| 编号 | 中文名称 | 英文名称 |
|---|---|---|
| BS 1041-7-1988 | 温度测量.第7部分:温度/时间指示器的选择和使用指南 | Temperature measurement - Guide to selection and use of temperature/time indicators |
| BS 1743-4-1980 | 奶粉和奶粉制品的分析方法.第4部分:速溶奶粉的可分散性和浸湿时间的测定 | Methods for analysis of dried milk and dried milk products - Determination of the dispersibility and the wetting time of instant dried milk |
| BS 2782-1 Methods 134A and 134B-1992 | 塑料试验方法.第1部分:热性能.方法134A:热塑塑料氧化感应时间测定 | Methods of testing plastics - Thermal properties - Determination of the oxidation induction time of thermoplastics |
| BS 2782-8 Method 835A-1980 | 塑料的试验方法.其他特性.酚醛树脂胶凝时间的测定 | Methods of testing plastics - Other properties - Determination of gelation time of phenolic resins |
| BS 2782-8 Method 835B-1980 | 塑料的试验方法.其他特性.聚酯树脂胶凝时间的测定(手工方法) | Methods of testing plastics - Other properties - Determination of gelation time of polyester resins (manual method) |
| BS 2782-8 Method 835D-1980 | 塑料试验方法.第8部分:其他性能.试验方法835D:用热板测定热固性树脂胶凝时间 | Methods of testing plastics - Other properties - Determination of gelation time of thermosetting resins using a hot plate |
| BS 2846-8-2001 | 数据统计分析说明指南.中值.估计和置信度间隔时间 | Guide to statistical interpretation of data - Median - Estimation and confidence intervals |
| BS 3375-5-1997 | 管理服务.第5部分:工作度量中考验极限、恢复时间和放松时间测定指南 | Management services - Guide to determination of exposure limits, recovery times and relaxation times in work measurement |
| BS 3712-3-1974 | 建筑施工用密封胶.第3部分:使用寿命,结皮特性和粘性消失时间试验方法 | Building and construction sealants - Methods of test for application life, skinning properties and tack-free time |
| BS 3900-C1-1965 | 涂料试验方法.涂料膜形成试验.湿边时间 | Methods of test for paints - Tests associated with paint film formation - Wet edge time |
| BS 3900-J3-1998 | 涂料试验方法.涂粉试验.第J3部分:涂层粉末凝胶时间测定 | Methods of test for paints - Testing of coating powders - Determination of gel time of coating powders |
| BS 5350-B5-1976 | 粘合剂试验方法.第B5部分:胶凝时间的测定 | Methods of test for adhesives - Determination of gelation time |
| BS 5350-H4-1984 | 粘合剂试验方法.第H4部分:物理试验.最大断开时间测定(热炉法) | Methods of test for adhesives - Physical tests on hot-melt adhesives - Determination of maximum open time of hot-melt adhesives (oven method) |
| BS 5459-2-2000+A2-2008 | 办公家具性能要求和试验规范.体重在150kg以下人员每天使用时间小于24小时的办公室支架座椅并包括单个部件类 | Specification for performance requirements and tests for office furniture - Office pedestal seating for use by persons weighing up to 150kg and for use up to 24 hours a day, including type-approval tests for individual components |
| BS 5857-1.4-1980 | 密封管道中流体流量的示踪剂测量法.第1部分:水流量测量.第4节:非放射性示踪剂渡越时间法 | Methods for measurement of fluid flow in closed conduits, using tracers - Measurement of water flow - Transit time method using non-radioactive tracers |
| BS 5857-1.5-1980 | 密封管道中流体流量的示踪剂测量法.第1部分:水流量测量.第5节:放射性示踪剂渡越时间法 | Methods for measurement of fluid flow in closed conduits, using tracers - Measurement of water flow - Transit time method using radioactive tracers |
| BS 5857-2.4-1980 | 使用示踪剂的密封管道中流体流量的测量方法.气体流量的测量.采用放射性示踪剂的过渡时间法 | Methods for measurement of fluid flow in closed conduits, using tracers - Measurement of gas flow - Transit time method using radioactive tracers |
| BS 6288-10-1989 | 磁带录放系统.第10部分:时间和地址码规范 | Magnetic tape sound recording and reproducing systems - Specification for time and address codes |
| BS 6392-9-1983 | 工业用乙醇试验.第9部分:用高锰酸盐退色时间的方法来测定乙醇含量 | Testing of ethanol for industrial use - Method for determination of permanganate time |
| BS 6662-1985 | 低压电源和信号线路的短时间瞬态测量方法指南 | Guide to methods of measurement of short duration transients on low voltage power and signal lines |
| BS 684-1.7-1976 | 脂肪和油脂的分析方法.物理法.表面干燥时间的测定 | Methods of analysis of fats and fatty oils - Physical methods - Determination of surface-drying time |
| BS 7346-5-2005 | 烟和热控制系统部件.利用时间相关设计点火法的排烟和排热通风系统的功能推荐方法和计算方法.实施规程 | Components for smoke and heat control systems - Functional recommendations and calculation methods for smoke and heat exhaust ventilation systems, employing time-dependent design fires - Code of practice |
| BS 7899-2-1999 | 火灾对生命和健康造成危害的评定实施规程.生命和健康受到危害的鉴定以及火灾中丧失能力和死亡的时间估算方 | Code of practice for assessment of hazard to life and health from fire - Guidance on methods for the quantification of hazards to life and health and estimation of time to incapacitation and death in fires |
| BS 8452-2005 | 液体装置用夹件(外部安装)渡越时间测量技术的使用.指南 | Use of clamp-on (externally mounted) transit time metering techniques for liquid applications - Guide |
| BS CWA 14172-8-2004 | EESSI合格评定指南.时间标记特许设备和方法 | EESSI conformity assessment guidance - Time-stamping authority services and processes |
| BS DD CEN/TS 14751-2004 | 焊接.焊接检验用飞行时间衍射技术(TOFD)的使用 | Welding - Use of time-of-flight diffraction technique (TOFD) for examination of welds |
| BS DD ENV 1156-1999 | 木基板.负荷持续时间和蠕变因子的测定 | Wood-based panels - Determination of duration of load and creep factors |
| BS DD ENV 302-5-2002 | 承载木结构用粘合剂.试验方法.传统组装时间的测定 | Adhesives for load-bearing timber structures - Test tethods - Determination of the conventional assembly time |
| BS DD IEC/PAS 61280-2-10-2003 | 纤维光学通信子系统试验程序.数字系统.激光发射机的时间分辨线性调频脉冲和α因数测量 | Fibre optic communication subsystem test procedures - Digital systems - Time-resolved chirp and alpha-factor measurement of laser transmitters |
| BS DD IEC/TS 61934-2006 | 电子绝缘材料和系统.在短上升时间和反复电压脉冲下局部放电(PD)的电子测量 | Electrical insulating materials and systems - Electrical measurement of partial discharges (PD) under short rise time and repetitive voltage impulses |
| BS EN 1015-9-1999 | 砖石工程用砂桨的试验方法.新凝砂桨使用寿命和校正时间的测定 | Methods of test for mortar for masonry - Determination of workable life and correction time of fresh mortar |
| BS EN 116000-2-1986 | 电子元器件质量评定协调体系.总规范:全有或全无机电继电器.时间延迟继电器的总数据和试验方法 | Harmonized system of quality assessment for electronic components - Generic specification: electromechanical all-or-nothing relays - Generic data and methods of test for time delay relays |
| BS EN 12189-1999 | 混凝土结构的防护和修整用的产品和系统.试验方法.敞开时间的测定 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of open time |
| BS EN 12381-2005 | 健康信息学.健康护理特殊问题的时间标准 | Health informatics - Time standards for healthcare specific problems |
| BS EN 12846-2002 | 汽油及其产物的试验方法.沥青和沥青粘合剂.利用射流粘度计测定沥青乳化液的射流时间 | Methods of test for petroleum and its products - Bitumen and bituminous binders - Determination of efflux time of bitumen emulsions by the efflux viscometer method |
| BS EN 13294-2002 | 混凝土结构的防护和修整用产品和系统.试验方法.凝固时间的测定 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of stiffening time |
| BS EN 13319-2000 | 潜水设备附件.深度仪和深度及时间组合测量设备.功能和安全性要求、试验方法 | Diving accessories - Depth gauges and combined depth and time measuring devices - Functional and safety requirements, test methods |
| BS EN 13357-2003 | 石油及其制品的试验方法.沥青和沥青粘合剂.石油轻制和软制沥青流出时间的测定 | Methods of test for petroleum and its products - BS 2000-502: Bitumen and bituminous binders - Determination of the efflux time of petroleum cut-back and fluxed bitumens |
| BS EN 13409-2002 | 液压固化地板修平和/或整平复合物的试验方法.凝固时间测定 | Methods of test for hydraulic setting floor smoothing and/or levelling compounds - Determination of setting time |
| BS EN 1346-2007 | 瓷砖用粘合剂.敞露时间的测定 | Adhesives for tiles - Determination of open time |
| BS EN 13630-12-2003 | 民用爆炸物.导爆索和保险引信.测定保险引信的燃烧持续时间 | Explosives for civil uses - Detonating cords and safety fuses - Determination of burning duration of safety fuses |
| BS EN 13850-2002 | 邮政服务设施.服务质量.单件优先邮件和一级邮件的两点传送时间的计算 | Postal services - Quality of service - Measurement of the transit time of end-to-end services for single piece priority mail and first class mail |
| BS EN 13938-3-2003 | 民用爆炸物.推进剂和火箭推进剂.爆燃到爆炸过渡时间的测定 | Explosives for civil uses - Propellants and rocket propellants - Determination of deflagration to detonation transition |
| BS EN 14089-2002 | 航天产品质量保证.有限定时间的库存材料的控制 | Space product assurance - The control of limited shelf-life materials |
| BS EN 14117-2004 | 混凝土结构的保护和维修用产品和系统.试验方法.粘结性注入产品的流出时间测定 | Products and systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products |
| BS EN 14179-1-2005 | 建筑物玻璃.长时间热处理的热钢化钙钠硅酸盐安全玻璃.定义和描述 | Glass in building - Heat-soaked thermally-toughened soda lime silicate safety glass - Definition and description |
| BS EN 14179-2-2005 | 建筑物玻璃.长时间热处理的热钢化钙钠硅酸盐安全玻璃.合格评定/产品标准 | Glass in building - Heat-soaked thermally-toughened soda lime silicate safety glass - Evaluation of conformity/product standard |
| BS EN 14187-2-2003 | 冷用密封胶.消粘时间测定的试验方法 | Cold applied joint sealants - Test method for the determination of tack free time |
| BS EN 14508-2003 | 邮政服务.服务质量.单件非优先邮件和二级邮件全程服务运送时间的测量 | Postal services - Quality of service - Measurement of the transit time of end-to-end services for single piece non-priority mail and second class mail |
| BS EN 14701-1-2006 | 淤泥特性.过滤性能.第1部分:毛细管抽吸时间(CST) | Characterization of Sludges. Filtration Properties. Part 1: Capillary Suction Time (CST) |
| BS EN 15336-2007 | 粘合剂.静负荷状态下胶粘件断裂时间的测定 | Adhesives - Determination of the time to rupture of bonded joints under static load |
| BS EN 15416-5-2006 | 苯酚和氨基塑料除外的负荷轴承木结构的粘结剂.试验方法.常规加压时间测定 | Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of conventional pressing time |
| BS EN 15617-2009 | 焊接接头的无损检验.飞行时间衍射技术(TOFD).接受等级 | Non-destructive testing of welds - Time-of-flight diffraction technique (TOFD) - Acceptance levels |
| BS EN 1744-6-2006 | 集料的化学性能试验.再生集料萃取对水泥最初凝固时间影响的测定 | Tests for chemical properties of aggregates - Determination of the influence of recycled aggregate extract on the initial setting time of cement |
| BS EN 1811-1998+A1-2008 | 镍由产品上释放试图直接和长时间与皮肤接触的参考试验方法 | Reference test method for release of nickel from products intended to come into direct and prolonged contact with the skin |
| BS EN 2349-304-2006 | 航空航天系列.继电器和电流接触器用要求和试验程序.第304部分:工作和释放时间 | Aerospace series — Requirements and test procedures for relays and contactors — Part 304: Operate and release time |
| BS EN 2349-305-2006 | 航空航天系列.继电器和电流接触器的要求和试验程序.第305部分:释放时间 | Aerospace series - Requirements and test procedures for relays and contactors - Part 305: Bounce time |
| BS EN 28601-1989 | 信息交换中日期和时间显示规范 | Specification for representation of dates and times in information interchange |
| BS EN 302-6-2004 | 承重木结构用胶粘剂.试验方法.常规加压时间的测定 | Adhesives for load-bearing timber structures - Test methods - Determination of the conventional pressing time |
| BS EN 480-2-2006 | 混凝土、灰浆和薄泥浆混合物.试验方法.凝固时间的测定 | Admixtures for concrete, mortar and grout - Test methods - Determination of setting time |
| BS EN 60068-2-57-2000 | 环境试验.试验方法.试验Ff.振动.时间系列法 | Environmental testing - Test methods - Test Ff - Vibration - Time-history method |
| BS EN 60255-3-1998 | 继电器.与时间有关或无关的单输入励磁质量测量继电器 | Electrical relays - Single input energizing quantity measuring relays with dependent or independent time |
| BS EN 60461-2001 | 录像机的时间和控制规则 | Time and control code for video tape recorders |
| BS EN 61280-2-10-2005 | 纤维光学通信子系统试验规程.数字系统.激光发射器的时间分辨线性调频脉冲和α指数测量 | Fibre optic communication subsystem test procedures - Digital systems - Time-resolved chirp and alpha-factor measurement of laser transmitters |
| BS EN 61300-3-21-1998 | 光纤互联装置和无源部件.基本试验和测量程序.检验和测量.开关时间和回跳时间 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Examinations and measurements - Examinations and measurements - Switching time and bounce time |
| BS EN 61811-54-2002 | 经质量评定的机电式"非”规定时间全有或全无继电器.空白详细规范.经质量评定的机电式"全有"或"全无”通讯继 | Electromechanical non-specified time all-or-nothing relays of assessed quality - Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Two change-over contacts, 15 mm x 7,5 mm base |
| BS EN 61811-55-2002 | 经质量评定的无规定时间的“全有或全无”机电继电器.空白详细规范.经质量评定的"全有或全无"机电电信继电器 | Electromechanical non-specified time all-or-nothing relays of assessed quality - Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Two change-over contacts, 11 mm x 7,5 mm (max.) base |
| BS EN 62374-2007 | 半导体装置.依赖时间的栅极介电薄膜的介质击穿(TDDB)试验 | Semiconductor devices - Time dependent dielectric breakdown (TDDB) test for gate dielectric films |
| BS EN 62375-2005 | 视频系统(625/50改进的).使用垂直消隐时间的视频和伴随数据.模拟接口 | Video systems (625/50 progressive) - Video and accompanied data using the vertical blanking interval - Analogue interface |
| BS EN 728-1997 | 塑料管和管道系统.聚烯烃管和配件.氧化诱导时间的测定 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| BS EN ISO 11554-2008 | 光学和光子学.激光和相关激光设备.激光束功率、能量和时间特性的试验方法 | Optics and photonics - Lasers and laser-related equipment - Test methods for laser beam power, energy and temporal characteristics |
| BS EN ISO 12625-8-2006 | 薄纸和薄纸制品.对篮子沉浸吸水时间和吸水能力的试验办法 | Tissue paper and tissue products - Water-absorption time and water-absorption capacity, basket-immersion test method |
| BS EN ISO 2431-1996 | 色漆和清漆.用流量杯测定流动时间 | Paints and varnishes - Determination of flow time by use of flow cups |
| BS EN ISO 2535-2002 | 塑料.未饱和的聚酯树脂.室温时的胶凝时间的测量 | Plastics - Unsaturated polyester resins - Measurement of gel time at ambient temperature |
| BS EN ISO 2578-1993 | 塑料.长期暴露于热作用后时间和温度极限值的测定 | Plastics - Determination of the time-temperature limits after prolonged exposure to heat |
| BS EN ISO 3382-2-2008 | 声学.房间声音参数的测量.普通房间的混响时间 | Acoustics - Measurement of room acoustic parameters - Part 2:Reverberation time in ordinary rooms |
| BS EN ISO 3382-2000 | 声学.根据其它声学参数测量厅堂混响时间 | Acoustics - Measurement of the reverberation time of rooms with reference to other acoustical parameters |
| BS EN ISO 4490-2008 | 金属粉末.使用校准漏斗(霍尔流量计)方法测定流动时间 | Metallic powders - Determination of flow time by means of a calibrated funnel (Hall flowmeter) |
| BS EN ISO 9073-13-2007 | 纺织品.非织造织物的试验方法.重复液体渗透时间 | Textiles - Test methods for nonwovens - Repeated liquid strike-through time |
| BS EN ISO 9073-8-1998 | 纺织品.无纺织物的试验方法.液体渗透时间的测定(模拟尿) | Textiles - Test methods for nonwovens - Determination of liquid strike-through time (simulated urine) |
| BS EN ISO 9396-2001 | 塑料.酚醛树脂.用自动装置测定在给定温度下的凝胶时间 | Plastics - Phenolic resins - Determination of the gel time at a given temperature using automatic apparatus |
| BS ISO 10791-9-2001 | 加工中心的试验条件.刀具更换和托架更换所用时间的估计 | Test conditions for machining centres - Evaluation of the operating times of tool change and pallet change |
| BS ISO 11104-2004 | 空间数据和信息转换系统.时间码格式 | Space data and information transfer systems - Time code formats |
| BS ISO 11222-2007 | 空气质量.空气质量测量所需平均时间不确定度的测定 | Air quality - Determination of the uncertainty of the time average of air quality measurements |
| BS ISO 11357-5-2001 | 塑料.差示扫描量热法(DSC).特性的测定：反应曲线温度、时间、反应焓和转化度 | Plastics - Differential scanning calorimetry (DSC) - Determination of characteristic reaction-curve temperatures and times, enthalphy of reaction and degree of conversion |
| BS ISO 11357-6-2008 | 塑料.差示扫描量热法(DSC).氧化诱导时间(等温OIT)和氧化感应温度(动力OIT)的测定 | Plastics - Differential scanning calorimetry (DSC) - Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| BS ISO 12238-2001 | 气压液动.方向控制阀门.转换时间的测量 | Pneumatic fluid power - Directional control valves - Measurement of shifting time |
| BS ISO 13202-2003 | 起重机.速度和时间参数的测量 | Cranes - Measurement of velocity and time parameters |
| BS ISO 15040-1999 | 复合物.预浸胶体.胶凝时间的测定 | Composites - Prepregs - Determination of gel time |
| BS ISO 16000-8-2007 | 室内空气.建筑物特征通风条件下局部空气存留时间的测定 | Indoor air - Determination of local mean ages of air in buildings for characterizing ventilation conditions |
| BS ISO 17514-2005 | 时间测量仪表.荧光镀层.试验方法和要求 | Time-measuring instruments - Photoluminescent deposits - Test methods and requirements |
| BS ISO 24033-2009 | 耐升温的聚乙烯管道(PE-RT).时间和温度对预期强度的影响 | Polyethylene of raised temperature resistance (PE-RT) pipes - Effect of time and temperature on the expected strength |
| BS ISO 80000-3-2007 | 量和单位.空间和时间 | Quantities and units - Space and time |
| BS ISO 8601-2005 | 数据元和交换格式.信息交换.日期和时间表示法 | Data elements and interchange formats - Information interchange - Representation of dates and times |
| BS ISO/IEC 18014-1-2008 | 信息技术.安全技术.时间标记设施.框架 | Information technology - Security techniques - Time- stamping services - Framework |
| BS ISO/IEC 18014-2-2003 | 信息技术.安全技术.时间标记业务.产生独立标记的机械 | Information technology - Security techniques - Time-stamping services - Mechanisms producing independent tokens |
| BS ISO/IEC 18014-3-2004 | 信息技术.安全技术.时间标记业务.链接标记产生机制 | Information technology - Security techniques - Time-stamping services - Mechanisms producing linked tokens |
| BS ISO/IEC ISP 11185-13-1995 | 信息技术.国际标准数据区FVT2nn.虚拟终端的基本分类.控制对象类型定义寄存器.第13部分:FTV2111.等待时间控 | Information technology - International standardized profiles FVT2nn - Virtual terminal basic class - Register of control object type definitions - FVT2111 - Waiting time control object |
| BS ISO/TR 12765-1999 | 封闭式管道中液体流量的测量.使用转接-时间超声流量计法 | Measurement of fluid flow in closed conduits - Methods using transit-time ultrasonic flowmeters |
| DD ENV 12381-1997 | 保健信息.保健特殊问题的时间标准 | Health care informatics. Time standards for healthcare specific problems |
| DD ENV 12625-8-2001 | 薄页纸和薄纸产品.水吸收时间,水吸收能力,手工和自动试验方法 | Tissue paper and tissue products. Water absorption time, water absorption capacity. Manual and automated test method |
| DD ENV 302-5-2002 | 承重木材结构件用胶粘剂.试验方法.常规组装时间的测定 | Adhesives for load-bearing timber structures. Test tethods. Determination of the conventional assembly time |
| 编号 | 中文名称 | 英文名称 |