRIBUTED LOAD.) |
| NF P39-301-1979 | 称作纤维沥青板的纤维毛毡增强沥青盖板.规范 | (SHINGLES OF CELLULOSIC FIBRE REINFORCED BITUMEN FELT,DESIGNATED “CELLULOSE BASED BITUMEN SHINGLES“. SPECIFICATIONS.) |
| NF P41-302-1994 | 纤维水泥制品.压力管道和接头(欧洲标准EN 512) | (Fibre-cement products. Pressure pipes and joints.) |
| NF P41-302/A1-2002 | 纤维混凝土制品.压力管和连接件 | (Fibre-cement products - Pressure pipes and joints.) |
| NF P41-305-2001 | 纤维水泥管.敷设和现场施工指南 | (Fibre-cement pipelines - Guide for laying and on-site work practices.) |
| NF P72-203-1/A1-2003 | DTU 25.41.建筑工程.石膏纤维板施工.石膏墙板.第1部分:技术规范 | (DTU 25.41 - Building works - Gypsum plasterboard works - Gypsum wallboards - Part 1 : technical specifications.) |
| NF P72-203-2/A1-2003 | DTU 25.41.建筑工程.私人合同.石膏纤维板施工.石膏墙板.第2部分:特殊条款 | (DTU 25.41 - Building works - Private contracts - Gypsum plasterboard works - Gypsum wallboards - Part 2 : special clauses.) |
| NF P73-201-1-1994 | DTU 25-51.建筑工程.纤维灰浆和粉饰灰泥顶板.第1部分:技术规范 | (DTU 25-51. BUILDING WORKS. FIBROUS GYPSUM PLASTERWORK CEILINGS. PART 1 : TECHNICAL SPECIFICATIONS.) |
| NF P73-201-2-1994 | DTU25-51.建筑工程.私人合同.纤维状石膏天花板.第2部分:特殊条款 | (DTU 25-51. BUILDING WORKS. PRIVATE CONTRACTS. FIBROUS GYPSUM PLASTERWORK CEILINGS. PART 2 : SPECIAL CLAUSES.) |
| NF P73-301-1991 | 纤维灰浆和粉饰灰泥.纤维灰浆构件.装饰用板和构件 | (Fibrous plasterwork. Flat elements, shaped elements.) |
| NF P75-412-2002 | 建筑物用的绝热制品.工厂制作的木纤维(WF)膨胀的珍珠岩产品.规范 | (Thermal insulation products for buildings - Factory made wood fibre (WF) products - Specification.) |
| NF P75-422-2003 | 建筑设施用隔热产品.测定玻璃纤维网状物的机械特性 | (Thermal insulation products for building applications - Determination of the mechanical properties of glass fibre meshes.) |
| NF Q01-007-1977 | 纸张和纸板.纤维成分名称术语 | (PAPER AND BOARD.NOMENCLATURE FOR THE NAMES RELATING TO FIBRE COMPOSITION.) |
| NF Q03-033-1994 | 单面和单壁瓦楞纤维纸板耐压力的测定 | (Single-faced and single-wall corrugated fibreboard. Determination of flat crush resistance.) |
| NF Q03-041-1996 | 瓦楞纤维板.边缘耐压碎性的测定 | (Corrugated fibreboard. Determination of edgewise crush resistance (unwaxed edge method).) |
| NF Q03-068-1982 | 纸张和纸板试验.棉织物(纤维棉)和皱纹纸浸泡吸水性法定 | (PAPER AND BOARD TESTS. DETERMINATION OF ABSORPTION BY IMMERSION OF SOFT TISSUE AND CREPE PAPER.) |
| NF Q03-072-1984 | 纸张和纸板试验.棉织物(纤维棉)和皱纹纸、印刷纸、颜色纸物件油墨和颜色含量的测定 | (PAPER AND BOARD. TESTS FOR PAPER AND BOARD. DETERMINATION OF INKE AND DYE CONTENT OF PRINTED DYED OR COLOURED ARTICLES MADE OF SOFT TISSUE (CELLUCOTTON) AND CREPE PAPER.) |
| NF Q12-009-1993 | 纸和纸板.瓦楞纤维板.包装用三重内壁纤维瓦楞板 | (PAPER AND BOARD. CORRUGATED FIBER BOARD. CHARACTERISTICS OF TRIPLE WALL CORRUGATED FIBER BOARD FOR PACKAGING.) |
| NF Q50-012-1983 | 纤维素.测量纸浆兰色中的漫反射率 | (Cellulose. Measurement of diffuse blue reflectance factor of pulps.) |
| NF T03-400-1997 | 合成矿物纤维.在鼠肺中持续时间的测定.吸入试验 | (SYNTHETIC MINERAL FIBRES. DETERMINATION OF PULMONARY BIOPERSISTENCE IN THE RAT. INHALATION TEST.) |
| NF T03-410-1998 | 建筑结构爆破用合成矿物纤维.实验室条件下的可溶性.试验方法 | (SYNTHETIC MINERAL FIBERS FOR BLASTING IN BUILDING CONSTRUCTION. IN VITRO SOLUBILITY. TEST METHOD.) |
| NF T12-013-1961 | 纤维素纸浆.在72％硫酸中不溶性的测定 | (CELLULOSE. CELLULOSE PULPS. DETERMINATION OF INSOLUBLES IN 72 PER CENT SULPHURIC ACID.) |
| NF T12-014-1961 | 纤维素.植物原料.在７２％硫酸中不溶性的测定 | (CELLULOSE. PLANT RAW MATERIALS. DETERMINATION OF INSOLUBLES IN 72 PER CENT SULPHURIC ACID.) |
| NF T12-023-1982 | 纤维素.钙含量的测定.乙二胺四乙酸滴定法和火焰原子吸收光谱测定法 | (Cellulose. Determination of the calcium content. Edta titrimetric method and flame atomic absorption spectrometric method.) |
| NF T12-029-1982 | 纤维素.锰含量的测定.高碘酸钠分光光度法和火焰原子吸收分光光度法 | (Cellulose. Determination of the manganese content. Sodium periodate photometric method and flame atomic absorption spectrometric method.) |
| NF T25-001-1995 | 增强纤维.标准批量取样法 | (Reinforced fibres. Sampling plans applicable to received batches.) |
| NF T25-008-2001 | 塑料.增强纤维.短切原丝.松密度的测定 | (Plastics - Reinforcement fibres - Chopped strands - Determination of bulk density.) |
| NF T25-010-1997 | 增强纤维.机织织物.规范基础 | (Reinforcement fibres - Woven fabrics - Basis for a specification.) |
| NF T25-100-2003 | 碳纤维.密度的测定 | (Carbon fibre - Determination of density.) |
| NF T25-101-1986 | 碳纤维.碳纤维浸渍长丝纱的拉伸试验 | (CARBON FIBERS. CARBON FIBRE FILAMENT YARN TENSILE TEST.) |
| NF T25-102-1997 | 碳纤维.单丝样品抗拉性能的测定 | (CARBON FIBRE. DETERMINATION OF THE TENSILE PROPERTIES OF SINGLE-FILAMENT SPECIMENS.) |
| NF T25-103-1987 | 碳纤维.线密度的测定 | (Carbon fibers. Determination of linear density.) |
| NF T25-104-1996 | 碳纤维.尺寸的测定 | (Carbon fibre. Determination of size content.) |
| NF T25-110-2-1999 | 碳纤维纱.第2部分:试验方法和总规范 | (CARBON FIBRE YARNS. PART 2 : TEST METHODS AND GENERAL SPECIFICATIONS. (EUROPEAN STANDARD EN 13002-2).) |
| NF T25-202-1999 | 增强纺织纤维.织物.单位长度经纱和纬纱的纱数的测定 | (REINFORCEMENTS. WOVEN FABRICS. DETERMINATION OF NUMBER OF YARNS PER UNIT LENGTH OF WARP AND WELT.) |
| NF T25-206-1-2001 | 增强材料.多轴多股纤维织物规范.第1部分:名称与符号 | (Reinforcement - Specifications for multi-axial multi-ply fabrics - Part 1 : designation.) |
| NF T25-206-2-2001 | 增强材料.多轴多股纤维织物规范.第2部分:试验方法和一般要求 | (Reinforcement - Specifications for multi-axial multi-ply fabrics - Part 2 : methods of test and general requirements.) |
| NF T25-206-3-2001 | 增强材料.多轴多股纤维织物规范.第3部分:特殊要求 | (Reinforcement - Specifications for multi-axial multi-ply fabrics - Part 3 : specific requirements.) |
| NF T25-409-1-1999 | 对芳族聚酰胺纤维长纱线.第1部分:名称与符号 | (PARA-ARAMID FIBRE FILAMENT YARNS. PART 1 : DESIGNATION. (EUROPEAN STANDARD EN 13003-1).) |
| NF T25-409-2-1999 | 对芳族聚酰胺纤维长纱线.第2部分:试验方法和总规范 | (PARA-ARAMID FIBRE FILAMENT YARNS. PART 2 : METHODS OF TEST AND GENERAL SPECIFICATIONS. (EUROPEAN STANDARD EN 13003-2).) |
| NF T25-409-3-1999 | 对芳族聚酰胺纤维长纱线.第3部分:技术规范 | (PARA-ARAMID FIBRE FILAMENT YARNS. PART 3 : TECHNICAL SPECIFICATIONS. (EUROPEAN STANDARD EN 13003-3).) |
| NF T25-715-2003 | 高级工业陶瓷.陶瓷复合材料.增强纤维的试验方法.第5部分:室温下复丝束中长丝拉伸强度分布和断裂时拉伸应变 | (Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Part 5 : determination of distribution of tensile strength and of tensile strain to failure of filaments within) |
| NF T47-106-1988 | 合成纤维骨架输送带.抗张强度和伸长率.规范和试验方法 | (CONVEYOR BELTS WITH ARAMIDE CARCASSE. TENSILE STRENGTH AND ELONGATIONS. SPECIFICATIONS AND METHODS OF TEST.) |
| NF T50-062-2-2002 | 塑料.可比单点数据的采集和表示法.第2部分:长纤维增强塑料 | (Plastics - Acquisition and presentation of comparable single-point data - Part 2 : long-fibre-reinforced plastics.) |
| NF T51-005-3-1996 | 塑料.载荷下偏转温度的测定.第3部分:高强度热固性叠层板和长纤维增强塑料 | (Plastics. Determination of temperature of deflection under load. Part 3 : high-strength thermosetting laminates and long-fibre reinforced plastics.) |
| NF T51-034-4-1997 | 塑料.抗拉性能的测定.第4部分:正交同性和正交异性纤维增强塑料复合材料的试验条件.(欧洲标准EN ISO 527-4) | (Plastics. Determination of tensile properties. Part 4 : test conditions for isotropic and orthotropic fibre-reinforced plastic composites.) |
| NF T51-034-5-1997 | 塑料.抗拉性能的测定.第5部分:单向纤维增强塑料复合材料的试验条件(欧洲标准EN ISO 527-5) | (Plastics. Determination of tensile properties. Part 5 : test conditions for unidirectional fibre-reinforced plastic composites.) |
| NF T51-143-1974 | 塑料.聚酰胺载体.石墨碳黑和玻璃纤维成分的测定 | (PLASTICS. FILLED POLYAMIDES. DETERMINATION OF PERCENTAGES OF GRAPHITE OR CARBON BLACK AND FIBER GLASS.) |
| NF T51-144-1974 | 塑料.填充聚酰胺.二硫化钼和玻璃纤维百分比的测定 | (FILLED POLYAMIDES. DETERMINATION OF PERCENTAGES OF MOLYBDENE BISULFIDE AND FIBER GLASS.) |
| NF T51-351-1985 | 塑料.灰分比率的测定.未增塑醋酸纤维素 | (Plastics. Determination of ash. Unplasticized cellulose acetate.) |
| NF T51-352-1999 | 塑料.未增塑的醋酸纤维素.游离酸度的测定 | (PLASTICS. UNPLASTICIZED CELLULOSE ACETATE. DETERMINATION OF FREE ACIDITY. (EUROPEAN STANDARD EN ISO 1061).) |
| NF T51-356-1999 | 塑料.非增塑的醋酸纤维素.水分含量的测定 | (PLASTICS. UNPLASTICIZED CELLULOSE ACETATE. DETERMINATION OF MOISTURE CONTENT. (EUROPEAN STANDARD EN ISO 585).) |
| NF T51-357-1999 | 塑料.醋酸纤维素.模塑时粘度降低的测定 | (PLASTICS. CELLULOSE ACETATE. DETERMINATION OF VISCOSITY LOSS ON MOULDING. (EUROPEAN STANDARD EN ISO 1599).) |
| NF T51-358-1999 | 塑料.醋酸纤维素.利用加热的不同时期在模制样品生产时光吸收量的测定 | (PLASTICS. CELLULOSE ACETATE. DETERMINATION OF LIGHT ABSORPTION ON MOULDED SPECIMENS PRODUCED USING DIFFERENT PERIODS OF HEATING. (EUROPEAN STANDARD EN ISO 1600).) |
| NF T57-103-2000 | 纤维增强塑料复合材料.平面方向压缩性的测定 | (Fibre-reinforced plastic composites - Determination of compressive properties in the in-plane direction.) |
| NF T57-105-1998 | 纤维增强塑料复合材料.挠性性能的测定 | (Fibre-reinforced plastic composites - Determination of flexural properties.) |
| NF T57-153-1-2002 | 纤维增强塑料.试验板的制备方法.第1部分:通用条件 | (Fibre-reinforced plastics - Methods of producing test plates - Part 1 : general conditions.) |
| NF T57-153-2-2002 | 纤维增强塑料.试验板的生产方法.第2部分:接触模压法和喷射成形法 | (Fibre-reinforced plastics - Methods of producing test plates - Part 2 : contact and spray-up moulding.) |
| NF T57-153-3-2002 | 纤维增强塑料.试验板的生产方法.第3部分:湿压缩模塑法 | (Fibre-reinforced plastics - Methods of producing test plates - Part 3 : wet compression moulding.) |
| NF T57-153-5-2002 | 纤维增强塑料.试验板的生产方法.第5部分:长纤维卷绕法 | (Fibre-reinforced plastics - Methods of producing test plates - Part 5 : filament winding.) |
| NF T57-153-6-2003 | 纤维增强塑料.试验用板材的生产方法.第6部分:挤拉模塑法 | (Fibre-reinforced plastics - Methods of producing test plates - Part 6 : pultrusion moulding.) |
| NF T57-153-7-2002 | 纤维增强塑料.试验板的生产方法.第7部分:树脂压铸法 | (Fibre-reinforced plastics - Methods of producing test plates - Part 7 : resin transfer moulding.) |
| NF T57-153-9-2003 | 纤维增强塑料.试验板的制备方法.第9部分:GMT/STC模制 | (Fibre-reinforced plastics - Methods of producing test plates - Part 9 : moulding of GMT/STC.) |
| NF T57-155-1998 | 塑料.热塑铸模化合物.SMC中纤维湿气级别测定 | (Plastics. Thermoset moulding compounds. Determination of the degree of fibre wet out in SMC.) |
| NF T57-156-1998 | 塑料.纤维增强化合物.SMC、BMC和DMC压缩铸模试验板的制备 | (Plastics. Fibre reinforced composites. Preparation of compression moulded test plates of SMC, BMC and DMC.) |
| NF T57-210-1994 | 塑料管道系统.玻璃纤维增强塑料部件.用重力法测定组分用量 | (Plastics piping systems. Glass-reinforced plastics components. Determination of the amounts of constituents using the gravimetric method.) |
| NF T57-217-1996 | 塑料管道系统.玻璃纤维增强热固性塑料管.潮湿条件下蠕变因子的测定和长期指定环的硬度的计算 | (Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Determination of the creep factor under wet conditions and calculation of the long-term specific ring stiffness.) |
| NF T57-218-1996 | 塑料管道系统.玻璃纤维增强热固塑料(GFK).检验原有环挠曲的试验方法 | (Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Test method to prove the resistance to initial ring deflection.) |
| NF T57-220-1996 | 塑料管道系统.玻璃纤维增强热固性塑料(GRP)管.测定指定环初始硬度 | (Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Determination of initial specific ring stiffness.) |
| NF T57-221-1996 | 塑料管道系统.玻璃纤维增强热固塑料管和配件.短期内部压力下管壁密封性的检验的试验方法 | (Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes and fittings. Test methods to prove the leaktightness of the wall under short-term internal pressure.) |
| NF T57-222-1996 | 塑料管道系统.玻璃纤维增强热固塑料管.初始纵向拉伸性能的测定 | (Plastics piping systems. Glass-reinforced thermosetting plastics (grp) pipes. Determination of initial longitudinal tensile properties.) |
| NF T57-224-1997 | 塑料管道系统.玻璃纤维增强热固性塑料(GRP)构件.检验带有弹性密封件的刚性锁定的管套筒接头设计的试验方法 | (Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) components. Test methods to prove the design of rigid locked socket-and-spigot joints with elastomeric seals.) |
| NF T57-225-1997 | 塑料管道系统.玻璃纤维增强热固性塑料元件.验证胶合管套筒接头设计的测试方法 | (Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) components. Test methods to prove the design of cemented socket-and-spigot joints.) |
| NF T57-229-1997 | 塑料管道系统.玻璃纤维增强热固性塑料管.在化学环境下存放后相对弯曲蠕变系数的测定 | (Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) pipes. Determination of the relative flexural creep factor following exposure to a chemical environment.) |
| NF T57-303-1989 | 塑料.碳纤维增强复合材料.层间剪切应力的测定.短跨距弯曲的方法 | (PLASTICS. CARBON REINFORCED COMPOSITES. DETERMINATION OF INTERLAMINAR SHEAR STRENGTH. FLEXURE METHOD WITH SHORT SPAN LENGHT.) |
| NF T57-404-2002 | 纤维增强塑料复合材料.无定向性增强材料的模型I层间断裂韧度G | (Fibre-reinforced composites - Determination of mode I interlaminar fracture toughness, Gic, for unidirectionally reinforced materials.) |
| NF T57-502-1995 | 增强纤维.玻璃纤维.丙酮中溶解物百分率的测量.烧瓶法 | (Reinforcement fibres. Glass fibre. Measurement of the percentage of soluble sizing in acetone. Flask method.) |
| NF T57-608-1999 | 纤维增强塑料.模压化合物和聚酯胶片.树脂、增强纤维和矿物填料含量的测定.溶解方法 | (Fibre-reinforced plastics. Moulding compounds and prepregs. Determination of resin, reinforced-fibre and mineral-filler content. Dissolution methods.) |
| NF T57-615-1997 | 纤维增强塑料.热固模塑混合物和预浸料.流动性和贮藏寿命的测定(欧洲标准EN ISO 12115) | (FIBRE-REINFORCED PLASTICS. THERMOSETTING MOULDING COMPOUNDS AND PREPREGS. DETERMINATION OF FLOWABILITY AND SHELF LIFE. (EUROPEAN STANDARD EN ISO 12115).) |
| NF T57-901-1997 | 玻璃纤维增强塑料(GRP)制地下油罐.单面处于液体环境的试验方法 | (Underground tanks of glass-reinforced plastics (GRP). Method for one side exposure to fluids.) |
| NF T57-902-1997 | 玻璃纤维增强塑料(GRP)制地下油罐.系数α和β的测定 | (Underground tanks of glass-reinforced plastics (GRP). Determination of factor alpha and factor beta.) |
| NF V03-003-2001 | 食品.照射食品中纤维素含量的探测.ESR的光谱色谱分析法 | (Foodstuffs - Detection of irradiated food containing cellulose by ESR spectroscopy.) |
| NF V03-040-1993 | 农产食品.粗纤维含量的测定.通用方法 | (Agricultural food products. Determination of crude fibre. General method.) |
| NF V03-041-1981 | 农产食品.粗纤维含量的测定.改进的Scharrer方法 | (Agricultural food products. Determination of crude fibre. Modified scharrer method.) |
| NF V18-099-2002 | 动物饲料.粗纤维含量测定.中间过滤法 | (Animal feeding stuffs - Determination of crude fibre content - Method with intermediate filtration.) |
| NF X41-600-1971 | 纤维素织物（天然或合成）抗微生物侵蚀的试验子和菌丝混合培植法 | (TESTS FOR THE RESISTANCE TO MICRO-ORGANISMS OF NATURAL OR ARTIFICIAL CELLULOSE TEXTILES. METHOD BY MIXED INOCULATION (SPORES/MYCELLIUM).) |
| NF X41-601-1-2001 | 纺织品.含纤维素织物对微生物耐性的测定.土壤埋试验.第1部分:腐烂延迟完成的评价 | (Textiles - Determination of the resistance of cellulose-containing textiles to micro-organisms - Soil burial test - Part 1 : assessment of rot-retardant finishing.) |
| NF X41-602-1971 | 纤维素织物（天然或合成）抗微生物侵蚀的试验.置于热室中 | (TESTS FOR THE RESISTANCE TO MICRO-ORGANISMS OF NATURAL OR ARTIFICIAL CELLULOSE TEXTILES. EXPOSURE IN A CHAMBER WITH TROPICAL ATMOSPHERE.) |
| NF X41-603-1976 | 纺织品的防护.航海用天然纤维绳缆抗微生物侵蚀的试验方法 | (PROTECTION OF TEXTILES. METHOD OF TEST FOR THE RESISTANCE TO MICROORGANISMS OF NATURAL FIBRE ROPES AND CORDAGE INTENTED FOR MARINE USE.) |
| NF X43-050-1996 | 空气质量.用电子显微镜传送法测定石棉纤维的浓度.间接法 | (Air quality. Determination of the asbestos fiber concentration by transmission electron microscopy. Indirect method.) |
| P15-202-1993 | DTU 27-1.建筑工程.带胶粘剂的防喷矿物纤维制成的覆面.第1部分:技术规范.第2部分:特别条款 | (DTU 27-1. Building works. Coverings from blown-out mineral fibres with binder. Part 1 : technical specifications - Part 2 : special clauses.) |
| XP P 30-311-1997 | 屋顶.固定件.组件抗性测定.皱状纤维混凝土.拉力负荷测定的测试方法 | (ROOFING. FASTENERS. DETERMINATION OF THE CHARACTERISTIC RESISTANCE OF THE ASSEMBLY. CORRUGATED FIBRE CIMENT. TEST METHOD TO DETERMINE PULL-OVER LOAD.) |
| 编号 | 中文名称 | 英文名称 |