| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| ANSI ATIS0900002-2009 | 同步标准.办公室内基于以太网的时间分配用物理互连 | Synchronization Standard - Physical Interconnection for Intra-Office Ethernet-based Timing Distribution |
| ANSI ATIS1000026-2008 | 时间/边界控制功能和要求 | Sessions/Border Control Functions and Requirements |
| ANSI C37.06.1-2000 | 快速瞬时恢复压升时间(非美国标准)用指定对称电流基础额定值的高压断路器试用指南 | High-Voltage Circuit Breakers Rated on a Symetrical Current Basis Designated Definite Purpose for Fast Transient Recovery Voltage Rise Times |
| ANSI INCITS 310-1998(R2003) | 信息技术用美国国家标准.信息交换时间的表示 | for Information Technology – Representation of Time for Information Interchange |
| ANSI INCITS310-1998 | 信息技术.信息交换用时间的表示法 | Information Technology - Representation of Time for Information Interchange |
| ANSI INCITS346-2001 | 信息技术.防护区运行时间接口扩展服务(PARTIES) | Information Technology - Protected Area Run Time Interface Extension Services (PARTIES) |
| ANSI ISO 19108-2002(R2008) | 地理信息.时间计划 | Geographic information — Temporal schema |
| ANSI NCITS 310-1998 | 信息技术.信息交换用时间的表示 | Information Technology - Representation of Time for Information Interchange |
| ANSI X9.95-2005 | 可信时间戳管理和安全 | Trusted Time Stamp Management and Security |
| ANSI/(NFPA) T3.21.8-2008 | 气液传动.响应时间的测量.方向控制阀 | Pneumatic fluid power - Measurement of response time - Directional control valves |
| ANSI/ANS 58.8-1994 | 核电站.有关安全操作人员行为的时间响应设计准则 | Nuclear Power Plants – Time Response Design Criteria for Safety Related Operator Actions |
| ANSI/ASTM D1901-2000 | 卤化有机溶剂及其搀合物相对蒸发时间测试方法 | Test Method for Relative Evaportation Time of Halogenated Organic Solvents and their Admixtures |
| ANSI/ASTM D2471-1999 | 活性热固树脂胶凝时间和最大放热温度测试方法(08.02) | Test Method for Gel Time and Peak Exothermic Temperature of Reacting Thermosetting Resins (08.02) |
| ANSI/ASTM D3056-2005 | 无溶剂清漆胶凝时间的试验方法 | Test Method for Gel Time of Solventless Varnishes |
| ANSI/ASTM D3895-1998 | 热分析法测定聚烯烃氧化感应时间的方法 | Test Method for Oxidative Induction Time of Polyolefins by Thermal Analysis (08.03) |
| ANSI/ASTM D5455-1993 | 短时间里液体被吸入纸内的试验方法(BRISTOW试验) | Test Method for Short-Term Liquid Sorption Into Paper (Bristow Test) |
| ANSI/ASTM D635-1998 | 水平位置自支撑式塑料的燃烧率和/或燃烧程度与燃烧时间测试验方法 | Test Method for Rate of Burning and/or Extent and Time of Burning of Self-Supporting Plastics in a Horizontal Position (08.01) |
| ANSI/ASTM E1666-1995 | 办公设施关于正常时间或条件以外的工作的适用性分类 | Classification for the Serviceability of an Office Facility for Work Outside Normal Hours or Conditions (04.11) |
| ANSI/ASTM E1666-1995A | 办公设施关于正常时间或条件以外的工作的适用性分类 | Classification for the Serviceability of an Office Facility for Work Outside Normal Hours or Conditions |
| ANSI/ASTM E1666a-1995 | 办公设施正常时间和条件以外工作的功能分类(04.11) | Classification for the Serviceability of an Office Facility for Work Outside Normal Hours or Conditions (04.11) |
| ANSI/ASTM E292-2001 | 材料断裂缺口拉伸试验执行时间测试方法 | Test Methods for Conducting Time for Rupture Notch Tension Tests of Materials |
| ANSI/ASTM F2018-2000 | 使用水平应力拉伸样品测定塑料失效时间的试验方法 | Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens |
| ANSI/ASTM F948-1994 | 固定流体内压下塑料管道系统和组件失效时间-试验方法 | Test Method for Time-to-Failure of Plastic Piping Systems and Components under Constant Internal Pressure with Flow |
| ANSI/ATIS 1000026-2008 | 时间/边界控制功能和要求 | Sessions/Border Control Functions and Requirements |
| ANSI/AWWA C750-2003 | 全闭路导管中运送时间流量计 | Transit-Time Flowmeters in Full Closed Conduits |
| ANSI/EIA 364-102-1998 | 电连接器、插孔、电缆组件或互连装置的上升时间衰减试验程序 | Rise Time Degradation Test Procedure for Electrical Connectors, Sockets, Cable Assemblies or Interconnection Systems |
| ANSI/EIA-364-102-1998 | 电连接器、插座、电缆附件或互连系统上升时间降低试验程序 | Rise Time Degradation Test Procedure for Electrical Connectors, Sockets, Cable Assemblies or Interconnection Systems |
| ANSI/EIA-364-108-2000 | 电连接器、电缆附件或互连系统在时间和频率域中测量的阻抗、反射系数、回程损耗和VSWR试验程序 | Impedance, Reflection Coefficient, Return Loss, and VSWR Test Procedure Measured in the Time and Frequency Domain for Electrical Connectors, Cable Assemblies or Interconnection Systems |
| ANSI/IEEE 1139-2008 | 基本频率和时间计量学用物理量标准定义.随机不稳定性 | Standard Definitions of Physical Quantities for Fundamental Frequency and Time Metrology - Random Instabilities |
| ANSI/IEEE 1646-2004 | 电力变电所自动化用标准通讯传输时间性能要求 | Standard Communication Delivery Time Performance Requirements for Electric Power Substation Automation |
| ANSI/IEEE C37.20.1a-2005 | 金属壳密封的低压电力线路断路器开关设备标准.修改1:短时间和短路可耐电流测试;多电缆连接的最小区域 | Standard for Metal-Enclosed Low-Voltage Power Circuit Breaker Switchgear - Amendment 1: Short-Time and Short-Circuit Withstand Current Tests; Minimum Areas for Multiple Cable Connections |
| ANSI/IEEE C57.109-1993 | 液浸式变压器穿越故障电流持续时间的指南 | Guide for Liquid-Immersed Transformer Through-Fault Current Duration |
| ANSI/IEEE C57.12.59-2002 | 干式变压器全故障电流持续时间指南 | Guide for Dry-Type Transformer Through-Fault Current Duration |
| ANSI/INCITS/ISO/IEC 18014-2-2002 | 信息技术.保密技术.时间标记业务.第2部分:产生独立标权的机构 | Information technology - Security techniques - Time-stamping services - Part 2: Mechanisms producing independent tokens |
| ANSI/INCITS/ISO/IEC 18014-3-2004 | 信息技术.安全技术.时间标记业务.第3部分:产生链接标记的机制 | Information technology - Security techniques - Time-stamping services - Part 3: Mechanisms producing linked tokens |
| ANSI/ISO/IEC 13818-9-1996 | 信息技术.移动画面和有关音频信息的通用编码.第9部分:系统解码器的实时时间接口的拓展 | Information technology - Generic coding of moving pictures and associated audio information - Part 9: Extension for real time interface for systems decoders |
| ANSI/UL 796a-2007 | 印制电路板的安全标准(提议时间2007.09.28) | Standard for Safety for Printed-Wiring Boards (Proposal dated September 28, 2007) |
| ASME MFC-5M-1985 | 在封闭导管中用渡越时间超声波流量计测量液体流量 | (Measurement of liquid flow in closed conduits using transit-time ultrasonic flowmeters) |
| ASME Y10.3M-1984 | 机械和与时间相关的现象用字母符号 | (Letter symbols for mechanics and time-related phenomena) |
| ASTM C1291-2000a(2005) | 高级单片陶瓷的高温抗拉蠕变应变,蠕变应变率及蠕变断裂时间的标准试验方法 | Standard Test Method for Elevated Temperature Tensile Creep Strain, Creep Strain Rate, and Creep Time-to-Failure for Advanced Monolithic Ceramics |
| ASTM C1398-2007 | 用吉尔摩(Gillmore)针法测定喷浆用含添加剂水硬水泥灰浆凝固时间的实验室标准试验方法 | Standard Test Method for The Laboratory Determination of the Time of Setting of Hydraulic-Cement Mortars Containing Additives for Shotcrete by the Use of Gillmore Needles |
| ASTM C308-2000(2005) | 耐化学腐蚀树脂灰浆施工时间、凝固时间及维护凝固强度时间的标准试验方法 | Standard Test Methods for Working, Initial Setting, and Service Strength Setting Times of Chemical-Resistant Resin Mortars |
| ASTM C953-2006 | 实验室内测定预置集料混凝土的灌浆料凝固时间的标准试验方法 | Standard Test Method for Time of Setting of Grouts for Preplaced-Aggregate Concrete in the Laboratory |
| ASTM D1363-2006 | 丙铜和甲醇的高锰酸盐时间的标准测试方法 | Standard Test Method for Permanganate Time of Acetone and Methanol |
| ASTM D1545-2007 | 用起泡时间法测定透明液体粘度的标准试验方法 | Standard Test Method for Viscosity of Transparent Liquids by Bubble Time Method |
| ASTM D1721-1997(2007) | 磷酸三甲苯酯的高锰酸盐时间的测试方法 | Standard Test Method for Permanganate Time of Tricresyl Phosphate |
| ASTM D1901-2000(2004) | 卤化有机溶剂及其添加剂相对蒸发时间的标准试验方法 | Standard Test Method for Relative Evaporation Time of Halogenated Organic Solvents and Their Admixtures |
| ASTM D2396-1994(2004) | 用转矩流变仪测定聚氯乙烯(PVC)粉末混合时间的标准试验方法 | Standard Test Methods for Powder-Mix Time of Poly(Vinyl Chloride) (PVC) Resins Using a Torque Rheometer |
| ASTM D3014-2004a | 硬质热固性泡沫塑料在垂直状态时火焰高度、燃烧时间和质量损失的标准试验方法 | Standard Test Method for Flame Height, Time of Burning, and Loss of Mass of Rigid Thermoset Cellular Plastics in a Vertical Position |
| ASTM D3056-2005 | 无溶剂清漆凝固时间的标准试验方法 | Standard Test Method for Gel Time of Solventless Varnishes |
| ASTM D3732-1982(2005) | 紫外线固化涂料固化时间的报告 | Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings |
| ASTM D3895-2007 | 用差示扫描量热法测定聚烯烃的氧化感应时间的标准试验方法 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
| ASTM D4217-2007 | 热固涂料粉末的胶凝时间用标准试验方法 | Standard Test Method for Gel Time of Thermosetting Coating Powder |
| ASTM D4497-1994(2004)e1 | 热熔胶粘剂断开时间测定的标准试验方法(手工法) | Standard Test Method for Determining the Open Time of Hot Melt Adhesives (Manual Method) |
| ASTM D4680-1998(2004) | 用压缩负荷静剪切法法测定胶粘剂蠕变和老化时间的标准试验方法(木材对木材) | Standard Test Method for Creep and Time to Failure of Adhesives in Static Shear by Compression Loading (Wood-to-Wood) |
| ASTM D5405-1998(2004) | 非沥青质有机屋面薄膜材料接缝的蠕变断裂时间标准试验方法 | Standard Test Method for Conducting Time-to-Failure (Creep-Rupture) Tests of Joints Fabricated from Nonbituminous Organic Roof Membrane Material |
| ASTM D5455-1993(2003) | 纸中短时间液体吸附的标准试验方法(BRISTOW试验) | Standard Test Method for Short-Term Liquid Sorption Into Paper (Bristow Test) |
| ASTM D5885-2006 | 用高压差示扫描量热法测定聚烯烃土工合成织物的氧化感应时间的标准试验方法 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry |
| ASTM D5909-1996a(2006) | 用角鲨烯抗性测试氧化物干燥印刷油墨干燥时间的标准试验方法 | Standard Test Method for Drying Time of Oxidative-Drying Printing Inks by Squalene Resistance |
| ASTM D6325-1998(2004) | 测定地毯胶合铺料粘合剂的开放装配时间的试验方法 | Test Method for Determining Open Assembly Time of Carpet Mastic Adhesives |
| ASTM D635-2006 | 塑料在水平状态时的燃烧速率或者燃烧蔓延程度及燃烧时间的标准试验方法 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position |
| ASTM D6383-1999(2005) | 由EPDM屋顶膜材料制造的胶粘剂接头的失效时间(蠕变破裂)的标准操作规程 | Standard Practice for Time-to-Failure (Creep-Rupture) of Adhesive Joints Fabricated from EPDM Roof Membrane Material |
| ASTM D6780-2005 | 时间域反射测量法现场测定土壤含水量和密度的标准试验方法 | Standard Test Method for Water Content and Density of Soil in Place by Time Domain Reflectometry (TDR) |
| ASTM D6815-2002a | 木制和木基产品的荷载和蠕变效应的持续时间的评价的标准规范 | Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based Products |
| ASTM D6820-2002(2007) | 次表面探查用时间域电磁法的使用标准指南 | Standard Guide for Use of the Time Domain Electromagnetic Method for Subsurface Investigation |
| ASTM D711-1989(2004) | 路标漆不粘着时间的试验方法 | Standard Test Method for No-Pick-Up Time of Traffic Paint |
| ASTM D7134-2005 | 用矩阵辅助激光解吸/离子化(MALDI)-飞行时间(TOF)质谱(MS)法测定无规立构聚苯乙烯的平均分子量和分子量分布 | Standard Test Method for Molecular Mass Averages and Molecular Mass Distribution of Atactic Polystyrene by Matrix Assisted Laser Desorption/Ionization (MALDI)-Time of Flight (TOF) Mass Spectrometry (MS) |
| ASTM D7278-2006 | 分析仪抽样系统迟延时间预测的标准指南 | Standard Guide for Prediction of Analyzer Sample System Lag Times |
| ASTM D7406-2007 | 土工合成排水产品用常压下随时间变化的(蠕变)变形用标准试验方法 | Standard Test Method for Time-Dependent (Creep) Deformation Under Constant Pressure for Geosynthetic Drainage Products |
| ASTM E1666-1995a(2005) | 办公设备对于正常时间或条件以外的工作的适用性标准分类 | Standard Classification for Serviceability of an Office Facility for Work Outside Normal Hours or Conditions |
| ASTM E1860-2007 | 消逝时间校正热分析仪的标准试验方法 | Standard Test Method for Elapsed Time Calibration Thermal Analyzers |
| ASTM E1909-1997(2003) | 感官特征时间强度评价的标准指南 | Standard Guide for Time-Intensity Evaluation of Sensory Attributes |
| ASTM E2109-2001(2007) | 用热分析法测定反应感应时间的标准试验方法 | Test Methods for Determining Area Percentage Porosity in Thermal Sprayed Coatings |
| ASTM E2426-2005 | 用SIMS测量同位素比率对脉冲计算系统死时间测定的标准实施规程 | Standard Practice for Pulse Counting System Dead Time Determination by Measuring Isotopic Ratios with SIMS |
| ASTM F1260M-1996(2003) | 集成电路金属喷镀总量和电迁移中值失效时间的评定标准试验方法(米制单位) | Standard Test Method for Estimating Electromigration Median Time-to-Failure and Sigma of Integrated Circuit Metallizations [Metric] |
| ASTM F1536-1995(2005) | 水激活合成聚氨酯玻璃纤维矫型铸带强度和凝固时间测定的标准试验方法 | Standard Test Method for Determining Strength and Setting Time of Synthetic Water-Activated Polyurethane Fiberglass Orthopaedic Casting Tape |
| ASTM F2018-2000(2006) | 使用平应力拉伸样品测定塑料老化时间的标准试验方法 | Standard Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens |
| ASTM F2382-2004e1 | 根据部分促凝血酶原激酶时间评估血管内医疗设备材料的标准试验方法 | Standard Test Method for Assessment of Intravascular Medical Device Materials on Partial Thromboplastin Time (PTT) |
| ASTM F2498-2005 | 用烟熏法测定喷墨介质和墨水的干燥时间的标准实施规程 | Standard Practice for Determining the Drying Time of Inkjet Media and Inks Using a Smudge Method |
| ASTM F948-1994(2006) | 在恒定内流动压力下塑料管道系统和组件损坏时间的标准试验方法 | Standard Test Method for Time-to-Failure of Plastic Piping Systems and Components Under Constant Internal Pressure With Flow |
| ASTM G84-1989(2005) | 在大气腐蚀测试中表面暴露在潮湿条件下湿润时间的测量 | Standard Practice for Measurement of Time-of-Wetness on Surfaces Exposed to Wetting Conditions as in Atmospheric Corrosion Testing |
| IEEE 1139-1999 | 基本频率和时间计量学用物理量定义.随机不稳定性 | (Definitions of physical quantities for fundamental frequency and time metrology - Random instabilities) |
| IEEE C 37.112-1996 | 过流继电器反向时间特性方程式 | (Inverse-time characteristic equations for overcurrent relays) |
| IEEE C 57.12.59-2001 | 干式变压器直通故障电流持续时间指南 | (Guide for dry-type transformer through-fault current duration) |
| UL 863-1997 | 时间显示和记录装置 | (Time-indicating and -recording appliances ) |
| 编号 | 中文名称 | 英文名称 |